hw/pci/shpc.c

   1 #include "qemu-common.h"
   2 #include <strings.h>
   3 #include <stdint.h>
   4 #include "qemu/range.h"
   5 #include "qemu/error-report.h"
   6 #include "hw/pci/shpc.h"
   7 #include "hw/pci/pci.h"
   8 #include "hw/pci/pci_bus.h"
   9 #include "hw/pci/msi.h"
  10
  11 /* TODO: model power only and disabled slot states. */
  12 /* TODO: handle SERR and wakeups */
  13 /* TODO: consider enabling 66MHz support */
  14
  15 /* TODO: remove fully only on state DISABLED and LED off.
  16  * track state to properly record this. */
  17
  18 /* SHPC Working Register Set */
  19 #define SHPC_BASE_OFFSET  0x00 /* 4 bytes */
  20 #define SHPC_SLOTS_33     0x04 /* 4 bytes. Also encodes PCI-X slots. */
  21 #define SHPC_SLOTS_66     0x08 /* 4 bytes. */
  22 #define SHPC_NSLOTS       0x0C /* 1 byte */
  23 #define SHPC_FIRST_DEV    0x0D /* 1 byte */
  24 #define SHPC_PHYS_SLOT    0x0E /* 2 byte */
  25 #define SHPC_PHYS_NUM_MAX 0x7ff
  26 #define SHPC_PHYS_NUM_UP  0x2000
  27 #define SHPC_PHYS_MRL     0x4000
  28 #define SHPC_PHYS_BUTTON  0x8000
  29 #define SHPC_SEC_BUS      0x10 /* 2 bytes */
  30 #define SHPC_SEC_BUS_33   0x0
  31 #define SHPC_SEC_BUS_66   0x1 /* Unused */
  32 #define SHPC_SEC_BUS_MASK 0x7
  33 #define SHPC_MSI_CTL      0x12 /* 1 byte */
  34 #define SHPC_PROG_IFC     0x13 /* 1 byte */
  35 #define SHPC_PROG_IFC_1_0 0x1
  36 #define SHPC_CMD_CODE     0x14 /* 1 byte */
  37 #define SHPC_CMD_TRGT     0x15 /* 1 byte */
  38 #define SHPC_CMD_TRGT_MIN 0x1
  39 #define SHPC_CMD_TRGT_MAX 0x1f
  40 #define SHPC_CMD_STATUS   0x16 /* 2 bytes */
  41 #define SHPC_CMD_STATUS_BUSY          0x1
  42 #define SHPC_CMD_STATUS_MRL_OPEN      0x2
  43 #define SHPC_CMD_STATUS_INVALID_CMD   0x4
  44 #define SHPC_CMD_STATUS_INVALID_MODE  0x8
  45 #define SHPC_INT_LOCATOR  0x18 /* 4 bytes */
  46 #define SHPC_INT_COMMAND  0x1
  47 #define SHPC_SERR_LOCATOR 0x1C /* 4 bytes */
  48 #define SHPC_SERR_INT     0x20 /* 4 bytes */
  49 #define SHPC_INT_DIS      0x1
  50 #define SHPC_SERR_DIS     0x2
  51 #define SHPC_CMD_INT_DIS  0x4
  52 #define SHPC_ARB_SERR_DIS 0x8
  53 #define SHPC_CMD_DETECTED 0x10000
  54 #define SHPC_ARB_DETECTED 0x20000
  55  /* 4 bytes * slot # (start from 0) */
  56 #define SHPC_SLOT_REG(s)         (0x24 + (s) * 4)
  57  /* 2 bytes */
  58 #define SHPC_SLOT_STATUS(s)       (0x0 + SHPC_SLOT_REG(s))
  59
  60 /* Same slot state masks are used for command and status registers */
  61 #define SHPC_SLOT_STATE_MASK     0x03
  62 #define SHPC_SLOT_STATE_SHIFT \
  63     (ffs(SHPC_SLOT_STATE_MASK) - 1)
  64
  65 #define SHPC_STATE_NO       0x0
  66 #define SHPC_STATE_PWRONLY  0x1
  67 #define SHPC_STATE_ENABLED  0x2
  68 #define SHPC_STATE_DISABLED 0x3
  69
  70 #define SHPC_SLOT_PWR_LED_MASK   0xC
  71 #define SHPC_SLOT_PWR_LED_SHIFT \
  72     (ffs(SHPC_SLOT_PWR_LED_MASK) - 1)
  73 #define SHPC_SLOT_ATTN_LED_MASK  0x30
  74 #define SHPC_SLOT_ATTN_LED_SHIFT \
  75     (ffs(SHPC_SLOT_ATTN_LED_MASK) - 1)
  76
  77 #define SHPC_LED_NO     0x0
  78 #define SHPC_LED_ON     0x1
  79 #define SHPC_LED_BLINK  0x2
  80 #define SHPC_LED_OFF    0x3
  81
  82 #define SHPC_SLOT_STATUS_PWR_FAULT      0x40
  83 #define SHPC_SLOT_STATUS_BUTTON         0x80
  84 #define SHPC_SLOT_STATUS_MRL_OPEN       0x100
  85 #define SHPC_SLOT_STATUS_66             0x200
