beceem: remove version ifdef's

[linux-2.6/x86.git] / drivers / staging / bcm / Macros.h

/*************************************
*       Macros.h
**************************************/
#ifndef __MACROS_H__
#define __MACROS_H__

#define TX_TIMER_PERIOD 10      //10 msec
#define MAX_CLASSIFIERS 100
//#define MAX_CLASSIFIERS_PER_SF  20
#define MAX_TARGET_DSX_BUFFERS 24

#define MAX_CNTRL_PKTS  100
#define MAX_DATA_PKTS           200
#define MAX_ETH_SIZE            1536
#define MAX_CNTL_PKT_SIZE 2048
/* TIMER RELATED */
#define JIFFIES_2_QUADPART()    (ULONG)(jiffies * 10000) // jiffies(1msec) to Quadpart(100nsec)

#define MTU_SIZE 1400

#define MAC_ADDR_REGISTER 0xbf60d000


///////////Quality of Service///////////////////////////
#define NO_OF_QUEUES                            17
#define HiPriority                  NO_OF_QUEUES-1
#define LowPriority                 0
#define BE                          2
#define rtPS                        4
#define ERTPS                       5
#define UGS                         6

#define BE_BUCKET_SIZE                  1024*1024*100  //32kb
#define rtPS_BUCKET_SIZE                1024*1024*100    //8kb
#define MAX_ALLOWED_RATE                1024*1024*100
#define TX_PACKET_THRESHOLD             10
#define XSECONDS                    1*HZ
#define DSC_ACTIVATE_REQUEST            248
#define QUEUE_DEPTH_OFFSET          0x1fc01000
#define MAX_DEVICE_DESC_SIZE            2040
#define MAX_CTRL_QUEUE_LEN                      100
#define MAX_APP_QUEUE_LEN                       200
#define MAX_LATENCY_ALLOWED                     0xFFFFFFFF
#define DEFAULT_UG_INTERVAL                     250
#define DEFAULT_UGI_FACTOR                      4

#define DEFAULT_PERSFCOUNT                      60
#define MAX_CONNECTIONS                         10
#define MAX_CLASS_NAME_LENGTH           32

#define ETH_LENGTH_OF_ADDRESS           6
#define MAX_MULTICAST_ADDRESSES     32
#define IP_LENGTH_OF_ADDRESS            4

#define IP_PACKET_ONLY_MODE                     0
#define ETH_PACKET_TUNNELING_MODE       1

////////////Link Request//////////////
#define SET_MAC_ADDRESS_REQUEST         0
#define SYNC_UP_REQUEST             1
#define SYNCED_UP                   2
#define LINK_UP_REQUEST             3
#define LINK_CONNECTED              4
#define SYNC_UP_NOTIFICATION            2
#define LINK_UP_NOTIFICATION            4


#define LINK_NET_ENTRY              0x0002
#define HMC_STATUS                                      0x0004
#define LINK_UP_CONTROL_REQ         0x83

#define STATS_POINTER_REQ_STATUS    0x86
#define NETWORK_ENTRY_REQ_PAYLOAD   198
#define LINK_DOWN_REQ_PAYLOAD           226
#define SYNC_UP_REQ_PAYLOAD         228
#define STATISTICS_POINTER_REQ          237
#define LINK_UP_REQ_PAYLOAD         245
#define LINK_UP_ACK                 246

#define STATS_MSG_SIZE              4
#define INDEX_TO_DATA               4

#define GO_TO_IDLE_MODE_PAYLOAD                 210
#define COME_UP_FROM_IDLE_MODE_PAYLOAD  211
#define IDLE_MODE_SF_UPDATE_MSG                 187

#define SKB_RESERVE_ETHERNET_HEADER     16
#define SKB_RESERVE_PHS_BYTES           32

#define IP_PACKET_ONLY_MODE                     0
#define ETH_PACKET_TUNNELING_MODE       1

