2 * Definitions for the new Marvell Yukon / SysKonenct driver.
7 /* PCI config registers */
8 #define PCI_DEV_REG1 0x40
9 #define PCI_PHY_COMA 0x8000000
10 #define PCI_VIO 0x2000000
11 #define PCI_DEV_REG2 0x44
12 #define PCI_REV_DESC 0x4
14 #define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
15 PCI_STATUS_SIG_SYSTEM_ERROR | \
16 PCI_STATUS_REC_MASTER_ABORT | \
17 PCI_STATUS_REC_TARGET_ABORT | \
24 B0_POWER_CTRL
= 0x0007,
32 B0_XM1_PHY_ADDR
= 0x0030,
33 B0_XM1_PHY_DATA
= 0x0034,
36 B0_XM2_PHY_ADDR
= 0x0050,
37 B0_XM2_PHY_DATA
= 0x0054,
66 B2_IRQM_CTRL
= 0x0148,
67 B2_IRQM_TEST
= 0x0149,
69 B2_IRQM_HWE_MSK
= 0x0150,
70 B2_TST_CTRL1
= 0x0158,
71 B2_TST_CTRL2
= 0x0159,
84 B3_RAM_DATA_LO
= 0x0184,
85 B3_RAM_DATA_HI
= 0x0188,
86 B3_RI_WTO_R1
= 0x0190,
87 B3_RI_WTO_XA1
= 0x0191,
88 B3_RI_WTO_XS1
= 0x0192,
89 B3_RI_RTO_R1
= 0x0193,
90 B3_RI_RTO_XA1
= 0x0194,
91 B3_RI_RTO_XS1
= 0x0195,
92 B3_RI_WTO_R2
= 0x0196,
93 B3_RI_WTO_XA2
= 0x0197,
94 B3_RI_WTO_XS2
= 0x0198,
95 B3_RI_RTO_R2
= 0x0199,
96 B3_RI_RTO_XA2
= 0x019a,
97 B3_RI_RTO_XS2
= 0x019b,
98 B3_RI_TO_VAL
= 0x019c,
101 B3_MA_TOINI_RX1
= 0x01b0,
102 B3_MA_TOINI_RX2
= 0x01b1,
103 B3_MA_TOINI_TX1
= 0x01b2,
104 B3_MA_TOINI_TX2
= 0x01b3,
105 B3_MA_TOVAL_RX1
= 0x01b4,
106 B3_MA_TOVAL_RX2
= 0x01b5,
107 B3_MA_TOVAL_TX1
= 0x01b6,
108 B3_MA_TOVAL_TX2
= 0x01b7,
109 B3_MA_TO_CTRL
= 0x01b8,
110 B3_MA_TO_TEST
= 0x01ba,
111 B3_MA_RCINI_RX1
= 0x01c0,
112 B3_MA_RCINI_RX2
= 0x01c1,
113 B3_MA_RCINI_TX1
= 0x01c2,
114 B3_MA_RCINI_TX2
= 0x01c3,
115 B3_MA_RCVAL_RX1
= 0x01c4,
116 B3_MA_RCVAL_RX2
= 0x01c5,
117 B3_MA_RCVAL_TX1
= 0x01c6,
118 B3_MA_RCVAL_TX2
= 0x01c7,
119 B3_MA_RC_CTRL
= 0x01c8,
120 B3_MA_RC_TEST
= 0x01ca,
121 B3_PA_TOINI_RX1
= 0x01d0,
122 B3_PA_TOINI_RX2
= 0x01d4,
123 B3_PA_TOINI_TX1
= 0x01d8,
124 B3_PA_TOINI_TX2
= 0x01dc,
125 B3_PA_TOVAL_RX1
= 0x01e0,
126 B3_PA_TOVAL_RX2
= 0x01e4,
127 B3_PA_TOVAL_TX1
= 0x01e8,
128 B3_PA_TOVAL_TX2
= 0x01ec,
133 /* B0_CTST 16 bit Control/Status register */
135 CS_CLK_RUN_HOT
= 1<<13,/* CLK_RUN hot m. (YUKON-Lite only) */
136 CS_CLK_RUN_RST
= 1<<12,/* CLK_RUN reset (YUKON-Lite only) */
137 CS_CLK_RUN_ENA
= 1<<11,/* CLK_RUN enable (YUKON-Lite only) */
138 CS_VAUX_AVAIL
= 1<<10,/* VAUX available (YUKON only) */
139 CS_BUS_CLOCK
= 1<<9, /* Bus Clock 0/1 = 33/66 MHz */
140 CS_BUS_SLOT_SZ
= 1<<8, /* Slot Size 0/1 = 32/64 bit slot */
141 CS_ST_SW_IRQ
= 1<<7, /* Set IRQ SW Request */
142 CS_CL_SW_IRQ
= 1<<6, /* Clear IRQ SW Request */
143 CS_STOP_DONE
= 1<<5, /* Stop Master is finished */
144 CS_STOP_MAST
= 1<<4, /* Command Bit to stop the master */
145 CS_MRST_CLR
= 1<<3, /* Clear Master reset */
146 CS_MRST_SET
= 1<<2, /* Set Master reset */
147 CS_RST_CLR
= 1<<1, /* Clear Software reset */
148 CS_RST_SET
= 1, /* Set Software reset */
150 /* B0_LED 8 Bit LED register */
151 /* Bit 7.. 2: reserved */
152 LED_STAT_ON
= 1<<1, /* Status LED on */
153 LED_STAT_OFF
= 1, /* Status LED off */
155 /* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */
156 PC_VAUX_ENA
= 1<<7, /* Switch VAUX Enable */
157 PC_VAUX_DIS
= 1<<6, /* Switch VAUX Disable */
158 PC_VCC_ENA
= 1<<5, /* Switch VCC Enable */
159 PC_VCC_DIS
= 1<<4, /* Switch VCC Disable */
160 PC_VAUX_ON
= 1<<3, /* Switch VAUX On */
161 PC_VAUX_OFF
= 1<<2, /* Switch VAUX Off */
162 PC_VCC_ON
= 1<<1, /* Switch VCC On */
163 PC_VCC_OFF
= 1<<0, /* Switch VCC Off */
166 /* B2_IRQM_MSK 32 bit IRQ Moderation Mask */
168 IS_ALL_MSK
= 0xbffffffful
, /* All Interrupt bits */
169 IS_HW_ERR
= 1<<31, /* Interrupt HW Error */
170 /* Bit 30: reserved */
171 IS_PA_TO_RX1
= 1<<29, /* Packet Arb Timeout Rx1 */
172 IS_PA_TO_RX2
= 1<<28, /* Packet Arb Timeout Rx2 */
173 IS_PA_TO_TX1
= 1<<27, /* Packet Arb Timeout Tx1 */
174 IS_PA_TO_TX2
= 1<<26, /* Packet Arb Timeout Tx2 */
175 IS_I2C_READY
= 1<<25, /* IRQ on end of I2C Tx */
176 IS_IRQ_SW
= 1<<24, /* SW forced IRQ */
177 IS_EXT_REG
= 1<<23, /* IRQ from LM80 or PHY (GENESIS only) */
178 /* IRQ from PHY (YUKON only) */
179 IS_TIMINT
= 1<<22, /* IRQ from Timer */
180 IS_MAC1
= 1<<21, /* IRQ from MAC 1 */
181 IS_LNK_SYNC_M1
= 1<<20, /* Link Sync Cnt wrap MAC 1 */
182 IS_MAC2
= 1<<19, /* IRQ from MAC 2 */
183 IS_LNK_SYNC_M2
= 1<<18, /* Link Sync Cnt wrap MAC 2 */
184 /* Receive Queue 1 */
185 IS_R1_B
= 1<<17, /* Q_R1 End of Buffer */
186 IS_R1_F
= 1<<16, /* Q_R1 End of Frame */
187 IS_R1_C
= 1<<15, /* Q_R1 Encoding Error */
188 /* Receive Queue 2 */
189 IS_R2_B
= 1<<14, /* Q_R2 End of Buffer */
190 IS_R2_F
= 1<<13, /* Q_R2 End of Frame */
191 IS_R2_C
= 1<<12, /* Q_R2 Encoding Error */
192 /* Synchronous Transmit Queue 1 */
193 IS_XS1_B
= 1<<11, /* Q_XS1 End of Buffer */
194 IS_XS1_F
= 1<<10, /* Q_XS1 End of Frame */
195 IS_XS1_C
= 1<<9, /* Q_XS1 Encoding Error */
196 /* Asynchronous Transmit Queue 1 */
197 IS_XA1_B
= 1<<8, /* Q_XA1 End of Buffer */
198 IS_XA1_F
= 1<<7, /* Q_XA1 End of Frame */
199 IS_XA1_C
= 1<<6, /* Q_XA1 Encoding Error */
200 /* Synchronous Transmit Queue 2 */
201 IS_XS2_B
= 1<<5, /* Q_XS2 End of Buffer */
202 IS_XS2_F
= 1<<4, /* Q_XS2 End of Frame */
203 IS_XS2_C
= 1<<3, /* Q_XS2 Encoding Error */
204 /* Asynchronous Transmit Queue 2 */
205 IS_XA2_B
= 1<<2, /* Q_XA2 End of Buffer */
206 IS_XA2_F
= 1<<1, /* Q_XA2 End of Frame */
207 IS_XA2_C
= 1<<0, /* Q_XA2 Encoding Error */
209 IS_TO_PORT1
= IS_PA_TO_RX1
| IS_PA_TO_TX1
,
210 IS_TO_PORT2
= IS_PA_TO_RX2
| IS_PA_TO_TX2
,
212 IS_PORT_1
= IS_XA1_F
| IS_R1_F
| IS_TO_PORT1
| IS_MAC1
,
213 IS_PORT_2
= IS_XA2_F
| IS_R2_F
| IS_TO_PORT2
| IS_MAC2
,
217 /* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
219 IS_IRQ_TIST_OV
= 1<<13, /* Time Stamp Timer Overflow (YUKON only) */
220 IS_IRQ_SENSOR
= 1<<12, /* IRQ from Sensor (YUKON only) */
221 IS_IRQ_MST_ERR
= 1<<11, /* IRQ master error detected */
222 IS_IRQ_STAT
= 1<<10, /* IRQ status exception */
223 IS_NO_STAT_M1
= 1<<9, /* No Rx Status from MAC 1 */
224 IS_NO_STAT_M2
= 1<<8, /* No Rx Status from MAC 2 */
225 IS_NO_TIST_M1
= 1<<7, /* No Time Stamp from MAC 1 */
226 IS_NO_TIST_M2
= 1<<6, /* No Time Stamp from MAC 2 */
227 IS_RAM_RD_PAR
= 1<<5, /* RAM Read Parity Error */
228 IS_RAM_WR_PAR
= 1<<4, /* RAM Write Parity Error */
229 IS_M1_PAR_ERR
= 1<<3, /* MAC 1 Parity Error */
230 IS_M2_PAR_ERR
= 1<<2, /* MAC 2 Parity Error */
231 IS_R1_PAR_ERR
= 1<<1, /* Queue R1 Parity Error */
232 IS_R2_PAR_ERR
= 1<<0, /* Queue R2 Parity Error */
234 IS_ERR_MSK
= IS_IRQ_MST_ERR
| IS_IRQ_STAT
235 | IS_NO_STAT_M1
| IS_NO_STAT_M2
236 | IS_RAM_RD_PAR
| IS_RAM_WR_PAR
237 | IS_M1_PAR_ERR
| IS_M2_PAR_ERR
238 | IS_R1_PAR_ERR
| IS_R2_PAR_ERR
,
241 /* B2_TST_CTRL1 8 bit Test Control Register 1 */
243 TST_FRC_DPERR_MR
= 1<<7, /* force DATAPERR on MST RD */
244 TST_FRC_DPERR_MW
= 1<<6, /* force DATAPERR on MST WR */
245 TST_FRC_DPERR_TR
= 1<<5, /* force DATAPERR on TRG RD */
246 TST_FRC_DPERR_TW
= 1<<4, /* force DATAPERR on TRG WR */
247 TST_FRC_APERR_M
= 1<<3, /* force ADDRPERR on MST */
248 TST_FRC_APERR_T
= 1<<2, /* force ADDRPERR on TRG */
249 TST_CFG_WRITE_ON
= 1<<1, /* Enable Config Reg WR */
250 TST_CFG_WRITE_OFF
= 1<<0, /* Disable Config Reg WR */
253 /* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */
255 CFG_CHIP_R_MSK
= 0xf<<4, /* Bit 7.. 4: Chip Revision */
256 /* Bit 3.. 2: reserved */
257 CFG_DIS_M2_CLK
= 1<<1, /* Disable Clock for 2nd MAC */
258 CFG_SNG_MAC
= 1<<0, /* MAC Config: 0=2 MACs / 1=1 MAC*/
261 /* B2_CHIP_ID 8 bit Chip Identification Number */
263 CHIP_ID_GENESIS
= 0x0a, /* Chip ID for GENESIS */
264 CHIP_ID_YUKON
= 0xb0, /* Chip ID for YUKON */
265 CHIP_ID_YUKON_LITE
= 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
266 CHIP_ID_YUKON_LP
= 0xb2, /* Chip ID for YUKON-LP */
267 CHIP_ID_YUKON_XL
= 0xb3, /* Chip ID for YUKON-2 XL */
268 CHIP_ID_YUKON_EC
= 0xb6, /* Chip ID for YUKON-2 EC */
269 CHIP_ID_YUKON_FE
= 0xb7, /* Chip ID for YUKON-2 FE */
271 CHIP_REV_YU_LITE_A1
= 3, /* Chip Rev. for YUKON-Lite A1,A2 */
272 CHIP_REV_YU_LITE_A3
= 7, /* Chip Rev. for YUKON-Lite A3 */
275 /* B2_TI_CTRL 8 bit Timer control */
276 /* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */
278 TIM_START
= 1<<2, /* Start Timer */
279 TIM_STOP
= 1<<1, /* Stop Timer */
280 TIM_CLR_IRQ
= 1<<0, /* Clear Timer IRQ (!IRQM) */
283 /* B2_TI_TEST 8 Bit Timer Test */
284 /* B2_IRQM_TEST 8 bit IRQ Moderation Timer Test */
285 /* B28_DPT_TST 8 bit Descriptor Poll Timer Test Reg */
287 TIM_T_ON
= 1<<2, /* Test mode on */
288 TIM_T_OFF
= 1<<1, /* Test mode off */
289 TIM_T_STEP
= 1<<0, /* Test step */
292 /* B2_GP_IO 32 bit General Purpose I/O Register */
294 GP_DIR_9
= 1<<25, /* IO_9 direct, 0=In/1=Out */
295 GP_DIR_8
= 1<<24, /* IO_8 direct, 0=In/1=Out */
296 GP_DIR_7
= 1<<23, /* IO_7 direct, 0=In/1=Out */
297 GP_DIR_6
= 1<<22, /* IO_6 direct, 0=In/1=Out */
298 GP_DIR_5
= 1<<21, /* IO_5 direct, 0=In/1=Out */
299 GP_DIR_4
= 1<<20, /* IO_4 direct, 0=In/1=Out */
300 GP_DIR_3
= 1<<19, /* IO_3 direct, 0=In/1=Out */
301 GP_DIR_2
= 1<<18, /* IO_2 direct, 0=In/1=Out */
302 GP_DIR_1
= 1<<17, /* IO_1 direct, 0=In/1=Out */
303 GP_DIR_0
= 1<<16, /* IO_0 direct, 0=In/1=Out */
305 GP_IO_9
= 1<<9, /* IO_9 pin */
306 GP_IO_8
= 1<<8, /* IO_8 pin */
307 GP_IO_7
= 1<<7, /* IO_7 pin */
308 GP_IO_6
= 1<<6, /* IO_6 pin */
309 GP_IO_5
= 1<<5, /* IO_5 pin */
310 GP_IO_4
= 1<<4, /* IO_4 pin */
311 GP_IO_3
= 1<<3, /* IO_3 pin */
312 GP_IO_2
= 1<<2, /* IO_2 pin */
313 GP_IO_1
= 1<<1, /* IO_1 pin */
314 GP_IO_0
= 1<<0, /* IO_0 pin */
317 /* Descriptor Bit Definition */
318 /* TxCtrl Transmit Buffer Control Field */
319 /* RxCtrl Receive Buffer Control Field */
321 BMU_OWN
= 1<<31, /* OWN bit: 0=host/1=BMU */
322 BMU_STF
= 1<<30, /* Start of Frame */
323 BMU_EOF
= 1<<29, /* End of Frame */
324 BMU_IRQ_EOB
= 1<<28, /* Req "End of Buffer" IRQ */
325 BMU_IRQ_EOF
= 1<<27, /* Req "End of Frame" IRQ */
326 /* TxCtrl specific bits */
327 BMU_STFWD
= 1<<26, /* (Tx) Store & Forward Frame */
328 BMU_NO_FCS
= 1<<25, /* (Tx) Disable MAC FCS (CRC) generation */
329 BMU_SW
= 1<<24, /* (Tx) 1 bit res. for SW use */
330 /* RxCtrl specific bits */
331 BMU_DEV_0
= 1<<26, /* (Rx) Transfer data to Dev0 */
332 BMU_STAT_VAL
= 1<<25, /* (Rx) Rx Status Valid */
333 BMU_TIST_VAL
= 1<<24, /* (Rx) Rx TimeStamp Valid */
334 /* Bit 23..16: BMU Check Opcodes */
335 BMU_CHECK
= 0x55<<16, /* Default BMU check */
336 BMU_TCP_CHECK
= 0x56<<16, /* Descr with TCP ext */
337 BMU_UDP_CHECK
= 0x57<<16, /* Descr with UDP ext (YUKON only) */
338 BMU_BBC
= 0xffffL
, /* Bit 15.. 0: Buffer Byte Counter */
341 /* B2_BSC_CTRL 8 bit Blink Source Counter Control */
343 BSC_START
= 1<<1, /* Start Blink Source Counter */
344 BSC_STOP
= 1<<0, /* Stop Blink Source Counter */
347 /* B2_BSC_STAT 8 bit Blink Source Counter Status */
349 BSC_SRC
= 1<<0, /* Blink Source, 0=Off / 1=On */
352 /* B2_BSC_TST 16 bit Blink Source Counter Test Reg */
354 BSC_T_ON
= 1<<2, /* Test mode on */
355 BSC_T_OFF
= 1<<1, /* Test mode off */
356 BSC_T_STEP
= 1<<0, /* Test step */
359 /* B3_RAM_ADDR 32 bit RAM Address, to read or write */
360 /* Bit 31..19: reserved */
361 #define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */
362 /* RAM Interface Registers */
364 /* B3_RI_CTRL 16 bit RAM Iface Control Register */
366 RI_CLR_RD_PERR
= 1<<9, /* Clear IRQ RAM Read Parity Err */
367 RI_CLR_WR_PERR
= 1<<8, /* Clear IRQ RAM Write Parity Err*/
369 RI_RST_CLR
= 1<<1, /* Clear RAM Interface Reset */
370 RI_RST_SET
= 1<<0, /* Set RAM Interface Reset */
373 /* MAC Arbiter Registers */
374 /* B3_MA_TO_CTRL 16 bit MAC Arbiter Timeout Ctrl Reg */
376 MA_FOE_ON
= 1<<3, /* XMAC Fast Output Enable ON */
377 MA_FOE_OFF
= 1<<2, /* XMAC Fast Output Enable OFF */
378 MA_RST_CLR
= 1<<1, /* Clear MAC Arbiter Reset */
379 MA_RST_SET
= 1<<0, /* Set MAC Arbiter Reset */
384 #define SK_MAC_TO_53 72 /* MAC arbiter timeout */
385 #define SK_PKT_TO_53 0x2000 /* Packet arbiter timeout */
386 #define SK_PKT_TO_MAX 0xffff /* Maximum value */
387 #define SK_RI_TO_53 36 /* RAM interface timeout */
389 /* Packet Arbiter Registers */
390 /* B3_PA_CTRL 16 bit Packet Arbiter Ctrl Register */
