virtio-serial-bus: Unset guest_connected at reset and driver reset

[qemu/ar7.git] / hw / sm501.c

/*
 * QEMU SM501 Device
 *
 * Copyright (c) 2008 Shin-ichiro KAWASAKI
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy
 * of this software and associated documentation files (the "Software"), to deal
 * in the Software without restriction, including without limitation the rights
 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
 * copies of the Software, and to permit persons to whom the Software is
 * furnished to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in
 * all copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
 * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
 * THE SOFTWARE.
 */

#include <stdio.h>
#include "hw.h"
#include "pc.h"
#include "console.h"
#include "devices.h"
#include "sysbus.h"
#include "qdev-addr.h"
#include "range.h"

/*
 * Status: 2010/05/07
 *   - Minimum implementation for Linux console : mmio regs and CRT layer.
 *   - 2D grapihcs acceleration partially supported : only fill rectangle.
 *
 * TODO:
 *   - Panel support
 *   - Touch panel support
 *   - USB support
 *   - UART support
 *   - More 2D graphics engine support
 *   - Performance tuning
 */

//#define DEBUG_SM501
//#define DEBUG_BITBLT

#ifdef DEBUG_SM501
#define SM501_DPRINTF(fmt, ...) printf(fmt, ## __VA_ARGS__)
#else
#define SM501_DPRINTF(fmt, ...) do {} while(0)
#endif


#define MMIO_BASE_OFFSET 0x3e00000

/* SM501 register definitions taken from "linux/include/linux/sm501-regs.h" */

/* System Configuration area */
/* System config base */
#define SM501_SYS_CONFIG                (0x000000)

/* config 1 */
#define SM501_SYSTEM_CONTROL            (0x000000)

#define SM501_SYSCTRL_PANEL_TRISTATE    (1<<0)
#define SM501_SYSCTRL_MEM_TRISTATE      (1<<1)
#define SM501_SYSCTRL_CRT_TRISTATE      (1<<2)

#define SM501_SYSCTRL_PCI_SLAVE_BURST_MASK (3<<4)
#define SM501_SYSCTRL_PCI_SLAVE_BURST_1 (0<<4)
#define SM501_SYSCTRL_PCI_SLAVE_BURST_2 (1<<4)
#define SM501_SYSCTRL_PCI_SLAVE_BURST_4 (2<<4)
#define SM501_SYSCTRL_PCI_SLAVE_BURST_8 (3<<4)

#define SM501_SYSCTRL_PCI_CLOCK_RUN_EN  (1<<6)
#define SM501_SYSCTRL_PCI_RETRY_DISABLE (1<<7)
#define SM501_SYSCTRL_PCI_SUBSYS_LOCK   (1<<11)
#define SM501_SYSCTRL_PCI_BURST_READ_EN (1<<15)

/* miscellaneous control */

#define SM501_MISC_CONTROL              (0x000004)

#define SM501_MISC_BUS_SH               (0x0)
#define SM501_MISC_BUS_PCI              (0x1)
#define SM501_MISC_BUS_XSCALE           (0x2)
#define SM501_MISC_BUS_NEC              (0x6)
#define SM501_MISC_BUS_MASK             (0x7)

#define SM501_MISC_VR_62MB              (1<<3)
#define SM501_MISC_CDR_RESET            (1<<7)
#define SM501_MISC_USB_LB               (1<<8)
#define SM501_MISC_USB_SLAVE            (1<<9)
#define SM501_MISC_BL_1                 (1<<10)
#define SM501_MISC_MC                   (1<<11)
#define SM501_MISC_DAC_POWER            (1<<12)
#define SM501_MISC_IRQ_INVERT           (1<<16)
#define SM501_MISC_SH                   (1<<17)

#define SM501_MISC_HOLD_EMPTY           (0<<18)
#define SM501_MISC_HOLD_8               (1<<18)
#define SM501_MISC_HOLD_16              (2<<18)
#define SM501_MISC_HOLD_24              (3<<18)
#define SM501_MISC_HOLD_32              (4<<18)
#define SM501_MISC_HOLD_MASK            (7<<18)

#define SM501_MISC_FREQ_12              (1<<24)
#define SM501_MISC_PNL_24BIT            (1<<25)
#define SM501_MISC_8051_LE              (1<<26)



#define SM501_GPIO31_0_CONTROL          (0x000008)
#define SM501_GPIO63_32_CONTROL         (0x00000C)
#define SM501_DRAM_CONTROL              (0x000010)

/* command list */
#define SM501_ARBTRTN_CONTROL           (0x000014)

/* command list */
#define SM501_COMMAND_LIST_STATUS       (0x000024)

/* interrupt debug */
#define SM501_RAW_IRQ_STATUS            (0x000028)
#define SM501_RAW_IRQ_CLEAR             (0x000028)
#define SM501_IRQ_STATUS                (0x00002C)
#define SM501_IRQ_MASK                  (0x000030)
#define SM501_DEBUG_CONTROL             (0x000034)

/* power management */
#define SM501_POWERMODE_P2X_SRC         (1<<29)
#define SM501_POWERMODE_V2X_SRC         (1<<20)
#define SM501_POWERMODE_M_SRC           (1<<12)
#define SM501_POWERMODE_M1_SRC          (1<<4)

#define SM501_CURRENT_GATE              (0x000038)
#define SM501_CURRENT_CLOCK             (0x00003C)
#define SM501_POWER_MODE_0_GATE         (0x000040)
#define SM501_POWER_MODE_0_CLOCK        (0x000044)
#define SM501_POWER_MODE_1_GATE         (0x000048)
#define SM501_POWER_MODE_1_CLOCK        (0x00004C)
#define SM501_SLEEP_MODE_GATE           (0x000050)
#define SM501_POWER_MODE_CONTROL        (0x000054)

/* power gates for units within the 501 */
#define SM501_GATE_HOST                 (0)
#define SM501_GATE_MEMORY               (1)
#define SM501_GATE_DISPLAY              (2)
#define SM501_GATE_2D_ENGINE            (3)
#define SM501_GATE_CSC                  (4)
#define SM501_GATE_ZVPORT               (5)
#define SM501_GATE_GPIO                 (6)
#define SM501_GATE_UART0                (7)
#define SM501_GATE_UART1                (8)
#define SM501_GATE_SSP                  (10)
#define SM501_GATE_USB_HOST             (11)
#define SM501_GATE_USB_GADGET           (12)
#define SM501_GATE_UCONTROLLER          (17)
#define SM501_GATE_AC97                 (18)

/* panel clock */
#define SM501_CLOCK_P2XCLK              (24)
/* crt clock */
#define SM501_CLOCK_V2XCLK              (16)
/* main clock */
#define SM501_CLOCK_MCLK                (8)
/* SDRAM controller clock */
#define SM501_CLOCK_M1XCLK              (0)

/* config 2 */
#define SM501_PCI_MASTER_BASE           (0x000058)
#define SM501_ENDIAN_CONTROL            (0x00005C)
#define SM501_DEVICEID                  (0x000060)
/* 0x050100A0 */

