drivers/spi/omap_uwire.c

   1 /*
   2  * omap_uwire.c -- MicroWire interface driver for OMAP
   3  *
   4  * Copyright 2003 MontaVista Software Inc. <source@mvista.com>
   5  *
   6  * Ported to 2.6 OMAP uwire interface.
   7  * Copyright (C) 2004 Texas Instruments.
   8  *
   9  * Generalization patches by Juha Yrjola <juha.yrjola@nokia.com>
  10  *
  11  * Copyright (C) 2005 David Brownell (ported to 2.6 SPI interface)
  12  * Copyright (C) 2006 Nokia
  13  *
  14  * Many updates by Imre Deak <imre.deak@nokia.com>
  15  *
  16  * This program is free software; you can redistribute it and/or modify it
  17  * under the terms of the GNU General Public License as published by the
  18  * Free Software Foundation; either version 2 of the License, or (at your
  19  * option) any later version.
  20  *
  21  * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
  22  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
  23  * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
  24  * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
  25  * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
  26  * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
  27  * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
  28  * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
  29  * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
  30  * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  31  *
  32  * You should have received a copy of the GNU General Public License along
  33  * with this program; if not, write to the Free Software Foundation, Inc.,
  34  * 675 Mass Ave, Cambridge, MA 02139, USA.
  35  */
  36 #include <linux/kernel.h>
  37 #include <linux/init.h>
  38 #include <linux/delay.h>
  39 #include <linux/platform_device.h>
  40 #include <linux/workqueue.h>
  41 #include <linux/interrupt.h>
  42 #include <linux/err.h>
  43 #include <linux/clk.h>
  44
  45 #include <linux/spi/spi.h>
  46 #include <linux/spi/spi_bitbang.h>
  47
  48 #include <asm/system.h>
  49 #include <asm/irq.h>
  50 #include <asm/hardware.h>
  51 #include <asm/io.h>
  52 #include <asm/mach-types.h>
  53
  54 #include <asm/arch/mux.h>
  55 #include <asm/arch/omap730.h>   /* OMAP730_IO_CONF registers */
  56
  57
  58 /* FIXME address is now a platform device resource,
  59  * and irqs should show there too...
  60  */
  61 #define UWIRE_BASE_PHYS         0xFFFB3000
  62 #define UWIRE_BASE              ((void *__iomem)IO_ADDRESS(UWIRE_BASE_PHYS))
  63
  64 /* uWire Registers: */
  65 #define UWIRE_IO_SIZE 0x20
  66 #define UWIRE_TDR     0x00
  67 #define UWIRE_RDR     0x00
  68 #define UWIRE_CSR     0x01
  69 #define UWIRE_SR1     0x02
  70 #define UWIRE_SR2     0x03
  71 #define UWIRE_SR3     0x04
  72 #define UWIRE_SR4     0x05
  73 #define UWIRE_SR5     0x06
  74
  75 /* CSR bits */
  76 #define RDRB    (1 << 15)
  77 #define CSRB    (1 << 14)
  78 #define START   (1 << 13)
  79 #define CS_CMD  (1 << 12)
  80
  81 /* SR1 or SR2 bits */
  82 #define UWIRE_READ_FALLING_EDGE         0x0001
  83 #define UWIRE_READ_RISING_EDGE          0x0000
  84 #define UWIRE_WRITE_FALLING_EDGE        0x0000
  85 #define UWIRE_WRITE_RISING_EDGE         0x0002
  86 #define UWIRE_CS_ACTIVE_LOW             0x0000
  87 #define UWIRE_CS_ACTIVE_HIGH            0x0004
  88 #define UWIRE_FREQ_DIV_2                0x0000
  89 #define UWIRE_FREQ_DIV_4                0x0008
  90 #define UWIRE_FREQ_DIV_8                0x0010
  91 #define UWIRE_CHK_READY                 0x0020
  92 #define UWIRE_CLK_INVERTED              0x0040
  93
  94
  95 struct uwire_spi {
  96         struct spi_bitbang      bitbang;
  97         struct clk              *ck;
  98 };
  99
 100 struct uwire_state {
 101         unsigned        bits_per_word;
 102         unsigned        div1_idx;
 103 };
 104
 105 /* REVISIT compile time constant for idx_shift? */
 106 static unsigned int uwire_idx_shift;
 107
 108 static inline void uwire_write_reg(int idx, u16 val)
 109 {
 110         __raw_writew(val, UWIRE_BASE + (idx << uwire_idx_shift));
 111 }
 112