392 PA_CLR_TO_TX2
= 1<<13,/* Clear IRQ Packet Timeout TX2 */
393 PA_CLR_TO_TX1
= 1<<12,/* Clear IRQ Packet Timeout TX1 */
394 PA_CLR_TO_RX2
= 1<<11,/* Clear IRQ Packet Timeout RX2 */
395 PA_CLR_TO_RX1
= 1<<10,/* Clear IRQ Packet Timeout RX1 */
396 PA_ENA_TO_TX2
= 1<<9, /* Enable Timeout Timer TX2 */
397 PA_DIS_TO_TX2
= 1<<8, /* Disable Timeout Timer TX2 */
398 PA_ENA_TO_TX1
= 1<<7, /* Enable Timeout Timer TX1 */
399 PA_DIS_TO_TX1
= 1<<6, /* Disable Timeout Timer TX1 */
400 PA_ENA_TO_RX2
= 1<<5, /* Enable Timeout Timer RX2 */
401 PA_DIS_TO_RX2
= 1<<4, /* Disable Timeout Timer RX2 */
402 PA_ENA_TO_RX1
= 1<<3, /* Enable Timeout Timer RX1 */
403 PA_DIS_TO_RX1
= 1<<2, /* Disable Timeout Timer RX1 */
404 PA_RST_CLR
= 1<<1, /* Clear MAC Arbiter Reset */
405 PA_RST_SET
= 1<<0, /* Set MAC Arbiter Reset */
408 #define PA_ENA_TO_ALL (PA_ENA_TO_RX1 | PA_ENA_TO_RX2 |\
409 PA_ENA_TO_TX1 | PA_ENA_TO_TX2)
412 /* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
413 /* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */
414 /* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */
415 /* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */
416 /* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */
418 #define TXA_MAX_VAL 0x00ffffffUL /* Bit 23.. 0: Max TXA Timer/Cnt Val */
420 /* TXA_CTRL 8 bit Tx Arbiter Control Register */
422 TXA_ENA_FSYNC
= 1<<7, /* Enable force of sync Tx queue */
423 TXA_DIS_FSYNC
= 1<<6, /* Disable force of sync Tx queue */
424 TXA_ENA_ALLOC
= 1<<5, /* Enable alloc of free bandwidth */
425 TXA_DIS_ALLOC
= 1<<4, /* Disable alloc of free bandwidth */
426 TXA_START_RC
= 1<<3, /* Start sync Rate Control */
427 TXA_STOP_RC
= 1<<2, /* Stop sync Rate Control */
428 TXA_ENA_ARB
= 1<<1, /* Enable Tx Arbiter */
429 TXA_DIS_ARB
= 1<<0, /* Disable Tx Arbiter */
435 /* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
437 TXA_ITI_INI
= 0x0200,/* 32 bit Tx Arb Interval Timer Init Val*/
438 TXA_ITI_VAL
= 0x0204,/* 32 bit Tx Arb Interval Timer Value */
439 TXA_LIM_INI
= 0x0208,/* 32 bit Tx Arb Limit Counter Init Val */
440 TXA_LIM_VAL
= 0x020c,/* 32 bit Tx Arb Limit Counter Value */
441 TXA_CTRL
= 0x0210,/* 8 bit Tx Arbiter Control Register */
442 TXA_TEST
= 0x0211,/* 8 bit Tx Arbiter Test Register */
443 TXA_STAT
= 0x0212,/* 8 bit Tx Arbiter Status Register */
448 B6_EXT_REG
= 0x0300,/* External registers (GENESIS only) */
449 B7_CFG_SPC
= 0x0380,/* copy of the Configuration register */
450 B8_RQ1_REGS
= 0x0400,/* Receive Queue 1 */
451 B8_RQ2_REGS
= 0x0480,/* Receive Queue 2 */
452 B8_TS1_REGS
= 0x0600,/* Transmit sync queue 1 */
453 B8_TA1_REGS
= 0x0680,/* Transmit async queue 1 */
454 B8_TS2_REGS
= 0x0700,/* Transmit sync queue 2 */
455 B8_TA2_REGS
= 0x0780,/* Transmit sync queue 2 */
456 B16_RAM_REGS
= 0x0800,/* RAM Buffer Registers */
459 /* Queue Register Offsets, use Q_ADDR() to access */
461 B8_Q_REGS
= 0x0400, /* base of Queue registers */
462 Q_D
= 0x00, /* 8*32 bit Current Descriptor */
463 Q_DA_L
= 0x20, /* 32 bit Current Descriptor Address Low dWord */
464 Q_DA_H
= 0x24, /* 32 bit Current Descriptor Address High dWord */
465 Q_AC_L
= 0x28, /* 32 bit Current Address Counter Low dWord */
466 Q_AC_H
= 0x2c, /* 32 bit Current Address Counter High dWord */
467 Q_BC
= 0x30, /* 32 bit Current Byte Counter */
468 Q_CSR
= 0x34, /* 32 bit BMU Control/Status Register */
469 Q_F
= 0x38, /* 32 bit Flag Register */
470 Q_T1
= 0x3c, /* 32 bit Test Register 1 */
471 Q_T1_TR
= 0x3c, /* 8 bit Test Register 1 Transfer SM */
472 Q_T1_WR
= 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */
473 Q_T1_RD
= 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */
474 Q_T1_SV
= 0x3f, /* 8 bit Test Register 1 Supervisor SM */
475 Q_T2
= 0x40, /* 32 bit Test Register 2 */
476 Q_T3
= 0x44, /* 32 bit Test Register 3 */
479 #define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
481 /* RAM Buffer Register Offsets */
484 RB_START
= 0x00,/* 32 bit RAM Buffer Start Address */
485 RB_END
= 0x04,/* 32 bit RAM Buffer End Address */
486 RB_WP
= 0x08,/* 32 bit RAM Buffer Write Pointer */
487 RB_RP
= 0x0c,/* 32 bit RAM Buffer Read Pointer */
488 RB_RX_UTPP
= 0x10,/* 32 bit Rx Upper Threshold, Pause Packet */
489 RB_RX_LTPP
= 0x14,/* 32 bit Rx Lower Threshold, Pause Packet */
490 RB_RX_UTHP
= 0x18,/* 32 bit Rx Upper Threshold, High Prio */
491 RB_RX_LTHP
= 0x1c,/* 32 bit Rx Lower Threshold, High Prio */
492 /* 0x10 - 0x1f: reserved at Tx RAM Buffer Registers */
493 RB_PC
= 0x20,/* 32 bit RAM Buffer Packet Counter */
494 RB_LEV
= 0x24,/* 32 bit RAM Buffer Level Register */
495 RB_CTRL
= 0x28,/* 32 bit RAM Buffer Control Register */
496 RB_TST1
= 0x29,/* 8 bit RAM Buffer Test Register 1 */
497 RB_TST2
= 0x2a,/* 8 bit RAM Buffer Test Register 2 */
500 /* Receive and Transmit Queues */
502 Q_R1
= 0x0000, /* Receive Queue 1 */
503 Q_R2
= 0x0080, /* Receive Queue 2 */
504 Q_XS1
= 0x0200, /* Synchronous Transmit Queue 1 */
505 Q_XA1
= 0x0280, /* Asynchronous Transmit Queue 1 */
506 Q_XS2
= 0x0300, /* Synchronous Transmit Queue 2 */
507 Q_XA2
= 0x0380, /* Asynchronous Transmit Queue 2 */
510 /* Different MAC Types */
512 SK_MAC_XMAC
= 0, /* Xaqti XMAC II */
513 SK_MAC_GMAC
= 1, /* Marvell GMAC */
516 /* Different PHY Types */
518 SK_PHY_XMAC
= 0,/* integrated in XMAC II */
519 SK_PHY_BCOM
= 1,/* Broadcom BCM5400 */
520 SK_PHY_LONE
= 2,/* Level One LXT1000 [not supported]*/
521 SK_PHY_NAT
= 3,/* National DP83891 [not supported] */
522 SK_PHY_MARV_COPPER
= 4,/* Marvell 88E1011S */
523 SK_PHY_MARV_FIBER
= 5,/* Marvell 88E1011S working on fiber */
526 /* PHY addresses (bits 12..8 of PHY address reg) */
528 PHY_ADDR_XMAC
= 0<<8,
529 PHY_ADDR_BCOM
= 1<<8,
531 /* GPHY address (bits 15..11 of SMI control reg) */
535 #define RB_ADDR(offs, queue) ((u16)B16_RAM_REGS + (u16)(queue) + (offs))
537 /* Receive MAC FIFO, Receive LED, and Link_Sync regs (GENESIS only) */
539 RX_MFF_EA
= 0x0c00,/* 32 bit Receive MAC FIFO End Address */
540 RX_MFF_WP
= 0x0c04,/* 32 bit Receive MAC FIFO Write Pointer */
542 RX_MFF_RP
= 0x0c0c,/* 32 bit Receive MAC FIFO Read Pointer */
543 RX_MFF_PC
= 0x0c10,/* 32 bit Receive MAC FIFO Packet Cnt */
544 RX_MFF_LEV
= 0x0c14,/* 32 bit Receive MAC FIFO Level */
545 RX_MFF_CTRL1
= 0x0c18,/* 16 bit Receive MAC FIFO Control Reg 1*/
546 RX_MFF_STAT_TO
= 0x0c1a,/* 8 bit Receive MAC Status Timeout */
547 RX_MFF_TIST_TO
= 0x0c1b,/* 8 bit Receive MAC Time Stamp Timeout */
548 RX_MFF_CTRL2
= 0x0c1c,/* 8 bit Receive MAC FIFO Control Reg 2*/
549 RX_MFF_TST1
= 0x0c1d,/* 8 bit Receive MAC FIFO Test Reg 1 */
550 RX_MFF_TST2
= 0x0c1e,/* 8 bit Receive MAC FIFO Test Reg 2 */
552 RX_LED_INI
= 0x0c20,/* 32 bit Receive LED Cnt Init Value */
553 RX_LED_VAL
= 0x0c24,/* 32 bit Receive LED Cnt Current Value */
554 RX_LED_CTRL
= 0x0c28,/* 8 bit Receive LED Cnt Control Reg */
555 RX_LED_TST
= 0x0c29,/* 8 bit Receive LED Cnt Test Register */
557 LNK_SYNC_INI
= 0x0c30,/* 32 bit Link Sync Cnt Init Value */
558 LNK_SYNC_VAL
= 0x0c34,/* 32 bit Link Sync Cnt Current Value */
559 LNK_SYNC_CTRL
= 0x0c38,/* 8 bit Link Sync Cnt Control Register */
560 LNK_SYNC_TST
= 0x0c39,/* 8 bit Link Sync Cnt Test Register */
561 LNK_LED_REG
= 0x0c3c,/* 8 bit Link LED Register */
564 /* Receive and Transmit MAC FIFO Registers (GENESIS only) */
565 /* RX_MFF_CTRL1 16 bit Receive MAC FIFO Control Reg 1 */
567 MFF_ENA_RDY_PAT
= 1<<13, /* Enable Ready Patch */
568 MFF_DIS_RDY_PAT
= 1<<12, /* Disable Ready Patch */
569 MFF_ENA_TIM_PAT
= 1<<11, /* Enable Timing Patch */
570 MFF_DIS_TIM_PAT
= 1<<10, /* Disable Timing Patch */
571 MFF_ENA_ALM_FUL
= 1<<9, /* Enable AlmostFull Sign */
572 MFF_DIS_ALM_FUL
= 1<<8, /* Disable AlmostFull Sign */
573 MFF_ENA_PAUSE
= 1<<7, /* Enable Pause Signaling */
574 MFF_DIS_PAUSE
= 1<<6, /* Disable Pause Signaling */
575 MFF_ENA_FLUSH
= 1<<5, /* Enable Frame Flushing */
576 MFF_DIS_FLUSH
= 1<<4, /* Disable Frame Flushing */
577 MFF_ENA_TIST
= 1<<3, /* Enable Time Stamp Gener */
578 MFF_DIS_TIST
= 1<<2, /* Disable Time Stamp Gener */
579 MFF_CLR_INTIST
= 1<<1, /* Clear IRQ No Time Stamp */
580 MFF_CLR_INSTAT
= 1<<0, /* Clear IRQ No Status */
581 MFF_RX_CTRL_DEF
= MFF_ENA_TIM_PAT
,
584 /* TX_MFF_CTRL1 16 bit Transmit MAC FIFO Control Reg 1 */
586 MFF_CLR_PERR
= 1<<15, /* Clear Parity Error IRQ */
588 MFF_ENA_PKT_REC
= 1<<13, /* Enable Packet Recovery */
589 MFF_DIS_PKT_REC
= 1<<12, /* Disable Packet Recovery */
591 MFF_ENA_W4E
= 1<<7, /* Enable Wait for Empty */
592 MFF_DIS_W4E
= 1<<6, /* Disable Wait for Empty */
594 MFF_ENA_LOOPB
= 1<<3, /* Enable Loopback */
595 MFF_DIS_LOOPB
= 1<<2, /* Disable Loopback */
596 MFF_CLR_MAC_RST
= 1<<1, /* Clear XMAC Reset */
597 MFF_SET_MAC_RST
= 1<<0, /* Set XMAC Reset */
599 MFF_TX_CTRL_DEF
= MFF_ENA_PKT_REC
| (u16
) MFF_ENA_TIM_PAT
| MFF_ENA_FLUSH
,
603 /* RX_MFF_TST2 8 bit Receive MAC FIFO Test Register 2 */
604 /* TX_MFF_TST2 8 bit Transmit MAC FIFO Test Register 2 */
606 MFF_WSP_T_ON
= 1<<6, /* Tx: Write Shadow Ptr TestOn */
607 MFF_WSP_T_OFF
= 1<<5, /* Tx: Write Shadow Ptr TstOff */
608 MFF_WSP_INC
= 1<<4, /* Tx: Write Shadow Ptr Increment */
609 MFF_PC_DEC
= 1<<3, /* Packet Counter Decrement */
610 MFF_PC_T_ON
= 1<<2, /* Packet Counter Test On */
611 MFF_PC_T_OFF
= 1<<1, /* Packet Counter Test Off */
612 MFF_PC_INC
= 1<<0, /* Packet Counter Increment */
615 /* RX_MFF_TST1 8 bit Receive MAC FIFO Test Register 1 */
616 /* TX_MFF_TST1 8 bit Transmit MAC FIFO Test Register 1 */
618 MFF_WP_T_ON
= 1<<6, /* Write Pointer Test On */
619 MFF_WP_T_OFF
= 1<<5, /* Write Pointer Test Off */
620 MFF_WP_INC
= 1<<4, /* Write Pointer Increm */
622 MFF_RP_T_ON
= 1<<2, /* Read Pointer Test On */
623 MFF_RP_T_OFF
= 1<<1, /* Read Pointer Test Off */
624 MFF_RP_DEC
= 1<<0, /* Read Pointer Decrement */
627 /* RX_MFF_CTRL2 8 bit Receive MAC FIFO Control Reg 2 */
628 /* TX_MFF_CTRL2 8 bit Transmit MAC FIFO Control Reg 2 */
630 MFF_ENA_OP_MD
= 1<<3, /* Enable Operation Mode */
631 MFF_DIS_OP_MD
= 1<<2, /* Disable Operation Mode */
632 MFF_RST_CLR
= 1<<1, /* Clear MAC FIFO Reset */
633 MFF_RST_SET
= 1<<0, /* Set MAC FIFO Reset */
637 /* Link LED Counter Registers (GENESIS only) */
639 /* RX_LED_CTRL 8 bit Receive LED Cnt Control Reg */
640 /* TX_LED_CTRL 8 bit Transmit LED Cnt Control Reg */
641 /* LNK_SYNC_CTRL 8 bit Link Sync Cnt Control Register */
643 LED_START
= 1<<2, /* Start Timer */
644 LED_STOP
= 1<<1, /* Stop Timer */
645 LED_STATE
= 1<<0, /* Rx/Tx: LED State, 1=LED on */
648 /* RX_LED_TST 8 bit Receive LED Cnt Test Register */
649 /* TX_LED_TST 8 bit Transmit LED Cnt Test Register */
650 /* LNK_SYNC_TST 8 bit Link Sync Cnt Test Register */
652 LED_T_ON
= 1<<2, /* LED Counter Test mode On */
653 LED_T_OFF
= 1<<1, /* LED Counter Test mode Off */
654 LED_T_STEP
= 1<<0, /* LED Counter Step */
657 /* LNK_LED_REG 8 bit Link LED Register */
659 LED_BLK_ON
= 1<<5, /* Link LED Blinking On */
660 LED_BLK_OFF
= 1<<4, /* Link LED Blinking Off */
661 LED_SYNC_ON
= 1<<3, /* Use Sync Wire to switch LED */
662 LED_SYNC_OFF
= 1<<2, /* Disable Sync Wire Input */
663 LED_ON
= 1<<1, /* switch LED on */
664 LED_OFF
= 1<<0, /* switch LED off */
667 /* Receive GMAC FIFO (YUKON) */
669 RX_GMF_EA
= 0x0c40,/* 32 bit Rx GMAC FIFO End Address */
670 RX_GMF_AF_THR
= 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */
671 RX_GMF_CTRL_T
= 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */
672 RX_GMF_FL_MSK
= 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */
673 RX_GMF_FL_THR
= 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */
674 RX_GMF_WP
= 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */
675 RX_GMF_WLEV
= 0x0c68,/* 32 bit Rx GMAC FIFO Write Level */
676 RX_GMF_RP
= 0x0c70,/* 32 bit Rx GMAC FIFO Read Pointer */
677 RX_GMF_RLEV
= 0x0c78,/* 32 bit Rx GMAC FIFO Read Level */
681 /* TXA_TEST 8 bit Tx Arbiter Test Register */
683 TXA_INT_T_ON
= 1<<5, /* Tx Arb Interval Timer Test On */
684 TXA_INT_T_OFF
= 1<<4, /* Tx Arb Interval Timer Test Off */
685 TXA_INT_T_STEP
= 1<<3, /* Tx Arb Interval Timer Step */
