release/src-rt-6.x.4708/linux/linux-2.6.36/arch/arm/mach-clps711x/include/mach/hardware.h

   1 /*
   2  *  arch/arm/mach-clps711x/include/mach/hardware.h
   3  *
   4  *  This file contains the hardware definitions of the Prospector P720T.
   5  *
   6  *  Copyright (C) 2000 Deep Blue Solutions Ltd.
   7  *
   8  * This program is free software; you can redistribute it and/or modify
   9  * it under the terms of the GNU General Public License as published by
  10  * the Free Software Foundation; either version 2 of the License, or
  11  * (at your option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software
  20  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  21  */
  22 #ifndef __ASM_ARCH_HARDWARE_H
  23 #define __ASM_ARCH_HARDWARE_H
  24
  25
  26 #define CLPS7111_VIRT_BASE      0xff000000
  27 #define CLPS7111_BASE           CLPS7111_VIRT_BASE
  28
  29 /*
  30  * The physical addresses that the external chip select signals map to is
  31  * dependent on the setting of the nMEDCHG signal on EP7211 and EP7212
  32  * processors.  CONFIG_EP72XX_BOOT_ROM is only available if these
  33  * processors are in use.
  34  */
  35 #ifndef CONFIG_EP72XX_ROM_BOOT
  36 #define CS0_PHYS_BASE           (0x00000000)
  37 #define CS1_PHYS_BASE           (0x10000000)
  38 #define CS2_PHYS_BASE           (0x20000000)
  39 #define CS3_PHYS_BASE           (0x30000000)
  40 #define CS4_PHYS_BASE           (0x40000000)
  41 #define CS5_PHYS_BASE           (0x50000000)
  42 #define CS6_PHYS_BASE           (0x60000000)
  43 #define CS7_PHYS_BASE           (0x70000000)
  44 #else
  45 #define CS0_PHYS_BASE           (0x70000000)
  46 #define CS1_PHYS_BASE           (0x60000000)
  47 #define CS2_PHYS_BASE           (0x50000000)
  48 #define CS3_PHYS_BASE           (0x40000000)
  49 #define CS4_PHYS_BASE           (0x30000000)
  50 #define CS5_PHYS_BASE           (0x20000000)
  51 #define CS6_PHYS_BASE           (0x10000000)
  52 #define CS7_PHYS_BASE           (0x00000000)
  53 #endif
  54
  55 #if defined(CONFIG_ARCH_EP7211)
  56
  57 #define EP7211_VIRT_BASE        CLPS7111_VIRT_BASE
  58 #define EP7211_BASE             CLPS7111_VIRT_BASE
  59 #include <asm/hardware/ep7211.h>
  60
  61 #elif defined(CONFIG_ARCH_EP7212)
  62
  63 #define EP7212_VIRT_BASE        CLPS7111_VIRT_BASE
  64 #define EP7212_BASE             CLPS7111_VIRT_BASE
  65 #include <asm/hardware/ep7212.h>
  66
  67 #endif
  68
  69 #define SYSPLD_VIRT_BASE        0xfe000000
  70 #define SYSPLD_BASE             SYSPLD_VIRT_BASE
  71
  72 #if  defined(CONFIG_ARCH_AUTCPU12)
  73
  74 #define  CS89712_VIRT_BASE      CLPS7111_VIRT_BASE
  75 #define  CS89712_BASE           CLPS7111_VIRT_BASE
  76
  77 #include <asm/hardware/clps7111.h>
  78 #include <asm/hardware/ep7212.h>
  79 #include <asm/hardware/cs89712.h>
  80
  81 #endif
  82
  83
  84 #if defined(CONFIG_ARCH_CDB89712)
  85
  86 #include <asm/hardware/clps7111.h>
  87 #include <asm/hardware/ep7212.h>
  88 #include <asm/hardware/cs89712.h>
  89
  90 /* static cdb89712_map_io() areas */
  91 #define REGISTER_START   0x80000000
  92 #define REGISTER_SIZE    0x4000
  93 #define REGISTER_BASE    0xff000000
  94
  95 #define ETHER_START      0x20000000
  96 #define ETHER_SIZE       0x1000
  97 #define ETHER_BASE       0xfe000000
  98
  99 #endif
 100
 101
 102 #if defined(CONFIG_ARCH_EDB7211)
 103
 104 /*
 105  * The extra 8 lines of the keyboard matrix are wired to chip select 3 (nCS3)
 106  * and repeat across it. This is the mapping for it.
