hw/input/lm832x.c

   1 /*
   2  * National Semiconductor LM8322/8323 GPIO keyboard & PWM chips.
   3  *
   4  * Copyright (C) 2008 Nokia Corporation
   5  * Written by Andrzej Zaborowski <andrew@openedhand.com>
   6  *
   7  * This program is free software; you can redistribute it and/or
   8  * modify it under the terms of the GNU General Public License as
   9  * published by the Free Software Foundation; either version 2 or
  10  * (at your option) version 3 of the License.
  11  *
  12  * This program is distributed in the hope that it will be useful,
  13  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  14  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  15  * GNU General Public License for more details.
  16  *
  17  * You should have received a copy of the GNU General Public License along
  18  * with this program; if not, see <http://www.gnu.org/licenses/>.
  19  */
  20
  21 #include "qemu/osdep.h"
  22 #include "hw/hw.h"
  23 #include "hw/i2c/i2c.h"
  24 #include "qemu/timer.h"
  25 #include "ui/console.h"
  26
  27 #define TYPE_LM8323 "lm8323"
  28 #define LM8323(obj) OBJECT_CHECK(LM823KbdState, (obj), TYPE_LM8323)
  29
  30 typedef struct {
  31     I2CSlave parent_obj;
  32
  33     uint8_t i2c_dir;
  34     uint8_t i2c_cycle;
  35     uint8_t reg;
  36
  37     qemu_irq nirq;
  38     uint16_t model;
  39
  40     struct {
  41         qemu_irq out[2];
  42         int in[2][2];
  43     } mux;
  44
  45     uint8_t config;
  46     uint8_t status;
  47     uint8_t acttime;
  48     uint8_t error;
  49     uint8_t clock;
  50
  51     struct {
  52         uint16_t pull;
  53         uint16_t mask;
  54         uint16_t dir;
  55         uint16_t level;
  56         qemu_irq out[16];
  57     } gpio;
  58
  59     struct {
  60         uint8_t dbnctime;
  61         uint8_t size;
  62         uint8_t start;
  63         uint8_t len;
  64         uint8_t fifo[16];
  65     } kbd;
  66
  67     struct {
  68         uint16_t file[256];
  69         uint8_t faddr;
  70         uint8_t addr[3];
  71         QEMUTimer *tm[3];
  72     } pwm;
  73 } LM823KbdState;
  74
  75 #define INT_KEYPAD              (1 << 0)
  76 #define INT_ERROR               (1 << 3)
  77 #define INT_NOINIT              (1 << 4)
  78 #define INT_PWMEND(n)           (1 << (5 + n))
  79
  80 #define ERR_BADPAR              (1 << 0)
  81 #define ERR_CMDUNK              (1 << 1)
  82 #define ERR_KEYOVR              (1 << 2)
  83 #define ERR_FIFOOVR             (1 << 6)
  84
  85 static void lm_kbd_irq_update(LM823KbdState *s)
  86 {
  87     qemu_set_irq(s->nirq, !s->status);
  88 }
  89
  90 static void lm_kbd_gpio_update(LM823KbdState *s)
  91 {
  92 }
  93
  94 static void lm_kbd_reset(LM823KbdState *s)
  95 {
  96     s->config = 0x80;
  97     s->status = INT_NOINIT;
  98     s->acttime = 125;
  99     s->kbd.dbnctime = 3;
 100     s->kbd.size = 0x33;
 101     s->clock = 0x08;
 102
 103     lm_kbd_irq_update(s);
 104     lm_kbd_gpio_update(s);
 105 }
 106
 107 static void lm_kbd_error(LM823KbdState *s, int err)
 108 {
 109     s->error |= err;
 110     s->status |= INT_ERROR;
 111     lm_kbd_irq_update(s);
 112 }
 113
 114 static void lm_kbd_pwm_tick(LM823KbdState *s, int line)
 115 {
 116 }
 117
 118 static void lm_kbd_pwm_start(LM823KbdState *s, int line)
 119 {
 120     lm_kbd_pwm_tick(s, line);
 121 }
 122
 123 static void lm_kbd_pwm0_tick(void *opaque)
 124 {
 125     lm_kbd_pwm_tick(opaque, 0);
 126 }
 127 static void lm_kbd_pwm1_tick(void *opaque)
 128 {
 129     lm_kbd_pwm_tick(opaque, 1);
 130 }
 131 static void lm_kbd_pwm2_tick(void *opaque)
 132 {
 133     lm_kbd_pwm_tick(opaque, 2);
 134 }
 135
 136 enum {
 137     LM832x_CMD_READ_ID          = 0x80, /* Read chip ID. */
