4 * linux/include/linux/ide.h
6 * Copyright (C) 1994-2002 Linus Torvalds & authors
9 #include <linux/init.h>
10 #include <linux/ioport.h>
11 #include <linux/ata.h>
12 #include <linux/blkdev.h>
13 #include <linux/proc_fs.h>
14 #include <linux/interrupt.h>
15 #include <linux/bitops.h>
16 #include <linux/bio.h>
17 #include <linux/device.h>
18 #include <linux/pci.h>
19 #include <linux/completion.h>
21 #ifdef CONFIG_BLK_DEV_IDEACPI
22 #include <acpi/acpi.h>
24 #include <asm/byteorder.h>
25 #include <asm/system.h>
27 #include <asm/mutex.h>
29 #if defined(CONFIG_CRIS) || defined(CONFIG_FRV)
30 # define SUPPORT_VLB_SYNC 0
32 # define SUPPORT_VLB_SYNC 1
36 * Used to indicate "no IRQ", should be a value that cannot be an IRQ
40 #define IDE_NO_IRQ (-1)
42 typedef unsigned char byte
; /* used everywhere */
45 * Probably not wise to fiddle with these
47 #define ERROR_MAX 8 /* Max read/write errors per sector */
48 #define ERROR_RESET 3 /* Reset controller every 4th retry */
49 #define ERROR_RECAL 1 /* Recalibrate every 2nd retry */
55 #define DMA_PIO_RETRY 1 /* retrying in PIO */
57 #define HWIF(drive) ((ide_hwif_t *)((drive)->hwif))
58 #define HWGROUP(drive) ((ide_hwgroup_t *)(HWIF(drive)->hwgroup))
61 * Definitions for accessing IDE controller registers
63 #define IDE_NR_PORTS (10)
66 unsigned long data_addr
;
69 unsigned long error_addr
; /* read: error */
70 unsigned long feature_addr
; /* write: feature */
73 unsigned long nsect_addr
;
74 unsigned long lbal_addr
;
75 unsigned long lbam_addr
;
76 unsigned long lbah_addr
;
78 unsigned long device_addr
;
81 unsigned long status_addr
; /* read: status */
82 unsigned long command_addr
; /* write: command */
85 unsigned long ctl_addr
;
87 unsigned long irq_addr
;
90 #define OK_STAT(stat,good,bad) (((stat)&((good)|(bad)))==(good))
92 #define BAD_R_STAT (ATA_BUSY | ATA_ERR)
93 #define BAD_W_STAT (BAD_R_STAT | ATA_DF)
94 #define BAD_STAT (BAD_R_STAT | ATA_DRQ)
95 #define DRIVE_READY (ATA_DRDY | ATA_DSC)
97 #define BAD_CRC (ATA_ABORTED | ATA_ICRC)
99 #define SATA_NR_PORTS (3) /* 16 possible ?? */
101 #define SATA_STATUS_OFFSET (0)
102 #define SATA_ERROR_OFFSET (1)
103 #define SATA_CONTROL_OFFSET (2)
106 * Our Physical Region Descriptor (PRD) table should be large enough
107 * to handle the biggest I/O request we are likely to see. Since requests
108 * can have no more than 256 sectors, and since the typical blocksize is
109 * two or more sectors, we could get by with a limit of 128 entries here for
110 * the usual worst case. Most requests seem to include some contiguous blocks,
111 * further reducing the number of table entries required.
113 * The driver reverts to PIO mode for individual requests that exceed
114 * this limit (possible with 512 byte blocksizes, eg. MSDOS f/s), so handling
115 * 100% of all crazy scenarios here is not necessary.
117 * As it turns out though, we must allocate a full 4KB page for this,
118 * so the two PRD tables (ide0 & ide1) will each get half of that,
119 * allowing each to have about 256 entries (8 bytes each) from this.
122 #define PRD_ENTRIES 256
125 * Some more useful definitions
127 #define PARTN_BITS 6 /* number of minor dev bits for partitions */
128 #define MAX_DRIVES 2 /* per interface; 2 assumed by lots of code */
129 #define SECTOR_SIZE 512
131 #define IDE_LARGE_SEEK(b1,b2,t) (((b1) > (b2) + (t)) || ((b2) > (b1) + (t)))
134 * Timeouts for various operations:
137 /* spec allows up to 20ms */
138 WAIT_DRQ
= HZ
/ 10, /* 100ms */
139 /* some laptops are very slow */
140 WAIT_READY
= 5 * HZ
, /* 5s */
141 /* should be less than 3ms (?), if all ATAPI CD is closed at boot */
142 WAIT_PIDENTIFY
= 10 * HZ
, /* 10s */
143 /* worst case when spinning up */
144 WAIT_WORSTCASE
= 30 * HZ
, /* 30s */
145 /* maximum wait for an IRQ to happen */
146 WAIT_CMD
= 10 * HZ
, /* 10s */
147 /* Some drives require a longer IRQ timeout. */
148 WAIT_FLOPPY_CMD
= 50 * HZ
, /* 50s */
150 * Some drives (for example, Seagate STT3401A Travan) require a very
151 * long timeout, because they don't return an interrupt or clear their
152 * BSY bit until after the command completes (even retension commands).
154 WAIT_TAPE_CMD
= 900 * HZ
, /* 900s */
155 /* minimum sleep time */
156 WAIT_MIN_SLEEP
= HZ
/ 50, /* 20ms */
160 * Op codes for special requests to be handled by ide_special_rq().
161 * Values should be in the range of 0x20 to 0x3f.
163 #define REQ_DRIVE_RESET 0x20
164 #define REQ_DEVSET_EXEC 0x21
167 * Check for an interrupt and acknowledge the interrupt status
170 typedef int (ide_ack_intr_t
)(struct hwif_s
*);
173 * hwif_chipset_t is used to keep track of the specific hardware
174 * chipset used by each IDE interface, if known.
