GUI: Fix Tomato RAF theme for all builds. Compilation typo.
[tomato.git] / release / src-rt-6.x.4708 / linux / linux-2.6.36 / arch / arm / mach-pxa / lubbock.c
blob330c3282856e620ec879563e16655c6d56d6d2a9
1 /*
2 * linux/arch/arm/mach-pxa/lubbock.c
4 * Support for the Intel DBPXA250 Development Platform.
6 * Author: Nicolas Pitre
7 * Created: Jun 15, 2001
8 * Copyright: MontaVista Software Inc.
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License version 2 as
12 * published by the Free Software Foundation.
14 #include <linux/module.h>
15 #include <linux/kernel.h>
16 #include <linux/init.h>
17 #include <linux/platform_device.h>
18 #include <linux/sysdev.h>
19 #include <linux/major.h>
20 #include <linux/fb.h>
21 #include <linux/interrupt.h>
22 #include <linux/mtd/mtd.h>
23 #include <linux/mtd/partitions.h>
24 #include <linux/smc91x.h>
26 #include <linux/spi/spi.h>
27 #include <linux/spi/ads7846.h>
28 #include <mach/pxa2xx_spi.h>
30 #include <asm/setup.h>
31 #include <asm/memory.h>
32 #include <asm/mach-types.h>
33 #include <mach/hardware.h>
34 #include <asm/irq.h>
35 #include <asm/sizes.h>
37 #include <asm/mach/arch.h>
38 #include <asm/mach/map.h>
39 #include <asm/mach/irq.h>
40 #include <asm/mach/flash.h>
42 #include <asm/hardware/sa1111.h>
44 #include <mach/pxa25x.h>
45 #include <mach/gpio.h>
46 #include <mach/audio.h>
47 #include <mach/lubbock.h>
48 #include <mach/udc.h>
49 #include <mach/irda.h>
50 #include <mach/pxafb.h>
51 #include <mach/mmc.h>
52 #include <mach/pm.h>
54 #include "generic.h"
55 #include "clock.h"
56 #include "devices.h"
58 static unsigned long lubbock_pin_config[] __initdata = {
59 GPIO15_nCS_1, /* CS1 - Flash */
60 GPIO78_nCS_2, /* CS2 - Baseboard FGPA */
61 GPIO79_nCS_3, /* CS3 - SMC ethernet */
62 GPIO80_nCS_4, /* CS4 - SA1111 */
64 /* SSP data pins */
65 GPIO23_SSP1_SCLK,
66 GPIO25_SSP1_TXD,
67 GPIO26_SSP1_RXD,
69 /* AC97 */
70 GPIO28_AC97_BITCLK,
71 GPIO29_AC97_SDATA_IN_0,
72 GPIO30_AC97_SDATA_OUT,
73 GPIO31_AC97_SYNC,
75 /* LCD - 16bpp DSTN */
76 GPIOxx_LCD_DSTN_16BPP,
78 /* BTUART */
79 GPIO42_BTUART_RXD,
80 GPIO43_BTUART_TXD,
81 GPIO44_BTUART_CTS,
82 GPIO45_BTUART_RTS,
84 /* PC Card */
85 GPIO48_nPOE,
86 GPIO49_nPWE,
87 GPIO50_nPIOR,
88 GPIO51_nPIOW,
89 GPIO52_nPCE_1,
90 GPIO53_nPCE_2,
91 GPIO54_nPSKTSEL,
92 GPIO55_nPREG,
93 GPIO56_nPWAIT,
94 GPIO57_nIOIS16,
96 /* MMC */
97 GPIO6_MMC_CLK,
98 GPIO8_MMC_CS0,
100 /* wakeup */
101 GPIO1_GPIO | WAKEUP_ON_EDGE_RISE,
104 #define LUB_HEXLED __LUB_REG(LUBBOCK_FPGA_PHYS + 0x010)
105 #define LUB_MISC_WR __LUB_REG(LUBBOCK_FPGA_PHYS + 0x080)
107 void lubbock_set_hexled(uint32_t value)
109 LUB_HEXLED = value;
112 void lubbock_set_misc_wr(unsigned int mask, unsigned int set)
114 unsigned long flags;
116 local_irq_save(flags);
117 LUB_MISC_WR = (LUB_MISC_WR & ~mask) | (set & mask);
118 local_irq_restore(flags);
120 EXPORT_SYMBOL(lubbock_set_misc_wr);
122 static unsigned long lubbock_irq_enabled;
124 static void lubbock_mask_irq(unsigned int irq)
126 int lubbock_irq = (irq - LUBBOCK_IRQ(0));
