src/jtag/drivers/bcm2835gpio.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2
   3 /***************************************************************************
   4  *   Copyright (C) 2013 by Paul Fertser, fercerpav@gmail.com               *
   5  *                                                                         *
   6  *   Copyright (C) 2012 by Creative Product Design, marc @ cpdesign.com.au *
   7  *   Based on at91rm9200.c (c) Anders Larsen                               *
   8  *   and RPi GPIO examples by Gert van Loo & Dom                           *
   9  ***************************************************************************/
  10
  11 #ifdef HAVE_CONFIG_H
  12 #include "config.h"
  13 #endif
  14
  15 #include <jtag/adapter.h>
  16 #include <jtag/interface.h>
  17 #include <transport/transport.h>
  18 #include "bitbang.h"
  19
  20 #include <sys/mman.h>
  21
  22 static char *bcm2835_peri_mem_dev;
  23 static off_t bcm2835_peri_base = 0x20000000;
  24 #define BCM2835_GPIO_BASE       (bcm2835_peri_base + 0x200000) /* GPIO controller */
  25
  26 #define BCM2835_PADS_GPIO_0_27          (bcm2835_peri_base + 0x100000)
  27 #define BCM2835_PADS_GPIO_0_27_OFFSET   (0x2c / 4)
  28
  29 /* See "GPIO Function Select Registers (GPFSELn)" in "Broadcom BCM2835 ARM Peripherals" datasheet. */
  30 #define BCM2835_GPIO_MODE_INPUT 0
  31 #define BCM2835_GPIO_MODE_OUTPUT 1
  32
  33 /* GPIO setup macros */
  34 #define MODE_GPIO(g) (*(pio_base+((g)/10))>>(((g)%10)*3) & 7)
  35 #define INP_GPIO(g) do { *(pio_base+((g)/10)) &= ~(7<<(((g)%10)*3)); } while (0)
  36 #define SET_MODE_GPIO(g, m) do { /* clear the mode bits first, then set as necessary */ \
  37                 INP_GPIO(g);                                            \
  38                 *(pio_base+((g)/10)) |=  ((m)<<(((g)%10)*3)); } while (0)
  39 #define OUT_GPIO(g) SET_MODE_GPIO(g, BCM2835_GPIO_MODE_OUTPUT)
  40
  41 #define GPIO_SET (*(pio_base+7))  /* sets   bits which are 1, ignores bits which are 0 */
  42 #define GPIO_CLR (*(pio_base+10)) /* clears bits which are 1, ignores bits which are 0 */
  43 #define GPIO_LEV (*(pio_base+13)) /* current level of the pin */
  44
  45 static int dev_mem_fd;
  46 static volatile uint32_t *pio_base = MAP_FAILED;
  47 static volatile uint32_t *pads_base = MAP_FAILED;
  48
  49 /* Transition delay coefficients */
  50 static int speed_coeff = 113714;
  51 static int speed_offset = 28;
  52 static unsigned int jtag_delay;
  53
  54 static const struct adapter_gpio_config *adapter_gpio_config;
  55 static struct initial_gpio_state {
  56         unsigned int mode;
  57         unsigned int output_level;
  58 } initial_gpio_state[ADAPTER_GPIO_IDX_NUM];
  59 static uint32_t initial_drive_strength_etc;
  60
  61 static inline const char *bcm2835_get_mem_dev(void)
  62 {
  63         if (bcm2835_peri_mem_dev)
  64                 return bcm2835_peri_mem_dev;
  65
  66         return "/dev/gpiomem";
  67 }
  68
  69 static inline void bcm2835_gpio_synchronize(void)
  70 {
  71         /* Ensure that previous writes to GPIO registers are flushed out of
  72          * the inner shareable domain to prevent pipelined writes to the
  73          * same address being merged.
