3 menu "TI OMAP Implementations"
9 prompt "OMAP System Type"
10 default ARCH_OMAP2PLUS
16 "Systems based on omap7xx, omap15xx or omap16xx"
22 "Systems based on omap24xx, omap34xx or omap44xx"
26 depends on ARCH_OMAP2PLUS
31 depends on ARCH_OMAP2PLUS
33 select USB_ARCH_HAS_EHCI
37 depends on ARCH_OMAP2PLUS
43 comment "OMAP Feature Selections"
45 config OMAP_DEBUG_DEVICES
48 For debug cards on TI reference boards.
50 config OMAP_DEBUG_LEDS
52 depends on OMAP_DEBUG_DEVICES
53 default y if LEDS || LEDS_OMAP_DEBUG
55 config OMAP_RESET_CLOCKS
56 bool "Reset unused clocks during boot"
59 Say Y if you want to reset unused clocks during boot.
60 This option saves power, but assumes all drivers are
61 using the clock framework. Broken drivers that do not
62 yet use clock framework may not work with this option.
63 If you are booting from another operating system, you
64 probably do not want this option enabled until your
65 device drivers work properly.
68 bool "OMAP multiplexing support"
72 Pin multiplexing support for OMAP boards. If your bootloader
73 sets the multiplexing correctly, say N. Otherwise, or if unsure,
77 bool "Multiplexing debug output"
80 Makes the multiplexing functions print out a lot of debug info.
81 This is useful if you want to find out the correct values of the
82 multiplexing registers.
84 config OMAP_MUX_WARNINGS
85 bool "Warn about pins the bootloader didn't set up"
89 Choose Y here to warn whenever driver initialization logic needs
90 to change the pin multiplexing setup. When there are no warnings
91 printed, it's safe to deselect OMAP_MUX for your product.
98 Say Y here if you want support for the OMAP Multichannel
102 tristate "Mailbox framework support"
105 Say Y here if you want to use OMAP Mailbox framework support for
106 DSP, IVA1.0 and IVA2 in OMAP1/2/3.
111 config OMAP_IOMMU_DEBUG
112 depends on OMAP_IOMMU
116 prompt "System timer"
117 default OMAP_MPU_TIMER
119 config OMAP_MPU_TIMER
122 Select this option if you want to use the OMAP mpu timer. This
123 timer provides more intra-tick resolution than the 32KHz timer,
124 but consumes more power.
126 config OMAP_32K_TIMER
127 bool "Use 32KHz timer"
128 depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
130 Select this option if you want to enable the OMAP 32KHz timer.
131 This timer saves power compared to the OMAP_MPU_TIMER, and has
132 support for no tick during idle. The 32KHz timer provides less
133 intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is
134 currently only available for OMAP16XX, 24XX, 34XX and OMAP4.
138 config OMAP_32K_TIMER_HZ
139 int "Kernel internal timer frequency for 32KHz timer"
141 depends on OMAP_32K_TIMER
144 Kernel internal timer frequency should be a divisor of 32768,
148 bool "Use dual-mode timer"
149 depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
151 Select this option if you want to use OMAP Dual-Mode timers.
153 config OMAP_SERIAL_WAKE
154 bool "Enable wake-up events for serial ports"
155 depends on ARCH_OMAP1 && OMAP_MUX
158 Select this option if you want to have your system wake up
159 to data on the serial RX line. This allows you to wake the
160 system from serial console.
163 prompt "OMAP PM layer selection"
171 bool "No-op/debug PM layer"