127 LUB_IRQ_MASK_EN = (lubbock_irq_enabled &= ~(1 << lubbock_irq));
130 static void lubbock_unmask_irq(unsigned int irq)
132 int lubbock_irq = (irq - LUBBOCK_IRQ(0));
133 /* the irq can be acknowledged only if deasserted, so it's done here */
134 LUB_IRQ_SET_CLR &= ~(1 << lubbock_irq);
135 LUB_IRQ_MASK_EN = (lubbock_irq_enabled |= (1 << lubbock_irq));
138 static struct irq_chip lubbock_irq_chip = {
139 .name = "FPGA",
140 .ack = lubbock_mask_irq,
141 .mask = lubbock_mask_irq,
142 .unmask = lubbock_unmask_irq,
145 static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc)
147 unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
148 do {
149 desc->chip->ack(irq); /* clear our parent irq */
150 if (likely(pending)) {
151 irq = LUBBOCK_IRQ(0) + __ffs(pending);
152 generic_handle_irq(irq);
154 pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
155 } while (pending);
158 static void __init lubbock_init_irq(void)
160 int irq;
162 pxa25x_init_irq();
164 /* setup extra lubbock irqs */
165 for (irq = LUBBOCK_IRQ(0); irq <= LUBBOCK_LAST_IRQ; irq++) {
166 set_irq_chip(irq, &lubbock_irq_chip);
167 set_irq_handler(irq, handle_level_irq);
168 set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
171 set_irq_chained_handler(IRQ_GPIO(0), lubbock_irq_handler);
172 set_irq_type(IRQ_GPIO(0), IRQ_TYPE_EDGE_FALLING);
175 #ifdef CONFIG_PM
177 static int lubbock_irq_resume(struct sys_device *dev)
179 LUB_IRQ_MASK_EN = lubbock_irq_enabled;
180 return 0;
183 static struct sysdev_class lubbock_irq_sysclass = {
184 .name = "cpld_irq",
185 .resume = lubbock_irq_resume,
188 static struct sys_device lubbock_irq_device = {
189 .cls = &lubbock_irq_sysclass,
192 static int __init lubbock_irq_device_init(void)
194 int ret = -ENODEV;
196 if (machine_is_lubbock()) {
197 ret = sysdev_class_register(&lubbock_irq_sysclass);
198 if (ret == 0)
199 ret = sysdev_register(&lubbock_irq_device);
201 return ret;
204 device_initcall(lubbock_irq_device_init);
206 #endif
208 static int lubbock_udc_is_connected(void)
210 return (LUB_MISC_RD & (1 << 9)) == 0;
213 static struct pxa2xx_udc_mach_info udc_info __initdata = {
214 .udc_is_connected = lubbock_udc_is_connected,
215 // no D+ pullup; lubbock can't connect/disconnect in software
218 static struct resource sa1111_resources[] = {
219 [0] = {
220 .start = 0x10000000,
221 .end = 0x10001fff,
222 .flags = IORESOURCE_MEM,
224 [1] = {
225 .start = LUBBOCK_SA1111_IRQ,
226 .end = LUBBOCK_SA1111_IRQ,
227 .flags = IORESOURCE_IRQ,
231 static struct sa1111_platform_data sa1111_info = {
232 .irq_base = IRQ_BOARD_END,
235 static struct platform_device sa1111_device = {
236 .name = "sa1111",
237 .id = -1,
238 .num_resources = ARRAY_SIZE(sa1111_resources),
239 .resource = sa1111_resources,
240 .dev = {
241 .platform_data = &sa1111_info,
245 /* ADS7846 is connected through SSP ... and if your board has J5 populated,
246 * you can select it to replace the ucb1400 by switching the touchscreen cable
247 * (to J5) and poking board registers (as done below). Else it's only useful
248 * for the temperature sensors.