176 enum { ide_unknown
, ide_generic
, ide_pci
,
177 ide_cmd640
, ide_dtc2278
, ide_ali14xx
,
178 ide_qd65xx
, ide_umc8672
, ide_ht6560b
,
179 ide_rz1000
, ide_trm290
,
180 ide_cmd646
, ide_cy82c693
, ide_4drives
,
182 ide_au1xxx
, ide_palm3710
185 typedef u8 hwif_chipset_t
;
188 * Structure to hold all information about the location of this port
190 typedef struct hw_regs_s
{
192 struct ide_io_ports io_ports
;
193 unsigned long io_ports_array
[IDE_NR_PORTS
];
196 int irq
; /* our irq number */
197 ide_ack_intr_t
*ack_intr
; /* acknowledge interrupt */
198 hwif_chipset_t chipset
;
199 struct device
*dev
, *parent
;
200 unsigned long config
;
203 void ide_init_port_data(struct hwif_s
*, unsigned int);
204 void ide_init_port_hw(struct hwif_s
*, hw_regs_t
*);
206 static inline void ide_std_init_ports(hw_regs_t
*hw
,
207 unsigned long io_addr
,
208 unsigned long ctl_addr
)
212 for (i
= 0; i
<= 7; i
++)
213 hw
->io_ports_array
[i
] = io_addr
++;
215 hw
->io_ports
.ctl_addr
= ctl_addr
;
218 /* for IDE PCI controllers in legacy mode, temporary */
219 static inline int __ide_default_irq(unsigned long base
)
223 case 0x1f0: return isa_irq_to_vector(14);
224 case 0x170: return isa_irq_to_vector(15);
226 case 0x1f0: return 14;
227 case 0x170: return 15;
233 #if defined(CONFIG_ARM) || defined(CONFIG_FRV) || defined(CONFIG_M68K) || \
234 defined(CONFIG_MIPS) || defined(CONFIG_MN10300) || defined(CONFIG_PARISC) \
235 || defined(CONFIG_PPC) || defined(CONFIG_SPARC) || defined(CONFIG_SPARC64)
238 #include <asm-generic/ide_iops.h>
243 /* Currently only m68k, apus and m8xx need it */
244 #ifndef IDE_ARCH_ACK_INTR
245 # define ide_ack_intr(hwif) (1)
248 /* Currently only Atari needs it */
249 #ifndef IDE_ARCH_LOCK
250 # define ide_release_lock() do {} while (0)
251 # define ide_get_lock(hdlr, data) do {} while (0)
252 #endif /* IDE_ARCH_LOCK */
255 * Now for the data we need to maintain per-drive: ide_drive_t
258 #define ide_scsi 0x21
259 #define ide_disk 0x20
260 #define ide_optical 0x7
261 #define ide_cdrom 0x5
263 #define ide_floppy 0x0
266 * Special Driver Flags
268 * set_geometry : respecify drive geometry
269 * recalibrate : seek to cyl 0
270 * set_multmode : set multmode count
271 * set_tune : tune interface for drive
272 * serviced : service command
278 unsigned set_geometry
: 1;
279 unsigned recalibrate
: 1;
280 unsigned set_multmode
: 1;
281 unsigned set_tune
: 1;
282 unsigned serviced
: 1;
283 unsigned reserved
: 3;
288 * ATA-IDE Select Register, aka Device-Head
290 * head : always zeros here
291 * unit : drive select number: 0/1
293 * lba : using LBA instead of CHS
299 #if defined(__LITTLE_ENDIAN_BITFIELD)
305 #elif defined(__BIG_ENDIAN_BITFIELD)
312 #error "Please fix <asm/byteorder.h>"
315 } select_t
, ata_select_t
;
318 * Status returned from various ide_ functions
321 ide_stopped
, /* no drive operation was started */
322 ide_started
, /* a drive operation was started, handler was set */
325 /* ATAPI packet command flags */
327 /* set when an error is considered normal - no retry (ide-tape) */
328 PC_FLAG_ABORT
= (1 << 0),
329 PC_FLAG_SUPPRESS_ERROR
= (1 << 1),
330 PC_FLAG_WAIT_FOR_DSC
= (1 << 2),
331 PC_FLAG_DMA_OK
= (1 << 3),
332 PC_FLAG_DMA_IN_PROGRESS
= (1 << 4),
333 PC_FLAG_DMA_ERROR
= (1 << 5),
334 PC_FLAG_WRITING
= (1 << 6),
335 /* command timed out */
336 PC_FLAG_TIMEDOUT
= (1 << 7),
340 * With each packet command, we allocate a buffer of IDE_PC_BUFFER_SIZE bytes.
341 * This is used for several packet commands (not for READ/WRITE commands).
343 #define IDE_PC_BUFFER_SIZE 256
345 struct ide_atapi_pc
{
346 /* actual packet bytes */
348 /* incremented on each retry */
352 /* bytes to transfer */
354 /* bytes actually transferred */
359 /* current buffer position */
362 /* missing/available data on the current buffer */
365 /* the corresponding request */
371 * those are more or less driver-specific and some of them are subject
372 * to change/removal later.
374 u8 pc_buf
[IDE_PC_BUFFER_SIZE
];
377 struct idetape_bh
*bh
;
380 /* idescsi only for now */
381 struct scatterlist
*sg
;
384 struct scsi_cmnd
*scsi_cmd
;
385 void (*done
) (struct scsi_cmnd
*);
387 unsigned long timeout
;
393 #ifdef CONFIG_BLK_DEV_IDEACPI
394 struct ide_acpi_drive_link
;
395 struct ide_acpi_hwif_link
;
398 /* ATAPI device flags */
400 IDE_AFLAG_DRQ_INTERRUPT
= (1 << 0),
401 IDE_AFLAG_MEDIA_CHANGED
= (1 << 1),
402 /* Drive cannot lock the door. */
403 IDE_AFLAG_NO_DOORLOCK
= (1 << 2),
406 /* Drive cannot eject the disc. */
407 IDE_AFLAG_NO_EJECT
= (1 << 3),
408 /* Drive is a pre ATAPI 1.2 drive. */
409 IDE_AFLAG_PRE_ATAPI12
= (1 << 4),
410 /* TOC addresses are in BCD. */
411 IDE_AFLAG_TOCADDR_AS_BCD
= (1 << 5),
412 /* TOC track numbers are in BCD. */
413 IDE_AFLAG_TOCTRACKS_AS_BCD
= (1 << 6),
415 * Drive does not provide data in multiples of SECTOR_SIZE
416 * when more than one interrupt is needed.
418 IDE_AFLAG_LIMIT_NFRAMES
= (1 << 7),
419 /* Seeking in progress. */
420 IDE_AFLAG_SEEKING
= (1 << 8),
421 /* Saved TOC information is current. */
422 IDE_AFLAG_TOC_VALID
= (1 << 9),
423 /* We think that the drive door is locked. */
424 IDE_AFLAG_DOOR_LOCKED
= (1 << 10),
425 /* SET_CD_SPEED command is unsupported. */
426 IDE_AFLAG_NO_SPEED_SELECT
= (1 << 11),
427 IDE_AFLAG_VERTOS_300_SSD
= (1 << 12),
428 IDE_AFLAG_VERTOS_600_ESD
= (1 << 13),
429 IDE_AFLAG_SANYO_3CD
= (1 << 14),
430 IDE_AFLAG_FULL_CAPS_PAGE
= (1 << 15),
431 IDE_AFLAG_PLAY_AUDIO_OK
= (1 << 16),
432 IDE_AFLAG_LE_SPEED_FIELDS
= (1 << 17),
435 /* Format in progress */
436 IDE_AFLAG_FORMAT_IN_PROGRESS
= (1 << 18),
437 /* Avoid commands not supported in Clik drive */
438 IDE_AFLAG_CLIK_DRIVE
= (1 << 19),
439 /* Requires BH algorithm for packets */
440 IDE_AFLAG_ZIP_DRIVE
= (1 << 20),
442 IDE_AFLAG_WP
= (1 << 21),
443 /* Supports format progress report */
444 IDE_AFLAG_SRFP
= (1 << 22),
447 IDE_AFLAG_IGNORE_DSC
= (1 << 23),
448 /* 0 When the tape position is unknown */
449 IDE_AFLAG_ADDRESS_VALID
= (1 << 24),
450 /* Device already opened */
451 IDE_AFLAG_BUSY
= (1 << 25),
452 /* Attempt to auto-detect the current user block size */
453 IDE_AFLAG_DETECT_BS
= (1 << 26),
454 /* Currently on a filemark */
455 IDE_AFLAG_FILEMARK
= (1 << 27),
456 /* 0 = no tape is loaded, so we don't rewind after ejecting */
457 IDE_AFLAG_MEDIUM_PRESENT
= (1 << 28),
459 IDE_AFLAG_NO_AUTOCLOSE
= (1 << 29),
463 char name
[4]; /* drive name, such as "hda" */
464 char driver_req
[10]; /* requests specific driver */
466 struct request_queue
*queue
; /* request queue */
468 struct request
*rq
; /* current request */
469 struct ide_drive_s
*next
; /* circular list of hwgroup drives */
470 void *driver_data
; /* extra driver data */
471 u16
*id
; /* identification info */
472 #ifdef CONFIG_IDE_PROC_FS