  86 #define SHPC_SLOT_STATUS_PRSNT_MASK     0xC00
  87 #define SHPC_SLOT_STATUS_PRSNT_EMPTY    0x3
  88 #define SHPC_SLOT_STATUS_PRSNT_25W      0x1
  89 #define SHPC_SLOT_STATUS_PRSNT_15W      0x2
  90 #define SHPC_SLOT_STATUS_PRSNT_7_5W     0x0
  91
  92 #define SHPC_SLOT_STATUS_PRSNT_PCIX     0x3000
  93
  94
  95  /* 1 byte */
  96 #define SHPC_SLOT_EVENT_LATCH(s)        (0x2 + SHPC_SLOT_REG(s))
  97  /* 1 byte */
  98 #define SHPC_SLOT_EVENT_SERR_INT_DIS(d, s) (0x3 + SHPC_SLOT_REG(s))
  99 #define SHPC_SLOT_EVENT_PRESENCE        0x01
 100 #define SHPC_SLOT_EVENT_ISOLATED_FAULT  0x02
 101 #define SHPC_SLOT_EVENT_BUTTON          0x04
 102 #define SHPC_SLOT_EVENT_MRL             0x08
 103 #define SHPC_SLOT_EVENT_CONNECTED_FAULT 0x10
 104 /* Bits below are used for Serr/Int disable only */
 105 #define SHPC_SLOT_EVENT_MRL_SERR_DIS    0x20
 106 #define SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS 0x40
 107
 108 #define SHPC_MIN_SLOTS        1
 109 #define SHPC_MAX_SLOTS        31
 110 #define SHPC_SIZEOF(d)    SHPC_SLOT_REG((d)->shpc->nslots)
 111
 112 /* SHPC Slot identifiers */
 113
 114 /* Hotplug supported at 31 slots out of the total 32.  We reserve slot 0,
 115    and give the rest of them physical *and* pci numbers starting from 1, so
 116    they match logical numbers.  Note: this means that multiple slots must have
 117    different chassis number values, to make chassis+physical slot unique.
 118    TODO: make this configurable? */
 119 #define SHPC_IDX_TO_LOGICAL(slot) ((slot) + 1)
 120 #define SHPC_LOGICAL_TO_IDX(target) ((target) - 1)
 121 #define SHPC_IDX_TO_PCI(slot) ((slot) + 1)
 122 #define SHPC_PCI_TO_IDX(pci_slot) ((pci_slot) - 1)
 123 #define SHPC_IDX_TO_PHYSICAL(slot) ((slot) + 1)
 124
 125 static int roundup_pow_of_two(int x)
 126 {
 127     x |= (x >> 1);
 128     x |= (x >> 2);
 129     x |= (x >> 4);
 130     x |= (x >> 8);
 131     x |= (x >> 16);
 132     return x + 1;
 133 }
 134
 135 static uint16_t shpc_get_status(SHPCDevice *shpc, int slot, uint16_t msk)
 136 {
 137     uint8_t *status = shpc->config + SHPC_SLOT_STATUS(slot);
 138     return (pci_get_word(status) & msk) >> (ffs(msk) - 1);
 139 }
 140
 141 static void shpc_set_status(SHPCDevice *shpc,
 142                             int slot, uint8_t value, uint16_t msk)
 143 {
 144     uint8_t *status = shpc->config + SHPC_SLOT_STATUS(slot);
 145     pci_word_test_and_clear_mask(status, msk);
 146     pci_word_test_and_set_mask(status, value << (ffs(msk) - 1));
 147 }
 148
 149 static void shpc_interrupt_update(PCIDevice *d)
 150 {
 151     SHPCDevice *shpc = d->shpc;
 152     int slot;
 153     int level = 0;
 154     uint32_t serr_int;
 155     uint32_t int_locator = 0;
 156
 157     /* Update interrupt locator register */
 158     for (slot = 0; slot < shpc->nslots; ++slot) {
 159         uint8_t event = shpc->config[SHPC_SLOT_EVENT_LATCH(slot)];
 160         uint8_t disable = shpc->config[SHPC_SLOT_EVENT_SERR_INT_DIS(d, slot)];
 161         uint32_t mask = 1 << SHPC_IDX_TO_LOGICAL(slot);
 162         if (event & ~disable) {
 163             int_locator |= mask;
 164         }
 165     }
 166     serr_int = pci_get_long(shpc->config + SHPC_SERR_INT);
 167     if ((serr_int & SHPC_CMD_DETECTED) && !(serr_int & SHPC_CMD_INT_DIS)) {
