release/src-rt-6.x.4708/linux/linux-2.6.36/drivers/usb/serial/whiteheat.h

   1 /*
   2  * USB ConnectTech WhiteHEAT driver
   3  *
   4  *      Copyright (C) 2002
   5  *          Connect Tech Inc.
   6  *
   7  *      Copyright (C) 1999, 2000
   8  *          Greg Kroah-Hartman (greg@kroah.com)
   9  *
  10  *      This program is free software; you can redistribute it and/or modify
  11  *      it under the terms of the GNU General Public License as published by
  12  *      the Free Software Foundation; either version 2 of the License, or
  13  *      (at your option) any later version.
  14  *
  15  * See Documentation/usb/usb-serial.txt for more information on using this
  16  * driver
  17  *
  18  */
  19
  20 #ifndef __LINUX_USB_SERIAL_WHITEHEAT_H
  21 #define __LINUX_USB_SERIAL_WHITEHEAT_H
  22
  23
  24 /* WhiteHEAT commands */
  25 #define WHITEHEAT_OPEN                  1       /* open the port */
  26 #define WHITEHEAT_CLOSE                 2       /* close the port */
  27 #define WHITEHEAT_SETUP_PORT            3       /* change port settings */
  28 #define WHITEHEAT_SET_RTS               4       /* turn RTS on or off */
  29 #define WHITEHEAT_SET_DTR               5       /* turn DTR on or off */
  30 #define WHITEHEAT_SET_BREAK             6       /* turn BREAK on or off */
  31 #define WHITEHEAT_DUMP                  7       /* dump memory */
  32 #define WHITEHEAT_STATUS                8       /* get status */
  33 #define WHITEHEAT_PURGE                 9       /* clear the UART fifos */
  34 #define WHITEHEAT_GET_DTR_RTS           10      /* get the state of DTR and RTS
  35                                                         for a port */
  36 #define WHITEHEAT_GET_HW_INFO           11      /* get EEPROM info and
  37                                                         hardware ID */
  38 #define WHITEHEAT_REPORT_TX_DONE        12      /* get the next TX done */
  39 #define WHITEHEAT_EVENT                 13      /* unsolicited status events */
  40 #define WHITEHEAT_ECHO                  14      /* send data to the indicated
  41                                                    IN endpoint */
  42 #define WHITEHEAT_DO_TEST               15      /* perform specified test */
  43 #define WHITEHEAT_CMD_COMPLETE          16      /* reply for some commands */
  44 #define WHITEHEAT_CMD_FAILURE           17      /* reply for failed commands */
  45
  46
  47 /*
  48  * Commands to the firmware
  49  */
  50
  51
  52 /*
  53  * WHITEHEAT_OPEN
  54  * WHITEHEAT_CLOSE
  55  * WHITEHEAT_STATUS
  56  * WHITEHEAT_GET_DTR_RTS
  57  * WHITEHEAT_REPORT_TX_DONE
  58 */
  59 struct whiteheat_simple {
  60         __u8    port;   /* port number (1 to N) */
  61 };
  62
  63
  64 /*
  65  * WHITEHEAT_SETUP_PORT
  66  */
  67 #define WHITEHEAT_PAR_NONE      'n'     /* no parity */
  68 #define WHITEHEAT_PAR_EVEN      'e'     /* even parity */
  69 #define WHITEHEAT_PAR_ODD       'o'     /* odd parity */
  70 #define WHITEHEAT_PAR_SPACE     '0'     /* space (force 0) parity */
  71 #define WHITEHEAT_PAR_MARK      '1'     /* mark (force 1) parity */
  72
  73 #define WHITEHEAT_SFLOW_NONE    'n'     /* no software flow control */
  74 #define WHITEHEAT_SFLOW_RX      'r'     /* XOFF/ON is sent when RX
  75                                            fills/empties */
  76 #define WHITEHEAT_SFLOW_TX      't'     /* when received XOFF/ON will
  77                                            stop/start TX */
  78 #define WHITEHEAT_SFLOW_RXTX    'b'     /* both SFLOW_RX and SFLOW_TX */
  79
  80 #define WHITEHEAT_HFLOW_NONE            0x00    /* no hardware flow control */
  81 #define WHITEHEAT_HFLOW_RTS_TOGGLE      0x01    /* RTS is on during transmit,
  82                                                    off otherwise */
  83 #define WHITEHEAT_HFLOW_DTR             0x02    /* DTR is off/on when RX
  84                                                    fills/empties */
  85 #define WHITEHEAT_HFLOW_CTS             0x08    /* when received CTS off/on
  86                                                    will stop/start TX */
  87 #define WHITEHEAT_HFLOW_DSR             0x10    /* when received DSR off/on
  88                                                    will stop/start TX */
  89 #define WHITEHEAT_HFLOW_RTS             0x80    /* RTS is off/on when RX
  90                                                    fills/empties */
  91
  92 struct whiteheat_port_settings {
  93         __u8    port;           /* port number (1 to N) */
