qemu-iotests: Treat custom TEST_DIR in 051
[qemu/ar7.git] / hw / sd / pl181.c
blob3ad7e925c58b8484fccc741eed537039dab3f8c5
1 /*
2 * Arm PrimeCell PL181 MultiMedia Card Interface
4 * Copyright (c) 2007 CodeSourcery.
5 * Written by Paul Brook
7 * This code is licensed under the GPL.
8 */
10 #include "qemu/osdep.h"
11 #include "sysemu/blockdev.h"
12 #include "hw/sysbus.h"
13 #include "hw/sd/sd.h"
14 #include "qemu/log.h"
15 #include "qapi/error.h"
17 //#define DEBUG_PL181 1
19 #ifdef DEBUG_PL181
20 #define DPRINTF(fmt, ...) \
21 do { printf("pl181: " fmt , ## __VA_ARGS__); } while (0)
22 #else
23 #define DPRINTF(fmt, ...) do {} while(0)
24 #endif
26 #define PL181_FIFO_LEN 16
28 #define TYPE_PL181 "pl181"
29 #define PL181(obj) OBJECT_CHECK(PL181State, (obj), TYPE_PL181)
31 typedef struct PL181State {
32 SysBusDevice parent_obj;
34 MemoryRegion iomem;
35 SDState *card;
36 uint32_t clock;
37 uint32_t power;
38 uint32_t cmdarg;
39 uint32_t cmd;
40 uint32_t datatimer;
41 uint32_t datalength;
42 uint32_t respcmd;
43 uint32_t response[4];
44 uint32_t datactrl;
45 uint32_t datacnt;
46 uint32_t status;
47 uint32_t mask[2];
48 int32_t fifo_pos;
49 int32_t fifo_len;
50 /* The linux 2.6.21 driver is buggy, and misbehaves if new data arrives
51 while it is reading the FIFO. We hack around this by deferring
52 subsequent transfers until after the driver polls the status word.
53 http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=4446/1
55 int32_t linux_hack;
56 uint32_t fifo[PL181_FIFO_LEN];
57 qemu_irq irq[2];
58 /* GPIO outputs for 'card is readonly' and 'card inserted' */
59 qemu_irq cardstatus[2];
60 } PL181State;
62 static const VMStateDescription vmstate_pl181 = {
63 .name = "pl181",
64 .version_id = 1,
65 .minimum_version_id = 1,
66 .fields = (VMStateField[]) {
67 VMSTATE_UINT32(clock, PL181State),
68 VMSTATE_UINT32(power, PL181State),
69 VMSTATE_UINT32(cmdarg, PL181State),
70 VMSTATE_UINT32(cmd, PL181State),
71 VMSTATE_UINT32(datatimer, PL181State),
72 VMSTATE_UINT32(datalength, PL181State),
73 VMSTATE_UINT32(respcmd, PL181State),
74 VMSTATE_UINT32_ARRAY(response, PL181State, 4),
75 VMSTATE_UINT32(datactrl, PL181State),
76 VMSTATE_UINT32(datacnt, PL181State),
77 VMSTATE_UINT32(status, PL181State),
78 VMSTATE_UINT32_ARRAY(mask, PL181State, 2),
79 VMSTATE_INT32(fifo_pos, PL181State),
80 VMSTATE_INT32(fifo_len, PL181State),
81 VMSTATE_INT32(linux_hack, PL181State),
82 VMSTATE_UINT32_ARRAY(fifo, PL181State, PL181_FIFO_LEN),
83 VMSTATE_END_OF_LIST()
87 #define PL181_CMD_INDEX 0x3f
88 #define PL181_CMD_RESPONSE (1 << 6)
89 #define PL181_CMD_LONGRESP (1 << 7)
90 #define PL181_CMD_INTERRUPT (1 << 8)
91 #define PL181_CMD_PENDING (1 << 9)
92 #define PL181_CMD_ENABLE (1 << 10)
94 #define PL181_DATA_ENABLE (1 << 0)
95 #define PL181_DATA_DIRECTION (1 << 1)
96 #define PL181_DATA_MODE (1 << 2)
97 #define PL181_DATA_DMAENABLE (1 << 3)
99 #define PL181_STATUS_CMDCRCFAIL (1 << 0)
