hw/tusb6010.c

   1 /*
   2  * Texas Instruments TUSB6010 emulation.
   3  * Based on reverse-engineering of a linux driver.
   4  *
   5  * Copyright (C) 2008 Nokia Corporation
   6  * Written by Andrzej Zaborowski <andrew@openedhand.com>
   7  *
   8  * This program is free software; you can redistribute it and/or
   9  * modify it under the terms of the GNU General Public License as
  10  * published by the Free Software Foundation; either version 2 or
  11  * (at your option) version 3 of the License.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License along
  19  * with this program; if not, see <http://www.gnu.org/licenses/>.
  20  */
  21 #include "qemu-common.h"
  22 #include "qemu-timer.h"
  23 #include "usb.h"
  24 #include "omap.h"
  25 #include "irq.h"
  26 #include "devices.h"
  27
  28 struct TUSBState {
  29     int iomemtype[2];
  30     qemu_irq irq;
  31     MUSBState *musb;
  32     QEMUTimer *otg_timer;
  33     QEMUTimer *pwr_timer;
  34
  35     int power;
  36     uint32_t scratch;
  37     uint16_t test_reset;
  38     uint32_t prcm_config;
  39     uint32_t prcm_mngmt;
  40     uint16_t otg_status;
  41     uint32_t dev_config;
  42     int host_mode;
  43     uint32_t intr;
  44     uint32_t intr_ok;
  45     uint32_t mask;
  46     uint32_t usbip_intr;
  47     uint32_t usbip_mask;
  48     uint32_t gpio_intr;
  49     uint32_t gpio_mask;
  50     uint32_t gpio_config;
  51     uint32_t dma_intr;
  52     uint32_t dma_mask;
  53     uint32_t dma_map;
  54     uint32_t dma_config;
  55     uint32_t ep0_config;
  56     uint32_t rx_config[15];
  57     uint32_t tx_config[15];
  58     uint32_t wkup_mask;
  59     uint32_t pullup[2];
  60     uint32_t control_config;
  61     uint32_t otg_timer_val;
  62 };
  63
  64 #define TUSB_DEVCLOCK                   60000000        /* 60 MHz */
  65
  66 #define TUSB_VLYNQ_CTRL                 0x004
  67
  68 /* Mentor Graphics OTG core registers.  */
  69 #define TUSB_BASE_OFFSET                0x400
  70
  71 /* FIFO registers, 32-bit.  */
  72 #define TUSB_FIFO_BASE                  0x600
  73
  74 /* Device System & Control registers, 32-bit.  */
  75 #define TUSB_SYS_REG_BASE               0x800
  76
  77 #define TUSB_DEV_CONF                   (TUSB_SYS_REG_BASE + 0x000)
  78 #define TUSB_DEV_CONF_USB_HOST_MODE     (1 << 16)
  79 #define TUSB_DEV_CONF_PROD_TEST_MODE    (1 << 15)
  80 #define TUSB_DEV_CONF_SOFT_ID           (1 << 1)
  81 #define TUSB_DEV_CONF_ID_SEL            (1 << 0)
  82
  83 #define TUSB_PHY_OTG_CTRL_ENABLE        (TUSB_SYS_REG_BASE + 0x004)
  84 #define TUSB_PHY_OTG_CTRL               (TUSB_SYS_REG_BASE + 0x008)
  85 #define TUSB_PHY_OTG_CTRL_WRPROTECT     (0xa5 << 24)
  86 #define TUSB_PHY_OTG_CTRL_O_ID_PULLUP   (1 << 23)
  87 #define TUSB_PHY_OTG_CTRL_O_VBUS_DET_EN (1 << 19)
  88 #define TUSB_PHY_OTG_CTRL_O_SESS_END_EN (1 << 18)
  89 #define TUSB_PHY_OTG_CTRL_TESTM2        (1 << 17)
  90 #define TUSB_PHY_OTG_CTRL_TESTM1        (1 << 16)
  91 #define TUSB_PHY_OTG_CTRL_TESTM0        (1 << 15)
  92 #define TUSB_PHY_OTG_CTRL_TX_DATA2      (1 << 14)
  93 #define TUSB_PHY_OTG_CTRL_TX_GZ2        (1 << 13)
  94 #define TUSB_PHY_OTG_CTRL_TX_ENABLE2    (1 << 12)
  95 #define TUSB_PHY_OTG_CTRL_DM_PULLDOWN   (1 << 11)
  96 #define TUSB_PHY_OTG_CTRL_DP_PULLDOWN   (1 << 10)
  97 #define TUSB_PHY_OTG_CTRL_OSC_EN        (1 << 9)
  98 #define TUSB_PHY_OTG_CTRL_PHYREF_CLK(v) (((v) & 3) << 7)
  99 #define TUSB_PHY_OTG_CTRL_PD            (1 << 6)