  74          */
  75         __sync_synchronize();
  76 }
  77
  78 static inline void bcm2835_delay(void)
  79 {
  80         for (unsigned int i = 0; i < jtag_delay; i++)
  81                 asm volatile ("");
  82 }
  83
  84 static bool is_gpio_config_valid(enum adapter_gpio_config_index idx)
  85 {
  86         /* Only chip 0 is supported, accept unset value (-1) too */
  87         return adapter_gpio_config[idx].gpio_num <= 31;
  88 }
  89
  90 static void set_gpio_value(const struct adapter_gpio_config *gpio_config, int value)
  91 {
  92         value = value ^ (gpio_config->active_low ? 1 : 0);
  93         switch (gpio_config->drive) {
  94         case ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL:
  95                 if (value)
  96                         GPIO_SET = 1 << gpio_config->gpio_num;
  97                 else
  98                         GPIO_CLR = 1 << gpio_config->gpio_num;
  99                 /* For performance reasons assume the GPIO is already set as an output
 100                  * and therefore the call can be omitted here.
 101                  */
 102                 break;
 103         case ADAPTER_GPIO_DRIVE_MODE_OPEN_DRAIN:
 104                 if (value) {
 105                         INP_GPIO(gpio_config->gpio_num);
 106                 } else {
 107                         GPIO_CLR = 1 << gpio_config->gpio_num;
 108                         OUT_GPIO(gpio_config->gpio_num);
 109                 }
 110                 break;
 111         case ADAPTER_GPIO_DRIVE_MODE_OPEN_SOURCE:
 112                 if (value) {
 113                         GPIO_SET = 1 << gpio_config->gpio_num;
 114                         OUT_GPIO(gpio_config->gpio_num);
 115                 } else {
 116                         INP_GPIO(gpio_config->gpio_num);
 117                 }
 118                 break;
 119         }
 120         bcm2835_gpio_synchronize();
 121 }
 122
 123 static void restore_gpio(enum adapter_gpio_config_index idx)
 124 {
 125         if (is_gpio_config_valid(idx)) {
 126                 SET_MODE_GPIO(adapter_gpio_config[idx].gpio_num, initial_gpio_state[idx].mode);
 127                 if (initial_gpio_state[idx].mode == BCM2835_GPIO_MODE_OUTPUT) {
 128                         if (initial_gpio_state[idx].output_level)
 129                                 GPIO_SET = 1 << adapter_gpio_config[idx].gpio_num;
 130                         else
 131                                 GPIO_CLR = 1 << adapter_gpio_config[idx].gpio_num;
 132                 }
 133         }
 134         bcm2835_gpio_synchronize();
 135 }
 136
 137 static void initialize_gpio(enum adapter_gpio_config_index idx)
 138 {
 139         if (!is_gpio_config_valid(idx))
 140                 return;
 141
 142         initial_gpio_state[idx].mode = MODE_GPIO(adapter_gpio_config[idx].gpio_num);
 143         unsigned int shift = adapter_gpio_config[idx].gpio_num;
 144         initial_gpio_state[idx].output_level = (GPIO_LEV >> shift) & 1;
 145         LOG_DEBUG("saved GPIO mode for %s (GPIO %d %d): %d",
 146                         adapter_gpio_get_name(idx), adapter_gpio_config[idx].chip_num, adapter_gpio_config[idx].gpio_num,
 147                         initial_gpio_state[idx].mode);
 148
 149         if (adapter_gpio_config[idx].pull != ADAPTER_GPIO_PULL_NONE) {
 150                 LOG_WARNING("BCM2835 GPIO does not support pull-up or pull-down settings (signal %s)",
 151                         adapter_gpio_get_name(idx));
 152         }
 153
 154         switch (adapter_gpio_config[idx].init_state) {
 155         case ADAPTER_GPIO_INIT_STATE_INACTIVE:
