manual/rockbox_interface/main.tex

   1 % $Id$ %
   2 \chapter{\label{ref:rockbox_interface}Quick Start}
   3 \section{Basic Overview}
   4 \subsection{The \daps{} controls}
   5
   6 \begin{center}
   7 % include the front image. Using \specimg makes this fairly easy,
   8 % but requires to use the exact value of \specimg in the filename!
   9 % The extension is selected in the preamble, so no further \ifpdfoutput
  10 % is necessary.
  11 \includegraphics[height=8cm,width=10cm,keepaspectratio=true]{rockbox_interface/images/\specimg-front}
  12 \opt{m3}{% replace with HAVEREMOTEKEYMAP when the h100 file exists or change specimg
  13   \end{center}
  14   % spacing between the two pictures, could possibly be improved
  15   \begin{center}
  16     \includegraphics[height=5.6cm,width=10cm,keepaspectratio=true]{rockbox_interface/images/\specimg-remote}
  17 }
  18 \end{center}
  19
  20 Throughout this manual, the buttons on the \dap{} are labelled according to the
  21 picture above. Whenever a button name is prefixed by ``Long'', a long press of
  22 approximately one second should be performed on that button. The buttons are
  23 described in detail in the following paragraph.
  24
  25 \blind{
  26   Additional information for blind users is available on the Rockbox website at
  27   \wikilink{BlindFAQ}.
  28
  29   %
  30   \opt{h100}{
  31   Hold or lay the \dap{} so that the side with the joystick and LCD is facing
  32   towards you, and the curved side is at the top. The joystick functions as
  33   the \ButtonUp{}, \ButtonRight{}, \ButtonLeft{}, and \ButtonDown{} buttons when
  34   pressed in the appropriate direction. Pressing the joystick down functions as
  35   \ButtonSelect{}.
  36   On the right side of the \dap{} are the \ButtonOn{}, \ButtonOff{},
  37   \ButtonMode{} buttons, and the \ButtonHold{} switch. When this switch is
  38   switched towards the bottom of the \dap{}, hold is on, and none of the other
  39   buttons have any effect.
  40
  41   On the left side is the \ButtonRec{} button. Above that is the internal microphone.
  42
  43   On the top panel of the \dap{}, from left to right, you can find the
  44   following: headphone mini jack plug, remote port, Optical line-in, Optical Line-out.
  45
  46   On the bottom panel of the \dap{}, from left to right, you can find the
  47   following: power jack, reset switch, and USB port. In the event that your
  48   \dap{} hard locks, you can reset it by inserting a paper clip into the hole
  49   where the reset switch is.}
  50   %
  51   \opt{h300}{
  52   Hold or lay the \dap{} so that the side with the button pad and
  53   LCD is facing towards you.  The buttons on the button pad are as follows:  top
  54   left corner: \ButtonOn{}, bottom left corner: \ButtonOff{}, top right corner:
  55   \ButtonRec, bottom right corner: \ButtonMode{}.  In the center of the button pad
  56   is a button labelled \ButtonSelect{}.  Surrounding the \ButtonSelect{} button are
  57   the \ButtonUp{}, \ButtonDown{}, \ButtonLeft{}, and \ButtonRight{} buttons.
  58
  59   On the top panel of the \dap{}, from left to right, you can find the
  60   following: headphone mini jack plug, remote port, Line-in, Line-out.
  61
  62   On the left hand side of the \dap{} is the internal microphone. Just underneath
  63   this is a small hole, the reset switch. In the event that your \dap{} hard locks,
  64   you can reset it by inserting a paper clip into the hole where the reset switch
  65   is.
  66
  67   On the right hand side of the \dap{} is the \ButtonHold{} switch. When this is
  68   switched towards the bottom of the \dap{}, hold is on, and none of the other
  69   buttons have any effect.
  70
  71   On the bottom panel of the \dap{}, from left to right, you can find the
  72   following:  power jack and two USB ports.  The USB port on the right is used
  73   to connect your \dap{} to your computer.  The USB port on the left is not
  74   used in Rockbox.
  75   }
  76   %
  77   \opt{ipod4g,ipodcolor,ipodvideo,ipodmini}{
  78   The main controls on the \dap{} are a slightly indented scroll wheel
  79   with a flat round button in the center. Hold the \dap{} with these controls
  80   facing you.
  81
  82   The top of the player will have the following, from left to
  83   right:
  84   \opt{ipod4g,ipodcolor}{remote connector, headphone jack, \ButtonHold{}
  85     switch.}
  86   \opt{ipodvideo}{\ButtonHold{} switch, headphone jack.}
  87   \opt{ipodmini}{\ButtonHold{} switch, remote connector, headphone jack.}
  88
  89   The dock connector that is used to connect your \dap{} to your computer is on
  90   the bottom panel of the \dap{}.