#define SM501_DEVICEID_SM501            (0x05010000)
#define SM501_DEVICEID_IDMASK           (0xffff0000)
#define SM501_DEVICEID_REVMASK          (0x000000ff)

#define SM501_PLLCLOCK_COUNT            (0x000064)
#define SM501_MISC_TIMING               (0x000068)
#define SM501_CURRENT_SDRAM_CLOCK       (0x00006C)

#define SM501_PROGRAMMABLE_PLL_CONTROL  (0x000074)

/* GPIO base */
#define SM501_GPIO                      (0x010000)
#define SM501_GPIO_DATA_LOW             (0x00)
#define SM501_GPIO_DATA_HIGH            (0x04)
#define SM501_GPIO_DDR_LOW              (0x08)
#define SM501_GPIO_DDR_HIGH             (0x0C)
#define SM501_GPIO_IRQ_SETUP            (0x10)
#define SM501_GPIO_IRQ_STATUS           (0x14)
#define SM501_GPIO_IRQ_RESET            (0x14)

/* I2C controller base */
#define SM501_I2C                       (0x010040)
#define SM501_I2C_BYTE_COUNT            (0x00)
#define SM501_I2C_CONTROL               (0x01)
#define SM501_I2C_STATUS                (0x02)
#define SM501_I2C_RESET                 (0x02)
#define SM501_I2C_SLAVE_ADDRESS         (0x03)
#define SM501_I2C_DATA                  (0x04)

/* SSP base */
#define SM501_SSP                       (0x020000)

/* Uart 0 base */
#define SM501_UART0                     (0x030000)

/* Uart 1 base */
#define SM501_UART1                     (0x030020)

/* USB host port base */
#define SM501_USB_HOST                  (0x040000)

/* USB slave/gadget base */
#define SM501_USB_GADGET                (0x060000)

/* USB slave/gadget data port base */
#define SM501_USB_GADGET_DATA           (0x070000)

/* Display controller/video engine base */
#define SM501_DC                        (0x080000)

/* common defines for the SM501 address registers */
#define SM501_ADDR_FLIP                 (1<<31)
#define SM501_ADDR_EXT                  (1<<27)
#define SM501_ADDR_CS1                  (1<<26)
#define SM501_ADDR_MASK                 (0x3f << 26)

#define SM501_FIFO_MASK                 (0x3 << 16)
#define SM501_FIFO_1                    (0x0 << 16)
#define SM501_FIFO_3                    (0x1 << 16)
#define SM501_FIFO_7                    (0x2 << 16)
#define SM501_FIFO_11                   (0x3 << 16)

/* common registers for panel and the crt */
#define SM501_OFF_DC_H_TOT              (0x000)
#define SM501_OFF_DC_V_TOT              (0x008)
#define SM501_OFF_DC_H_SYNC             (0x004)
#define SM501_OFF_DC_V_SYNC             (0x00C)

#define SM501_DC_PANEL_CONTROL          (0x000)

#define SM501_DC_PANEL_CONTROL_FPEN     (1<<27)
#define SM501_DC_PANEL_CONTROL_BIAS     (1<<26)
#define SM501_DC_PANEL_CONTROL_DATA     (1<<25)
#define SM501_DC_PANEL_CONTROL_VDD      (1<<24)
#define SM501_DC_PANEL_CONTROL_DP       (1<<23)

#define SM501_DC_PANEL_CONTROL_TFT_888  (0<<21)
#define SM501_DC_PANEL_CONTROL_TFT_333  (1<<21)
#define SM501_DC_PANEL_CONTROL_TFT_444  (2<<21)

#define SM501_DC_PANEL_CONTROL_DE       (1<<20)

#define SM501_DC_PANEL_CONTROL_LCD_TFT  (0<<18)
#define SM501_DC_PANEL_CONTROL_LCD_STN8 (1<<18)
#define SM501_DC_PANEL_CONTROL_LCD_STN12 (2<<18)

#define SM501_DC_PANEL_CONTROL_CP       (1<<14)
#define SM501_DC_PANEL_CONTROL_VSP      (1<<13)
#define SM501_DC_PANEL_CONTROL_HSP      (1<<12)
#define SM501_DC_PANEL_CONTROL_CK       (1<<9)
#define SM501_DC_PANEL_CONTROL_TE       (1<<8)
#define SM501_DC_PANEL_CONTROL_VPD      (1<<7)
#define SM501_DC_PANEL_CONTROL_VP       (1<<6)
#define SM501_DC_PANEL_CONTROL_HPD      (1<<5)
#define SM501_DC_PANEL_CONTROL_HP       (1<<4)
#define SM501_DC_PANEL_CONTROL_GAMMA    (1<<3)
#define SM501_DC_PANEL_CONTROL_EN       (1<<2)

#define SM501_DC_PANEL_CONTROL_8BPP     (0<<0)
#define SM501_DC_PANEL_CONTROL_16BPP    (1<<0)
#define SM501_DC_PANEL_CONTROL_32BPP    (2<<0)


#define SM501_DC_PANEL_PANNING_CONTROL  (0x004)
#define SM501_DC_PANEL_COLOR_KEY        (0x008)
#define SM501_DC_PANEL_FB_ADDR          (0x00C)
#define SM501_DC_PANEL_FB_OFFSET        (0x010)
#define SM501_DC_PANEL_FB_WIDTH         (0x014)
#define SM501_DC_PANEL_FB_HEIGHT        (0x018)
#define SM501_DC_PANEL_TL_LOC           (0x01C)
#define SM501_DC_PANEL_BR_LOC           (0x020)
#define SM501_DC_PANEL_H_TOT            (0x024)
#define SM501_DC_PANEL_H_SYNC           (0x028)
#define SM501_DC_PANEL_V_TOT            (0x02C)
#define SM501_DC_PANEL_V_SYNC           (0x030)
#define SM501_DC_PANEL_CUR_LINE         (0x034)

#define SM501_DC_VIDEO_CONTROL          (0x040)
#define SM501_DC_VIDEO_FB0_ADDR         (0x044)
#define SM501_DC_VIDEO_FB_WIDTH         (0x048)
#define SM501_DC_VIDEO_FB0_LAST_ADDR    (0x04C)
#define SM501_DC_VIDEO_TL_LOC           (0x050)
#define SM501_DC_VIDEO_BR_LOC           (0x054)
#define SM501_DC_VIDEO_SCALE            (0x058)
#define SM501_DC_VIDEO_INIT_SCALE       (0x05C)
#define SM501_DC_VIDEO_YUV_CONSTANTS    (0x060)
#define SM501_DC_VIDEO_FB1_ADDR         (0x064)
#define SM501_DC_VIDEO_FB1_LAST_ADDR    (0x068)

