hw/lan9118.c

   1 /*
   2  * SMSC LAN9118 Ethernet interface emulation
   3  *
   4  * Copyright (c) 2009 CodeSourcery, LLC.
   5  * Written by Paul Brook
   6  *
   7  * This code is licensed under the GNU GPL v2
   8  *
   9  * Contributions after 2012-01-13 are licensed under the terms of the
  10  * GNU GPL, version 2 or (at your option) any later version.
  11  */
  12
  13 #include "sysbus.h"
  14 #include "net.h"
  15 #include "devices.h"
  16 #include "sysemu.h"
  17 #include "ptimer.h"
  18 /* For crc32 */
  19 #include <zlib.h>
  20
  21 //#define DEBUG_LAN9118
  22
  23 #ifdef DEBUG_LAN9118
  24 #define DPRINTF(fmt, ...) \
  25 do { printf("lan9118: " fmt , ## __VA_ARGS__); } while (0)
  26 #define BADF(fmt, ...) \
  27 do { hw_error("lan9118: error: " fmt , ## __VA_ARGS__);} while (0)
  28 #else
  29 #define DPRINTF(fmt, ...) do {} while(0)
  30 #define BADF(fmt, ...) \
  31 do { fprintf(stderr, "lan9118: error: " fmt , ## __VA_ARGS__);} while (0)
  32 #endif
  33
  34 #define CSR_ID_REV      0x50
  35 #define CSR_IRQ_CFG     0x54
  36 #define CSR_INT_STS     0x58
  37 #define CSR_INT_EN      0x5c
  38 #define CSR_BYTE_TEST   0x64
  39 #define CSR_FIFO_INT    0x68
  40 #define CSR_RX_CFG      0x6c
  41 #define CSR_TX_CFG      0x70
  42 #define CSR_HW_CFG      0x74
  43 #define CSR_RX_DP_CTRL  0x78
  44 #define CSR_RX_FIFO_INF 0x7c
  45 #define CSR_TX_FIFO_INF 0x80
  46 #define CSR_PMT_CTRL    0x84
  47 #define CSR_GPIO_CFG    0x88
  48 #define CSR_GPT_CFG     0x8c
  49 #define CSR_GPT_CNT     0x90
  50 #define CSR_WORD_SWAP   0x98
  51 #define CSR_FREE_RUN    0x9c
  52 #define CSR_RX_DROP     0xa0
  53 #define CSR_MAC_CSR_CMD 0xa4
  54 #define CSR_MAC_CSR_DATA 0xa8
  55 #define CSR_AFC_CFG     0xac
  56 #define CSR_E2P_CMD     0xb0
  57 #define CSR_E2P_DATA    0xb4
  58
  59 /* IRQ_CFG */
  60 #define IRQ_INT         0x00001000
  61 #define IRQ_EN          0x00000100
  62 #define IRQ_POL         0x00000010
  63 #define IRQ_TYPE        0x00000001
  64
  65 /* INT_STS/INT_EN */
  66 #define SW_INT          0x80000000
  67 #define TXSTOP_INT      0x02000000
  68 #define RXSTOP_INT      0x01000000
  69 #define RXDFH_INT       0x00800000
  70 #define TX_IOC_INT      0x00200000
  71 #define RXD_INT         0x00100000
  72 #define GPT_INT         0x00080000
  73 #define PHY_INT         0x00040000
  74 #define PME_INT         0x00020000
  75 #define TXSO_INT        0x00010000
  76 #define RWT_INT         0x00008000
  77 #define RXE_INT         0x00004000
  78 #define TXE_INT         0x00002000
  79 #define TDFU_INT        0x00000800
  80 #define TDFO_INT        0x00000400
  81 #define TDFA_INT        0x00000200
  82 #define TSFF_INT        0x00000100
  83 #define TSFL_INT        0x00000080
  84 #define RXDF_INT        0x00000040
  85 #define RDFL_INT        0x00000020
  86 #define RSFF_INT        0x00000010
  87 #define RSFL_INT        0x00000008
  88 #define GPIO2_INT       0x00000004
  89 #define GPIO1_INT       0x00000002
  90 #define GPIO0_INT       0x00000001
  91 #define RESERVED_INT    0x7c001000
  92
  93 #define MAC_CR          1
  94 #define MAC_ADDRH       2
  95 #define MAC_ADDRL       3
  96 #define MAC_HASHH       4
  97 #define MAC_HASHL       5
  98 #define MAC_MII_ACC     6
  99 #define MAC_MII_DATA    7
 100 #define MAC_FLOW        8
 101 #define MAC_VLAN1       9 /* TODO */
 102 #define MAC_VLAN2       10 /* TODO */
 103 #define MAC_WUFF        11 /* TODO */
 104 #define MAC_WUCSR       12 /* TODO */
 105
 106 #define MAC_CR_RXALL    0x80000000
 107 #define MAC_CR_RCVOWN   0x00800000
 108 #define MAC_CR_LOOPBK   0x00200000
 109 #define MAC_CR_FDPX     0x00100000
 110 #define MAC_CR_MCPAS    0x00080000
 111 #define MAC_CR_PRMS     0x00040000
 112 #define MAC_CR_INVFILT  0x00020000
 113 #define MAC_CR_PASSBAD  0x00010000
 114 #define MAC_CR_HO       0x00008000
 115 #define MAC_CR_HPFILT   0x00002000
 116 #define MAC_CR_LCOLL    0x00001000
 117 #define MAC_CR_BCAST    0x00000800
 118 #define MAC_CR_DISRTY   0x00000400
 119 #define MAC_CR_PADSTR   0x00000100
 120 #define MAC_CR_BOLMT    0x000000c0
 121 #define MAC_CR_DFCHK    0x00000020
 122 #define MAC_CR_TXEN     0x00000008
 123 #define MAC_CR_RXEN     0x00000004
 124 #define MAC_CR_RESERVED 0x7f404213
 125
 126 #define PHY_INT_ENERGYON            0x80
 127 #define PHY_INT_AUTONEG_COMPLETE    0x40
 128 #define PHY_INT_FAULT               0x20
 129 #define PHY_INT_DOWN                0x10
 130 #define PHY_INT_AUTONEG_LP          0x08
 131 #define PHY_INT_PARFAULT            0x04
 132 #define PHY_INT_AUTONEG_PAGE        0x02
 133
 134 #define GPT_TIMER_EN    0x20000000
 135
 136 enum tx_state {
 137     TX_IDLE,
 138     TX_B,
 139     TX_DATA
 140 };
 141
 142 typedef struct {
 143     /* state is a tx_state but we can't put enums in VMStateDescriptions. */
 144     uint32_t state;
 145     uint32_t cmd_a;
 146     uint32_t cmd_b;
 147     int32_t buffer_size;
 148     int32_t offset;
 149     int32_t pad;
 150     int32_t fifo_used;
 151     int32_t len;
 152     uint8_t data[2048];
 153 } LAN9118Packet;
 154
 155 static const VMStateDescription vmstate_lan9118_packet = {
 156     .name = "lan9118_packet",
 157     .version_id = 1,
 158     .minimum_version_id = 1,
 159     .fields = (VMStateField[]) {
 160         VMSTATE_UINT32(state, LAN9118Packet),
 161         VMSTATE_UINT32(cmd_a, LAN9118Packet),
 162         VMSTATE_UINT32(cmd_b, LAN9118Packet),
 163         VMSTATE_INT32(buffer_size, LAN9118Packet),
 164         VMSTATE_INT32(offset, LAN9118Packet),
 165         VMSTATE_INT32(pad, LAN9118Packet),
 166         VMSTATE_INT32(fifo_used, LAN9118Packet),
 167         VMSTATE_INT32(len, LAN9118Packet),
 168         VMSTATE_UINT8_ARRAY(data, LAN9118Packet, 2048),
 169         VMSTATE_END_OF_LIST()
 170     }
 171 };
 172
 173 typedef struct {
 174     SysBusDevice busdev;
 175     NICState *nic;
 176     NICConf conf;
 177     qemu_irq irq;
 178     MemoryRegion mmio;
 179     ptimer_state *timer;
 180
 181     uint32_t irq_cfg;
 182     uint32_t int_sts;
 183     uint32_t int_en;
 184     uint32_t fifo_int;
 185     uint32_t rx_cfg;