100 #define PL181_STATUS_DATACRCFAIL (1 << 1)
101 #define PL181_STATUS_CMDTIMEOUT (1 << 2)
102 #define PL181_STATUS_DATATIMEOUT (1 << 3)
103 #define PL181_STATUS_TXUNDERRUN (1 << 4)
104 #define PL181_STATUS_RXOVERRUN (1 << 5)
105 #define PL181_STATUS_CMDRESPEND (1 << 6)
106 #define PL181_STATUS_CMDSENT (1 << 7)
107 #define PL181_STATUS_DATAEND (1 << 8)
108 #define PL181_STATUS_DATABLOCKEND (1 << 10)
109 #define PL181_STATUS_CMDACTIVE (1 << 11)
110 #define PL181_STATUS_TXACTIVE (1 << 12)
111 #define PL181_STATUS_RXACTIVE (1 << 13)
112 #define PL181_STATUS_TXFIFOHALFEMPTY (1 << 14)
113 #define PL181_STATUS_RXFIFOHALFFULL (1 << 15)
114 #define PL181_STATUS_TXFIFOFULL (1 << 16)
115 #define PL181_STATUS_RXFIFOFULL (1 << 17)
116 #define PL181_STATUS_TXFIFOEMPTY (1 << 18)
117 #define PL181_STATUS_RXFIFOEMPTY (1 << 19)
118 #define PL181_STATUS_TXDATAAVLBL (1 << 20)
119 #define PL181_STATUS_RXDATAAVLBL (1 << 21)
121 #define PL181_STATUS_TX_FIFO (PL181_STATUS_TXACTIVE \
122 |PL181_STATUS_TXFIFOHALFEMPTY \
123 |PL181_STATUS_TXFIFOFULL \
124 |PL181_STATUS_TXFIFOEMPTY \
125 |PL181_STATUS_TXDATAAVLBL)
126 #define PL181_STATUS_RX_FIFO (PL181_STATUS_RXACTIVE \
127 |PL181_STATUS_RXFIFOHALFFULL \
128 |PL181_STATUS_RXFIFOFULL \
129 |PL181_STATUS_RXFIFOEMPTY \
130 |PL181_STATUS_RXDATAAVLBL)
132 static const unsigned char pl181_id[] =
133 { 0x81, 0x11, 0x04, 0x00, 0x0d, 0xf0, 0x05, 0xb1 };
135 static void pl181_update(PL181State *s)
137 int i;
138 for (i = 0; i < 2; i++) {
139 qemu_set_irq(s->irq[i], (s->status & s->mask[i]) != 0);
143 static void pl181_fifo_push(PL181State *s, uint32_t value)
145 int n;
147 if (s->fifo_len == PL181_FIFO_LEN) {
148 fprintf(stderr, "pl181: FIFO overflow\n");
149 return;
151 n = (s->fifo_pos + s->fifo_len) & (PL181_FIFO_LEN - 1);
152 s->fifo_len++;
153 s->fifo[n] = value;
154 DPRINTF("FIFO push %08x\n", (int)value);
157 static uint32_t pl181_fifo_pop(PL181State *s)
159 uint32_t value;
161 if (s->fifo_len == 0) {
162 fprintf(stderr, "pl181: FIFO underflow\n");
163 return 0;
165 value = s->fifo[s->fifo_pos];
166 s->fifo_len--;
167 s->fifo_pos = (s->fifo_pos + 1) & (PL181_FIFO_LEN - 1);
168 DPRINTF("FIFO pop %08x\n", (int)value);
169 return value;
172 static void pl181_send_command(PL181State *s)
174 SDRequest request;
175 uint8_t response[16];
176 int rlen;
178 request.cmd = s->cmd & PL181_CMD_INDEX;
179 request.arg = s->cmdarg;
180 DPRINTF("Command %d %08x\n", request.cmd, request.arg);
181 rlen = sd_do_command(s->card, &request, response);
182 if (rlen < 0)
183 goto error;
184 if (s->cmd & PL181_CMD_RESPONSE) {
185 if (rlen == 0 || (rlen == 4 && (s->cmd & PL181_CMD_LONGRESP)))
186 goto error;
187 if (rlen != 4 && rlen != 16)
188 goto error;
189 s->response[0] = ldl_be_p(&response[0]);
190 if (rlen == 4) {
191 s->response[1] = s->response[2] = s->response[3] = 0;
192 } else {
193 s->response[1] = ldl_be_p(&response[4]);
194 s->response[2] = ldl_be_p(&response[8]);