#define SM501_DC_VIDEO_ALPHA_CONTROL    (0x080)
#define SM501_DC_VIDEO_ALPHA_FB_ADDR    (0x084)
#define SM501_DC_VIDEO_ALPHA_FB_OFFSET  (0x088)
#define SM501_DC_VIDEO_ALPHA_FB_LAST_ADDR       (0x08C)
#define SM501_DC_VIDEO_ALPHA_TL_LOC     (0x090)
#define SM501_DC_VIDEO_ALPHA_BR_LOC     (0x094)
#define SM501_DC_VIDEO_ALPHA_SCALE      (0x098)
#define SM501_DC_VIDEO_ALPHA_INIT_SCALE (0x09C)
#define SM501_DC_VIDEO_ALPHA_CHROMA_KEY (0x0A0)
#define SM501_DC_VIDEO_ALPHA_COLOR_LOOKUP       (0x0A4)

#define SM501_DC_PANEL_HWC_BASE         (0x0F0)
#define SM501_DC_PANEL_HWC_ADDR         (0x0F0)
#define SM501_DC_PANEL_HWC_LOC          (0x0F4)
#define SM501_DC_PANEL_HWC_COLOR_1_2    (0x0F8)
#define SM501_DC_PANEL_HWC_COLOR_3      (0x0FC)

#define SM501_HWC_EN                    (1<<31)

#define SM501_OFF_HWC_ADDR              (0x00)
#define SM501_OFF_HWC_LOC               (0x04)
#define SM501_OFF_HWC_COLOR_1_2         (0x08)
#define SM501_OFF_HWC_COLOR_3           (0x0C)

#define SM501_DC_ALPHA_CONTROL          (0x100)
#define SM501_DC_ALPHA_FB_ADDR          (0x104)
#define SM501_DC_ALPHA_FB_OFFSET        (0x108)
#define SM501_DC_ALPHA_TL_LOC           (0x10C)
#define SM501_DC_ALPHA_BR_LOC           (0x110)
#define SM501_DC_ALPHA_CHROMA_KEY       (0x114)
#define SM501_DC_ALPHA_COLOR_LOOKUP     (0x118)

#define SM501_DC_CRT_CONTROL            (0x200)

#define SM501_DC_CRT_CONTROL_TVP        (1<<15)
#define SM501_DC_CRT_CONTROL_CP         (1<<14)
#define SM501_DC_CRT_CONTROL_VSP        (1<<13)
#define SM501_DC_CRT_CONTROL_HSP        (1<<12)
#define SM501_DC_CRT_CONTROL_VS         (1<<11)
#define SM501_DC_CRT_CONTROL_BLANK      (1<<10)
#define SM501_DC_CRT_CONTROL_SEL        (1<<9)
#define SM501_DC_CRT_CONTROL_TE         (1<<8)
#define SM501_DC_CRT_CONTROL_PIXEL_MASK (0xF << 4)
#define SM501_DC_CRT_CONTROL_GAMMA      (1<<3)
#define SM501_DC_CRT_CONTROL_ENABLE     (1<<2)

#define SM501_DC_CRT_CONTROL_8BPP       (0<<0)
#define SM501_DC_CRT_CONTROL_16BPP      (1<<0)
#define SM501_DC_CRT_CONTROL_32BPP      (2<<0)

#define SM501_DC_CRT_FB_ADDR            (0x204)
#define SM501_DC_CRT_FB_OFFSET          (0x208)
#define SM501_DC_CRT_H_TOT              (0x20C)
#define SM501_DC_CRT_H_SYNC             (0x210)
#define SM501_DC_CRT_V_TOT              (0x214)
#define SM501_DC_CRT_V_SYNC             (0x218)
#define SM501_DC_CRT_SIGNATURE_ANALYZER (0x21C)
#define SM501_DC_CRT_CUR_LINE           (0x220)
#define SM501_DC_CRT_MONITOR_DETECT     (0x224)

#define SM501_DC_CRT_HWC_BASE           (0x230)
#define SM501_DC_CRT_HWC_ADDR           (0x230)
#define SM501_DC_CRT_HWC_LOC            (0x234)
#define SM501_DC_CRT_HWC_COLOR_1_2      (0x238)
#define SM501_DC_CRT_HWC_COLOR_3        (0x23C)

#define SM501_DC_PANEL_PALETTE          (0x400)

#define SM501_DC_VIDEO_PALETTE          (0x800)

#define SM501_DC_CRT_PALETTE            (0xC00)

/* Zoom Video port base */
#define SM501_ZVPORT                    (0x090000)

/* AC97/I2S base */
#define SM501_AC97                      (0x0A0000)

/* 8051 micro controller base */
#define SM501_UCONTROLLER               (0x0B0000)

/* 8051 micro controller SRAM base */
#define SM501_UCONTROLLER_SRAM          (0x0C0000)

/* DMA base */
#define SM501_DMA                       (0x0D0000)

/* 2d engine base */
#define SM501_2D_ENGINE                 (0x100000)
#define SM501_2D_SOURCE                 (0x00)
#define SM501_2D_DESTINATION            (0x04)
#define SM501_2D_DIMENSION              (0x08)
#define SM501_2D_CONTROL                (0x0C)
#define SM501_2D_PITCH                  (0x10)
#define SM501_2D_FOREGROUND             (0x14)
#define SM501_2D_BACKGROUND             (0x18)
#define SM501_2D_STRETCH                (0x1C)
#define SM501_2D_COLOR_COMPARE          (0x20)
#define SM501_2D_COLOR_COMPARE_MASK     (0x24)
#define SM501_2D_MASK                   (0x28)
#define SM501_2D_CLIP_TL                (0x2C)
#define SM501_2D_CLIP_BR                (0x30)
#define SM501_2D_MONO_PATTERN_LOW       (0x34)
#define SM501_2D_MONO_PATTERN_HIGH      (0x38)
#define SM501_2D_WINDOW_WIDTH           (0x3C)
#define SM501_2D_SOURCE_BASE            (0x40)
#define SM501_2D_DESTINATION_BASE       (0x44)
#define SM501_2D_ALPHA                  (0x48)
#define SM501_2D_WRAP                   (0x4C)
#define SM501_2D_STATUS                 (0x50)

#define SM501_CSC_Y_SOURCE_BASE         (0xC8)
#define SM501_CSC_CONSTANTS             (0xCC)
#define SM501_CSC_Y_SOURCE_X            (0xD0)
#define SM501_CSC_Y_SOURCE_Y            (0xD4)
#define SM501_CSC_U_SOURCE_BASE         (0xD8)
#define SM501_CSC_V_SOURCE_BASE         (0xDC)
#define SM501_CSC_SOURCE_DIMENSION      (0xE0)
#define SM501_CSC_SOURCE_PITCH          (0xE4)
#define SM501_CSC_DESTINATION           (0xE8)
#define SM501_CSC_DESTINATION_DIMENSION (0xEC)
#define SM501_CSC_DESTINATION_PITCH     (0xF0)
#define SM501_CSC_SCALE_FACTOR          (0xF4)
#define SM501_CSC_DESTINATION_BASE      (0xF8)
#define SM501_CSC_CONTROL               (0xFC)