473 struct proc_dir_entry
*proc
; /* /proc/ide/ directory entry */
474 const struct ide_proc_devset
*settings
; /* /proc/ide/ drive settings */
476 struct hwif_s
*hwif
; /* actually (ide_hwif_t *) */
478 unsigned long sleep
; /* sleep until this time */
479 unsigned long service_start
; /* time we started last request */
480 unsigned long service_time
; /* service time of last request */
481 unsigned long timeout
; /* max time to wait for irq */
483 special_t special
; /* special action flags */
484 select_t select
; /* basic drive/head select reg value */
486 u8 retry_pio
; /* retrying dma capable host in pio */
487 u8 state
; /* retry state */
488 u8 waiting_for_dma
; /* dma currently in progress */
490 unsigned keep_settings
: 1; /* restore settings after drive reset */
491 unsigned using_dma
: 1; /* disk is using dma for read/write */
492 unsigned unmask
: 1; /* okay to unmask other irqs */
493 unsigned noflush
: 1; /* don't attempt flushes */
494 unsigned dsc_overlap
: 1; /* DSC overlap */
495 unsigned nice1
: 1; /* give potential excess bandwidth */
496 unsigned present
: 1; /* drive is physically present */
497 unsigned dead
: 1; /* device ejected hint */
498 unsigned id_read
: 1; /* 1=id read from disk 0 = synthetic */
499 unsigned noprobe
: 1; /* from: hdx=noprobe */
500 unsigned removable
: 1; /* 1 if need to do check_media_change */
501 unsigned attach
: 1; /* needed for removable devices */
502 unsigned forced_geom
: 1; /* 1 if hdx=c,h,s was given at boot */
503 unsigned no_unmask
: 1; /* disallow setting unmask bit */
504 unsigned no_io_32bit
: 1; /* disallow enabling 32bit I/O */
505 unsigned doorlocking
: 1; /* for removable only: door lock/unlock works */
506 unsigned nodma
: 1; /* disallow DMA */
507 unsigned blocked
: 1; /* 1=powermanagment told us not to do anything, so sleep nicely */
508 unsigned scsi
: 1; /* 0=default, 1=ide-scsi emulation */
509 unsigned sleeping
: 1; /* 1=sleeping & sleep field valid */
510 unsigned post_reset
: 1;
511 unsigned udma33_warned
: 1;
512 unsigned addressing
: 2; /* 0=28-bit, 1=48-bit, 2=48-bit doing 28-bit */
513 unsigned wcache
: 1; /* status of write cache */
514 unsigned nowerr
: 1; /* used for ignoring ATA_DF */
516 u8 quirk_list
; /* considered quirky, set for a specific host */
517 u8 init_speed
; /* transfer rate set at boot */
518 u8 current_speed
; /* current transfer rate set */
519 u8 desired_speed
; /* desired transfer rate set */
520 u8 dn
; /* now wide spread use */
521 u8 acoustic
; /* acoustic management */
522 u8 media
; /* disk, cdrom, tape, floppy, ... */
523 u8 ready_stat
; /* min status value for drive ready */
524 u8 mult_count
; /* current multiple sector setting */
525 u8 mult_req
; /* requested multiple sector setting */
526 u8 tune_req
; /* requested drive tuning setting */
527 u8 io_32bit
; /* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
528 u8 bad_wstat
; /* used for ignoring ATA_DF */
529 u8 head
; /* "real" number of heads */
530 u8 sect
; /* "real" sectors per track */
531 u8 bios_head
; /* BIOS/fdisk/LILO number of heads */
532 u8 bios_sect
; /* BIOS/fdisk/LILO sectors per track */
534 unsigned int bios_cyl
; /* BIOS/fdisk/LILO number of cyls */
535 unsigned int cyl
; /* "real" number of cyls */
536 unsigned int drive_data
; /* used by set_pio_mode/selectproc */
537 unsigned int failures
; /* current failure count */
538 unsigned int max_failures
; /* maximum allowed failure count */
539 u64 probed_capacity
;/* initial reported media capacity (ide-cd only currently) */
541 u64 capacity64
; /* total number of sectors */
543 int lun
; /* logical unit */
544 int crc_count
; /* crc counter to reduce drive speed */
545 #ifdef CONFIG_BLK_DEV_IDEACPI
546 struct ide_acpi_drive_link
*acpidata
;
548 struct list_head list
;
549 struct device gendev
;
550 struct completion gendev_rel_comp
; /* to deal with device release() */
552 /* current packet command */
553 struct ide_atapi_pc
*pc
;
555 /* callback for packet commands */
556 void (*pc_callback
)(struct ide_drive_s
*, int);
558 void (*pc_update_buffers
)(struct ide_drive_s
*, struct ide_atapi_pc
*);
559 int (*pc_io_buffers
)(struct ide_drive_s
*, struct ide_atapi_pc
*,
562 unsigned long atapi_flags
;
564 struct ide_atapi_pc request_sense_pc
;
565 struct request request_sense_rq
;
568 typedef struct ide_drive_s ide_drive_t
;
570 #define to_ide_device(dev)container_of(dev, ide_drive_t, gendev)
573 struct ide_port_info
;
576 void (*exec_command
)(struct hwif_s
*, u8
);
577 u8 (*read_status
)(struct hwif_s
*);
578 u8 (*read_altstatus
)(struct hwif_s
*);
579 u8 (*read_sff_dma_status
)(struct hwif_s
*);
581 void (*set_irq
)(struct hwif_s
*, int);
583 void (*tf_load
)(ide_drive_t
*, struct ide_task_s
*);
584 void (*tf_read
)(ide_drive_t
*, struct ide_task_s
*);
586 void (*input_data
)(ide_drive_t
*, struct request
*, void *,
588 void (*output_data
)(ide_drive_t
*, struct request
*, void *,
592 extern const struct ide_tp_ops default_tp_ops
;
595 * struct ide_port_ops - IDE port operations
597 * @init_dev: host specific initialization of a device
598 * @set_pio_mode: routine to program host for PIO mode
599 * @set_dma_mode: routine to program host for DMA mode
600 * @selectproc: tweaks hardware to select drive
601 * @reset_poll: chipset polling based on hba specifics
602 * @pre_reset: chipset specific changes to default for device-hba resets
603 * @resetproc: routine to reset controller after a disk reset
604 * @maskproc: special host masking for drive selection
605 * @quirkproc: check host's drive quirk list
607 * @mdma_filter: filter MDMA modes
608 * @udma_filter: filter UDMA modes
610 * @cable_detect: detect cable type
612 struct ide_port_ops
{
613 void (*init_dev
)(ide_drive_t
*);
614 void (*set_pio_mode
)(ide_drive_t
*, const u8
);
615 void (*set_dma_mode
)(ide_drive_t
*, const u8
);
616 void (*selectproc
)(ide_drive_t
*);
617 int (*reset_poll
)(ide_drive_t
*);
618 void (*pre_reset
)(ide_drive_t
*);
619 void (*resetproc
)(ide_drive_t
*);
620 void (*maskproc
)(ide_drive_t
*, int);
621 void (*quirkproc
)(ide_drive_t
*);
623 u8 (*mdma_filter
)(ide_drive_t
*);
624 u8 (*udma_filter
)(ide_drive_t
*);
626 u8 (*cable_detect
)(struct hwif_s
*);
630 void (*dma_host_set
)(struct ide_drive_s
*, int);
631 int (*dma_setup
)(struct ide_drive_s
*);
632 void (*dma_exec_cmd
)(struct ide_drive_s
*, u8
);
633 void (*dma_start
)(struct ide_drive_s
*);
634 int (*dma_end
)(struct ide_drive_s
*);
635 int (*dma_test_irq
)(struct ide_drive_s
*);
636 void (*dma_lost_irq
)(struct ide_drive_s
*);
637 void (*dma_timeout
)(struct ide_drive_s
*);
642 typedef struct hwif_s
{
643 struct hwif_s
*next
; /* for linked-list in ide_hwgroup_t */
644 struct hwif_s
*mate
; /* other hwif from same PCI chip */