 168         int_locator |= SHPC_INT_COMMAND;
 169     }
 170     pci_set_long(shpc->config + SHPC_INT_LOCATOR, int_locator);
 171     level = (!(serr_int & SHPC_INT_DIS) && int_locator) ? 1 : 0;
 172     if (msi_enabled(d) && shpc->msi_requested != level)
 173         msi_notify(d, 0);
 174     else
 175         pci_set_irq(d, level);
 176     shpc->msi_requested = level;
 177 }
 178
 179 static void shpc_set_sec_bus_speed(SHPCDevice *shpc, uint8_t speed)
 180 {
 181     switch (speed) {
 182     case SHPC_SEC_BUS_33:
 183         shpc->config[SHPC_SEC_BUS] &= ~SHPC_SEC_BUS_MASK;
 184         shpc->config[SHPC_SEC_BUS] |= speed;
 185         break;
 186     default:
 187         pci_word_test_and_set_mask(shpc->config + SHPC_CMD_STATUS,
 188                                    SHPC_CMD_STATUS_INVALID_MODE);
 189     }
 190 }
 191
 192 void shpc_reset(PCIDevice *d)
 193 {
 194     SHPCDevice *shpc = d->shpc;
 195     int nslots = shpc->nslots;
 196     int i;
 197     memset(shpc->config, 0, SHPC_SIZEOF(d));
 198     pci_set_byte(shpc->config + SHPC_NSLOTS, nslots);
 199     pci_set_long(shpc->config + SHPC_SLOTS_33, nslots);
 200     pci_set_long(shpc->config + SHPC_SLOTS_66, 0);
 201     pci_set_byte(shpc->config + SHPC_FIRST_DEV, SHPC_IDX_TO_PCI(0));
 202     pci_set_word(shpc->config + SHPC_PHYS_SLOT,
 203                  SHPC_IDX_TO_PHYSICAL(0) |
 204                  SHPC_PHYS_NUM_UP |
 205                  SHPC_PHYS_MRL |
 206                  SHPC_PHYS_BUTTON);
 207     pci_set_long(shpc->config + SHPC_SERR_INT, SHPC_INT_DIS |
 208                  SHPC_SERR_DIS |
 209                  SHPC_CMD_INT_DIS |
 210                  SHPC_ARB_SERR_DIS);
 211     pci_set_byte(shpc->config + SHPC_PROG_IFC, SHPC_PROG_IFC_1_0);
 212     pci_set_word(shpc->config + SHPC_SEC_BUS, SHPC_SEC_BUS_33);
 213     for (i = 0; i < shpc->nslots; ++i) {
 214         pci_set_byte(shpc->config + SHPC_SLOT_EVENT_SERR_INT_DIS(d, i),
 215                      SHPC_SLOT_EVENT_PRESENCE |
 216                      SHPC_SLOT_EVENT_ISOLATED_FAULT |
 217                      SHPC_SLOT_EVENT_BUTTON |
 218                      SHPC_SLOT_EVENT_MRL |
 219                      SHPC_SLOT_EVENT_CONNECTED_FAULT |
 220                      SHPC_SLOT_EVENT_MRL_SERR_DIS |
 221                      SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS);
 222         if (shpc->sec_bus->devices[PCI_DEVFN(SHPC_IDX_TO_PCI(i), 0)]) {
 223             shpc_set_status(shpc, i, SHPC_STATE_ENABLED, SHPC_SLOT_STATE_MASK);
 224             shpc_set_status(shpc, i, 0, SHPC_SLOT_STATUS_MRL_OPEN);
 225             shpc_set_status(shpc, i, SHPC_SLOT_STATUS_PRSNT_7_5W,
 226                             SHPC_SLOT_STATUS_PRSNT_MASK);
 227             shpc_set_status(shpc, i, SHPC_LED_ON, SHPC_SLOT_PWR_LED_MASK);
 228         } else {
 229             shpc_set_status(shpc, i, SHPC_STATE_DISABLED, SHPC_SLOT_STATE_MASK);
 230             shpc_set_status(shpc, i, 1, SHPC_SLOT_STATUS_MRL_OPEN);
 231             shpc_set_status(shpc, i, SHPC_SLOT_STATUS_PRSNT_EMPTY,
 232                             SHPC_SLOT_STATUS_PRSNT_MASK);
 233             shpc_set_status(shpc, i, SHPC_LED_OFF, SHPC_SLOT_PWR_LED_MASK);
 234         }
 235         shpc_set_status(shpc, i, 0, SHPC_SLOT_STATUS_66);
 236     }