 100 #define TUSB_PHY_OTG_CTRL_PLL_ON        (1 << 5)
 101 #define TUSB_PHY_OTG_CTRL_EXT_RPU       (1 << 4)
 102 #define TUSB_PHY_OTG_CTRL_PWR_GOOD      (1 << 3)
 103 #define TUSB_PHY_OTG_CTRL_RESET         (1 << 2)
 104 #define TUSB_PHY_OTG_CTRL_SUSPENDM      (1 << 1)
 105 #define TUSB_PHY_OTG_CTRL_CLK_MODE      (1 << 0)
 106
 107 /* OTG status register */
 108 #define TUSB_DEV_OTG_STAT               (TUSB_SYS_REG_BASE + 0x00c)
 109 #define TUSB_DEV_OTG_STAT_PWR_CLK_GOOD  (1 << 8)
 110 #define TUSB_DEV_OTG_STAT_SESS_END      (1 << 7)
 111 #define TUSB_DEV_OTG_STAT_SESS_VALID    (1 << 6)
 112 #define TUSB_DEV_OTG_STAT_VBUS_VALID    (1 << 5)
 113 #define TUSB_DEV_OTG_STAT_VBUS_SENSE    (1 << 4)
 114 #define TUSB_DEV_OTG_STAT_ID_STATUS     (1 << 3)
 115 #define TUSB_DEV_OTG_STAT_HOST_DISCON   (1 << 2)
 116 #define TUSB_DEV_OTG_STAT_LINE_STATE    (3 << 0)
 117 #define TUSB_DEV_OTG_STAT_DP_ENABLE     (1 << 1)
 118 #define TUSB_DEV_OTG_STAT_DM_ENABLE     (1 << 0)
 119
 120 #define TUSB_DEV_OTG_TIMER              (TUSB_SYS_REG_BASE + 0x010)
 121 #define TUSB_DEV_OTG_TIMER_ENABLE       (1 << 31)
 122 #define TUSB_DEV_OTG_TIMER_VAL(v)       ((v) & 0x07ffffff)
 123 #define TUSB_PRCM_REV                   (TUSB_SYS_REG_BASE + 0x014)
 124
 125 /* PRCM configuration register */
 126 #define TUSB_PRCM_CONF                  (TUSB_SYS_REG_BASE + 0x018)
 127 #define TUSB_PRCM_CONF_SFW_CPEN         (1 << 24)
 128 #define TUSB_PRCM_CONF_SYS_CLKSEL(v)    (((v) & 3) << 16)
 129
 130 /* PRCM management register */
 131 #define TUSB_PRCM_MNGMT                 (TUSB_SYS_REG_BASE + 0x01c)
 132 #define TUSB_PRCM_MNGMT_SRP_FIX_TMR(v)  (((v) & 0xf) << 25)
 133 #define TUSB_PRCM_MNGMT_SRP_FIX_EN      (1 << 24)
 134 #define TUSB_PRCM_MNGMT_VBUS_VAL_TMR(v) (((v) & 0xf) << 20)
 135 #define TUSB_PRCM_MNGMT_VBUS_VAL_FLT_EN (1 << 19)
 136 #define TUSB_PRCM_MNGMT_DFT_CLK_DIS     (1 << 18)
 137 #define TUSB_PRCM_MNGMT_VLYNQ_CLK_DIS   (1 << 17)
 138 #define TUSB_PRCM_MNGMT_OTG_SESS_END_EN (1 << 10)
 139 #define TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN (1 << 9)
 140 #define TUSB_PRCM_MNGMT_OTG_ID_PULLUP   (1 << 8)
 141 #define TUSB_PRCM_MNGMT_15_SW_EN        (1 << 4)
 142 #define TUSB_PRCM_MNGMT_33_SW_EN        (1 << 3)
 143 #define TUSB_PRCM_MNGMT_5V_CPEN         (1 << 2)
 144 #define TUSB_PRCM_MNGMT_PM_IDLE         (1 << 1)
 145 #define TUSB_PRCM_MNGMT_DEV_IDLE        (1 << 0)
 146
 147 /* Wake-up source clear and mask registers */
 148 #define TUSB_PRCM_WAKEUP_SOURCE         (TUSB_SYS_REG_BASE + 0x020)
 149 #define TUSB_PRCM_WAKEUP_CLEAR          (TUSB_SYS_REG_BASE + 0x028)
 150 #define TUSB_PRCM_WAKEUP_MASK           (TUSB_SYS_REG_BASE + 0x02c)
 151 #define TUSB_PRCM_WAKEUP_RESERVED_BITS  (0xffffe << 13)
 152 #define TUSB_PRCM_WGPIO_7               (1 << 12)
 153 #define TUSB_PRCM_WGPIO_6               (1 << 11)
 154 #define TUSB_PRCM_WGPIO_5               (1 << 10)
 155 #define TUSB_PRCM_WGPIO_4               (1 << 9)
 156 #define TUSB_PRCM_WGPIO_3               (1 << 8)
 157 #define TUSB_PRCM_WGPIO_2               (1 << 7)
 158 #define TUSB_PRCM_WGPIO_1               (1 << 6)
 159 #define TUSB_PRCM_WGPIO_0               (1 << 5)
 160 #define TUSB_PRCM_WHOSTDISCON           (1 << 4)        /* Host disconnect */
 161 #define TUSB_PRCM_WBUS                  (1 << 3)        /* USB bus resume */
 162 #define TUSB_PRCM_WNORCS                (1 << 2)        /* NOR chip select */
 163 #define TUSB_PRCM_WVBUS                 (1 << 1)        /* OTG PHY VBUS */