 186     uint32_t tx_cfg;
 187     uint32_t hw_cfg;
 188     uint32_t pmt_ctrl;
 189     uint32_t gpio_cfg;
 190     uint32_t gpt_cfg;
 191     uint32_t word_swap;
 192     uint32_t free_timer_start;
 193     uint32_t mac_cmd;
 194     uint32_t mac_data;
 195     uint32_t afc_cfg;
 196     uint32_t e2p_cmd;
 197     uint32_t e2p_data;
 198
 199     uint32_t mac_cr;
 200     uint32_t mac_hashh;
 201     uint32_t mac_hashl;
 202     uint32_t mac_mii_acc;
 203     uint32_t mac_mii_data;
 204     uint32_t mac_flow;
 205
 206     uint32_t phy_status;
 207     uint32_t phy_control;
 208     uint32_t phy_advertise;
 209     uint32_t phy_int;
 210     uint32_t phy_int_mask;
 211
 212     int32_t eeprom_writable;
 213     uint8_t eeprom[128];
 214
 215     int32_t tx_fifo_size;
 216     LAN9118Packet *txp;
 217     LAN9118Packet tx_packet;
 218
 219     int32_t tx_status_fifo_used;
 220     int32_t tx_status_fifo_head;
 221     uint32_t tx_status_fifo[512];
 222
 223     int32_t rx_status_fifo_size;
 224     int32_t rx_status_fifo_used;
 225     int32_t rx_status_fifo_head;
 226     uint32_t rx_status_fifo[896];
 227     int32_t rx_fifo_size;
 228     int32_t rx_fifo_used;
 229     int32_t rx_fifo_head;
 230     uint32_t rx_fifo[3360];
 231     int32_t rx_packet_size_head;
 232     int32_t rx_packet_size_tail;
 233     int32_t rx_packet_size[1024];
 234
 235     int32_t rxp_offset;
 236     int32_t rxp_size;
 237     int32_t rxp_pad;
 238
 239     uint32_t write_word_prev_offset;
 240     uint32_t write_word_n;
 241     uint16_t write_word_l;
 242     uint16_t write_word_h;
 243     uint32_t read_word_prev_offset;
 244     uint32_t read_word_n;
 245     uint32_t read_long;
 246
 247     uint32_t mode_16bit;
 248 } lan9118_state;
 249
 250 static const VMStateDescription vmstate_lan9118 = {
 251     .name = "lan9118",
 252     .version_id = 2,
 253     .minimum_version_id = 1,
 254     .fields = (VMStateField[]) {
 255         VMSTATE_PTIMER(timer, lan9118_state),
 256         VMSTATE_UINT32(irq_cfg, lan9118_state),
 257         VMSTATE_UINT32(int_sts, lan9118_state),
 258         VMSTATE_UINT32(int_en, lan9118_state),
 259         VMSTATE_UINT32(fifo_int, lan9118_state),
 260         VMSTATE_UINT32(rx_cfg, lan9118_state),
 261         VMSTATE_UINT32(tx_cfg, lan9118_state),
 262         VMSTATE_UINT32(hw_cfg, lan9118_state),
 263         VMSTATE_UINT32(pmt_ctrl, lan9118_state),
 264         VMSTATE_UINT32(gpio_cfg, lan9118_state),
 265         VMSTATE_UINT32(gpt_cfg, lan9118_state),
 266         VMSTATE_UINT32(word_swap, lan9118_state),
 267         VMSTATE_UINT32(free_timer_start, lan9118_state),
 268         VMSTATE_UINT32(mac_cmd, lan9118_state),
 269         VMSTATE_UINT32(mac_data, lan9118_state),
 270         VMSTATE_UINT32(afc_cfg, lan9118_state),
 271         VMSTATE_UINT32(e2p_cmd, lan9118_state),
 272         VMSTATE_UINT32(e2p_data, lan9118_state),
 273         VMSTATE_UINT32(mac_cr, lan9118_state),
 274         VMSTATE_UINT32(mac_hashh, lan9118_state),
 275         VMSTATE_UINT32(mac_hashl, lan9118_state),
 276         VMSTATE_UINT32(mac_mii_acc, lan9118_state),
 277         VMSTATE_UINT32(mac_mii_data, lan9118_state),
 278         VMSTATE_UINT32(mac_flow, lan9118_state),
 279         VMSTATE_UINT32(phy_status, lan9118_state),
 280         VMSTATE_UINT32(phy_control, lan9118_state),
 281         VMSTATE_UINT32(phy_advertise, lan9118_state),
 282         VMSTATE_UINT32(phy_int, lan9118_state),
 283         VMSTATE_UINT32(phy_int_mask, lan9118_state),
 284         VMSTATE_INT32(eeprom_writable, lan9118_state),
 285         VMSTATE_UINT8_ARRAY(eeprom, lan9118_state, 128),
 286         VMSTATE_INT32(tx_fifo_size, lan9118_state),
 287         /* txp always points at tx_packet so need not be saved */
 288         VMSTATE_STRUCT(tx_packet, lan9118_state, 0,
 289                        vmstate_lan9118_packet, LAN9118Packet),
 290         VMSTATE_INT32(tx_status_fifo_used, lan9118_state),
 291         VMSTATE_INT32(tx_status_fifo_head, lan9118_state),
 292         VMSTATE_UINT32_ARRAY(tx_status_fifo, lan9118_state, 512),
 293         VMSTATE_INT32(rx_status_fifo_size, lan9118_state),
 294         VMSTATE_INT32(rx_status_fifo_used, lan9118_state),
 295         VMSTATE_INT32(rx_status_fifo_head, lan9118_state),
 296         VMSTATE_UINT32_ARRAY(rx_status_fifo, lan9118_state, 896),
 297         VMSTATE_INT32(rx_fifo_size, lan9118_state),
 298         VMSTATE_INT32(rx_fifo_used, lan9118_state),
 299         VMSTATE_INT32(rx_fifo_head, lan9118_state),
 300         VMSTATE_UINT32_ARRAY(rx_fifo, lan9118_state, 3360),
 301         VMSTATE_INT32(rx_packet_size_head, lan9118_state),
 302         VMSTATE_INT32(rx_packet_size_tail, lan9118_state),
 303         VMSTATE_INT32_ARRAY(rx_packet_size, lan9118_state, 1024),
 304         VMSTATE_INT32(rxp_offset, lan9118_state),
 305         VMSTATE_INT32(rxp_size, lan9118_state),
 306         VMSTATE_INT32(rxp_pad, lan9118_state),
 307         VMSTATE_UINT32_V(write_word_prev_offset, lan9118_state, 2),
 308         VMSTATE_UINT32_V(write_word_n, lan9118_state, 2),
 309         VMSTATE_UINT16_V(write_word_l, lan9118_state, 2),
 310         VMSTATE_UINT16_V(write_word_h, lan9118_state, 2),
 311         VMSTATE_UINT32_V(read_word_prev_offset, lan9118_state, 2),
 312         VMSTATE_UINT32_V(read_word_n, lan9118_state, 2),
 313         VMSTATE_UINT32_V(read_long, lan9118_state, 2),
 314         VMSTATE_UINT32_V(mode_16bit, lan9118_state, 2),
 315         VMSTATE_END_OF_LIST()
 316     }
 317 };
 318
 319 static void lan9118_update(lan9118_state *s)
 320 {
 321     int level;
 322
 323     /* TODO: Implement FIFO level IRQs.  */
 324     level = (s->int_sts & s->int_en) != 0;
 325     if (level) {
 326         s->irq_cfg |= IRQ_INT;
 327     } else {
 328         s->irq_cfg &= ~IRQ_INT;
 329     }
 330     if ((s->irq_cfg & IRQ_EN) == 0) {
 331         level = 0;
 332     }
 333     if ((s->irq_cfg & (IRQ_TYPE | IRQ_POL)) != (IRQ_TYPE | IRQ_POL)) {
 334         /* Interrupt is active low unless we're configured as
 335          * active-high polarity, push-pull type.
