include/asm-mips/sn/sn0/addrs.h

   1 /*
   2  * This file is subject to the terms and conditions of the GNU General Public
   3  * License.  See the file "COPYING" in the main directory of this archive
   4  * for more details.
   5  *
   6  * Derived from IRIX <sys/SN/SN0/addrs.h>, revision 1.126.
   7  *
   8  * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc.
   9  * Copyright (C) 1999 by Ralf Baechle
  10  */
  11 #ifndef _ASM_SN_SN0_ADDRS_H
  12 #define _ASM_SN_SN0_ADDRS_H
  13
  14
  15 /*
  16  * SN0 (on a T5) Address map
  17  *
  18  * This file contains a set of definitions and macros which are used
  19  * to reference into the major address spaces (CAC, HSPEC, IO, MSPEC,
  20  * and UNCAC) used by the SN0 architecture.  It also contains addresses
  21  * for "major" statically locatable PROM/Kernel data structures, such as
  22  * the partition table, the configuration data structure, etc.
  23  * We make an implicit assumption that the processor using this file
  24  * follows the R10K's provisions for specifying uncached attributes;
  25  * should this change, the base registers may very well become processor-
  26  * dependent.
  27  *
  28  * For more information on the address spaces, see the "Local Resources"
  29  * chapter of the Hub specification.
  30  *
  31  * NOTE: This header file is included both by C and by assembler source
  32  *       files.  Please bracket any language-dependent definitions
  33  *       appropriately.
  34  */
  35
  36 /*
  37  * Some of the macros here need to be casted to appropriate types when used
  38  * from C.  They definitely must not be casted from assembly language so we
  39  * use some new ANSI preprocessor stuff to paste these on where needed.
  40  */
  41
  42 /*
  43  * The following couple of definitions will eventually need to be variables,
  44  * since the amount of address space assigned to each node depends on
  45  * whether the system is running in N-mode (more nodes with less memory)
  46  * or M-mode (fewer nodes with more memory).  We expect that it will
  47  * be a while before we need to make this decision dynamically, though,
  48  * so for now we just use defines bracketed by an ifdef.
  49  */
  50
  51 #ifdef CONFIG_SGI_SN0_N_MODE
  52
  53 #define NODE_SIZE_BITS          31
  54 #define BWIN_SIZE_BITS          28
  55
  56 #define NASID_BITS              9
  57 #define NASID_BITMASK           (0x1ffLL)
  58 #define NASID_SHFT              31
  59 #define NASID_META_BITS         5
  60 #define NASID_LOCAL_BITS        4
  61
  62 #define BDDIR_UPPER_MASK        (UINT64_CAST 0x7ffff << 10)
  63 #define BDECC_UPPER_MASK        (UINT64_CAST 0x3ffffff << 3)
  64
  65 #else /* !defined(CONFIG_SGI_SN0_N_MODE), assume that M-mode is desired */
  66
  67 #define NODE_SIZE_BITS          32
  68 #define BWIN_SIZE_BITS          29
  69
  70 #define NASID_BITMASK           (0xffLL)
  71 #define NASID_BITS              8
  72 #define NASID_SHFT              32
  73 #define NASID_META_BITS         4
  74 #define NASID_LOCAL_BITS        4
  75
  76 #define BDDIR_UPPER_MASK        (UINT64_CAST 0xfffff << 10)
  77 #define BDECC_UPPER_MASK        (UINT64_CAST 0x7ffffff << 3)
  78
  79 #endif /* !defined(CONFIG_SGI_SN0_N_MODE) */
  80
  81 #define NODE_ADDRSPACE_SIZE     (UINT64_CAST 1 << NODE_SIZE_BITS)
  82
  83 #define NASID_MASK              (UINT64_CAST NASID_BITMASK << NASID_SHFT)
  84 #define NASID_GET(_pa)          (int) ((UINT64_CAST (_pa) >>            \
  85                                         NASID_SHFT) & NASID_BITMASK)
  86
  87 #if !defined(__ASSEMBLY__) && !defined(_STANDALONE)
  88
  89 #define NODE_SWIN_BASE(nasid, widget)                                   \
  90         ((widget == 0) ? NODE_BWIN_BASE((nasid), SWIN0_BIGWIN)          \
  91         : RAW_NODE_SWIN_BASE(nasid, widget))
  92 #else /* __ASSEMBLY__ || _STANDALONE */
  93 #define NODE_SWIN_BASE(nasid, widget) \
  94      (NODE_IO_BASE(nasid) + (UINT64_CAST (widget) << SWIN_SIZE_BITS))
  95 #endif /* __ASSEMBLY__ || _STANDALONE */
  96
  97 /*
  98  * The following definitions pertain to the IO special address
  99  * space.  They define the location of the big and little windows
 100  * of any given node.