 156                 set_gpio_value(&adapter_gpio_config[idx], 0);
 157                 break;
 158         case ADAPTER_GPIO_INIT_STATE_ACTIVE:
 159                 set_gpio_value(&adapter_gpio_config[idx], 1);
 160                 break;
 161         case ADAPTER_GPIO_INIT_STATE_INPUT:
 162                 INP_GPIO(adapter_gpio_config[idx].gpio_num);
 163                 break;
 164         }
 165
 166         /* Direction for non push-pull is already set by set_gpio_value() */
 167         if (adapter_gpio_config[idx].drive == ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL
 168                 && adapter_gpio_config[idx].init_state != ADAPTER_GPIO_INIT_STATE_INPUT)
 169                 OUT_GPIO(adapter_gpio_config[idx].gpio_num);
 170         bcm2835_gpio_synchronize();
 171 }
 172
 173 static bb_value_t bcm2835gpio_read(void)
 174 {
 175         unsigned int shift = adapter_gpio_config[ADAPTER_GPIO_IDX_TDO].gpio_num;
 176         uint32_t value = (GPIO_LEV >> shift) & 1;
 177         return value ^ (adapter_gpio_config[ADAPTER_GPIO_IDX_TDO].active_low ? BB_HIGH : BB_LOW);
 178
 179 }
 180
 181 static int bcm2835gpio_write(int tck, int tms, int tdi)
 182 {
 183         uint32_t set = tck << adapter_gpio_config[ADAPTER_GPIO_IDX_TCK].gpio_num |
 184                         tms << adapter_gpio_config[ADAPTER_GPIO_IDX_TMS].gpio_num |
 185                         tdi << adapter_gpio_config[ADAPTER_GPIO_IDX_TDI].gpio_num;
 186         uint32_t clear = !tck << adapter_gpio_config[ADAPTER_GPIO_IDX_TCK].gpio_num |
 187                         !tms << adapter_gpio_config[ADAPTER_GPIO_IDX_TMS].gpio_num |
 188                         !tdi << adapter_gpio_config[ADAPTER_GPIO_IDX_TDI].gpio_num;
 189
 190         GPIO_SET = set;
 191         GPIO_CLR = clear;
 192         bcm2835_gpio_synchronize();
 193
 194         bcm2835_delay();
 195
 196         return ERROR_OK;
 197 }
 198
 199 /* Requires push-pull drive mode for swclk and swdio */
 200 static int bcm2835gpio_swd_write_fast(int swclk, int swdio)
 201 {
 202         swclk = swclk ^ (adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK].active_low ? 1 : 0);
 203         swdio = swdio ^ (adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].active_low ? 1 : 0);
 204
 205         uint32_t set = swclk << adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK].gpio_num |
 206                                         swdio << adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num;
 207         uint32_t clear = !swclk << adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK].gpio_num |
 208                                         !swdio << adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num;
 209
 210         GPIO_SET = set;
 211         GPIO_CLR = clear;
 212         bcm2835_gpio_synchronize();
 213
 214         bcm2835_delay();
 215
 216         return ERROR_OK;
 217 }
 218
 219 /* Generic mode that works for open-drain/open-source drive modes, but slower */
 220 static int bcm2835gpio_swd_write_generic(int swclk, int swdio)
 221 {
 222         set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO], swdio);
 223         set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK], swclk); /* Write clock last */
 224
 225         bcm2835_delay();
 226
 227         return ERROR_OK;
 228 }
 229
 230 /* (1) assert or (0) deassert reset lines */
 231 static int bcm2835gpio_reset(int trst, int srst)
 232 {
 233         /* As the "adapter reset_config" command keeps the srst and trst gpio drive
 234          * mode settings in sync we can use our standard set_gpio_value() function
 235          * that honours drive mode and active low.