#define ETH_CS_802_3                            1
#define ETH_CS_802_1Q_VLAN                      3
#define IPV4_CS                                         1
#define IPV6_CS                                         2
#define ETH_CS_MASK                                     0x3f

/** \brief Validity bit maps for TLVs in packet classification rule */

#define PKT_CLASSIFICATION_USER_PRIORITY_VALID          0
#define PKT_CLASSIFICATION_VLANID_VALID                         1

#ifndef MIN
#define MIN(_a, _b) ((_a) < (_b)? (_a): (_b))
#endif


/*Leader related terms */
#define LEADER_STATUS                                   0x00
#define LEADER_STATUS_TCP_ACK                   0x1
#define LEADER_SIZE                             sizeof(LEADER)
#define MAC_ADDR_REQ_SIZE                               sizeof(PACKETTOSEND)
#define SS_INFO_REQ_SIZE                                sizeof(PACKETTOSEND)
#define CM_REQUEST_SIZE                                 LEADER_SIZE + sizeof(stLocalSFChangeRequest)
#define IDLE_REQ_SIZE                                   sizeof(PACKETTOSEND)


#define MAX_TRANSFER_CTRL_BYTE_USB              2 * 1024

#define GET_MAILBOX1_REG_REQUEST        0x87
#define GET_MAILBOX1_REG_RESPONSE       0x67
#define VCID_CONTROL_PACKET             0x00

#define TRANSMIT_NETWORK_DATA           0x00
#define RECEIVED_NETWORK_DATA           0x20

#define CM_RESPONSES                                    0xA0
#define STATUS_RSP                                              0xA1
#define LINK_CONTROL_RESP                               0xA2
#define IDLE_MODE_STATUS                                0xA3
#define STATS_POINTER_RESP                              0xA6
#define MGMT_MSG_INFO_SW_STATUS         0xA7
#define AUTH_SS_HOST_MSG                        0xA8

#define CM_DSA_ACK_PAYLOAD                              247
#define CM_DSC_ACK_PAYLOAD                              248
#define CM_DSD_ACK_PAYLOAD                              249
#define CM_DSDEACTVATE                                  250
#define TOTAL_MASKED_ADDRESS_IN_BYTES   32

#define MAC_REQ                         0
#define LINK_RESP                       1
#define RSSI_INDICATION         2

#define SS_INFO                 4
#define STATISTICS_INFO         5
#define CM_INDICATION           6
#define PARAM_RESP                      7
#define BUFFER_1K                       1024
#define BUFFER_2K                       BUFFER_1K*2
#define BUFFER_4K                       BUFFER_2K*2
#define BUFFER_8K                       BUFFER_4K*2
#define BUFFER_16K                      BUFFER_8K*2
#define DOWNLINK_DIR 0
#define UPLINK_DIR 1

#define BCM_SIGNATURE           "BECEEM"


#define GPIO_OUTPUT_REGISTER     0x0F00003C
#define BCM_GPIO_OUTPUT_SET_REG  0x0F000040
#define BCM_GPIO_OUTPUT_CLR_REG  0x0F000044
#define GPIO_MODE_REGISTER       0x0F000034
#define GPIO_PIN_STATE_REGISTER  0x0F000038


typedef struct _LINK_STATE {
        UCHAR   ucLinkStatus;
    UCHAR   bIdleMode;
        UCHAR   bShutdownMode;
}LINK_STATE, *PLINK_STATE;


enum enLinkStatus {
    WAIT_FOR_SYNC =     1,
    PHY_SYNC_ACHIVED =  2,
    LINKUP_IN_PROGRESS = 3,
    LINKUP_DONE     =   4,
    DREG_RECIEVED =             5,
    LINK_STATUS_RESET_RECIEVED = 6,
    PERIODIC_WAKE_UP_NOTIFICATION_FRM_FW  = 7,
    LINK_SHUTDOWN_REQ_FROM_FIRMWARE = 8,
    COMPLETE_WAKE_UP_NOTIFICATION_FRM_FW =9
};

typedef enum _E_PHS_DSC_ACTION
{
        eAddPHSRule=0,
        eSetPHSRule,
        eDeletePHSRule,
        eDeleteAllPHSRules
}E_PHS_DSC_ACTION;