195 s->response[3] = ldl_be_p(&response[12]) & ~1;
197 DPRINTF("Response received\n");
198 s->status |= PL181_STATUS_CMDRESPEND;
199 } else {
200 DPRINTF("Command sent\n");
201 s->status |= PL181_STATUS_CMDSENT;
203 return;
205 error:
206 DPRINTF("Timeout\n");
207 s->status |= PL181_STATUS_CMDTIMEOUT;
210 /* Transfer data between the card and the FIFO. This is complicated by
211 the FIFO holding 32-bit words and the card taking data in single byte
212 chunks. FIFO bytes are transferred in little-endian order. */
214 static void pl181_fifo_run(PL181State *s)
216 uint32_t bits;
217 uint32_t value = 0;
218 int n;
219 int is_read;
221 is_read = (s->datactrl & PL181_DATA_DIRECTION) != 0;
222 if (s->datacnt != 0 && (!is_read || sd_data_ready(s->card))
223 && !s->linux_hack) {
224 if (is_read) {
225 n = 0;
226 while (s->datacnt && s->fifo_len < PL181_FIFO_LEN) {
227 value |= (uint32_t)sd_read_data(s->card) << (n * 8);
228 s->datacnt--;
229 n++;
230 if (n == 4) {
231 pl181_fifo_push(s, value);
232 n = 0;
233 value = 0;
236 if (n != 0) {
237 pl181_fifo_push(s, value);
239 } else { /* write */
240 n = 0;
241 while (s->datacnt > 0 && (s->fifo_len > 0 || n > 0)) {
242 if (n == 0) {
243 value = pl181_fifo_pop(s);
244 n = 4;
246 n--;
247 s->datacnt--;
248 sd_write_data(s->card, value & 0xff);
249 value >>= 8;
253 s->status &= ~(PL181_STATUS_RX_FIFO | PL181_STATUS_TX_FIFO);
254 if (s->datacnt == 0) {
255 s->status |= PL181_STATUS_DATAEND;
256 /* HACK: */
257 s->status |= PL181_STATUS_DATABLOCKEND;
258 DPRINTF("Transfer Complete\n");
260 if (s->datacnt == 0 && s->fifo_len == 0) {
261 s->datactrl &= ~PL181_DATA_ENABLE;
262 DPRINTF("Data engine idle\n");
263 } else {
264 /* Update FIFO bits. */
265 bits = PL181_STATUS_TXACTIVE | PL181_STATUS_RXACTIVE;
266 if (s->fifo_len == 0) {
267 bits |= PL181_STATUS_TXFIFOEMPTY;
268 bits |= PL181_STATUS_RXFIFOEMPTY;
269 } else {
270 bits |= PL181_STATUS_TXDATAAVLBL;
271 bits |= PL181_STATUS_RXDATAAVLBL;
273 if (s->fifo_len == 16) {
274 bits |= PL181_STATUS_TXFIFOFULL;
275 bits |= PL181_STATUS_RXFIFOFULL;
277 if (s->fifo_len <= 8) {
278 bits |= PL181_STATUS_TXFIFOHALFEMPTY;
280 if (s->fifo_len >= 8) {
281 bits |= PL181_STATUS_RXFIFOHALFFULL;
283 if (s->datactrl & PL181_DATA_DIRECTION) {
284 bits &= PL181_STATUS_RX_FIFO;
285 } else {
286 bits &= PL181_STATUS_TX_FIFO;
288 s->status |= bits;
292 static uint64_t pl181_read(void *opaque, hwaddr offset,
293 unsigned size)
295 PL181State *s = (PL181State *)opaque;
296 uint32_t tmp;
298 if (offset >= 0xfe0 && offset < 0x1000) {
299 return pl181_id[(offset - 0xfe0) >> 2];
301 switch (offset) {
302 case 0x00: /* Power */
303 return s->power;
304 case 0x04: /* Clock */
305 return s->clock;
306 case 0x08: /* Argument */
307 return s->cmdarg;
308 case 0x0c: /* Command */
309 return s->cmd;
310 case 0x10: /* RespCmd */
311 return s->respcmd;
312 case 0x14: /* Response0 */
313 return s->response[0];
314 case 0x18: /* Response1 */