 138     LM832x_CMD_WRITE_CFG        = 0x81, /* Set configuration item. */
 139     LM832x_CMD_READ_INT         = 0x82, /* Get interrupt status. */
 140     LM832x_CMD_RESET            = 0x83, /* Reset, same as external one */
 141     LM823x_CMD_WRITE_PULL_DOWN  = 0x84, /* Select GPIO pull-up/down. */
 142     LM832x_CMD_WRITE_PORT_SEL   = 0x85, /* Select GPIO in/out. */
 143     LM832x_CMD_WRITE_PORT_STATE = 0x86, /* Set GPIO pull-up/down. */
 144     LM832x_CMD_READ_PORT_SEL    = 0x87, /* Get GPIO in/out. */
 145     LM832x_CMD_READ_PORT_STATE  = 0x88, /* Get GPIO pull-up/down. */
 146     LM832x_CMD_READ_FIFO        = 0x89, /* Read byte from FIFO. */
 147     LM832x_CMD_RPT_READ_FIFO    = 0x8a, /* Read FIFO (no increment). */
 148     LM832x_CMD_SET_ACTIVE       = 0x8b, /* Set active time. */
 149     LM832x_CMD_READ_ERROR       = 0x8c, /* Get error status. */
 150     LM832x_CMD_READ_ROTATOR     = 0x8e, /* Read rotator status. */
 151     LM832x_CMD_SET_DEBOUNCE     = 0x8f, /* Set debouncing time. */
 152     LM832x_CMD_SET_KEY_SIZE     = 0x90, /* Set keypad size. */
 153     LM832x_CMD_READ_KEY_SIZE    = 0x91, /* Get keypad size. */
 154     LM832x_CMD_READ_CFG         = 0x92, /* Get configuration item. */
 155     LM832x_CMD_WRITE_CLOCK      = 0x93, /* Set clock config. */
 156     LM832x_CMD_READ_CLOCK       = 0x94, /* Get clock config. */
 157     LM832x_CMD_PWM_WRITE        = 0x95, /* Write PWM script. */
 158     LM832x_CMD_PWM_START        = 0x96, /* Start PWM engine. */
 159     LM832x_CMD_PWM_STOP         = 0x97, /* Stop PWM engine. */
 160     LM832x_GENERAL_ERROR        = 0xff, /* There was one error.
 161                                            Previously was represented by -1
 162                                            This is not a command */
 163 };
 164
 165 #define LM832x_MAX_KPX          8
 166 #define LM832x_MAX_KPY          12
 167
 168 static uint8_t lm_kbd_read(LM823KbdState *s, int reg, int byte)
 169 {
 170     int ret;
 171
 172     switch (reg) {
 173     case LM832x_CMD_READ_ID:
 174         ret = 0x0400;
 175         break;
 176
 177     case LM832x_CMD_READ_INT:
 178         ret = s->status;
 179         if (!(s->status & INT_NOINIT)) {
 180             s->status = 0;
 181             lm_kbd_irq_update(s);
 182         }
 183         break;
 184
 185     case LM832x_CMD_READ_PORT_SEL:
 186         ret = s->gpio.dir;
 187         break;
 188     case LM832x_CMD_READ_PORT_STATE:
 189         ret = s->gpio.mask;
 190         break;
 191
 192     case LM832x_CMD_READ_FIFO:
 193         if (s->kbd.len <= 1)
 194             return 0x00;
 195
 196         /* Example response from the two commands after a INT_KEYPAD
 197          * interrupt caused by the key 0x3c being pressed:
 198          * RPT_READ_FIFO: 55 bc 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01
 199          *     READ_FIFO: bc 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01
 200          * RPT_READ_FIFO: bc 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01
 201          *
 202          * 55 is the code of the key release event serviced in the previous
 203          * interrupt handling.
 204          *
 205          * TODO: find out whether the FIFO is advanced a single character
 206          * before reading every byte or the whole size of the FIFO at the
 207          * last LM832x_CMD_READ_FIFO.  This affects LM832x_CMD_RPT_READ_FIFO
 208          * output in cases where there are more than one event in the FIFO.
 209          * Assume 0xbc and 0x3c events are in the FIFO:
 210          * RPT_READ_FIFO: 55 bc 3c 00 4e ff 0a 50 08 00 29 d9 08 01 c9
 211          *     READ_FIFO: bc 3c 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9
 212          * Does RPT_READ_FIFO now return 0xbc and 0x3c or only 0x3c?
