include/configs/ocotea.h

   1 /*
   2  * (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
   3  *
   4  * (C) Copyright 2005
   5  * Stefan Roese, DENX Software Engineering, sr@denx.de.
   6  *
   7  * See file CREDITS for list of people who contributed to this
   8  * project.
   9  *
  10  * This program is free software; you can redistribute it and/or
  11  * modify it under the terms of the GNU General Public License as
  12  * published by the Free Software Foundation; either version 2 of
  13  * the License, or (at your option) any later version.
  14  *
  15  * This program is distributed in the hope that it will be useful,
  16  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  17  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  18  * GNU General Public License for more details.
  19  *
  20  * You should have received a copy of the GNU General Public License
  21  * along with this program; if not, write to the Free Software
  22  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  23  * MA 02111-1307 USA
  24  */
  25
  26 /************************************************************************
  27  * 1 March 2004  Travis B. Sawyer <tsawyer@sandburst.com>
  28  * Adapted to current Das U-Boot source
  29  ***********************************************************************/
  30
  31
  32 /************************************************************************
  33  * OCOTEA.h - configuration for AMCC 440GX Ref (Ocotea)
  34  ***********************************************************************/
  35
  36 #ifndef __CONFIG_H
  37 #define __CONFIG_H
  38
  39 /*-----------------------------------------------------------------------
  40  * High Level Configuration Options
  41  *----------------------------------------------------------------------*/
  42 #define CONFIG_OCOTEA           1           /* Board is ebony           */
  43 #define CONFIG_440GX            1           /* Specifc GX support       */
  44 #define CONFIG_440              1           /* ... PPC440 family        */
  45 #define CONFIG_4xx              1           /* ... PPC4xx family        */
  46 #define CONFIG_BOARD_EARLY_INIT_F 1         /* Call board_pre_init      */
  47 #undef  CFG_DRAM_TEST                       /* Disable-takes long time! */
  48 #define CONFIG_SYS_CLK_FREQ     33333333    /* external freq to pll     */
  49
  50 /*-----------------------------------------------------------------------
  51  * Base addresses -- Note these are effective addresses where the
  52  * actual resources get mapped (not physical addresses)
  53  *----------------------------------------------------------------------*/
  54 #define CFG_SDRAM_BASE      0x00000000      /* _must_ be 0              */
  55 #define CFG_FLASH_BASE      0xff800000      /* start of FLASH           */
  56 #define CFG_MONITOR_BASE    0xfffc0000      /* start of monitor         */
  57 #define CFG_PCI_MEMBASE     0x80000000      /* mapped pci memory        */
  58 #define CFG_PERIPHERAL_BASE 0xe0000000      /* internal peripherals     */
  59 #define CFG_ISRAM_BASE      0xc0000000      /* internal SRAM            */
  60 #define CFG_PCI_BASE        0xd0000000      /* internal PCI regs        */
  61
  62 #define CFG_FPGA_BASE       (CFG_PERIPHERAL_BASE + 0x08300000)
  63 #define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000)
  64
  65 /*-----------------------------------------------------------------------
  66  * Initial RAM & stack pointer (placed in internal SRAM)
  67  *----------------------------------------------------------------------*/
  68 #define CFG_TEMP_STACK_OCM  1
  69 #define CFG_OCM_DATA_ADDR   CFG_ISRAM_BASE
  70 #define CFG_INIT_RAM_ADDR   CFG_ISRAM_BASE  /* Initial RAM address      */
  71 #define CFG_INIT_RAM_END    0x2000          /* End of used area in RAM  */
  72 #define CFG_GBL_DATA_SIZE   128             /* num bytes initial data   */
  73
  74 #define CFG_GBL_DATA_OFFSET     (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
  75 #define CFG_POST_WORD_ADDR      (CFG_GBL_DATA_OFFSET - 0x4)
  76 #define CFG_INIT_SP_OFFSET      CFG_POST_WORD_ADDR
  77
  78 #define CFG_MONITOR_LEN     (256 * 1024)    /* Reserve 256 kB for Mon   */
  79 #define CFG_MALLOC_LEN      (128 * 1024)    /* Reserve 128 kB for malloc*/
  80
  81 /*-----------------------------------------------------------------------
  82  * Serial Port
  83  *----------------------------------------------------------------------*/
  84 #undef  CONFIG_SERIAL_SOFTWARE_FIFO
  85 #define CFG_EXT_SERIAL_CLOCK    (1843200 * 6)   /* Ext clk @ 11.059 MHz */
  86 #define CONFIG_BAUDRATE         115200
  87
  88 #define CFG_BAUDRATE_TABLE  \
  89     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
  90
  91 /*-----------------------------------------------------------------------
  92  * Environment
  93  *----------------------------------------------------------------------*/
  94 /*
  95  * Define here the location of the environment variables (FLASH or NVRAM).
