hw/i2c/omap_i2c.c

   1 /*
   2  * TI OMAP on-chip I2C controller.  Only "new I2C" mode supported.
   3  *
   4  * Copyright (C) 2007 Andrzej Zaborowski  <balrog@zabor.org>
   5  *
   6  * This program is free software; you can redistribute it and/or
   7  * modify it under the terms of the GNU General Public License as
   8  * published by the Free Software Foundation; either version 2 of
   9  * the License, or (at your option) any later version.
  10  *
  11  * This program is distributed in the hope that it will be useful,
  12  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  13  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  14  * GNU General Public License for more details.
  15  *
  16  * You should have received a copy of the GNU General Public License along
  17  * with this program; if not, see <http://www.gnu.org/licenses/>.
  18  */
  19 #include "hw/hw.h"
  20 #include "hw/i2c/i2c.h"
  21 #include "hw/arm/omap.h"
  22 #include "hw/sysbus.h"
  23
  24 #define TYPE_OMAP_I2C "omap_i2c"
  25 #define OMAP_I2C(obj) OBJECT_CHECK(OMAPI2CState, (obj), TYPE_OMAP_I2C)
  26
  27 typedef struct OMAPI2CState {
  28     SysBusDevice parent_obj;
  29
  30     MemoryRegion iomem;
  31     qemu_irq irq;
  32     qemu_irq drq[2];
  33     i2c_bus *bus;
  34
  35     uint8_t revision;
  36     void *iclk;
  37     void *fclk;
  38
  39     uint8_t mask;
  40     uint16_t stat;
  41     uint16_t dma;
  42     uint16_t count;
  43     int count_cur;
  44     uint32_t fifo;
  45     int rxlen;
  46     int txlen;
  47     uint16_t control;
  48     uint16_t addr[2];
  49     uint8_t divider;
  50     uint8_t times[2];
  51     uint16_t test;
  52 } OMAPI2CState;
  53
  54 #define OMAP2_INTR_REV  0x34
  55 #define OMAP2_GC_REV    0x34
  56
  57 static void omap_i2c_interrupts_update(OMAPI2CState *s)
  58 {
  59     qemu_set_irq(s->irq, s->stat & s->mask);
  60     if ((s->dma >> 15) & 1)                                     /* RDMA_EN */
  61         qemu_set_irq(s->drq[0], (s->stat >> 3) & 1);            /* RRDY */
  62     if ((s->dma >> 7) & 1)                                      /* XDMA_EN */
  63         qemu_set_irq(s->drq[1], (s->stat >> 4) & 1);            /* XRDY */
  64 }
  65
  66 static void omap_i2c_fifo_run(OMAPI2CState *s)
  67 {
  68     int ack = 1;
  69
  70     if (!i2c_bus_busy(s->bus))
  71         return;
  72
  73     if ((s->control >> 2) & 1) {                                /* RM */
  74         if ((s->control >> 1) & 1) {                            /* STP */
  75             i2c_end_transfer(s->bus);
  76             s->control &= ~(1 << 1);                            /* STP */
  77             s->count_cur = s->count;
  78             s->txlen = 0;
  79         } else if ((s->control >> 9) & 1) {                     /* TRX */
  80             while (ack && s->txlen)
  81                 ack = (i2c_send(s->bus,
  82                                         (s->fifo >> ((-- s->txlen) << 3)) &
  83                                         0xff) >= 0);
  84             s->stat |= 1 << 4;                                  /* XRDY */
  85         } else {
  86             while (s->rxlen < 4)
  87                 s->fifo |= i2c_recv(s->bus) << ((s->rxlen ++) << 3);
  88             s->stat |= 1 << 3;                                  /* RRDY */
  89         }
  90     } else {
  91         if ((s->control >> 9) & 1) {                            /* TRX */
  92             while (ack && s->count_cur && s->txlen) {
  93                 ack = (i2c_send(s->bus,