686 TXA_LIM_T_ON
= 1<<2, /* Tx Arb Limit Timer Test On */
687 TXA_LIM_T_OFF
= 1<<1, /* Tx Arb Limit Timer Test Off */
688 TXA_LIM_T_STEP
= 1<<0, /* Tx Arb Limit Timer Step */
691 /* TXA_STAT 8 bit Tx Arbiter Status Register */
693 TXA_PRIO_XS
= 1<<0, /* sync queue has prio to send */
697 /* Q_BC 32 bit Current Byte Counter */
699 /* BMU Control Status Registers */
700 /* B0_R1_CSR 32 bit BMU Ctrl/Stat Rx Queue 1 */
701 /* B0_R2_CSR 32 bit BMU Ctrl/Stat Rx Queue 2 */
702 /* B0_XA1_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 1 */
703 /* B0_XS1_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 1 */
704 /* B0_XA2_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 2 */
705 /* B0_XS2_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 2 */
706 /* Q_CSR 32 bit BMU Control/Status Register */
709 CSR_SV_IDLE
= 1<<24, /* BMU SM Idle */
711 CSR_DESC_CLR
= 1<<21, /* Clear Reset for Descr */
712 CSR_DESC_SET
= 1<<20, /* Set Reset for Descr */
713 CSR_FIFO_CLR
= 1<<19, /* Clear Reset for FIFO */
714 CSR_FIFO_SET
= 1<<18, /* Set Reset for FIFO */
715 CSR_HPI_RUN
= 1<<17, /* Release HPI SM */
716 CSR_HPI_RST
= 1<<16, /* Reset HPI SM to Idle */
717 CSR_SV_RUN
= 1<<15, /* Release Supervisor SM */
718 CSR_SV_RST
= 1<<14, /* Reset Supervisor SM */
719 CSR_DREAD_RUN
= 1<<13, /* Release Descr Read SM */
720 CSR_DREAD_RST
= 1<<12, /* Reset Descr Read SM */
721 CSR_DWRITE_RUN
= 1<<11, /* Release Descr Write SM */
722 CSR_DWRITE_RST
= 1<<10, /* Reset Descr Write SM */
723 CSR_TRANS_RUN
= 1<<9, /* Release Transfer SM */
724 CSR_TRANS_RST
= 1<<8, /* Reset Transfer SM */
725 CSR_ENA_POL
= 1<<7, /* Enable Descr Polling */
726 CSR_DIS_POL
= 1<<6, /* Disable Descr Polling */
727 CSR_STOP
= 1<<5, /* Stop Rx/Tx Queue */
728 CSR_START
= 1<<4, /* Start Rx/Tx Queue */
729 CSR_IRQ_CL_P
= 1<<3, /* (Rx) Clear Parity IRQ */
730 CSR_IRQ_CL_B
= 1<<2, /* Clear EOB IRQ */
731 CSR_IRQ_CL_F
= 1<<1, /* Clear EOF IRQ */
732 CSR_IRQ_CL_C
= 1<<0, /* Clear ERR IRQ */
735 #define CSR_SET_RESET (CSR_DESC_SET | CSR_FIFO_SET | CSR_HPI_RST |\
736 CSR_SV_RST | CSR_DREAD_RST | CSR_DWRITE_RST |\
738 #define CSR_CLR_RESET (CSR_DESC_CLR | CSR_FIFO_CLR | CSR_HPI_RUN |\
739 CSR_SV_RUN | CSR_DREAD_RUN | CSR_DWRITE_RUN |\
742 /* Q_F 32 bit Flag Register */
744 F_ALM_FULL
= 1<<27, /* Rx FIFO: almost full */
745 F_EMPTY
= 1<<27, /* Tx FIFO: empty flag */
746 F_FIFO_EOF
= 1<<26, /* Tag (EOF Flag) bit in FIFO */
747 F_WM_REACHED
= 1<<25, /* Watermark reached */
749 F_FIFO_LEVEL
= 0x1fL
<<16, /* Bit 23..16: # of Qwords in FIFO */
750 F_WATER_MARK
= 0x0007ffL
, /* Bit 10.. 0: Watermark */
753 /* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */
754 /* RB_START 32 bit RAM Buffer Start Address */
755 /* RB_END 32 bit RAM Buffer End Address */
756 /* RB_WP 32 bit RAM Buffer Write Pointer */
757 /* RB_RP 32 bit RAM Buffer Read Pointer */
758 /* RB_RX_UTPP 32 bit Rx Upper Threshold, Pause Pack */
759 /* RB_RX_LTPP 32 bit Rx Lower Threshold, Pause Pack */
760 /* RB_RX_UTHP 32 bit Rx Upper Threshold, High Prio */
761 /* RB_RX_LTHP 32 bit Rx Lower Threshold, High Prio */
762 /* RB_PC 32 bit RAM Buffer Packet Counter */
763 /* RB_LEV 32 bit RAM Buffer Level Register */
765 #define RB_MSK 0x0007ffff /* Bit 18.. 0: RAM Buffer Pointer Bits */
766 /* RB_TST2 8 bit RAM Buffer Test Register 2 */
767 /* RB_TST1 8 bit RAM Buffer Test Register 1 */
769 /* RB_CTRL 8 bit RAM Buffer Control Register */
771 RB_ENA_STFWD
= 1<<5, /* Enable Store & Forward */
772 RB_DIS_STFWD
= 1<<4, /* Disable Store & Forward */
773 RB_ENA_OP_MD
= 1<<3, /* Enable Operation Mode */
774 RB_DIS_OP_MD
= 1<<2, /* Disable Operation Mode */
775 RB_RST_CLR
= 1<<1, /* Clear RAM Buf STM Reset */
776 RB_RST_SET
= 1<<0, /* Set RAM Buf STM Reset */
779 /* Transmit MAC FIFO and Transmit LED Registers (GENESIS only), */
781 TX_MFF_EA
= 0x0d00,/* 32 bit Transmit MAC FIFO End Address */
782 TX_MFF_WP
= 0x0d04,/* 32 bit Transmit MAC FIFO WR Pointer */
783 TX_MFF_WSP
= 0x0d08,/* 32 bit Transmit MAC FIFO WR Shadow Ptr */
784 TX_MFF_RP
= 0x0d0c,/* 32 bit Transmit MAC FIFO RD Pointer */
785 TX_MFF_PC
= 0x0d10,/* 32 bit Transmit MAC FIFO Packet Cnt */
786 TX_MFF_LEV
= 0x0d14,/* 32 bit Transmit MAC FIFO Level */
787 TX_MFF_CTRL1
= 0x0d18,/* 16 bit Transmit MAC FIFO Ctrl Reg 1 */
788 TX_MFF_WAF
= 0x0d1a,/* 8 bit Transmit MAC Wait after flush */
790 TX_MFF_CTRL2
= 0x0d1c,/* 8 bit Transmit MAC FIFO Ctrl Reg 2 */
791 TX_MFF_TST1
= 0x0d1d,/* 8 bit Transmit MAC FIFO Test Reg 1 */
792 TX_MFF_TST2
= 0x0d1e,/* 8 bit Transmit MAC FIFO Test Reg 2 */
794 TX_LED_INI
= 0x0d20,/* 32 bit Transmit LED Cnt Init Value */
795 TX_LED_VAL
= 0x0d24,/* 32 bit Transmit LED Cnt Current Val */
796 TX_LED_CTRL
= 0x0d28,/* 8 bit Transmit LED Cnt Control Reg */
797 TX_LED_TST
= 0x0d29,/* 8 bit Transmit LED Cnt Test Reg */
800 /* Counter and Timer constants, for a host clock of 62.5 MHz */
801 #define SK_XMIT_DUR 0x002faf08UL /* 50 ms */
802 #define SK_BLK_DUR 0x01dcd650UL /* 500 ms */
804 #define SK_DPOLL_DEF 0x00ee6b28UL /* 250 ms at 62.5 MHz */
806 #define SK_DPOLL_MAX 0x00ffffffUL /* 268 ms at 62.5 MHz */
807 /* 215 ms at 78.12 MHz */
809 #define SK_FACT_62 100 /* is given in percent */
810 #define SK_FACT_53 85 /* on GENESIS: 53.12 MHz */
811 #define SK_FACT_78 125 /* on YUKON: 78.12 MHz */
814 /* Transmit GMAC FIFO (YUKON only) */
816 TX_GMF_EA
= 0x0d40,/* 32 bit Tx GMAC FIFO End Address */
817 TX_GMF_AE_THR
= 0x0d44,/* 32 bit Tx GMAC FIFO Almost Empty Thresh.*/
818 TX_GMF_CTRL_T
= 0x0d48,/* 32 bit Tx GMAC FIFO Control/Test */
820 TX_GMF_WP
= 0x0d60,/* 32 bit Tx GMAC FIFO Write Pointer */
821 TX_GMF_WSP
= 0x0d64,/* 32 bit Tx GMAC FIFO Write Shadow Ptr. */
822 TX_GMF_WLEV
= 0x0d68,/* 32 bit Tx GMAC FIFO Write Level */
824 TX_GMF_RP
= 0x0d70,/* 32 bit Tx GMAC FIFO Read Pointer */
825 TX_GMF_RSTP
= 0x0d74,/* 32 bit Tx GMAC FIFO Restart Pointer */
826 TX_GMF_RLEV
= 0x0d78,/* 32 bit Tx GMAC FIFO Read Level */
828 /* Descriptor Poll Timer Registers */
829 B28_DPT_INI
= 0x0e00,/* 24 bit Descriptor Poll Timer Init Val */
830 B28_DPT_VAL
= 0x0e04,/* 24 bit Descriptor Poll Timer Curr Val */
831 B28_DPT_CTRL
= 0x0e08,/* 8 bit Descriptor Poll Timer Ctrl Reg */
833 B28_DPT_TST
= 0x0e0a,/* 8 bit Descriptor Poll Timer Test Reg */
835 /* Time Stamp Timer Registers (YUKON only) */
836 GMAC_TI_ST_VAL
= 0x0e14,/* 32 bit Time Stamp Timer Curr Val */
837 GMAC_TI_ST_CTRL
= 0x0e18,/* 8 bit Time Stamp Timer Ctrl Reg */
838 GMAC_TI_ST_TST
= 0x0e1a,/* 8 bit Time Stamp Timer Test Reg */
845 LINKLED_LINKSYNC_OFF
= 0x04,
846 LINKLED_LINKSYNC_ON
= 0x08,
847 LINKLED_BLINK_OFF
= 0x10,
848 LINKLED_BLINK_ON
= 0x20,
851 /* GMAC and GPHY Control Registers (YUKON only) */
853 GMAC_CTRL
= 0x0f00,/* 32 bit GMAC Control Reg */
854 GPHY_CTRL
= 0x0f04,/* 32 bit GPHY Control Reg */
855 GMAC_IRQ_SRC
= 0x0f08,/* 8 bit GMAC Interrupt Source Reg */
856 GMAC_IRQ_MSK
= 0x0f0c,/* 8 bit GMAC Interrupt Mask Reg */
857 GMAC_LINK_CTRL
= 0x0f10,/* 16 bit Link Control Reg */
859 /* Wake-up Frame Pattern Match Control Registers (YUKON only) */
861 WOL_REG_OFFS
= 0x20,/* HW-Bug: Address is + 0x20 against spec. */
863 WOL_CTRL_STAT
= 0x0f20,/* 16 bit WOL Control/Status Reg */
864 WOL_MATCH_CTL
= 0x0f22,/* 8 bit WOL Match Control Reg */
865 WOL_MATCH_RES
= 0x0f23,/* 8 bit WOL Match Result Reg */
866 WOL_MAC_ADDR
= 0x0f24,/* 32 bit WOL MAC Address */
867 WOL_PATT_RPTR
= 0x0f2c,/* 8 bit WOL Pattern Read Pointer */
869 /* WOL Pattern Length Registers (YUKON only) */
871 WOL_PATT_LEN_LO
= 0x0f30,/* 32 bit WOL Pattern Length 3..0 */
872 WOL_PATT_LEN_HI
= 0x0f34,/* 24 bit WOL Pattern Length 6..4 */
874 /* WOL Pattern Counter Registers (YUKON only) */
876 WOL_PATT_CNT_0
= 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */
877 WOL_PATT_CNT_4
= 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */
881 WOL_PATT_RAM_1
= 0x1000,/* WOL Pattern RAM Link 1 */
882 WOL_PATT_RAM_2
= 0x1400,/* WOL Pattern RAM Link 2 */
886 BASE_XMAC_1
= 0x2000,/* XMAC 1 registers */
887 BASE_GMAC_1
= 0x2800,/* GMAC 1 registers */
888 BASE_XMAC_2
= 0x3000,/* XMAC 2 registers */
889 BASE_GMAC_2
= 0x3800,/* GMAC 2 registers */
893 * Receive Frame Status Encoding
896 XMR_FS_LEN
= 0x3fff<<18, /* Bit 31..18: Rx Frame Length */
897 XMR_FS_LEN_SHIFT
= 18,
898 XMR_FS_2L_VLAN
= 1<<17, /* Bit 17: tagged wh 2Lev VLAN ID*/
899 XMR_FS_1_VLAN
= 1<<16, /* Bit 16: tagged wh 1ev VLAN ID*/
900 XMR_FS_BC
= 1<<15, /* Bit 15: Broadcast Frame */
901 XMR_FS_MC
= 1<<14, /* Bit 14: Multicast Frame */
902 XMR_FS_UC
= 1<<13, /* Bit 13: Unicast Frame */
904 XMR_FS_BURST
= 1<<11, /* Bit 11: Burst Mode */
905 XMR_FS_CEX_ERR
= 1<<10, /* Bit 10: Carrier Ext. Error */
906 XMR_FS_802_3
= 1<<9, /* Bit 9: 802.3 Frame */
907 XMR_FS_COL_ERR
= 1<<8, /* Bit 8: Collision Error */
908 XMR_FS_CAR_ERR
= 1<<7, /* Bit 7: Carrier Event Error */
909 XMR_FS_LEN_ERR
= 1<<6, /* Bit 6: In-Range Length Error */
910 XMR_FS_FRA_ERR
= 1<<5, /* Bit 5: Framing Error */
911 XMR_FS_RUNT
= 1<<4, /* Bit 4: Runt Frame */
912 XMR_FS_LNG_ERR
= 1<<3, /* Bit 3: Giant (Jumbo) Frame */
913 XMR_FS_FCS_ERR
= 1<<2, /* Bit 2: Frame Check Sequ Err */
914 XMR_FS_ERR
= 1<<1, /* Bit 1: Frame Error */
915 XMR_FS_MCTRL
= 1<<0, /* Bit 0: MAC Control Packet */
918 * XMR_FS_ERR will be set if
919 * XMR_FS_FCS_ERR, XMR_FS_LNG_ERR, XMR_FS_RUNT,
920 * XMR_FS_FRA_ERR, XMR_FS_LEN_ERR, or XMR_FS_CEX_ERR
921 * is set. XMR_FS_LNG_ERR and XMR_FS_LEN_ERR will issue
922 * XMR_FS_ERR unless the corresponding bit in the Receive Command
928 ,* XMAC-PHY Registers, indirect addressed over the XMAC
931 PHY_XMAC_CTRL
= 0x00,/* 16 bit r/w PHY Control Register */
932 PHY_XMAC_STAT
= 0x01,/* 16 bit r/w PHY Status Register */
933 PHY_XMAC_ID0
= 0x02,/* 16 bit r/o PHY ID0 Register */
934 PHY_XMAC_ID1
= 0x03,/* 16 bit r/o PHY ID1 Register */
935 PHY_XMAC_AUNE_ADV
= 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
936 PHY_XMAC_AUNE_LP
= 0x05,/* 16 bit r/o Link Partner Abi Reg */
937 PHY_XMAC_AUNE_EXP
= 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
938 PHY_XMAC_NEPG
= 0x07,/* 16 bit r/w Next Page Register */
939 PHY_XMAC_NEPG_LP
= 0x08,/* 16 bit r/o Next Page Link Partner */
941 PHY_XMAC_EXT_STAT
= 0x0f,/* 16 bit r/o Ext Status Register */
942 PHY_XMAC_RES_ABI
= 0x10,/* 16 bit r/o PHY Resolved Ability */
945 * Broadcom-PHY Registers, indirect addressed over XMAC
948 PHY_BCOM_CTRL
= 0x00,/* 16 bit r/w PHY Control Register */
949 PHY_BCOM_STAT
= 0x01,/* 16 bit r/o PHY Status Register */
950 PHY_BCOM_ID0
= 0x02,/* 16 bit r/o PHY ID0 Register */
951 PHY_BCOM_ID1
= 0x03,/* 16 bit r/o PHY ID1 Register */
952 PHY_BCOM_AUNE_ADV
= 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
953 PHY_BCOM_AUNE_LP
= 0x05,/* 16 bit r/o Link Part Ability Reg */
954 PHY_BCOM_AUNE_EXP
= 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
955 PHY_BCOM_NEPG
= 0x07,/* 16 bit r/w Next Page Register */
956 PHY_BCOM_NEPG_LP
= 0x08,/* 16 bit r/o Next Page Link Partner */
957 /* Broadcom-specific registers */
958 PHY_BCOM_1000T_CTRL
= 0x09,/* 16 bit r/w 1000Base-T Control Reg */
959 PHY_BCOM_1000T_STAT
= 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
960 PHY_BCOM_EXT_STAT
= 0x0f,/* 16 bit r/o Extended Status Reg */
961 PHY_BCOM_P_EXT_CTRL
= 0x10,/* 16 bit r/w PHY Extended Ctrl Reg */
962 PHY_BCOM_P_EXT_STAT
= 0x11,/* 16 bit r/o PHY Extended Stat Reg */
963 PHY_BCOM_RE_CTR
= 0x12,/* 16 bit r/w Receive Error Counter */
964 PHY_BCOM_FC_CTR
= 0x13,/* 16 bit r/w False Carrier Sense Cnt */
965 PHY_BCOM_RNO_CTR
= 0x14,/* 16 bit r/w Receiver NOT_OK Cnt */
967 PHY_BCOM_AUX_CTRL
= 0x18,/* 16 bit r/w Auxiliary Control Reg */
968 PHY_BCOM_AUX_STAT
= 0x19,/* 16 bit r/o Auxiliary Stat Summary */
969 PHY_BCOM_INT_STAT
= 0x1a,/* 16 bit r/o Interrupt Status Reg */
970 PHY_BCOM_INT_MASK
= 0x1b,/* 16 bit r/w Interrupt Mask Reg */
974 * Marvel-PHY Registers, indirect addressed over GMAC
977 PHY_MARV_CTRL
= 0x00,/* 16 bit r/w PHY Control Register */
978 PHY_MARV_STAT
= 0x01,/* 16 bit r/o PHY Status Register */
979 PHY_MARV_ID0