 164 #define TUSB_PRCM_WID                   (1 << 0)        /* OTG PHY ID detect */
 165
 166 #define TUSB_PULLUP_1_CTRL              (TUSB_SYS_REG_BASE + 0x030)
 167 #define TUSB_PULLUP_2_CTRL              (TUSB_SYS_REG_BASE + 0x034)
 168 #define TUSB_INT_CTRL_REV               (TUSB_SYS_REG_BASE + 0x038)
 169 #define TUSB_INT_CTRL_CONF              (TUSB_SYS_REG_BASE + 0x03c)
 170 #define TUSB_USBIP_INT_SRC              (TUSB_SYS_REG_BASE + 0x040)
 171 #define TUSB_USBIP_INT_SET              (TUSB_SYS_REG_BASE + 0x044)
 172 #define TUSB_USBIP_INT_CLEAR            (TUSB_SYS_REG_BASE + 0x048)
 173 #define TUSB_USBIP_INT_MASK             (TUSB_SYS_REG_BASE + 0x04c)
 174 #define TUSB_DMA_INT_SRC                (TUSB_SYS_REG_BASE + 0x050)
 175 #define TUSB_DMA_INT_SET                (TUSB_SYS_REG_BASE + 0x054)
 176 #define TUSB_DMA_INT_CLEAR              (TUSB_SYS_REG_BASE + 0x058)
 177 #define TUSB_DMA_INT_MASK               (TUSB_SYS_REG_BASE + 0x05c)
 178 #define TUSB_GPIO_INT_SRC               (TUSB_SYS_REG_BASE + 0x060)
 179 #define TUSB_GPIO_INT_SET               (TUSB_SYS_REG_BASE + 0x064)
 180 #define TUSB_GPIO_INT_CLEAR             (TUSB_SYS_REG_BASE + 0x068)
 181 #define TUSB_GPIO_INT_MASK              (TUSB_SYS_REG_BASE + 0x06c)
 182
 183 /* NOR flash interrupt source registers */
 184 #define TUSB_INT_SRC                    (TUSB_SYS_REG_BASE + 0x070)
 185 #define TUSB_INT_SRC_SET                (TUSB_SYS_REG_BASE + 0x074)
 186 #define TUSB_INT_SRC_CLEAR              (TUSB_SYS_REG_BASE + 0x078)
 187 #define TUSB_INT_MASK                   (TUSB_SYS_REG_BASE + 0x07c)
 188 #define TUSB_INT_SRC_TXRX_DMA_DONE      (1 << 24)
 189 #define TUSB_INT_SRC_USB_IP_CORE        (1 << 17)
 190 #define TUSB_INT_SRC_OTG_TIMEOUT        (1 << 16)
 191 #define TUSB_INT_SRC_VBUS_SENSE_CHNG    (1 << 15)
 192 #define TUSB_INT_SRC_ID_STATUS_CHNG     (1 << 14)
 193 #define TUSB_INT_SRC_DEV_WAKEUP         (1 << 13)
 194 #define TUSB_INT_SRC_DEV_READY          (1 << 12)
 195 #define TUSB_INT_SRC_USB_IP_TX          (1 << 9)
 196 #define TUSB_INT_SRC_USB_IP_RX          (1 << 8)
 197 #define TUSB_INT_SRC_USB_IP_VBUS_ERR    (1 << 7)
 198 #define TUSB_INT_SRC_USB_IP_VBUS_REQ    (1 << 6)
 199 #define TUSB_INT_SRC_USB_IP_DISCON      (1 << 5)
 200 #define TUSB_INT_SRC_USB_IP_CONN        (1 << 4)
 201 #define TUSB_INT_SRC_USB_IP_SOF         (1 << 3)
 202 #define TUSB_INT_SRC_USB_IP_RST_BABBLE  (1 << 2)
 203 #define TUSB_INT_SRC_USB_IP_RESUME      (1 << 1)
 204 #define TUSB_INT_SRC_USB_IP_SUSPEND     (1 << 0)
 205
 206 #define TUSB_GPIO_REV                   (TUSB_SYS_REG_BASE + 0x080)
 207 #define TUSB_GPIO_CONF                  (TUSB_SYS_REG_BASE + 0x084)
 208 #define TUSB_DMA_CTRL_REV               (TUSB_SYS_REG_BASE + 0x100)
 209 #define TUSB_DMA_REQ_CONF               (TUSB_SYS_REG_BASE + 0x104)
 210 #define TUSB_EP0_CONF                   (TUSB_SYS_REG_BASE + 0x108)
 211 #define TUSB_EP_IN_SIZE                 (TUSB_SYS_REG_BASE + 0x10c)
 212 #define TUSB_DMA_EP_MAP                 (TUSB_SYS_REG_BASE + 0x148)
 213 #define TUSB_EP_OUT_SIZE                (TUSB_SYS_REG_BASE + 0x14c)
 214 #define TUSB_EP_MAX_PACKET_SIZE_OFFSET  (TUSB_SYS_REG_BASE + 0x188)
 215 #define TUSB_SCRATCH_PAD                (TUSB_SYS_REG_BASE + 0x1c4)
 216 #define TUSB_WAIT_COUNT                 (TUSB_SYS_REG_BASE + 0x1c8)
 217 #define TUSB_PROD_TEST_RESET            (TUSB_SYS_REG_BASE + 0x1d8)
 218
 219 #define TUSB_DIDR1_LO                   (TUSB_SYS_REG_BASE + 0x1f8)
 220 #define TUSB_DIDR1_HI                   (TUSB_SYS_REG_BASE + 0x1fc)