  96  * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
  97  *       supported for backward compatibility.
  98  */
  99 #if 1
 100 #define CFG_ENV_IS_IN_FLASH     1       /* use FLASH for environment vars       */
 101 #else
 102 #define CFG_ENV_IS_IN_NVRAM     1       /* use NVRAM for environment vars       */
 103 #endif
 104
 105
 106 /*-----------------------------------------------------------------------
 107  * NVRAM/RTC
 108  *
 109  * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located.
 110  * The DS1743 code assumes this condition (i.e. -- it assumes the base
 111  * address for the RTC registers is:
 112  *
 113  *      CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE
 114  *
 115  *----------------------------------------------------------------------*/
 116 #define CFG_NVRAM_SIZE      (0x2000 - 8)    /* NVRAM size(8k)- RTC regs */
 117 #define CONFIG_RTC_DS174x       1                   /* DS1743 RTC               */
 118
 119 #ifdef CFG_ENV_IS_IN_NVRAM
 120 #define CFG_ENV_SIZE            0x1000      /* Size of Environment vars */
 121 #define CFG_ENV_ADDR            \
 122         (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)
 123 #endif /* CFG_ENV_IS_IN_NVRAM */
 124
 125 /*-----------------------------------------------------------------------
 126  * FLASH related
 127  *----------------------------------------------------------------------*/
 128 #define CFG_MAX_FLASH_BANKS     3                   /* number of banks      */
 129 #define CFG_MAX_FLASH_SECT      64                  /* sectors per device   */
 130
 131 #undef  CFG_FLASH_CHECKSUM
 132 #define CFG_FLASH_ERASE_TOUT    120000  /* Timeout for Flash Erase (in ms)      */
 133 #define CFG_FLASH_WRITE_TOUT    500     /* Timeout for Flash Write (in ms)      */
 134
 135 #define CFG_FLASH_ADDR0         0x5555
 136 #define CFG_FLASH_ADDR1         0x2aaa
 137 #define CFG_FLASH_WORD_SIZE     unsigned char
 138
 139 #ifdef CFG_ENV_IS_IN_FLASH
 140 #define CFG_ENV_SECT_SIZE       0x10000         /* size of one complete sector  */
 141 #define CFG_ENV_ADDR            (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
 142 #define CFG_ENV_SIZE            0x4000  /* Total Size of Environment Sector     */
 143
 144 /* Address and size of Redundant Environment Sector     */
 145 #define CFG_ENV_ADDR_REDUND     (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
 146 #define CFG_ENV_SIZE_REDUND     (CFG_ENV_SIZE)
 147 #endif /* CFG_ENV_IS_IN_FLASH */
 148
 149 /*-----------------------------------------------------------------------
 150  * DDR SDRAM
 151  *----------------------------------------------------------------------*/
 152 #define CONFIG_SPD_EEPROM       1       /* Use SPD EEPROM for setup     */
 153 #define SPD_EEPROM_ADDRESS {0x53,0x52}  /* SPD i2c spd addresses        */
 154 #define CONFIG_PROG_SDRAM_TLB   1       /* setup SDRAM TLB's dynamically*/
 155
 156 /*-----------------------------------------------------------------------
 157  * I2C
 158  *----------------------------------------------------------------------*/
 159 #define CONFIG_HARD_I2C         1           /* I2C with hardware support        */
 160 #undef  CONFIG_SOFT_I2C                     /* I2C bit-banged           */
 161 #define CFG_I2C_SPEED           400000  /* I2C speed and slave address  */
 162 #define CFG_I2C_SLAVE           0x7F
 163
 164 #define CFG_I2C_MULTI_EEPROMS
 165 #define CFG_I2C_EEPROM_ADDR     (0xa8>>1)
 166 #define CFG_I2C_EEPROM_ADDR_LEN 1
 167 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 168 #define CFG_EEPROM_PAGE_WRITE_BITS 3
 169 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 170
 171 #define CONFIG_PREBOOT  "echo;" \