  91
  92   The button in the middle of the wheel is called \ButtonSelect{}. You can
  93   operate the wheel by pressing the top, bottom, left or right sections,
  94   or by sliding your finger around it.  The top is \ButtonMenu{}, the bottom is
  95   \ButtonPlay{}, the left is \ButtonLeft{}, and the right is \ButtonRight{}.
  96   When the manual says to \ButtonScrollFwd{}, it means to slide your finger
  97   clockwise around the wheel. \ButtonScrollBack{} means to slide your finger
  98   counterclockwise. Note that the wheel is sensitive, so you will need to move
  99   slowly at first and get a feel for how it works.
 100
 101   Note that when the \ButtonHold{} switch is pushed toward the center of the \dap{},
 102   hold is on, and none of the other controls do anything.  Be sure
 103   \ButtonHold{} is off before trying to use your player.
 104   }
 105   %
 106   \opt{ipod3g}{
 107   The main controls on the \dap{} are a slightly indented touch wheel
 108   with a flat round button in the center, and four buttons in a row above the
 109   touch wheel. Hold the \dap{} with these controls
 110   facing you.
 111
 112   The top of the player will have the following, from left to
 113   right: remote connector, headphone jack, \ButtonHold{} switch.
 114
 115   The dock connector that is used to connect your \dap{} to your computer is on
 116   the bottom panel of the \dap{}.
 117
 118   The button in the middle of the wheel is called \ButtonSelect{}. You can
 119   operate the wheel by sliding your finger around it.  The row of
 120   buttons consists of, from left to right, the \ButtonLeft{},
 121   \ButtonMenu{}, \ButtonPlay{}, and \ButtonRight{} buttons.
 122   When the manual says to \ButtonScrollFwd{}, it means to slide your finger
 123   clockwise around the wheel. \ButtonScrollBack{} means to slide your finger
 124   counterclockwise. Note that the wheel is sensitive, so you will need to move
 125   slowly at first and get a feel for how it works.
 126
 127   Note that when the \ButtonHold{} switch is pushed toward the center of the \dap{},
 128   hold is on, and none of the other controls do anything.  Be sure
 129   \ButtonHold{} is off before trying to use your player.
 130   }
 131   %
 132   \opt{ipod1g2g}{
 133   The main controls on the \dap{} are a slightly indented wheel
 134   with a flat round button in the center, and four buttons surrounding
 135   it. On the 1st generation iPod, this wheel physically turns. On the
 136   2nd generation iPod, this wheel is touch-sensitive. Hold the \dap{} with these controls
 137   facing you.
 138
 139   The top of the player will have the following, from left to
 140   right: FireWire port, headphone jack, \ButtonHold{} switch.
 141
 142   The FireWire port is used to connect your \dap{} to the computer and
 143   to charge its battery via a wall charger.
 144
 145   The button in the middle of the wheel is called \ButtonSelect{}. You can
 146   operate the wheel by turning it, or sliding your finger around
 147   it. The top is \ButtonMenu{}, the bottom is \ButtonPlay{}, the left
 148   is \ButtonLeft{}, and the right is \ButtonRight{}.
 149   When the manual says to \ButtonScrollFwd{}, it means to slide your finger
 150   clockwise around the wheel. \ButtonScrollBack{} means to slide your finger
 151   counterclockwise. Note that the wheel is sensitive, so you will need to move
 152   slowly at first and get a feel for how it works.
 153
 154   Note that when the \ButtonHold{} switch is pushed toward the center of the \dap{},
 155   hold is on, and none of the other controls do anything.  Be sure
 156   \ButtonHold{} is off before trying to use your player.
 157   }
 158   %
 159   \opt{ipodnano}{
 160   The main controls on the \dap{} are a slightly indented wheel with a
 161   flat round button in the center. Hold the \dap{} with these controls on the
 162   top surface. There is a \ButtonHold{} switch at one end, and
 163   headphone and dock connector at the other; be sure the end with the
 164   switch is facing away from you.
 165
 166   The button in the middle of the wheel is called \ButtonSelect{}. You can
 167   operate the wheel by pressing the top, bottom, left or right sections,
 168   or by sliding your finger around it.  The top is \ButtonMenu{}, the bottom is
 169   \ButtonPlay{}, the left is \ButtonLeft{}, and the right is \ButtonRight{}.
 170   When the manual says to \ButtonScrollFwd{}, it means to slide your finger
 171   clockwise around the wheel. \ButtonScrollBack{} means to slide your finger
 172   counterclockwise. Note that the wheel is sensitive, so you will need to move
 173   slowly at first and get a feel for how it works.