 213          */
 214         s->kbd.start ++;
 215         s->kbd.start &= sizeof(s->kbd.fifo) - 1;
 216         s->kbd.len --;
 217
 218         return s->kbd.fifo[s->kbd.start];
 219     case LM832x_CMD_RPT_READ_FIFO:
 220         if (byte >= s->kbd.len)
 221             return 0x00;
 222
 223         return s->kbd.fifo[(s->kbd.start + byte) & (sizeof(s->kbd.fifo) - 1)];
 224
 225     case LM832x_CMD_READ_ERROR:
 226         return s->error;
 227
 228     case LM832x_CMD_READ_ROTATOR:
 229         return 0;
 230
 231     case LM832x_CMD_READ_KEY_SIZE:
 232         return s->kbd.size;
 233
 234     case LM832x_CMD_READ_CFG:
 235         return s->config & 0xf;
 236
 237     case LM832x_CMD_READ_CLOCK:
 238         return (s->clock & 0xfc) | 2;
 239
 240     default:
 241         lm_kbd_error(s, ERR_CMDUNK);
 242         fprintf(stderr, "%s: unknown command %02x\n", __FUNCTION__, reg);
 243         return 0x00;
 244     }
 245
 246     return ret >> (byte << 3);
 247 }
 248
 249 static void lm_kbd_write(LM823KbdState *s, int reg, int byte, uint8_t value)
 250 {
 251     switch (reg) {
 252     case LM832x_CMD_WRITE_CFG:
 253         s->config = value;
 254         /* This must be done whenever s->mux.in is updated (never).  */
 255         if ((s->config >> 1) & 1)                       /* MUX1EN */
 256             qemu_set_irq(s->mux.out[0], s->mux.in[0][(s->config >> 0) & 1]);
 257         if ((s->config >> 3) & 1)                       /* MUX2EN */
 258             qemu_set_irq(s->mux.out[0], s->mux.in[0][(s->config >> 2) & 1]);
 259         /* TODO: check that this is issued only following the chip reset
 260          * and not in the middle of operation and that it is followed by
 261          * the GPIO ports re-resablishing through WRITE_PORT_SEL and
 262          * WRITE_PORT_STATE (using a timer perhaps) and otherwise output
 263          * warnings.  */
 264         s->status = 0;
 265         lm_kbd_irq_update(s);
 266         s->kbd.len = 0;
 267         s->kbd.start = 0;
 268         s->reg = LM832x_GENERAL_ERROR;
 269         break;
 270
 271     case LM832x_CMD_RESET:
 272         if (value == 0xaa)
 273             lm_kbd_reset(s);
 274         else
 275             lm_kbd_error(s, ERR_BADPAR);
 276         s->reg = LM832x_GENERAL_ERROR;
 277         break;
 278
 279     case LM823x_CMD_WRITE_PULL_DOWN:
 280         if (!byte)
 281             s->gpio.pull = value;
 282         else {
 283             s->gpio.pull |= value << 8;
 284             lm_kbd_gpio_update(s);
 285             s->reg = LM832x_GENERAL_ERROR;
 286         }
 287         break;
 288     case LM832x_CMD_WRITE_PORT_SEL:
 289         if (!byte)
 290             s->gpio.dir = value;
 291         else {
 292             s->gpio.dir |= value << 8;
 293             lm_kbd_gpio_update(s);
 294             s->reg = LM832x_GENERAL_ERROR;
 295         }
 296         break;
 297     case LM832x_CMD_WRITE_PORT_STATE:
 298         if (!byte)
 299             s->gpio.mask = value;
 300         else {
 301             s->gpio.mask |= value << 8;
 302             lm_kbd_gpio_update(s);
 303             s->reg = LM832x_GENERAL_ERROR;
 304         }
 305         break;
 306
 307     case LM832x_CMD_SET_ACTIVE:
 308         s->acttime = value;
 309         s->reg = LM832x_GENERAL_ERROR;
 310         break;
 311
 312     case LM832x_CMD_SET_DEBOUNCE:
 313         s->kbd.dbnctime = value;
 314         s->reg = LM832x_GENERAL_ERROR;