250 static struct pxa2xx_spi_master pxa_ssp_master_info = {
251 .num_chipselect = 1,
254 static int lubbock_ads7846_pendown_state(void)
256 /* TS_BUSY is bit 8 in LUB_MISC_RD, but pendown is irq-only */
257 return 0;
260 static struct ads7846_platform_data ads_info = {
261 .model = 7846,
262 .vref_delay_usecs = 100, /* internal, no cap */
263 .get_pendown_state = lubbock_ads7846_pendown_state,
264 // .x_plate_ohms = 500, /* GUESS! */
265 // .y_plate_ohms = 500, /* GUESS! */
268 static void ads7846_cs(u32 command)
270 static const unsigned TS_nCS = 1 << 11;
271 lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS);
274 static struct pxa2xx_spi_chip ads_hw = {
275 .tx_threshold = 1,
276 .rx_threshold = 2,
277 .cs_control = ads7846_cs,
280 static struct spi_board_info spi_board_info[] __initdata = { {
281 .modalias = "ads7846",
282 .platform_data = &ads_info,
283 .controller_data = &ads_hw,
284 .irq = LUBBOCK_BB_IRQ,
285 .max_speed_hz = 120000 /* max sample rate at 3V */
286 * 26 /* command + data + overhead */,
287 .bus_num = 1,
288 .chip_select = 0,
292 static struct resource smc91x_resources[] = {
293 [0] = {
294 .name = "smc91x-regs",
295 .start = 0x0c000c00,
296 .end = 0x0c0fffff,
297 .flags = IORESOURCE_MEM,
299 [1] = {
300 .start = LUBBOCK_ETH_IRQ,
301 .end = LUBBOCK_ETH_IRQ,
302 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
304 [2] = {
305 .name = "smc91x-attrib",
306 .start = 0x0e000000,
307 .end = 0x0e0fffff,
308 .flags = IORESOURCE_MEM,
312 static struct smc91x_platdata lubbock_smc91x_info = {
313 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_IO_SHIFT_2,
316 static struct platform_device smc91x_device = {
317 .name = "smc91x",
318 .id = -1,
319 .num_resources = ARRAY_SIZE(smc91x_resources),
320 .resource = smc91x_resources,
321 .dev = {
322 .platform_data = &lubbock_smc91x_info,
326 static struct resource flash_resources[] = {
327 [0] = {
328 .start = 0x00000000,
329 .end = SZ_64M - 1,
330 .flags = IORESOURCE_MEM,
332 [1] = {
333 .start = 0x04000000,
334 .end = 0x04000000 + SZ_64M - 1,
335 .flags = IORESOURCE_MEM,
339 static struct mtd_partition lubbock_partitions[] = {
341 .name = "Bootloader",
342 .size = 0x00040000,
343 .offset = 0,
344 .mask_flags = MTD_WRITEABLE /* force read-only */
346 .name = "Kernel",
347 .size = 0x00100000,
348 .offset = 0x00040000,
350 .name = "Filesystem",
351 .size = MTDPART_SIZ_FULL,
352 .offset = 0x00140000
356 static struct flash_platform_data lubbock_flash_data[2] = {
358 .map_name = "cfi_probe",
359 .parts = lubbock_partitions,
360 .nr_parts = ARRAY_SIZE(lubbock_partitions),
361 }, {
362 .map_name = "cfi_probe",
363 .parts = NULL,
364 .nr_parts = 0,
368 static struct platform_device lubbock_flash_device[2] = {
370 .name = "pxa2xx-flash",
371 .id = 0,
372 .dev = {
373 .platform_data = &lubbock_flash_data[0],
375 .resource = &flash_resources[0],
376 .num_resources = 1,
379 .name = "pxa2xx-flash",
380 .id = 1,
381 .dev = {
382 .platform_data = &lubbock_flash_data[1],
384 .resource = &flash_resources[1],
385 .num_resources = 1,
389 static struct platform_device *devices[] __initdata = {
390 &sa1111_device,
391 &smc91x_device,
392 &lubbock_flash_device[0],
393 &lubbock_flash_device[1],
396 static struct pxafb_mode_info sharp_lm8v31_mode = {
397 .pixclock = 270000,
398 .xres = 640,
399 .yres = 480,
400 .bpp = 16,
401 .hsync_len = 1,
402 .left_margin = 3,
403 .right_margin = 3,
404 .vsync_len = 1,
405 .upper_margin = 0,
406 .lower_margin = 0,
407 .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
408 .cmap_greyscale = 0,
411 static struct pxafb_mach_info sharp_lm8v31 = {
412 .modes = &sharp_lm8v31_mode,
413 .num_modes = 1,
414 .cmap_inverse = 0,
415 .cmap_static = 0,
416 .lcd_conn = LCD_COLOR_DSTN_16BPP | LCD_PCLK_EDGE_FALL |
417 LCD_AC_BIAS_FREQ(255),
420 #define MMC_POLL_RATE msecs_to_jiffies(1000)
422 static void lubbock_mmc_poll(unsigned long);
423 static irq_handler_t mmc_detect_int;