/* 2d engine data port base */
#define SM501_2D_ENGINE_DATA            (0x110000)

/* end of register definitions */

#define SM501_HWC_WIDTH                       (64)
#define SM501_HWC_HEIGHT                      (64)

/* SM501 local memory size taken from "linux/drivers/mfd/sm501.c" */
static const uint32_t sm501_mem_local_size[] = {
        [0]     = 4*1024*1024,
        [1]     = 8*1024*1024,
        [2]     = 16*1024*1024,
        [3]     = 32*1024*1024,
        [4]     = 64*1024*1024,
        [5]     = 2*1024*1024,
};
#define get_local_mem_size(s) sm501_mem_local_size[(s)->local_mem_size_index]

typedef struct SM501State {
    /* graphic console status */
    DisplayState *ds;

    /* status & internal resources */
    target_phys_addr_t base;
    uint32_t local_mem_size_index;
    uint8_t * local_mem;
    MemoryRegion local_mem_region;
    uint32_t last_width;
    uint32_t last_height;

    /* mmio registers */
    uint32_t system_control;
    uint32_t misc_control;
    uint32_t gpio_31_0_control;
    uint32_t gpio_63_32_control;
    uint32_t dram_control;
    uint32_t irq_mask;
    uint32_t misc_timing;
    uint32_t power_mode_control;

    uint32_t uart0_ier;
    uint32_t uart0_lcr;
    uint32_t uart0_mcr;
    uint32_t uart0_scr;

    uint8_t dc_palette[0x400 * 3];

    uint32_t dc_panel_control;
    uint32_t dc_panel_panning_control;
    uint32_t dc_panel_fb_addr;
    uint32_t dc_panel_fb_offset;
    uint32_t dc_panel_fb_width;
    uint32_t dc_panel_fb_height;
    uint32_t dc_panel_tl_location;
    uint32_t dc_panel_br_location;
    uint32_t dc_panel_h_total;
    uint32_t dc_panel_h_sync;
    uint32_t dc_panel_v_total;
    uint32_t dc_panel_v_sync;

    uint32_t dc_panel_hwc_addr;
    uint32_t dc_panel_hwc_location;
    uint32_t dc_panel_hwc_color_1_2;
    uint32_t dc_panel_hwc_color_3;

    uint32_t dc_crt_control;
    uint32_t dc_crt_fb_addr;
    uint32_t dc_crt_fb_offset;
    uint32_t dc_crt_h_total;
    uint32_t dc_crt_h_sync;
    uint32_t dc_crt_v_total;
    uint32_t dc_crt_v_sync;

    uint32_t dc_crt_hwc_addr;
    uint32_t dc_crt_hwc_location;
    uint32_t dc_crt_hwc_color_1_2;
    uint32_t dc_crt_hwc_color_3;

    uint32_t twoD_source;
    uint32_t twoD_destination;
    uint32_t twoD_dimension;
    uint32_t twoD_control;
    uint32_t twoD_pitch;
    uint32_t twoD_foreground;
    uint32_t twoD_stretch;
    uint32_t twoD_color_compare_mask;
    uint32_t twoD_mask;
    uint32_t twoD_window_width;
    uint32_t twoD_source_base;
    uint32_t twoD_destination_base;

} SM501State;

static uint32_t get_local_mem_size_index(uint32_t size)
{
    uint32_t norm_size = 0;
    int i, index = 0;

    for (i = 0; i < ARRAY_SIZE(sm501_mem_local_size); i++) {
        uint32_t new_size = sm501_mem_local_size[i];
        if (new_size >= size) {
            if (norm_size == 0 || norm_size > new_size) {
                norm_size = new_size;
                index = i;
            }
        }
    }

    return index;
}

/**
 * Check the availability of hardware cursor.
 * @param crt  0 for PANEL, 1 for CRT.
 */
static inline int is_hwc_enabled(SM501State *state, int crt)
{
    uint32_t addr = crt ? state->dc_crt_hwc_addr : state->dc_panel_hwc_addr;
    return addr & 0x80000000;
}

/**
 * Get the address which holds cursor pattern data.
 * @param crt  0 for PANEL, 1 for CRT.
 */
static inline uint32_t get_hwc_address(SM501State *state, int crt)
{
    uint32_t addr = crt ? state->dc_crt_hwc_addr : state->dc_panel_hwc_addr;
    return (addr & 0x03FFFFF0)/* >> 4*/;
}

/**
 * Get the cursor position in y coordinate.
 * @param crt  0 for PANEL, 1 for CRT.
 */
static inline uint32_t get_hwc_y(SM501State *state, int crt)
{
    uint32_t location = crt ? state->dc_crt_hwc_location
                            : state->dc_panel_hwc_location;
    return (location & 0x07FF0000) >> 16;
}

/**
 * Get the cursor position in x coordinate.
 * @param crt  0 for PANEL, 1 for CRT.
 */
static inline uint32_t get_hwc_x(SM501State *state, int crt)
{
    uint32_t location = crt ? state->dc_crt_hwc_location
                            : state->dc_panel_hwc_location;
    return location & 0x000007FF;
}

/**
 * Get the cursor position in x coordinate.
 * @param crt  0 for PANEL, 1 for CRT.
 * @param index  0, 1, 2 or 3 which specifies color of corsor dot.
 */
static inline uint16_t get_hwc_color(SM501State *state, int crt, int index)
{
    uint32_t color_reg = 0;
    uint16_t color_565 = 0;

    if (index == 0) {
        return 0;
    }

    switch (index) {
    case 1:
    case 2:
        color_reg = crt ? state->dc_crt_hwc_color_1_2
                        : state->dc_panel_hwc_color_1_2;
        break;
    case 3:
        color_reg = crt ? state->dc_crt_hwc_color_3
                        : state->dc_panel_hwc_color_3;
        break;
    default:
        printf("invalid hw cursor color.\n");
        abort();
    }

    switch (index) {
    case 1:
    case 3:
        color_565 = (uint16_t)(color_reg & 0xFFFF);
        break;
    case 2:
        color_565 = (uint16_t)((color_reg >> 16) & 0xFFFF);
        break;
    }
    return color_565;
}

static int within_hwc_y_range(SM501State *state, int y, int crt)
{
    int hwc_y = get_hwc_y(state, crt);
    return (hwc_y <= y && y < hwc_y + SM501_HWC_HEIGHT);
}

static void sm501_2d_operation(SM501State * s)
{
    /* obtain operation parameters */
    int operation = (s->twoD_control >> 16) & 0x1f;
    int rtl = s->twoD_control & 0x8000000;
    int src_x = (s->twoD_source >> 16) & 0x01FFF;
    int src_y = s->twoD_source & 0xFFFF;
    int dst_x = (s->twoD_destination >> 16) & 0x01FFF;
    int dst_y = s->twoD_destination & 0xFFFF;
    int operation_width = (s->twoD_dimension >> 16) & 0x1FFF;
    int operation_height = s->twoD_dimension & 0xFFFF;
    uint32_t color = s->twoD_foreground;
    int format_flags = (s->twoD_stretch >> 20) & 0x3;
    int addressing = (s->twoD_stretch >> 16) & 0xF;