 113 static inline u16 uwire_read_reg(int idx)
 114 {
 115         return __raw_readw(UWIRE_BASE + (idx << uwire_idx_shift));
 116 }
 117
 118 static inline void omap_uwire_configure_mode(u8 cs, unsigned long flags)
 119 {
 120         u16     w, val = 0;
 121         int     shift, reg;
 122
 123         if (flags & UWIRE_CLK_INVERTED)
 124                 val ^= 0x03;
 125         val = flags & 0x3f;
 126         if (cs & 1)
 127                 shift = 6;
 128         else
 129                 shift = 0;
 130         if (cs <= 1)
 131                 reg = UWIRE_SR1;
 132         else
 133                 reg = UWIRE_SR2;
 134
 135         w = uwire_read_reg(reg);
 136         w &= ~(0x3f << shift);
 137         w |= val << shift;
 138         uwire_write_reg(reg, w);
 139 }
 140
 141 static int wait_uwire_csr_flag(u16 mask, u16 val, int might_not_catch)
 142 {
 143         u16 w;
 144         int c = 0;
 145         unsigned long max_jiffies = jiffies + HZ;
 146
 147         for (;;) {
 148                 w = uwire_read_reg(UWIRE_CSR);
 149                 if ((w & mask) == val)
 150                         break;
 151                 if (time_after(jiffies, max_jiffies)) {
 152                         printk(KERN_ERR "%s: timeout. reg=%#06x "
 153                                         "mask=%#06x val=%#06x\n",
 154                                __FUNCTION__, w, mask, val);
 155                         return -1;
 156                 }
 157                 c++;
 158                 if (might_not_catch && c > 64)
 159                         break;
 160         }
 161         return 0;
 162 }
 163
 164 static void uwire_set_clk1_div(int div1_idx)
 165 {
 166         u16 w;
 167
 168         w = uwire_read_reg(UWIRE_SR3);
 169         w &= ~(0x03 << 1);
 170         w |= div1_idx << 1;
 171         uwire_write_reg(UWIRE_SR3, w);
 172 }
 173
 174 static void uwire_chipselect(struct spi_device *spi, int value)
 175 {
 176         struct  uwire_state *ust = spi->controller_state;
 177         u16     w;
 178         int     old_cs;
 179
 180
 181         BUG_ON(wait_uwire_csr_flag(CSRB, 0, 0));
 182
 183         w = uwire_read_reg(UWIRE_CSR);
 184         old_cs = (w >> 10) & 0x03;
 185         if (value == BITBANG_CS_INACTIVE || old_cs != spi->chip_select) {
 186                 /* Deselect this CS, or the previous CS */
 187                 w &= ~CS_CMD;
 188                 uwire_write_reg(UWIRE_CSR, w);
 189         }
 190         /* activate specfied chipselect */
 191         if (value == BITBANG_CS_ACTIVE) {
 192                 uwire_set_clk1_div(ust->div1_idx);
 193                 /* invert clock? */
 194                 if (spi->mode & SPI_CPOL)
 195                         uwire_write_reg(UWIRE_SR4, 1);
 196                 else
 197                         uwire_write_reg(UWIRE_SR4, 0);
 198
 199                 w = spi->chip_select << 10;
 200                 w |= CS_CMD;
 201                 uwire_write_reg(UWIRE_CSR, w);
 202         }
 203 }
 204
 205 static int uwire_txrx(struct spi_device *spi, struct spi_transfer *t)
 206 {
 207         struct uwire_state *ust = spi->controller_state;
 208         unsigned        len = t->len;
 209         unsigned        bits = ust->bits_per_word;
 210         unsigned        bytes;
 211         u16             val, w;
 212         int             status = 0;;
 213
 214         if (!t->tx_buf && !t->rx_buf)
 215                 return 0;
 216
 217         /* Microwire doesn't read and write concurrently */
 218         if (t->tx_buf && t->rx_buf)
 219                 return -EPERM;
 220
 221         w = spi->chip_select << 10;
 222         w |= CS_CMD;
 223
 224         if (t->tx_buf) {
 225                 const u8        *buf = t->tx_buf;
 226
 227                 /* NOTE:  DMA could be used for TX transfers */
 228
 229                 /* write one or two bytes at a time */
 230                 while (len >= 1) {
 231                         /* tx bit 15 is first sent; we byteswap multibyte words
 232                          * (msb-first) on the way out from memory.