645 struct hwgroup_s
*hwgroup
; /* actually (ide_hwgroup_t *) */
646 struct proc_dir_entry
*proc
; /* /proc/ide/ directory entry */
648 struct ide_host
*host
;
650 char name
[6]; /* name of interface, eg. "ide0" */
652 struct ide_io_ports io_ports
;
654 unsigned long sata_scr
[SATA_NR_PORTS
];
656 ide_drive_t drives
[MAX_DRIVES
]; /* drive info */
658 u8 major
; /* our major number */
659 u8 index
; /* 0 for ide0; 1 for ide1; ... */
660 u8 channel
; /* for dual-port chips: 0=primary, 1=secondary */
670 u8 cbl
; /* cable type */
672 hwif_chipset_t chipset
; /* sub-module for tuning.. */
676 ide_ack_intr_t
*ack_intr
;
678 void (*rw_disk
)(ide_drive_t
*, struct request
*);
680 const struct ide_tp_ops
*tp_ops
;
681 const struct ide_port_ops
*port_ops
;
682 const struct ide_dma_ops
*dma_ops
;
684 void (*ide_dma_clear_irq
)(ide_drive_t
*drive
);
686 /* dma physical region descriptor table (cpu view) */
687 unsigned int *dmatable_cpu
;
688 /* dma physical region descriptor table (dma view) */
689 dma_addr_t dmatable_dma
;
690 /* Scatter-gather list used to build the above */
691 struct scatterlist
*sg_table
;
692 int sg_max_nents
; /* Maximum number of entries in it */
693 int sg_nents
; /* Current number of entries in it */
694 int sg_dma_direction
; /* dma transfer direction */
696 /* data phase of the active command (currently only valid for PIO/DMA) */
701 struct scatterlist
*cursg
;
702 unsigned int cursg_ofs
;
704 int rqsize
; /* max sectors per request */
705 int irq
; /* our irq number */
707 unsigned long dma_base
; /* base addr for dma ports */
709 unsigned long config_data
; /* for use by chipset-specific code */
710 unsigned long select_data
; /* for use by chipset-specific code */
712 unsigned long extra_base
; /* extra addr for dma ports */
713 unsigned extra_ports
; /* number of extra dma ports */
715 unsigned present
: 1; /* this interface exists */
716 unsigned serialized
: 1; /* serialized all channel operation */
717 unsigned sharing_irq
: 1; /* 1 = sharing irq with another hwif */
718 unsigned sg_mapped
: 1; /* sg_table and sg_nents are ready */
720 struct device gendev
;
721 struct device
*portdev
;
723 struct completion gendev_rel_comp
; /* To deal with device release() */
725 void *hwif_data
; /* extra hwif data */
729 #ifdef CONFIG_BLK_DEV_IDEACPI
730 struct ide_acpi_hwif_link
*acpidata
;
732 } ____cacheline_internodealigned_in_smp ide_hwif_t
;
735 ide_hwif_t
*ports
[MAX_HWIFS
];
736 unsigned int n_ports
;
737 struct device
*dev
[2];
738 unsigned int (*init_chipset
)(struct pci_dev
*);
739 unsigned long host_flags
;
744 * internal ide interrupt handler type
746 typedef ide_startstop_t (ide_handler_t
)(ide_drive_t
*);
747 typedef int (ide_expiry_t
)(ide_drive_t
*);
749 /* used by ide-cd, ide-floppy, etc. */
750 typedef void (xfer_func_t
)(ide_drive_t
*, struct request
*rq
, void *, unsigned);
752 typedef struct hwgroup_s
{
753 /* irq handler, if active */
754 ide_startstop_t (*handler
)(ide_drive_t
*);
756 /* BOOL: protects all fields below */
758 /* BOOL: wake us up on timer expiry */
759 unsigned int sleeping
: 1;
760 /* BOOL: polling active & poll_timeout field valid */
761 unsigned int polling
: 1;
765 /* ptr to current hwif in linked-list */
768 /* current request */
772 struct timer_list timer
;
773 /* timeout value during long polls */
774 unsigned long poll_timeout
;
775 /* queried upon timeouts */
776 int (*expiry
)(ide_drive_t
*);
782 typedef struct ide_driver_s ide_driver_t
;
784 extern struct mutex ide_setting_mtx
;
787 * configurable drive settings
790 #define DS_SYNC (1 << 0)
793 int (*get
)(ide_drive_t
*);
794 int (*set
)(ide_drive_t
*, int);
798 #define __DEVSET(_flags, _get, _set) { \
804 #define ide_devset_get(name, field) \
805 static int get_##name(ide_drive_t *drive) \
807 return drive->field; \
810 #define ide_devset_set(name, field) \
811 static int set_##name(ide_drive_t *drive, int arg) \
813 drive->field = arg; \
817 #define __IDE_DEVSET(_name, _flags, _get, _set) \
818 const struct ide_devset ide_devset_##_name = \
819 __DEVSET(_flags, _get, _set)
821 #define IDE_DEVSET(_name, _flags, _get, _set) \
822 static __IDE_DEVSET(_name, _flags, _get, _set)
824 #define ide_devset_rw(_name, _func) \
825 IDE_DEVSET(_name, 0, get_##_func, set_##_func)
827 #define ide_devset_w(_name, _func) \
828 IDE_DEVSET(_name, 0, NULL, set_##_func)
830 #define ide_devset_rw_sync(_name, _func) \
831 IDE_DEVSET(_name, DS_SYNC, get_##_func, set_##_func)
833 #define ide_decl_devset(_name) \
834 extern const struct ide_devset ide_devset_##_name
836 ide_decl_devset(io_32bit
);
837 ide_decl_devset(keepsettings
);
838 ide_decl_devset(pio_mode
);
839 ide_decl_devset(unmaskirq
);
840 ide_decl_devset(using_dma
);
842 #ifdef CONFIG_IDE_PROC_FS
844 * /proc/ide interface
847 #define ide_devset_rw_field(_name, _field) \
848 ide_devset_get(_name, _field); \
849 ide_devset_set(_name, _field); \
850 IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
852 struct ide_proc_devset
{
854 const struct ide_devset
*setting
;
856 int (*mulf
)(ide_drive_t
*);
857 int (*divf
)(ide_drive_t
*);
860 #define __IDE_PROC_DEVSET(_name, _min, _max, _mulf, _divf) { \
861 .name = __stringify(_name), \
862 .setting = &ide_devset_##_name, \
869 #define IDE_PROC_DEVSET(_name, _min, _max) \
870 __IDE_PROC_DEVSET(_name, _min, _max, NULL, NULL)
875 read_proc_t
*read_proc
;
876 write_proc_t
*write_proc
;
879 void proc_ide_create(void);
880 void proc_ide_destroy(void);
881 void ide_proc_register_port(ide_hwif_t
*);
882 void ide_proc_port_register_devices(ide_hwif_t
*);
883 void ide_proc_unregister_device(ide_drive_t
*);
884 void ide_proc_unregister_port(ide_hwif_t
*);
885 void ide_proc_register_driver(ide_drive_t
*, ide_driver_t
*);
886 void ide_proc_unregister_driver(ide_drive_t
*, ide_driver_t
*);
888 read_proc_t proc_ide_read_capacity
;
889 read_proc_t proc_ide_read_geometry
;
892 * Standard exit stuff:
894 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) \
903 *start = page + off; \
907 static inline void proc_ide_create(void) { ; }
908 static inline void proc_ide_destroy(void) { ; }
909 static inline void ide_proc_register_port(ide_hwif_t
*hwif
) { ; }
910 static inline void ide_proc_port_register_devices(ide_hwif_t
*hwif
) { ; }
911 static inline void ide_proc_unregister_device(ide_drive_t
*drive
) { ; }
912 static inline void ide_proc_unregister_port(ide_hwif_t
*hwif
) { ; }
913 static inline void ide_proc_register_driver(ide_drive_t
*drive
, ide_driver_t
*driver
) { ; }
914 static inline void ide_proc_unregister_driver(ide_drive_t
*drive
, ide_driver_t
*driver
) { ; }
915 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) return 0;
919 * Power Management step value (rq->pm->pm_step).