 107  *
 108  * In jumpered boot mode, nCS3 is mapped to 0x4000000, not 0x3000000. This
 109  * was cause for much consternation and headscratching. This should probably
 110  * be made a compile/run time kernel option.
 111  */
 112 #define EP7211_PHYS_EXTKBD              CS3_PHYS_BASE   /* physical */
 113
 114 #define EP7211_VIRT_EXTKBD              (0xfd000000)    /* virtual */
 115
 116
 117 /*
 118  * The CS8900A ethernet chip has its I/O registers wired to chip select 2
 119  * (nCS2). This is the mapping for it.
 120  *
 121  * In jumpered boot mode, nCS2 is mapped to 0x5000000, not 0x2000000. This
 122  * was cause for much consternation and headscratching. This should probably
 123  * be made a compile/run time kernel option.
 124  */
 125 #define EP7211_PHYS_CS8900A             CS2_PHYS_BASE   /* physical */
 126
 127 #define EP7211_VIRT_CS8900A             (0xfc000000)    /* virtual */
 128
 129
 130 /*
 131  * The two flash banks are wired to chip selects 0 and 1. This is the mapping
 132  * for them.
 133  *
 134  * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
 135  * in jumpered boot mode.
 136  */
 137 #define EP7211_PHYS_FLASH1              CS0_PHYS_BASE   /* physical */
 138 #define EP7211_PHYS_FLASH2              CS1_PHYS_BASE   /* physical */
 139
 140 #define EP7211_VIRT_FLASH1              (0xfa000000)    /* virtual */
 141 #define EP7211_VIRT_FLASH2              (0xfb000000)    /* virtual */
 142
 143 #endif /* CONFIG_ARCH_EDB7211 */
 144
 145
 146 /*
 147  * Relevant bits in port D, which controls power to the various parts of
 148  * the LCD on the EDB7211.
 149  */
 150 #define EDB_PD1_LCD_DC_DC_EN    (1<<1)
 151 #define EDB_PD2_LCDEN           (1<<2)
 152 #define EDB_PD3_LCDBL           (1<<3)
 153
 154
 155 #if defined(CONFIG_ARCH_CEIVA)
 156
 157 #define  CEIVA_VIRT_BASE        CLPS7111_VIRT_BASE
 158 #define  CEIVA_BASE             CLPS7111_VIRT_BASE
 159
 160 #include <asm/hardware/clps7111.h>
 161 #include <asm/hardware/ep7212.h>
 162
 163
 164 /*
 165  * The two flash banks are wired to chip selects 0 and 1. This is the mapping
 166  * for them.
 167  *
 168  * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
 169  * in jumpered boot mode.
 170  */
 171 #define CEIVA_PHYS_FLASH1       CS0_PHYS_BASE   /* physical */
 172 #define CEIVA_PHYS_FLASH2       CS1_PHYS_BASE   /* physical */
 173
 174 #define CEIVA_VIRT_FLASH1       (0xfa000000)    /* virtual */
 175 #define CEIVA_VIRT_FLASH2       (0xfb000000)    /* virtual */
 176
 177 #define CEIVA_FLASH_SIZE        0x100000
 178 #define CEIVA_FLASH_WIDTH       2
 179
 180 /*
 181  * SED1355 LCD controller
 182  */
 183 #define CEIVA_PHYS_SED1355      CS2_PHYS_BASE
 184 #define CEIVA_VIRT_SED1355      (0xfc000000)
 185
 186 /*
 187  * Relevant bits in port D, which controls power to the various parts of
 188  * the LCD on the Ceiva Photo Max, and reset to the LCD controller.
 189  */
 190
 191 // Reset line to SED1355 (must be high to operate)
 192 #define CEIVA_PD1_LCDRST        (1<<1)
 193 // LCD panel enable (set to one, to enable LCD)
 194 #define CEIVA_PD4_LCDEN         (1<<4)
 195 // Backlight (set to one, to turn on backlight
 196 #define CEIVA_PD5_LCDBL         (1<<5)
 197
 198 /*
 199  * Relevant bits in port B, which report the status of the buttons.
 200  */
 201
 202 // White button
 203 #define CEIVA_PB4_WHT_BTN       (1<<4)
 204 // Black button
 205 #define CEIVA_PB0_BLK_BTN       (1<<0)
 206 #endif // #if defined (CONFIG_ARCH_CEIVA)
 207
 208 #endif