 101  */
 102
 103 #define BWIN_INDEX_BITS         3
 104 #define BWIN_SIZE               (UINT64_CAST 1 << BWIN_SIZE_BITS)
 105 #define BWIN_SIZEMASK           (BWIN_SIZE - 1)
 106 #define BWIN_WIDGET_MASK        0x7
 107 #define NODE_BWIN_BASE0(nasid)  (NODE_IO_BASE(nasid) + BWIN_SIZE)
 108 #define NODE_BWIN_BASE(nasid, bigwin)   (NODE_BWIN_BASE0(nasid) +       \
 109                         (UINT64_CAST (bigwin) << BWIN_SIZE_BITS))
 110
 111 #define BWIN_WIDGETADDR(addr)   ((addr) & BWIN_SIZEMASK)
 112 #define BWIN_WINDOWNUM(addr)    (((addr) >> BWIN_SIZE_BITS) & BWIN_WIDGET_MASK)
 113 /*
 114  * Verify if addr belongs to large window address of node with "nasid"
 115  *
 116  *
 117  * NOTE: "addr" is expected to be XKPHYS address, and NOT physical
 118  * address
 119  *
 120  *
 121  */
 122
 123 #define NODE_BWIN_ADDR(nasid, addr)     \
 124                 (((addr) >= NODE_BWIN_BASE0(nasid)) && \
 125                  ((addr) < (NODE_BWIN_BASE(nasid, HUB_NUM_BIG_WINDOW) + \
 126                                 BWIN_SIZE)))
 127
 128 /*
 129  * The following define the major position-independent aliases used
 130  * in SN0.
 131  *      CALIAS -- Varies in size, points to the first n bytes of memory
 132  *                      on the reader's node.
 133  */
 134
 135 #define CALIAS_BASE             CAC_BASE
 136
 137
 138
 139 #define BRIDGE_REG_PTR(_base, _off)     ((volatile bridgereg_t *) \
 140         ((__psunsigned_t)(_base) + (__psunsigned_t)(_off)))
 141
 142 #define SN0_WIDGET_BASE(_nasid, _wid)   (NODE_SWIN_BASE((_nasid), (_wid)))
 143
 144 /* Turn on sable logging for the processors whose bits are set. */
 145 #ifdef SABLE
 146 #define SABLE_LOG_TRIGGER(_map) \
 147                 *((volatile hubreg_t *)(IO_BASE + 0x17ffff0)) = (_map)
 148 #else
 149 #define SABLE_LOG_TRIGGER(_map)
 150 #endif /* SABLE */
 151
 152 #ifndef __ASSEMBLY__
 153 #define KERN_NMI_ADDR(nasid, slice)                                     \
 154                     TO_NODE_UNCAC((nasid), IP27_NMI_KREGS_OFFSET +      \
 155                                   (IP27_NMI_KREGS_CPU_SIZE * (slice)))
 156 #endif /* !__ASSEMBLY__ */
 157
 158 #ifdef PROM
 159
 160 #define MISC_PROM_BASE          PHYS_TO_K0(0x01300000)
 161 #define MISC_PROM_SIZE          0x200000
 162
 163 #define DIAG_BASE               PHYS_TO_K0(0x01500000)
 164 #define DIAG_SIZE               0x300000
 165
 166 #define ROUTE_BASE              PHYS_TO_K0(0x01800000)
 167 #define ROUTE_SIZE              0x200000
 168
 169 #define IP27PROM_FLASH_HDR      PHYS_TO_K0(0x01300000)
 170 #define IP27PROM_FLASH_DATA     PHYS_TO_K0(0x01301000)
 171 #define IP27PROM_CORP_MAX       32