 315         if (!value)
 316             lm_kbd_error(s, ERR_BADPAR);
 317         break;
 318
 319     case LM832x_CMD_SET_KEY_SIZE:
 320         s->kbd.size = value;
 321         s->reg = LM832x_GENERAL_ERROR;
 322         if (
 323                         (value & 0xf) < 3 || (value & 0xf) > LM832x_MAX_KPY ||
 324                         (value >> 4) < 3 || (value >> 4) > LM832x_MAX_KPX)
 325             lm_kbd_error(s, ERR_BADPAR);
 326         break;
 327
 328     case LM832x_CMD_WRITE_CLOCK:
 329         s->clock = value;
 330         s->reg = LM832x_GENERAL_ERROR;
 331         if ((value & 3) && (value & 3) != 3) {
 332             lm_kbd_error(s, ERR_BADPAR);
 333             fprintf(stderr, "%s: invalid clock setting in RCPWM\n",
 334                             __FUNCTION__);
 335         }
 336         /* TODO: Validate that the command is only issued once */
 337         break;
 338
 339     case LM832x_CMD_PWM_WRITE:
 340         if (byte == 0) {
 341             if (!(value & 3) || (value >> 2) > 59) {
 342                 lm_kbd_error(s, ERR_BADPAR);
 343                 s->reg = LM832x_GENERAL_ERROR;
 344                 break;
 345             }
 346
 347             s->pwm.faddr = value;
 348             s->pwm.file[s->pwm.faddr] = 0;
 349         } else if (byte == 1) {
 350             s->pwm.file[s->pwm.faddr] |= value << 8;
 351         } else if (byte == 2) {
 352             s->pwm.file[s->pwm.faddr] |= value << 0;
 353             s->reg = LM832x_GENERAL_ERROR;
 354         }
 355         break;
 356     case LM832x_CMD_PWM_START:
 357         s->reg = LM832x_GENERAL_ERROR;
 358         if (!(value & 3) || (value >> 2) > 59) {
 359             lm_kbd_error(s, ERR_BADPAR);
 360             break;
 361         }
 362
 363         s->pwm.addr[(value & 3) - 1] = value >> 2;
 364         lm_kbd_pwm_start(s, (value & 3) - 1);
 365         break;
 366     case LM832x_CMD_PWM_STOP:
 367         s->reg = LM832x_GENERAL_ERROR;
 368         if (!(value & 3)) {
 369             lm_kbd_error(s, ERR_BADPAR);
 370             break;
 371         }
 372
 373         timer_del(s->pwm.tm[(value & 3) - 1]);
 374         break;
 375
 376     case LM832x_GENERAL_ERROR:
 377         lm_kbd_error(s, ERR_BADPAR);
 378         break;
 379     default:
 380         lm_kbd_error(s, ERR_CMDUNK);
 381         fprintf(stderr, "%s: unknown command %02x\n", __FUNCTION__, reg);
 382         break;
 383     }
 384 }
 385
 386 static int lm_i2c_event(I2CSlave *i2c, enum i2c_event event)
 387 {
 388     LM823KbdState *s = LM8323(i2c);
 389
 390     switch (event) {
 391     case I2C_START_RECV:
 392     case I2C_START_SEND:
 393         s->i2c_cycle = 0;
 394         s->i2c_dir = (event == I2C_START_SEND);
 395         break;
 396
 397     default:
 398         break;
 399     }
 400
 401     return 0;
 402 }
 403
 404 static int lm_i2c_rx(I2CSlave *i2c)
 405 {
 406     LM823KbdState *s = LM8323(i2c);
 407
 408     return lm_kbd_read(s, s->reg, s->i2c_cycle ++);
 409 }
 410
 411 static int lm_i2c_tx(I2CSlave *i2c, uint8_t data)
 412 {
 413     LM823KbdState *s = LM8323(i2c);
 414
 415     if (!s->i2c_cycle)
 416         s->reg = data;
 417     else
 418         lm_kbd_write(s, s->reg, s->i2c_cycle - 1, data);
 419     s->i2c_cycle ++;
 420
 421     return 0;
 422 }
 423
 424 static int lm_kbd_post_load(void *opaque, int version_id)
 425 {
 426     LM823KbdState *s = opaque;
 427