    /* get frame buffer info */
    uint8_t * src = s->local_mem + (s->twoD_source_base & 0x03FFFFFF);
    uint8_t * dst = s->local_mem + (s->twoD_destination_base & 0x03FFFFFF);
    int src_width = (s->dc_crt_h_total & 0x00000FFF) + 1;
    int dst_width = (s->dc_crt_h_total & 0x00000FFF) + 1;

    if (addressing != 0x0) {
        printf("%s: only XY addressing is supported.\n", __func__);
        abort();
    }

    if ((s->twoD_source_base & 0x08000000) ||
        (s->twoD_destination_base & 0x08000000)) {
        printf("%s: only local memory is supported.\n", __func__);
        abort();
    }

    switch (operation) {
    case 0x00: /* copy area */
#define COPY_AREA(_bpp, _pixel_type, rtl) {                                 \
        int y, x, index_d, index_s;                                         \
        for (y = 0; y < operation_height; y++) {                            \
            for (x = 0; x < operation_width; x++) {                         \
                if (rtl) {                                                  \
                    index_s = ((src_y - y) * src_width + src_x - x) * _bpp; \
                    index_d = ((dst_y - y) * dst_width + dst_x - x) * _bpp; \
                } else {                                                    \
                    index_s = ((src_y + y) * src_width + src_x + x) * _bpp; \
                    index_d = ((dst_y + y) * dst_width + dst_x + x) * _bpp; \
                }                                                           \
                *(_pixel_type*)&dst[index_d] = *(_pixel_type*)&src[index_s];\
            }                                                               \
        }                                                                   \
    }
        switch (format_flags) {
        case 0:
            COPY_AREA(1, uint8_t, rtl);
            break;
        case 1:
            COPY_AREA(2, uint16_t, rtl);
            break;
        case 2:
            COPY_AREA(4, uint32_t, rtl);
            break;
        }
        break;

    case 0x01: /* fill rectangle */
#define FILL_RECT(_bpp, _pixel_type) {                                      \
        int y, x;                                                           \
        for (y = 0; y < operation_height; y++) {                            \
            for (x = 0; x < operation_width; x++) {                         \
                int index = ((dst_y + y) * dst_width + dst_x + x) * _bpp;   \
                *(_pixel_type*)&dst[index] = (_pixel_type)color;            \
            }                                                               \
        }                                                                   \
    }

        switch (format_flags) {
        case 0:
            FILL_RECT(1, uint8_t);
            break;
        case 1:
            FILL_RECT(2, uint16_t);
            break;
        case 2:
            FILL_RECT(4, uint32_t);
            break;
        }
        break;

    default:
        printf("non-implemented SM501 2D operation. %d\n", operation);
        abort();
        break;
    }
}

static uint64_t sm501_system_config_read(void *opaque, target_phys_addr_t addr,
                                         unsigned size)
{
    SM501State * s = (SM501State *)opaque;
    uint32_t ret = 0;
    SM501_DPRINTF("sm501 system config regs : read addr=%x\n", (int)addr);

    switch(addr) {
    case SM501_SYSTEM_CONTROL:
        ret = s->system_control;
        break;
    case SM501_MISC_CONTROL:
        ret = s->misc_control;
        break;
    case SM501_GPIO31_0_CONTROL:
        ret = s->gpio_31_0_control;
        break;
    case SM501_GPIO63_32_CONTROL:
        ret = s->gpio_63_32_control;
        break;
    case SM501_DEVICEID:
        ret = 0x050100A0;
        break;
    case SM501_DRAM_CONTROL:
        ret = (s->dram_control & 0x07F107C0) | s->local_mem_size_index << 13;
        break;
    case SM501_IRQ_MASK:
        ret = s->irq_mask;
        break;
    case SM501_MISC_TIMING:
        /* TODO : simulate gate control */
        ret = s->misc_timing;
        break;
    case SM501_CURRENT_GATE:
        /* TODO : simulate gate control */
        ret = 0x00021807;
        break;
    case SM501_CURRENT_CLOCK:
        ret = 0x2A1A0A09;
        break;
    case SM501_POWER_MODE_CONTROL:
        ret = s->power_mode_control;
        break;

    default:
        printf("sm501 system config : not implemented register read."
               " addr=%x\n", (int)addr);
        abort();
    }

    return ret;
}

static void sm501_system_config_write(void *opaque, target_phys_addr_t addr,
                                      uint64_t value, unsigned size)
{
    SM501State * s = (SM501State *)opaque;
    SM501_DPRINTF("sm501 system config regs : write addr=%x, val=%x\n",
                  (uint32_t)addr, (uint32_t)value);

    switch(addr) {
    case SM501_SYSTEM_CONTROL:
        s->system_control = value & 0xE300B8F7;
        break;
    case SM501_MISC_CONTROL:
        s->misc_control = value & 0xFF7FFF20;
        break;
    case SM501_GPIO31_0_CONTROL:
        s->gpio_31_0_control = value;
        break;
    case SM501_GPIO63_32_CONTROL:
        s->gpio_63_32_control = value;
        break;
    case SM501_DRAM_CONTROL:
        s->local_mem_size_index = (value >> 13) & 0x7;
        /* rODO : check validity of size change */
        s->dram_control |=  value & 0x7FFFFFC3;
        break;
    case SM501_IRQ_MASK:
        s->irq_mask = value;
        break;
    case SM501_MISC_TIMING:
        s->misc_timing = value & 0xF31F1FFF;
        break;
    case SM501_POWER_MODE_0_GATE:
    case SM501_POWER_MODE_1_GATE:
    case SM501_POWER_MODE_0_CLOCK:
    case SM501_POWER_MODE_1_CLOCK:
        /* TODO : simulate gate & clock control */
        break;
    case SM501_POWER_MODE_CONTROL:
        s->power_mode_control = value & 0x00000003;
        break;

    default:
        printf("sm501 system config : not implemented register write."
               " addr=%x, val=%x\n", (int)addr, (uint32_t)value);
        abort();
    }
}

static const MemoryRegionOps sm501_system_config_ops = {
    .read = sm501_system_config_read,
    .write = sm501_system_config_write,
    .valid = {
        .min_access_size = 4,
        .max_access_size = 4,
    },
    .endianness = DEVICE_NATIVE_ENDIAN,
};

static uint32_t sm501_palette_read(void *opaque, target_phys_addr_t addr)
{
    SM501State * s = (SM501State *)opaque;
    SM501_DPRINTF("sm501 palette read addr=%x\n", (int)addr);

    /* TODO : consider BYTE/WORD access */
    /* TODO : consider endian */

    assert(range_covers_byte(0, 0x400 * 3, addr));
    return *(uint32_t*)&s->dc_palette[addr];
}

static void sm501_palette_write(void *opaque,
                                target_phys_addr_t addr, uint32_t value)
{
    SM501State * s = (SM501State *)opaque;
    SM501_DPRINTF("sm501 palette write addr=%x, val=%x\n",
                  (int)addr, value);