  94         __u32   baud;           /* any value 7 - 460800, firmware calculates
  95                                    best fit; arrives little endian */
  96         __u8    bits;           /* 5, 6, 7, or 8 */
  97         __u8    stop;           /* 1 or 2, default 1 (2 = 1.5 if bits = 5) */
  98         __u8    parity;         /* see WHITEHEAT_PAR_* above */
  99         __u8    sflow;          /* see WHITEHEAT_SFLOW_* above */
 100         __u8    xoff;           /* XOFF byte value */
 101         __u8    xon;            /* XON byte value */
 102         __u8    hflow;          /* see WHITEHEAT_HFLOW_* above */
 103         __u8    lloop;          /* 0/1 turns local loopback mode off/on */
 104 } __attribute__ ((packed));
 105
 106
 107 /*
 108  * WHITEHEAT_SET_RTS
 109  * WHITEHEAT_SET_DTR
 110  * WHITEHEAT_SET_BREAK
 111  */
 112 #define WHITEHEAT_RTS_OFF       0x00
 113 #define WHITEHEAT_RTS_ON        0x01
 114 #define WHITEHEAT_DTR_OFF       0x00
 115 #define WHITEHEAT_DTR_ON        0x01
 116 #define WHITEHEAT_BREAK_OFF     0x00
 117 #define WHITEHEAT_BREAK_ON      0x01
 118
 119 struct whiteheat_set_rdb {
 120         __u8    port;           /* port number (1 to N) */
 121         __u8    state;          /* 0/1 turns signal off/on */
 122 };
 123
 124
 125 /*
 126  * WHITEHEAT_DUMP
 127  */
 128 #define WHITEHEAT_DUMP_MEM_DATA         'd'  /* data */
 129 #define WHITEHEAT_DUMP_MEM_IDATA        'i'  /* idata */
 130 #define WHITEHEAT_DUMP_MEM_BDATA        'b'  /* bdata */
 131 #define WHITEHEAT_DUMP_MEM_XDATA        'x'  /* xdata */
 132
 133 /*
 134  * Allowable address ranges (firmware checks address):
 135  * Type DATA:  0x00 - 0xff
 136  * Type IDATA: 0x80 - 0xff
 137  * Type BDATA: 0x20 - 0x2f
 138  * Type XDATA: 0x0000 - 0xffff
 139  *
 140  * B/I/DATA all read the local memory space
 141  * XDATA reads the external memory space
 142  * BDATA returns bits as bytes
 143  *
 144  * NOTE: 0x80 - 0xff (local space) are the Special Function Registers
 145  *       of the 8051, and some have on-read side-effects.
 146  */
 147
 148 struct whiteheat_dump {
 149         __u8    mem_type;       /* see WHITEHEAT_DUMP_* above */
 150         __u16   addr;           /* address, see restrictions above */
 151         __u16   length;         /* number of bytes to dump, max 63 bytes */
 152 };
 153
 154
 155 /*
 156  * WHITEHEAT_PURGE
 157  */
 158 #define WHITEHEAT_PURGE_RX      0x01    /* purge rx fifos */
 159 #define WHITEHEAT_PURGE_TX      0x02    /* purge tx fifos */
 160
 161 struct whiteheat_purge {
 162         __u8    port;           /* port number (1 to N) */
 163         __u8    what;           /* bit pattern of what to purge */
 164 };
 165
 166
 167 /*
 168  * WHITEHEAT_ECHO
 169  */
 170 struct whiteheat_echo {
 171         __u8    port;           /* port number (1 to N) */
 172         __u8    length;         /* length of message to echo, max 61 bytes */
 173         __u8    echo_data[61];  /* data to echo */
 174 };
 175
 176
 177 /*
 178  * WHITEHEAT_DO_TEST
 179  */
 180 #define WHITEHEAT_TEST_UART_RW          0x01  /* read/write uart registers */
 181 #define WHITEHEAT_TEST_UART_INTR        0x02  /* uart interrupt */
 182 #define WHITEHEAT_TEST_SETUP_CONT       0x03  /* setup for
 183                                                 PORT_CONT/PORT_DISCONT */
 184 #define WHITEHEAT_TEST_PORT_CONT        0x04  /* port connect */
 185 #define WHITEHEAT_TEST_PORT_DISCONT     0x05  /* port disconnect */
 186 #define WHITEHEAT_TEST_UART_CLK_START   0x06  /* uart clock test start */
 187 #define WHITEHEAT_TEST_UART_CLK_STOP    0x07  /* uart clock test stop */
 188 #define WHITEHEAT_TEST_MODEM_FT         0x08  /* modem signals, requires a
 189                                                 loopback cable/connector */
 190 #define WHITEHEAT_TEST_ERASE_EEPROM     0x09  /* erase eeprom */
 191 #define WHITEHEAT_TEST_READ_EEPROM      0x0a  /* read eeprom */
 192 #define WHITEHEAT_TEST_PROGRAM_EEPROM   0x0b  /* program eeprom */
 193
 194 struct whiteheat_test {
 195         __u8    port;           /* port number (1 to n) */
 196         __u8    test;           /* see WHITEHEAT_TEST_* above*/
 197         __u8    info[32];       /* additional info */
 198 };
 199
 200
 201 /*
 202  * Replies from the firmware
 203  */
 204
 205
 206 /*
 207  * WHITEHEAT_STATUS
 208  */
 209 #define WHITEHEAT_EVENT_MODEM           0x01    /* modem field is valid */
 210 #define WHITEHEAT_EVENT_ERROR           0x02    /* error field is valid */