 172         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 173         "echo"
 174
 175 #undef  CONFIG_BOOTARGS
 176
 177 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 178         "netdev=eth0\0"                                                 \
 179         "hostname=ocotea\0"                                             \
 180         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 181                 "nfsroot=${serverip}:${rootpath}\0"                     \
 182         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 183         "addip=setenv bootargs ${bootargs} "                            \
 184                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 185                 ":${hostname}:${netdev}:off panic=1\0"                  \
 186         "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 187         "flash_nfs=run nfsargs addip addtty;"                           \
 188                 "bootm ${kernel_addr}\0"                                \
 189         "flash_self=run ramargs addip addtty;"                          \
 190                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 191         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 192                 "bootm\0"                                               \
 193         "rootpath=/opt/eldk/ppc_4xx\0"                                  \
 194         "bootfile=/tftpboot/ocotea/uImage\0"                            \
 195         "kernel_addr=fff00000\0"                                        \
 196         "ramdisk_addr=fff10000\0"                                       \
 197         "initrd_high=30000000\0"                                        \
 198         "load=tftp 100000 /tftpboot/ocotea/u-boot.bin\0"                \
 199         "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"   \
 200                 "cp.b 100000 fffc0000 40000;"                           \
 201                 "setenv filesize;saveenv\0"                             \
 202         "upd=run load update\0"                                         \
 203         ""
 204 #define CONFIG_BOOTCOMMAND      "run flash_self"
 205
 206 #if 0
 207 #define CONFIG_BOOTDELAY        -1      /* autoboot disabled            */
 208 #else
 209 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds     */
 210 #endif
 211
 212 #define CONFIG_BAUDRATE         115200
 213
 214 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
 215 #define CFG_LOADS_BAUD_CHANGE   1       /* allow baudrate change        */
 216
 217 #define CONFIG_MII              1       /* MII PHY management           */
 218 #define CONFIG_NET_MULTI        1
 219 #define CONFIG_PHY_ADDR         1       /* PHY address, See schematics  */
 220 #define CONFIG_PHY1_ADDR        2
 221 #define CONFIG_PHY2_ADDR        0x10
 222 #define CONFIG_PHY3_ADDR        0x18
 223 #define CONFIG_HAS_ETH0
 224 #define CONFIG_HAS_ETH1
 225 #define CONFIG_HAS_ETH2
 226 #define CONFIG_HAS_ETH3
 227 #define CONFIG_CIS8201_PHY      1       /* Enable 'special' RGMII mode for Cicada phy */
 228 #define CONFIG_PHY_GIGE         1       /* Include GbE speed/duplex detection */
 229 #define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
 230 #define CONFIG_PHY_RESET_DELAY  1000
 231 #define CFG_RX_ETH_BUFFER       32      /* Number of ethernet rx buffers & descriptors */
 232
 233 #define CONFIG_NETCONSOLE               /* include NetConsole support   */
 234
 235
 236 /*
 237  * BOOTP options
 238  */
 239 #define CONFIG_BOOTP_BOOTFILESIZE
 240 #define CONFIG_BOOTP_BOOTPATH
 241 #define CONFIG_BOOTP_GATEWAY
 242 #define CONFIG_BOOTP_HOSTNAME
 243
 244
 245 /*
 246  * Command line configuration.