    /* TODO : consider BYTE/WORD access */
    /* TODO : consider endian */

    assert(range_covers_byte(0, 0x400 * 3, addr));
    *(uint32_t*)&s->dc_palette[addr] = value;
}

static uint64_t sm501_disp_ctrl_read(void *opaque, target_phys_addr_t addr,
                                     unsigned size)
{
    SM501State * s = (SM501State *)opaque;
    uint32_t ret = 0;
    SM501_DPRINTF("sm501 disp ctrl regs : read addr=%x\n", (int)addr);

    switch(addr) {

    case SM501_DC_PANEL_CONTROL:
        ret = s->dc_panel_control;
        break;
    case SM501_DC_PANEL_PANNING_CONTROL:
        ret = s->dc_panel_panning_control;
        break;
    case SM501_DC_PANEL_FB_ADDR:
        ret = s->dc_panel_fb_addr;
        break;
    case SM501_DC_PANEL_FB_OFFSET:
        ret = s->dc_panel_fb_offset;
        break;
    case SM501_DC_PANEL_FB_WIDTH:
        ret = s->dc_panel_fb_width;
        break;
    case SM501_DC_PANEL_FB_HEIGHT:
        ret = s->dc_panel_fb_height;
        break;
    case SM501_DC_PANEL_TL_LOC:
        ret = s->dc_panel_tl_location;
        break;
    case SM501_DC_PANEL_BR_LOC:
        ret = s->dc_panel_br_location;
        break;

    case SM501_DC_PANEL_H_TOT:
        ret = s->dc_panel_h_total;
        break;
    case SM501_DC_PANEL_H_SYNC:
        ret = s->dc_panel_h_sync;
        break;
    case SM501_DC_PANEL_V_TOT:
        ret = s->dc_panel_v_total;
        break;
    case SM501_DC_PANEL_V_SYNC:
        ret = s->dc_panel_v_sync;
        break;

    case SM501_DC_CRT_CONTROL:
        ret = s->dc_crt_control;
        break;
    case SM501_DC_CRT_FB_ADDR:
        ret = s->dc_crt_fb_addr;
        break;
    case SM501_DC_CRT_FB_OFFSET:
        ret = s->dc_crt_fb_offset;
        break;
    case SM501_DC_CRT_H_TOT:
        ret = s->dc_crt_h_total;
        break;
    case SM501_DC_CRT_H_SYNC:
        ret = s->dc_crt_h_sync;
        break;
    case SM501_DC_CRT_V_TOT:
        ret = s->dc_crt_v_total;
        break;
    case SM501_DC_CRT_V_SYNC:
        ret = s->dc_crt_v_sync;
        break;

    case SM501_DC_CRT_HWC_ADDR:
        ret = s->dc_crt_hwc_addr;
        break;
    case SM501_DC_CRT_HWC_LOC:
        ret = s->dc_crt_hwc_location;
        break;
    case SM501_DC_CRT_HWC_COLOR_1_2:
        ret = s->dc_crt_hwc_color_1_2;
        break;
    case SM501_DC_CRT_HWC_COLOR_3:
        ret = s->dc_crt_hwc_color_3;
        break;

    case SM501_DC_PANEL_PALETTE ... SM501_DC_PANEL_PALETTE + 0x400*3 - 4:
        ret = sm501_palette_read(opaque, addr - SM501_DC_PANEL_PALETTE);
        break;

    default:
        printf("sm501 disp ctrl : not implemented register read."
               " addr=%x\n", (int)addr);
        abort();
    }

    return ret;
}

static void sm501_disp_ctrl_write(void *opaque, target_phys_addr_t addr,
                                  uint64_t value, unsigned size)
{
    SM501State * s = (SM501State *)opaque;
    SM501_DPRINTF("sm501 disp ctrl regs : write addr=%x, val=%x\n",
                  (unsigned)addr, (unsigned)value);

    switch(addr) {
    case SM501_DC_PANEL_CONTROL:
        s->dc_panel_control = value & 0x0FFF73FF;
        break;
    case SM501_DC_PANEL_PANNING_CONTROL:
        s->dc_panel_panning_control = value & 0xFF3FFF3F;
        break;
    case SM501_DC_PANEL_FB_ADDR:
        s->dc_panel_fb_addr = value & 0x8FFFFFF0;
        break;
    case SM501_DC_PANEL_FB_OFFSET:
        s->dc_panel_fb_offset = value & 0x3FF03FF0;
        break;
    case SM501_DC_PANEL_FB_WIDTH:
        s->dc_panel_fb_width = value & 0x0FFF0FFF;
        break;
    case SM501_DC_PANEL_FB_HEIGHT:
        s->dc_panel_fb_height = value & 0x0FFF0FFF;
        break;
    case SM501_DC_PANEL_TL_LOC:
        s->dc_panel_tl_location = value & 0x07FF07FF;
        break;
    case SM501_DC_PANEL_BR_LOC:
        s->dc_panel_br_location = value & 0x07FF07FF;
        break;

    case SM501_DC_PANEL_H_TOT:
        s->dc_panel_h_total = value & 0x0FFF0FFF;
        break;
    case SM501_DC_PANEL_H_SYNC:
        s->dc_panel_h_sync = value & 0x00FF0FFF;
        break;
    case SM501_DC_PANEL_V_TOT:
        s->dc_panel_v_total = value & 0x0FFF0FFF;
        break;
    case SM501_DC_PANEL_V_SYNC:
        s->dc_panel_v_sync = value & 0x003F0FFF;
        break;

    case SM501_DC_PANEL_HWC_ADDR:
        s->dc_panel_hwc_addr = value & 0x8FFFFFF0;
        break;
    case SM501_DC_PANEL_HWC_LOC:
        s->dc_panel_hwc_location = value & 0x0FFF0FFF;
        break;
    case SM501_DC_PANEL_HWC_COLOR_1_2:
        s->dc_panel_hwc_color_1_2 = value;
        break;
    case SM501_DC_PANEL_HWC_COLOR_3:
        s->dc_panel_hwc_color_3 = value & 0x0000FFFF;
        break;

    case SM501_DC_CRT_CONTROL:
        s->dc_crt_control = value & 0x0003FFFF;
        break;
    case SM501_DC_CRT_FB_ADDR:
        s->dc_crt_fb_addr = value & 0x8FFFFFF0;
        break;
    case SM501_DC_CRT_FB_OFFSET:
        s->dc_crt_fb_offset = value & 0x3FF03FF0;
        break;
    case SM501_DC_CRT_H_TOT:
        s->dc_crt_h_total = value & 0x0FFF0FFF;
        break;
    case SM501_DC_CRT_H_SYNC:
        s->dc_crt_h_sync = value & 0x00FF0FFF;
        break;
    case SM501_DC_CRT_V_TOT:
        s->dc_crt_v_total = value & 0x0FFF0FFF;
        break;
    case SM501_DC_CRT_V_SYNC:
        s->dc_crt_v_sync = value & 0x003F0FFF;
        break;