 221
 222 /* Device System & Control register bitfields */
 223 #define TUSB_INT_CTRL_CONF_INT_RLCYC(v) (((v) & 0x7) << 18)
 224 #define TUSB_INT_CTRL_CONF_INT_POLARITY (1 << 17)
 225 #define TUSB_INT_CTRL_CONF_INT_MODE     (1 << 16)
 226 #define TUSB_GPIO_CONF_DMAREQ(v)        (((v) & 0x3f) << 24)
 227 #define TUSB_DMA_REQ_CONF_BURST_SIZE(v) (((v) & 3) << 26)
 228 #define TUSB_DMA_REQ_CONF_DMA_RQ_EN(v)  (((v) & 0x3f) << 20)
 229 #define TUSB_DMA_REQ_CONF_DMA_RQ_ASR(v) (((v) & 0xf) << 16)
 230 #define TUSB_EP0_CONFIG_SW_EN           (1 << 8)
 231 #define TUSB_EP0_CONFIG_DIR_TX          (1 << 7)
 232 #define TUSB_EP0_CONFIG_XFR_SIZE(v)     ((v) & 0x7f)
 233 #define TUSB_EP_CONFIG_SW_EN            (1 << 31)
 234 #define TUSB_EP_CONFIG_XFR_SIZE(v)      ((v) & 0x7fffffff)
 235 #define TUSB_PROD_TEST_RESET_VAL        0xa596
 236
 237 int tusb6010_sync_io(TUSBState *s)
 238 {
 239     return s->iomemtype[0];
 240 }
 241
 242 int tusb6010_async_io(TUSBState *s)
 243 {
 244     return s->iomemtype[1];
 245 }
 246
 247 static void tusb_intr_update(TUSBState *s)
 248 {
 249     if (s->control_config & TUSB_INT_CTRL_CONF_INT_POLARITY)
 250         qemu_set_irq(s->irq, s->intr & ~s->mask & s->intr_ok);
 251     else
 252         qemu_set_irq(s->irq, (!(s->intr & ~s->mask)) & s->intr_ok);
 253 }
 254
 255 static void tusb_usbip_intr_update(TUSBState *s)
 256 {
 257     /* TX interrupt in the MUSB */
 258     if (s->usbip_intr & 0x0000ffff & ~s->usbip_mask)
 259         s->intr |= TUSB_INT_SRC_USB_IP_TX;
 260     else
 261         s->intr &= ~TUSB_INT_SRC_USB_IP_TX;
 262
 263     /* RX interrupt in the MUSB */
 264     if (s->usbip_intr & 0xffff0000 & ~s->usbip_mask)
 265         s->intr |= TUSB_INT_SRC_USB_IP_RX;
 266     else
 267         s->intr &= ~TUSB_INT_SRC_USB_IP_RX;
 268
 269     /* XXX: What about TUSB_INT_SRC_USB_IP_CORE?  */
 270
 271     tusb_intr_update(s);
 272 }
 273
 274 static void tusb_dma_intr_update(TUSBState *s)
 275 {
 276     if (s->dma_intr & ~s->dma_mask)
 277         s->intr |= TUSB_INT_SRC_TXRX_DMA_DONE;
 278     else
 279         s->intr &= ~TUSB_INT_SRC_TXRX_DMA_DONE;
 280
 281     tusb_intr_update(s);
 282 }
 283
 284 static void tusb_gpio_intr_update(TUSBState *s)
 285 {
 286     /* TODO: How is this signalled?  */
 287 }
 288
 289 extern CPUReadMemoryFunc * const musb_read[];
 290 extern CPUWriteMemoryFunc * const musb_write[];
 291
 292 static uint32_t tusb_async_readb(void *opaque, target_phys_addr_t addr)
 293 {
 294     TUSBState *s = (TUSBState *) opaque;
 295
 296     switch (addr & 0xfff) {
 297     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 298         return musb_read[0](s->musb, addr & 0x1ff);
 299
 300     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 301         return musb_read[0](s->musb, 0x20 + ((addr >> 3) & 0x3c));
 302     }
 303
 304     printf("%s: unknown register at %03x\n",
 305                     __FUNCTION__, (int) (addr & 0xfff));
 306     return 0;
 307 }
 308
 309 static uint32_t tusb_async_readh(void *opaque, target_phys_addr_t addr)
 310 {
 311     TUSBState *s = (TUSBState *) opaque;
 312
 313     switch (addr & 0xfff) {
 314     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 315         return musb_read[1](s->musb, addr & 0x1ff);
 316
 317     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 318         return musb_read[1](s->musb, 0x20 + ((addr >> 3) & 0x3c));
 319     }
 320
 321     printf("%s: unknown register at %03x\n",
 322                     __FUNCTION__, (int) (addr & 0xfff));