 172 #define IP27PROM_CORP           PHYS_TO_K0(0x01800000)
 173 #define IP27PROM_CORP_SIZE      0x10000
 174 #define IP27PROM_CORP_STK       PHYS_TO_K0(0x01810000)
 175 #define IP27PROM_CORP_STKSIZE   0x2000
 176 #define IP27PROM_DECOMP_BUF     PHYS_TO_K0(0x01900000)
 177 #define IP27PROM_DECOMP_SIZE    0xfff00
 178
 179 #define IP27PROM_BASE           PHYS_TO_K0(0x01a00000)
 180 #define IP27PROM_BASE_MAPPED    (UNCAC_BASE | 0x1fc00000)
 181 #define IP27PROM_SIZE_MAX       0x100000
 182
 183 #define IP27PROM_PCFG           PHYS_TO_K0(0x01b00000)
 184 #define IP27PROM_PCFG_SIZE      0xd0000
 185 #define IP27PROM_ERRDMP         PHYS_TO_K1(0x01bd0000)
 186 #define IP27PROM_ERRDMP_SIZE    0xf000
 187
 188 #define IP27PROM_INIT_START     PHYS_TO_K1(0x01bd0000)
 189 #define IP27PROM_CONSOLE        PHYS_TO_K1(0x01bdf000)
 190 #define IP27PROM_CONSOLE_SIZE   0x200
 191 #define IP27PROM_NETUART        PHYS_TO_K1(0x01bdf200)
 192 #define IP27PROM_NETUART_SIZE   0x100
 193 #define IP27PROM_UNUSED1        PHYS_TO_K1(0x01bdf300)
 194 #define IP27PROM_UNUSED1_SIZE   0x500
 195 #define IP27PROM_ELSC_BASE_A    PHYS_TO_K0(0x01bdf800)
 196 #define IP27PROM_ELSC_BASE_B    PHYS_TO_K0(0x01bdfc00)
 197 #define IP27PROM_STACK_A        PHYS_TO_K0(0x01be0000)
 198 #define IP27PROM_STACK_B        PHYS_TO_K0(0x01bf0000)
 199 #define IP27PROM_STACK_SHFT     16
 200 #define IP27PROM_STACK_SIZE     (1 << IP27PROM_STACK_SHFT)
 201 #define IP27PROM_INIT_END       PHYS_TO_K0(0x01c00000)
 202
 203 #define SLAVESTACK_BASE         PHYS_TO_K0(0x01580000)
 204 #define SLAVESTACK_SIZE         0x40000
 205
 206 #define ENETBUFS_BASE           PHYS_TO_K0(0x01f80000)
 207 #define ENETBUFS_SIZE           0x20000
 208
 209 #define IO6PROM_BASE            PHYS_TO_K0(0x01c00000)
 210 #define IO6PROM_SIZE            0x400000
 211 #define IO6PROM_BASE_MAPPED     (UNCAC_BASE | 0x11c00000)
 212 #define IO6DPROM_BASE           PHYS_TO_K0(0x01c00000)
 213 #define IO6DPROM_SIZE           0x200000
 214
 215 #define NODEBUGUNIX_ADDR        PHYS_TO_K0(0x00019000)
 216 #define DEBUGUNIX_ADDR          PHYS_TO_K0(0x00100000)
 217
 218 #define IP27PROM_INT_LAUNCH     10      /* and 11 */
 219 #define IP27PROM_INT_NETUART    12      /* through 17 */
 220
 221 #endif /* PROM */
 222
 223 /*
 224  * needed by symmon so it needs to be outside #if PROM
 225  */
 226 #define IP27PROM_ELSC_SHFT      10
 227 #define IP27PROM_ELSC_SIZE      (1 << IP27PROM_ELSC_SHFT)
 228
 229 /*
 230  * This address is used by IO6PROM to build MemoryDescriptors of
 231  * free memory. This address is important since unix gets loaded
 232  * at this address, and this memory has to be FREE if unix is to
 233  * be loaded.