 237     shpc_set_sec_bus_speed(shpc, SHPC_SEC_BUS_33);
 238     shpc->msi_requested = 0;
 239     shpc_interrupt_update(d);
 240 }
 241
 242 static void shpc_invalid_command(SHPCDevice *shpc)
 243 {
 244     pci_word_test_and_set_mask(shpc->config + SHPC_CMD_STATUS,
 245                                SHPC_CMD_STATUS_INVALID_CMD);
 246 }
 247
 248 static void shpc_free_devices_in_slot(SHPCDevice *shpc, int slot)
 249 {
 250     int devfn;
 251     int pci_slot = SHPC_IDX_TO_PCI(slot);
 252     for (devfn = PCI_DEVFN(pci_slot, 0);
 253          devfn <= PCI_DEVFN(pci_slot, PCI_FUNC_MAX - 1);
 254          ++devfn) {
 255         PCIDevice *affected_dev = shpc->sec_bus->devices[devfn];
 256         if (affected_dev) {
 257             object_unparent(OBJECT(affected_dev));
 258         }
 259     }
 260 }
 261
 262 static void shpc_slot_command(SHPCDevice *shpc, uint8_t target,
 263                               uint8_t state, uint8_t power, uint8_t attn)
 264 {
 265     uint8_t current_state;
 266     int slot = SHPC_LOGICAL_TO_IDX(target);
 267     if (target < SHPC_CMD_TRGT_MIN || slot >= shpc->nslots) {
 268         shpc_invalid_command(shpc);
 269         return;
 270     }
 271     current_state = shpc_get_status(shpc, slot, SHPC_SLOT_STATE_MASK);
 272     if (current_state == SHPC_STATE_ENABLED && state == SHPC_STATE_PWRONLY) {
 273         shpc_invalid_command(shpc);
 274         return;
 275     }
 276
 277     switch (power) {
 278     case SHPC_LED_NO:
 279         break;
 280     default:
 281         /* TODO: send event to monitor */
 282         shpc_set_status(shpc, slot, power, SHPC_SLOT_PWR_LED_MASK);
 283     }
 284     switch (attn) {
 285     case SHPC_LED_NO:
 286         break;
 287     default:
 288         /* TODO: send event to monitor */
 289         shpc_set_status(shpc, slot, attn, SHPC_SLOT_ATTN_LED_MASK);
 290     }
 291
 292     if ((current_state == SHPC_STATE_DISABLED && state == SHPC_STATE_PWRONLY) ||
 293         (current_state == SHPC_STATE_DISABLED && state == SHPC_STATE_ENABLED)) {
 294         shpc_set_status(shpc, slot, state, SHPC_SLOT_STATE_MASK);
 295     } else if ((current_state == SHPC_STATE_ENABLED ||
 296                 current_state == SHPC_STATE_PWRONLY) &&
 297                state == SHPC_STATE_DISABLED) {
 298         shpc_set_status(shpc, slot, state, SHPC_SLOT_STATE_MASK);
 299         power = shpc_get_status(shpc, slot, SHPC_SLOT_PWR_LED_MASK);
 300         /* TODO: track what monitor requested. */
 301         /* Look at LED to figure out whether it's ok to remove the device. */
 302         if (power == SHPC_LED_OFF) {
 303             shpc_free_devices_in_slot(shpc, slot);
 304             shpc_set_status(shpc, slot, 1, SHPC_SLOT_STATUS_MRL_OPEN);
 305             shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_EMPTY,
 306                             SHPC_SLOT_STATUS_PRSNT_MASK);
 307             shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
 308                 SHPC_SLOT_EVENT_BUTTON |
 309                 SHPC_SLOT_EVENT_MRL |
 310                 SHPC_SLOT_EVENT_PRESENCE;
 311         }
 312     }
 313 }
 314
 315 static void shpc_command(SHPCDevice *shpc)
 316 {
 317     uint8_t code = pci_get_byte(shpc->config + SHPC_CMD_CODE);
 318     uint8_t speed;
 319     uint8_t target;