= 0x02,/* 16 bit r/o PHY ID0 Register */
980 PHY_MARV_ID1
= 0x03,/* 16 bit r/o PHY ID1 Register */
981 PHY_MARV_AUNE_ADV
= 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
982 PHY_MARV_AUNE_LP
= 0x05,/* 16 bit r/o Link Part Ability Reg */
983 PHY_MARV_AUNE_EXP
= 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
984 PHY_MARV_NEPG
= 0x07,/* 16 bit r/w Next Page Register */
985 PHY_MARV_NEPG_LP
= 0x08,/* 16 bit r/o Next Page Link Partner */
986 /* Marvel-specific registers */
987 PHY_MARV_1000T_CTRL
= 0x09,/* 16 bit r/w 1000Base-T Control Reg */
988 PHY_MARV_1000T_STAT
= 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
989 PHY_MARV_EXT_STAT
= 0x0f,/* 16 bit r/o Extended Status Reg */
990 PHY_MARV_PHY_CTRL
= 0x10,/* 16 bit r/w PHY Specific Ctrl Reg */
991 PHY_MARV_PHY_STAT
= 0x11,/* 16 bit r/o PHY Specific Stat Reg */
992 PHY_MARV_INT_MASK
= 0x12,/* 16 bit r/w Interrupt Mask Reg */
993 PHY_MARV_INT_STAT
= 0x13,/* 16 bit r/o Interrupt Status Reg */
994 PHY_MARV_EXT_CTRL
= 0x14,/* 16 bit r/w Ext. PHY Specific Ctrl */
995 PHY_MARV_RXE_CNT
= 0x15,/* 16 bit r/w Receive Error Counter */
996 PHY_MARV_EXT_ADR
= 0x16,/* 16 bit r/w Ext. Ad. for Cable Diag. */
997 PHY_MARV_PORT_IRQ
= 0x17,/* 16 bit r/o Port 0 IRQ (88E1111 only) */
998 PHY_MARV_LED_CTRL
= 0x18,/* 16 bit r/w LED Control Reg */
999 PHY_MARV_LED_OVER
= 0x19,/* 16 bit r/w Manual LED Override Reg */
1000 PHY_MARV_EXT_CTRL_2
= 0x1a,/* 16 bit r/w Ext. PHY Specific Ctrl 2 */
1001 PHY_MARV_EXT_P_STAT
= 0x1b,/* 16 bit r/w Ext. PHY Spec. Stat Reg */
1002 PHY_MARV_CABLE_DIAG
= 0x1c,/* 16 bit r/o Cable Diagnostic Reg */
1003 PHY_MARV_PAGE_ADDR
= 0x1d,/* 16 bit r/w Extended Page Address Reg */
1004 PHY_MARV_PAGE_DATA
= 0x1e,/* 16 bit r/w Extended Page Data Reg */
1006 /* for 10/100 Fast Ethernet PHY (88E3082 only) */
1007 PHY_MARV_FE_LED_PAR
= 0x16,/* 16 bit r/w LED Parallel Select Reg. */
1008 PHY_MARV_FE_LED_SER
= 0x17,/* 16 bit r/w LED Stream Select S. LED */
1009 PHY_MARV_FE_VCT_TX
= 0x1a,/* 16 bit r/w VCT Reg. for TXP/N Pins */
1010 PHY_MARV_FE_VCT_RX
= 0x1b,/* 16 bit r/o VCT Reg. for RXP/N Pins */
1011 PHY_MARV_FE_SPEC_2
= 0x1c,/* 16 bit r/w Specific Control Reg. 2 */
1015 PHY_CT_RESET
= 1<<15, /* Bit 15: (sc) clear all PHY related regs */
1016 PHY_CT_LOOP
= 1<<14, /* Bit 14: enable Loopback over PHY */
1017 PHY_CT_SPS_LSB
= 1<<13, /* Bit 13: Speed select, lower bit */
1018 PHY_CT_ANE
= 1<<12, /* Bit 12: Auto-Negotiation Enabled */
1019 PHY_CT_PDOWN
= 1<<11, /* Bit 11: Power Down Mode */
1020 PHY_CT_ISOL
= 1<<10, /* Bit 10: Isolate Mode */
1021 PHY_CT_RE_CFG
= 1<<9, /* Bit 9: (sc) Restart Auto-Negotiation */
1022 PHY_CT_DUP_MD
= 1<<8, /* Bit 8: Duplex Mode */
1023 PHY_CT_COL_TST
= 1<<7, /* Bit 7: Collision Test enabled */
1024 PHY_CT_SPS_MSB
= 1<<6, /* Bit 6: Speed select, upper bit */
1028 PHY_CT_SP1000
= PHY_CT_SPS_MSB
, /* enable speed of 1000 Mbps */
1029 PHY_CT_SP100
= PHY_CT_SPS_LSB
, /* enable speed of 100 Mbps */
1030 PHY_CT_SP10
= 0, /* enable speed of 10 Mbps */
1034 PHY_ST_EXT_ST
= 1<<8, /* Bit 8: Extended Status Present */
1036 PHY_ST_PRE_SUP
= 1<<6, /* Bit 6: Preamble Suppression */
1037 PHY_ST_AN_OVER
= 1<<5, /* Bit 5: Auto-Negotiation Over */
1038 PHY_ST_REM_FLT
= 1<<4, /* Bit 4: Remote Fault Condition Occured */
1039 PHY_ST_AN_CAP
= 1<<3, /* Bit 3: Auto-Negotiation Capability */
1040 PHY_ST_LSYNC
= 1<<2, /* Bit 2: Link Synchronized */
1041 PHY_ST_JAB_DET
= 1<<1, /* Bit 1: Jabber Detected */
1042 PHY_ST_EXT_REG
= 1<<0, /* Bit 0: Extended Register available */
1046 PHY_I1_OUI_MSK
= 0x3f<<10, /* Bit 15..10: Organization Unique ID */
1047 PHY_I1_MOD_NUM
= 0x3f<<4, /* Bit 9.. 4: Model Number */
1048 PHY_I1_REV_MSK
= 0xf, /* Bit 3.. 0: Revision Number */
1051 /* different Broadcom PHY Ids */
1053 PHY_BCOM_ID1_A1
= 0x6041,
1054 PHY_BCOM_ID1_B2
= 0x6043,
1055 PHY_BCOM_ID1_C0
= 0x6044,
1056 PHY_BCOM_ID1_C5
= 0x6047,
1059 /* different Marvell PHY Ids */
1061 PHY_MARV_ID0_VAL
= 0x0141, /* Marvell Unique Identifier */
1062 PHY_MARV_ID1_B0
= 0x0C23, /* Yukon (PHY 88E1011) */
1063 PHY_MARV_ID1_B2
= 0x0C25, /* Yukon-Plus (PHY 88E1011) */
1064 PHY_MARV_ID1_C2
= 0x0CC2, /* Yukon-EC (PHY 88E1111) */
1065 PHY_MARV_ID1_Y2
= 0x0C91, /* Yukon-2 (PHY 88E1112) */
1068 /* Advertisement register bits */
1070 PHY_AN_NXT_PG
= 1<<15, /* Bit 15: Request Next Page */
1071 PHY_AN_ACK
= 1<<14, /* Bit 14: (ro) Acknowledge Received */
1072 PHY_AN_RF
= 1<<13, /* Bit 13: Remote Fault Bits */
1074 PHY_AN_PAUSE_ASYM
= 1<<11,/* Bit 11: Try for asymmetric */
1075 PHY_AN_PAUSE_CAP
= 1<<10, /* Bit 10: Try for pause */
1076 PHY_AN_100BASE4
= 1<<9, /* Bit 9: Try for 100mbps 4k packets */
1077 PHY_AN_100FULL
= 1<<8, /* Bit 8: Try for 100mbps full-duplex */
1078 PHY_AN_100HALF
= 1<<7, /* Bit 7: Try for 100mbps half-duplex */
1079 PHY_AN_10FULL
= 1<<6, /* Bit 6: Try for 10mbps full-duplex */
1080 PHY_AN_10HALF
= 1<<5, /* Bit 5: Try for 10mbps half-duplex */
1081 PHY_AN_CSMA
= 1<<0, /* Bit 0: Only selector supported */
1082 PHY_AN_SEL
= 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
1083 PHY_AN_FULL
= PHY_AN_100FULL
| PHY_AN_10FULL
| PHY_AN_CSMA
,
1084 PHY_AN_ALL
= PHY_AN_10HALF
| PHY_AN_10FULL
|
1085 PHY_AN_100HALF
| PHY_AN_100FULL
,
1090 PHY_X_AN_NXT_PG
= 1<<15, /* Bit 15: Request Next Page */
1091 PHY_X_AN_ACK
= 1<<14, /* Bit 14: (ro) Acknowledge Received */
1092 PHY_X_AN_RFB
= 3<<12,/* Bit 13..12: Remote Fault Bits */
1094 PHY_X_AN_PAUSE
= 3<<7,/* Bit 8.. 7: Pause Bits */
1095 PHY_X_AN_HD
= 1<<6, /* Bit 6: Half Duplex */
1096 PHY_X_AN_FD
= 1<<5, /* Bit 5: Full Duplex */
1099 /* Pause Bits (PHY_X_AN_PAUSE and PHY_X_RS_PAUSE) encoding */
1101 PHY_X_P_NO_PAUSE
= 0<<7,/* Bit 8..7: no Pause Mode */
1102 PHY_X_P_SYM_MD
= 1<<7, /* Bit 8..7: symmetric Pause Mode */
1103 PHY_X_P_ASYM_MD
= 2<<7,/* Bit 8..7: asymmetric Pause Mode */
1104 PHY_X_P_BOTH_MD
= 3<<7,/* Bit 8..7: both Pause Mode */
1108 /***** PHY_XMAC_EXT_STAT 16 bit r/w Extended Status Register *****/
1110 PHY_X_EX_FD
= 1<<15, /* Bit 15: Device Supports Full Duplex */
1111 PHY_X_EX_HD
= 1<<14, /* Bit 14: Device Supports Half Duplex */
1114 /***** PHY_XMAC_RES_ABI 16 bit r/o PHY Resolved Ability *****/
1116 PHY_X_RS_PAUSE
= 3<<7, /* Bit 8..7: selected Pause Mode */
1117 PHY_X_RS_HD
= 1<<6, /* Bit 6: Half Duplex Mode selected */
1118 PHY_X_RS_FD
= 1<<5, /* Bit 5: Full Duplex Mode selected */
1119 PHY_X_RS_ABLMIS
= 1<<4, /* Bit 4: duplex or pause cap mismatch */
1120 PHY_X_RS_PAUMIS
= 1<<3, /* Bit 3: pause capability mismatch */
1123 /* Remote Fault Bits (PHY_X_AN_RFB) encoding */
1125 X_RFB_OK
= 0<<12,/* Bit 13..12 No errors, Link OK */
1126 X_RFB_LF
= 1<<12,/* Bit 13..12 Link Failure */
1127 X_RFB_OFF
= 2<<12,/* Bit 13..12 Offline */
1128 X_RFB_AN_ERR
= 3<<12,/* Bit 13..12 Auto-Negotiation Error */
1131 /* Broadcom-Specific */
1132 /***** PHY_BCOM_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
1134 PHY_B_1000C_TEST
= 7<<13,/* Bit 15..13: Test Modes */
1135 PHY_B_1000C_MSE
= 1<<12, /* Bit 12: Master/Slave Enable */
1136 PHY_B_1000C_MSC
= 1<<11, /* Bit 11: M/S Configuration */
1137 PHY_B_1000C_RD
= 1<<10, /* Bit 10: Repeater/DTE */
1138 PHY_B_1000C_AFD
= 1<<9, /* Bit 9: Advertise Full Duplex */
1139 PHY_B_1000C_AHD
= 1<<8, /* Bit 8: Advertise Half Duplex */
1142 /***** PHY_BCOM_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
1143 /***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
1145 PHY_B_1000S_MSF
= 1<<15, /* Bit 15: Master/Slave Fault */
1146 PHY_B_1000S_MSR
= 1<<14, /* Bit 14: Master/Slave Result */
1147 PHY_B_1000S_LRS
= 1<<13, /* Bit 13: Local Receiver Status */
1148 PHY_B_1000S_RRS
= 1<<12, /* Bit 12: Remote Receiver Status */
1149 PHY_B_1000S_LP_FD
= 1<<11, /* Bit 11: Link Partner can FD */
1150 PHY_B_1000S_LP_HD
= 1<<10, /* Bit 10: Link Partner can HD */
1151 /* Bit 9..8: reserved */
1152 PHY_B_1000S_IEC
= 0xff, /* Bit 7..0: Idle Error Count */
1155 /***** PHY_BCOM_EXT_STAT 16 bit r/o Extended Status Register *****/
1157 PHY_B_ES_X_FD_CAP
= 1<<15, /* Bit 15: 1000Base-X FD capable */
1158 PHY_B_ES_X_HD_CAP
= 1<<14, /* Bit 14: 1000Base-X HD capable */
1159 PHY_B_ES_T_FD_CAP
= 1<<13, /* Bit 13: 1000Base-T FD capable */
1160 PHY_B_ES_T_HD_CAP
= 1<<12, /* Bit 12: 1000Base-T HD capable */
1163 /***** PHY_BCOM_P_EXT_CTRL 16 bit r/w PHY Extended Control Reg *****/
1165 PHY_B_PEC_MAC_PHY
= 1<<15, /* Bit 15: 10BIT/GMI-Interface */
1166 PHY_B_PEC_DIS_CROSS
= 1<<14, /* Bit 14: Disable MDI Crossover */
1167 PHY_B_PEC_TX_DIS
= 1<<13, /* Bit 13: Tx output Disabled */
1168 PHY_B_PEC_INT_DIS
= 1<<12, /* Bit 12: Interrupts Disabled */
1169 PHY_B_PEC_F_INT
= 1<<11, /* Bit 11: Force Interrupt */
1170 PHY_B_PEC_BY_45
= 1<<10, /* Bit 10: Bypass 4B5B-Decoder */
1171 PHY_B_PEC_BY_SCR
= 1<<9, /* Bit 9: Bypass Scrambler */
1172 PHY_B_PEC_BY_MLT3
= 1<<8, /* Bit 8: Bypass MLT3 Encoder */
1173 PHY_B_PEC_BY_RXA
= 1<<7, /* Bit 7: Bypass Rx Alignm. */
1174 PHY_B_PEC_RES_SCR
= 1<<6, /* Bit 6: Reset Scrambler */
1175 PHY_B_PEC_EN_LTR
= 1<<5, /* Bit 5: Ena LED Traffic Mode */
1176 PHY_B_PEC_LED_ON
= 1<<4, /* Bit 4: Force LED's on */
1177 PHY_B_PEC_LED_OFF
= 1<<3, /* Bit 3: Force LED's off */
1178 PHY_B_PEC_EX_IPG
= 1<<2, /* Bit 2: Extend Tx IPG Mode */
1179 PHY_B_PEC_3_LED
= 1<<1, /* Bit 1: Three Link LED mode */
1180 PHY_B_PEC_HIGH_LA
= 1<<0, /* Bit 0: GMII FIFO Elasticy */
1183 /***** PHY_BCOM_P_EXT_STAT 16 bit r/o PHY Extended Status Reg *****/
1185 PHY_B_PES_CROSS_STAT
= 1<<13, /* Bit 13: MDI Crossover Status */
1186 PHY_B_PES_INT_STAT
= 1<<12, /* Bit 12: Interrupt Status */
1187 PHY_B_PES_RRS
= 1<<11, /* Bit 11: Remote Receiver Stat. */
1188 PHY_B_PES_LRS
= 1<<10, /* Bit 10: Local Receiver Stat. */
1189 PHY_B_PES_LOCKED
= 1<<9, /* Bit 9: Locked */
1190 PHY_B_PES_LS
= 1<<8, /* Bit 8: Link Status */
1191 PHY_B_PES_RF
= 1<<7, /* Bit 7: Remote Fault */
1192 PHY_B_PES_CE_ER
= 1<<6, /* Bit 6: Carrier Ext Error */
1193 PHY_B_PES_BAD_SSD
= 1<<5, /* Bit 5: Bad SSD */
1194 PHY_B_PES_BAD_ESD
= 1<<4, /* Bit 4: Bad ESD */
1195 PHY_B_PES_RX_ER
= 1<<3, /* Bit 3: Receive Error */
1196 PHY_B_PES_TX_ER
= 1<<2, /* Bit 2: Transmit Error */
1197 PHY_B_PES_LOCK_ER
= 1<<1, /* Bit 1: Lock Error */
1198 PHY_B_PES_MLT3_ER
= 1<<0, /* Bit 0: MLT3 code Error */
1201 /* PHY_BCOM_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/
1202 /* PHY_BCOM_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/
1204 PHY_B_AN_RF
= 1<<13, /* Bit 13: Remote Fault */
1206 PHY_B_AN_ASP
= 1<<11, /* Bit 11: Asymmetric Pause */
1207 PHY_B_AN_PC
= 1<<10, /* Bit 10: Pause Capable */
1211 /***** PHY_BCOM_FC_CTR 16 bit r/w False Carrier Counter *****/
1213 PHY_B_FC_CTR
= 0xff, /* Bit 7..0: False Carrier Counter */
1215 /***** PHY_BCOM_RNO_CTR 16 bit r/w Receive NOT_OK Counter *****/
1216 PHY_B_RC_LOC_MSK
= 0xff00, /* Bit 15..8: Local Rx NOT_OK cnt */
1217 PHY_B_RC_REM_MSK
= 0x00ff, /* Bit 7..0: Remote Rx NOT_OK cnt */
1219 /***** PHY_BCOM_AUX_CTRL 16 bit r/w Auxiliary Control Reg *****/
1220 PHY_B_AC_L_SQE
= 1<<15, /* Bit 15: Low Squelch */
1221 PHY_B_AC_LONG_PACK
= 1<<14, /* Bit 14: Rx Long Packets */
1222 PHY_B_AC_ER_CTRL
= 3<<12,/* Bit 13..12: Edgerate Control */
1223 /* Bit 11: reserved */
1224 PHY_B_AC_TX_TST
= 1<<10, /* Bit 10: Tx test bit, always 1 */
1225 /* Bit 9.. 8: reserved */
1226 PHY_B_AC_DIS_PRF
= 1<<7, /* Bit 7: dis part resp filter */
1227 /* Bit 6: reserved */
1228 PHY_B_AC_DIS_PM
= 1<<5, /* Bit 5: dis power management */
1229 /* Bit 4: reserved */
1230 PHY_B_AC_DIAG
= 1<<3, /* Bit 3: Diagnostic Mode */
1233 /***** PHY_BCOM_AUX_STAT 16 bit r/o Auxiliary Status Reg *****/
1235 PHY_B_AS_AN_C
= 1<<15, /* Bit 15: AutoNeg complete */
1236 PHY_B_AS_AN_CA
= 1<<14, /* Bit 14: AN Complete Ack */
1237 PHY_B_AS_ANACK_D
= 1<<13, /* Bit 13: AN Ack Detect */
1238 PHY_B_AS_ANAB_D
= 1<<12, /* Bit 12: AN Ability Detect */
1239 PHY_B_AS_NPW
= 1<<11, /* Bit 11: AN Next Page Wait */
1240 PHY_B_AS_AN_RES_MSK
= 7<<8,/* Bit 10..8: AN HDC */
1241 PHY_B_AS_PDF
= 1<<7, /* Bit 7: Parallel Detect. Fault */
1242 PHY_B_AS_RF
= 1<<6, /* Bit 6: Remote Fault */