 234  */
 235
 236 #define FREEMEM_BASE            PHYS_TO_K0(0x2000000)
 237
 238 #define IO6PROM_STACK_SHFT      14      /* stack per cpu */
 239 #define IO6PROM_STACK_SIZE      (1 << IO6PROM_STACK_SHFT)
 240
 241 /*
 242  * IP27 PROM vectors
 243  */
 244
 245 #define IP27PROM_ENTRY          PHYS_TO_COMPATK1(0x1fc00000)
 246 #define IP27PROM_RESTART        PHYS_TO_COMPATK1(0x1fc00008)
 247 #define IP27PROM_SLAVELOOP      PHYS_TO_COMPATK1(0x1fc00010)
 248 #define IP27PROM_PODMODE        PHYS_TO_COMPATK1(0x1fc00018)
 249 #define IP27PROM_IOC3UARTPOD    PHYS_TO_COMPATK1(0x1fc00020)
 250 #define IP27PROM_FLASHLEDS      PHYS_TO_COMPATK1(0x1fc00028)
 251 #define IP27PROM_REPOD          PHYS_TO_COMPATK1(0x1fc00030)
 252 #define IP27PROM_LAUNCHSLAVE    PHYS_TO_COMPATK1(0x1fc00038)
 253 #define IP27PROM_WAITSLAVE      PHYS_TO_COMPATK1(0x1fc00040)
 254 #define IP27PROM_POLLSLAVE      PHYS_TO_COMPATK1(0x1fc00048)
 255
 256 #define KL_UART_BASE    LOCAL_HUB_ADDR(MD_UREG0_0)      /* base of UART regs */
 257 #define KL_UART_CMD     LOCAL_HUB_ADDR(MD_UREG0_0)      /* UART command reg */
 258 #define KL_UART_DATA    LOCAL_HUB_ADDR(MD_UREG0_1)      /* UART data reg */
 259 #define KL_I2C_REG      MD_UREG0_0                      /* I2C reg */
 260
 261 #ifndef __ASSEMBLY__
 262
 263 /* Address 0x400 to 0x1000 ualias points to cache error eframe + misc
 264  * CACHE_ERR_SP_PTR could either contain an address to the stack, or
 265  * the stack could start at CACHE_ERR_SP_PTR
 266  */
 267 #if defined (HUB_ERR_STS_WAR)
 268 #define CACHE_ERR_EFRAME        0x480
 269 #else /* HUB_ERR_STS_WAR */
 270 #define CACHE_ERR_EFRAME        0x400
 271 #endif /* HUB_ERR_STS_WAR */
 272
 273 #define CACHE_ERR_ECCFRAME      (CACHE_ERR_EFRAME + EF_SIZE)
 274 #define CACHE_ERR_SP_PTR        (0x1000 - 32)   /* why -32? TBD */
 275 #define CACHE_ERR_IBASE_PTR     (0x1000 - 40)
 276 #define CACHE_ERR_SP            (CACHE_ERR_SP_PTR - 16)
 277 #define CACHE_ERR_AREA_SIZE     (ARCS_SPB_OFFSET - CACHE_ERR_EFRAME)
 278
 279 #endif  /* !__ASSEMBLY__ */
 280
 281 #define _ARCSPROM
 282
 283 #ifdef _STANDALONE
 284
 285 /*
 286  * The PROM needs to pass the device base address and the
 287  * device pci cfg space address to the device drivers during
 288  * install. The COMPONENT->Key field is used for this purpose.
 289  * Macros needed by SN0 device drivers to convert the
 290  * COMPONENT->Key field to the respective base address.