    case SM501_DC_CRT_HWC_ADDR:
        s->dc_crt_hwc_addr = value & 0x8FFFFFF0;
        break;
    case SM501_DC_CRT_HWC_LOC:
        s->dc_crt_hwc_location = value & 0x0FFF0FFF;
        break;
    case SM501_DC_CRT_HWC_COLOR_1_2:
        s->dc_crt_hwc_color_1_2 = value;
        break;
    case SM501_DC_CRT_HWC_COLOR_3:
        s->dc_crt_hwc_color_3 = value & 0x0000FFFF;
        break;

    case SM501_DC_PANEL_PALETTE ... SM501_DC_PANEL_PALETTE + 0x400*3 - 4:
        sm501_palette_write(opaque, addr - SM501_DC_PANEL_PALETTE, value);
        break;

    default:
        printf("sm501 disp ctrl : not implemented register write."
               " addr=%x, val=%x\n", (int)addr, (unsigned)value);
        abort();
    }
}

static const MemoryRegionOps sm501_disp_ctrl_ops = {
    .read = sm501_disp_ctrl_read,
    .write = sm501_disp_ctrl_write,
    .valid = {
        .min_access_size = 4,
        .max_access_size = 4,
    },
    .endianness = DEVICE_NATIVE_ENDIAN,
};

static uint64_t sm501_2d_engine_read(void *opaque, target_phys_addr_t addr,
                                     unsigned size)
{
    SM501State * s = (SM501State *)opaque;
    uint32_t ret = 0;
    SM501_DPRINTF("sm501 2d engine regs : read addr=%x\n", (int)addr);

    switch(addr) {
    case SM501_2D_SOURCE_BASE:
        ret = s->twoD_source_base;
        break;
    default:
        printf("sm501 disp ctrl : not implemented register read."
               " addr=%x\n", (int)addr);
        abort();
    }

    return ret;
}

static void sm501_2d_engine_write(void *opaque, target_phys_addr_t addr,
                                  uint64_t value, unsigned size)
{
    SM501State * s = (SM501State *)opaque;
    SM501_DPRINTF("sm501 2d engine regs : write addr=%x, val=%x\n",
                  (unsigned)addr, (unsigned)value);

    switch(addr) {
    case SM501_2D_SOURCE:
        s->twoD_source = value;
        break;
    case SM501_2D_DESTINATION:
        s->twoD_destination = value;
        break;
    case SM501_2D_DIMENSION:
        s->twoD_dimension = value;
        break;
    case SM501_2D_CONTROL:
        s->twoD_control = value;

        /* do 2d operation if start flag is set. */
        if (value & 0x80000000) {
            sm501_2d_operation(s);
            s->twoD_control &= ~0x80000000; /* start flag down */
        }

        break;
    case SM501_2D_PITCH:
        s->twoD_pitch = value;
        break;
    case SM501_2D_FOREGROUND:
        s->twoD_foreground = value;
        break;
    case SM501_2D_STRETCH:
        s->twoD_stretch = value;
        break;
    case SM501_2D_COLOR_COMPARE_MASK:
        s->twoD_color_compare_mask = value;
        break;
    case SM501_2D_MASK:
        s->twoD_mask = value;
        break;
    case SM501_2D_WINDOW_WIDTH:
        s->twoD_window_width = value;
        break;
    case SM501_2D_SOURCE_BASE:
        s->twoD_source_base = value;
        break;
    case SM501_2D_DESTINATION_BASE:
        s->twoD_destination_base = value;
        break;
    default:
        printf("sm501 2d engine : not implemented register write."
               " addr=%x, val=%x\n", (int)addr, (unsigned)value);
        abort();
    }
}

static const MemoryRegionOps sm501_2d_engine_ops = {
    .read = sm501_2d_engine_read,
    .write = sm501_2d_engine_write,
    .valid = {
        .min_access_size = 4,
        .max_access_size = 4,
    },
    .endianness = DEVICE_NATIVE_ENDIAN,
};

/* draw line functions for all console modes */

#include "pixel_ops.h"

typedef void draw_line_func(uint8_t *d, const uint8_t *s,
                            int width, const uint32_t *pal);

typedef void draw_hwc_line_func(SM501State * s, int crt, uint8_t * palette,
                                int c_y, uint8_t *d, int width);

#define DEPTH 8
#include "sm501_template.h"

#define DEPTH 15
#include "sm501_template.h"

#define BGR_FORMAT
#define DEPTH 15
#include "sm501_template.h"

#define DEPTH 16
#include "sm501_template.h"

#define BGR_FORMAT
#define DEPTH 16
#include "sm501_template.h"

#define DEPTH 32
#include "sm501_template.h"

#define BGR_FORMAT
#define DEPTH 32
#include "sm501_template.h"

static draw_line_func * draw_line8_funcs[] = {
    draw_line8_8,
    draw_line8_15,
    draw_line8_16,
    draw_line8_32,
    draw_line8_32bgr,
    draw_line8_15bgr,
    draw_line8_16bgr,
};

static draw_line_func * draw_line16_funcs[] = {
    draw_line16_8,
    draw_line16_15,
    draw_line16_16,
    draw_line16_32,
    draw_line16_32bgr,
    draw_line16_15bgr,
    draw_line16_16bgr,
};

static draw_line_func * draw_line32_funcs[] = {
    draw_line32_8,
    draw_line32_15,
    draw_line32_16,
    draw_line32_32,
    draw_line32_32bgr,
    draw_line32_15bgr,
    draw_line32_16bgr,
};

static draw_hwc_line_func * draw_hwc_line_funcs[] = {
    draw_hwc_line_8,
    draw_hwc_line_15,
    draw_hwc_line_16,
    draw_hwc_line_32,
    draw_hwc_line_32bgr,
    draw_hwc_line_15bgr,
    draw_hwc_line_16bgr,
};

static inline int get_depth_index(DisplayState *s)
{
    switch(ds_get_bits_per_pixel(s)) {
    default:
    case 8:
        return 0;
    case 15:
        return 1;
    case 16:
        return 2;
    case 32:
        if (is_surface_bgr(s->surface))
            return 4;
        else
            return 3;
    }
}

static void sm501_draw_crt(SM501State * s)
{
    int y;
    int width = (s->dc_crt_h_total & 0x00000FFF) + 1;
    int height = (s->dc_crt_v_total & 0x00000FFF) + 1;

    uint8_t  * src = s->local_mem;
    int src_bpp = 0;
    int dst_bpp = ds_get_bytes_per_pixel(s->ds) + (ds_get_bits_per_pixel(s->ds) % 8 ? 1 : 0);
    uint32_t * palette = (uint32_t *)&s->dc_palette[SM501_DC_CRT_PALETTE
                                                    - SM501_DC_PANEL_PALETTE];
    uint8_t hwc_palette[3 * 3];
    int ds_depth_index = get_depth_index(s->ds);
    draw_line_func * draw_line = NULL;
    draw_hwc_line_func * draw_hwc_line = NULL;
    int full_update = 0;
    int y_start = -1;
    ram_addr_t page_min = ~0l;
    ram_addr_t page_max = 0l;
    ram_addr_t offset = 0;