1243 PHY_B_AS_ANP_R
= 1<<5, /* Bit 5: AN Page Received */
1244 PHY_B_AS_LP_ANAB
= 1<<4, /* Bit 4: LP AN Ability */
1245 PHY_B_AS_LP_NPAB
= 1<<3, /* Bit 3: LP Next Page Ability */
1246 PHY_B_AS_LS
= 1<<2, /* Bit 2: Link Status */
1247 PHY_B_AS_PRR
= 1<<1, /* Bit 1: Pause Resolution-Rx */
1248 PHY_B_AS_PRT
= 1<<0, /* Bit 0: Pause Resolution-Tx */
1250 #define PHY_B_AS_PAUSE_MSK (PHY_B_AS_PRR | PHY_B_AS_PRT)
1252 /***** PHY_BCOM_INT_STAT 16 bit r/o Interrupt Status Reg *****/
1253 /***** PHY_BCOM_INT_MASK 16 bit r/w Interrupt Mask Reg *****/
1255 PHY_B_IS_PSE
= 1<<14, /* Bit 14: Pair Swap Error */
1256 PHY_B_IS_MDXI_SC
= 1<<13, /* Bit 13: MDIX Status Change */
1257 PHY_B_IS_HCT
= 1<<12, /* Bit 12: counter above 32k */
1258 PHY_B_IS_LCT
= 1<<11, /* Bit 11: counter above 128 */
1259 PHY_B_IS_AN_PR
= 1<<10, /* Bit 10: Page Received */
1260 PHY_B_IS_NO_HDCL
= 1<<9, /* Bit 9: No HCD Link */
1261 PHY_B_IS_NO_HDC
= 1<<8, /* Bit 8: No HCD */
1262 PHY_B_IS_NEG_USHDC
= 1<<7, /* Bit 7: Negotiated Unsup. HCD */
1263 PHY_B_IS_SCR_S_ER
= 1<<6, /* Bit 6: Scrambler Sync Error */
1264 PHY_B_IS_RRS_CHANGE
= 1<<5, /* Bit 5: Remote Rx Stat Change */
1265 PHY_B_IS_LRS_CHANGE
= 1<<4, /* Bit 4: Local Rx Stat Change */
1266 PHY_B_IS_DUP_CHANGE
= 1<<3, /* Bit 3: Duplex Mode Change */
1267 PHY_B_IS_LSP_CHANGE
= 1<<2, /* Bit 2: Link Speed Change */
1268 PHY_B_IS_LST_CHANGE
= 1<<1, /* Bit 1: Link Status Changed */
1269 PHY_B_IS_CRC_ER
= 1<<0, /* Bit 0: CRC Error */
1271 #define PHY_B_DEF_MSK \
1272 (~(PHY_B_IS_PSE | PHY_B_IS_AN_PR | PHY_B_IS_DUP_CHANGE | \
1273 PHY_B_IS_LSP_CHANGE | PHY_B_IS_LST_CHANGE))
1275 /* Pause Bits (PHY_B_AN_ASP and PHY_B_AN_PC) encoding */
1277 PHY_B_P_NO_PAUSE
= 0<<10,/* Bit 11..10: no Pause Mode */
1278 PHY_B_P_SYM_MD
= 1<<10, /* Bit 11..10: symmetric Pause Mode */
1279 PHY_B_P_ASYM_MD
= 2<<10,/* Bit 11..10: asymmetric Pause Mode */
1280 PHY_B_P_BOTH_MD
= 3<<10,/* Bit 11..10: both Pause Mode */
1283 * Resolved Duplex mode and Capabilities (Aux Status Summary Reg)
1286 PHY_B_RES_1000FD
= 7<<8,/* Bit 10..8: 1000Base-T Full Dup. */
1287 PHY_B_RES_1000HD
= 6<<8,/* Bit 10..8: 1000Base-T Half Dup. */
1290 /** Marvell-Specific */
1292 PHY_M_AN_NXT_PG
= 1<<15, /* Request Next Page */
1293 PHY_M_AN_ACK
= 1<<14, /* (ro) Acknowledge Received */
1294 PHY_M_AN_RF
= 1<<13, /* Remote Fault */
1296 PHY_M_AN_ASP
= 1<<11, /* Asymmetric Pause */
1297 PHY_M_AN_PC
= 1<<10, /* MAC Pause implemented */
1298 PHY_M_AN_100_T4
= 1<<9, /* Not cap. 100Base-T4 (always 0) */
1299 PHY_M_AN_100_FD
= 1<<8, /* Advertise 100Base-TX Full Duplex */
1300 PHY_M_AN_100_HD
= 1<<7, /* Advertise 100Base-TX Half Duplex */
1301 PHY_M_AN_10_FD
= 1<<6, /* Advertise 10Base-TX Full Duplex */
1302 PHY_M_AN_10_HD
= 1<<5, /* Advertise 10Base-TX Half Duplex */
1303 PHY_M_AN_SEL_MSK
=0x1f<<4, /* Bit 4.. 0: Selector Field Mask */
1306 /* special defines for FIBER (88E1011S only) */
1308 PHY_M_AN_ASP_X
= 1<<8, /* Asymmetric Pause */
1309 PHY_M_AN_PC_X
= 1<<7, /* MAC Pause implemented */
1310 PHY_M_AN_1000X_AHD
= 1<<6, /* Advertise 10000Base-X Half Duplex */
1311 PHY_M_AN_1000X_AFD
= 1<<5, /* Advertise 10000Base-X Full Duplex */
1314 /* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */
1316 PHY_M_P_NO_PAUSE_X
= 0<<7,/* Bit 8.. 7: no Pause Mode */
1317 PHY_M_P_SYM_MD_X
= 1<<7, /* Bit 8.. 7: symmetric Pause Mode */
1318 PHY_M_P_ASYM_MD_X
= 2<<7,/* Bit 8.. 7: asymmetric Pause Mode */
1319 PHY_M_P_BOTH_MD_X
= 3<<7,/* Bit 8.. 7: both Pause Mode */
1322 /***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
1324 PHY_M_1000C_TEST
= 7<<13,/* Bit 15..13: Test Modes */
1325 PHY_M_1000C_MSE
= 1<<12, /* Manual Master/Slave Enable */
1326 PHY_M_1000C_MSC
= 1<<11, /* M/S Configuration (1=Master) */
1327 PHY_M_1000C_MPD
= 1<<10, /* Multi-Port Device */
1328 PHY_M_1000C_AFD
= 1<<9, /* Advertise Full Duplex */
1329 PHY_M_1000C_AHD
= 1<<8, /* Advertise Half Duplex */
1332 /***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/
1334 PHY_M_PC_TX_FFD_MSK
= 3<<14,/* Bit 15..14: Tx FIFO Depth Mask */
1335 PHY_M_PC_RX_FFD_MSK
= 3<<12,/* Bit 13..12: Rx FIFO Depth Mask */
1336 PHY_M_PC_ASS_CRS_TX
= 1<<11, /* Assert CRS on Transmit */
1337 PHY_M_PC_FL_GOOD
= 1<<10, /* Force Link Good */
1338 PHY_M_PC_EN_DET_MSK
= 3<<8,/* Bit 9.. 8: Energy Detect Mask */
1339 PHY_M_PC_ENA_EXT_D
= 1<<7, /* Enable Ext. Distance (10BT) */
1340 PHY_M_PC_MDIX_MSK
= 3<<5,/* Bit 6.. 5: MDI/MDIX Config. Mask */
1341 PHY_M_PC_DIS_125CLK
= 1<<4, /* Disable 125 CLK */
1342 PHY_M_PC_MAC_POW_UP
= 1<<3, /* MAC Power up */
1343 PHY_M_PC_SQE_T_ENA
= 1<<2, /* SQE Test Enabled */
1344 PHY_M_PC_POL_R_DIS
= 1<<1, /* Polarity Reversal Disabled */
1345 PHY_M_PC_DIS_JABBER
= 1<<0, /* Disable Jabber */
1349 PHY_M_PC_EN_DET
= 2<<8, /* Energy Detect (Mode 1) */
1350 PHY_M_PC_EN_DET_PLUS
= 3<<8, /* Energy Detect Plus (Mode 2) */
1353 #define PHY_M_PC_MDI_XMODE(x) ((((u16)(x)<<5) & PHY_M_PC_MDIX_MSK)
1356 PHY_M_PC_MAN_MDI
= 0, /* 00 = Manual MDI configuration */
1357 PHY_M_PC_MAN_MDIX
= 1, /* 01 = Manual MDIX configuration */
1358 PHY_M_PC_ENA_AUTO
= 3, /* 11 = Enable Automatic Crossover */
1361 /* for 10/100 Fast Ethernet PHY (88E3082 only) */
1363 PHY_M_PC_ENA_DTE_DT
= 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
1364 PHY_M_PC_ENA_ENE_DT
= 1<<14, /* Enable Energy Detect (sense & pulse) */
1365 PHY_M_PC_DIS_NLP_CK
= 1<<13, /* Disable Normal Link Puls (NLP) Check */
1366 PHY_M_PC_ENA_LIP_NP
= 1<<12, /* Enable Link Partner Next Page Reg. */
1367 PHY_M_PC_DIS_NLP_GN
= 1<<11, /* Disable Normal Link Puls Generation */
1369 PHY_M_PC_DIS_SCRAMB
= 1<<9, /* Disable Scrambler */
1370 PHY_M_PC_DIS_FEFI
= 1<<8, /* Disable Far End Fault Indic. (FEFI) */
1372 PHY_M_PC_SH_TP_SEL
= 1<<6, /* Shielded Twisted Pair Select */
1373 PHY_M_PC_RX_FD_MSK
= 3<<2,/* Bit 3.. 2: Rx FIFO Depth Mask */
1376 /***** PHY_MARV_PHY_STAT 16 bit r/o PHY Specific Status Reg *****/
1378 PHY_M_PS_SPEED_MSK
= 3<<14, /* Bit 15..14: Speed Mask */
1379 PHY_M_PS_SPEED_1000
= 1<<15, /* 10 = 1000 Mbps */
1380 PHY_M_PS_SPEED_100
= 1<<14, /* 01 = 100 Mbps */
1381 PHY_M_PS_SPEED_10
= 0, /* 00 = 10 Mbps */
1382 PHY_M_PS_FULL_DUP
= 1<<13, /* Full Duplex */
1383 PHY_M_PS_PAGE_REC
= 1<<12, /* Page Received */
1384 PHY_M_PS_SPDUP_RES
= 1<<11, /* Speed & Duplex Resolved */
1385 PHY_M_PS_LINK_UP
= 1<<10, /* Link Up */
1386 PHY_M_PS_CABLE_MSK
= 7<<7, /* Bit 9.. 7: Cable Length Mask */
1387 PHY_M_PS_MDI_X_STAT
= 1<<6, /* MDI Crossover Stat (1=MDIX) */
1388 PHY_M_PS_DOWNS_STAT
= 1<<5, /* Downshift Status (1=downsh.) */
1389 PHY_M_PS_ENDET_STAT
= 1<<4, /* Energy Detect Status (1=act) */
1390 PHY_M_PS_TX_P_EN
= 1<<3, /* Tx Pause Enabled */
1391 PHY_M_PS_RX_P_EN
= 1<<2, /* Rx Pause Enabled */
1392 PHY_M_PS_POL_REV
= 1<<1, /* Polarity Reversed */
1393 PHY_M_PS_JABBER
= 1<<0, /* Jabber */
1396 #define PHY_M_PS_PAUSE_MSK (PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN)
1398 /* for 10/100 Fast Ethernet PHY (88E3082 only) */
1400 PHY_M_PS_DTE_DETECT
= 1<<15, /* Data Terminal Equipment (DTE) Detected */
1401 PHY_M_PS_RES_SPEED
= 1<<14, /* Resolved Speed (1=100 Mbps, 0=10 Mbps */
1405 PHY_M_IS_AN_ERROR
= 1<<15, /* Auto-Negotiation Error */
1406 PHY_M_IS_LSP_CHANGE
= 1<<14, /* Link Speed Changed */
1407 PHY_M_IS_DUP_CHANGE
= 1<<13, /* Duplex Mode Changed */
1408 PHY_M_IS_AN_PR
= 1<<12, /* Page Received */
1409 PHY_M_IS_AN_COMPL
= 1<<11, /* Auto-Negotiation Completed */
1410 PHY_M_IS_LST_CHANGE
= 1<<10, /* Link Status Changed */
1411 PHY_M_IS_SYMB_ERROR
= 1<<9, /* Symbol Error */
1412 PHY_M_IS_FALSE_CARR
= 1<<8, /* False Carrier */
1413 PHY_M_IS_FIFO_ERROR
= 1<<7, /* FIFO Overflow/Underrun Error */
1414 PHY_M_IS_MDI_CHANGE
= 1<<6, /* MDI Crossover Changed */
1415 PHY_M_IS_DOWNSH_DET
= 1<<5, /* Downshift Detected */
1416 PHY_M_IS_END_CHANGE
= 1<<4, /* Energy Detect Changed */
1418 PHY_M_IS_DTE_CHANGE
= 1<<2, /* DTE Power Det. Status Changed */
1419 PHY_M_IS_POL_CHANGE
= 1<<1, /* Polarity Changed */
1420 PHY_M_IS_JABBER
= 1<<0, /* Jabber */
1422 PHY_M_IS_DEF_MSK
= PHY_M_IS_AN_ERROR
| PHY_M_IS_LSP_CHANGE
|
1423 PHY_M_IS_LST_CHANGE
| PHY_M_IS_FIFO_ERROR
,
1425 PHY_M_IS_AN_MSK
= PHY_M_IS_AN_ERROR
| PHY_M_IS_AN_COMPL
,
1428 /***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/
1430 PHY_M_EC_ENA_BC_EXT
= 1<<15, /* Enable Block Carr. Ext. (88E1111 only) */
1431 PHY_M_EC_ENA_LIN_LB
= 1<<14, /* Enable Line Loopback (88E1111 only) */
1433 PHY_M_EC_DIS_LINK_P
= 1<<12, /* Disable Link Pulses (88E1111 only) */
1434 PHY_M_EC_M_DSC_MSK
= 3<<10, /* Bit 11..10: Master Downshift Counter */
1435 /* (88E1011 only) */
1436 PHY_M_EC_S_DSC_MSK
= 3<<8, /* Bit 9.. 8: Slave Downshift Counter */
1437 /* (88E1011 only) */
1438 PHY_M_EC_M_DSC_MSK2
= 7<<9, /* Bit 11.. 9: Master Downshift Counter */
1439 /* (88E1111 only) */
1440 PHY_M_EC_DOWN_S_ENA
= 1<<8, /* Downshift Enable (88E1111 only) */
1441 /* !!! Errata in spec. (1 = disable) */
1442 PHY_M_EC_RX_TIM_CT
= 1<<7, /* RGMII Rx Timing Control*/
1443 PHY_M_EC_MAC_S_MSK
= 7<<4, /* Bit 6.. 4: Def. MAC interface speed */
1444 PHY_M_EC_FIB_AN_ENA
= 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */
1445 PHY_M_EC_DTE_D_ENA
= 1<<2, /* DTE Detect Enable (88E1111 only) */
1446 PHY_M_EC_TX_TIM_CT
= 1<<1, /* RGMII Tx Timing Control */
1447 PHY_M_EC_TRANS_DIS
= 1<<0, /* Transmitter Disable (88E1111 only) */};
1449 #define PHY_M_EC_M_DSC(x) ((u16)(x)<<10) /* 00=1x; 01=2x; 10=3x; 11=4x */
1450 #define PHY_M_EC_S_DSC(x) ((u16)(x)<<8) /* 00=dis; 01=1x; 10=2x; 11=3x */
1451 #define PHY_M_EC_MAC_S(x) ((u16)(x)<<4) /* 01X=0; 110=2.5; 111=25 (MHz) */
1453 #define PHY_M_EC_M_DSC_2(x) ((u16)(x)<<9) /* 000=1x; 001=2x; 010=3x; 011=4x */
1454 /* 100=5x; 101=6x; 110=7x; 111=8x */
1456 MAC_TX_CLK_0_MHZ
= 2,
1457 MAC_TX_CLK_2_5_MHZ
= 6,
1458 MAC_TX_CLK_25_MHZ
= 7,
1461 /***** PHY_MARV_LED_CTRL 16 bit r/w LED Control Reg *****/
1463 PHY_M_LEDC_DIS_LED
= 1<<15, /* Disable LED */
1464 PHY_M_LEDC_PULS_MSK
= 7<<12,/* Bit 14..12: Pulse Stretch Mask */
1465 PHY_M_LEDC_F_INT
= 1<<11, /* Force Interrupt */
1466 PHY_M_LEDC_BL_R_MSK
= 7<<8,/* Bit 10.. 8: Blink Rate Mask */
1467 PHY_M_LEDC_DP_C_LSB
= 1<<7, /* Duplex Control (LSB, 88E1111 only) */
1468 PHY_M_LEDC_TX_C_LSB
= 1<<6, /* Tx Control (LSB, 88E1111 only) */
1469 PHY_M_LEDC_LK_C_MSK
= 7<<3,/* Bit 5.. 3: Link Control Mask */
1470 /* (88E1111 only) */
1472 #define PHY_M_LED_PULS_DUR(x) (((u16)(x)<<12) & PHY_M_LEDC_PULS_MSK)
1473 #define PHY_M_LED_BLINK_RT(x) (((u16)(x)<<8) & PHY_M_LEDC_BL_R_MSK)
1476 PHY_M_LEDC_LINK_MSK
= 3<<3, /* Bit 4.. 3: Link Control Mask */
1477 /* (88E1011 only) */
1478 PHY_M_LEDC_DP_CTRL
= 1<<2, /* Duplex Control */
1479 PHY_M_LEDC_DP_C_MSB
= 1<<2, /* Duplex Control (MSB, 88E1111 only) */
1480 PHY_M_LEDC_RX_CTRL
= 1<<1, /* Rx Activity / Link */
1481 PHY_M_LEDC_TX_CTRL
= 1<<0, /* Tx Activity / Link */
1482 PHY_M_LEDC_TX_C_MSB
= 1<<0, /* Tx Control (MSB, 88E1111 only) */
1486 PULS_NO_STR
= 0, /* no pulse stretching */
1487 PULS_21MS
= 1, /* 21 ms to 42 ms */
1488 PULS_42MS
= 2, /* 42 ms to 84 ms */
1489 PULS_84MS
= 3, /* 84 ms to 170 ms */
1490 PULS_170MS
= 4, /* 170 ms to 340 ms */
1491 PULS_340MS
= 5, /* 340 ms to 670 ms */
1492 PULS_670MS
= 6, /* 670 ms to 1.3 s */
1493 PULS_1300MS
= 7, /* 1.3 s to 2.7 s */
1498 BLINK_42MS
= 0, /* 42 ms */
1499 BLINK_84MS
= 1, /* 84 ms */
1500 BLINK_170MS
= 2, /* 170 ms */
1501 BLINK_340MS
= 3, /* 340 ms */
1502 BLINK_670MS
= 4, /* 670 ms */
1505 /***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
1506 #define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
1507 /* Bit 13..12: reserved */
1508 #define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
1509 #define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
1510 #define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
1511 #define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
1512 #define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
1513 #define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
1522 /***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