  94                                         (s->fifo >> ((-- s->txlen) << 3)) &
  95                                         0xff) >= 0);
  96                 s->count_cur --;
  97             }
  98             if (ack && s->count_cur)
  99                 s->stat |= 1 << 4;                              /* XRDY */
 100             else
 101                 s->stat &= ~(1 << 4);                           /* XRDY */
 102             if (!s->count_cur) {
 103                 s->stat |= 1 << 2;                              /* ARDY */
 104                 s->control &= ~(1 << 10);                       /* MST */
 105             }
 106         } else {
 107             while (s->count_cur && s->rxlen < 4) {
 108                 s->fifo |= i2c_recv(s->bus) << ((s->rxlen ++) << 3);
 109                 s->count_cur --;
 110             }
 111             if (s->rxlen)
 112                 s->stat |= 1 << 3;                              /* RRDY */
 113             else
 114                 s->stat &= ~(1 << 3);                           /* RRDY */
 115         }
 116         if (!s->count_cur) {
 117             if ((s->control >> 1) & 1) {                        /* STP */
 118                 i2c_end_transfer(s->bus);
 119                 s->control &= ~(1 << 1);                        /* STP */
 120                 s->count_cur = s->count;
 121                 s->txlen = 0;
 122             } else {
 123                 s->stat |= 1 << 2;                              /* ARDY */
 124                 s->control &= ~(1 << 10);                       /* MST */
 125             }
 126         }
 127     }
 128
 129     s->stat |= (!ack) << 1;                                     /* NACK */
 130     if (!ack)
 131         s->control &= ~(1 << 1);                                /* STP */
 132 }
 133
 134 static void omap_i2c_reset(DeviceState *dev)
 135 {
 136     OMAPI2CState *s = OMAP_I2C(dev);
 137
 138     s->mask = 0;
 139     s->stat = 0;
 140     s->dma = 0;
 141     s->count = 0;
 142     s->count_cur = 0;
 143     s->fifo = 0;
 144     s->rxlen = 0;
 145     s->txlen = 0;
 146     s->control = 0;
 147     s->addr[0] = 0;
 148     s->addr[1] = 0;
 149     s->divider = 0;
 150     s->times[0] = 0;
 151     s->times[1] = 0;
 152     s->test = 0;
 153 }
 154
 155 static uint32_t omap_i2c_read(void *opaque, hwaddr addr)
 156 {
 157     OMAPI2CState *s = opaque;
 158     int offset = addr & OMAP_MPUI_REG_MASK;
 159     uint16_t ret;
 160
 161     switch (offset) {
 162     case 0x00:  /* I2C_REV */
 163         return s->revision;                                     /* REV */
 164
 165     case 0x04:  /* I2C_IE */
 166         return s->mask;
 167
 168     case 0x08:  /* I2C_STAT */
 169         return s->stat | (i2c_bus_busy(s->bus) << 12);
 170
 171     case 0x0c:  /* I2C_IV */
 172         if (s->revision >= OMAP2_INTR_REV)
 173             break;
 174         ret = ffs(s->stat & s->mask);
 175         if (ret)
 176             s->stat ^= 1 << (ret - 1);
 177         omap_i2c_interrupts_update(s);
 178         return ret;
 179
 180     case 0x10:  /* I2C_SYSS */
 181         return (s->control >> 15) & 1;                          /* I2C_EN */
 182
 183     case 0x14:  /* I2C_BUF */
 184         return s->dma;
 185
 186     case 0x18:  /* I2C_CNT */
 187         return s->count_cur;                                    /* DCOUNT */
 188
 189     case 0x1c:  /* I2C_DATA */
 190         ret = 0;
 191         if (s->control & (1 << 14)) {                           /* BE */
 192             ret |= ((s->fifo >> 0) & 0xff) << 8;