 320     uint8_t attn;
 321     uint8_t power;
 322     uint8_t state;
 323     int i;
 324
 325     /* Clear status from the previous command. */
 326     pci_word_test_and_clear_mask(shpc->config + SHPC_CMD_STATUS,
 327                                  SHPC_CMD_STATUS_BUSY |
 328                                  SHPC_CMD_STATUS_MRL_OPEN |
 329                                  SHPC_CMD_STATUS_INVALID_CMD |
 330                                  SHPC_CMD_STATUS_INVALID_MODE);
 331     switch (code) {
 332     case 0x00 ... 0x3f:
 333         target = shpc->config[SHPC_CMD_TRGT] & SHPC_CMD_TRGT_MAX;
 334         state = (code & SHPC_SLOT_STATE_MASK) >> SHPC_SLOT_STATE_SHIFT;
 335         power = (code & SHPC_SLOT_PWR_LED_MASK) >> SHPC_SLOT_PWR_LED_SHIFT;
 336         attn = (code & SHPC_SLOT_ATTN_LED_MASK) >> SHPC_SLOT_ATTN_LED_SHIFT;
 337         shpc_slot_command(shpc, target, state, power, attn);
 338         break;
 339     case 0x40 ... 0x47:
 340         speed = code & SHPC_SEC_BUS_MASK;
 341         shpc_set_sec_bus_speed(shpc, speed);
 342         break;
 343     case 0x48:
 344         /* Power only all slots */
 345         /* first verify no slots are enabled */
 346         for (i = 0; i < shpc->nslots; ++i) {
 347             state = shpc_get_status(shpc, i, SHPC_SLOT_STATE_MASK);
 348             if (state == SHPC_STATE_ENABLED) {
 349                 shpc_invalid_command(shpc);
 350                 goto done;
 351             }
 352         }
 353         for (i = 0; i < shpc->nslots; ++i) {
 354             if (!(shpc_get_status(shpc, i, SHPC_SLOT_STATUS_MRL_OPEN))) {
 355                 shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
 356                                   SHPC_STATE_PWRONLY, SHPC_LED_ON, SHPC_LED_NO);
 357             } else {
 358                 shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
 359                                   SHPC_STATE_NO, SHPC_LED_OFF, SHPC_LED_NO);
 360             }
 361         }
 362         break;
 363     case 0x49:
 364         /* Enable all slots */
 365         /* TODO: Spec says this shall fail if some are already enabled.
 366          * This doesn't make sense - why not? a spec bug? */
 367         for (i = 0; i < shpc->nslots; ++i) {
 368             state = shpc_get_status(shpc, i, SHPC_SLOT_STATE_MASK);
 369             if (state == SHPC_STATE_ENABLED) {
 370                 shpc_invalid_command(shpc);
 371                 goto done;
 372             }
 373         }
 374         for (i = 0; i < shpc->nslots; ++i) {
 375             if (!(shpc_get_status(shpc, i, SHPC_SLOT_STATUS_MRL_OPEN))) {
 376                 shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
 377                                   SHPC_STATE_ENABLED, SHPC_LED_ON, SHPC_LED_NO);
 378             } else {
 379                 shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
 380                                   SHPC_STATE_NO, SHPC_LED_OFF, SHPC_LED_NO);
 381             }
 382         }
 383         break;
 384     default:
 385         shpc_invalid_command(shpc);
 386         break;
 387     }
 388 done:
 389     pci_long_test_and_set_mask(shpc->config + SHPC_SERR_INT, SHPC_CMD_DETECTED);
 390 }
 391
 392 static void shpc_write(PCIDevice *d, unsigned addr, uint64_t val, int l)
 393 {
