Committer: Michael Beasley <mike@snafu.setup>
[mikesnafu-overlay.git] / arch / ppc / platforms / 4xx / yucca.h
blobbc9684e66a84f0cb83366acb7ebef430109d5770
1 /*
2 * Yucca board definitions
4 * Roland Dreier <rolandd@cisco.com> (based on luan.h by Matt Porter)
6 * Copyright 2004-2005 MontaVista Software Inc.
7 * Copyright (c) 2005 Cisco Systems. All rights reserved.
9 * This program is free software; you can redistribute it and/or modify it
10 * under the terms of the GNU General Public License as published by the
11 * Free Software Foundation; either version 2 of the License, or (at your
12 * option) any later version.
16 #ifdef __KERNEL__
17 #ifndef __ASM_YUCCA_H__
18 #define __ASM_YUCCA_H__
20 #include <platforms/4xx/ppc440spe.h>
22 /* F/W TLB mapping used in bootloader glue to reset EMAC */
23 #define PPC44x_EMAC0_MR0 0xa0000800
25 /* Location of MAC addresses in PIBS image */
26 #define PIBS_FLASH_BASE 0xffe00000
27 #define PIBS_MAC_BASE (PIBS_FLASH_BASE+0x1b0400)
29 /* External timer clock frequency */
30 #define YUCCA_TMR_CLK 25000000
33 * FPGA registers
35 #define YUCCA_FPGA_REG_BASE 0x00000004e2000000ULL
36 #define YUCCA_FPGA_REG_SIZE 0x24
38 #define FPGA_REG1A 0x1a
40 #define FPGA_REG1A_PE0_GLED 0x8000
41 #define FPGA_REG1A_PE1_GLED 0x4000
42 #define FPGA_REG1A_PE2_GLED 0x2000
43 #define FPGA_REG1A_PE0_YLED 0x1000
44 #define FPGA_REG1A_PE1_YLED 0x0800
45 #define FPGA_REG1A_PE2_YLED 0x0400
46 #define FPGA_REG1A_PE0_PWRON 0x0200
47 #define FPGA_REG1A_PE1_PWRON 0x0100
48 #define FPGA_REG1A_PE2_PWRON 0x0080
49 #define FPGA_REG1A_PE0_REFCLK_ENABLE 0x0040
50 #define FPGA_REG1A_PE1_REFCLK_ENABLE 0x0020
51 #define FPGA_REG1A_PE2_REFCLK_ENABLE 0x0010
52 #define FPGA_REG1A_PE_SPREAD0 0x0008
53 #define FPGA_REG1A_PE_SPREAD1 0x0004
54 #define FPGA_REG1A_PE_SELSOURCE_0 0x0002
55 #define FPGA_REG1A_PE_SELSOURCE_1 0x0001
57 #define FPGA_REG1C 0x1c
59 #define FPGA_REG1C_PE0_ROOTPOINT 0x8000
60 #define FPGA_REG1C_PE1_ENDPOINT 0x4000
61 #define FPGA_REG1C_PE2_ENDPOINT 0x2000
62 #define FPGA_REG1C_PE0_PRSNT 0x1000
63 #define FPGA_REG1C_PE1_PRSNT 0x0800
64 #define FPGA_REG1C_PE2_PRSNT 0x0400
65 #define FPGA_REG1C_PE0_WAKE 0x0080
66 #define FPGA_REG1C_PE1_WAKE 0x0040
67 #define FPGA_REG1C_PE2_WAKE 0x0020
68 #define FPGA_REG1C_PE0_PERST 0x0010
69 #define FPGA_REG1C_PE1_PERST 0x0008
70 #define FPGA_REG1C_PE2_PERST 0x0004
73 * Serial port defines
75 #define RS_TABLE_SIZE 3
77 /* PIBS defined UART mappings, used before early_serial_setup */
78 #define UART0_IO_BASE 0xa0000200
79 #define UART1_IO_BASE 0xa0000300
80 #define UART2_IO_BASE 0xa0000600
82 #define BASE_BAUD 11059200
83 #define STD_UART_OP(num) \
84 { 0, BASE_BAUD, 0, UART##num##_INT, \
85 (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \
86 iomem_base: (void*)UART##num##_IO_BASE, \
87 io_type: SERIAL_IO_MEM},
89 #define SERIAL_PORT_DFNS \
90 STD_UART_OP(0) \
91 STD_UART_OP(1) \
92 STD_UART_OP(2)
94 /* PCI support */
95 #define YUCCA_PCIX_LOWER_IO 0x00000000
96 #define YUCCA_PCIX_UPPER_IO 0x0000ffff
97 #define YUCCA_PCIX_LOWER_MEM 0x80000000
98 #define YUCCA_PCIX_UPPER_MEM 0x8fffffff
99 #define YUCCA_PCIE_LOWER_MEM 0x90000000
100 #define YUCCA_PCIE_MEM_SIZE 0x10000000
102 #define YUCCA_PCIX_MEM_SIZE 0x10000000
103 #define YUCCA_PCIX_MEM_OFFSET 0x00000000
104 #define YUCCA_PCIE_MEM_SIZE 0x10000000
105 #define YUCCA_PCIE_MEM_OFFSET 0x00000000
107 #endif /* __ASM_YUCCA_H__ */
108 #endif /* __KERNEL__ */