 174
 175   Note that when the \ButtonHold{} switch is pushed toward the center of the \dap{},
 176   hold is on, and none of the other controls do anything; be sure \ButtonHold{} is
 177   off before trying to use your player.
 178   }
 179   %
 180   \opt{ondio}{
 181   The main characteristic of the Ondio case is the indent on its lower right side,
 182   which is the MMC slot. Holding the \dap{} with this slot in the described position
 183   you'll find the following:
 184
 185   On the curved top, from left to right, are the headphone jack,
 186   the \ButtonOff{} button,%
 187   \opt{recording}{ and the line in jack}.
 188   Apart from the already mentioned MMC slot, you will find the USB connector on
 189   the \daps{} right side. Below the LCD, at approximately the center of the \dap{},
 190   there is the main button pad of the \dap{}. The centre of the button pad dips inward
 191   and helps to operate the directional keys from there. Located on a two-way button
 192   strip are the \ButtonLeft{} and \ButtonRight{} keys, with \ButtonUp{} above it
 193   and \ButtonDown{} below it. The raised button positioned in the lower left of this
 194   round crosspad is labelled \ButtonMenu{}.
 195   }
 196   %
 197   \opt{h10,h10_5gb}{
 198   Hold or lay the \dap{} so that the side with the scroll pad and
 199   LCD is facing towards you. In the centre below the lcd is the scroll pad. It
 200   is oriented vertically. Touching the top and bottom half of it acts as the
 201   \ButtonScrollUp{}  and \ButtonScrollDown{} buttons respectively. On the left
 202   of the scroll pad is the \ButtonLeft{} button and on the right is the
 203   \ButtonRight{} button.
 204
 205   There are three buttons on the right hand side of the \dap{}. From top to
 206   bottom, they are: \ButtonRew{}, \ButtonPlay{} and \ButtonFF{}. On the left
 207   hand side is the \ButtonPower{} button.
 208
 209   On the top panel of the \dap{}, from left to right, you can find the
 210   following: \ButtonHold{} switch, \opt{h10}{reset pin hole, }remote port and
 211   headphone mini jack plug.
 212
 213   On the bottom panel of the \dap{} is the data cable port.}
 214   %
 215   \opt{gigabeatf}{
 216   \note{The following description is for the Gigabeat F, but can also apply for the
 217   Gigabeat X. The Gigabeat F is slightly larger and more rectangular shaped, while the
 218   Gigabeat X is smaller and has a slightly tapered back.}
 219
 220   Hold the \dap{} with the screen on top and the controls on the right hand side.
 221   Below the screen is a cross-shaped touch sensitive pad which contains the
 222   \ButtonUp{}, \ButtonDown{}, \ButtonLeft{} and \ButtonRight{} controls.  On the
 223   Gigabeat X, this pad will feel slightly raised up, while it will feel slightly
 224   sunken in on the Gigabeat F. On the top of the unit, from left to right, are the
 225   power socket, the \ButtonHold{} switch, and the headphone socket.  The
 226   \ButtonHold{} switch puts the \dap{} into hold mode when it is switched to the
 227   right of the unit. The buttons will have no effect when this is the case.
 228
 229   Starting from the left hand side on the bottom of the unit, nearer to the front
 230   than the back, is a recessed switch which
 231   controls whether the battery is on or off.  When this switch is to the left,
 232   the battery is disconnected.  This can be used for a hard reset of the unit,
 233   or if the \dap{} is being placed in storage.  Next to that is a connector for
 234   the docking station and finally on the right hand side of the bottom of the
 235   unit is a mini USB socket for connecting directly to USB.
 236
 237   Finally on the right hand side of the unit are some control buttons.  Going from
 238   the bottom of the unit to the top there is a small round \ButtonA{} buttton then a
 239   rocker volume switch with of the \ButtonVolDown{} button below the \ButtonVolUp{}
 240   button.  Above that is are two more small round buttons, the \ButtonMenu{}
 241   button and nearest to the top of the unit the \ButtonPower{} button, which is held
 242   down to turn the \dap{} on or off. If you have a Gigabeat X, these buttons are small
 243   metallic buttons that are place further up on the right hand side, and closer
 244   together. The layout is still the same, however.}
 245   %
 246   \opt{gigabeats}{
 247   Hold the \dap{} with the screen on top and the controls on the right hand side.
 248   Directly below the bottom edge of the screen are two buttons, \ButtonBack{}
 249   on the left and \ButtonMenu{} on the right. Below them is a cross-shaped pad
 250   which contains the \ButtonUp{}, \ButtonDown{}, \ButtonLeft{}, \ButtonRight{}
 251   and \ButtonSelect{} controls.
 252   On the top of the unit from left to right are the headphone socket and the
 253   \ButtonHold{} switch.  The \ButtonHold{} switch puts the \dap{} into
 254   hold mode when it is switched to the right of the unit.