 336          */
 337         level = !level;
 338     }
 339     qemu_set_irq(s->irq, level);
 340 }
 341
 342 static void lan9118_mac_changed(lan9118_state *s)
 343 {
 344     qemu_format_nic_info_str(&s->nic->nc, s->conf.macaddr.a);
 345 }
 346
 347 static void lan9118_reload_eeprom(lan9118_state *s)
 348 {
 349     int i;
 350     if (s->eeprom[0] != 0xa5) {
 351         s->e2p_cmd &= ~0x10;
 352         DPRINTF("MACADDR load failed\n");
 353         return;
 354     }
 355     for (i = 0; i < 6; i++) {
 356         s->conf.macaddr.a[i] = s->eeprom[i + 1];
 357     }
 358     s->e2p_cmd |= 0x10;
 359     DPRINTF("MACADDR loaded from eeprom\n");
 360     lan9118_mac_changed(s);
 361 }
 362
 363 static void phy_update_irq(lan9118_state *s)
 364 {
 365     if (s->phy_int & s->phy_int_mask) {
 366         s->int_sts |= PHY_INT;
 367     } else {
 368         s->int_sts &= ~PHY_INT;
 369     }
 370     lan9118_update(s);
 371 }
 372
 373 static void phy_update_link(lan9118_state *s)
 374 {
 375     /* Autonegotiation status mirrors link status.  */
 376     if (s->nic->nc.link_down) {
 377         s->phy_status &= ~0x0024;
 378         s->phy_int |= PHY_INT_DOWN;
 379     } else {
 380         s->phy_status |= 0x0024;
 381         s->phy_int |= PHY_INT_ENERGYON;
 382         s->phy_int |= PHY_INT_AUTONEG_COMPLETE;
 383     }
 384     phy_update_irq(s);
 385 }
 386
 387 static void lan9118_set_link(NetClientState *nc)
 388 {
 389     phy_update_link(DO_UPCAST(NICState, nc, nc)->opaque);
 390 }
 391
 392 static void phy_reset(lan9118_state *s)
 393 {
 394     s->phy_status = 0x7809;
 395     s->phy_control = 0x3000;
 396     s->phy_advertise = 0x01e1;
 397     s->phy_int_mask = 0;
 398     s->phy_int = 0;
 399     phy_update_link(s);
 400 }
 401
 402 static void lan9118_reset(DeviceState *d)
 403 {
 404     lan9118_state *s = FROM_SYSBUS(lan9118_state, sysbus_from_qdev(d));
 405     s->irq_cfg &= (IRQ_TYPE | IRQ_POL);
 406     s->int_sts = 0;
 407     s->int_en = 0;
 408     s->fifo_int = 0x48000000;
 409     s->rx_cfg = 0;
 410     s->tx_cfg = 0;
 411     s->hw_cfg = s->mode_16bit ? 0x00050000 : 0x00050004;
 412     s->pmt_ctrl &= 0x45;
 413     s->gpio_cfg = 0;
 414     s->txp->fifo_used = 0;
 415     s->txp->state = TX_IDLE;
 416     s->txp->cmd_a = 0xffffffffu;
 417     s->txp->cmd_b = 0xffffffffu;
 418     s->txp->len = 0;
 419     s->txp->fifo_used = 0;
 420     s->tx_fifo_size = 4608;
 421     s->tx_status_fifo_used = 0;
 422     s->rx_status_fifo_size = 704;
 423     s->rx_fifo_size = 2640;
 424     s->rx_fifo_used = 0;
 425     s->rx_status_fifo_size = 176;
 426     s->rx_status_fifo_used = 0;
 427     s->rxp_offset = 0;
 428     s->rxp_size = 0;
 429     s->rxp_pad = 0;
 430     s->rx_packet_size_tail = s->rx_packet_size_head;
 431     s->rx_packet_size[s->rx_packet_size_head] = 0;
 432     s->mac_cmd = 0;
 433     s->mac_data = 0;
 434     s->afc_cfg = 0;
 435     s->e2p_cmd = 0;
 436     s->e2p_data = 0;
 437     s->free_timer_start = qemu_get_clock_ns(vm_clock) / 40;
 438
 439     ptimer_stop(s->timer);
 440     ptimer_set_count(s->timer, 0xffff);
 441     s->gpt_cfg = 0xffff;
 442
 443     s->mac_cr = MAC_CR_PRMS;
 444     s->mac_hashh = 0;
 445     s->mac_hashl = 0;
 446     s->mac_mii_acc = 0;
 447     s->mac_mii_data = 0;
 448     s->mac_flow = 0;
 449
 450     s->read_word_n = 0;
 451     s->write_word_n = 0;
 452
 453     phy_reset(s);
 454
 455     s->eeprom_writable = 0;
 456     lan9118_reload_eeprom(s);
 457 }
 458
 459 static int lan9118_can_receive(NetClientState *nc)
 460 {
 461     return 1;
 462 }
 463
 464 static void rx_fifo_push(lan9118_state *s, uint32_t val)
 465 {
 466     int fifo_pos;
 467     fifo_pos = s->rx_fifo_head + s->rx_fifo_used;
 468     if (fifo_pos >= s->rx_fifo_size)
 469       fifo_pos -= s->rx_fifo_size;
 470     s->rx_fifo[fifo_pos] = val;
 471     s->rx_fifo_used++;
 472 }
 473
 474 /* Return nonzero if the packet is accepted by the filter.  */
 475 static int lan9118_filter(lan9118_state *s, const uint8_t *addr)
 476 {
 477     int multicast;
 478     uint32_t hash;
 479
 480     if (s->mac_cr & MAC_CR_PRMS) {
 481         return 1;
 482     }
 483     if (addr[0] == 0xff && addr[1] == 0xff && addr[2] == 0xff &&
 484         addr[3] == 0xff && addr[4] == 0xff && addr[5] == 0xff) {
 485         return (s->mac_cr & MAC_CR_BCAST) == 0;
 486     }
 487
 488     multicast = addr[0] & 1;
 489     if (multicast &&s->mac_cr & MAC_CR_MCPAS) {
 490         return 1;
 491     }
 492     if (multicast ? (s->mac_cr & MAC_CR_HPFILT) == 0
 493                   : (s->mac_cr & MAC_CR_HO) == 0) {
 494         /* Exact matching.  */
 495         hash = memcmp(addr, s->conf.macaddr.a, 6);
 496         if (s->mac_cr & MAC_CR_INVFILT) {
 497             return hash != 0;
 498         } else {
 499             return hash == 0;
 500         }
 501     } else {
 502         /* Hash matching  */
 503         hash = (crc32(~0, addr, 6) >> 26);
 504         if (hash & 0x20) {
 505             return (s->mac_hashh >> (hash & 0x1f)) & 1;
 506         } else {
 507             return (s->mac_hashl >> (hash & 0x1f)) & 1;
 508         }
 509     }
 510 }
 511
 512 static ssize_t lan9118_receive(NetClientState *nc, const uint8_t *buf,
 513                                size_t size)
 514 {
 515     lan9118_state *s = DO_UPCAST(NICState, nc, nc)->opaque;
 516     int fifo_len;
 517     int offset;
 518     int src_pos;
 519     int n;
 520     int filter;
 521     uint32_t val;
 522     uint32_t crc;
 523     uint32_t status;
 524
 525     if ((s->mac_cr & MAC_CR_RXEN) == 0) {
 526         return -1;
 527     }
 528
 529     if (size >= 2048 || size < 14) {
 530         return -1;
 531     }
 532
 533     /* TODO: Implement FIFO overflow notification.  */
 534     if (s->rx_status_fifo_used == s->rx_status_fifo_size) {
 535         return -1;
 536     }
 537
 538     filter = lan9118_filter(s, buf);
 539     if (!filter && (s->mac_cr & MAC_CR_RXALL) == 0) {
 540         return size;
 541     }
 542
 543     offset = (s->rx_cfg >> 8) & 0x1f;
 544     n = offset & 3;