 323     return 0;
 324 }
 325
 326 static uint32_t tusb_async_readw(void *opaque, target_phys_addr_t addr)
 327 {
 328     TUSBState *s = (TUSBState *) opaque;
 329     int offset = addr & 0xfff;
 330     int epnum;
 331     uint32_t ret;
 332
 333     switch (offset) {
 334     case TUSB_DEV_CONF:
 335         return s->dev_config;
 336
 337     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 338         return musb_read[2](s->musb, offset & 0x1ff);
 339
 340     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 341         return musb_read[2](s->musb, 0x20 + ((addr >> 3) & 0x3c));
 342
 343     case TUSB_PHY_OTG_CTRL_ENABLE:
 344     case TUSB_PHY_OTG_CTRL:
 345         return 0x00;    /* TODO */
 346
 347     case TUSB_DEV_OTG_STAT:
 348         ret = s->otg_status;
 349 #if 0
 350         if (!(s->prcm_mngmt & TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN))
 351             ret &= ~TUSB_DEV_OTG_STAT_VBUS_VALID;
 352 #endif
 353         return ret;
 354     case TUSB_DEV_OTG_TIMER:
 355         return s->otg_timer_val;
 356
 357     case TUSB_PRCM_REV:
 358         return 0x20;
 359     case TUSB_PRCM_CONF:
 360         return s->prcm_config;
 361     case TUSB_PRCM_MNGMT:
 362         return s->prcm_mngmt;
 363     case TUSB_PRCM_WAKEUP_SOURCE:
 364     case TUSB_PRCM_WAKEUP_CLEAR:        /* TODO: What does this one return?  */
 365         return 0x00000000;
 366     case TUSB_PRCM_WAKEUP_MASK:
 367         return s->wkup_mask;
 368
 369     case TUSB_PULLUP_1_CTRL:
 370         return s->pullup[0];
 371     case TUSB_PULLUP_2_CTRL:
 372         return s->pullup[1];
 373
 374     case TUSB_INT_CTRL_REV:
 375         return 0x20;
 376     case TUSB_INT_CTRL_CONF:
 377         return s->control_config;
 378
 379     case TUSB_USBIP_INT_SRC:
 380     case TUSB_USBIP_INT_SET:    /* TODO: What do these two return?  */
 381     case TUSB_USBIP_INT_CLEAR:
 382         return s->usbip_intr;
 383     case TUSB_USBIP_INT_MASK:
 384         return s->usbip_mask;
 385
 386     case TUSB_DMA_INT_SRC:
 387     case TUSB_DMA_INT_SET:      /* TODO: What do these two return?  */
 388     case TUSB_DMA_INT_CLEAR:
 389         return s->dma_intr;
 390     case TUSB_DMA_INT_MASK:
 391         return s->dma_mask;
 392
 393     case TUSB_GPIO_INT_SRC:     /* TODO: What do these two return?  */
 394     case TUSB_GPIO_INT_SET:
 395     case TUSB_GPIO_INT_CLEAR:
 396         return s->gpio_intr;
 397     case TUSB_GPIO_INT_MASK:
 398         return s->gpio_mask;
 399
 400     case TUSB_INT_SRC:
 401     case TUSB_INT_SRC_SET:      /* TODO: What do these two return?  */
 402     case TUSB_INT_SRC_CLEAR:
 403         return s->intr;
 404     case TUSB_INT_MASK:
 405         return s->mask;
 406
 407     case TUSB_GPIO_REV:
 408         return 0x30;
 409     case TUSB_GPIO_CONF:
 410         return s->gpio_config;
 411
 412     case TUSB_DMA_CTRL_REV:
 413         return 0x30;
 414     case TUSB_DMA_REQ_CONF:
 415         return s->dma_config;
 416     case TUSB_EP0_CONF:
 417         return s->ep0_config;
 418     case TUSB_EP_IN_SIZE ... (TUSB_EP_IN_SIZE + 0x3b):
 419         epnum = (offset - TUSB_EP_IN_SIZE) >> 2;
 420         return s->tx_config[epnum];
 421     case TUSB_DMA_EP_MAP:
 422         return s->dma_map;
 423     case TUSB_EP_OUT_SIZE ... (TUSB_EP_OUT_SIZE + 0x3b):
 424         epnum = (offset - TUSB_EP_OUT_SIZE) >> 2;
 425         return s->rx_config[epnum];
 426     case TUSB_EP_MAX_PACKET_SIZE_OFFSET ...