 255   The buttons will have no effect when this is the case.
 256
 257   Starting from the left hand side on the bottom of the unit, nearer to the back
 258   than the front, is a recessed switch which controls whether the battery is on
 259   or off.  When this switch is to the left, the battery is disconnected.
 260   This can be used for a hard reset of the unit, or if the \dap{} is being placed
 261   in storage.  Next to that is a mini USB socket for connecting directly to USB,
 262   and finally a custom connector, presumably for planned accessories which were
 263   never released.
 264
 265   Finally on the right hand side of the unit are some control buttons and the power
 266   connector.  Going from the bottom of the unit to the top, there is the power
 267   connector socket, followed by three small round buttons, the
 268   \ButtonNext{} buttton, \ButtonPlay{} button, and \ButtonPrev{} button (from bottom
 269   to top) then a rocker volume switch with of the \ButtonVolDown{} button below the
 270   \ButtonVolUp{} button.  Above that is one more small round button, the \ButtonPower{}
 271   button, which is held down to turn the \dap{} on or off.}
 272   %
 273   \opt{mrobe100}{
 274   Hold the \dap{} with the black front facing you such that the m:robe writing
 275   is readable. Below the writing is the touch sensitive pad with the
 276   \ButtonMenu{}, \ButtonPlay{}, \ButtonLeft{}, \ButtonRight{} and \ButtonDisplay
 277   controls indicated by their symbols. The dotted center strip is devided in
 278   three parts: \ButtonUp{}, \ButtonSelect{} and \ButtonDown. On the top of the
 279   unit, on the right, is the \ButtonPower{} switch, which is held down to turn
 280   the \dap{} on or off.
 281
 282   The \ButtonHold{} switch is located on the left of the \dap{}, below the
 283   headphone socket. It puts the \dap{} into hold mode when it is switched to the
 284   top of the unit. The buttons will have no effect when this is the case. On the
 285   bottom of the unit, there is a connector for the docking station or the
 286   proprietary USB connector for connecting directly to USB.}
 287   %
 288   \opt{x5,m5}{
 289   The \dap{} is curved so that the end with the screen on it is thicker than the
 290   other end.  Hold the \dap{} wih the thick end towards the top and the screen
 291   facing towards you.  Half way up the front of the unit on the right hand side
 292   is a four way joystick which is the \ButtonUp{}, \ButtonDown{},
 293   \ButtonLeft{}, and \ButtonRight{} buttons. When pressed it serves as \ButtonSelect{}.
 294
 295   On the right hand side of the \dap{} from top to bottom, first there is a two
 296   way switch.  the \ButtonPower{} button is activated by pushing this switch up,
 297   and pushing this switch down until it clicks slightly will activate the
 298   \ButtonHold{} button.  When the switch is in this position, none of the other
 299   keys will have an effect.
 300
 301   Below the switch is a lozenge shaped button which is the \ButtonRec{}
 302   button, and below that the final button on this side of the unit, the
 303   \ButtonPlay{} button.  Just below this is a small hole which is difficult to
 304   locate by touch which is the internal microphone.  At the very bottom of
 305   this side of the unit is the reset hole, which can be used to perform a hard
 306   reset by inserting a paper clip.
 307
 308   On the bottom of the unit is the connector for the
 309   \playerman{} subpack or dock.  On the top of the unit is a charge
 310   indicator light, which may feel a bit like a button, but is not.
 311
 312   From the top of the \dap{} on the left hand side is the headphone socket, then the
 313   remote connector.  Below this is a cover which protects the \opt{x5}{USB host
 314   connector.}\opt{m5}{USB and charging connector}.}
 315   %
 316   \opt{e200}{
 317   Hold the \dap{} with the turning wheel at the front and bottom.  On the bottom left
 318   of the front of the \dap{} is a raised round button, the \ButtonPower{} button.
 319   Above and to the left of this, on the outside of the turning wheel are four
 320   buttons.  These are the \ButtonUp{}, \ButtonDown{}, \ButtonLeft{} and
 321   \ButtonRight{} buttons.  Inside the wheel is the \ButtonSelect{} button.  Turning
 322   the wheel to the right activates the \ButtonScrollFwd{} function, and to the
 323   left, the \ButtonScrollBack{} function.
 324
 325   On the right of the unit is a slot for inserting flash cards.  On the bottom is
 326   the connector for the USB cable.  On the left is the \ButtonRec{} button, and
 327   on the top, there is the headphone socket to the right, and the \ButtonHold{}
 328   switch.  Moving this switch to the right activates hold mode in which none of the
 329   other buttons have any effect.  Just to the left of the \ButtonHold{} switch is a
 330   small hole which contains the internal microphone.}
 331   %
 332   \opt{c200}{
 333   Hold the \dap{} with the buttons on the right and the screen on the left. On
 334   the right side of the unit, there is a series of four connected buttons that
 335   form a square. The four sides of the square are the \ButtonUp{},
 336   \ButtonDown{}, \ButtonLeft{} and \ButtonRight{} buttons, respectively. Inside
 337   the square formed by these four buttons is the \ButtonSelect{} button. At the
 338   bottom right corner of the square is a small separate button, the
 339   \ButtonPower{} button.