 545     fifo_len = (size + n + 3) >> 2;
 546     /* Add a word for the CRC.  */
 547     fifo_len++;
 548     if (s->rx_fifo_size - s->rx_fifo_used < fifo_len) {
 549         return -1;
 550     }
 551
 552     DPRINTF("Got packet len:%d fifo:%d filter:%s\n",
 553             (int)size, fifo_len, filter ? "pass" : "fail");
 554     val = 0;
 555     crc = bswap32(crc32(~0, buf, size));
 556     for (src_pos = 0; src_pos < size; src_pos++) {
 557         val = (val >> 8) | ((uint32_t)buf[src_pos] << 24);
 558         n++;
 559         if (n == 4) {
 560             n = 0;
 561             rx_fifo_push(s, val);
 562             val = 0;
 563         }
 564     }
 565     if (n) {
 566         val >>= ((4 - n) * 8);
 567         val |= crc << (n * 8);
 568         rx_fifo_push(s, val);
 569         val = crc >> ((4 - n) * 8);
 570         rx_fifo_push(s, val);
 571     } else {
 572         rx_fifo_push(s, crc);
 573     }
 574     n = s->rx_status_fifo_head + s->rx_status_fifo_used;
 575     if (n >= s->rx_status_fifo_size) {
 576         n -= s->rx_status_fifo_size;
 577     }
 578     s->rx_packet_size[s->rx_packet_size_tail] = fifo_len;
 579     s->rx_packet_size_tail = (s->rx_packet_size_tail + 1023) & 1023;
 580     s->rx_status_fifo_used++;
 581
 582     status = (size + 4) << 16;
 583     if (buf[0] == 0xff && buf[1] == 0xff && buf[2] == 0xff &&
 584         buf[3] == 0xff && buf[4] == 0xff && buf[5] == 0xff) {
 585         status |= 0x00002000;
 586     } else if (buf[0] & 1) {
 587         status |= 0x00000400;
 588     }
 589     if (!filter) {
 590         status |= 0x40000000;
 591     }
 592     s->rx_status_fifo[n] = status;
 593
 594     if (s->rx_status_fifo_used > (s->fifo_int & 0xff)) {
 595         s->int_sts |= RSFL_INT;
 596     }
 597     lan9118_update(s);
 598
 599     return size;
 600 }
 601
 602 static uint32_t rx_fifo_pop(lan9118_state *s)
 603 {
 604     int n;
 605     uint32_t val;
 606
 607     if (s->rxp_size == 0 && s->rxp_pad == 0) {
 608         s->rxp_size = s->rx_packet_size[s->rx_packet_size_head];
 609         s->rx_packet_size[s->rx_packet_size_head] = 0;
 610         if (s->rxp_size != 0) {
 611             s->rx_packet_size_head = (s->rx_packet_size_head + 1023) & 1023;
 612             s->rxp_offset = (s->rx_cfg >> 10) & 7;
 613             n = s->rxp_offset + s->rxp_size;
 614             switch (s->rx_cfg >> 30) {
 615             case 1:
 616                 n = (-n) & 3;
 617                 break;
 618             case 2:
 619                 n = (-n) & 7;
 620                 break;
 621             default:
 622                 n = 0;
 623                 break;
 624             }
 625             s->rxp_pad = n;
 626             DPRINTF("Pop packet size:%d offset:%d pad: %d\n",
 627                     s->rxp_size, s->rxp_offset, s->rxp_pad);
 628         }
 629     }
 630     if (s->rxp_offset > 0) {
 631         s->rxp_offset--;
 632         val = 0;
 633     } else if (s->rxp_size > 0) {
 634         s->rxp_size--;
 635         val = s->rx_fifo[s->rx_fifo_head++];
 636         if (s->rx_fifo_head >= s->rx_fifo_size) {
 637             s->rx_fifo_head -= s->rx_fifo_size;
 638         }
 639         s->rx_fifo_used--;
 640     } else if (s->rxp_pad > 0) {
 641         s->rxp_pad--;
 642         val =  0;
 643     } else {
 644         DPRINTF("RX underflow\n");
 645         s->int_sts |= RXE_INT;
 646         val =  0;
 647     }
 648     lan9118_update(s);
 649     return val;
 650 }
 651
 652 static void do_tx_packet(lan9118_state *s)
 653 {
 654     int n;
 655     uint32_t status;
 656
 657     /* FIXME: Honor TX disable, and allow queueing of packets.  */
 658     if (s->phy_control & 0x4000)  {
 659         /* This assumes the receive routine doesn't touch the VLANClient.  */
 660         lan9118_receive(&s->nic->nc, s->txp->data, s->txp->len);
 661     } else {
 662         qemu_send_packet(&s->nic->nc, s->txp->data, s->txp->len);
 663     }
 664     s->txp->fifo_used = 0;
 665
 666     if (s->tx_status_fifo_used == 512) {
 667         /* Status FIFO full */
 668         return;
 669     }
 670     /* Add entry to status FIFO.  */
 671     status = s->txp->cmd_b & 0xffff0000u;
 672     DPRINTF("Sent packet tag:%04x len %d\n", status >> 16, s->txp->len);
 673     n = (s->tx_status_fifo_head + s->tx_status_fifo_used) & 511;
 674     s->tx_status_fifo[n] = status;
 675     s->tx_status_fifo_used++;
 676     if (s->tx_status_fifo_used == 512) {
 677         s->int_sts |= TSFF_INT;
 678         /* TODO: Stop transmission.  */
 679     }
 680 }
 681
 682 static uint32_t rx_status_fifo_pop(lan9118_state *s)
 683 {
 684     uint32_t val;
 685
 686     val = s->rx_status_fifo[s->rx_status_fifo_head];
 687     if (s->rx_status_fifo_used != 0) {
 688         s->rx_status_fifo_used--;
 689         s->rx_status_fifo_head++;
 690         if (s->rx_status_fifo_head >= s->rx_status_fifo_size) {
 691             s->rx_status_fifo_head -= s->rx_status_fifo_size;
 692         }
 693         /* ??? What value should be returned when the FIFO is empty?  */
 694         DPRINTF("RX status pop 0x%08x\n", val);
 695     }
 696     return val;
 697 }
 698
 699 static uint32_t tx_status_fifo_pop(lan9118_state *s)
 700 {
 701     uint32_t val;
 702
 703     val = s->tx_status_fifo[s->tx_status_fifo_head];
 704     if (s->tx_status_fifo_used != 0) {
 705         s->tx_status_fifo_used--;
 706         s->tx_status_fifo_head = (s->tx_status_fifo_head + 1) & 511;
 707         /* ??? What value should be returned when the FIFO is empty?  */
 708     }
 709     return val;
 710 }
 711
 712 static void tx_fifo_push(lan9118_state *s, uint32_t val)
 713 {
 714     int n;
 715
 716     if (s->txp->fifo_used == s->tx_fifo_size) {
 717         s->int_sts |= TDFO_INT;
 718         return;
 719     }
 720     switch (s->txp->state) {
 721     case TX_IDLE:
 722         s->txp->cmd_a = val & 0x831f37ff;
 723         s->txp->fifo_used++;
 724         s->txp->state = TX_B;
 725         break;
 726     case TX_B:
 727         if (s->txp->cmd_a & 0x2000) {