 236          */
 237         if (is_gpio_config_valid(ADAPTER_GPIO_IDX_SRST))
 238                 set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SRST], srst);
 239
 240         if (is_gpio_config_valid(ADAPTER_GPIO_IDX_TRST))
 241                 set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_TRST], trst);
 242
 243         LOG_DEBUG("trst %d gpio: %d %d, srst %d gpio: %d %d",
 244                 trst,
 245                 (int)adapter_gpio_config[ADAPTER_GPIO_IDX_TRST].chip_num,
 246                 (int)adapter_gpio_config[ADAPTER_GPIO_IDX_TRST].gpio_num,
 247                 srst,
 248                 (int)adapter_gpio_config[ADAPTER_GPIO_IDX_SRST].chip_num,
 249                 (int)adapter_gpio_config[ADAPTER_GPIO_IDX_SRST].gpio_num);
 250         return ERROR_OK;
 251 }
 252
 253 static void bcm2835_swdio_drive(bool is_output)
 254 {
 255         if (is_output) {
 256                 if (is_gpio_config_valid(ADAPTER_GPIO_IDX_SWDIO_DIR))
 257                         set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO_DIR], 1);
 258                 OUT_GPIO(adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num);
 259         } else {
 260                 INP_GPIO(adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num);
 261                 if (is_gpio_config_valid(ADAPTER_GPIO_IDX_SWDIO_DIR))
 262                         set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO_DIR], 0);
 263         }
 264         bcm2835_gpio_synchronize();
 265 }
 266
 267 static int bcm2835_swdio_read(void)
 268 {
 269         unsigned int shift = adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num;
 270         uint32_t value = (GPIO_LEV >> shift) & 1;
 271         return value ^ (adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].active_low ? 1 : 0);
 272 }
 273
 274 static int bcm2835gpio_khz(int khz, int *jtag_speed)
 275 {
 276         if (!khz) {
 277                 LOG_DEBUG("BCM2835 GPIO: RCLK not supported");
 278                 return ERROR_FAIL;
 279         }
 280         *jtag_speed = DIV_ROUND_UP(speed_coeff, khz) - speed_offset;
 281         LOG_DEBUG("jtag_delay %d", *jtag_speed);
 282         if (*jtag_speed < 0)
 283                 *jtag_speed = 0;
 284         return ERROR_OK;
 285 }
 286
 287 static int bcm2835gpio_speed_div(int speed, int *khz)
 288 {
 289         int divisor = speed + speed_offset;
 290         /* divide with roundig to the closest */
 291         *khz = (speed_coeff + divisor / 2) / divisor;
 292         return ERROR_OK;
 293 }
 294
 295 static int bcm2835gpio_speed(int speed)
 296 {
 297         jtag_delay = speed;
 298         return ERROR_OK;
 299 }
 300
 301 COMMAND_HANDLER(bcm2835gpio_handle_speed_coeffs)
 302 {
 303         if (CMD_ARGC == 2) {
 304                 COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], speed_coeff);
 305                 COMMAND_PARSE_NUMBER(int, CMD_ARGV[1], speed_offset);
 306         }
 307
 308         command_print(CMD, "BCM2835 GPIO: speed_coeffs = %d, speed_offset = %d",
 309                                   speed_coeff, speed_offset);
 310         return ERROR_OK;
 311 }
 312
 313 COMMAND_HANDLER(bcm2835gpio_handle_peripheral_mem_dev)
 314 {
 315         if (CMD_ARGC == 1) {
 316                 free(bcm2835_peri_mem_dev);
 317                 bcm2835_peri_mem_dev = strdup(CMD_ARGV[0]);
 318         }
 319
 320         command_print(CMD, "BCM2835 GPIO: peripheral_mem_dev = %s",
 321                                   bcm2835_get_mem_dev());
 322         return ERROR_OK;
 323 }
 324
 325 COMMAND_HANDLER(bcm2835gpio_handle_peripheral_base)
 326 {
 327         uint64_t tmp_base;
 328         if (CMD_ARGC == 1) {
 329                 COMMAND_PARSE_NUMBER(u64, CMD_ARGV[0], tmp_base);