 291  * Key field looks as follows:
 292  *
 293  *  +----------------------------------------------------+
 294  *  |devnasid | widget  |pciid |hubwidid|hstnasid | adap |
 295  *  |   2     |   1     |  1   |   1    |    2    |   1  |
 296  *  +----------------------------------------------------+
 297  *  |         |         |      |        |         |      |
 298  *  64        48        40     32       24        8      0
 299  *
 300  * These are used by standalone drivers till the io infrastructure
 301  * is in place.
 302  */
 303
 304 #ifndef __ASSEMBLY__
 305
 306 #define uchar unsigned char
 307
 308 #define KEY_DEVNASID_SHFT  48
 309 #define KEY_WIDID_SHFT     40
 310 #define KEY_PCIID_SHFT     32
 311 #define KEY_HUBWID_SHFT    24
 312 #define KEY_HSTNASID_SHFT  8
 313
 314 #define MK_SN0_KEY(nasid, widid, pciid) \
 315                         ((((__psunsigned_t)nasid)<< KEY_DEVNASID_SHFT |\
 316                                 ((__psunsigned_t)widid) << KEY_WIDID_SHFT) |\
 317                                 ((__psunsigned_t)pciid) << KEY_PCIID_SHFT)
 318
 319 #define ADD_HUBWID_KEY(key,hubwid)\
 320                         (key|=((__psunsigned_t)hubwid << KEY_HUBWID_SHFT))
 321
 322 #define ADD_HSTNASID_KEY(key,hstnasid)\
 323                         (key|=((__psunsigned_t)hstnasid << KEY_HSTNASID_SHFT))
 324
 325 #define GET_DEVNASID_FROM_KEY(key)      ((short)(key >> KEY_DEVNASID_SHFT))
 326 #define GET_WIDID_FROM_KEY(key)         ((uchar)(key >> KEY_WIDID_SHFT))
 327 #define GET_PCIID_FROM_KEY(key)         ((uchar)(key >> KEY_PCIID_SHFT))
 328 #define GET_HUBWID_FROM_KEY(key)        ((uchar)(key >> KEY_HUBWID_SHFT))
 329 #define GET_HSTNASID_FROM_KEY(key)      ((short)(key >> KEY_HSTNASID_SHFT))
 330
 331 #define PCI_64_TARGID_SHFT              60
 332
 333 #define GET_PCIBASE_FROM_KEY(key)  (NODE_SWIN_BASE(GET_DEVNASID_FROM_KEY(key),\
 334                                         GET_WIDID_FROM_KEY(key))\
 335                                         | BRIDGE_DEVIO(GET_PCIID_FROM_KEY(key)))
 336
 337 #define GET_PCICFGBASE_FROM_KEY(key) \
 338                         (NODE_SWIN_BASE(GET_DEVNASID_FROM_KEY(key),\
 339                               GET_WIDID_FROM_KEY(key))\
 340                         | BRIDGE_TYPE0_CFG_DEV(GET_PCIID_FROM_KEY(key)))
 341
 342 #define GET_WIDBASE_FROM_KEY(key) \
 343                         (NODE_SWIN_BASE(GET_DEVNASID_FROM_KEY(key),\
 344                               GET_WIDID_FROM_KEY(key)))
 345
 346 #define PUT_INSTALL_STATUS(c,s)         c->Revision = s
 347 #define GET_INSTALL_STATUS(c)           c->Revision
 348
 349 #endif /* !__ASSEMBLY__ */
 350
 351 #endif /* _STANDALONE */
 352
 353 #if defined (HUB_ERR_STS_WAR)
 354
 355 #define ERR_STS_WAR_REGISTER    IIO_IIBUSERR
 356 #define ERR_STS_WAR_ADDR        LOCAL_HUB_ADDR(IIO_IIBUSERR)
 357 #define ERR_STS_WAR_PHYSADDR    TO_PHYS((__psunsigned_t)ERR_STS_WAR_ADDR)
 358                                 /* Used to match addr in error reg. */
 359 #define OLD_ERR_STS_WAR_OFFSET  ((MD_MEM_BANKS * MD_BANK_SIZE) - 0x100)
 360
 361 #endif /* HUB_ERR_STS_WAR */
 362
 363 #endif /* _ASM_SN_SN0_ADDRS_H */