 427             (TUSB_EP_MAX_PACKET_SIZE_OFFSET + 0x3b):
 428         epnum = (offset - TUSB_EP_MAX_PACKET_SIZE_OFFSET) >> 2;
 429         return 0x00000000;      /* TODO */
 430     case TUSB_WAIT_COUNT:
 431         return 0x00;            /* TODO */
 432
 433     case TUSB_SCRATCH_PAD:
 434         return s->scratch;
 435
 436     case TUSB_PROD_TEST_RESET:
 437         return s->test_reset;
 438
 439     /* DIE IDs */
 440     case TUSB_DIDR1_LO:
 441         return 0xa9453c59;
 442     case TUSB_DIDR1_HI:
 443         return 0x54059adf;
 444     }
 445
 446     printf("%s: unknown register at %03x\n", __FUNCTION__, offset);
 447     return 0;
 448 }
 449
 450 static void tusb_async_writeb(void *opaque, target_phys_addr_t addr,
 451                 uint32_t value)
 452 {
 453     TUSBState *s = (TUSBState *) opaque;
 454
 455     switch (addr & 0xfff) {
 456     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 457         musb_write[0](s->musb, addr & 0x1ff, value);
 458         break;
 459
 460     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 461         musb_write[0](s->musb, 0x20 + ((addr >> 3) & 0x3c), value);
 462         break;
 463
 464     default:
 465         printf("%s: unknown register at %03x\n",
 466                         __FUNCTION__, (int) (addr & 0xfff));
 467         return;
 468     }
 469 }
 470
 471 static void tusb_async_writeh(void *opaque, target_phys_addr_t addr,
 472                 uint32_t value)
 473 {
 474     TUSBState *s = (TUSBState *) opaque;
 475
 476     switch (addr & 0xfff) {
 477     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 478         musb_write[1](s->musb, addr & 0x1ff, value);
 479         break;
 480
 481     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 482         musb_write[1](s->musb, 0x20 + ((addr >> 3) & 0x3c), value);
 483         break;
 484
 485     default:
 486         printf("%s: unknown register at %03x\n",
 487                         __FUNCTION__, (int) (addr & 0xfff));
 488         return;
 489     }
 490 }
 491
 492 static void tusb_async_writew(void *opaque, target_phys_addr_t addr,
 493                 uint32_t value)
 494 {
 495     TUSBState *s = (TUSBState *) opaque;
 496     int offset = addr & 0xfff;
 497     int epnum;
 498
 499     switch (offset) {
 500     case TUSB_VLYNQ_CTRL:
 501         break;
 502
 503     case TUSB_BASE_OFFSET ... (TUSB_BASE_OFFSET | 0x1ff):
 504         musb_write[2](s->musb, offset & 0x1ff, value);
 505         break;
 506
 507     case TUSB_FIFO_BASE ... (TUSB_FIFO_BASE | 0x1ff):
 508         musb_write[2](s->musb, 0x20 + ((addr >> 3) & 0x3c), value);
 509         break;
 510
 511     case TUSB_DEV_CONF:
 512         s->dev_config = value;
 513         s->host_mode = (value & TUSB_DEV_CONF_USB_HOST_MODE);
 514         if (value & TUSB_DEV_CONF_PROD_TEST_MODE)
 515             hw_error("%s: Product Test mode not allowed\n", __FUNCTION__);
 516         break;
 517
 518     case TUSB_PHY_OTG_CTRL_ENABLE:
 519     case TUSB_PHY_OTG_CTRL:
 520         return;         /* TODO */
 521     case TUSB_DEV_OTG_TIMER:
 522         s->otg_timer_val = value;
 523         if (value & TUSB_DEV_OTG_TIMER_ENABLE)
 524             qemu_mod_timer(s->otg_timer, qemu_get_clock(vm_clock) +
 525                             muldiv64(TUSB_DEV_OTG_TIMER_VAL(value),
 526                                      get_ticks_per_sec(), TUSB_DEVCLOCK));