 330                 bcm2835_peri_base = (off_t)tmp_base;
 331         }
 332
 333         tmp_base = bcm2835_peri_base;
 334         command_print(CMD, "BCM2835 GPIO: peripheral_base = 0x%08" PRIx64,
 335                                   tmp_base);
 336         return ERROR_OK;
 337 }
 338
 339 static const struct command_registration bcm2835gpio_subcommand_handlers[] = {
 340         {
 341                 .name = "speed_coeffs",
 342                 .handler = &bcm2835gpio_handle_speed_coeffs,
 343                 .mode = COMMAND_CONFIG,
 344                 .help = "SPEED_COEFF and SPEED_OFFSET for delay calculations.",
 345                 .usage = "[SPEED_COEFF SPEED_OFFSET]",
 346         },
 347         {
 348                 .name = "peripheral_mem_dev",
 349                 .handler = &bcm2835gpio_handle_peripheral_mem_dev,
 350                 .mode = COMMAND_CONFIG,
 351                 .help = "device to map memory mapped GPIOs from.",
 352                 .usage = "[device]",
 353         },
 354         {
 355                 .name = "peripheral_base",
 356                 .handler = &bcm2835gpio_handle_peripheral_base,
 357                 .mode = COMMAND_CONFIG,
 358                 .help = "peripheral base to access GPIOs, not needed with /dev/gpiomem.",
 359                 .usage = "[base]",
 360         },
 361
 362         COMMAND_REGISTRATION_DONE
 363 };
 364
 365 static const struct command_registration bcm2835gpio_command_handlers[] = {
 366         {
 367                 .name = "bcm2835gpio",
 368                 .mode = COMMAND_ANY,
 369                 .help = "perform bcm2835gpio management",
 370                 .chain = bcm2835gpio_subcommand_handlers,
 371                 .usage = "",
 372         },
 373         COMMAND_REGISTRATION_DONE
 374 };
 375
 376 static bool bcm2835gpio_jtag_mode_possible(void)
 377 {
 378         if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_TCK))
 379                 return false;
 380         if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_TMS))
 381                 return false;
 382         if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_TDI))
 383                 return false;
 384         if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_TDO))
 385                 return false;
 386         return true;
 387 }
 388
 389 static bool bcm2835gpio_swd_mode_possible(void)
 390 {
 391         if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_SWCLK))
 392                 return false;
 393         if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_SWDIO))
 394                 return false;
 395         return true;
 396 }
 397
 398 static void bcm2835gpio_munmap(void)
 399 {
 400         if (pio_base != MAP_FAILED) {
 401                 munmap((void *)pio_base, sysconf(_SC_PAGE_SIZE));
 402                 pio_base = MAP_FAILED;
 403         }
 404
 405         if (pads_base != MAP_FAILED) {
 406                 munmap((void *)pads_base, sysconf(_SC_PAGE_SIZE));
 407                 pads_base = MAP_FAILED;
 408         }
 409 }
 410
 411 static int bcm2835gpio_blink(int on)
 412 {
 413         if (is_gpio_config_valid(ADAPTER_GPIO_IDX_LED))
 414                 set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_LED], on);
 415
 416         return ERROR_OK;
 417 }
 418
 419 static struct bitbang_interface bcm2835gpio_bitbang = {
 420         .read = bcm2835gpio_read,
 421         .write = bcm2835gpio_write,
 422         .swdio_read = bcm2835_swdio_read,
 423         .swdio_drive = bcm2835_swdio_drive,
 424         .swd_write = bcm2835gpio_swd_write_generic,
 425         .blink = bcm2835gpio_blink,
 426 };
 427
 428 static int bcm2835gpio_init(void)
 429 {
 430         LOG_INFO("BCM2835 GPIO JTAG/SWD bitbang driver");
 431