 394     SHPCDevice *shpc = d->shpc;
 395     int i;
 396     if (addr >= SHPC_SIZEOF(d)) {
 397         return;
 398     }
 399     l = MIN(l, SHPC_SIZEOF(d) - addr);
 400
 401     /* TODO: code duplicated from pci.c */
 402     for (i = 0; i < l; val >>= 8, ++i) {
 403         unsigned a = addr + i;
 404         uint8_t wmask = shpc->wmask[a];
 405         uint8_t w1cmask = shpc->w1cmask[a];
 406         assert(!(wmask & w1cmask));
 407         shpc->config[a] = (shpc->config[a] & ~wmask) | (val & wmask);
 408         shpc->config[a] &= ~(val & w1cmask); /* W1C: Write 1 to Clear */
 409     }
 410     if (ranges_overlap(addr, l, SHPC_CMD_CODE, 2)) {
 411         shpc_command(shpc);
 412     }
 413     shpc_interrupt_update(d);
 414 }
 415
 416 static uint64_t shpc_read(PCIDevice *d, unsigned addr, int l)
 417 {
 418     uint64_t val = 0x0;
 419     if (addr >= SHPC_SIZEOF(d)) {
 420         return val;
 421     }
 422     l = MIN(l, SHPC_SIZEOF(d) - addr);
 423     memcpy(&val, d->shpc->config + addr, l);
 424     return val;
 425 }
 426
 427 /* SHPC Bridge Capability */
 428 #define SHPC_CAP_LENGTH 0x08
 429 #define SHPC_CAP_DWORD_SELECT 0x2 /* 1 byte */
 430 #define SHPC_CAP_CxP 0x3 /* 1 byte: CSP, CIP */
 431 #define SHPC_CAP_DWORD_DATA 0x4 /* 4 bytes */
 432 #define SHPC_CAP_CSP_MASK 0x4
 433 #define SHPC_CAP_CIP_MASK 0x8
 434
 435 static uint8_t shpc_cap_dword(PCIDevice *d)
 436 {
 437     return pci_get_byte(d->config + d->shpc->cap + SHPC_CAP_DWORD_SELECT);
 438 }
 439
 440 /* Update dword data capability register */
 441 static void shpc_cap_update_dword(PCIDevice *d)
 442 {
 443     unsigned data;
 444     data = shpc_read(d, shpc_cap_dword(d) * 4, 4);
 445     pci_set_long(d->config  + d->shpc->cap + SHPC_CAP_DWORD_DATA, data);
 446 }
 447
 448 /* Add SHPC capability to the config space for the device. */
 449 static int shpc_cap_add_config(PCIDevice *d)
 450 {
 451     uint8_t *config;
 452     int config_offset;
 453     config_offset = pci_add_capability(d, PCI_CAP_ID_SHPC,
 454                                        0, SHPC_CAP_LENGTH);
 455     if (config_offset < 0) {
 456         return config_offset;
 457     }
 458     config = d->config + config_offset;
 459
 460     pci_set_byte(config + SHPC_CAP_DWORD_SELECT, 0);
 461     pci_set_byte(config + SHPC_CAP_CxP, 0);
 462     pci_set_long(config + SHPC_CAP_DWORD_DATA, 0);
 463     d->shpc->cap = config_offset;
 464     /* Make dword select and data writeable. */
 465     pci_set_byte(d->wmask + config_offset + SHPC_CAP_DWORD_SELECT, 0xff);
 466     pci_set_long(d->wmask + config_offset + SHPC_CAP_DWORD_DATA, 0xffffffff);
 467     return 0;
 468 }
 469
 470 static uint64_t shpc_mmio_read(void *opaque, hwaddr addr,
 471                                unsigned size)
 472 {
 473     return shpc_read(opaque, addr, size);
 474 }
 475
 476 static void shpc_mmio_write(void *opaque, hwaddr addr,
 477                             uint64_t val, unsigned size)
 478 {
 479     shpc_write(opaque, addr, val, size);
 480 }
 481
 482 static const MemoryRegionOps shpc_mmio_ops = {
 483     .read = shpc_mmio_read,
 484     .write = shpc_mmio_write,
 485     .endianness = DEVICE_LITTLE_ENDIAN,
 486     .valid = {
 487         /* SHPC ECN requires dword accesses, but the original 1.0 spec doesn't.