921 * The step value starts at 0 (ide_pm_state_start_suspend) for a
922 * suspend operation or 1000 (ide_pm_state_start_resume) for a
925 * For each step, the core calls the subdriver start_power_step() first.
927 * - ide_stopped : In this case, the core calls us back again unless
928 * step have been set to ide_power_state_completed.
929 * - ide_started : In this case, the channel is left busy until an
930 * async event (interrupt) occurs.
931 * Typically, start_power_step() will issue a taskfile request with
934 * Upon reception of the interrupt, the core will call complete_power_step()
935 * with the error code if any. This routine should update the step value
936 * and return. It should not start a new request. The core will call
937 * start_power_step for the new step value, unless step have been set to
938 * ide_power_state_completed.
940 * Subdrivers are expected to define their own additional power
941 * steps from 1..999 for suspend and from 1001..1999 for resume,
942 * other values are reserved for future use.
946 ide_pm_state_completed
= -1,
947 ide_pm_state_start_suspend
= 0,
948 ide_pm_state_start_resume
= 1000,
952 * Subdrivers support.
954 * The gendriver.owner field should be set to the module owner of this driver.
955 * The gendriver.name field should be set to the name of this driver
957 struct ide_driver_s
{
960 ide_startstop_t (*do_request
)(ide_drive_t
*, struct request
*, sector_t
);
961 int (*end_request
)(ide_drive_t
*, int, int);
962 ide_startstop_t (*error
)(ide_drive_t
*, struct request
*rq
, u8
, u8
);
963 struct device_driver gen_driver
;
964 int (*probe
)(ide_drive_t
*);
965 void (*remove
)(ide_drive_t
*);
966 void (*resume
)(ide_drive_t
*);
967 void (*shutdown
)(ide_drive_t
*);
968 #ifdef CONFIG_IDE_PROC_FS
969 ide_proc_entry_t
*proc
;
970 const struct ide_proc_devset
*settings
;
974 #define to_ide_driver(drv) container_of(drv, ide_driver_t, gen_driver)
976 int ide_device_get(ide_drive_t
*);
977 void ide_device_put(ide_drive_t
*);
979 struct ide_ioctl_devset
{
980 unsigned int get_ioctl
;
981 unsigned int set_ioctl
;
982 const struct ide_devset
*setting
;
985 int ide_setting_ioctl(ide_drive_t
*, struct block_device
*, unsigned int,
986 unsigned long, const struct ide_ioctl_devset
*);
988 int generic_ide_ioctl(ide_drive_t
*, struct file
*, struct block_device
*,
989 unsigned, unsigned long);
991 extern int ide_vlb_clk
;
992 extern int ide_pci_clk
;
994 extern int ide_end_request (ide_drive_t
*drive
, int uptodate
, int nrsecs
);
995 int ide_end_dequeued_request(ide_drive_t
*drive
, struct request
*rq
,
996 int uptodate
, int nr_sectors
);
998 extern void ide_set_handler (ide_drive_t
*drive
, ide_handler_t
*handler
, unsigned int timeout
, ide_expiry_t
*expiry
);
1000 void ide_execute_command(ide_drive_t
*, u8
, ide_handler_t
*, unsigned int,
1003 void ide_execute_pkt_cmd(ide_drive_t
*);
1005 void ide_pad_transfer(ide_drive_t
*, int, int);
1007 ide_startstop_t
__ide_error(ide_drive_t
*, struct request
*, u8
, u8
);
1009 ide_startstop_t
ide_error (ide_drive_t
*drive
, const char *msg
, byte stat
);
1011 void ide_fix_driveid(u16
*);
1013 extern void ide_fixstring(u8
*, const int, const int);
1015 int ide_busy_sleep(ide_hwif_t
*, unsigned long, int);
1017 int ide_wait_stat(ide_startstop_t
*, ide_drive_t
*, u8
, u8
, unsigned long);
1019 extern ide_startstop_t
ide_do_reset (ide_drive_t
*);
1021 extern int ide_devset_execute(ide_drive_t
*drive
,
1022 const struct ide_devset
*setting
, int arg
);
1024 extern void ide_do_drive_cmd(ide_drive_t
*, struct request
*);
1026 extern void ide_end_drive_cmd(ide_drive_t
*, u8
, u8
);
1029 IDE_TFLAG_LBA48
= (1 << 0),
1030 IDE_TFLAG_FLAGGED
= (1 << 2),
1031 IDE_TFLAG_OUT_DATA
= (1 << 3),
1032 IDE_TFLAG_OUT_HOB_FEATURE
= (1 << 4),
1033 IDE_TFLAG_OUT_HOB_NSECT
= (1 << 5),
1034 IDE_TFLAG_OUT_HOB_LBAL
= (1 << 6),
1035 IDE_TFLAG_OUT_HOB_LBAM
= (1 << 7),
1036 IDE_TFLAG_OUT_HOB_LBAH
= (1 << 8),
1037 IDE_TFLAG_OUT_HOB
= IDE_TFLAG_OUT_HOB_FEATURE
|
1038 IDE_TFLAG_OUT_HOB_NSECT
|
1039 IDE_TFLAG_OUT_HOB_LBAL
|
1040 IDE_TFLAG_OUT_HOB_LBAM
|
1041 IDE_TFLAG_OUT_HOB_LBAH
,
1042 IDE_TFLAG_OUT_FEATURE
= (1 << 9),
1043 IDE_TFLAG_OUT_NSECT
= (1 << 10),
1044 IDE_TFLAG_OUT_LBAL
= (1 << 11),
1045 IDE_TFLAG_OUT_LBAM
= (1 << 12),
1046 IDE_TFLAG_OUT_LBAH
= (1 << 13),
1047 IDE_TFLAG_OUT_TF
= IDE_TFLAG_OUT_FEATURE
|
1048 IDE_TFLAG_OUT_NSECT
|
1049 IDE_TFLAG_OUT_LBAL
|
1050 IDE_TFLAG_OUT_LBAM
|
1052 IDE_TFLAG_OUT_DEVICE
= (1 << 14),
1053 IDE_TFLAG_WRITE
= (1 << 15),
1054 IDE_TFLAG_FLAGGED_SET_IN_FLAGS
= (1 << 16),
1055 IDE_TFLAG_IN_DATA
= (1 << 17),
1056 IDE_TFLAG_CUSTOM_HANDLER
= (1 << 18),
1057 IDE_TFLAG_DMA_PIO_FALLBACK
= (1 << 19),
1058 IDE_TFLAG_IN_HOB_FEATURE
= (1 << 20),
1059 IDE_TFLAG_IN_HOB_NSECT
= (1 << 21),
1060 IDE_TFLAG_IN_HOB_LBAL
= (1 << 22),
1061 IDE_TFLAG_IN_HOB_LBAM
= (1 << 23),
1062 IDE_TFLAG_IN_HOB_LBAH
= (1 << 24),
1063 IDE_TFLAG_IN_HOB_LBA
= IDE_TFLAG_IN_HOB_LBAL
|
1064 IDE_TFLAG_IN_HOB_LBAM
|
1065 IDE_TFLAG_IN_HOB_LBAH
,
1066 IDE_TFLAG_IN_HOB
= IDE_TFLAG_IN_HOB_FEATURE
|
1067 IDE_TFLAG_IN_HOB_NSECT
|
1068 IDE_TFLAG_IN_HOB_LBA
,
1069 IDE_TFLAG_IN_FEATURE
= (1 << 1),
1070 IDE_TFLAG_IN_NSECT
= (1 << 25),
1071 IDE_TFLAG_IN_LBAL
= (1 << 26),
1072 IDE_TFLAG_IN_LBAM
= (1 << 27),
1073 IDE_TFLAG_IN_LBAH
= (1 << 28),
1074 IDE_TFLAG_IN_LBA
= IDE_TFLAG_IN_LBAL
