drivers/ide/ht6560b.c

   1 /*
   2  *  Copyright (C) 1995-2000  Linus Torvalds & author (see below)
   3  */
   4
   5 /*
   6  *  HT-6560B EIDE-controller support
   7  *  To activate controller support use kernel parameter "ide0=ht6560b".
   8  *  Use hdparm utility to enable PIO mode support.
   9  *
  10  *  Author:    Mikko Ala-Fossi            <maf@iki.fi>
  11  *             Jan Evert van Grootheest   <j.e.van.grootheest@caiway.nl>
  12  *
  13  *  Try:  http://www.maf.iki.fi/~maf/ht6560b/
  14  */
  15
  16 #define DRV_NAME        "ht6560b"
  17 #define HT6560B_VERSION "v0.08"
  18
  19 #include <linux/module.h>
  20 #include <linux/types.h>
  21 #include <linux/kernel.h>
  22 #include <linux/delay.h>
  23 #include <linux/timer.h>
  24 #include <linux/mm.h>
  25 #include <linux/ioport.h>
  26 #include <linux/blkdev.h>
  27 #include <linux/ide.h>
  28 #include <linux/init.h>
  29
  30 #include <asm/io.h>
  31
  32 /* #define DEBUG */  /* remove comments for DEBUG messages */
  33
  34 /*
  35  * The special i/o-port that HT-6560B uses to configuration:
  36  *    bit0 (0x01): "1" selects secondary interface
  37  *    bit2 (0x04): "1" enables FIFO function
  38  *    bit5 (0x20): "1" enables prefetched data read function  (???)
  39  *
  40  * The special i/o-port that HT-6560A uses to configuration:
  41  *    bit0 (0x01): "1" selects secondary interface
  42  *    bit1 (0x02): "1" enables prefetched data read function
  43  *    bit2 (0x04): "0" enables multi-master system            (?)
  44  *    bit3 (0x08): "1" 3 cycle time, "0" 2 cycle time         (?)
  45  */
  46 #define HT_CONFIG_PORT    0x3e6
  47 #define HT_CONFIG(drivea) (u8)(((drivea)->drive_data & 0xff00) >> 8)
  48 /*
  49  * FIFO + PREFETCH (both a/b-model)
  50  */
  51 #define HT_CONFIG_DEFAULT 0x1c /* no prefetch */
  52 /* #define HT_CONFIG_DEFAULT 0x3c */ /* with prefetch */
  53 #define HT_SECONDARY_IF   0x01
  54 #define HT_PREFETCH_MODE  0x20
  55
  56 /*
  57  * ht6560b Timing values:
  58  *
  59  * I reviewed some assembler source listings of htide drivers and found
  60  * out how they setup those cycle time interfacing values, as they at Holtek
  61  * call them. IDESETUP.COM that is supplied with the drivers figures out
  62  * optimal values and fetches those values to drivers. I found out that
  63  * they use Select register to fetch timings to the ide board right after
  64  * interface switching. After that it was quite easy to add code to
  65  * ht6560b.c.
  66  *
  67  * IDESETUP.COM gave me values 0x24, 0x45, 0xaa, 0xff that worked fine
  68  * for hda and hdc. But hdb needed higher values to work, so I guess
  69  * that sometimes it is necessary to give higher value than IDESETUP
  70  * gives.   [see cmd640.c for an extreme example of this. -ml]
  71  *
  72  * Perhaps I should explain something about these timing values:
  73  * The higher nibble of value is the Recovery Time  (rt) and the lower nibble
  74  * of the value is the Active Time  (at). Minimum value 2 is the fastest and
  75  * the maximum value 15 is the slowest. Default values should be 15 for both.
  76  * So 0x24 means 2 for rt and 4 for at. Each of the drives should have
  77  * both values, and IDESETUP gives automatically rt=15 st=15 for CDROMs or
  78  * similar. If value is too small there will be all sorts of failures.
  79  *
  80  * Timing byte consists of
  81  *      High nibble:  Recovery Cycle Time  (rt)
  82  *           The valid values range from 2 to 15. The default is 15.
  83  *
  84  *      Low nibble:   Active Cycle Time    (at)
  85  *           The valid values range from 2 to 15. The default is 15.
  86  *
  87  * You can obtain optimized timing values by running Holtek IDESETUP.COM
  88  * for DOS. DOS drivers get their timing values from command line, where
  89  * the first value is the Recovery Time and the second value is the
  90  * Active Time for each drive. Smaller value gives higher speed.
  91  * In case of failures you should probably fall back to a higher value.
  92  */
  93 #define HT_TIMING(drivea) (u8)((drivea)->drive_data & 0x00ff)
  94 #define HT_TIMING_DEFAULT 0xff
  95
  96 /*
  97  * This routine handles interface switching for the peculiar hardware design
  98  * on the F.G.I./Holtek HT-6560B VLB IDE interface.
  99  * The HT-6560B can only enable one IDE port at a time, and requires a
 100  * silly sequence (below) whenever we switch between primary and secondary.
 101  */
 102
 103 /*
 104  * This routine is invoked from ide.c to prepare for access to a given drive.