#define CM_CONTROL_NEWDSX_MULTICLASSIFIER_REQ           0x89    // Host to Mac
#define CM_CONTROL_NEWDSX_MULTICLASSIFIER_RESP      0xA9    // Mac to Host
#define MASK_DISABLE_HEADER_SUPPRESSION                         0x10 //0b000010000
#define MINIMUM_PENDING_DESCRIPTORS                                     5

#define SHUTDOWN_HOSTINITIATED_REQUESTPAYLOAD 0xCC
#define SHUTDOWN_ACK_FROM_DRIVER 0x1
#define SHUTDOWN_NACK_FROM_DRIVER 0x2

#define LINK_SYNC_UP_SUBTYPE            0x0001
#define LINK_SYNC_DOWN_SUBTYPE          0x0001



#define CONT_MODE 1
#define SINGLE_DESCRIPTOR 1


#define DESCRIPTOR_LENGTH 0x30
#define FIRMWARE_DESCS_ADDRESS 0x1F100000


#define CLOCK_RESET_CNTRL_REG_1 0x0F00000C
#define CLOCK_RESET_CNTRL_REG_2 0x0F000840



#define TX_DESCRIPTOR_HEAD_REGISTER 0x0F010034
#define RX_DESCRIPTOR_HEAD_REGISTER 0x0F010094

#define STATISTICS_BEGIN_ADDR        0xbf60f02c

#define MAX_PENDING_CTRL_PACKET (MAX_CTRL_QUEUE_LEN-10)

#define WIMAX_MAX_MTU                   (MTU_SIZE + ETH_HLEN)
#define AUTO_LINKUP_ENABLE              0x2
#define AUTO_SYNC_DISABLE               0x1
#define AUTO_FIRM_DOWNLOAD              0x1
#define SETTLE_DOWN_TIME                50

#define HOST_BUS_SUSPEND_BIT            16

#define IDLE_MESSAGE 0x81

#define MIPS_CLOCK_133MHz 1

#define TARGET_CAN_GO_TO_IDLE_MODE 2
#define TARGET_CAN_NOT_GO_TO_IDLE_MODE 3
#define IDLE_MODE_PAYLOAD_LENGTH 8

#define IP_HEADER(Buffer) ((IPHeaderFormat*)(Buffer))
#define IPV4                            4
#define IP_VERSION(byte)        (((byte&0xF0)>>4))

#define SET_MAC_ADDRESS  193
#define SET_MAC_ADDRESS_RESPONSE 236

#define IDLE_MODE_WAKEUP_PATTERN 0xd0ea1d1e
#define IDLE_MODE_WAKEUP_NOTIFIER_ADDRESS 0x1FC02FA8
#define IDLE_MODE_MAX_RETRY_COUNT 1000

#ifdef REL_4_1
#define CONFIG_BEGIN_ADDR 0xBF60B004
#else
#define CONFIG_BEGIN_ADDR 0xBF60B000
#endif

#define FIRMWARE_BEGIN_ADDR 0xBFC00000

#define INVALID_QUEUE_INDEX (USHORT)-1

#define INVALID_PID (pid_t)-1
#define DDR_80_MHZ      0
#define DDR_100_MHZ     1
#define DDR_120_MHZ     2 //  Additional Frequency for T3LP
#define DDR_133_MHZ     3
#define DDR_140_MHZ     4 //  Not Used (Reserved for future)
#define DDR_160_MHZ     5 //  Additional Frequency for T3LP
#define DDR_180_MHZ     6 //  Not Used (Reserved for future)
#define DDR_200_MHZ     7 //  Not Used (Reserved for future)