 193             ret |= ((s->fifo >> 8) & 0xff) << 0;
 194         } else {
 195             ret |= ((s->fifo >> 8) & 0xff) << 8;
 196             ret |= ((s->fifo >> 0) & 0xff) << 0;
 197         }
 198         if (s->rxlen == 1) {
 199             s->stat |= 1 << 15;                                 /* SBD */
 200             s->rxlen = 0;
 201         } else if (s->rxlen > 1) {
 202             if (s->rxlen > 2)
 203                 s->fifo >>= 16;
 204             s->rxlen -= 2;
 205         } else {
 206             /* XXX: remote access (qualifier) error - what's that?  */
 207         }
 208         if (!s->rxlen) {
 209             s->stat &= ~(1 << 3);                               /* RRDY */
 210             if (((s->control >> 10) & 1) &&                     /* MST */
 211                             ((~s->control >> 9) & 1)) {         /* TRX */
 212                 s->stat |= 1 << 2;                              /* ARDY */
 213                 s->control &= ~(1 << 10);                       /* MST */
 214             }
 215         }
 216         s->stat &= ~(1 << 11);                                  /* ROVR */
 217         omap_i2c_fifo_run(s);
 218         omap_i2c_interrupts_update(s);
 219         return ret;
 220
 221     case 0x20:  /* I2C_SYSC */
 222         return 0;
 223
 224     case 0x24:  /* I2C_CON */
 225         return s->control;
 226
 227     case 0x28:  /* I2C_OA */
 228         return s->addr[0];
 229
 230     case 0x2c:  /* I2C_SA */
 231         return s->addr[1];
 232
 233     case 0x30:  /* I2C_PSC */
 234         return s->divider;
 235
 236     case 0x34:  /* I2C_SCLL */
 237         return s->times[0];
 238
 239     case 0x38:  /* I2C_SCLH */
 240         return s->times[1];
 241
 242     case 0x3c:  /* I2C_SYSTEST */
 243         if (s->test & (1 << 15)) {                              /* ST_EN */
 244             s->test ^= 0xa;
 245             return s->test;
 246         } else
 247             return s->test & ~0x300f;
 248     }
 249
 250     OMAP_BAD_REG(addr);
 251     return 0;
 252 }
 253
 254 static void omap_i2c_write(void *opaque, hwaddr addr,
 255                 uint32_t value)
 256 {
 257     OMAPI2CState *s = opaque;
 258     int offset = addr & OMAP_MPUI_REG_MASK;
 259     int nack;
 260
 261     switch (offset) {
 262     case 0x00:  /* I2C_REV */
 263     case 0x0c:  /* I2C_IV */
 264     case 0x10:  /* I2C_SYSS */
 265         OMAP_RO_REG(addr);
 266         return;
 267
 268     case 0x04:  /* I2C_IE */
 269         s->mask = value & (s->revision < OMAP2_GC_REV ? 0x1f : 0x3f);
 270         break;
 271
 272     case 0x08:  /* I2C_STAT */
 273         if (s->revision < OMAP2_INTR_REV) {
 274             OMAP_RO_REG(addr);
 275             return;
 276         }
 277
 278         /* RRDY and XRDY are reset by hardware. (in all versions???) */
 279         s->stat &= ~(value & 0x27);
 280         omap_i2c_interrupts_update(s);
 281         break;
 282
 283     case 0x14:  /* I2C_BUF */
 284         s->dma = value & 0x8080;
 285         if (value & (1 << 15))                                  /* RDMA_EN */
 286             s->mask &= ~(1 << 3);                               /* RRDY_IE */
 287         if (value & (1 << 7))                                   /* XDMA_EN */
 288             s->mask &= ~(1 << 4);                               /* XRDY_IE */
 289         break;
 290
 291     case 0x18:  /* I2C_CNT */
 292         s->count = value;                                       /* DCOUNT */
 293         break;
 294