 233                          */
 234                         val = *buf++;
 235                         if (bits > 8) {
 236                                 bytes = 2;
 237                                 val |= *buf++ << 8;
 238                         } else
 239                                 bytes = 1;
 240                         val <<= 16 - bits;
 241
 242 #ifdef  VERBOSE
 243                         pr_debug("%s: write-%d =%04x\n",
 244                                         spi->dev.bus_id, bits, val);
 245 #endif
 246                         if (wait_uwire_csr_flag(CSRB, 0, 0))
 247                                 goto eio;
 248
 249                         uwire_write_reg(UWIRE_TDR, val);
 250
 251                         /* start write */
 252                         val = START | w | (bits << 5);
 253
 254                         uwire_write_reg(UWIRE_CSR, val);
 255                         len -= bytes;
 256
 257                         /* Wait till write actually starts.
 258                          * This is needed with MPU clock 60+ MHz.
 259                          * REVISIT: we may not have time to catch it...
 260                          */
 261                         if (wait_uwire_csr_flag(CSRB, CSRB, 1))
 262                                 goto eio;
 263
 264                         status += bytes;
 265                 }
 266
 267                 /* REVISIT:  save this for later to get more i/o overlap */
 268                 if (wait_uwire_csr_flag(CSRB, 0, 0))
 269                         goto eio;
 270
 271         } else if (t->rx_buf) {
 272                 u8              *buf = t->rx_buf;
 273
 274                 /* read one or two bytes at a time */
 275                 while (len) {
 276                         if (bits > 8) {
 277                                 bytes = 2;
 278                         } else
 279                                 bytes = 1;
 280
 281                         /* start read */
 282                         val = START | w | (bits << 0);
 283                         uwire_write_reg(UWIRE_CSR, val);
 284                         len -= bytes;
 285
 286                         /* Wait till read actually starts */
 287                         (void) wait_uwire_csr_flag(CSRB, CSRB, 1);
 288
 289                         if (wait_uwire_csr_flag(RDRB | CSRB,
 290                                                 RDRB, 0))
 291                                 goto eio;
 292
 293                         /* rx bit 0 is last received; multibyte words will
 294                          * be properly byteswapped on the way to memory.
 295                          */
 296                         val = uwire_read_reg(UWIRE_RDR);
 297                         val &= (1 << bits) - 1;
 298                         *buf++ = (u8) val;
 299                         if (bytes == 2)
 300                                 *buf++ = val >> 8;
 301                         status += bytes;
 302 #ifdef  VERBOSE
 303                         pr_debug("%s: read-%d =%04x\n",
 304                                         spi->dev.bus_id, bits, val);
 305 #endif
 306
 307                 }
 308         }
 309         return status;
 310 eio:
 311         return -EIO;
 312 }
 313
 314 static int uwire_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
 315 {
 316         struct uwire_state      *ust = spi->controller_state;
 317         struct uwire_spi        *uwire;
 318         unsigned                flags = 0;
 319         unsigned                bits;
 320         unsigned                hz;
 321         unsigned long           rate;
 322         int                     div1_idx;
 323         int                     div1;
 324         int                     div2;
 325         int                     status;
 326
 327         uwire = spi_master_get_devdata(spi->master);
 328
 329         if (spi->chip_select > 3) {
 330                 pr_debug("%s: cs%d?\n", spi->dev.bus_id, spi->chip_select);
 331                 status = -ENODEV;
 332                 goto done;
 333         }
 334
 335         bits = spi->bits_per_word;
 336         if (t != NULL && t->bits_per_word)
