2 # Touchscreen driver configuration
4 menuconfig INPUT_TOUCHSCREEN
7 Say Y here, and a list of supported touchscreens will be displayed.
8 This option doesn't affect the kernel.
14 config TOUCHSCREEN_ADS7846
15 tristate "ADS7846/TSC2046 and ADS7843 based touchscreens"
17 depends on HWMON = n || HWMON
19 Say Y here if you have a touchscreen interface using the
20 ADS7846/TSC2046 or ADS7843 controller, and your board-specific
21 setup code includes that in its table of SPI devices.
23 If HWMON is selected, and the driver is told the reference voltage
24 on your board, you will also get hwmon interfaces for the voltage
25 (and on ads7846/tsc2046, temperature) sensors of this chip.
27 If unsure, say N (but it's safe to say "Y").
29 To compile this driver as a module, choose M here: the
30 module will be called ads7846.
32 config TOUCHSCREEN_BITSY
33 tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
34 depends on SA1100_BITSY
37 Say Y here if you have the h3600 (Bitsy) touchscreen.
41 To compile this driver as a module, choose M here: the
42 module will be called h3600_ts_input.
44 config TOUCHSCREEN_CORGI
45 tristate "SharpSL (Corgi and Spitz series) touchscreen driver"
46 depends on PXA_SHARPSL
49 Say Y here to enable the driver for the touchscreen on the
50 Sharp SL-C7xx and SL-Cxx00 series of PDAs.
54 To compile this driver as a module, choose M here: the
55 module will be called corgi_ts.
57 config TOUCHSCREEN_FUJITSU
58 tristate "Fujitsu serial touchscreen"
61 Say Y here if you have the Fujitsu touchscreen (such as one
62 installed in Lifebook P series laptop) connected to your
67 To compile this driver as a module, choose M here: the
68 module will be called fujitsu-ts.
70 config TOUCHSCREEN_GUNZE
71 tristate "Gunze AHL-51S touchscreen"
74 Say Y here if you have the Gunze AHL-51 touchscreen connected to
79 To compile this driver as a module, choose M here: the
80 module will be called gunze.
82 config TOUCHSCREEN_ELO
83 tristate "Elo serial touchscreens"
86 Say Y here if you have an Elo serial touchscreen connected to
91 To compile this driver as a module, choose M here: the
92 module will be called elo.
94 config TOUCHSCREEN_MTOUCH
95 tristate "MicroTouch serial touchscreens"
98 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
103 To compile this driver as a module, choose M here: the
104 module will be called mtouch.
106 config TOUCHSCREEN_MK712
107 tristate "ICS MicroClock MK712 touchscreen"
109 Say Y here if you have the ICS MicroClock MK712 touchscreen
110 controller chip in your system.
114 To compile this driver as a module, choose M here: the
115 module will be called mk712.
117 config TOUCHSCREEN_HP600
118 tristate "HP Jornada 6xx touchscreen"
119 depends on SH_HP6XX && SH_ADC
121 Say Y here if you have a HP Jornada 620/660/680/690 and want to
122 support the built-in touchscreen.
124 To compile this driver as a module, choose M here: the
125 module will be called hp680_ts_input.
127 config TOUCHSCREEN_HP7XX
128 tristate "HP Jornada 7xx touchscreen"
129 depends on SA1100_JORNADA720_SSP
131 Say Y here if you have a HP Jornada 710/720/728 and want
132 to support the built-in touchscreen.
134 To compile this driver as a module, choose M here: the
135 module will be called jornada720_ts.
137 config TOUCHSCREEN_PENMOUNT
138 tristate "Penmount serial touchscreen"
141 Say Y here if you have a Penmount serial touchscreen connected to
146 To compile this driver as a module, choose M here: the
147 module will be called penmount.
149 config TOUCHSCREEN_TOUCHRIGHT
150 tristate "Touchright serial touchscreen"
153 Say Y here if you have a Touchright serial touchscreen connected to
158 To compile this driver as a module, choose M here: the
159 module will be called touchright.
161 config TOUCHSCREEN_TOUCHWIN
162 tristate "Touchwin serial touchscreen"
165 Say Y here if you have a Touchwin serial touchscreen connected to
170 To compile this driver as a module, choose M here: the
171 module will be called touchwin.