 432         bitbang_interface = &bcm2835gpio_bitbang;
 433         adapter_gpio_config = adapter_gpio_get_config();
 434
 435         if (transport_is_jtag() && !bcm2835gpio_jtag_mode_possible()) {
 436                 LOG_ERROR("Require tck, tms, tdi and tdo gpios for JTAG mode");
 437                 return ERROR_JTAG_INIT_FAILED;
 438         }
 439
 440         if (transport_is_swd() && !bcm2835gpio_swd_mode_possible()) {
 441                 LOG_ERROR("Require swclk and swdio gpio for SWD mode");
 442                 return ERROR_JTAG_INIT_FAILED;
 443         }
 444
 445         bool is_gpiomem = strcmp(bcm2835_get_mem_dev(), "/dev/gpiomem") == 0;
 446         bool pad_mapping_possible = !is_gpiomem;
 447
 448         dev_mem_fd = open(bcm2835_get_mem_dev(), O_RDWR | O_SYNC);
 449         if (dev_mem_fd < 0) {
 450                 LOG_ERROR("open %s: %s", bcm2835_get_mem_dev(), strerror(errno));
 451                 /* TODO: add /dev/mem specific doc and refer to it
 452                  * if (!is_gpiomem && (errno == EACCES || errno == EPERM))
 453                  *      LOG_INFO("Consult the user's guide chapter 4.? how to set permissions and capabilities");
 454                  */
 455                 return ERROR_JTAG_INIT_FAILED;
 456         }
 457
 458         pio_base = mmap(NULL, sysconf(_SC_PAGE_SIZE), PROT_READ | PROT_WRITE,
 459                                 MAP_SHARED, dev_mem_fd, BCM2835_GPIO_BASE);
 460
 461         if (pio_base == MAP_FAILED) {
 462                 LOG_ERROR("mmap: %s", strerror(errno));
 463                 close(dev_mem_fd);
 464                 return ERROR_JTAG_INIT_FAILED;
 465         }
 466
 467         /* TODO: move pads config to a separate utility */
 468         if (pad_mapping_possible) {
 469                 pads_base = mmap(NULL, sysconf(_SC_PAGE_SIZE), PROT_READ | PROT_WRITE,
 470                                 MAP_SHARED, dev_mem_fd, BCM2835_PADS_GPIO_0_27);
 471
 472                 if (pads_base == MAP_FAILED) {
 473                         LOG_ERROR("mmap pads: %s", strerror(errno));
 474                         LOG_WARNING("Continuing with unchanged GPIO pad settings (drive strength and slew rate)");
 475                 }
 476         } else {
 477                 pads_base = MAP_FAILED;
 478         }
 479
 480         close(dev_mem_fd);
 481
 482         if (pads_base != MAP_FAILED) {
 483                 /* set 4mA drive strength, slew rate limited, hysteresis on */
 484                 initial_drive_strength_etc = pads_base[BCM2835_PADS_GPIO_0_27_OFFSET] & 0x1f;
 485 LOG_INFO("initial pads conf %08x", pads_base[BCM2835_PADS_GPIO_0_27_OFFSET]);
 486                 pads_base[BCM2835_PADS_GPIO_0_27_OFFSET] = 0x5a000008 + 1;
 487 LOG_INFO("pads conf set to %08x", pads_base[BCM2835_PADS_GPIO_0_27_OFFSET]);
 488         }
 489
 490         /* Configure JTAG/SWD signals. Default directions and initial states are handled
 491          * by adapter.c and "adapter gpio" command.
 492          */
 493         if (transport_is_jtag()) {
 494                 initialize_gpio(ADAPTER_GPIO_IDX_TDO);
 495                 initialize_gpio(ADAPTER_GPIO_IDX_TDI);
 496                 initialize_gpio(ADAPTER_GPIO_IDX_TMS);
 497                 initialize_gpio(ADAPTER_GPIO_IDX_TCK);
 498                 initialize_gpio(ADAPTER_GPIO_IDX_TRST);
 499         }
 500
 501         if (transport_is_swd()) {
 502                 /* swdio and its buffer should be initialized in the order that prevents
 503                  * two outputs from being connected together. This will occur if the
 504                  * swdio GPIO of the AM335x is configured as an output while its
 505                  * external buffer is configured to send the swdio signal from the
 506                  * target to the AM335x.