 337                 bits = t->bits_per_word;
 338         if (!bits)
 339                 bits = 8;
 340
 341         if (bits > 16) {
 342                 pr_debug("%s: wordsize %d?\n", spi->dev.bus_id, bits);
 343                 status = -ENODEV;
 344                 goto done;
 345         }
 346         ust->bits_per_word = bits;
 347
 348         /* mode 0..3, clock inverted separately;
 349          * standard nCS signaling;
 350          * don't treat DI=high as "not ready"
 351          */
 352         if (spi->mode & SPI_CS_HIGH)
 353                 flags |= UWIRE_CS_ACTIVE_HIGH;
 354
 355         if (spi->mode & SPI_CPOL)
 356                 flags |= UWIRE_CLK_INVERTED;
 357
 358         switch (spi->mode & (SPI_CPOL | SPI_CPHA)) {
 359         case SPI_MODE_0:
 360         case SPI_MODE_3:
 361                 flags |= UWIRE_WRITE_FALLING_EDGE | UWIRE_READ_RISING_EDGE;
 362                 break;
 363         case SPI_MODE_1:
 364         case SPI_MODE_2:
 365                 flags |= UWIRE_WRITE_RISING_EDGE | UWIRE_READ_FALLING_EDGE;
 366                 break;
 367         }
 368
 369         /* assume it's already enabled */
 370         rate = clk_get_rate(uwire->ck);
 371
 372         hz = spi->max_speed_hz;
 373         if (t != NULL && t->speed_hz)
 374                 hz = t->speed_hz;
 375
 376         if (!hz) {
 377                 pr_debug("%s: zero speed?\n", spi->dev.bus_id);
 378                 status = -EINVAL;
 379                 goto done;
 380         }
 381
 382         /* F_INT = mpu_xor_clk / DIV1 */
 383         for (div1_idx = 0; div1_idx < 4; div1_idx++) {
 384                 switch (div1_idx) {
 385                 case 0:
 386                         div1 = 2;
 387                         break;
 388                 case 1:
 389                         div1 = 4;
 390                         break;
 391                 case 2:
 392                         div1 = 7;
 393                         break;
 394                 default:
 395                 case 3:
 396                         div1 = 10;
 397                         break;
 398                 }
 399                 div2 = (rate / div1 + hz - 1) / hz;
 400                 if (div2 <= 8)
 401                         break;
 402         }
 403         if (div1_idx == 4) {
 404                 pr_debug("%s: lowest clock %ld, need %d\n",
 405                         spi->dev.bus_id, rate / 10 / 8, hz);
 406                 status = -EDOM;
 407                 goto done;
 408         }
 409
 410         /* we have to cache this and reset in uwire_chipselect as this is a
 411          * global parameter and another uwire device can change it under
 412          * us */
 413         ust->div1_idx = div1_idx;
 414         uwire_set_clk1_div(div1_idx);
 415
 416         rate /= div1;
 417
 418         switch (div2) {
 419         case 0:
 420         case 1:
 421         case 2:
 422                 flags |= UWIRE_FREQ_DIV_2;
 423                 rate /= 2;
 424                 break;
 425         case 3:
 426         case 4:
 427                 flags |= UWIRE_FREQ_DIV_4;
 428                 rate /= 4;
 429                 break;
 430         case 5:
 431         case 6:
 432         case 7:
 433         case 8:
 434                 flags |= UWIRE_FREQ_DIV_8;
 435                 rate /= 8;
 436                 break;
 437         }
 438         omap_uwire_configure_mode(spi->chip_select, flags);
 439         pr_debug("%s: uwire flags %02x, armxor %lu KHz, SCK %lu KHz\n",
 440                         __FUNCTION__, flags,
 441                         clk_get_rate(uwire->ck) / 1000,
 442                         rate / 1000);
 443         status = 0;
 444 done:
 445         return status;
 446 }
 447
 448 /* the spi->mode bits understood by this driver: */
 449 #define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH)
 450
 451 static int uwire_setup(struct spi_device *spi)
 452 {
 453         struct uwire_state *ust = spi->controller_state;
 454
 455         if (spi->mode & ~MODEBITS) {
 456                 dev_dbg(&spi->dev, "setup: unsupported mode bits %x\n",
 457                         spi->mode & ~MODEBITS);