 488          * It's easier to suppport all sizes than worry about it. */
 489         .min_access_size = 1,
 490         .max_access_size = 4,
 491     },
 492 };
 493
 494 static int shpc_device_hotplug(DeviceState *qdev, PCIDevice *affected_dev,
 495                                PCIHotplugState hotplug_state)
 496 {
 497     int pci_slot = PCI_SLOT(affected_dev->devfn);
 498     uint8_t state;
 499     uint8_t led;
 500     PCIDevice *d = DO_UPCAST(PCIDevice, qdev, qdev);
 501     SHPCDevice *shpc = d->shpc;
 502     int slot = SHPC_PCI_TO_IDX(pci_slot);
 503     if (pci_slot < SHPC_IDX_TO_PCI(0) || slot >= shpc->nslots) {
 504         error_report("Unsupported PCI slot %d for standard hotplug "
 505                      "controller. Valid slots are between %d and %d.",
 506                      pci_slot, SHPC_IDX_TO_PCI(0),
 507                      SHPC_IDX_TO_PCI(shpc->nslots) - 1);
 508         return -1;
 509     }
 510     /* Don't send event when device is enabled during qemu machine creation:
 511      * it is present on boot, no hotplug event is necessary. We do send an
 512      * event when the device is disabled later. */
 513     if (hotplug_state == PCI_COLDPLUG_ENABLED) {
 514         shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_MRL_OPEN);
 515         shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_7_5W,
 516                         SHPC_SLOT_STATUS_PRSNT_MASK);
 517         return 0;
 518     }
 519     if (hotplug_state == PCI_HOTPLUG_DISABLED) {
 520         shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |= SHPC_SLOT_EVENT_BUTTON;
 521         state = shpc_get_status(shpc, slot, SHPC_SLOT_STATE_MASK);
 522         led = shpc_get_status(shpc, slot, SHPC_SLOT_PWR_LED_MASK);
 523         if (state == SHPC_STATE_DISABLED && led == SHPC_LED_OFF) {
 524             shpc_free_devices_in_slot(shpc, slot);
 525             shpc_set_status(shpc, slot, 1, SHPC_SLOT_STATUS_MRL_OPEN);
 526             shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_EMPTY,
 527                             SHPC_SLOT_STATUS_PRSNT_MASK);
 528             shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
 529                 SHPC_SLOT_EVENT_MRL |
 530                 SHPC_SLOT_EVENT_PRESENCE;
 531         }
 532     } else {
 533         /* This could be a cancellation of the previous removal.
 534          * We check MRL state to figure out. */
 535         if (shpc_get_status(shpc, slot, SHPC_SLOT_STATUS_MRL_OPEN)) {
 536             shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_MRL_OPEN);
 537             shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_7_5W,
 538                             SHPC_SLOT_STATUS_PRSNT_MASK);
 539             shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
 540                 SHPC_SLOT_EVENT_BUTTON |
 541                 SHPC_SLOT_EVENT_MRL |
 542                 SHPC_SLOT_EVENT_PRESENCE;
 543         } else {
 544             /* Press attention button to cancel removal */
 545             shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
 546                 SHPC_SLOT_EVENT_BUTTON;
 547         }
 548     }
 549     shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_66);
 550     shpc_interrupt_update(d);
 551     return 0;
 552 }
 553
 554 /* Initialize the SHPC structure in bridge's BAR. */
 555 int shpc_init(PCIDevice *d, PCIBus *sec_bus, MemoryRegion *bar, unsigned offset)
 556 {
 557     int i, ret;
 558     int nslots = SHPC_MAX_SLOTS; /* TODO: qdev property? */
 559     SHPCDevice *shpc = d->shpc = g_malloc0(sizeof(*d->shpc));
 560     shpc->sec_bus = sec_bus;
 561     ret = shpc_cap_add_config(d);
 562     if (ret) {
 563         g_free(d->shpc);
 564         return ret;
 565     }
 566     if (nslots < SHPC_MIN_SLOTS) {
 567         return 0;
 568     }
 569     if (nslots > SHPC_MAX_SLOTS ||
 570         SHPC_IDX_TO_PCI(nslots) > PCI_SLOT_MAX) {
 571         /* TODO: report an error mesage that makes sense. */
 572         return -EINVAL;
 573     }
 574     shpc->nslots = nslots;
 575     shpc->config = g_malloc0(SHPC_SIZEOF(d));