|
1077 IDE_TFLAG_IN_TF
= IDE_TFLAG_IN_NSECT
|
1079 IDE_TFLAG_IN_DEVICE
= (1 << 29),
1080 IDE_TFLAG_HOB
= IDE_TFLAG_OUT_HOB
|
1082 IDE_TFLAG_TF
= IDE_TFLAG_OUT_TF
|
1084 IDE_TFLAG_DEVICE
= IDE_TFLAG_OUT_DEVICE
|
1085 IDE_TFLAG_IN_DEVICE
,
1086 /* force 16-bit I/O operations */
1087 IDE_TFLAG_IO_16BIT
= (1 << 30),
1088 /* ide_task_t was allocated using kmalloc() */
1089 IDE_TFLAG_DYN
= (1 << 31),
1092 struct ide_taskfile
{
1093 u8 hob_data
; /* 0: high data byte (for TASKFILE IOCTL) */
1095 u8 hob_feature
; /* 1-5: additional data to support LBA48 */
1101 u8 data
; /* 6: low data byte (for TASKFILE IOCTL) */
1104 u8 error
; /* read: error */
1105 u8 feature
; /* write: feature */
1108 u8 nsect
; /* 8: number of sectors */
1109 u8 lbal
; /* 9: LBA low */
1110 u8 lbam
; /* 10: LBA mid */
1111 u8 lbah
; /* 11: LBA high */
1113 u8 device
; /* 12: device select */
1116 u8 status
; /* read: status */
1117 u8 command
; /* write: command */
1121 typedef struct ide_task_s
{
1123 struct ide_taskfile tf
;
1128 struct request
*rq
; /* copy of request */
1129 void *special
; /* valid_t generally */
1132 void ide_tf_dump(const char *, struct ide_taskfile
*);
1134 void ide_exec_command(ide_hwif_t
*, u8
);
1135 u8
ide_read_status(ide_hwif_t
*);
1136 u8
ide_read_altstatus(ide_hwif_t
*);
1137 u8
ide_read_sff_dma_status(ide_hwif_t
*);
1139 void ide_set_irq(ide_hwif_t
*, int);
1141 void ide_tf_load(ide_drive_t
*, ide_task_t
*);
1142 void ide_tf_read(ide_drive_t
*, ide_task_t
*);
1144 void ide_input_data(ide_drive_t
*, struct request
*, void *, unsigned int);
1145 void ide_output_data(ide_drive_t
*, struct request
*, void *, unsigned int);
1147 int ide_io_buffers(ide_drive_t
*, struct ide_atapi_pc
*, unsigned int, int);
1149 extern void SELECT_DRIVE(ide_drive_t
*);
1150 void SELECT_MASK(ide_drive_t
*, int);
1152 u8
ide_read_error(ide_drive_t
*);
1153 void ide_read_bcount_and_ireason(ide_drive_t
*, u16
*, u8
*);
1155 extern int drive_is_ready(ide_drive_t
*);
1157 void ide_pktcmd_tf_load(ide_drive_t
*, u32
, u16
, u8
);
1159 int ide_check_atapi_device(ide_drive_t
*, const char *);
1161 void ide_init_pc(struct ide_atapi_pc
*);
1164 * Special requests for ide-tape block device strategy routine.
1166 * In order to service a character device command, we add special requests to
1167 * the tail of our block device request queue and wait for their completion.
1170 REQ_IDETAPE_PC1
= (1 << 0), /* packet command (first stage) */
1171 REQ_IDETAPE_PC2
= (1 << 1), /* packet command (second stage) */
1172 REQ_IDETAPE_READ
= (1 << 2),
1173 REQ_IDETAPE_WRITE
= (1 << 3),
1176 int ide_queue_pc_tail(ide_drive_t
*, struct gendisk
*, struct ide_atapi_pc
*);
1178 int ide_do_test_unit_ready(ide_drive_t
*, struct gendisk
*);
1179 int ide_do_start_stop(ide_drive_t
*, struct gendisk
*, int);
1180 int ide_set_media_lock(ide_drive_t
*, struct gendisk
*, int);
1181 void ide_create_request_sense_cmd(ide_drive_t
*, struct ide_atapi_pc
*);
1182 void ide_retry_pc(ide_drive_t
*, struct gendisk
*);
1184 static inline unsigned long ide_scsi_get_timeout(struct ide_atapi_pc
*pc
)
1186 return max_t(unsigned long, WAIT_CMD
, pc
->timeout
- jiffies
);
1189 int ide_scsi_expiry(ide_drive_t
*);
1191 ide_startstop_t
ide_transfer_pc(ide_drive_t
*, unsigned int, ide_expiry_t
*);
1192 ide_startstop_t
ide_issue_pc(ide_drive_t
*,
1193 ide_handler_t
*, unsigned int, ide_expiry_t
*);
1195 ide_startstop_t
do_rw_taskfile(ide_drive_t
*, ide_task_t
*);
1197 void task_end_request(ide_drive_t
*, struct request
*, u8
);
1199 int ide_raw_taskfile(ide_drive_t
*, ide_task_t
*, u8
*, u16
);
1200 int ide_no_data_taskfile(ide_drive_t
*, ide_task_t
*);
1202 int ide_taskfile_ioctl(ide_drive_t
*, unsigned int, unsigned long);
1204 extern int ide_driveid_update(ide_drive_t
*);
1205 extern int ide_config_drive_speed(ide_drive_t
*, u8
);
1206 extern u8
eighty_ninty_three (ide_drive_t
*);
1207 extern int taskfile_lib_get_identify(ide_drive_t
*drive
, u8
*);
1209 extern int ide_wait_not_busy(ide_hwif_t
*hwif
, unsigned long timeout
);
1211 extern void ide_stall_queue(ide_drive_t
*drive
, unsigned long timeout
);
1213 extern void ide_timer_expiry(unsigned long);
1214 extern irqreturn_t
ide_intr(int irq
, void *dev_id
);
1215 extern void do_ide_request(struct request_queue
*);
1217 void ide_init_disk(struct gendisk
*, ide_drive_t
*);
1219 #ifdef CONFIG_IDEPCI_PCIBUS_ORDER
1220 extern int __ide_pci_register_driver(struct pci_driver
*driver
, struct module
*owner
, const char *mod_name
);
1221 #define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME)
1223 #define ide_pci_register_driver(d) pci_register_driver(d)
1226 void ide_pci_setup_ports(struct pci_dev
*, const struct ide_port_info
*, int,
1227 hw_regs_t
*, hw_regs_t
**);
1228 void ide_setup_pci_noise(struct pci_dev
*, const struct ide_port_info
*);
1230 #ifdef CONFIG_BLK_DEV_IDEDMA_PCI
1231 int ide_pci_set_master(struct pci_dev
*, const char *);
1232 unsigned long ide_pci_dma_base(ide_hwif_t
*, const struct ide_port_info
*);
1233 int ide_pci_check_simplex(ide_hwif_t
*, const struct ide_port_info
*);
1234 int ide_hwif_setup_dma(ide_hwif_t
*, const struct ide_port_info
*);
1236 static inline int ide_hwif_setup_dma(ide_hwif_t
*hwif
,
1237 const struct ide_port_info
*d
)
1243 typedef struct ide_pci_enablebit_s
{
1244 u8 reg
; /* byte pci reg holding the enable-bit */