1524 PHY_M_EC2_FI_IMPED
= 1<<6, /* Fiber Input Impedance */
1525 PHY_M_EC2_FO_IMPED
= 1<<5, /* Fiber Output Impedance */
1526 PHY_M_EC2_FO_M_CLK
= 1<<4, /* Fiber Mode Clock Enable */
1527 PHY_M_EC2_FO_BOOST
= 1<<3, /* Fiber Output Boost */
1528 PHY_M_EC2_FO_AM_MSK
= 7, /* Bit 2.. 0: Fiber Output Amplitude */
1531 /***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/
1533 PHY_M_FC_AUTO_SEL
= 1<<15, /* Fiber/Copper Auto Sel. Dis. */
1534 PHY_M_FC_AN_REG_ACC
= 1<<14, /* Fiber/Copper AN Reg. Access */
1535 PHY_M_FC_RESOLUTION
= 1<<13, /* Fiber/Copper Resolution */
1536 PHY_M_SER_IF_AN_BP
= 1<<12, /* Ser. IF AN Bypass Enable */
1537 PHY_M_SER_IF_BP_ST
= 1<<11, /* Ser. IF AN Bypass Status */
1538 PHY_M_IRQ_POLARITY
= 1<<10, /* IRQ polarity */
1539 PHY_M_DIS_AUT_MED
= 1<<9, /* Disable Aut. Medium Reg. Selection */
1540 /* (88E1111 only) */
1541 /* Bit 9.. 4: reserved (88E1011 only) */
1542 PHY_M_UNDOC1
= 1<<7, /* undocumented bit !! */
1543 PHY_M_DTE_POW_STAT
= 1<<4, /* DTE Power Status (88E1111 only) */
1544 PHY_M_MODE_MASK
= 0xf, /* Bit 3.. 0: copy of HWCFG MODE[3:0] */
1547 /***** PHY_MARV_CABLE_DIAG 16 bit r/o Cable Diagnostic Reg *****/
1549 PHY_M_CABD_ENA_TEST
= 1<<15, /* Enable Test (Page 0) */
1550 PHY_M_CABD_DIS_WAIT
= 1<<15, /* Disable Waiting Period (Page 1) */
1551 /* (88E1111 only) */
1552 PHY_M_CABD_STAT_MSK
= 3<<13, /* Bit 14..13: Status Mask */
1553 PHY_M_CABD_AMPL_MSK
= 0x1f<<8, /* Bit 12.. 8: Amplitude Mask */
1554 /* (88E1111 only) */
1555 PHY_M_CABD_DIST_MSK
= 0xff, /* Bit 7.. 0: Distance Mask */
1558 /* values for Cable Diagnostic Status (11=fail; 00=OK; 10=open; 01=short) */
1560 CABD_STAT_NORMAL
= 0,
1561 CABD_STAT_SHORT
= 1,
1566 /* for 10/100 Fast Ethernet PHY (88E3082 only) */
1567 /***** PHY_MARV_FE_LED_PAR 16 bit r/w LED Parallel Select Reg. *****/
1568 /* Bit 15..12: reserved (used internally) */
1570 PHY_M_FELP_LED2_MSK
= 0xf<<8, /* Bit 11.. 8: LED2 Mask (LINK) */
1571 PHY_M_FELP_LED1_MSK
= 0xf<<4, /* Bit 7.. 4: LED1 Mask (ACT) */
1572 PHY_M_FELP_LED0_MSK
= 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */
1575 #define PHY_M_FELP_LED2_CTRL(x) (((x)<<8) & PHY_M_FELP_LED2_MSK)
1576 #define PHY_M_FELP_LED1_CTRL(x) (((x)<<4) & PHY_M_FELP_LED1_MSK)
1577 #define PHY_M_FELP_LED0_CTRL(x) (((x)<<0) & PHY_M_FELP_LED0_MSK)
1580 LED_PAR_CTRL_COLX
= 0x00,
1581 LED_PAR_CTRL_ERROR
= 0x01,
1582 LED_PAR_CTRL_DUPLEX
= 0x02,
1583 LED_PAR_CTRL_DP_COL
= 0x03,
1584 LED_PAR_CTRL_SPEED
= 0x04,
1585 LED_PAR_CTRL_LINK
= 0x05,
1586 LED_PAR_CTRL_TX
= 0x06,
1587 LED_PAR_CTRL_RX
= 0x07,
1588 LED_PAR_CTRL_ACT
= 0x08,
1589 LED_PAR_CTRL_LNK_RX
= 0x09,
1590 LED_PAR_CTRL_LNK_AC
= 0x0a,
1591 LED_PAR_CTRL_ACT_BL
= 0x0b,
1592 LED_PAR_CTRL_TX_BL
= 0x0c,
1593 LED_PAR_CTRL_RX_BL
= 0x0d,
1594 LED_PAR_CTRL_COL_BL
= 0x0e,
1595 LED_PAR_CTRL_INACT
= 0x0f
1598 /*****,PHY_MARV_FE_SPEC_2 16 bit r/w Specific Control Reg. 2 *****/
1600 PHY_M_FESC_DIS_WAIT
= 1<<2, /* Disable TDR Waiting Period */
1601 PHY_M_FESC_ENA_MCLK
= 1<<1, /* Enable MAC Rx Clock in sleep mode */
1602 PHY_M_FESC_SEL_CL_A
= 1<<0, /* Select Class A driver (100B-TX) */
1606 /***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/
1608 PHY_M_LEDC_LOS_MSK
= 0xf<<12, /* Bit 15..12: LOS LED Ctrl. Mask */
1609 PHY_M_LEDC_INIT_MSK
= 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */
1610 PHY_M_LEDC_STA1_MSK
= 0xf<<4, /* Bit 7.. 4: STAT1 LED Ctrl. Mask */
1611 PHY_M_LEDC_STA0_MSK
= 0xf, /* Bit 3.. 0: STAT0 LED Ctrl. Mask */
1614 #define PHY_M_LEDC_LOS_CTRL(x) (((x)<<12) & PHY_M_LEDC_LOS_MSK)
1615 #define PHY_M_LEDC_INIT_CTRL(x) (((x)<<8) & PHY_M_LEDC_INIT_MSK)
1616 #define PHY_M_LEDC_STA1_CTRL(x) (((x)<<4) & PHY_M_LEDC_STA1_MSK)
1617 #define PHY_M_LEDC_STA0_CTRL(x) (((x)<<0) & PHY_M_LEDC_STA0_MSK)
1619 /* GMAC registers */
1620 /* Port Registers */
1622 GM_GP_STAT
= 0x0000, /* 16 bit r/o General Purpose Status */
1623 GM_GP_CTRL
= 0x0004, /* 16 bit r/w General Purpose Control */
1624 GM_TX_CTRL
= 0x0008, /* 16 bit r/w Transmit Control Reg. */
1625 GM_RX_CTRL
= 0x000c, /* 16 bit r/w Receive Control Reg. */
1626 GM_TX_FLOW_CTRL
= 0x0010, /* 16 bit r/w Transmit Flow-Control */
1627 GM_TX_PARAM
= 0x0014, /* 16 bit r/w Transmit Parameter Reg. */
1628 GM_SERIAL_MODE
= 0x0018, /* 16 bit r/w Serial Mode Register */
1629 /* Source Address Registers */
1630 GM_SRC_ADDR_1L
= 0x001c, /* 16 bit r/w Source Address 1 (low) */
1631 GM_SRC_ADDR_1M
= 0x0020, /* 16 bit r/w Source Address 1 (middle) */
1632 GM_SRC_ADDR_1H
= 0x0024, /* 16 bit r/w Source Address 1 (high) */
1633 GM_SRC_ADDR_2L
= 0x0028, /* 16 bit r/w Source Address 2 (low) */
1634 GM_SRC_ADDR_2M
= 0x002c, /* 16 bit r/w Source Address 2 (middle) */
1635 GM_SRC_ADDR_2H
= 0x0030, /* 16 bit r/w Source Address 2 (high) */
1637 /* Multicast Address Hash Registers */
1638 GM_MC_ADDR_H1
= 0x0034, /* 16 bit r/w Multicast Address Hash 1 */
1639 GM_MC_ADDR_H2
= 0x0038, /* 16 bit r/w Multicast Address Hash 2 */
1640 GM_MC_ADDR_H3
= 0x003c, /* 16 bit r/w Multicast Address Hash 3 */
1641 GM_MC_ADDR_H4
= 0x0040, /* 16 bit r/w Multicast Address Hash 4 */
1643 /* Interrupt Source Registers */
1644 GM_TX_IRQ_SRC
= 0x0044, /* 16 bit r/o Tx Overflow IRQ Source */
1645 GM_RX_IRQ_SRC
= 0x0048, /* 16 bit r/o Rx Overflow IRQ Source */
1646 GM_TR_IRQ_SRC
= 0x004c, /* 16 bit r/o Tx/Rx Over. IRQ Source */
1648 /* Interrupt Mask Registers */
1649 GM_TX_IRQ_MSK
= 0x0050, /* 16 bit r/w Tx Overflow IRQ Mask */
1650 GM_RX_IRQ_MSK
= 0x0054, /* 16 bit r/w Rx Overflow IRQ Mask */
1651 GM_TR_IRQ_MSK
= 0x0058, /* 16 bit r/w Tx/Rx Over. IRQ Mask */
1653 /* Serial Management Interface (SMI) Registers */
1654 GM_SMI_CTRL
= 0x0080, /* 16 bit r/w SMI Control Register */
1655 GM_SMI_DATA
= 0x0084, /* 16 bit r/w SMI Data Register */
1656 GM_PHY_ADDR
= 0x0088, /* 16 bit r/w GPHY Address Register */
1660 #define GM_MIB_CNT_BASE 0x0100 /* Base Address of MIB Counters */
1661 #define GM_MIB_CNT_SIZE 44 /* Number of MIB Counters */
1664 * MIB Counters base address definitions (low word) -
1665 * use offset 4 for access to high word (32 bit r/o)
1668 GM_RXF_UC_OK
= GM_MIB_CNT_BASE
+ 0, /* Unicast Frames Received OK */
1669 GM_RXF_BC_OK
= GM_MIB_CNT_BASE
+ 8, /* Broadcast Frames Received OK */
1670 GM_RXF_MPAUSE
= GM_MIB_CNT_BASE
+ 16, /* Pause MAC Ctrl Frames Received */
1671 GM_RXF_MC_OK
= GM_MIB_CNT_BASE
+ 24, /* Multicast Frames Received OK */
1672 GM_RXF_FCS_ERR
= GM_MIB_CNT_BASE
+ 32, /* Rx Frame Check Seq. Error */
1673 /* GM_MIB_CNT_BASE + 40: reserved */
1674 GM_RXO_OK_LO
= GM_MIB_CNT_BASE
+ 48, /* Octets Received OK Low */
1675 GM_RXO_OK_HI
= GM_MIB_CNT_BASE
+ 56, /* Octets Received OK High */
1676 GM_RXO_ERR_LO
= GM_MIB_CNT_BASE
+ 64, /* Octets Received Invalid Low */
1677 GM_RXO_ERR_HI
= GM_MIB_CNT_BASE
+ 72, /* Octets Received Invalid High */
1678 GM_RXF_SHT
= GM_MIB_CNT_BASE
+ 80, /* Frames <64 Byte Received OK */
1679 GM_RXE_FRAG
= GM_MIB_CNT_BASE
+ 88, /* Frames <64 Byte Received with FCS Err */
1680 GM_RXF_64B
= GM_MIB_CNT_BASE
+ 96, /* 64 Byte Rx Frame */
1681 GM_RXF_127B
= GM_MIB_CNT_BASE
+ 104, /* 65-127 Byte Rx Frame */
1682 GM_RXF_255B
= GM_MIB_CNT_BASE
+ 112, /* 128-255 Byte Rx Frame */
1683 GM_RXF_511B
= GM_MIB_CNT_BASE
+ 120, /* 256-511 Byte Rx Frame */
1684 GM_RXF_1023B
= GM_MIB_CNT_BASE
+ 128, /* 512-1023 Byte Rx Frame */
1685 GM_RXF_1518B
= GM_MIB_CNT_BASE
+ 136, /* 1024-1518 Byte Rx Frame */
1686 GM_RXF_MAX_SZ
= GM_MIB_CNT_BASE
+ 144, /* 1519-MaxSize Byte Rx Frame */
1687 GM_RXF_LNG_ERR
= GM_MIB_CNT_BASE
+ 152, /* Rx Frame too Long Error */
1688 GM_RXF_JAB_PKT
= GM_MIB_CNT_BASE
+ 160, /* Rx Jabber Packet Frame */
1689 /* GM_MIB_CNT_BASE + 168: reserved */
1690 GM_RXE_FIFO_OV
= GM_MIB_CNT_BASE
+ 176, /* Rx FIFO overflow Event */
1691 /* GM_MIB_CNT_BASE + 184: reserved */
1692 GM_TXF_UC_OK
= GM_MIB_CNT_BASE
+ 192, /* Unicast Frames Xmitted OK */
1693 GM_TXF_BC_OK
= GM_MIB_CNT_BASE
+ 200, /* Broadcast Frames Xmitted OK */
1694 GM_TXF_MPAUSE
= GM_MIB_CNT_BASE
+ 208, /* Pause MAC Ctrl Frames Xmitted */
1695 GM_TXF_MC_OK
= GM_MIB_CNT_BASE
+ 216, /* Multicast Frames Xmitted OK */
1696 GM_TXO_OK_LO
= GM_MIB_CNT_BASE
+ 224, /* Octets Transmitted OK Low */
1697 GM_TXO_OK_HI
= GM_MIB_CNT_BASE
+ 232, /* Octets Transmitted OK High */
1698 GM_TXF_64B
= GM_MIB_CNT_BASE
+ 240, /* 64 Byte Tx Frame */
1699 GM_TXF_127B
= GM_MIB_CNT_BASE
+ 248, /* 65-127 Byte Tx Frame */
1700 GM_TXF_255B
= GM_MIB_CNT_BASE
+ 256, /* 128-255 Byte Tx Frame */
1701 GM_TXF_511B
= GM_MIB_CNT_BASE
+ 264, /* 256-511 Byte Tx Frame */
1702 GM_TXF_1023B
= GM_MIB_CNT_BASE
+ 272, /* 512-1023 Byte Tx Frame */
1703 GM_TXF_1518B
= GM_MIB_CNT_BASE
+ 280, /* 1024-1518 Byte Tx Frame */
1704 GM_TXF_MAX_SZ
= GM_MIB_CNT_BASE
+ 288, /* 1519-MaxSize Byte Tx Frame */
1706 GM_TXF_COL
= GM_MIB_CNT_BASE
+ 304, /* Tx Collision */
1707 GM_TXF_LAT_COL
= GM_MIB_CNT_BASE
+ 312, /* Tx Late Collision */
1708 GM_TXF_ABO_COL
= GM_MIB_CNT_BASE
+ 320, /* Tx aborted due to Exces. Col. */
1709 GM_TXF_MUL_COL
= GM_MIB_CNT_BASE
+ 328, /* Tx Multiple Collision */
1710 GM_TXF_SNG_COL
= GM_MIB_CNT_BASE
+ 336, /* Tx Single Collision */
1711 GM_TXE_FIFO_UR
= GM_MIB_CNT_BASE
+ 344, /* Tx FIFO Underrun Event */
1714 /* GMAC Bit Definitions */
1715 /* GM_GP_STAT 16 bit r/o General Purpose Status Register */
1717 GM_GPSR_SPEED
= 1<<15, /* Bit 15: Port Speed (1 = 100 Mbps) */
1718 GM_GPSR_DUPLEX
= 1<<14, /* Bit 14: Duplex Mode (1 = Full) */
1719 GM_GPSR_FC_TX_DIS
= 1<<13, /* Bit 13: Tx Flow-Control Mode Disabled */
1720 GM_GPSR_LINK_UP
= 1<<12, /* Bit 12: Link Up Status */
1721 GM_GPSR_PAUSE
= 1<<11, /* Bit 11: Pause State */
1722 GM_GPSR_TX_ACTIVE
= 1<<10, /* Bit 10: Tx in Progress */
1723 GM_GPSR_EXC_COL
= 1<<9, /* Bit 9: Excessive Collisions Occured */
1724 GM_GPSR_LAT_COL
= 1<<8, /* Bit 8: Late Collisions Occured */
1726 GM_GPSR_PHY_ST_CH
= 1<<5, /* Bit 5: PHY Status Change */
1727 GM_GPSR_GIG_SPEED
= 1<<4, /* Bit 4: Gigabit Speed (1 = 1000 Mbps) */
1728 GM_GPSR_PART_MODE
= 1<<3, /* Bit 3: Partition mode */
1729 GM_GPSR_FC_RX_DIS
= 1<<2, /* Bit 2: Rx Flow-Control Mode Disabled */
1730 GM_GPSR_PROM_EN
= 1<<1, /* Bit 1: Promiscuous Mode Enabled */
1733 /* GM_GP_CTRL 16 bit r/w General Purpose Control Register */
1735 GM_GPCR_PROM_ENA
= 1<<14, /* Bit 14: Enable Promiscuous Mode */
1736 GM_GPCR_FC_TX_DIS
= 1<<13, /* Bit 13: Disable Tx Flow-Control Mode */
1737 GM_GPCR_TX_ENA
= 1<<12, /* Bit 12: Enable Transmit */
1738 GM_GPCR_RX_ENA
= 1<<11, /* Bit 11: Enable Receive */
1739 GM_GPCR_BURST_ENA
= 1<<10, /* Bit 10: Enable Burst Mode */
1740 GM_GPCR_LOOP_ENA
= 1<<9, /* Bit 9: Enable MAC Loopback Mode */
1741 GM_GPCR_PART_ENA
= 1<<8, /* Bit 8: Enable Partition Mode */
1742 GM_GPCR_GIGS_ENA
= 1<<7, /* Bit 7: Gigabit Speed (1000 Mbps) */
1743 GM_GPCR_FL_PASS
= 1<<6, /* Bit 6: Force Link Pass */
1744 GM_GPCR_DUP_FULL
= 1<<5, /* Bit 5: Full Duplex Mode */
1745 GM_GPCR_FC_RX_DIS
= 1<<4, /* Bit 4: Disable Rx Flow-Control Mode */
1746 GM_GPCR_SPEED_100
= 1<<3, /* Bit 3: Port Speed 100 Mbps */
1747 GM_GPCR_AU_DUP_DIS
= 1<<2, /* Bit 2: Disable Auto-Update Duplex */
1748 GM_GPCR_AU_FCT_DIS
= 1<<1, /* Bit 1: Disable Auto-Update Flow-C. */
1749 GM_GPCR_AU_SPD_DIS
= 1<<0, /* Bit 0: Disable Auto-Update Speed */
1752 #define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
1753 #define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
1755 /* GM_TX_CTRL 16 bit r/w Transmit Control Register */
1757 GM_TXCR_FORCE_JAM
= 1<<15, /* Bit 15: Force Jam / Flow-Control */
1758 GM_TXCR_CRC_DIS
= 1<<14, /* Bit 14: Disable insertion of CRC */
1759 GM_TXCR_PAD_DIS
= 1<<13, /* Bit 13: Disable padding of packets */
1760 GM_TXCR_COL_THR_MSK
= 7<<10, /* Bit 12..10: Collision Threshold */
1763 #define TX_COL_THR(x) (((x)<<10) & GM_TXCR_COL_THR_MSK)
1764 #define TX_COL_DEF 0x04 /* late collision after 64 byte */
1766 /* GM_RX_CTRL 16 bit r/w Receive Control Register */
1768 GM_RXCR_UCF_ENA
= 1<<15, /* Bit 15: Enable Unicast filtering */
1769 GM_RXCR_MCF_ENA
= 1<<14, /* Bit 14: Enable Multicast filtering */