 105  */
 106 static void ht6560b_dev_select(ide_drive_t *drive)
 107 {
 108         ide_hwif_t *hwif = drive->hwif;
 109         unsigned long flags;
 110         static u8 current_select = 0;
 111         static u8 current_timing = 0;
 112         u8 select, timing;
 113
 114         local_irq_save(flags);
 115
 116         select = HT_CONFIG(drive);
 117         timing = HT_TIMING(drive);
 118
 119         /*
 120          * Need to enforce prefetch sometimes because otherwise
 121          * it'll hang (hard).
 122          */
 123         if (drive->media != ide_disk ||
 124             (drive->dev_flags & IDE_DFLAG_PRESENT) == 0)
 125                 select |= HT_PREFETCH_MODE;
 126
 127         if (select != current_select || timing != current_timing) {
 128                 current_select = select;
 129                 current_timing = timing;
 130                 (void)inb(HT_CONFIG_PORT);
 131                 (void)inb(HT_CONFIG_PORT);
 132                 (void)inb(HT_CONFIG_PORT);
 133                 (void)inb(HT_CONFIG_PORT);
 134                 outb(select, HT_CONFIG_PORT);
 135                 /*
 136                  * Set timing for this drive:
 137                  */
 138                 outb(timing, hwif->io_ports.device_addr);
 139                 (void)inb(hwif->io_ports.status_addr);
 140 #ifdef DEBUG
 141                 printk("ht6560b: %s: select=%#x timing=%#x\n",
 142                         drive->name, select, timing);
 143 #endif
 144         }
 145         local_irq_restore(flags);
 146
 147         outb(drive->select | ATA_DEVICE_OBS, hwif->io_ports.device_addr);
 148 }
 149
 150 /*
 151  * Autodetection and initialization of ht6560b
 152  */
 153 static int __init try_to_init_ht6560b(void)
 154 {
 155         u8 orig_value;
 156         int i;
 157
 158         /* Autodetect ht6560b */
 159         if ((orig_value = inb(HT_CONFIG_PORT)) == 0xff)
 160                 return 0;
 161
 162         for (i=3;i>0;i--) {
 163                 outb(0x00, HT_CONFIG_PORT);
 164                 if (!( (~inb(HT_CONFIG_PORT)) & 0x3f )) {
 165                         outb(orig_value, HT_CONFIG_PORT);
 166                         return 0;
 167                 }
 168         }
 169         outb(0x00, HT_CONFIG_PORT);
 170         if ((~inb(HT_CONFIG_PORT))& 0x3f) {
 171                 outb(orig_value, HT_CONFIG_PORT);
 172                 return 0;
 173         }
 174         /*
 175          * Ht6560b autodetected
 176          */
 177         outb(HT_CONFIG_DEFAULT, HT_CONFIG_PORT);
 178         outb(HT_TIMING_DEFAULT, 0x1f6); /* Select register */
 179         (void)inb(0x1f7);               /* Status register */
 180
 181         printk("ht6560b " HT6560B_VERSION
 182                ": chipset detected and initialized"
 183 #ifdef DEBUG
 184                " with debug enabled"
 185 #endif
 186                "\n"
 187                 );
 188         return 1;
 189 }
 190
 191 static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
 192 {
 193         int active_time, recovery_time;
 194         int active_cycles, recovery_cycles;
 195         int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
 196
 197         if (pio) {
 198                 unsigned int cycle_time;
 199                 struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
 200
 201                 cycle_time = ide_pio_cycle_time(drive, pio);
 202
 203                 /*
 204                  *  Just like opti621.c we try to calculate the
 205                  *  actual cycle time for recovery and activity
 206                  *  according system bus speed.