1245 u8 mask
; /* mask to isolate the enable-bit */
1246 u8 val
; /* value of masked reg when "enabled" */
1247 } ide_pci_enablebit_t
;
1250 /* Uses ISA control ports not PCI ones. */
1251 IDE_HFLAG_ISA_PORTS
= (1 << 0),
1252 /* single port device */
1253 IDE_HFLAG_SINGLE
= (1 << 1),
1254 /* don't use legacy PIO blacklist */
1255 IDE_HFLAG_PIO_NO_BLACKLIST
= (1 << 2),
1256 /* set for the second port of QD65xx */
1257 IDE_HFLAG_QD_2ND_PORT
= (1 << 3),
1258 /* use PIO8/9 for prefetch off/on */
1259 IDE_HFLAG_ABUSE_PREFETCH
= (1 << 4),
1260 /* use PIO6/7 for fast-devsel off/on */
1261 IDE_HFLAG_ABUSE_FAST_DEVSEL
= (1 << 5),
1262 /* use 100-102 and 200-202 PIO values to set DMA modes */
1263 IDE_HFLAG_ABUSE_DMA_MODES
= (1 << 6),
1265 * keep DMA setting when programming PIO mode, may be used only
1266 * for hosts which have separate PIO and DMA timings (ie. PMAC)
1268 IDE_HFLAG_SET_PIO_MODE_KEEP_DMA
= (1 << 7),
1269 /* program host for the transfer mode after programming device */
1270 IDE_HFLAG_POST_SET_MODE
= (1 << 8),
1271 /* don't program host/device for the transfer mode ("smart" hosts) */
1272 IDE_HFLAG_NO_SET_MODE
= (1 << 9),
1273 /* trust BIOS for programming chipset/device for DMA */
1274 IDE_HFLAG_TRUST_BIOS_FOR_DMA
= (1 << 10),
1275 /* host is CS5510/CS5520 */
1276 IDE_HFLAG_CS5520
= (1 << 11),
1277 /* ATAPI DMA is unsupported */
1278 IDE_HFLAG_NO_ATAPI_DMA
= (1 << 12),
1279 /* set if host is a "non-bootable" controller */
1280 IDE_HFLAG_NON_BOOTABLE
= (1 << 13),
1281 /* host doesn't support DMA */
1282 IDE_HFLAG_NO_DMA
= (1 << 14),
1283 /* check if host is PCI IDE device before allowing DMA */
1284 IDE_HFLAG_NO_AUTODMA
= (1 << 15),
1285 /* host uses MMIO */
1286 IDE_HFLAG_MMIO
= (1 << 16),
1288 IDE_HFLAG_NO_LBA48
= (1 << 17),
1290 IDE_HFLAG_NO_LBA48_DMA
= (1 << 18),
1291 /* data FIFO is cleared by an error */
1292 IDE_HFLAG_ERROR_STOPS_FIFO
= (1 << 19),
1293 /* serialize ports */
1294 IDE_HFLAG_SERIALIZE
= (1 << 20),
1295 /* use legacy IRQs */
1296 IDE_HFLAG_LEGACY_IRQS
= (1 << 21),
1297 /* force use of legacy IRQs */
1298 IDE_HFLAG_FORCE_LEGACY_IRQS
= (1 << 22),
1299 /* limit LBA48 requests to 256 sectors */
1300 IDE_HFLAG_RQSIZE_256
= (1 << 23),
1301 /* use 32-bit I/O ops */
1302 IDE_HFLAG_IO_32BIT
= (1 << 24),
1304 IDE_HFLAG_UNMASK_IRQS
= (1 << 25),
1305 /* serialize ports if DMA is possible (for sl82c105) */
1306 IDE_HFLAG_SERIALIZE_DMA
= (1 << 27),
1307 /* force host out of "simplex" mode */
1308 IDE_HFLAG_CLEAR_SIMPLEX
= (1 << 28),
1309 /* DSC overlap is unsupported */
1310 IDE_HFLAG_NO_DSC
= (1 << 29),
1311 /* never use 32-bit I/O ops */
1312 IDE_HFLAG_NO_IO_32BIT
= (1 << 30),
1313 /* never unmask IRQs */
1314 IDE_HFLAG_NO_UNMASK_IRQS
= (1 << 31),
1317 #ifdef CONFIG_BLK_DEV_OFFBOARD
1318 # define IDE_HFLAG_OFF_BOARD 0
1320 # define IDE_HFLAG_OFF_BOARD IDE_HFLAG_NON_BOOTABLE
1323 struct ide_port_info
{
1325 unsigned int (*init_chipset
)(struct pci_dev
*);
1326 void (*init_iops
)(ide_hwif_t
*);
1327 void (*init_hwif
)(ide_hwif_t
*);
1328 int (*init_dma
)(ide_hwif_t
*,
1329 const struct ide_port_info
*);
1331 const struct ide_tp_ops
*tp_ops
;
1332 const struct ide_port_ops
*port_ops
;
1333 const struct ide_dma_ops
*dma_ops
;
1335 ide_pci_enablebit_t enablebits
[2];
1336 hwif_chipset_t chipset
;
1344 int ide_pci_init_one(struct pci_dev
*, const struct ide_port_info
*, void *);
1345 int ide_pci_init_two(struct pci_dev
*, struct pci_dev
*,
1346 const struct ide_port_info
*, void *);
1347 void ide_pci_remove(struct pci_dev
*);
1350 int ide_pci_suspend(struct pci_dev
*, pm_message_t
);
1351 int ide_pci_resume(struct pci_dev
*);
1353 #define ide_pci_suspend NULL
1354 #define ide_pci_resume NULL
1357 void ide_map_sg(ide_drive_t
*, struct request
*);
1358 void ide_init_sg_cmd(ide_drive_t
*, struct request
*);
1360 #define BAD_DMA_DRIVE 0
1361 #define GOOD_DMA_DRIVE 1
1363 struct drive_list_entry
{
1364 const char *id_model
;
1365 const char *id_firmware
;
1368 int ide_in_drive_list(u16
*, const struct drive_list_entry
*);
1370 #ifdef CONFIG_BLK_DEV_IDEDMA
1371 int __ide_dma_bad_drive(ide_drive_t
*);
1372 int ide_id_dma_bug(ide_drive_t
*);
1374 u8
ide_find_dma_mode(ide_drive_t
*, u8
);
1376 static inline u8
ide_max_dma_mode(ide_drive_t
*drive
)
1378 return ide_find_dma_mode(drive
, XFER_UDMA_6
);
1381 void ide_dma_off_quietly(ide_drive_t
*);
1382 void ide_dma_off(ide_drive_t
*);
1383 void ide_dma_on(ide_drive_t
*);
1384 int ide_set_dma(ide_drive_t
*);
1385 void ide_check_dma_crc(ide_drive_t
*);
1386 ide_startstop_t
ide_dma_intr(ide_drive_t
*);
1388 int ide_build_sglist(ide_drive_t
*, struct request
*);
1389 void ide_destroy_dmatable(ide_drive_t
*);
1391 #ifdef CONFIG_BLK_DEV_IDEDMA_SFF
1392 extern int ide_build_dmatable(ide_drive_t
*, struct request
*);
1393 int ide_allocate_dma_engine(ide_hwif_t
*);
1394 void ide_release_dma_engine(ide_hwif_t
*);
1396 void ide_dma_host_set(ide_drive_t
*, int);
1397 extern int ide_dma_setup(ide_drive_t
*);
1398 void ide_dma_exec_cmd(ide_drive_t
*, u8
);
1399 extern void ide_dma_start(ide_drive_t
*);
1400 extern int __ide_dma_end(ide_drive_t
*);
1401 int ide_dma_test_irq(ide_drive_t
*);
1402 extern void ide_dma_lost_irq(ide_drive_t
*);
1403 extern void ide_dma_timeout(ide_drive_t
*);
1404 extern const struct ide_dma_ops sff_dma_ops
;