 340
 341   Moving clockwise around the outside of the unit, on the top are the \ButtonVolUp{}
 342   and \ButtonVolDown{} buttons, which control the volume of playback. The buttons can
 343   be distinguished by a sunken triangle on the \ButtonVolDown{} button, and a
 344   raised triangle on the \ButtonVolUp{} button. To the right of
 345   the volume buttons on the top of the unit is the slot for inserting flash
 346   memory cards. On the right side of the unit is the connector for the USB
 347   cable. At center of the bottom of the \dap{} is the \ButtonRec{} button. To
 348   the left of the \ButtonRec{} button is the \ButtonHold{} switch. Moving this
 349   switch to the right activates hold mode, in which none of the other buttons
 350   have any effect. On the lower left side of the unit is the headphone socket.
 351   Immediately above the headphone socket is a lanyard loop and the microphone.
 352   }
 353   %
 354   \opt{clip}{
 355   Hold the \dap{} with the controls on the bottom and the screen on the top. The main
 356   controls are a four-way pad with a button in the centre; pressing this centre button
 357   functions as \ButtonSelect{}. Going clockwise from the top, the four-way pad contains
 358   the \ButtonUp{}, \ButtonRight{}, \ButtonDown{}, and \ButtonLeft{} buttons.
 359   Immediately above and to the right of the four-way pad is the \ButtonHome{} button.
 360
 361   On the left hand panel is a two way switch. Pressing this switch up acts as
 362   \ButtonPower{}, and clicking it down until it locks acts as the \ButtonHold{}
 363   switch. When the \ButtonHold{} switch is on, none of the other buttons have any
 364   effect. Immediately above the switch is a mini-USB port to connect the \dap{} to
 365   a computer.
 366
 367   On the right hand panel is a two-way button that acts as \ButtonVolDown{} when
 368   pressed on the bottom, and \ButtonVolUp{} when pressed on the top. Immediately
 369   above this button is the headphone jack.
 370   }
 371   %
 372   \opt{player}{
 373   The main controls of this player are a four-way button on the right below
 374   the screen, and two round buttons to the left of it. Hold the \dap{} with
 375   these controls on the bottom and facing you.
 376
 377   On the left hand side, the higher of the two small buttons is the \ButtonOn{},
 378   the lower of the two buttons is the \ButtonMenu{} button. The large circular
 379   button on the right contains, clockwise from the top, the \ButtonPlay{},
 380   the \ButtonRight{}, the \ButtonStop{}, and the \ButtonLeft{} buttons.
 381
 382   On the top on the \dap{} is the headphone jack on the left and the Line-Out
 383   jack on the right. On the bottom of the \dap{} is the Line-In jack on the left,
 384   the DC-In jack on the right, and the USB connector in the centre.
 385   }
 386   %
 387   \opt{recorder}{
 388   Holding the Jukebox in front of you, there should be three rectangular buttons
 389   in a horizontal line towards the middle of the unit, and below this to the left
 390   there is a circular four button array with the circular \ButtonPlay{} button
 391   as a fifth button in the centre. These are the navigation controls. Below the
 392   rectangular buttons and to the right of the circular buttons are two small round
 393   buttons one above the other.
 394
 395   The \ButtonOn{} button is the topmost of the two buttons located below and to the
 396   left of the navigation controls whereas the lower of these two is called \ButtonOff.
 397   The small round button in the middle of the large circular button array is called
 398   \ButtonPlay{} button. To the right of the \ButtonPlay{} button there is the
 399   \ButtonRight{} button, left of it is the \ButtonLeft{}, above it \ButtonUp, and
 400   below the \ButtonPlay{} button there is the \ButtonDown{} button placed. In the row
 401   of three rectangular buttons the following buttons can be found (from left to right):
 402   \ButtonFOne{}, \ButtonFTwo{} and \ButtonFThree{}.
 403
 404   On the top of the \dap{} is the headphone jack on the left and the Line-Out jack on
 405   the right. On the bottom of the \dap{} is the Line-In jack on the left, the
 406   DC-In jack on the right, and the USB connector in the centre.
 407   }
 408   \opt{recorderv2fm}{
 409   Holding the Jukebox in front of you, there should be three rectangular buttons
 410   in a horizontal line towards the middle of the unit, and below this centred on the
 411   middle button there are four radial arc shaped buttons placed in a cross formation
 412   with the circular play button as the centre of the cross. These are the navigation
 413   controls. Below the cross and to the left are two other buttons.
