4 * The contents of this file are subject to the terms of the
5 * Common Development and Distribution License (the "License").
6 * You may not use this file except in compliance with the License.
8 * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
9 * or http://www.opensolaris.org/os/licensing.
10 * See the License for the specific language governing permissions
11 * and limitations under the License.
13 * When distributing Covered Code, include this CDDL HEADER in each
14 * file and include the License file at usr/src/OPENSOLARIS.LICENSE.
15 * If applicable, add the following below this CDDL HEADER, with the
16 * fields enclosed by brackets "[]" replaced with your own identifying
17 * information: Portions Copyright [yyyy] [name of copyright owner]
21 /* Copyright (c) 1990, 1991 UNIX System Laboratories, Inc. */
22 /* Copyright (c) 1984, 1986, 1987, 1988, 1989, 1990 AT&T */
23 /* All Rights Reserved */
26 * Copyright 2007 Sun Microsystems, Inc. All rights reserved.
27 * Use is subject to license terms.
33 #pragma ident "%Z%%M% %I% %E% SMI"
39 /* Definitions for 8254 Programmable Interrupt Timer ports on AT 386 */
40 #define PITCTR0_PORT 0x40 /* counter 0 port */
41 #define PITCTR1_PORT 0x41 /* counter 1 port */
42 #define PITCTR2_PORT 0x42 /* counter 2 port */
43 #define PITCTL_PORT 0x43 /* PIT control port */
44 #define PITAUX_PORT 0x61 /* PIT auxiliary port */
45 #define SANITY_CTR0 0x48 /* sanity timer counter */
46 #define SANITY_CTL 0x4B /* sanity control word */
47 #define SANITY_CHECK 0x461 /* bit 7 set if sanity timer went off */
48 #define FAILSAFE_NMI 0x80 /* to test if sanity timer went off */
49 #define ENABLE_SANITY 0x04 /* Enables sanity clock NMI ints */
50 #define RESET_SANITY 0x00 /* resets sanity NMI interrupt */
54 #define PITSTAT_OUTPUT 7 /* OUTPUT status bit */
55 #define PITSTAT_NULLCNT 6 /* NULL COUNT status bit */
57 /* Definitions for 8254 commands */
59 #define PIT_READBACK 0xc0 /* read-back command */
60 #define PIT_READBACKC0 0x02 /* enable read-back for counter 0 */
62 /* Following are used for Timer 0 */
63 #define PIT_C0 0x00 /* select counter 0 */
64 #define PIT_LOADMODE 0x30 /* load least significant byte */
65 /* followed by most significant byte */
66 #define PIT_NDIVMODE 0x04 /* divide by N counter */
67 #define PIT_SQUAREMODE 0x06 /* square-wave mode */
68 #define PIT_ENDSIGMODE 0x00 /* assert OUT at end-of-count mode */
70 /* Used for Timer 1. Used for delay calculations in countdown mode */
71 #define PIT_C1 0x40 /* select counter 1 */
72 #define PIT_READMODE 0x30 /* read or load least significant */
73 /* byte followed by most significant */
74 #define PIT_RATEMODE 0x06 /* square-wave mode for USART */
76 #define PIT_C2 0x80 /* select counter 2 */
78 #define SANITY_NUM 0xFFFF /* Sanity timer fires every .2 secs */
79 /* bits used in auxiliary control port for timer 2 */
80 #define PITAUX_GATE2 0x01 /* aux port, PIT gate 2 input */
81 #define PITAUX_OUT2 0x02 /* aux port, PIT clock out 2 enable */
82 #define PIT_HZ 1193182 /* 8254's cycles per second */
88 #endif /* _SYS_PIT_H */