 728             /* First segment */
 729             s->txp->cmd_b = val;
 730             s->txp->fifo_used++;
 731             s->txp->buffer_size = s->txp->cmd_a & 0x7ff;
 732             s->txp->offset = (s->txp->cmd_a >> 16) & 0x1f;
 733             /* End alignment does not include command words.  */
 734             n = (s->txp->buffer_size + s->txp->offset + 3) >> 2;
 735             switch ((n >> 24) & 3) {
 736             case 1:
 737                 n = (-n) & 3;
 738                 break;
 739             case 2:
 740                 n = (-n) & 7;
 741                 break;
 742             default:
 743                 n = 0;
 744             }
 745             s->txp->pad = n;
 746             s->txp->len = 0;
 747         }
 748         DPRINTF("Block len:%d offset:%d pad:%d cmd %08x\n",
 749                 s->txp->buffer_size, s->txp->offset, s->txp->pad,
 750                 s->txp->cmd_a);
 751         s->txp->state = TX_DATA;
 752         break;
 753     case TX_DATA:
 754         if (s->txp->offset >= 4) {
 755             s->txp->offset -= 4;
 756             break;
 757         }
 758         if (s->txp->buffer_size <= 0 && s->txp->pad != 0) {
 759             s->txp->pad--;
 760         } else {
 761             n = 4;
 762             while (s->txp->offset) {
 763                 val >>= 8;
 764                 n--;
 765                 s->txp->offset--;
 766             }
 767             /* Documentation is somewhat unclear on the ordering of bytes
 768                in FIFO words.  Empirical results show it to be little-endian.
 769                */
 770             /* TODO: FIFO overflow checking.  */
 771             while (n--) {
 772                 s->txp->data[s->txp->len] = val & 0xff;
 773                 s->txp->len++;
 774                 val >>= 8;
 775                 s->txp->buffer_size--;
 776             }
 777             s->txp->fifo_used++;
 778         }
 779         if (s->txp->buffer_size <= 0 && s->txp->pad == 0) {
 780             if (s->txp->cmd_a & 0x1000) {
 781                 do_tx_packet(s);
 782             }
 783             if (s->txp->cmd_a & 0x80000000) {
 784                 s->int_sts |= TX_IOC_INT;
 785             }
 786             s->txp->state = TX_IDLE;
 787         }
 788         break;
 789     }
 790 }
 791
 792 static uint32_t do_phy_read(lan9118_state *s, int reg)
 793 {
 794     uint32_t val;
 795
 796     switch (reg) {
 797     case 0: /* Basic Control */
 798         return s->phy_control;
 799     case 1: /* Basic Status */
 800         return s->phy_status;
 801     case 2: /* ID1 */
 802         return 0x0007;
 803     case 3: /* ID2 */
 804         return 0xc0d1;
 805     case 4: /* Auto-neg advertisement */
 806         return s->phy_advertise;
 807     case 5: /* Auto-neg Link Partner Ability */
 808         return 0x0f71;
 809     case 6: /* Auto-neg Expansion */
 810         return 1;
 811         /* TODO 17, 18, 27, 29, 30, 31 */
 812     case 29: /* Interrupt source.  */
 813         val = s->phy_int;
 814         s->phy_int = 0;
 815         phy_update_irq(s);
 816         return val;
 817     case 30: /* Interrupt mask */
 818         return s->phy_int_mask;
 819     default:
 820         BADF("PHY read reg %d\n", reg);
 821         return 0;
 822     }
 823 }
 824
 825 static void do_phy_write(lan9118_state *s, int reg, uint32_t val)
 826 {
 827     switch (reg) {
 828     case 0: /* Basic Control */
 829         if (val & 0x8000) {
 830             phy_reset(s);
 831             break;
 832         }
 833         s->phy_control = val & 0x7980;
 834         /* Complete autonegotiation immediately.  */
 835         if (val & 0x1000) {
 836             s->phy_status |= 0x0020;
 837         }
 838         break;
 839     case 4: /* Auto-neg advertisement */
 840         s->phy_advertise = (val & 0x2d7f) | 0x80;
 841         break;
 842         /* TODO 17, 18, 27, 31 */
 843     case 30: /* Interrupt mask */
 844         s->phy_int_mask = val & 0xff;
 845         phy_update_irq(s);
 846         break;
 847     default:
 848         BADF("PHY write reg %d = 0x%04x\n", reg, val);
 849     }
 850 }
 851
 852 static void do_mac_write(lan9118_state *s, int reg, uint32_t val)
 853 {
 854     switch (reg) {
 855     case MAC_CR:
 856         if ((s->mac_cr & MAC_CR_RXEN) != 0 && (val & MAC_CR_RXEN) == 0) {
 857             s->int_sts |= RXSTOP_INT;
 858         }
 859         s->mac_cr = val & ~MAC_CR_RESERVED;
 860         DPRINTF("MAC_CR: %08x\n", val);
 861         break;
 862     case MAC_ADDRH:
 863         s->conf.macaddr.a[4] = val & 0xff;
 864         s->conf.macaddr.a[5] = (val >> 8) & 0xff;
 865         lan9118_mac_changed(s);
 866         break;
 867     case MAC_ADDRL:
 868         s->conf.macaddr.a[0] = val & 0xff;
 869         s->conf.macaddr.a[1] = (val >> 8) & 0xff;
 870         s->conf.macaddr.a[2] = (val >> 16) & 0xff;
 871         s->conf.macaddr.a[3] = (val >> 24) & 0xff;
 872         lan9118_mac_changed(s);
 873         break;
 874     case MAC_HASHH:
 875         s->mac_hashh = val;
 876         break;
 877     case MAC_HASHL:
 878         s->mac_hashl = val;
 879         break;
 880     case MAC_MII_ACC:
 881         s->mac_mii_acc = val & 0xffc2;
 882         if (val & 2) {
 883             DPRINTF("PHY write %d = 0x%04x\n",
 884                     (val >> 6) & 0x1f, s->mac_mii_data);
 885             do_phy_write(s, (val >> 6) & 0x1f, s->mac_mii_data);
 886         } else {
 887             s->mac_mii_data = do_phy_read(s, (val >> 6) & 0x1f);
 888             DPRINTF("PHY read %d = 0x%04x\n",
 889                     (val >> 6) & 0x1f, s->mac_mii_data);
 890         }
 891         break;
 892     case MAC_MII_DATA:
 893         s->mac_mii_data = val & 0xffff;
 894         break;
 895     case MAC_FLOW:
 896         s->mac_flow = val & 0xffff0000;
 897         break;
 898     case MAC_VLAN1:
 899         /* Writing to this register changes a condition for
 900          * FrameTooLong bit in rx_status.  Since we do not set
 901          * FrameTooLong anyway, just ignore write to this.