 414
 415   The \ButtonOn{} button is the leftmost of the two buttons located below and to the
 416   left of the navigation controls whereas the rightmost and little lower one of
 417   these two is called \ButtonOff{}. The round button raised slightly higher than the
 418   others in the centre of the navigation controls is the \ButtonPlay{} button.  To
 419   the right of the \ButtonPlay{} button  there is the \ButtonRight{} button, left of
 420   it is the \ButtonLeft{}, above it \ButtonUp{}, and below the \ButtonPlay{} button
 421   there is the \ButtonDown{} button  placed. In the row of three rectangular buttons
 422   the following buttons can be found (from left to right): \ButtonFOne{}, \ButtonFTwo{}
 423   and \ButtonFThree{}.
 424   }
 425 }
 426
 427 \subsection{Turning the \dap{} on and off}
 428 To turn on and off your Rockbox enabled \dap{} use the following keys:
 429   \begin{table}
 430     \begin{btnmap}{}{}
 431       \opt{IRIVER_H100_PAD,IRIVER_H300_PAD}{\ButtonOn}%
 432       \opt{IPOD_4G_PAD}{\ButtonMenu{} / \ButtonSelect}%
 433       \opt{IPOD_3G_PAD}{\ButtonMenu{} / \ButtonPlay}%
 434       \opt{ONDIO_PAD}{\ButtonOff}\opt{RECORDER_PAD,PLAYER_PAD}%
 435           {Long \ButtonOn}%
 436       \opt{IAUDIO_X5_PAD,IRIVER_H10_PAD,SANSA_E200_PAD,SANSA_C200_PAD,GIGABEAT_PAD,MROBE100_PAD,GIGABEAT_S_PAD,sansaAMS}
 437           {\ButtonPower}%
 438     \opt{HAVEREMOTEKEYMAP}{&
 439       \opt{IRIVER_RC_H100_PAD}{\ButtonRCOn}%
 440           }
 441       & Start Rockbox\\
 442       \opt{IRIVER_H100_PAD,IRIVER_H300_PAD}{Long \ButtonOff}%
 443       \opt{IPOD_4G_PAD,IPOD_3G_PAD}{Long \ButtonPlay}%
 444       \opt{ONDIO_PAD,recorderv2fm}{Long \ButtonOff}%
 445       \opt{recorder}{Double tap \ButtonOff\ when playback is stopped}%
 446       \opt{PLAYER_PAD}{From the Main Menu, select \textbf{Shutdown}}%
 447       \opt{IAUDIO_X5_PAD,IRIVER_H10_PAD,SANSA_E200_PAD,SANSA_C200_PAD,GIGABEAT_PAD,MROBE100_PAD,GIGABEAT_S_PAD,sansaAMS}%
 448           {Long \ButtonPower}%
 449     \opt{HAVEREMOTEKEYMAP}{&
 450       \opt{IRIVER_RC_H100_PAD}{Long \ButtonRCStop}%
 451           }
 452       & Shutdown Rockbox\\
 453     \end{btnmap}
 454   \end{table}
 455
 456 \label{ref:Safeshutdown}On shutdown, Rockbox automatically saves its settings.
 457
 458 \opt{IRIVER_H100_PAD,IRIVER_H300_PAD,IAUDIO_X5_PAD,SANSA_E200_PAD%
 459   ,SANSA_C200_PAD,IRIVER_H10_PAD,IPOD_4G_PAD,GIGABEAT_PAD}{%
 460   If you have problems with your settings, such as accidentally having
 461   set the colours to black on black, they can be reset at boot time.  See
 462   the Reset Settings in \reference{ref:manage_settings_menu} for details.
 463 }%
 464
 465 \opt{PLAYER_PAD,RECORDER_PAD,ONDIO_PAD,GIGABEAT_PAD,IPOD_4G_PAD,SANSA_E200_PAD%
 466 ,SANSA_C200_PAD,IAUDIO_X5_PAD,IAUDIO_M5_PAD,IPOD_3G_PAD}{%
 467   In the unlikely event of a software failure, hardware poweroff or reset can be
 468   performed by holding down \opt{PLAYER_PAD}{\ButtonStop}\opt{RECORDER_PAD,ONDIO_PAD}
 469   {\ButtonOff}\opt{GIGABEAT_PAD}{the battery switch}\opt{IPOD_4G_PAD}
 470   {\ButtonMenu + \ButtonSelect}\opt{IPOD_3G_PAD}{\ButtonMenu + \ButtonPlay}
 471   \opt{SANSA_E200_PAD,SANSA_C200_PAD,IAUDIO_X5_PAD,IAUDIO_M5_PAD}
 472   {\ButtonPower} until the \dap{} shuts off or reboots.