 527         else
 528             qemu_del_timer(s->otg_timer);
 529         break;
 530
 531     case TUSB_PRCM_CONF:
 532         s->prcm_config = value;
 533         break;
 534     case TUSB_PRCM_MNGMT:
 535         s->prcm_mngmt = value;
 536         break;
 537     case TUSB_PRCM_WAKEUP_CLEAR:
 538         break;
 539     case TUSB_PRCM_WAKEUP_MASK:
 540         s->wkup_mask = value;
 541         break;
 542
 543     case TUSB_PULLUP_1_CTRL:
 544         s->pullup[0] = value;
 545         break;
 546     case TUSB_PULLUP_2_CTRL:
 547         s->pullup[1] = value;
 548         break;
 549     case TUSB_INT_CTRL_CONF:
 550         s->control_config = value;
 551         tusb_intr_update(s);
 552         break;
 553
 554     case TUSB_USBIP_INT_SET:
 555         s->usbip_intr |= value;
 556         tusb_usbip_intr_update(s);
 557         break;
 558     case TUSB_USBIP_INT_CLEAR:
 559         s->usbip_intr &= ~value;
 560         tusb_usbip_intr_update(s);
 561         musb_core_intr_clear(s->musb, ~value);
 562         break;
 563     case TUSB_USBIP_INT_MASK:
 564         s->usbip_mask = value;
 565         tusb_usbip_intr_update(s);
 566         break;
 567
 568     case TUSB_DMA_INT_SET:
 569         s->dma_intr |= value;
 570         tusb_dma_intr_update(s);
 571         break;
 572     case TUSB_DMA_INT_CLEAR:
 573         s->dma_intr &= ~value;
 574         tusb_dma_intr_update(s);
 575         break;
 576     case TUSB_DMA_INT_MASK:
 577         s->dma_mask = value;
 578         tusb_dma_intr_update(s);
 579         break;
 580
 581     case TUSB_GPIO_INT_SET:
 582         s->gpio_intr |= value;
 583         tusb_gpio_intr_update(s);
 584         break;
 585     case TUSB_GPIO_INT_CLEAR:
 586         s->gpio_intr &= ~value;
 587         tusb_gpio_intr_update(s);
 588         break;
 589     case TUSB_GPIO_INT_MASK:
 590         s->gpio_mask = value;
 591         tusb_gpio_intr_update(s);
 592         break;
 593
 594     case TUSB_INT_SRC_SET:
 595         s->intr |= value;
 596         tusb_intr_update(s);
 597         break;
 598     case TUSB_INT_SRC_CLEAR:
 599         s->intr &= ~value;
 600         tusb_intr_update(s);
 601         break;
 602     case TUSB_INT_MASK:
 603         s->mask = value;
 604         tusb_intr_update(s);
 605         break;
 606
 607     case TUSB_GPIO_CONF:
 608         s->gpio_config = value;
 609         break;
 610     case TUSB_DMA_REQ_CONF:
 611         s->dma_config = value;
 612         break;
 613     case TUSB_EP0_CONF:
 614         s->ep0_config = value & 0x1ff;
 615         musb_set_size(s->musb, 0, TUSB_EP0_CONFIG_XFR_SIZE(value),
 616                         value & TUSB_EP0_CONFIG_DIR_TX);
 617         break;
 618     case TUSB_EP_IN_SIZE ... (TUSB_EP_IN_SIZE + 0x3b):
 619         epnum = (offset - TUSB_EP_IN_SIZE) >> 2;
 620         s->tx_config[epnum] = value;
 621         musb_set_size(s->musb, epnum + 1, TUSB_EP_CONFIG_XFR_SIZE(value), 1);
 622         break;
 623     case TUSB_DMA_EP_MAP:
 624         s->dma_map = value;
 625         break;
 626     case TUSB_EP_OUT_SIZE ... (TUSB_EP_OUT_SIZE + 0x3b):
 627         epnum = (offset - TUSB_EP_OUT_SIZE) >> 2;
 628         s->rx_config[epnum] = value;
 629         musb_set_size(s->musb, epnum + 1, TUSB_EP_CONFIG_XFR_SIZE(value), 0);
 630         break;
 631     case TUSB_EP_MAX_PACKET_SIZE_OFFSET ...