 576     shpc->cmask = g_malloc0(SHPC_SIZEOF(d));
 577     shpc->wmask = g_malloc0(SHPC_SIZEOF(d));
 578     shpc->w1cmask = g_malloc0(SHPC_SIZEOF(d));
 579
 580     shpc_reset(d);
 581
 582     pci_set_long(shpc->config + SHPC_BASE_OFFSET, offset);
 583
 584     pci_set_byte(shpc->wmask + SHPC_CMD_CODE, 0xff);
 585     pci_set_byte(shpc->wmask + SHPC_CMD_TRGT, SHPC_CMD_TRGT_MAX);
 586     pci_set_byte(shpc->wmask + SHPC_CMD_TRGT, SHPC_CMD_TRGT_MAX);
 587     pci_set_long(shpc->wmask + SHPC_SERR_INT,
 588                  SHPC_INT_DIS |
 589                  SHPC_SERR_DIS |
 590                  SHPC_CMD_INT_DIS |
 591                  SHPC_ARB_SERR_DIS);
 592     pci_set_long(shpc->w1cmask + SHPC_SERR_INT,
 593                  SHPC_CMD_DETECTED |
 594                  SHPC_ARB_DETECTED);
 595     for (i = 0; i < nslots; ++i) {
 596         pci_set_byte(shpc->wmask +
 597                      SHPC_SLOT_EVENT_SERR_INT_DIS(d, i),
 598                      SHPC_SLOT_EVENT_PRESENCE |
 599                      SHPC_SLOT_EVENT_ISOLATED_FAULT |
 600                      SHPC_SLOT_EVENT_BUTTON |
 601                      SHPC_SLOT_EVENT_MRL |
 602                      SHPC_SLOT_EVENT_CONNECTED_FAULT |
 603                      SHPC_SLOT_EVENT_MRL_SERR_DIS |
 604                      SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS);
 605         pci_set_byte(shpc->w1cmask +
 606                      SHPC_SLOT_EVENT_LATCH(i),
 607                      SHPC_SLOT_EVENT_PRESENCE |
 608                      SHPC_SLOT_EVENT_ISOLATED_FAULT |
 609                      SHPC_SLOT_EVENT_BUTTON |
 610                      SHPC_SLOT_EVENT_MRL |
 611                      SHPC_SLOT_EVENT_CONNECTED_FAULT);
 612     }
 613
 614     /* TODO: init cmask */
 615     memory_region_init_io(&shpc->mmio, OBJECT(d), &shpc_mmio_ops,
 616                           d, "shpc-mmio", SHPC_SIZEOF(d));
 617     shpc_cap_update_dword(d);
 618     memory_region_add_subregion(bar, offset, &shpc->mmio);
 619     pci_bus_hotplug(sec_bus, shpc_device_hotplug, &d->qdev);
 620
 621     d->cap_present |= QEMU_PCI_CAP_SHPC;
 622     return 0;
 623 }
 624
 625 int shpc_bar_size(PCIDevice *d)
 626 {
 627     return roundup_pow_of_two(SHPC_SLOT_REG(SHPC_MAX_SLOTS));
 628 }
 629
 630 void shpc_cleanup(PCIDevice *d, MemoryRegion *bar)
 631 {
 632     SHPCDevice *shpc = d->shpc;
 633     d->cap_present &= ~QEMU_PCI_CAP_SHPC;
 634     memory_region_del_subregion(bar, &shpc->mmio);
 635     /* TODO: cleanup config space changes? */
 636     g_free(shpc->config);
 637     g_free(shpc->cmask);
 638     g_free(shpc->wmask);
 639     g_free(shpc->w1cmask);
 640     memory_region_destroy(&shpc->mmio);
 641     g_free(shpc);
 642 }
 643
 644 void shpc_cap_write_config(PCIDevice *d, uint32_t addr, uint32_t val, int l)
 645 {
 646     if (!ranges_overlap(addr, l, d->shpc->cap, SHPC_CAP_LENGTH)) {
 647         return;
 648     }
 649     if (ranges_overlap(addr, l, d->shpc->cap + SHPC_CAP_DWORD_DATA, 4)) {
 650         unsigned dword_data;
 651         dword_data = pci_get_long(d->shpc->config + d->shpc->cap
 652                                   + SHPC_CAP_DWORD_DATA);
 653         shpc_write(d, shpc_cap_dword(d) * 4, dword_data, 4);
 654     }
 655     /* Update cap dword data in case guest is going to read it. */
 656     shpc_cap_update_dword(d);
 657 }
 658
 659 static void shpc_save(QEMUFile *f, void *pv, size_t size)
 660 {
 661     PCIDevice *d = container_of(pv, PCIDevice, shpc);
 662     qemu_put_buffer(f, d->shpc->config, SHPC_SIZEOF(d));
 663 }
 664
 665 static int shpc_load(QEMUFile *f, void *pv, size_t size)
 666 {
 667     PCIDevice *d = container_of(pv, PCIDevice, shpc);
 668     int ret = qemu_get_buffer(f, d->shpc->config, SHPC_SIZEOF(d));
 669     if (ret != SHPC_SIZEOF(d)) {
 670         return -EINVAL;
 671     }
 672     /* Make sure we don't lose notifications. An extra interrupt is harmless. */
 673     d->shpc->msi_requested = 0;
 674     shpc_interrupt_update(d);
 675     return 0;
 676 }
 677
 678 VMStateInfo shpc_vmstate_info = {
 679     .name = "shpc",
 680     .get  = shpc_load,
 681     .put  = shpc_save,
 682 };