 211 #define WHITEHEAT_EVENT_FLOW            0x04    /* flow field is valid */
 212 #define WHITEHEAT_EVENT_CONNECT         0x08    /* connect field is valid */
 213
 214 #define WHITEHEAT_FLOW_NONE             0x00    /* no flow control active */
 215 #define WHITEHEAT_FLOW_HARD_OUT         0x01    /* TX is stopped by CTS
 216                                                   (waiting for CTS to go on) */
 217 #define WHITEHEAT_FLOW_HARD_IN          0x02    /* remote TX is stopped
 218                                                   by RTS */
 219 #define WHITEHEAT_FLOW_SOFT_OUT         0x04    /* TX is stopped by XOFF
 220                                                   received (waiting for XON) */
 221 #define WHITEHEAT_FLOW_SOFT_IN          0x08    /* remote TX is stopped by XOFF
 222                                                   transmitted */
 223 #define WHITEHEAT_FLOW_TX_DONE          0x80    /* TX has completed */
 224
 225 struct whiteheat_status_info {
 226         __u8    port;           /* port number (1 to N) */
 227         __u8    event;          /* indicates what the current event is,
 228                                         see WHITEHEAT_EVENT_* above */
 229         __u8    modem;          /* modem signal status (copy of uart's
 230                                         MSR register) */
 231         __u8    error;          /* line status (copy of uart's LSR register) */
 232         __u8    flow;           /* flow control state, see WHITEHEAT_FLOW_*
 233                                         above */
 234         __u8    connect;        /* 0 means not connected, non-zero means
 235                                         connected */
 236 };
 237
 238
 239 /*
 240  * WHITEHEAT_GET_DTR_RTS
 241  */
 242 struct whiteheat_dr_info {
 243         __u8    mcr;            /* copy of uart's MCR register */
 244 };
 245
 246
 247 /*
 248  * WHITEHEAT_GET_HW_INFO
 249  */
 250 struct whiteheat_hw_info {
 251         __u8    hw_id;          /* hardware id number, WhiteHEAT = 0 */
 252         __u8    sw_major_rev;   /* major version number */
 253         __u8    sw_minor_rev;   /* minor version number */
 254         struct whiteheat_hw_eeprom_info {
 255                 __u8    b0;                     /* B0 */
 256                 __u8    vendor_id_low;          /* vendor id (low byte) */
 257                 __u8    vendor_id_high;         /* vendor id (high byte) */
 258                 __u8    product_id_low;         /* product id (low byte) */
 259                 __u8    product_id_high;        /* product id (high byte) */
 260                 __u8    device_id_low;          /* device id (low byte) */
 261                 __u8    device_id_high;         /* device id (high byte) */
 262                 __u8    not_used_1;
 263                 __u8    serial_number_0;        /* serial number (low byte) */
 264                 __u8    serial_number_1;        /* serial number */
 265                 __u8    serial_number_2;        /* serial number */
 266                 __u8    serial_number_3;        /* serial number (high byte) */
 267                 __u8    not_used_2;
 268                 __u8    not_used_3;
 269                 __u8    checksum_low;           /* checksum (low byte) */
 270                 __u8    checksum_high;          /* checksum (high byte */
 271         } hw_eeprom_info;       /* EEPROM contents */
 272 };
 273
 274
 275 /*
 276  * WHITEHEAT_EVENT
 277  */
 278 struct whiteheat_event_info {
 279         __u8    port;           /* port number (1 to N) */
 280         __u8    event;          /* see whiteheat_status_info.event */
 281         __u8    info;           /* see whiteheat_status_info.modem, .error,
 282                                         .flow, .connect */
 283 };
 284
 285
 286 /*
 287  * WHITEHEAT_DO_TEST
 288  */
 289 #define WHITEHEAT_TEST_FAIL     0x00  /* test failed */
 290 #define WHITEHEAT_TEST_UNKNOWN  0x01  /* unknown test requested */
 291 #define WHITEHEAT_TEST_PASS     0xff  /* test passed */
 292
 293 struct whiteheat_test_info {
 294         __u8    port;           /* port number (1 to N) */
 295         __u8    test;           /* indicates which test this is a response for,
 296                                    see WHITEHEAT_DO_TEST above */
 297         __u8    status;         /* see WHITEHEAT_TEST_* above */
 298         __u8    results[32];    /* test-dependent results */
 299 };
 300
 301
 302 #endif