 295     case 0x1c:  /* I2C_DATA */
 296         if (s->txlen > 2) {
 297             /* XXX: remote access (qualifier) error - what's that?  */
 298             break;
 299         }
 300         s->fifo <<= 16;
 301         s->txlen += 2;
 302         if (s->control & (1 << 14)) {                           /* BE */
 303             s->fifo |= ((value >> 8) & 0xff) << 8;
 304             s->fifo |= ((value >> 0) & 0xff) << 0;
 305         } else {
 306             s->fifo |= ((value >> 0) & 0xff) << 8;
 307             s->fifo |= ((value >> 8) & 0xff) << 0;
 308         }
 309         s->stat &= ~(1 << 10);                                  /* XUDF */
 310         if (s->txlen > 2)
 311             s->stat &= ~(1 << 4);                               /* XRDY */
 312         omap_i2c_fifo_run(s);
 313         omap_i2c_interrupts_update(s);
 314         break;
 315
 316     case 0x20:  /* I2C_SYSC */
 317         if (s->revision < OMAP2_INTR_REV) {
 318             OMAP_BAD_REG(addr);
 319             return;
 320         }
 321
 322         if (value & 2) {
 323             omap_i2c_reset(DEVICE(s));
 324         }
 325         break;
 326
 327     case 0x24:  /* I2C_CON */
 328         s->control = value & 0xcf87;
 329         if (~value & (1 << 15)) {                               /* I2C_EN */
 330             if (s->revision < OMAP2_INTR_REV) {
 331                 omap_i2c_reset(DEVICE(s));
 332             }
 333             break;
 334         }
 335         if ((value & (1 << 15)) && !(value & (1 << 10))) {      /* MST */
 336             fprintf(stderr, "%s: I^2C slave mode not supported\n",
 337                             __FUNCTION__);
 338             break;
 339         }
 340         if ((value & (1 << 15)) && value & (1 << 8)) {          /* XA */
 341             fprintf(stderr, "%s: 10-bit addressing mode not supported\n",
 342                             __FUNCTION__);
 343             break;
 344         }
 345         if ((value & (1 << 15)) && value & (1 << 0)) {          /* STT */
 346             nack = !!i2c_start_transfer(s->bus, s->addr[1],     /* SA */
 347                             (~value >> 9) & 1);                 /* TRX */
 348             s->stat |= nack << 1;                               /* NACK */
 349             s->control &= ~(1 << 0);                            /* STT */
 350             s->fifo = 0;
 351             if (nack)
 352                 s->control &= ~(1 << 1);                        /* STP */
 353             else {
 354                 s->count_cur = s->count;
 355                 omap_i2c_fifo_run(s);
 356             }
 357             omap_i2c_interrupts_update(s);
 358         }
 359         break;
 360
 361     case 0x28:  /* I2C_OA */
 362         s->addr[0] = value & 0x3ff;
 363         break;
 364
 365     case 0x2c:  /* I2C_SA */
 366         s->addr[1] = value & 0x3ff;
 367         break;
 368
 369     case 0x30:  /* I2C_PSC */
 370         s->divider = value;
 371         break;
 372
 373     case 0x34:  /* I2C_SCLL */
 374         s->times[0] = value;
 375         break;
 376
 377     case 0x38:  /* I2C_SCLH */
 378         s->times[1] = value;
 379         break;
 380
 381     case 0x3c:  /* I2C_SYSTEST */
 382         s->test = value & 0xf80f;
 383         if (value & (1 << 11))                                  /* SBB */
 384             if (s->revision >= OMAP2_INTR_REV) {
 385                 s->stat |= 0x3f;
 386                 omap_i2c_interrupts_update(s);
 387             }
 388         if (value & (1 << 15))                                  /* ST_EN */