 428     lm_kbd_irq_update(s);
 429     lm_kbd_gpio_update(s);
 430
 431     return 0;
 432 }
 433
 434 static const VMStateDescription vmstate_lm_kbd = {
 435     .name = "LM8323",
 436     .version_id = 0,
 437     .minimum_version_id = 0,
 438     .post_load = lm_kbd_post_load,
 439     .fields = (VMStateField[]) {
 440         VMSTATE_I2C_SLAVE(parent_obj, LM823KbdState),
 441         VMSTATE_UINT8(i2c_dir, LM823KbdState),
 442         VMSTATE_UINT8(i2c_cycle, LM823KbdState),
 443         VMSTATE_UINT8(reg, LM823KbdState),
 444         VMSTATE_UINT8(config, LM823KbdState),
 445         VMSTATE_UINT8(status, LM823KbdState),
 446         VMSTATE_UINT8(acttime, LM823KbdState),
 447         VMSTATE_UINT8(error, LM823KbdState),
 448         VMSTATE_UINT8(clock, LM823KbdState),
 449         VMSTATE_UINT16(gpio.pull, LM823KbdState),
 450         VMSTATE_UINT16(gpio.mask, LM823KbdState),
 451         VMSTATE_UINT16(gpio.dir, LM823KbdState),
 452         VMSTATE_UINT16(gpio.level, LM823KbdState),
 453         VMSTATE_UINT8(kbd.dbnctime, LM823KbdState),
 454         VMSTATE_UINT8(kbd.size, LM823KbdState),
 455         VMSTATE_UINT8(kbd.start, LM823KbdState),
 456         VMSTATE_UINT8(kbd.len, LM823KbdState),
 457         VMSTATE_BUFFER(kbd.fifo, LM823KbdState),
 458         VMSTATE_UINT16_ARRAY(pwm.file, LM823KbdState, 256),
 459         VMSTATE_UINT8(pwm.faddr, LM823KbdState),
 460         VMSTATE_BUFFER(pwm.addr, LM823KbdState),
 461         VMSTATE_TIMER_PTR_ARRAY(pwm.tm, LM823KbdState, 3),
 462         VMSTATE_END_OF_LIST()
 463     }
 464 };
 465
 466
 467 static int lm8323_init(I2CSlave *i2c)
 468 {
 469     LM823KbdState *s = LM8323(i2c);
 470
 471     s->model = 0x8323;
 472     s->pwm.tm[0] = timer_new_ns(QEMU_CLOCK_VIRTUAL, lm_kbd_pwm0_tick, s);
 473     s->pwm.tm[1] = timer_new_ns(QEMU_CLOCK_VIRTUAL, lm_kbd_pwm1_tick, s);
 474     s->pwm.tm[2] = timer_new_ns(QEMU_CLOCK_VIRTUAL, lm_kbd_pwm2_tick, s);
 475     qdev_init_gpio_out(DEVICE(i2c), &s->nirq, 1);
 476
 477     lm_kbd_reset(s);
 478
 479     qemu_register_reset((void *) lm_kbd_reset, s);
 480     return 0;
 481 }
 482
 483 void lm832x_key_event(DeviceState *dev, int key, int state)
 484 {
 485     LM823KbdState *s = LM8323(dev);
 486
 487     if ((s->status & INT_ERROR) && (s->error & ERR_FIFOOVR))
 488         return;
 489
 490     if (s->kbd.len >= sizeof(s->kbd.fifo)) {
 491         lm_kbd_error(s, ERR_FIFOOVR);
 492         return;
 493     }
 494
 495     s->kbd.fifo[(s->kbd.start + s->kbd.len ++) & (sizeof(s->kbd.fifo) - 1)] =
 496             key | (state << 7);
 497
 498     /* We never set ERR_KEYOVR because we support multiple keys fine.  */
 499     s->status |= INT_KEYPAD;
 500     lm_kbd_irq_update(s);
 501 }
 502
 503 static void lm8323_class_init(ObjectClass *klass, void *data)
 504 {
 505     DeviceClass *dc = DEVICE_CLASS(klass);
 506     I2CSlaveClass *k = I2C_SLAVE_CLASS(klass);
 507
 508     k->init = lm8323_init;
 509     k->event = lm_i2c_event;
 510     k->recv = lm_i2c_rx;
 511     k->send = lm_i2c_tx;
 512     dc->vmsd = &vmstate_lm_kbd;
 513 }
 514
 515 static const TypeInfo lm8323_info = {
 516     .name          = TYPE_LM8323,
 517     .parent        = TYPE_I2C_SLAVE,
 518     .instance_size = sizeof(LM823KbdState),
 519     .class_init    = lm8323_class_init,
 520 };
 521
 522 static void lm832x_register_types(void)
 523 {
 524     type_register_static(&lm8323_info);
 525 }
 526
 527 type_init(lm832x_register_types)