#define MIPS_200_MHZ   0
#define MIPS_160_MHZ   1

#define PLL_800_MHZ    0
#define PLL_266_MHZ    1

#define DEVICE_POWERSAVE_MODE_AS_MANUAL_CLOCK_GATING        0
#define DEVICE_POWERSAVE_MODE_AS_PMU_CLOCK_GATING           1
#define DEVICE_POWERSAVE_MODE_AS_PMU_SHUTDOWN               2
#define DEVICE_POWERSAVE_MODE_AS_RESERVED                   3
#define DEVICE_POWERSAVE_MODE_AS_PROTOCOL_IDLE_MODE         4


#define EEPROM_REJECT_REG_1 0x0f003018
#define EEPROM_REJECT_REG_2 0x0f00301c
#define EEPROM_REJECT_REG_3 0x0f003008
#define EEPROM_REJECT_REG_4 0x0f003020
#define EEPROM_REJECT_MASK  0x0fffffff
#define VSG_MODE                          0x3

/* Idle Mode Related Registers */
#define DEBUG_INTERRUPT_GENERATOR_REGISTOR 0x0F00007C
#define SW_ABORT_IDLEMODE_LOC           0x0FF01FFC

#define SW_ABORT_IDLEMODE_PATTERN       0xd0ea1d1e
#define DEVICE_INT_OUT_EP_REG0          0x0F011870
#define DEVICE_INT_OUT_EP_REG1          0x0F011874

#define BIN_FILE "/lib/firmware/macxvi200.bin"
#define CFG_FILE "/lib/firmware/macxvi.cfg"
#define SF_MAX_ALLOWED_PACKETS_TO_BACKUP 128
#define MIN_VAL(x,y)    ((x)<(y)?(x):(y))
#define MAC_ADDRESS_SIZE 6
#define EEPROM_COMMAND_Q_REG    0x0F003018
#define EEPROM_READ_DATA_Q_REG  0x0F003020
#define CHIP_ID_REG                     0x0F000000
#define GPIO_MODE_REG                   0x0F000034
#define GPIO_OUTPUT_REG                 0x0F00003C
#define WIMAX_MAX_ALLOWED_RATE  1024*1024*50

#define T3 0xbece0300
#define TARGET_SFID_TXDESC_MAP_LOC 0xBFFFF400

#define RWM_READ 0
#define RWM_WRITE 1

#define T3LPB       0xbece3300
#define BCS220_2        0xbece3311
#define BCS220_2BC      0xBECE3310
#define BCS250_BC       0xbece3301
#define BCS220_3        0xbece3321


#define HPM_CONFIG_LDO145       0x0F000D54
#define HPM_CONFIG_MSW          0x0F000D58

#define T3B 0xbece0310
typedef enum eNVM_TYPE
{
        NVM_AUTODETECT = 0,
        NVM_EEPROM,
        NVM_FLASH,
        NVM_UNKNOWN
}NVM_TYPE;

typedef enum ePMU_MODES
{
        HYBRID_MODE_7C  = 0,
        INTERNAL_MODE_6 = 1,
        HYBRID_MODE_6   = 2
}PMU_MODE;

#define MAX_RDM_WRM_RETIRES 1

enum eAbortPattern {
        ABORT_SHUTDOWN_MODE = 1,
        ABORT_IDLE_REG = 1,
        ABORT_IDLE_MODE = 2,
        ABORT_IDLE_SYNCDOWN = 3
};

#define GET_BCM_ADAPTER(net_dev) (net_dev ? netdev_priv(net_dev) : NULL)

/* Offsets used by driver in skb cb variable */
#define SKB_CB_CLASSIFICATION_OFFSET    0
#define SKB_CB_LATENCY_OFFSET           1
#define SKB_CB_TCPACK_OFFSET            2

#endif  //__MACROS_H__