    /* choose draw_line function */
    switch (s->dc_crt_control & 3) {
    case SM501_DC_CRT_CONTROL_8BPP:
        src_bpp = 1;
        draw_line = draw_line8_funcs[ds_depth_index];
        break;
    case SM501_DC_CRT_CONTROL_16BPP:
        src_bpp = 2;
        draw_line = draw_line16_funcs[ds_depth_index];
        break;
    case SM501_DC_CRT_CONTROL_32BPP:
        src_bpp = 4;
        draw_line = draw_line32_funcs[ds_depth_index];
        break;
    default:
        printf("sm501 draw crt : invalid DC_CRT_CONTROL=%x.\n",
               s->dc_crt_control);
        abort();
        break;
    }

    /* set up to draw hardware cursor */
    if (is_hwc_enabled(s, 1)) {
        int i;

        /* get cursor palette */
        for (i = 0; i < 3; i++) {
            uint16_t rgb565 = get_hwc_color(s, 1, i + 1);
            hwc_palette[i * 3 + 0] = (rgb565 & 0xf800) >> 8; /* red */
            hwc_palette[i * 3 + 1] = (rgb565 & 0x07e0) >> 3; /* green */
            hwc_palette[i * 3 + 2] = (rgb565 & 0x001f) << 3; /* blue */
        }

        /* choose cursor draw line function */
        draw_hwc_line = draw_hwc_line_funcs[ds_depth_index];
    }

    /* adjust console size */
    if (s->last_width != width || s->last_height != height) {
        qemu_console_resize(s->ds, width, height);
        s->last_width = width;
        s->last_height = height;
        full_update = 1;
    }

    /* draw each line according to conditions */
    for (y = 0; y < height; y++) {
        int update_hwc = draw_hwc_line ? within_hwc_y_range(s, y, 1) : 0;
        int update = full_update || update_hwc;
        ram_addr_t page0 = offset;
        ram_addr_t page1 = offset + width * src_bpp - 1;

        /* check dirty flags for each line */
        update = memory_region_get_dirty(&s->local_mem_region, page0,
                                         page1 - page0, DIRTY_MEMORY_VGA);

        /* draw line and change status */
        if (update) {
            uint8_t * d = &(ds_get_data(s->ds)[y * width * dst_bpp]);

            /* draw graphics layer */
            draw_line(d, src, width, palette);

            /* draw haredware cursor */
            if (update_hwc) {
                draw_hwc_line(s, 1, hwc_palette, y - get_hwc_y(s, 1), d, width);
            }

            if (y_start < 0)
                y_start = y;
            if (page0 < page_min)
                page_min = page0;
            if (page1 > page_max)
                page_max = page1;
        } else {
            if (y_start >= 0) {
                /* flush to display */
                dpy_update(s->ds, 0, y_start, width, y - y_start);
                y_start = -1;
            }
        }

        src += width * src_bpp;
        offset += width * src_bpp;
    }

    /* complete flush to display */
    if (y_start >= 0)
        dpy_update(s->ds, 0, y_start, width, y - y_start);

    /* clear dirty flags */
    if (page_min != ~0l) {
        memory_region_reset_dirty(&s->local_mem_region,
                                  page_min, page_max + TARGET_PAGE_SIZE,
                                  DIRTY_MEMORY_VGA);
    }
}

static void sm501_update_display(void *opaque)
{
    SM501State * s = (SM501State *)opaque;

    if (s->dc_crt_control & SM501_DC_CRT_CONTROL_ENABLE)
        sm501_draw_crt(s);
}

void sm501_init(MemoryRegion *address_space_mem, uint32_t base,
                uint32_t local_mem_bytes, qemu_irq irq, CharDriverState *chr)
{
    SM501State * s;
    DeviceState *dev;
    MemoryRegion *sm501_system_config = g_new(MemoryRegion, 1);
    MemoryRegion *sm501_disp_ctrl = g_new(MemoryRegion, 1);
    MemoryRegion *sm501_2d_engine = g_new(MemoryRegion, 1);

    /* allocate management data region */
    s = (SM501State *)g_malloc0(sizeof(SM501State));
    s->base = base;
    s->local_mem_size_index
        = get_local_mem_size_index(local_mem_bytes);
    SM501_DPRINTF("local mem size=%x. index=%d\n", get_local_mem_size(s),
                  s->local_mem_size_index);
    s->system_control = 0x00100000;
    s->misc_control = 0x00001000; /* assumes SH, active=low */
    s->dc_panel_control = 0x00010000;
    s->dc_crt_control = 0x00010000;

    /* allocate local memory */
    memory_region_init_ram(&s->local_mem_region, "sm501.local",
                           local_mem_bytes);
    vmstate_register_ram_global(&s->local_mem_region);
    s->local_mem = memory_region_get_ram_ptr(&s->local_mem_region);
    memory_region_add_subregion(address_space_mem, base, &s->local_mem_region);

    /* map mmio */
    memory_region_init_io(sm501_system_config, &sm501_system_config_ops, s,
                          "sm501-system-config", 0x6c);
    memory_region_add_subregion(address_space_mem, base + MMIO_BASE_OFFSET,
                                sm501_system_config);
    memory_region_init_io(sm501_disp_ctrl, &sm501_disp_ctrl_ops, s,
                          "sm501-disp-ctrl", 0x1000);
    memory_region_add_subregion(address_space_mem,
                                base + MMIO_BASE_OFFSET + SM501_DC,
                                sm501_disp_ctrl);
    memory_region_init_io(sm501_2d_engine, &sm501_2d_engine_ops, s,
                          "sm501-2d-engine", 0x54);
    memory_region_add_subregion(address_space_mem,
                                base + MMIO_BASE_OFFSET + SM501_2D_ENGINE,
                                sm501_2d_engine);

    /* bridge to usb host emulation module */
    dev = qdev_create(NULL, "sysbus-ohci");
    qdev_prop_set_uint32(dev, "num-ports", 2);
    qdev_prop_set_taddr(dev, "dma-offset", base);
    qdev_init_nofail(dev);
    sysbus_mmio_map(sysbus_from_qdev(dev), 0,
                    base + MMIO_BASE_OFFSET + SM501_USB_HOST);
    sysbus_connect_irq(sysbus_from_qdev(dev), 0, irq);

    /* bridge to serial emulation module */
    if (chr) {
        serial_mm_init(address_space_mem,
                       base + MMIO_BASE_OFFSET + SM501_UART0, 2,
                       NULL, /* TODO : chain irq to IRL */
                       115200, chr, DEVICE_NATIVE_ENDIAN);
    }

    /* create qemu graphic console */
    s->ds = graphic_console_init(sm501_update_display, NULL,
                                 NULL, NULL, s);
}