 902          */
 903         break;
 904     default:
 905         hw_error("lan9118: Unimplemented MAC register write: %d = 0x%x\n",
 906                  s->mac_cmd & 0xf, val);
 907     }
 908 }
 909
 910 static uint32_t do_mac_read(lan9118_state *s, int reg)
 911 {
 912     switch (reg) {
 913     case MAC_CR:
 914         return s->mac_cr;
 915     case MAC_ADDRH:
 916         return s->conf.macaddr.a[4] | (s->conf.macaddr.a[5] << 8);
 917     case MAC_ADDRL:
 918         return s->conf.macaddr.a[0] | (s->conf.macaddr.a[1] << 8)
 919                | (s->conf.macaddr.a[2] << 16) | (s->conf.macaddr.a[3] << 24);
 920     case MAC_HASHH:
 921         return s->mac_hashh;
 922         break;
 923     case MAC_HASHL:
 924         return s->mac_hashl;
 925         break;
 926     case MAC_MII_ACC:
 927         return s->mac_mii_acc;
 928     case MAC_MII_DATA:
 929         return s->mac_mii_data;
 930     case MAC_FLOW:
 931         return s->mac_flow;
 932     default:
 933         hw_error("lan9118: Unimplemented MAC register read: %d\n",
 934                  s->mac_cmd & 0xf);
 935     }
 936 }
 937
 938 static void lan9118_eeprom_cmd(lan9118_state *s, int cmd, int addr)
 939 {
 940     s->e2p_cmd = (s->e2p_cmd & 0x10) | (cmd << 28) | addr;
 941     switch (cmd) {
 942     case 0:
 943         s->e2p_data = s->eeprom[addr];
 944         DPRINTF("EEPROM Read %d = 0x%02x\n", addr, s->e2p_data);
 945         break;
 946     case 1:
 947         s->eeprom_writable = 0;
 948         DPRINTF("EEPROM Write Disable\n");
 949         break;
 950     case 2: /* EWEN */
 951         s->eeprom_writable = 1;
 952         DPRINTF("EEPROM Write Enable\n");
 953         break;
 954     case 3: /* WRITE */
 955         if (s->eeprom_writable) {
 956             s->eeprom[addr] &= s->e2p_data;
 957             DPRINTF("EEPROM Write %d = 0x%02x\n", addr, s->e2p_data);
 958         } else {
 959             DPRINTF("EEPROM Write %d (ignored)\n", addr);
 960         }
 961         break;
 962     case 4: /* WRAL */
 963         if (s->eeprom_writable) {
 964             for (addr = 0; addr < 128; addr++) {
 965                 s->eeprom[addr] &= s->e2p_data;
 966             }
 967             DPRINTF("EEPROM Write All 0x%02x\n", s->e2p_data);
 968         } else {
 969             DPRINTF("EEPROM Write All (ignored)\n");
 970         }
 971         break;
 972     case 5: /* ERASE */
 973         if (s->eeprom_writable) {
 974             s->eeprom[addr] = 0xff;
 975             DPRINTF("EEPROM Erase %d\n", addr);
 976         } else {
 977             DPRINTF("EEPROM Erase %d (ignored)\n", addr);
 978         }
 979         break;
 980     case 6: /* ERAL */
 981         if (s->eeprom_writable) {
 982             memset(s->eeprom, 0xff, 128);
 983             DPRINTF("EEPROM Erase All\n");
 984         } else {
 985             DPRINTF("EEPROM Erase All (ignored)\n");
 986         }
 987         break;
 988     case 7: /* RELOAD */
 989         lan9118_reload_eeprom(s);
 990         break;
 991     }
 992 }
 993
 994 static void lan9118_tick(void *opaque)
 995 {
 996     lan9118_state *s = (lan9118_state *)opaque;
 997     if (s->int_en & GPT_INT) {
 998         s->int_sts |= GPT_INT;
 999     }
1000     lan9118_update(s);
1001 }
1002
1003 static void lan9118_writel(void *opaque, target_phys_addr_t offset,
1004                            uint64_t val, unsigned size)
1005 {
1006     lan9118_state *s = (lan9118_state *)opaque;
1007     offset &= 0xff;
1008
1009     //DPRINTF("Write reg 0x%02x = 0x%08x\n", (int)offset, val);
1010     if (offset >= 0x20 && offset < 0x40) {
1011         /* TX FIFO */
1012         tx_fifo_push(s, val);
1013         return;
1014     }
1015     switch (offset) {
1016     case CSR_IRQ_CFG:
1017         /* TODO: Implement interrupt deassertion intervals.  */
1018         val &= (IRQ_EN | IRQ_POL | IRQ_TYPE);
1019         s->irq_cfg = (s->irq_cfg & IRQ_INT) | val;
1020         break;
1021     case CSR_INT_STS:
1022         s->int_sts &= ~val;
1023         break;
1024     case CSR_INT_EN:
1025         s->int_en = val & ~RESERVED_INT;
1026         s->int_sts |= val & SW_INT;
1027         break;
1028     case CSR_FIFO_INT:
1029         DPRINTF("FIFO INT levels %08x\n", val);
1030         s->fifo_int = val;
1031         break;
1032     case CSR_RX_CFG:
1033         if (val & 0x8000) {
1034             /* RX_DUMP */
1035             s->rx_fifo_used = 0;
1036             s->rx_status_fifo_used = 0;
1037             s->rx_packet_size_tail = s->rx_packet_size_head;
1038             s->rx_packet_size[s->rx_packet_size_head] = 0;
1039         }
1040         s->rx_cfg = val & 0xcfff1ff0;
1041         break;
1042     case CSR_TX_CFG:
1043         if (val & 0x8000) {
1044             s->tx_status_fifo_used = 0;
1045         }
1046         if (val & 0x4000) {
1047             s->txp->state = TX_IDLE;
1048             s->txp->fifo_used = 0;
1049             s->txp->cmd_a = 0xffffffff;
1050         }
1051         s->tx_cfg = val & 6;
1052         break;
1053     case CSR_HW_CFG:
1054         if (val & 1) {
1055             /* SRST */
1056             lan9118_reset(&s->busdev.qdev);
1057         } else {
1058             s->hw_cfg = (val & 0x003f300) | (s->hw_cfg & 0x4);
1059         }
1060         break;
1061     case CSR_RX_DP_CTRL:
1062         if (val & 0x80000000) {
1063             /* Skip forward to next packet.  */
1064             s->rxp_pad = 0;
1065             s->rxp_offset = 0;