 632             (TUSB_EP_MAX_PACKET_SIZE_OFFSET + 0x3b):
 633         epnum = (offset - TUSB_EP_MAX_PACKET_SIZE_OFFSET) >> 2;
 634         return;         /* TODO */
 635     case TUSB_WAIT_COUNT:
 636         return;         /* TODO */
 637
 638     case TUSB_SCRATCH_PAD:
 639         s->scratch = value;
 640         break;
 641
 642     case TUSB_PROD_TEST_RESET:
 643         s->test_reset = value;
 644         break;
 645
 646     default:
 647         printf("%s: unknown register at %03x\n", __FUNCTION__, offset);
 648         return;
 649     }
 650 }
 651
 652 static CPUReadMemoryFunc * const tusb_async_readfn[] = {
 653     tusb_async_readb,
 654     tusb_async_readh,
 655     tusb_async_readw,
 656 };
 657
 658 static CPUWriteMemoryFunc * const tusb_async_writefn[] = {
 659     tusb_async_writeb,
 660     tusb_async_writeh,
 661     tusb_async_writew,
 662 };
 663
 664 static void tusb_otg_tick(void *opaque)
 665 {
 666     TUSBState *s = (TUSBState *) opaque;
 667
 668     s->otg_timer_val = 0;
 669     s->intr |= TUSB_INT_SRC_OTG_TIMEOUT;
 670     tusb_intr_update(s);
 671 }
 672
 673 static void tusb_power_tick(void *opaque)
 674 {
 675     TUSBState *s = (TUSBState *) opaque;
 676
 677     if (s->power) {
 678         s->intr_ok = ~0;
 679         tusb_intr_update(s);
 680     }
 681 }
 682
 683 static void tusb_musb_core_intr(void *opaque, int source, int level)
 684 {
 685     TUSBState *s = (TUSBState *) opaque;
 686     uint16_t otg_status = s->otg_status;
 687
 688     switch (source) {
 689     case musb_set_vbus:
 690         if (level)
 691             otg_status |= TUSB_DEV_OTG_STAT_VBUS_VALID;
 692         else
 693             otg_status &= ~TUSB_DEV_OTG_STAT_VBUS_VALID;
 694
 695         /* XXX: only if TUSB_PHY_OTG_CTRL_OTG_VBUS_DET_EN set?  */
 696         /* XXX: only if TUSB_PRCM_MNGMT_OTG_VBUS_DET_EN set?  */
 697         if (s->otg_status != otg_status) {
 698             s->otg_status = otg_status;
 699             s->intr |= TUSB_INT_SRC_VBUS_SENSE_CHNG;
 700             tusb_intr_update(s);
 701         }
 702         break;
 703
 704     case musb_set_session:
 705         /* XXX: only if TUSB_PHY_OTG_CTRL_OTG_SESS_END_EN set?  */
 706         /* XXX: only if TUSB_PRCM_MNGMT_OTG_SESS_END_EN set?  */
 707         if (level) {
 708             s->otg_status |= TUSB_DEV_OTG_STAT_SESS_VALID;
 709             s->otg_status &= ~TUSB_DEV_OTG_STAT_SESS_END;
 710         } else {
 711             s->otg_status &= ~TUSB_DEV_OTG_STAT_SESS_VALID;
 712             s->otg_status |= TUSB_DEV_OTG_STAT_SESS_END;
 713         }
 714
 715         /* XXX: some IRQ or anything?  */
 716         break;
 717
 718     case musb_irq_tx:
 719     case musb_irq_rx:
 720         s->usbip_intr = musb_core_intr_get(s->musb);
 721         /* Fall through.  */
 722     default:
 723         if (level)
 724             s->intr |= 1 << source;
 725         else
 726             s->intr &= ~(1 << source);
 727         tusb_intr_update(s);
 728         break;
 729     }
 730 }
 731
 732 TUSBState *tusb6010_init(qemu_irq intr)
 733 {
 734     TUSBState *s = qemu_mallocz(sizeof(*s));
 735
 736     s->test_reset = TUSB_PROD_TEST_RESET_VAL;
 737     s->host_mode = 0;
 738     s->dev_config = 0;
 739     s->otg_status = 0;  /* !TUSB_DEV_OTG_STAT_ID_STATUS means host mode */
 740     s->power = 0;
 741     s->mask = 0xffffffff;
 742     s->intr = 0x00000000;
 743     s->otg_timer_val = 0;
 744     s->iomemtype[1] = cpu_register_io_memory(tusb_async_readfn,
 745                     tusb_async_writefn, s);
 746     s->irq = intr;
 747     s->otg_timer = qemu_new_timer(vm_clock, tusb_otg_tick, s);
 748     s->pwr_timer = qemu_new_timer(vm_clock, tusb_power_tick, s);
 749     s->musb = musb_init(qemu_allocate_irqs(tusb_musb_core_intr, s,
 750                             __musb_irq_max));
 751
 752     return s;
 753 }
 754
 755 void tusb6010_power(TUSBState *s, int on)
 756 {
 757     if (!on)
 758         s->power = 0;
 759     else if (!s->power && on) {
 760         s->power = 1;
 761
 762         /* Pull the interrupt down after TUSB6010 comes up.  */
 763         s->intr_ok = 0;
 764         tusb_intr_update(s);
 765         qemu_mod_timer(s->pwr_timer,
 766                        qemu_get_clock(vm_clock) + get_ticks_per_sec() / 2);
 767     }
 768 }