1405 #endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
1408 static inline int ide_id_dma_bug(ide_drive_t
*drive
) { return 0; }
1409 static inline u8
ide_find_dma_mode(ide_drive_t
*drive
, u8 speed
) { return 0; }
1410 static inline u8
ide_max_dma_mode(ide_drive_t
*drive
) { return 0; }
1411 static inline void ide_dma_off_quietly(ide_drive_t
*drive
) { ; }
1412 static inline void ide_dma_off(ide_drive_t
*drive
) { ; }
1413 static inline void ide_dma_on(ide_drive_t
*drive
) { ; }
1414 static inline void ide_dma_verbose(ide_drive_t
*drive
) { ; }
1415 static inline int ide_set_dma(ide_drive_t
*drive
) { return 1; }
1416 static inline void ide_check_dma_crc(ide_drive_t
*drive
) { ; }
1417 #endif /* CONFIG_BLK_DEV_IDEDMA */
1419 #ifndef CONFIG_BLK_DEV_IDEDMA_SFF
1420 static inline void ide_release_dma_engine(ide_hwif_t
*hwif
) { ; }
1423 #ifdef CONFIG_BLK_DEV_IDEACPI
1424 extern int ide_acpi_exec_tfs(ide_drive_t
*drive
);
1425 extern void ide_acpi_get_timing(ide_hwif_t
*hwif
);
1426 extern void ide_acpi_push_timing(ide_hwif_t
*hwif
);
1427 extern void ide_acpi_init(ide_hwif_t
*hwif
);
1428 void ide_acpi_port_init_devices(ide_hwif_t
*);
1429 extern void ide_acpi_set_state(ide_hwif_t
*hwif
, int on
);
1431 static inline int ide_acpi_exec_tfs(ide_drive_t
*drive
) { return 0; }
1432 static inline void ide_acpi_get_timing(ide_hwif_t
*hwif
) { ; }
1433 static inline void ide_acpi_push_timing(ide_hwif_t
*hwif
) { ; }
1434 static inline void ide_acpi_init(ide_hwif_t
*hwif
) { ; }
1435 static inline void ide_acpi_port_init_devices(ide_hwif_t
*hwif
) { ; }
1436 static inline void ide_acpi_set_state(ide_hwif_t
*hwif
, int on
) {}
1439 void ide_remove_port_from_hwgroup(ide_hwif_t
*);
1440 void ide_unregister(ide_hwif_t
*);
1442 void ide_register_region(struct gendisk
*);
1443 void ide_unregister_region(struct gendisk
*);
1445 void ide_undecoded_slave(ide_drive_t
*);
1447 void ide_port_apply_params(ide_hwif_t
*);
1449 struct ide_host
*ide_host_alloc_all(const struct ide_port_info
*, hw_regs_t
**);
1450 struct ide_host
*ide_host_alloc(const struct ide_port_info
*, hw_regs_t
**);
1451 void ide_host_free(struct ide_host
*);
1452 int ide_host_register(struct ide_host
*, const struct ide_port_info
*,
1454 int ide_host_add(const struct ide_port_info
*, hw_regs_t
**,
1455 struct ide_host
**);
1456 void ide_host_remove(struct ide_host
*);
1457 int ide_legacy_device_add(const struct ide_port_info
*, unsigned long);
1458 void ide_port_unregister_devices(ide_hwif_t
*);
1459 void ide_port_scan(ide_hwif_t
*);
1461 static inline void *ide_get_hwifdata (ide_hwif_t
* hwif
)
1463 return hwif
->hwif_data
;
1466 static inline void ide_set_hwifdata (ide_hwif_t
* hwif
, void *data
)
1468 hwif
->hwif_data
= data
;
1471 const char *ide_xfer_verbose(u8 mode
);
1472 extern void ide_toggle_bounce(ide_drive_t
*drive
, int on
);
1473 extern int ide_set_xfer_rate(ide_drive_t
*drive
, u8 rate
);
1475 u64
ide_get_lba_addr(struct ide_taskfile
*, int);
1476 u8
ide_dump_status(ide_drive_t
*, const char *, u8
);
1481 u16 act8b
; /* t2 for 8-bit io */
1482 u16 rec8b
; /* t2i for 8-bit io */
1483 u16 cyc8b
; /* t0 for 8-bit io */
1484 u16 active
; /* t2 or tD */
1485 u16 recover
; /* t2i or tK */
1487 u16 udma
; /* t2CYCTYP/2 */
1491 IDE_TIMING_SETUP
= (1 << 0),
1492 IDE_TIMING_ACT8B
= (1 << 1),
1493 IDE_TIMING_REC8B
= (1 << 2),
1494 IDE_TIMING_CYC8B
= (1 << 3),
1495 IDE_TIMING_8BIT
= IDE_TIMING_ACT8B
| IDE_TIMING_REC8B
|
1497 IDE_TIMING_ACTIVE
= (1 << 4),
1498 IDE_TIMING_RECOVER
= (1 << 5),
1499 IDE_TIMING_CYCLE
= (1 << 6),
1500 IDE_TIMING_UDMA
= (1 << 7),
1501 IDE_TIMING_ALL
= IDE_TIMING_SETUP
| IDE_TIMING_8BIT
|
1502 IDE_TIMING_ACTIVE
| IDE_TIMING_RECOVER
|
1503 IDE_TIMING_CYCLE
| IDE_TIMING_UDMA
,
1506 struct ide_timing
*ide_timing_find_mode(u8
);
1507 u16
ide_pio_cycle_time(ide_drive_t
*, u8
);
1508 void ide_timing_merge(struct ide_timing
*, struct ide_timing
*,
1509 struct ide_timing
*, unsigned int);
1510 int ide_timing_compute(ide_drive_t
*, u8
, struct ide_timing
*, int, int);
1512 int ide_scan_pio_blacklist(char *);
1514 u8
ide_get_best_pio_mode(ide_drive_t
*, u8
, u8
);
1516 int ide_set_pio_mode(ide_drive_t
*, u8
);
1517 int ide_set_dma_mode(ide_drive_t
*, u8
);
1519 void ide_set_pio(ide_drive_t
*, u8
);
1521 static inline void ide_set_max_pio(ide_drive_t
*drive
)
1523 ide_set_pio(drive
, 255);
1526 extern spinlock_t ide_lock
;
1527 extern struct mutex ide_cfg_mtx
;
1529 * Structure locking:
1531 * ide_cfg_mtx and ide_lock together protect changes to
1532 * ide_hwif_t->{next,hwgroup}
1535 * ide_hwgroup_t->busy: ide_lock
1536 * ide_hwgroup_t->hwif: ide_lock
1537 * ide_hwif_t->mate: constant, no locking
1538 * ide_drive_t->hwif: constant, no locking
1541 #define local_irq_set(flags) do { local_save_flags((flags)); local_irq_enable_in_hardirq(); } while (0)
1543 extern struct bus_type ide_bus_type
;
1544 extern struct class *ide_port_class
;
1546 static inline void ide_dump_identify(u8
*id
)
1548 print_hex_dump(KERN_INFO
, "", DUMP_PREFIX_NONE
, 16, 2, id
, 512, 0);
1551 static inline int hwif_to_node(ide_hwif_t
*hwif
)
1553 return hwif
->dev
? dev_to_node(hwif
->dev
) : -1;
1556 static inline ide_drive_t
*ide_get_pair_dev(ide_drive_t
*drive
)
1558 ide_drive_t
*peer
= &drive
->hwif
->drives
[(drive
->dn
^ 1) & 1];
1560 return peer
->present
? peer
: NULL
;