 507                  */
 508                 if (adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].init_state == ADAPTER_GPIO_INIT_STATE_INPUT) {
 509                         initialize_gpio(ADAPTER_GPIO_IDX_SWDIO);
 510                         initialize_gpio(ADAPTER_GPIO_IDX_SWDIO_DIR);
 511                 } else {
 512                         initialize_gpio(ADAPTER_GPIO_IDX_SWDIO_DIR);
 513                         initialize_gpio(ADAPTER_GPIO_IDX_SWDIO);
 514                 }
 515
 516                 initialize_gpio(ADAPTER_GPIO_IDX_SWCLK);
 517
 518                 if (adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK].drive == ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL &&
 519                                 adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].drive == ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL) {
 520                         LOG_DEBUG("BCM2835 GPIO using fast mode for SWD write");
 521                         bcm2835gpio_bitbang.swd_write = bcm2835gpio_swd_write_fast;
 522                 } else {
 523                         LOG_DEBUG("BCM2835 GPIO using generic mode for SWD write");
 524                         bcm2835gpio_bitbang.swd_write = bcm2835gpio_swd_write_generic;
 525                 }
 526         }
 527
 528         initialize_gpio(ADAPTER_GPIO_IDX_SRST);
 529         initialize_gpio(ADAPTER_GPIO_IDX_LED);
 530
 531         return ERROR_OK;
 532 }
 533
 534 static int bcm2835gpio_quit(void)
 535 {
 536         if (transport_is_jtag()) {
 537                 restore_gpio(ADAPTER_GPIO_IDX_TDO);
 538                 restore_gpio(ADAPTER_GPIO_IDX_TDI);
 539                 restore_gpio(ADAPTER_GPIO_IDX_TCK);
 540                 restore_gpio(ADAPTER_GPIO_IDX_TMS);
 541                 restore_gpio(ADAPTER_GPIO_IDX_TRST);
 542         }
 543
 544         if (transport_is_swd()) {
 545                 /* Restore swdio/swdio_dir to their initial modes, even if that means
 546                  * connecting two outputs. Begin by making swdio an input so that the
 547                  * current and final states of swdio and swdio_dir do not have to be
 548                  * considered to calculate the safe restoration order.
 549                  */
 550                 INP_GPIO(adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num);
 551                 restore_gpio(ADAPTER_GPIO_IDX_SWDIO_DIR);
 552                 restore_gpio(ADAPTER_GPIO_IDX_SWDIO);
 553                 restore_gpio(ADAPTER_GPIO_IDX_SWCLK);
 554         }
 555
 556         restore_gpio(ADAPTER_GPIO_IDX_SRST);
 557         restore_gpio(ADAPTER_GPIO_IDX_LED);
 558
 559         if (pads_base != MAP_FAILED) {
 560                 /* Restore drive strength. MSB is password ("5A") */
 561                 pads_base[BCM2835_PADS_GPIO_0_27_OFFSET] = 0x5A000000 | initial_drive_strength_etc;
 562         }
 563         bcm2835gpio_munmap();
 564         free(bcm2835_peri_mem_dev);
 565
 566         return ERROR_OK;
 567 }
 568
 569
 570 static const char * const bcm2835_transports[] = { "jtag", "swd", NULL };
 571
 572 static struct jtag_interface bcm2835gpio_interface = {
 573         .supported = DEBUG_CAP_TMS_SEQ,
 574         .execute_queue = bitbang_execute_queue,
 575 };
 576 struct adapter_driver bcm2835gpio_adapter_driver = {
 577         .name = "bcm2835gpio",
 578         .transports = bcm2835_transports,
 579         .commands = bcm2835gpio_command_handlers,
 580
 581         .init = bcm2835gpio_init,
 582         .quit = bcm2835gpio_quit,
 583         .reset = bcm2835gpio_reset,
 584         .speed = bcm2835gpio_speed,
 585         .khz = bcm2835gpio_khz,
 586         .speed_div = bcm2835gpio_speed_div,
 587
 588         .jtag_ops = &bcm2835gpio_interface,
 589         .swd_ops = &bitbang_swd,
 590 };