 389             fprintf(stderr, "%s: System Test not supported\n", __FUNCTION__);
 390         break;
 391
 392     default:
 393         OMAP_BAD_REG(addr);
 394         return;
 395     }
 396 }
 397
 398 static void omap_i2c_writeb(void *opaque, hwaddr addr,
 399                 uint32_t value)
 400 {
 401     OMAPI2CState *s = opaque;
 402     int offset = addr & OMAP_MPUI_REG_MASK;
 403
 404     switch (offset) {
 405     case 0x1c:  /* I2C_DATA */
 406         if (s->txlen > 2) {
 407             /* XXX: remote access (qualifier) error - what's that?  */
 408             break;
 409         }
 410         s->fifo <<= 8;
 411         s->txlen += 1;
 412         s->fifo |= value & 0xff;
 413         s->stat &= ~(1 << 10);                                  /* XUDF */
 414         if (s->txlen > 2)
 415             s->stat &= ~(1 << 4);                               /* XRDY */
 416         omap_i2c_fifo_run(s);
 417         omap_i2c_interrupts_update(s);
 418         break;
 419
 420     default:
 421         OMAP_BAD_REG(addr);
 422         return;
 423     }
 424 }
 425
 426 static const MemoryRegionOps omap_i2c_ops = {
 427     .old_mmio = {
 428         .read = {
 429             omap_badwidth_read16,
 430             omap_i2c_read,
 431             omap_badwidth_read16,
 432         },
 433         .write = {
 434             omap_i2c_writeb, /* Only the last fifo write can be 8 bit.  */
 435             omap_i2c_write,
 436             omap_badwidth_write16,
 437         },
 438     },
 439     .endianness = DEVICE_NATIVE_ENDIAN,
 440 };
 441
 442 static int omap_i2c_init(SysBusDevice *sbd)
 443 {
 444     DeviceState *dev = DEVICE(sbd);
 445     OMAPI2CState *s = OMAP_I2C(dev);
 446
 447     if (!s->fclk) {
 448         hw_error("omap_i2c: fclk not connected\n");
 449     }
 450     if (s->revision >= OMAP2_INTR_REV && !s->iclk) {
 451         /* Note that OMAP1 doesn't have a separate interface clock */
 452         hw_error("omap_i2c: iclk not connected\n");
 453     }
 454     sysbus_init_irq(sbd, &s->irq);
 455     sysbus_init_irq(sbd, &s->drq[0]);
 456     sysbus_init_irq(sbd, &s->drq[1]);
 457     memory_region_init_io(&s->iomem, OBJECT(s), &omap_i2c_ops, s, "omap.i2c",
 458                           (s->revision < OMAP2_INTR_REV) ? 0x800 : 0x1000);
 459     sysbus_init_mmio(sbd, &s->iomem);
 460     s->bus = i2c_init_bus(dev, NULL);
 461     return 0;
 462 }
 463
 464 static Property omap_i2c_properties[] = {
 465     DEFINE_PROP_UINT8("revision", OMAPI2CState, revision, 0),
 466     DEFINE_PROP_PTR("iclk", OMAPI2CState, iclk),
 467     DEFINE_PROP_PTR("fclk", OMAPI2CState, fclk),
 468     DEFINE_PROP_END_OF_LIST(),
 469 };
 470
 471 static void omap_i2c_class_init(ObjectClass *klass, void *data)
 472 {
 473     DeviceClass *dc = DEVICE_CLASS(klass);
 474     SysBusDeviceClass *k = SYS_BUS_DEVICE_CLASS(klass);
 475     k->init = omap_i2c_init;
 476     dc->props = omap_i2c_properties;
 477     dc->reset = omap_i2c_reset;
 478 }
 479
 480 static const TypeInfo omap_i2c_info = {
 481     .name = TYPE_OMAP_I2C,
 482     .parent = TYPE_SYS_BUS_DEVICE,
 483     .instance_size = sizeof(OMAPI2CState),
 484     .class_init = omap_i2c_class_init,
 485 };
 486
 487 static void omap_i2c_register_types(void)
 488 {
 489     type_register_static(&omap_i2c_info);
 490 }
 491
 492 i2c_bus *omap_i2c_bus(DeviceState *omap_i2c)
 493 {
 494     OMAPI2CState *s = OMAP_I2C(omap_i2c);
 495     return s->bus;
 496 }
 497
 498 type_init(omap_i2c_register_types)