1066             if (s->rxp_size == 0) {
1067                 /* Pop a word to start the next packet.  */
1068                 rx_fifo_pop(s);
1069                 s->rxp_pad = 0;
1070                 s->rxp_offset = 0;
1071             }
1072             s->rx_fifo_head += s->rxp_size;
1073             if (s->rx_fifo_head >= s->rx_fifo_size) {
1074                 s->rx_fifo_head -= s->rx_fifo_size;
1075             }
1076         }
1077         break;
1078     case CSR_PMT_CTRL:
1079         if (val & 0x400) {
1080             phy_reset(s);
1081         }
1082         s->pmt_ctrl &= ~0x34e;
1083         s->pmt_ctrl |= (val & 0x34e);
1084         break;
1085     case CSR_GPIO_CFG:
1086         /* Probably just enabling LEDs.  */
1087         s->gpio_cfg = val & 0x7777071f;
1088         break;
1089     case CSR_GPT_CFG:
1090         if ((s->gpt_cfg ^ val) & GPT_TIMER_EN) {
1091             if (val & GPT_TIMER_EN) {
1092                 ptimer_set_count(s->timer, val & 0xffff);
1093                 ptimer_run(s->timer, 0);
1094             } else {
1095                 ptimer_stop(s->timer);
1096                 ptimer_set_count(s->timer, 0xffff);
1097             }
1098         }
1099         s->gpt_cfg = val & (GPT_TIMER_EN | 0xffff);
1100         break;
1101     case CSR_WORD_SWAP:
1102         /* Ignored because we're in 32-bit mode.  */
1103         s->word_swap = val;
1104         break;
1105     case CSR_MAC_CSR_CMD:
1106         s->mac_cmd = val & 0x4000000f;
1107         if (val & 0x80000000) {
1108             if (val & 0x40000000) {
1109                 s->mac_data = do_mac_read(s, val & 0xf);
1110                 DPRINTF("MAC read %d = 0x%08x\n", val & 0xf, s->mac_data);
1111             } else {
1112                 DPRINTF("MAC write %d = 0x%08x\n", val & 0xf, s->mac_data);
1113                 do_mac_write(s, val & 0xf, s->mac_data);
1114             }
1115         }
1116         break;
1117     case CSR_MAC_CSR_DATA:
1118         s->mac_data = val;
1119         break;
1120     case CSR_AFC_CFG:
1121         s->afc_cfg = val & 0x00ffffff;
1122         break;
1123     case CSR_E2P_CMD:
1124         lan9118_eeprom_cmd(s, (val >> 28) & 7, val & 0x7f);
1125         break;
1126     case CSR_E2P_DATA:
1127         s->e2p_data = val & 0xff;
1128         break;
1129
1130     default:
1131         hw_error("lan9118_write: Bad reg 0x%x = %x\n", (int)offset, (int)val);
1132         break;
1133     }
1134     lan9118_update(s);
1135 }
1136
1137 static void lan9118_writew(void *opaque, target_phys_addr_t offset,
1138                            uint32_t val)
1139 {
1140     lan9118_state *s = (lan9118_state *)opaque;
1141     offset &= 0xff;
1142
1143     if (s->write_word_prev_offset != (offset & ~0x3)) {
1144         /* New offset, reset word counter */
1145         s->write_word_n = 0;
1146         s->write_word_prev_offset = offset & ~0x3;
1147     }
1148
1149     if (offset & 0x2) {
1150         s->write_word_h = val;
1151     } else {
1152         s->write_word_l = val;
1153     }
1154
1155     //DPRINTF("Writew reg 0x%02x = 0x%08x\n", (int)offset, val);
1156     s->write_word_n++;
1157     if (s->write_word_n == 2) {
1158         s->write_word_n = 0;
1159         lan9118_writel(s, offset & ~3, s->write_word_l +
1160                 (s->write_word_h << 16), 4);
1161     }
1162 }
1163
1164 static void lan9118_16bit_mode_write(void *opaque, target_phys_addr_t offset,
1165                                      uint64_t val, unsigned size)
1166 {
1167     switch (size) {
1168     case 2:
1169         lan9118_writew(opaque, offset, (uint32_t)val);
1170         return;
1171     case 4:
1172         lan9118_writel(opaque, offset, val, size);
1173         return;
1174     }
1175
1176     hw_error("lan9118_write: Bad size 0x%x\n", size);
1177 }
1178
1179 static uint64_t lan9118_readl(void *opaque, target_phys_addr_t offset,
1180                               unsigned size)
1181 {
1182     lan9118_state *s = (lan9118_state *)opaque;
1183
1184     //DPRINTF("Read reg 0x%02x\n", (int)offset);
1185     if (offset < 0x20) {
1186         /* RX FIFO */
1187         return rx_fifo_pop(s);
1188     }
1189     switch (offset) {
1190     case 0x40:
1191         return rx_status_fifo_pop(s);
1192     case 0x44:
1193         return s->rx_status_fifo[s->tx_status_fifo_head];
1194     case 0x48:
1195         return tx_status_fifo_pop(s);
1196     case 0x4c:
1197         return s->tx_status_fifo[s->tx_status_fifo_head];
1198     case CSR_ID_REV:
1199         return 0x01180001;
1200     case CSR_IRQ_CFG:
1201         return s->irq_cfg;
1202     case CSR_INT_STS:
1203         return s->int_sts;
1204     case CSR_INT_EN:
1205         return s->int_en;
1206     case CSR_BYTE_TEST:
1207         return 0x87654321;
1208     case CSR_FIFO_INT:
1209         return s->fifo_int;
1210     case CSR_RX_CFG:
1211         return s->rx_cfg;
1212     case CSR_TX_CFG:
1213         return s->tx_cfg;
1214     case CSR_HW_CFG:
1215         return s->hw_cfg;
1216     case CSR_RX_DP_CTRL:
1217         return 0;
1218     case CSR_RX_FIFO_INF:
1219         return (s->rx_status_fifo_used << 16) | (s->rx_fifo_used << 2);
1220     case CSR_TX_FIFO_INF:
1221         return (s->tx_status_fifo_used << 16)
1222                | (s->tx_fifo_size - s->txp->fifo_used);
1223     case CSR_PMT_CTRL:
1224         return s->pmt_ctrl;
1225     case CSR_GPIO_CFG:
1226         return s->gpio_cfg;
1227     case CSR_GPT_CFG:
1228         return s->gpt_cfg;
1229     case CSR_GPT_CNT:
1230         return ptimer_get_count(s->timer);
1231     case CSR_WORD_SWAP:
1232         return s->word_swap;
1233     case CSR_FREE_RUN:
1234         return (qemu_get_clock_ns(vm_clock) / 40) - s->free_timer_start;
1235     case CSR_RX_DROP:
1236         /* TODO: Implement dropped frames counter.  */
1237         return 0;
1238     case CSR_MAC_CSR_CMD:
1239         return s->mac_cmd;
1240     case CSR_MAC_CSR_DATA:
1241         return s->mac_data;
1242     case CSR_AFC_CFG:
1243         return s->afc_cfg;
1244     case CSR_E2P_CMD:
1245         return s->e2p_cmd;
1246     case CSR_E2P_DATA:
1247         return s->e2p_data;
1248     }
1249     hw_error("lan9118_read: Bad reg 0x%x\n", (int)offset);
1250     return 0;
1251 }
1252
1253 static uint32_t lan9118_readw(void *opaque, target_phys_addr_t offset)
1254 {
1255     lan9118_state *s = (lan9118_state *)opaque;
1256     uint32_t val;
1257
1258     if (s->read_word_prev_offset != (offset & ~0x3)) {
1259         /* New offset, reset word counter */
1260         s->read_word_n = 0;
1261         s->read_word_prev_offset = offset & ~0x3;
1262     }
1263
1264     s->read_word_n++;
1265     if (s->read_word_n == 1) {
1266         s->read_long = lan9118_readl(s, offset & ~3, 4);
1267     } else {
1268         s->read_word_n = 0;
1269     }
1270
1271     if (offset & 2) {
1272         val = s->read_long >> 16;
1273     } else {
1274         val = s->read_long & 0xFFFF;
1275     }
1276
1277     //DPRINTF("Readw reg 0x%02x, val 0x%x\n", (int)offset, val);
1278     return val;
1279 }
1280
1281 static uint64_t lan9118_16bit_mode_read(void *opaque, target_phys_addr_t offset,
1282                                         unsigned size)
1283 {
1284     switch (size) {
1285     case 2:
1286         return lan9118_readw(opaque, offset);
1287     case 4:
1288         return lan9118_readl(opaque, offset, size);
1289     }
1290
1291     hw_error("lan9118_read: Bad size 0x%x\n", size);
1292     return 0;
1293 }
1294
1295 static const MemoryRegionOps lan9118_mem_ops = {
1296     .read = lan9118_readl,
1297     .write = lan9118_writel,
1298     .endianness = DEVICE_NATIVE_ENDIAN,
1299 };
1300
1301 static const MemoryRegionOps lan9118_16bit_mem_ops = {
1302     .read = lan9118_16bit_mode_read,
1303     .write = lan9118_16bit_mode_write,
1304     .endianness = DEVICE_NATIVE_ENDIAN,
1305 };
1306
1307 static void lan9118_cleanup(NetClientState *nc)
1308 {
1309     lan9118_state *s = DO_UPCAST(NICState, nc, nc)->opaque;
1310
1311     s->nic = NULL;
1312 }
1313
1314 static NetClientInfo net_lan9118_info = {
1315     .type = NET_CLIENT_OPTIONS_KIND_NIC,
1316     .size = sizeof(NICState),
1317     .can_receive = lan9118_can_receive,
1318     .receive = lan9118_receive,
1319     .cleanup = lan9118_cleanup,
1320     .link_status_changed = lan9118_set_link,
1321 };
1322
1323 static int lan9118_init1(SysBusDevice *dev)
1324 {
1325     lan9118_state *s = FROM_SYSBUS(lan9118_state, dev);
1326     QEMUBH *bh;
1327     int i;
1328     const MemoryRegionOps *mem_ops =
1329             s->mode_16bit ? &lan9118_16bit_mem_ops : &lan9118_mem_ops;
1330
1331     memory_region_init_io(&s->mmio, mem_ops, s, "lan9118-mmio", 0x100);
1332     sysbus_init_mmio(dev, &s->mmio);
1333     sysbus_init_irq(dev, &s->irq);
1334     qemu_macaddr_default_if_unset(&s->conf.macaddr);
1335
1336     s->nic = qemu_new_nic(&net_lan9118_info, &s->conf,
1337                           object_get_typename(OBJECT(dev)), dev->qdev.id, s);
1338     qemu_format_nic_info_str(&s->nic->nc, s->conf.macaddr.a);
1339     s->eeprom[0] = 0xa5;
1340     for (i = 0; i < 6; i++) {
1341         s->eeprom[i + 1] = s->conf.macaddr.a[i];
1342     }
1343     s->pmt_ctrl = 1;
1344     s->txp = &s->tx_packet;
1345
1346     bh = qemu_bh_new(lan9118_tick, s);
1347     s->timer = ptimer_init(bh);
1348     ptimer_set_freq(s->timer, 10000);
1349     ptimer_set_limit(s->timer, 0xffff, 1);
1350
1351     return 0;
1352 }
1353
1354 static Property lan9118_properties[] = {
1355     DEFINE_NIC_PROPERTIES(lan9118_state, conf),
1356     DEFINE_PROP_UINT32("mode_16bit", lan9118_state, mode_16bit, 0),
1357     DEFINE_PROP_END_OF_LIST(),
1358 };
1359
1360 static void lan9118_class_init(ObjectClass *klass, void *data)
1361 {
1362     DeviceClass *dc = DEVICE_CLASS(klass);
1363     SysBusDeviceClass *k = SYS_BUS_DEVICE_CLASS(klass);
1364
1365     k->init = lan9118_init1;
1366     dc->reset = lan9118_reset;
1367     dc->props = lan9118_properties;
1368     dc->vmsd = &vmstate_lan9118;
1369 }
1370
1371 static TypeInfo lan9118_info = {
1372     .name          = "lan9118",
1373     .parent        = TYPE_SYS_BUS_DEVICE,
1374     .instance_size = sizeof(lan9118_state),
1375     .class_init    = lan9118_class_init,
1376 };
1377
1378 static void lan9118_register_types(void)
1379 {
1380     type_register_static(&lan9118_info);
1381 }
1382
1383 /* Legacy helper function.  Should go away when machine config files are
1384    implemented.  */
1385 void lan9118_init(NICInfo *nd, uint32_t base, qemu_irq irq)
1386 {
1387     DeviceState *dev;
1388     SysBusDevice *s;
1389
1390     qemu_check_nic_model(nd, "lan9118");
1391     dev = qdev_create(NULL, "lan9118");
1392     qdev_set_nic_properties(dev, nd);
1393     qdev_init_nofail(dev);
1394     s = sysbus_from_qdev(dev);
1395     sysbus_mmio_map(s, 0, base);
1396     sysbus_connect_irq(s, 0, irq);
1397 }
1398
1399 type_init(lan9118_register_types)