315 return s->response[1];
316 case 0x1c: /* Response2 */
317 return s->response[2];
318 case 0x20: /* Response3 */
319 return s->response[3];
320 case 0x24: /* DataTimer */
321 return s->datatimer;
322 case 0x28: /* DataLength */
323 return s->datalength;
324 case 0x2c: /* DataCtrl */
325 return s->datactrl;
326 case 0x30: /* DataCnt */
327 return s->datacnt;
328 case 0x34: /* Status */
329 tmp = s->status;
330 if (s->linux_hack) {
331 s->linux_hack = 0;
332 pl181_fifo_run(s);
333 pl181_update(s);
335 return tmp;
336 case 0x3c: /* Mask0 */
337 return s->mask[0];
338 case 0x40: /* Mask1 */
339 return s->mask[1];
340 case 0x48: /* FifoCnt */
341 /* The documentation is somewhat vague about exactly what FifoCnt
342 does. On real hardware it appears to be when decrememnted
343 when a word is transferred between the FIFO and the serial
344 data engine. DataCnt is decremented after each byte is
345 transferred between the serial engine and the card.
346 We don't emulate this level of detail, so both can be the same. */
347 tmp = (s->datacnt + 3) >> 2;
348 if (s->linux_hack) {
349 s->linux_hack = 0;
350 pl181_fifo_run(s);
351 pl181_update(s);
353 return tmp;
354 case 0x80: case 0x84: case 0x88: case 0x8c: /* FifoData */
355 case 0x90: case 0x94: case 0x98: case 0x9c:
356 case 0xa0: case 0xa4: case 0xa8: case 0xac:
357 case 0xb0: case 0xb4: case 0xb8: case 0xbc:
358 if (s->fifo_len == 0) {
359 qemu_log_mask(LOG_GUEST_ERROR, "pl181: Unexpected FIFO read\n");
360 return 0;
361 } else {
362 uint32_t value;
363 value = pl181_fifo_pop(s);
364 s->linux_hack = 1;
365 pl181_fifo_run(s);
366 pl181_update(s);
367 return value;
369 default:
370 qemu_log_mask(LOG_GUEST_ERROR,
371 "pl181_read: Bad offset %x\n", (int)offset);
372 return 0;
376 static void pl181_write(void *opaque, hwaddr offset,
377 uint64_t value, unsigned size)
379 PL181State *s = (PL181State *)opaque;
381 switch (offset) {
382 case 0x00: /* Power */
383 s->power = value & 0xff;
384 break;
385 case 0x04: /* Clock */
386 s->clock = value & 0xff;
387 break;
388 case 0x08: /* Argument */
389 s->cmdarg = value;
390 break;
391 case 0x0c: /* Command */
392 s->cmd = value;
393 if (s->cmd & PL181_CMD_ENABLE) {
394 if (s->cmd & PL181_CMD_INTERRUPT) {
395 qemu_log_mask(LOG_UNIMP,
396 "pl181: Interrupt mode not implemented\n");
397 } if (s->cmd & PL181_CMD_PENDING) {
398 qemu_log_mask(LOG_UNIMP,
399 "pl181: Pending commands not implemented\n");
400 } else {
401 pl181_send_command(s);
402 pl181_fifo_run(s);
404 /* The command has completed one way or the other. */
405 s->cmd &= ~PL181_CMD_ENABLE;
407 break;
408 case 0x24: /* DataTimer */
409 s->datatimer = value;
410 break;
411 case 0x28: /* DataLength */
412 s->datalength = value & 0xffff;
413 break;
414 case 0x2c: /* DataCtrl */
415 s->datactrl = value & 0xff;
416 if (value & PL181_DATA_ENABLE) {
417 s->datacnt = s->datalength;
418 pl181_fifo_run(s);
420 break;