173 config TOUCHSCREEN_UCB1400
174 tristate "Philips UCB1400 touchscreen"
177 This enables support for the Philips UCB1400 touchscreen interface.
178 The UCB1400 is an AC97 audio codec. The touchscreen interface
179 will be initialized only after the ALSA subsystem has been
180 brought up and the UCB1400 detected. You therefore have to
181 configure ALSA support as well (either built-in or modular,
182 independently of whether this driver is itself built-in or
183 modular) for this driver to work.
185 To compile this driver as a module, choose M here: the
186 module will be called ucb1400_ts.
188 config TOUCHSCREEN_WM97XX
189 tristate "Support for WM97xx AC97 touchscreen controllers"
192 Say Y here if you have a Wolfson Microelectronics WM97xx
193 touchscreen connected to your system. Note that this option
194 only enables core driver, you will also need to select
195 support for appropriate chip below.
199 To compile this driver as a module, choose M here: the
200 module will be called wm97xx-ts.
202 config TOUCHSCREEN_WM9705
203 bool "WM9705 Touchscreen interface support"
204 depends on TOUCHSCREEN_WM97XX
206 Say Y here if you have a Wolfson Microelectronics WM9705
207 touchscreen controller connected to your system.
211 config TOUCHSCREEN_WM9712
212 bool "WM9712 Touchscreen interface support"
213 depends on TOUCHSCREEN_WM97XX
215 Say Y here if you have a Wolfson Microelectronics WM9712
216 touchscreen controller connected to your system.
220 config TOUCHSCREEN_WM9713
221 bool "WM9713 Touchscreen interface support"
222 depends on TOUCHSCREEN_WM97XX
224 Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen
225 controller connected to your system.
229 config TOUCHSCREEN_USB_COMPOSITE
230 tristate "USB Touchscreen Driver"
231 depends on USB_ARCH_HAS_HCD
234 USB Touchscreen driver for:
235 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
236 - PanJit TouchSet USB
237 - 3M MicroTouch USB (EX II series)
239 - some other eTurboTouch
242 - IRTOUCHSYSTEMS/UNITOP
244 - GoTop Super_Q2/GogoPen/PenPower tablets
246 Have a look at <http://linux.chapter7.ch/touchkit/> for
247 a usage description and the required user-space stuff.
249 To compile this driver as a module, choose M here: the
250 module will be called usbtouchscreen.
252 config TOUCHSCREEN_USB_EGALAX
254 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
255 depends on TOUCHSCREEN_USB_COMPOSITE
257 config TOUCHSCREEN_USB_PANJIT
259 bool "PanJit device support" if EMBEDDED
260 depends on TOUCHSCREEN_USB_COMPOSITE
262 config TOUCHSCREEN_USB_3M
264 bool "3M/Microtouch EX II series device support" if EMBEDDED
265 depends on TOUCHSCREEN_USB_COMPOSITE
267 config TOUCHSCREEN_USB_ITM
269 bool "ITM device support" if EMBEDDED
270 depends on TOUCHSCREEN_USB_COMPOSITE
272 config TOUCHSCREEN_USB_ETURBO
274 bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
275 depends on TOUCHSCREEN_USB_COMPOSITE
277 config TOUCHSCREEN_USB_GUNZE
279 bool "Gunze AHL61 device support" if EMBEDDED
280 depends on TOUCHSCREEN_USB_COMPOSITE
282 config TOUCHSCREEN_USB_DMC_TSC10
284 bool "DMC TSC-10/25 device support" if EMBEDDED
285 depends on TOUCHSCREEN_USB_COMPOSITE
287 config TOUCHSCREEN_USB_IRTOUCH
289 bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
290 depends on TOUCHSCREEN_USB_COMPOSITE
292 config TOUCHSCREEN_USB_IDEALTEK
294 bool "IdealTEK URTC1000 device support" if EMBEDDED
295 depends on TOUCHSCREEN_USB_COMPOSITE
297 config TOUCHSCREEN_USB_GENERAL_TOUCH
299 bool "GeneralTouch Touchscreen device support" if EMBEDDED
300 depends on TOUCHSCREEN_USB_COMPOSITE
302 config TOUCHSCREEN_USB_GOTOP
304 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
305 depends on TOUCHSCREEN_USB_COMPOSITE