 207                  */
 208                 active_time = t->active;
 209                 recovery_time = cycle_time - active_time - t->setup;
 210                 /*
 211                  *  Cycle times should be Vesa bus cycles
 212                  */
 213                 active_cycles   = (active_time   * bus_speed + 999) / 1000;
 214                 recovery_cycles = (recovery_time * bus_speed + 999) / 1000;
 215                 /*
 216                  *  Upper and lower limits
 217                  */
 218                 if (active_cycles   < 2)  active_cycles   = 2;
 219                 if (recovery_cycles < 2)  recovery_cycles = 2;
 220                 if (active_cycles   > 15) active_cycles   = 15;
 221                 if (recovery_cycles > 15) recovery_cycles = 0;  /* 0==16 */
 222
 223 #ifdef DEBUG
 224                 printk("ht6560b: drive %s setting pio=%d recovery=%d (%dns) active=%d (%dns)\n", drive->name, pio, recovery_cycles, recovery_time, active_cycles, active_time);
 225 #endif
 226
 227                 return (u8)((recovery_cycles << 4) | active_cycles);
 228         } else {
 229
 230 #ifdef DEBUG
 231                 printk("ht6560b: drive %s setting pio=0\n", drive->name);
 232 #endif
 233
 234                 return HT_TIMING_DEFAULT;    /* default setting */
 235         }
 236 }
 237
 238 static DEFINE_SPINLOCK(ht6560b_lock);
 239
 240 /*
 241  *  Enable/Disable so called prefetch mode
 242  */
 243 static void ht_set_prefetch(ide_drive_t *drive, u8 state)
 244 {
 245         unsigned long flags;
 246         int t = HT_PREFETCH_MODE << 8;
 247
 248         spin_lock_irqsave(&ht6560b_lock, flags);
 249
 250         /*
 251          *  Prefetch mode and unmask irq seems to conflict
 252          */
 253         if (state) {
 254                 drive->drive_data |= t;   /* enable prefetch mode */
 255                 drive->dev_flags |= IDE_DFLAG_NO_UNMASK;
 256                 drive->dev_flags &= ~IDE_DFLAG_UNMASK;
 257         } else {
 258                 drive->drive_data &= ~t;  /* disable prefetch mode */
 259                 drive->dev_flags &= ~IDE_DFLAG_NO_UNMASK;
 260         }
 261
 262         spin_unlock_irqrestore(&ht6560b_lock, flags);
 263
 264 #ifdef DEBUG
 265         printk("ht6560b: drive %s prefetch mode %sabled\n", drive->name, (state ? "en" : "dis"));
 266 #endif
 267 }
 268
 269 static void ht6560b_set_pio_mode(ide_drive_t *drive, const u8 pio)
 270 {
 271         unsigned long flags;
 272         u8 timing;
 273
 274         switch (pio) {
 275         case 8:         /* set prefetch off */
 276         case 9:         /* set prefetch on */
 277                 ht_set_prefetch(drive, pio & 1);
 278                 return;
 279         }
 280
 281         timing = ht_pio2timings(drive, pio);
 282
 283         spin_lock_irqsave(&ht6560b_lock, flags);
 284         drive->drive_data &= 0xff00;
 285         drive->drive_data |= timing;
 286         spin_unlock_irqrestore(&ht6560b_lock, flags);
 287
 288 #ifdef DEBUG
 289         printk("ht6560b: drive %s tuned to pio mode %#x timing=%#x\n", drive->name, pio, timing);
 290 #endif
 291 }
 292
 293 static void __init ht6560b_init_dev(ide_drive_t *drive)
 294 {
 295         ide_hwif_t *hwif = drive->hwif;
 296         /* Setting default configurations for drives. */
 297         int t = (HT_CONFIG_DEFAULT << 8) | HT_TIMING_DEFAULT;
 298
 299         if (hwif->channel)
 300                 t |= (HT_SECONDARY_IF << 8);
 301
 302         drive->drive_data = t;
 303 }
 304
 305 static int probe_ht6560b;
 306
 307 module_param_named(probe, probe_ht6560b, bool, 0);
 308 MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
 309
 310 static const struct ide_tp_ops ht6560b_tp_ops = {
 311         .exec_command           = ide_exec_command,
 312         .read_status            = ide_read_status,
 313         .read_altstatus         = ide_read_altstatus,
 314         .write_devctl           = ide_write_devctl,
 315
 316         .dev_select             = ht6560b_dev_select,
 317         .tf_load                = ide_tf_load,
 318         .tf_read                = ide_tf_read,
 319
 320         .input_data             = ide_input_data,
 321         .output_data            = ide_output_data,
 322 };
 323
 324 static const struct ide_port_ops ht6560b_port_ops = {
 325         .init_dev               = ht6560b_init_dev,
 326         .set_pio_mode           = ht6560b_set_pio_mode,
 327 };
 328
 329 static const struct ide_port_info ht6560b_port_info __initdata = {
 330         .name                   = DRV_NAME,
 331         .chipset                = ide_ht6560b,
 332         .tp_ops                 = &ht6560b_tp_ops,
 333         .port_ops               = &ht6560b_port_ops,
 334         .host_flags             = IDE_HFLAG_SERIALIZE | /* is this needed? */
 335                                   IDE_HFLAG_NO_DMA |
 336                                   IDE_HFLAG_ABUSE_PREFETCH,
 337         .pio_mask               = ATA_PIO4,
 338 };
 339
 340 static int __init ht6560b_init(void)
 341 {
 342         if (probe_ht6560b == 0)
 343                 return -ENODEV;
 344
 345         if (!request_region(HT_CONFIG_PORT, 1, DRV_NAME)) {
 346                 printk(KERN_NOTICE "%s: HT_CONFIG_PORT not found\n",
 347                         __func__);
 348                 return -ENODEV;
 349         }
 350
 351         if (!try_to_init_ht6560b()) {
 352                 printk(KERN_NOTICE "%s: HBA not found\n", __func__);
 353                 goto release_region;
 354         }
 355
 356         return ide_legacy_device_add(&ht6560b_port_info, 0);
 357
 358 release_region:
 359         release_region(HT_CONFIG_PORT, 1);
 360         return -ENODEV;
 361 }
 362
 363 module_init(ht6560b_init);
 364
 365 MODULE_AUTHOR("See Local File");
 366 MODULE_DESCRIPTION("HT-6560B EIDE-controller support");
 367 MODULE_LICENSE("GPL");