1770 GM_RXCR_CRC_DIS
= 1<<13, /* Bit 13: Remove 4-byte CRC */
1771 GM_RXCR_PASS_FC
= 1<<12, /* Bit 12: Pass FC packets to FIFO */
1774 /* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */
1776 GM_TXPA_JAMLEN_MSK
= 0x03<<14, /* Bit 15..14: Jam Length */
1777 GM_TXPA_JAMIPG_MSK
= 0x1f<<9, /* Bit 13..9: Jam IPG */
1778 GM_TXPA_JAMDAT_MSK
= 0x1f<<4, /* Bit 8..4: IPG Jam to Data */
1780 TX_JAM_LEN_DEF
= 0x03,
1781 TX_JAM_IPG_DEF
= 0x0b,
1782 TX_IPG_JAM_DEF
= 0x1c,
1785 #define TX_JAM_LEN_VAL(x) (((x)<<14) & GM_TXPA_JAMLEN_MSK)
1786 #define TX_JAM_IPG_VAL(x) (((x)<<9) & GM_TXPA_JAMIPG_MSK)
1787 #define TX_IPG_JAM_DATA(x) (((x)<<4) & GM_TXPA_JAMDAT_MSK)
1790 /* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */
1792 GM_SMOD_DATABL_MSK
= 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */
1793 GM_SMOD_LIMIT_4
= 1<<10, /* Bit 10: 4 consecutive Tx trials */
1794 GM_SMOD_VLAN_ENA
= 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */
1795 GM_SMOD_JUMBO_ENA
= 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */
1796 GM_SMOD_IPG_MSK
= 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
1799 #define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK)
1800 #define DATA_BLIND_DEF 0x04
1802 #define IPG_DATA_VAL(x) (x & GM_SMOD_IPG_MSK)
1803 #define IPG_DATA_DEF 0x1e
1805 /* GM_SMI_CTRL 16 bit r/w SMI Control Register */
1807 GM_SMI_CT_PHY_A_MSK
= 0x1f<<11, /* Bit 15..11: PHY Device Address */
1808 GM_SMI_CT_REG_A_MSK
= 0x1f<<6, /* Bit 10.. 6: PHY Register Address */
1809 GM_SMI_CT_OP_RD
= 1<<5, /* Bit 5: OpCode Read (0=Write)*/
1810 GM_SMI_CT_RD_VAL
= 1<<4, /* Bit 4: Read Valid (Read completed) */
1811 GM_SMI_CT_BUSY
= 1<<3, /* Bit 3: Busy (Operation in progress) */
1814 #define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK)
1815 #define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK)
1817 /* GM_PHY_ADDR 16 bit r/w GPHY Address Register */
1819 GM_PAR_MIB_CLR
= 1<<5, /* Bit 5: Set MIB Clear Counter Mode */
1820 GM_PAR_MIB_TST
= 1<<4, /* Bit 4: MIB Load Counter (Test Mode) */
1823 /* Receive Frame Status Encoding */
1825 GMR_FS_LEN
= 0xffff<<16, /* Bit 31..16: Rx Frame Length */
1826 GMR_FS_LEN_SHIFT
= 16,
1827 GMR_FS_VLAN
= 1<<13, /* Bit 13: VLAN Packet */
1828 GMR_FS_JABBER
= 1<<12, /* Bit 12: Jabber Packet */
1829 GMR_FS_UN_SIZE
= 1<<11, /* Bit 11: Undersize Packet */
1830 GMR_FS_MC
= 1<<10, /* Bit 10: Multicast Packet */
1831 GMR_FS_BC
= 1<<9, /* Bit 9: Broadcast Packet */
1832 GMR_FS_RX_OK
= 1<<8, /* Bit 8: Receive OK (Good Packet) */
1833 GMR_FS_GOOD_FC
= 1<<7, /* Bit 7: Good Flow-Control Packet */
1834 GMR_FS_BAD_FC
= 1<<6, /* Bit 6: Bad Flow-Control Packet */
1835 GMR_FS_MII_ERR
= 1<<5, /* Bit 5: MII Error */
1836 GMR_FS_LONG_ERR
= 1<<4, /* Bit 4: Too Long Packet */
1837 GMR_FS_FRAGMENT
= 1<<3, /* Bit 3: Fragment */
1839 GMR_FS_CRC_ERR
= 1<<1, /* Bit 1: CRC Error */
1840 GMR_FS_RX_FF_OV
= 1<<0, /* Bit 0: Rx FIFO Overflow */
1843 * GMR_FS_ANY_ERR (analogous to XMR_FS_ANY_ERR)
1845 GMR_FS_ANY_ERR
= GMR_FS_CRC_ERR
| GMR_FS_LONG_ERR
|
1846 GMR_FS_MII_ERR
| GMR_FS_BAD_FC
| GMR_FS_GOOD_FC
|
1848 /* Rx GMAC FIFO Flush Mask (default) */
1849 RX_FF_FL_DEF_MSK
= GMR_FS_CRC_ERR
| GMR_FS_RX_FF_OV
|GMR_FS_MII_ERR
|
1850 GMR_FS_BAD_FC
| GMR_FS_GOOD_FC
| GMR_FS_UN_SIZE
|
1854 /* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */
1856 GMF_WP_TST_ON
= 1<<14, /* Write Pointer Test On */
1857 GMF_WP_TST_OFF
= 1<<13, /* Write Pointer Test Off */
1858 GMF_WP_STEP
= 1<<12, /* Write Pointer Step/Increment */
1860 GMF_RP_TST_ON
= 1<<10, /* Read Pointer Test On */
1861 GMF_RP_TST_OFF
= 1<<9, /* Read Pointer Test Off */
1862 GMF_RP_STEP
= 1<<8, /* Read Pointer Step/Increment */
1863 GMF_RX_F_FL_ON
= 1<<7, /* Rx FIFO Flush Mode On */
1864 GMF_RX_F_FL_OFF
= 1<<6, /* Rx FIFO Flush Mode Off */
1865 GMF_CLI_RX_FO
= 1<<5, /* Clear IRQ Rx FIFO Overrun */
1866 GMF_CLI_RX_FC
= 1<<4, /* Clear IRQ Rx Frame Complete */
1867 GMF_OPER_ON
= 1<<3, /* Operational Mode On */
1868 GMF_OPER_OFF
= 1<<2, /* Operational Mode Off */
1869 GMF_RST_CLR
= 1<<1, /* Clear GMAC FIFO Reset */
1870 GMF_RST_SET
= 1<<0, /* Set GMAC FIFO Reset */
1872 RX_GMF_FL_THR_DEF
= 0xa, /* flush threshold (default) */
1876 /* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */
1878 GMF_WSP_TST_ON
= 1<<18, /* Write Shadow Pointer Test On */
1879 GMF_WSP_TST_OFF
= 1<<17, /* Write Shadow Pointer Test Off */
1880 GMF_WSP_STEP
= 1<<16, /* Write Shadow Pointer Step/Increment */
1882 GMF_CLI_TX_FU
= 1<<6, /* Clear IRQ Tx FIFO Underrun */
1883 GMF_CLI_TX_FC
= 1<<5, /* Clear IRQ Tx Frame Complete */
1884 GMF_CLI_TX_PE
= 1<<4, /* Clear IRQ Tx Parity Error */
1887 /* GMAC_TI_ST_CTRL 8 bit Time Stamp Timer Ctrl Reg (YUKON only) */
1889 GMT_ST_START
= 1<<2, /* Start Time Stamp Timer */
1890 GMT_ST_STOP
= 1<<1, /* Stop Time Stamp Timer */
1891 GMT_ST_CLR_IRQ
= 1<<0, /* Clear Time Stamp Timer IRQ */
1894 /* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */
1896 GMC_H_BURST_ON
= 1<<7, /* Half Duplex Burst Mode On */
1897 GMC_H_BURST_OFF
= 1<<6, /* Half Duplex Burst Mode Off */
1898 GMC_F_LOOPB_ON
= 1<<5, /* FIFO Loopback On */
1899 GMC_F_LOOPB_OFF
= 1<<4, /* FIFO Loopback Off */
1900 GMC_PAUSE_ON
= 1<<3, /* Pause On */
1901 GMC_PAUSE_OFF
= 1<<2, /* Pause Off */
1902 GMC_RST_CLR
= 1<<1, /* Clear GMAC Reset */
1903 GMC_RST_SET
= 1<<0, /* Set GMAC Reset */
1906 /* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */
1908 GPC_SEL_BDT
= 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */
1909 GPC_INT_POL_HI
= 1<<27, /* IRQ Polarity is Active HIGH */
1910 GPC_75_OHM
= 1<<26, /* Use 75 Ohm Termination instead of 50 */
1911 GPC_DIS_FC
= 1<<25, /* Disable Automatic Fiber/Copper Detection */
1912 GPC_DIS_SLEEP
= 1<<24, /* Disable Energy Detect */
1913 GPC_HWCFG_M_3
= 1<<23, /* HWCFG_MODE[3] */
1914 GPC_HWCFG_M_2
= 1<<22, /* HWCFG_MODE[2] */
1915 GPC_HWCFG_M_1
= 1<<21, /* HWCFG_MODE[1] */
1916 GPC_HWCFG_M_0
= 1<<20, /* HWCFG_MODE[0] */
1917 GPC_ANEG_0
= 1<<19, /* ANEG[0] */
1918 GPC_ENA_XC
= 1<<18, /* Enable MDI crossover */
1919 GPC_DIS_125
= 1<<17, /* Disable 125 MHz clock */
1920 GPC_ANEG_3
= 1<<16, /* ANEG[3] */
1921 GPC_ANEG_2
= 1<<15, /* ANEG[2] */
1922 GPC_ANEG_1
= 1<<14, /* ANEG[1] */
1923 GPC_ENA_PAUSE
= 1<<13, /* Enable Pause (SYM_OR_REM) */
1924 GPC_PHYADDR_4
= 1<<12, /* Bit 4 of Phy Addr */
1925 GPC_PHYADDR_3
= 1<<11, /* Bit 3 of Phy Addr */
1926 GPC_PHYADDR_2
= 1<<10, /* Bit 2 of Phy Addr */
1927 GPC_PHYADDR_1
= 1<<9, /* Bit 1 of Phy Addr */
1928 GPC_PHYADDR_0
= 1<<8, /* Bit 0 of Phy Addr */
1929 /* Bits 7..2: reserved */
1930 GPC_RST_CLR
= 1<<1, /* Clear GPHY Reset */
1931 GPC_RST_SET
= 1<<0, /* Set GPHY Reset */
1934 #define GPC_HWCFG_GMII_COP (GPC_HWCFG_M_3|GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0)
1935 #define GPC_HWCFG_GMII_FIB (GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0)
1936 #define GPC_ANEG_ADV_ALL_M (GPC_ANEG_3 | GPC_ANEG_2 | GPC_ANEG_1 | GPC_ANEG_0)
1938 /* forced speed and duplex mode (don't mix with other ANEG bits) */
1939 #define GPC_FRC10MBIT_HALF 0
1940 #define GPC_FRC10MBIT_FULL GPC_ANEG_0
1941 #define GPC_FRC100MBIT_HALF GPC_ANEG_1
1942 #define GPC_FRC100MBIT_FULL (GPC_ANEG_0 | GPC_ANEG_1)
1944 /* auto-negotiation with limited advertised speeds */
1945 /* mix only with master/slave settings (for copper) */
1946 #define GPC_ADV_1000_HALF GPC_ANEG_2
1947 #define GPC_ADV_1000_FULL GPC_ANEG_3
1948 #define GPC_ADV_ALL (GPC_ANEG_2 | GPC_ANEG_3)
1950 /* master/slave settings */
1951 /* only for copper with 1000 Mbps */
1952 #define GPC_FORCE_MASTER 0
1953 #define GPC_FORCE_SLAVE GPC_ANEG_0
1954 #define GPC_PREF_MASTER GPC_ANEG_1
1955 #define GPC_PREF_SLAVE (GPC_ANEG_1 | GPC_ANEG_0)
1957 /* GMAC_IRQ_SRC 8 bit GMAC Interrupt Source Reg (YUKON only) */
1958 /* GMAC_IRQ_MSK 8 bit GMAC Interrupt Mask Reg (YUKON only) */
1960 GM_IS_TX_CO_OV
= 1<<5, /* Transmit Counter Overflow IRQ */
1961 GM_IS_RX_CO_OV
= 1<<4, /* Receive Counter Overflow IRQ */
1962 GM_IS_TX_FF_UR
= 1<<3, /* Transmit FIFO Underrun */
1963 GM_IS_TX_COMPL
= 1<<2, /* Frame Transmission Complete */
1964 GM_IS_RX_FF_OR
= 1<<1, /* Receive FIFO Overrun */
1965 GM_IS_RX_COMPL
= 1<<0, /* Frame Reception Complete */
1967 #define GMAC_DEF_MSK (GM_IS_RX_FF_OR | GM_IS_TX_FF_UR)
1969 /* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
1970 /* Bits 15.. 2: reserved */
1971 GMLC_RST_CLR
= 1<<1, /* Clear GMAC Link Reset */
1972 GMLC_RST_SET
= 1<<0, /* Set GMAC Link Reset */
1975 /* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */
1976 WOL_CTL_LINK_CHG_OCC
= 1<<15,
1977 WOL_CTL_MAGIC_PKT_OCC
= 1<<14,
1978 WOL_CTL_PATTERN_OCC
= 1<<13,
1979 WOL_CTL_CLEAR_RESULT
= 1<<12,
1980 WOL_CTL_ENA_PME_ON_LINK_CHG
= 1<<11,
1981 WOL_CTL_DIS_PME_ON_LINK_CHG
= 1<<10,
1982 WOL_CTL_ENA_PME_ON_MAGIC_PKT
= 1<<9,
1983 WOL_CTL_DIS_PME_ON_MAGIC_PKT
= 1<<8,
1984 WOL_CTL_ENA_PME_ON_PATTERN
= 1<<7,
1985 WOL_CTL_DIS_PME_ON_PATTERN
= 1<<6,
1986 WOL_CTL_ENA_LINK_CHG_UNIT
= 1<<5,
1987 WOL_CTL_DIS_LINK_CHG_UNIT
= 1<<4,
1988 WOL_CTL_ENA_MAGIC_PKT_UNIT
= 1<<3,
1989 WOL_CTL_DIS_MAGIC_PKT_UNIT
= 1<<2,
1990 WOL_CTL_ENA_PATTERN_UNIT
= 1<<1,
1991 WOL_CTL_DIS_PATTERN_UNIT
= 1<<0,
1994 #define WOL_CTL_DEFAULT \
1995 (WOL_CTL_DIS_PME_ON_LINK_CHG | \
1996 WOL_CTL_DIS_PME_ON_PATTERN | \
1997 WOL_CTL_DIS_PME_ON_MAGIC_PKT | \
1998 WOL_CTL_DIS_LINK_CHG_UNIT | \
1999 WOL_CTL_DIS_PATTERN_UNIT | \
2000 WOL_CTL_DIS_MAGIC_PKT_UNIT)
2002 /* WOL_MATCH_CTL 8 bit WOL Match Control Reg */
2003 #define WOL_CTL_PATT_ENA(x) (1 << (x))
2006 /* XMAC II registers */
2008 XM_MMU_CMD
= 0x0000, /* 16 bit r/w MMU Command Register */
2009 XM_POFF
= 0x0008, /* 32 bit r/w Packet Offset Register */
2010 XM_BURST
= 0x000c, /* 32 bit r/w Burst Register for half duplex*/
2011 XM_1L_VLAN_TAG
= 0x0010, /* 16 bit r/w One Level VLAN Tag ID */
2012 XM_2L_VLAN_TAG
= 0x0014, /* 16 bit r/w Two Level VLAN Tag ID */
2013 XM_TX_CMD
= 0x0020, /* 16 bit r/w Transmit Command Register */
2014 XM_TX_RT_LIM
= 0x0024, /* 16 bit r/w Transmit Retry Limit Register */
2015 XM_TX_STIME
= 0x0028, /* 16 bit r/w Transmit Slottime Register */
2016 XM_TX_IPG
= 0x002c, /* 16 bit r/w Transmit Inter Packet Gap */
2017 XM_RX_CMD
= 0x0030, /* 16 bit r/w Receive Command Register */
2018 XM_PHY_ADDR
= 0x0034, /* 16 bit r/w PHY Address Register */
2019 XM_PHY_DATA
= 0x0038, /* 16 bit r/w PHY Data Register */
2020 XM_GP_PORT
= 0x0040, /* 32 bit r/w General Purpose Port Register */
2021 XM_IMSK
= 0x0044, /* 16 bit r/w Interrupt Mask Register */
2022 XM_ISRC
= 0x0048, /* 16 bit r/o Interrupt Status Register */
2023 XM_HW_CFG
= 0x004c, /* 16 bit r/w Hardware Config Register */
2024 XM_TX_LO_WM
= 0x0060, /* 16 bit r/w Tx FIFO Low Water Mark */
2025 XM_TX_HI_WM
= 0x0062, /* 16 bit r/w Tx FIFO High Water Mark */
2026 XM_TX_THR
= 0x0064, /* 16 bit r/w Tx Request Threshold */
2027 XM_HT_THR
= 0x0066, /* 16 bit r/w Host Request Threshold */
2028 XM_PAUSE_DA
= 0x0068, /* NA reg r/w Pause Destination Address */
2029 XM_CTL_PARA
= 0x0070, /* 32 bit r/w Control Parameter Register */
2030 XM_MAC_OPCODE
= 0x0074, /* 16 bit r/w Opcode for MAC control frames */
2031 XM_MAC_PTIME
= 0x0076, /* 16 bit r/w Pause time for MAC ctrl frames*/
2032 XM_TX_STAT
= 0x0078, /* 32 bit r/o Tx Status LIFO Register */
2034 XM_EXM_START
= 0x0080, /* r/w Start Address of the EXM Regs */
2035 #define XM_EXM(reg) (XM_EXM_START + ((reg) << 3))
2039 XM_SRC_CHK
= 0x0100, /* NA reg r/w Source Check Address Register */
2040 XM_SA
= 0x0108, /* NA reg r/w Station Address Register */
2041 XM_HSM
= 0x0110, /* 64 bit r/w Hash Match Address Registers */
2042 XM_RX_LO_WM
= 0x0118, /* 16 bit r/w Receive Low Water Mark */
2043 XM_RX_HI_WM
= 0x011a, /* 16 bit r/w Receive High Water Mark */
2044 XM_RX_THR
= 0x011c, /* 32 bit r/w Receive Request Threshold */
2045 XM_DEV_ID
= 0x0120, /* 32 bit r/o Device ID Register */
2046 XM_MODE
= 0x0124, /* 32 bit r/w Mode Register */
2047 XM_LSA
= 0x0128, /* NA reg r/o Last Source Register */
2048 XM_TS_READ
= 0x0130, /* 32 bit r/o Time Stamp Read Register */