 473 }%
 474 \opt{IRIVER_H100_PAD,IRIVER_H300_PAD,IAUDIO_M3_PAD,IRIVER_H10_PAD,MROBE100_PAD}{%
 475   In the unlikely event of a software failure, a hardware reset can be
 476   performed by inserting a paperclip gently into the Reset hole.
 477 }%
 478
 479 \nopt{gigabeatf,m3,m5,x5,archos}
 480   {
 481   \subsection{Starting the original firmware}
 482   \label{ref:Dualboot}
 483   \opt{ipod4g,ipodcolor,ipodvideo,ipodnano,ipodmini}
 484     {
 485     Rockbox has a dual-boot feature. To boot into the original firmware, shut
 486     down the device as described above. Turn on the \ButtonHold{} switch
 487     immediately after turning the player on. The Apple logo will
 488     display for a few seconds as Rockbox loads the original firmware.
 489
 490     You can also load the original firmware by shutting down the device,
 491     then clicking the \ButtonHold{} switch on and connecting the iPod
 492     to your computer.
 493
 494     Regardless of which method you use to boot to the original firmware, you can
 495     return to Rockbox by pressing and holding \ButtonMenu{} and \ButtonSelect{}
 496     simultaneously until the player hard resets.
 497     }
 498
 499   \opt{ipod1g2g,ipod3g}
 500     {
 501     Rockbox has a dual-boot feature. To boot into the original firmware, shut
 502     down the device as described above. Turn on the \ButtonHold{} switch
 503     immediately after turning the player on. The Apple logo will
 504     display for a few seconds as Rockbox loads the original firmware.
 505
 506     You can also load the original firmware by shutting down the device,
 507     then clicking the \ButtonHold{} switch on and connecting the iPod
 508     to your computer.
 509
 510     Regardless of which method you use to boot to the original firmware, you can
 511     return to Rockbox by pressing and holding \ButtonMenu{} and \ButtonPlay{}
 512     simultaneously until the player hard resets.
 513     }
 514
 515   \opt{h100,h300}
 516     {
 517     Rockbox has a dual-boot feature. To boot into the original firmware,
 518     when the \dap{} is turned off, press and hold the \ButtonRec{} button,
 519     and then press the \ButtonOn{} button.
 520     }
 521
 522   \opt{h10,h10_5gb}
 523     {
 524     Rockbox has a dual-boot feature. It loads the original firmware from
 525     the file \fname{/System/OF.mi4}. To boot into the original firmware,
 526     press and hold the \ButtonLeft{} button while turning on the player.
 527     \note{The iriver firmware does not shut down properly when you turn it off,
 528     it only goes to sleep. To get back into Rockbox when exiting from the
 529     iriver firmware, you will need to reset the player by \opt{h10}{inserting a
 530     pin in the reset hole}\opt{h10_5gb}{removing and reinserting the battery}.}
 531     }
 532
 533   \opt{sansa,sansaAMS}
 534     {
 535     Rockbox has a dual-boot feature. To boot into the original firmware,
 536     press and hold the \ButtonLeft{} button while turning on the player.
 537     }
 538
 539   \opt{sansaAMS}
 540     {
 541     The player will boot into the original firmware if it is powered
 542     by a USB connection. That feature might go away in the future if
 543     Rockbox can handle USB transfers.
 544     }
 545
 546   \opt{mrobe100}
 547     {
 548     Rockbox has a dual-boot feature. It loads the original firmware from
 549     the file \fname{/System/OF.mi4}. To boot into the original firmware,
 550     when the \dap{} is turned off, press the \ButtonPower{} button once and then
 551     a second time when the m:robe bootlogo (the headphone) appears. Hold the
 552     \ButtonPower{} button until you see the ``Loading original firmware...''
 553     message on the screen.
 554     }
 555
 556   \opt{gigabeats}
 557     {
 558     Rockbox has a dual-boot feature. To boot into the original firmware,
 559     turn the \ButtonHold{} switch on just after turning on the \dap{}.
 560     }
 561
 562   }
 563 \subsection{Putting music on your \dap{}}
 564
 565 With the \dap{} connected to the computer as an MSC/UMS device (like a
 566 USB Drive), music files can be put on the player via any standard file
 567 transfer method that you would use to copy files between drives (e.g. Drag 'n' Drop).
 568 The default directory structure that is assumed by some parts of Rockbox
 569 \opt{albumart}{%
 570     (album art searching, and missing-tag fallback in some WPSes) uses the
 571     parent directory of a song as the Album name, and the parent directory of
 572     that folder as the Artist name. While files may be organized however you
 573     like, see \reference{ref:album_art} for the requirements for Album
 574     Art to work properly, and WPSes may display information incorrectly if your
 575     files are not properly tagged, and you have your music organized in a way
 576     different than they assume when attempting to guess the Artist and Album
 577     names from your filetree.