 247  */
 248 #include <config_cmd_default.h>
 249
 250 #define CONFIG_CMD_ASKENV
 251 #define CONFIG_CMD_DATE
 252 #define CONFIG_CMD_DHCP
 253 #define CONFIG_CMD_DIAG
 254 #define CONFIG_CMD_ELF
 255 #define CONFIG_CMD_EEPROM
 256 #define CONFIG_CMD_I2C
 257 #define CONFIG_CMD_IRQ
 258 #define CONFIG_CMD_MII
 259 #define CONFIG_CMD_NET
 260 #define CONFIG_CMD_NFS
 261 #define CONFIG_CMD_PCI
 262 #define CONFIG_CMD_PING
 263 #define CONFIG_CMD_REGINFO
 264 #define CONFIG_CMD_SDRAM
 265 #define CONFIG_CMD_SNTP
 266
 267
 268 #undef CONFIG_WATCHDOG                  /* watchdog disabled            */
 269
 270 /*
 271  * Miscellaneous configurable options
 272  */
 273 #define CFG_LONGHELP                    /* undef to save memory         */
 274 #define CFG_PROMPT      "=> "           /* Monitor Command Prompt       */
 275 #if defined(CONFIG_CMD_KGDB)
 276 #define CFG_CBSIZE      1024            /* Console I/O Buffer Size      */
 277 #else
 278 #define CFG_CBSIZE      256             /* Console I/O Buffer Size      */
 279 #endif
 280 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 281 #define CFG_MAXARGS     16              /* max number of command args   */
 282 #define CFG_BARGSIZE    CFG_CBSIZE      /* Boot Argument Buffer Size    */
 283
 284 #define CFG_MEMTEST_START       0x0400000       /* memtest works on     */
 285 #define CFG_MEMTEST_END         0x0C00000       /* 4 ... 12 MB in DRAM  */
 286
 287 #define CFG_LOAD_ADDR           0x100000        /* default load address */
 288 #define CFG_EXTBDINFO           1       /* To use extended board_into (bd_t) */
 289
 290 #define CFG_HZ                  1000    /* decrementer freq: 1 ms ticks */
 291
 292 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 293 #define CONFIG_LOOPW            1       /* enable loopw command         */
 294 #define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
 295 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 296 #define CONFIG_VERSION_VARIABLE 1       /* include version env variable */
 297
 298 /*-----------------------------------------------------------------------
 299  * PCI stuff
 300  *-----------------------------------------------------------------------
 301  */
 302 /* General PCI */
 303 #define CONFIG_PCI                      /* include pci support          */
 304 #define CONFIG_PCI_PNP                  /* do pci plug-and-play         */
 305 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
 306 #define CFG_PCI_TARGBASE    0x80000000  /* PCIaddr mapped to CFG_PCI_MEMBASE */
 307
 308 /* Board-specific PCI */
 309 #define CFG_PCI_TARGET_INIT             /* let board init pci target    */
 310
 311 #define CFG_PCI_SUBSYS_VENDORID 0x10e8  /* AMCC */
 312 #define CFG_PCI_SUBSYS_DEVICEID 0xcafe  /* Whatever */
 313
 314 /*
 315  * For booting Linux, the board info and command line data
 316  * have to be in the first 8 MB of memory, since this is
 317  * the maximum mapped by the Linux kernel during initialization.
 318  */
 319 #define CFG_BOOTMAPSZ           (8 << 20)       /* Initial Memory map for Linux */
 320
 321 /*
 322  * Internal Definitions
 323  *
 324  * Boot Flags
 325  */
 326 #define BOOTFLAG_COLD   0x01            /* Normal Power-On: Boot from FLASH     */
 327 #define BOOTFLAG_WARM   0x02            /* Software reboot                      */
 328
 329 #if defined(CONFIG_CMD_KGDB)
 330 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 331 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 332 #endif
 333 #endif  /* __CONFIG_H */