 458                 return -EINVAL;
 459         }
 460
 461         if (ust == NULL) {
 462                 ust = kzalloc(sizeof(*ust), GFP_KERNEL);
 463                 if (ust == NULL)
 464                         return -ENOMEM;
 465                 spi->controller_state = ust;
 466         }
 467
 468         return uwire_setup_transfer(spi, NULL);
 469 }
 470
 471 static void uwire_cleanup(struct spi_device *spi)
 472 {
 473         kfree(spi->controller_state);
 474 }
 475
 476 static void uwire_off(struct uwire_spi *uwire)
 477 {
 478         uwire_write_reg(UWIRE_SR3, 0);
 479         clk_disable(uwire->ck);
 480         clk_put(uwire->ck);
 481         spi_master_put(uwire->bitbang.master);
 482 }
 483
 484 static int __init uwire_probe(struct platform_device *pdev)
 485 {
 486         struct spi_master       *master;
 487         struct uwire_spi        *uwire;
 488         int                     status;
 489
 490         master = spi_alloc_master(&pdev->dev, sizeof *uwire);
 491         if (!master)
 492                 return -ENODEV;
 493
 494         uwire = spi_master_get_devdata(master);
 495         dev_set_drvdata(&pdev->dev, uwire);
 496
 497         uwire->ck = clk_get(&pdev->dev, "armxor_ck");
 498         if (!uwire->ck || IS_ERR(uwire->ck)) {
 499                 dev_dbg(&pdev->dev, "no mpu_xor_clk ?\n");
 500                 spi_master_put(master);
 501                 return -ENODEV;
 502         }
 503         clk_enable(uwire->ck);
 504
 505         if (cpu_is_omap730())
 506                 uwire_idx_shift = 1;
 507         else
 508                 uwire_idx_shift = 2;
 509
 510         uwire_write_reg(UWIRE_SR3, 1);
 511
 512         master->bus_num = 2;    /* "official" */
 513         master->num_chipselect = 4;
 514         master->setup = uwire_setup;
 515         master->cleanup = uwire_cleanup;
 516
 517         uwire->bitbang.master = master;
 518         uwire->bitbang.chipselect = uwire_chipselect;
 519         uwire->bitbang.setup_transfer = uwire_setup_transfer;
 520         uwire->bitbang.txrx_bufs = uwire_txrx;
 521
 522         status = spi_bitbang_start(&uwire->bitbang);
 523         if (status < 0)
 524                 uwire_off(uwire);
 525         return status;
 526 }
 527
 528 static int __exit uwire_remove(struct platform_device *pdev)
 529 {
 530         struct uwire_spi        *uwire = dev_get_drvdata(&pdev->dev);
 531         int                     status;
 532
 533         // FIXME remove all child devices, somewhere ...
 534
 535         status = spi_bitbang_stop(&uwire->bitbang);
 536         uwire_off(uwire);
 537         return status;
 538 }
 539
 540 /* work with hotplug and coldplug */
 541 MODULE_ALIAS("platform:omap_uwire");
 542
 543 static struct platform_driver uwire_driver = {
 544         .driver = {
 545                 .name           = "omap_uwire",
 546                 .owner          = THIS_MODULE,
 547         },
 548         .remove         = __exit_p(uwire_remove),
 549         // suspend ... unuse ck
 550         // resume ... use ck
 551 };
 552
 553 static int __init omap_uwire_init(void)
 554 {
 555         /* FIXME move these into the relevant board init code. also, include
 556          * H3 support; it uses tsc2101 like H2 (on a different chipselect).
 557          */
 558
 559         if (machine_is_omap_h2()) {
 560                 /* defaults: W21 SDO, U18 SDI, V19 SCL */
 561                 omap_cfg_reg(N14_1610_UWIRE_CS0);
 562                 omap_cfg_reg(N15_1610_UWIRE_CS1);
 563         }
 564         if (machine_is_omap_perseus2()) {
 565                 /* configure pins: MPU_UW_nSCS1, MPU_UW_SDO, MPU_UW_SCLK */
 566                 int val = omap_readl(OMAP730_IO_CONF_9) & ~0x00EEE000;
 567                 omap_writel(val | 0x00AAA000, OMAP730_IO_CONF_9);
 568         }
 569
 570         return platform_driver_probe(&uwire_driver, uwire_probe);
 571 }
 572
 573 static void __exit omap_uwire_exit(void)
 574 {
 575         platform_driver_unregister(&uwire_driver);
 576 }
 577
 578 subsys_initcall(omap_uwire_init);
 579 module_exit(omap_uwire_exit);
 580
 581 MODULE_LICENSE("GPL");
 582