421 case 0x38: /* Clear */
422 s->status &= ~(value & 0x7ff);
423 break;
424 case 0x3c: /* Mask0 */
425 s->mask[0] = value;
426 break;
427 case 0x40: /* Mask1 */
428 s->mask[1] = value;
429 break;
430 case 0x80: case 0x84: case 0x88: case 0x8c: /* FifoData */
431 case 0x90: case 0x94: case 0x98: case 0x9c:
432 case 0xa0: case 0xa4: case 0xa8: case 0xac:
433 case 0xb0: case 0xb4: case 0xb8: case 0xbc:
434 if (s->datacnt == 0) {
435 qemu_log_mask(LOG_GUEST_ERROR, "pl181: Unexpected FIFO write\n");
436 } else {
437 pl181_fifo_push(s, value);
438 pl181_fifo_run(s);
440 break;
441 default:
442 qemu_log_mask(LOG_GUEST_ERROR,
443 "pl181_write: Bad offset %x\n", (int)offset);
445 pl181_update(s);
448 static const MemoryRegionOps pl181_ops = {
449 .read = pl181_read,
450 .write = pl181_write,
451 .endianness = DEVICE_NATIVE_ENDIAN,
454 static void pl181_reset(DeviceState *d)
456 PL181State *s = PL181(d);
458 s->power = 0;
459 s->cmdarg = 0;
460 s->cmd = 0;
461 s->datatimer = 0;
462 s->datalength = 0;
463 s->respcmd = 0;
464 s->response[0] = 0;
465 s->response[1] = 0;
466 s->response[2] = 0;
467 s->response[3] = 0;
468 s->datatimer = 0;
469 s->datalength = 0;
470 s->datactrl = 0;
471 s->datacnt = 0;
472 s->status = 0;
473 s->linux_hack = 0;
474 s->mask[0] = 0;
475 s->mask[1] = 0;
477 /* We can assume our GPIO outputs have been wired up now */
478 sd_set_cb(s->card, s->cardstatus[0], s->cardstatus[1]);
479 /* Since we're still using the legacy SD API the card is not plugged
480 * into any bus, and we must reset it manually.
482 device_reset(DEVICE(s->card));
485 static void pl181_init(Object *obj)
487 DeviceState *dev = DEVICE(obj);
488 PL181State *s = PL181(obj);
489 SysBusDevice *sbd = SYS_BUS_DEVICE(obj);
491 memory_region_init_io(&s->iomem, obj, &pl181_ops, s, "pl181", 0x1000);
492 sysbus_init_mmio(sbd, &s->iomem);
493 sysbus_init_irq(sbd, &s->irq[0]);
494 sysbus_init_irq(sbd, &s->irq[1]);
495 qdev_init_gpio_out(dev, s->cardstatus, 2);
498 static void pl181_realize(DeviceState *dev, Error **errp)
500 PL181State *s = PL181(dev);
501 DriveInfo *dinfo;
503 /* FIXME use a qdev drive property instead of drive_get_next() */
504 dinfo = drive_get_next(IF_SD);
505 s->card = sd_init(dinfo ? blk_by_legacy_dinfo(dinfo) : NULL, false);
506 if (s->card == NULL) {
507 error_setg(errp, "sd_init failed");
511 static void pl181_class_init(ObjectClass *klass, void *data)
513 DeviceClass *k = DEVICE_CLASS(klass);
515 k->vmsd = &vmstate_pl181;
516 k->reset = pl181_reset;
517 /* Reason: init() method uses drive_get_next() */
518 k->user_creatable = false;
519 k->realize = pl181_realize;
522 static const TypeInfo pl181_info = {
523 .name = TYPE_PL181,
524 .parent = TYPE_SYS_BUS_DEVICE,
525 .instance_size = sizeof(PL181State),
526 .instance_init = pl181_init,
527 .class_init = pl181_class_init,
530 static void pl181_register_types(void)
532 type_register_static(&pl181_info);
535 type_init(pl181_register_types)