 578 }%
 579 \nopt{albumart}{%
 580     (missing-tag fallback in some WPSes) uses the parent directory of a song
 581     as the Album name, and the parent directory of that folder as the Artist
 582     name. While files may be organized however you like, WPSes may display
 583     information incorrectly if your files are not properly tagged, and you have
 584     your music organized in a way different than they assume when attempting to
 585     guess the Artist and Album names from your filetree.
 586 }
 587 \opt{swcodec}{
 588     See \reference{ref:Supportedaudioformats} for a list of supported audio
 589     formats.
 590 }
 591
 592 \subsection{The first contact}
 593
 594 After you have first started the \dap{}, you'll be presented by the
 595 \setting{Main Menu}. From this menu you can reach every function of Rockbox,
 596 for more information (see \reference{ref:main_menu}). To browse the files
 597 on you \dap{}, select \setting{Files} (see \reference{ref:file_browser}), and to
 598 browse in a view that is based on the meta-data\footnote{ID3 Tags, Vorbis
 599 comments, etc.} of your audio files, select \setting{Database} (see
 600 \reference{ref:database}).
 601
 602 \subsection{Basic controls}
 603 When browsing files and moving through menus you usually get a list view
 604 presented. The navigation in these lists are usually the same and should be
 605 pretty intuitive.
 606 In the tree view use \ActionStdNext{} and \ActionStdPrev{} to move around
 607 the selection. Use \ActionStdOk{} to select an item. When browsing the file
 608 system selecting an audio file plays it. The view switches to the ``While
 609 playing screen'', usually abbreviated as ``WPS'' (see \reference{ref:WPS}. The
 610 dynamic playlist gets replaced with the contents of the current directory. This
 611 way you can easily treat directories as playlists. The created dynamic playlist can
 612 be extended or modified while playing. This is also known as
 613 ``on-the-fly playlist''.
 614 To go back to the \setting{File Browser} stop the playback with the
 615 \ActionWpsStop{} button or return to the file browser while keeping playback
 616 running using \ActionWpsBrowse{}.
 617 In list views you can go back one step with \ActionTreeParentDirectory.
 618
 619 \subsection{Basic concepts}
 620 \subsubsection{Playlists}
 621 Rockbox is playlist oriented. This means that every time you play an audio file,
 622 a so-called ``dynamic playlist'' is generated, unless you play a saved
 623 playlist. You can modify the dynamic playlist while playing and also save
 624 it to a file. If you do not want to use playlists you can simply play your
 625 files directory based.
 626 Playlists are covered in detail in \reference{ref:working_with_playlists}.
 627
 628 \subsubsection{Menu}
 629 From the menu you can customise Rockbox. Rockbox itself is very customisable.
 630 Also there are some special menus for quick access to frequently used
 631 functions.
 632
 633 \subsubsection{Context Menu}
 634 Some views, especially the file browser and the WPS have a context menu.
 635 From the file browser this can be accessed with \ActionStdContext{}.
 636 The contents of the context menu vary, depending on the situation it gets
 637 called. The context menu itself presents you with some operations you can
 638 perform with the currently highlighted file. In the file browser this is
 639 the file (or directory) that is highlighted by the cursor. From the WPS this is
 640 the currently playing file. Also there are some actions that do not apply
 641 to the current file but refer to the screen from which the context menu
 642 gets called. One example is the playback menu, which can be called using
 643 the context menu from within the WPS.
 644
 645 \section{Customising Rockbox}
 646 Rockbox' User Interface can be customised using ``Themes''. Themes usually
 647 only affect the visual appearance, but an advanced user can create a theme
 648 that also changes various other settings like file view, LCD settings and
 649 all other settings that can be modified using \fname{.cfg} files. This topic
 650 is discussed in more detail in \reference{ref:manage_settings}.
 651 The Rockbox distribution comes with some themes that should look nice on
 652 your \dap{}.
 653 \opt{lcd_bitmap}{
 654 \note{Some of the themes shipped with Rockbox need additional
 655 fonts from the fonts package, so make sure you installed them.
 656 Also, if you downloaded additional themes from the Internet make sure you
 657 have the needed fonts installed as otherwise the theme may get displayed
 658 garbled.}
 659 }
 660
 661 \opt{usb_charging}
 662 {
 663     \section{Charging}
 664
 665     The \dap{} can be powered over USB without connecting to your
 666     computer by holding \ActionStdUsbCharge{} while plugging in. This
 667     allows you to continue using the \dap{} normally.
 668 }
 669
 670 \input{rockbox_interface/browsing_and_playing.tex}