425 static struct timer_list mmc_timer = {
426 .function = lubbock_mmc_poll,
429 static void lubbock_mmc_poll(unsigned long data)
431 unsigned long flags;
433 /* clear any previous irq state, then ... */
434 local_irq_save(flags);
435 LUB_IRQ_SET_CLR &= ~(1 << 0);
436 local_irq_restore(flags);
438 /* poll until mmc/sd card is removed */
439 if (LUB_IRQ_SET_CLR & (1 << 0))
440 mod_timer(&mmc_timer, jiffies + MMC_POLL_RATE);
441 else {
442 (void) mmc_detect_int(LUBBOCK_SD_IRQ, (void *)data);
443 enable_irq(LUBBOCK_SD_IRQ);
447 static irqreturn_t lubbock_detect_int(int irq, void *data)
449 /* IRQ is level triggered; disable, and poll for removal */
450 disable_irq(irq);
451 mod_timer(&mmc_timer, jiffies + MMC_POLL_RATE);
453 return mmc_detect_int(irq, data);
456 static int lubbock_mci_init(struct device *dev,
457 irq_handler_t detect_int,
458 void *data)
460 /* detect card insert/eject */
461 mmc_detect_int = detect_int;
462 init_timer(&mmc_timer);
463 mmc_timer.data = (unsigned long) data;
464 return request_irq(LUBBOCK_SD_IRQ, lubbock_detect_int,
465 IRQF_SAMPLE_RANDOM, "lubbock-sd-detect", data);
468 static int lubbock_mci_get_ro(struct device *dev)
470 return (LUB_MISC_RD & (1 << 2)) != 0;
473 static void lubbock_mci_exit(struct device *dev, void *data)
475 free_irq(LUBBOCK_SD_IRQ, data);
476 del_timer_sync(&mmc_timer);
479 static struct pxamci_platform_data lubbock_mci_platform_data = {
480 .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
481 .detect_delay_ms = 10,
482 .init = lubbock_mci_init,
483 .get_ro = lubbock_mci_get_ro,
484 .exit = lubbock_mci_exit,
485 .gpio_card_detect = -1,
486 .gpio_card_ro = -1,
487 .gpio_power = -1,
490 static void lubbock_irda_transceiver_mode(struct device *dev, int mode)
492 unsigned long flags;
494 local_irq_save(flags);
495 if (mode & IR_SIRMODE) {
496 LUB_MISC_WR &= ~(1 << 4);
497 } else if (mode & IR_FIRMODE) {
498 LUB_MISC_WR |= 1 << 4;
500 pxa2xx_transceiver_mode(dev, mode);
501 local_irq_restore(flags);
504 static struct pxaficp_platform_data lubbock_ficp_platform_data = {
505 .gpio_pwdown = -1,
506 .transceiver_cap = IR_SIRMODE | IR_FIRMODE,
507 .transceiver_mode = lubbock_irda_transceiver_mode,
510 static void __init lubbock_init(void)
512 int flashboot = (LUB_CONF_SWITCHES & 1);
514 pxa2xx_mfp_config(ARRAY_AND_SIZE(lubbock_pin_config));
516 pxa_set_ffuart_info(NULL);
517 pxa_set_btuart_info(NULL);
518 pxa_set_stuart_info(NULL);
520 clk_add_alias("SA1111_CLK", NULL, "GPIO11_CLK", NULL);
521 pxa_set_udc_info(&udc_info);
522 set_pxa_fb_info(&sharp_lm8v31);
523 pxa_set_mci_info(&lubbock_mci_platform_data);
524 pxa_set_ficp_info(&lubbock_ficp_platform_data);
525 pxa_set_ac97_info(NULL);
527 lubbock_flash_data[0].width = lubbock_flash_data[1].width =
528 (BOOT_DEF & 1) ? 2 : 4;
529 /* Compensate for the nROMBT switch which swaps the flash banks */
530 printk(KERN_NOTICE "Lubbock configured to boot from %s (bank %d)\n",
531 flashboot?"Flash":"ROM", flashboot);
533 lubbock_flash_data[flashboot^1].name = "application-flash";
534 lubbock_flash_data[flashboot].name = "boot-rom";
535 (void) platform_add_devices(devices, ARRAY_SIZE(devices));
537 pxa2xx_set_spi_info(1, &pxa_ssp_master_info);
538 spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
541 static struct map_desc lubbock_io_desc[] __initdata = {
542 { /* CPLD */
543 .virtual = LUBBOCK_FPGA_VIRT,
544 .pfn = __phys_to_pfn(LUBBOCK_FPGA_PHYS),
545 .length = 0x00100000,
546 .type = MT_DEVICE
550 static void __init lubbock_map_io(void)
552 pxa_map_io();
553 iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc));
555 PCFR |= PCFR_OPDE;
558 MACHINE_START(LUBBOCK, "Intel DBPXA250 Development Platform (aka Lubbock)")
559 /* Maintainer: MontaVista Software Inc. */
560 .phys_io = 0x40000000,
561 .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
562 .map_io = lubbock_map_io,
563 .init_irq = lubbock_init_irq,
564 .timer = &pxa_timer,
565 .init_machine = lubbock_init,
566 MACHINE_END