2049 XM_TS_LOAD
= 0x0134, /* 32 bit r/o Time Stamp Load Value */
2050 XM_STAT_CMD
= 0x0200, /* 16 bit r/w Statistics Command Register */
2051 XM_RX_CNT_EV
= 0x0204, /* 32 bit r/o Rx Counter Event Register */
2052 XM_TX_CNT_EV
= 0x0208, /* 32 bit r/o Tx Counter Event Register */
2053 XM_RX_EV_MSK
= 0x020c, /* 32 bit r/w Rx Counter Event Mask */
2054 XM_TX_EV_MSK
= 0x0210, /* 32 bit r/w Tx Counter Event Mask */
2055 XM_TXF_OK
= 0x0280, /* 32 bit r/o Frames Transmitted OK Conuter */
2056 XM_TXO_OK_HI
= 0x0284, /* 32 bit r/o Octets Transmitted OK High Cnt*/
2057 XM_TXO_OK_LO
= 0x0288, /* 32 bit r/o Octets Transmitted OK Low Cnt */
2058 XM_TXF_BC_OK
= 0x028c, /* 32 bit r/o Broadcast Frames Xmitted OK */
2059 XM_TXF_MC_OK
= 0x0290, /* 32 bit r/o Multicast Frames Xmitted OK */
2060 XM_TXF_UC_OK
= 0x0294, /* 32 bit r/o Unicast Frames Xmitted OK */
2061 XM_TXF_LONG
= 0x0298, /* 32 bit r/o Tx Long Frame Counter */
2062 XM_TXE_BURST
= 0x029c, /* 32 bit r/o Tx Burst Event Counter */
2063 XM_TXF_MPAUSE
= 0x02a0, /* 32 bit r/o Tx Pause MAC Ctrl Frame Cnt */
2064 XM_TXF_MCTRL
= 0x02a4, /* 32 bit r/o Tx MAC Ctrl Frame Counter */
2065 XM_TXF_SNG_COL
= 0x02a8, /* 32 bit r/o Tx Single Collision Counter */
2066 XM_TXF_MUL_COL
= 0x02ac, /* 32 bit r/o Tx Multiple Collision Counter */
2067 XM_TXF_ABO_COL
= 0x02b0, /* 32 bit r/o Tx aborted due to Exces. Col. */
2068 XM_TXF_LAT_COL
= 0x02b4, /* 32 bit r/o Tx Late Collision Counter */
2069 XM_TXF_DEF
= 0x02b8, /* 32 bit r/o Tx Deferred Frame Counter */
2070 XM_TXF_EX_DEF
= 0x02bc, /* 32 bit r/o Tx Excessive Deferall Counter */
2071 XM_TXE_FIFO_UR
= 0x02c0, /* 32 bit r/o Tx FIFO Underrun Event Cnt */
2072 XM_TXE_CS_ERR
= 0x02c4, /* 32 bit r/o Tx Carrier Sense Error Cnt */
2073 XM_TXP_UTIL
= 0x02c8, /* 32 bit r/o Tx Utilization in % */
2074 XM_TXF_64B
= 0x02d0, /* 32 bit r/o 64 Byte Tx Frame Counter */
2075 XM_TXF_127B
= 0x02d4, /* 32 bit r/o 65-127 Byte Tx Frame Counter */
2076 XM_TXF_255B
= 0x02d8, /* 32 bit r/o 128-255 Byte Tx Frame Counter */
2077 XM_TXF_511B
= 0x02dc, /* 32 bit r/o 256-511 Byte Tx Frame Counter */
2078 XM_TXF_1023B
= 0x02e0, /* 32 bit r/o 512-1023 Byte Tx Frame Counter*/
2079 XM_TXF_MAX_SZ
= 0x02e4, /* 32 bit r/o 1024-MaxSize Byte Tx Frame Cnt*/
2080 XM_RXF_OK
= 0x0300, /* 32 bit r/o Frames Received OK */
2081 XM_RXO_OK_HI
= 0x0304, /* 32 bit r/o Octets Received OK High Cnt */
2082 XM_RXO_OK_LO
= 0x0308, /* 32 bit r/o Octets Received OK Low Counter*/
2083 XM_RXF_BC_OK
= 0x030c, /* 32 bit r/o Broadcast Frames Received OK */
2084 XM_RXF_MC_OK
= 0x0310, /* 32 bit r/o Multicast Frames Received OK */
2085 XM_RXF_UC_OK
= 0x0314, /* 32 bit r/o Unicast Frames Received OK */
2086 XM_RXF_MPAUSE
= 0x0318, /* 32 bit r/o Rx Pause MAC Ctrl Frame Cnt */
2087 XM_RXF_MCTRL
= 0x031c, /* 32 bit r/o Rx MAC Ctrl Frame Counter */
2088 XM_RXF_INV_MP
= 0x0320, /* 32 bit r/o Rx invalid Pause Frame Cnt */
2089 XM_RXF_INV_MOC
= 0x0324, /* 32 bit r/o Rx Frames with inv. MAC Opcode*/
2090 XM_RXE_BURST
= 0x0328, /* 32 bit r/o Rx Burst Event Counter */
2091 XM_RXE_FMISS
= 0x032c, /* 32 bit r/o Rx Missed Frames Event Cnt */
2092 XM_RXF_FRA_ERR
= 0x0330, /* 32 bit r/o Rx Framing Error Counter */
2093 XM_RXE_FIFO_OV
= 0x0334, /* 32 bit r/o Rx FIFO overflow Event Cnt */
2094 XM_RXF_JAB_PKT
= 0x0338, /* 32 bit r/o Rx Jabber Packet Frame Cnt */
2095 XM_RXE_CAR_ERR
= 0x033c, /* 32 bit r/o Rx Carrier Event Error Cnt */
2096 XM_RXF_LEN_ERR
= 0x0340, /* 32 bit r/o Rx in Range Length Error */
2097 XM_RXE_SYM_ERR
= 0x0344, /* 32 bit r/o Rx Symbol Error Counter */
2098 XM_RXE_SHT_ERR
= 0x0348, /* 32 bit r/o Rx Short Event Error Cnt */
2099 XM_RXE_RUNT
= 0x034c, /* 32 bit r/o Rx Runt Event Counter */
2100 XM_RXF_LNG_ERR
= 0x0350, /* 32 bit r/o Rx Frame too Long Error Cnt */
2101 XM_RXF_FCS_ERR
= 0x0354, /* 32 bit r/o Rx Frame Check Seq. Error Cnt */
2102 XM_RXF_CEX_ERR
= 0x035c, /* 32 bit r/o Rx Carrier Ext Error Frame Cnt*/
2103 XM_RXP_UTIL
= 0x0360, /* 32 bit r/o Rx Utilization in % */
2104 XM_RXF_64B
= 0x0368, /* 32 bit r/o 64 Byte Rx Frame Counter */
2105 XM_RXF_127B
= 0x036c, /* 32 bit r/o 65-127 Byte Rx Frame Counter */
2106 XM_RXF_255B
= 0x0370, /* 32 bit r/o 128-255 Byte Rx Frame Counter */
2107 XM_RXF_511B
= 0x0374, /* 32 bit r/o 256-511 Byte Rx Frame Counter */
2108 XM_RXF_1023B
= 0x0378, /* 32 bit r/o 512-1023 Byte Rx Frame Counter*/
2109 XM_RXF_MAX_SZ
= 0x037c, /* 32 bit r/o 1024-MaxSize Byte Rx Frame Cnt*/
2112 /* XM_MMU_CMD 16 bit r/w MMU Command Register */
2114 XM_MMU_PHY_RDY
= 1<<12, /* Bit 12: PHY Read Ready */
2115 XM_MMU_PHY_BUSY
= 1<<11, /* Bit 11: PHY Busy */
2116 XM_MMU_IGN_PF
= 1<<10, /* Bit 10: Ignore Pause Frame */
2117 XM_MMU_MAC_LB
= 1<<9, /* Bit 9: Enable MAC Loopback */
2118 XM_MMU_FRC_COL
= 1<<7, /* Bit 7: Force Collision */
2119 XM_MMU_SIM_COL
= 1<<6, /* Bit 6: Simulate Collision */
2120 XM_MMU_NO_PRE
= 1<<5, /* Bit 5: No MDIO Preamble */
2121 XM_MMU_GMII_FD
= 1<<4, /* Bit 4: GMII uses Full Duplex */
2122 XM_MMU_RAT_CTRL
= 1<<3, /* Bit 3: Enable Rate Control */
2123 XM_MMU_GMII_LOOP
= 1<<2, /* Bit 2: PHY is in Loopback Mode */
2124 XM_MMU_ENA_RX
= 1<<1, /* Bit 1: Enable Receiver */
2125 XM_MMU_ENA_TX
= 1<<0, /* Bit 0: Enable Transmitter */
2129 /* XM_TX_CMD 16 bit r/w Transmit Command Register */
2131 XM_TX_BK2BK
= 1<<6, /* Bit 6: Ignor Carrier Sense (Tx Bk2Bk)*/
2132 XM_TX_ENC_BYP
= 1<<5, /* Bit 5: Set Encoder in Bypass Mode */
2133 XM_TX_SAM_LINE
= 1<<4, /* Bit 4: (sc) Start utilization calculation */
2134 XM_TX_NO_GIG_MD
= 1<<3, /* Bit 3: Disable Carrier Extension */
2135 XM_TX_NO_PRE
= 1<<2, /* Bit 2: Disable Preamble Generation */
2136 XM_TX_NO_CRC
= 1<<1, /* Bit 1: Disable CRC Generation */
2137 XM_TX_AUTO_PAD
= 1<<0, /* Bit 0: Enable Automatic Padding */
2140 /* XM_TX_RT_LIM 16 bit r/w Transmit Retry Limit Register */
2141 #define XM_RT_LIM_MSK 0x1f /* Bit 4..0: Tx Retry Limit */
2144 /* XM_TX_STIME 16 bit r/w Transmit Slottime Register */
2145 #define XM_STIME_MSK 0x7f /* Bit 6..0: Tx Slottime bits */
2148 /* XM_TX_IPG 16 bit r/w Transmit Inter Packet Gap */
2149 #define XM_IPG_MSK 0xff /* Bit 7..0: IPG value bits */
2152 /* XM_RX_CMD 16 bit r/w Receive Command Register */
2154 XM_RX_LENERR_OK
= 1<<8, /* Bit 8 don't set Rx Err bit for */
2155 /* inrange error packets */
2156 XM_RX_BIG_PK_OK
= 1<<7, /* Bit 7 don't set Rx Err bit for */
2158 XM_RX_IPG_CAP
= 1<<6, /* Bit 6 repl. type field with IPG */
2159 XM_RX_TP_MD
= 1<<5, /* Bit 5: Enable transparent Mode */
2160 XM_RX_STRIP_FCS
= 1<<4, /* Bit 4: Enable FCS Stripping */
2161 XM_RX_SELF_RX
= 1<<3, /* Bit 3: Enable Rx of own packets */
2162 XM_RX_SAM_LINE
= 1<<2, /* Bit 2: (sc) Start utilization calculation */
2163 XM_RX_STRIP_PAD
= 1<<1, /* Bit 1: Strip pad bytes of Rx frames */
2164 XM_RX_DIS_CEXT
= 1<<0, /* Bit 0: Disable carrier ext. check */
2168 /* XM_GP_PORT 32 bit r/w General Purpose Port Register */
2170 XM_GP_ANIP
= 1<<6, /* Bit 6: (ro) Auto-Neg. in progress */
2171 XM_GP_FRC_INT
= 1<<5, /* Bit 5: (sc) Force Interrupt */
2172 XM_GP_RES_MAC
= 1<<3, /* Bit 3: (sc) Reset MAC and FIFOs */
2173 XM_GP_RES_STAT
= 1<<2, /* Bit 2: (sc) Reset the statistics module */
2174 XM_GP_INP_ASS
= 1<<0, /* Bit 0: (ro) GP Input Pin asserted */
2178 /* XM_IMSK 16 bit r/w Interrupt Mask Register */
2179 /* XM_ISRC 16 bit r/o Interrupt Status Register */
2181 XM_IS_LNK_AE
= 1<<14, /* Bit 14: Link Asynchronous Event */
2182 XM_IS_TX_ABORT
= 1<<13, /* Bit 13: Transmit Abort, late Col. etc */
2183 XM_IS_FRC_INT
= 1<<12, /* Bit 12: Force INT bit set in GP */
2184 XM_IS_INP_ASS
= 1<<11, /* Bit 11: Input Asserted, GP bit 0 set */
2185 XM_IS_LIPA_RC
= 1<<10, /* Bit 10: Link Partner requests config */
2186 XM_IS_RX_PAGE
= 1<<9, /* Bit 9: Page Received */
2187 XM_IS_TX_PAGE
= 1<<8, /* Bit 8: Next Page Loaded for Transmit */
2188 XM_IS_AND
= 1<<7, /* Bit 7: Auto-Negotiation Done */
2189 XM_IS_TSC_OV
= 1<<6, /* Bit 6: Time Stamp Counter Overflow */
2190 XM_IS_RXC_OV
= 1<<5, /* Bit 5: Rx Counter Event Overflow */
2191 XM_IS_TXC_OV
= 1<<4, /* Bit 4: Tx Counter Event Overflow */
2192 XM_IS_RXF_OV
= 1<<3, /* Bit 3: Receive FIFO Overflow */
2193 XM_IS_TXF_UR
= 1<<2, /* Bit 2: Transmit FIFO Underrun */
2194 XM_IS_TX_COMP
= 1<<1, /* Bit 1: Frame Tx Complete */
2195 XM_IS_RX_COMP
= 1<<0, /* Bit 0: Frame Rx Complete */
2198 #define XM_DEF_MSK (~(XM_IS_INP_ASS | XM_IS_LIPA_RC | \
2199 XM_IS_RXF_OV | XM_IS_TXF_UR))
2202 /* XM_HW_CFG 16 bit r/w Hardware Config Register */
2204 XM_HW_GEN_EOP
= 1<<3, /* Bit 3: generate End of Packet pulse */
2205 XM_HW_COM4SIG
= 1<<2, /* Bit 2: use Comma Detect for Sig. Det.*/
2206 XM_HW_GMII_MD
= 1<<0, /* Bit 0: GMII Interface selected */
2210 /* XM_TX_LO_WM 16 bit r/w Tx FIFO Low Water Mark */
2211 /* XM_TX_HI_WM 16 bit r/w Tx FIFO High Water Mark */
2212 #define XM_TX_WM_MSK 0x01ff /* Bit 9.. 0 Tx FIFO Watermark bits */
2214 /* XM_TX_THR 16 bit r/w Tx Request Threshold */
2215 /* XM_HT_THR 16 bit r/w Host Request Threshold */
2216 /* XM_RX_THR 16 bit r/w Rx Request Threshold */
2217 #define XM_THR_MSK 0x03ff /* Bit 10.. 0 Rx/Tx Request Threshold bits */
2220 /* XM_TX_STAT 32 bit r/o Tx Status LIFO Register */
2222 XM_ST_VALID
= (1UL<<31), /* Bit 31: Status Valid */
2223 XM_ST_BYTE_CNT
= (0x3fffL
<<17), /* Bit 30..17: Tx frame Length */
2224 XM_ST_RETRY_CNT
= (0x1fL
<<12), /* Bit 16..12: Retry Count */
2225 XM_ST_EX_COL
= 1<<11, /* Bit 11: Excessive Collisions */
2226 XM_ST_EX_DEF
= 1<<10, /* Bit 10: Excessive Deferral */
2227 XM_ST_BURST
= 1<<9, /* Bit 9: p. xmitted in burst md*/
2228 XM_ST_DEFER
= 1<<8, /* Bit 8: packet was defered */
2229 XM_ST_BC
= 1<<7, /* Bit 7: Broadcast packet */
2230 XM_ST_MC
= 1<<6, /* Bit 6: Multicast packet */
2231 XM_ST_UC
= 1<<5, /* Bit 5: Unicast packet */
2232 XM_ST_TX_UR
= 1<<4, /* Bit 4: FIFO Underrun occured */
2233 XM_ST_CS_ERR
= 1<<3, /* Bit 3: Carrier Sense Error */
2234 XM_ST_LAT_COL
= 1<<2, /* Bit 2: Late Collision Error */
2235 XM_ST_MUL_COL
= 1<<1, /* Bit 1: Multiple Collisions */
2236 XM_ST_SGN_COL
= 1<<0, /* Bit 0: Single Collision */
2239 /* XM_RX_LO_WM 16 bit r/w Receive Low Water Mark */
2240 /* XM_RX_HI_WM 16 bit r/w Receive High Water Mark */
2241 #define XM_RX_WM_MSK 0x03ff /* Bit 11.. 0: Rx FIFO Watermark bits */
2244 /* XM_DEV_ID 32 bit r/o Device ID Register */
2245 #define XM_DEV_OUI (0x00ffffffUL<<8) /* Bit 31..8: Device OUI */
2246 #define XM_DEV_REV (0x07L << 5) /* Bit 7..5: Chip Rev Num */
2249 /* XM_MODE 32 bit r/w Mode Register */
2251 XM_MD_ENA_REJ
= 1<<26, /* Bit 26: Enable Frame Reject */
2252 XM_MD_SPOE_E
= 1<<25, /* Bit 25: Send Pause on Edge */
2253 /* extern generated */
2254 XM_MD_TX_REP
= 1<<24, /* Bit 24: Transmit Repeater Mode */
2255 XM_MD_SPOFF_I
= 1<<23, /* Bit 23: Send Pause on FIFO full */
2256 /* intern generated */
2257 XM_MD_LE_STW
= 1<<22, /* Bit 22: Rx Stat Word in Little Endian */
2258 XM_MD_TX_CONT
= 1<<21, /* Bit 21: Send Continuous */
2259 XM_MD_TX_PAUSE
= 1<<20, /* Bit 20: (sc) Send Pause Frame */
2260 XM_MD_ATS
= 1<<19, /* Bit 19: Append Time Stamp */
2261 XM_MD_SPOL_I
= 1<<18, /* Bit 18: Send Pause on Low */
2262 /* intern generated */
2263 XM_MD_SPOH_I
= 1<<17, /* Bit 17: Send Pause on High */
2264 /* intern generated */
2265 XM_MD_CAP
= 1<<16, /* Bit 16: Check Address Pair */
2266 XM_MD_ENA_HASH
= 1<<15, /* Bit 15: Enable Hashing */
2267 XM_MD_CSA
= 1<<14, /* Bit 14: Check Station Address */
2268 XM_MD_CAA
= 1<<13, /* Bit 13: Check Address Array */
2269 XM_MD_RX_MCTRL
= 1<<12, /* Bit 12: Rx MAC Control Frame */
2270 XM_MD_RX_RUNT
= 1<<11, /* Bit 11: Rx Runt Frames */
2271 XM_MD_RX_IRLE
= 1<<10, /* Bit 10: Rx in Range Len Err Frame */
2272 XM_MD_RX_LONG
= 1<<9, /* Bit 9: Rx Long Frame */
2273 XM_MD_RX_CRCE
= 1<<8, /* Bit 8: Rx CRC Error Frame */
2274 XM_MD_RX_ERR
= 1<<7, /* Bit 7: Rx Error Frame */
2275 XM_MD_DIS_UC
= 1<<6, /* Bit 6: Disable Rx Unicast */
2276 XM_MD_DIS_MC
= 1<<5, /* Bit 5: Disable Rx Multicast */
2277 XM_MD_DIS_BC
= 1<<4, /* Bit 4: Disable Rx Broadcast */
2278 XM_MD_ENA_PROM
= 1<<3, /* Bit 3: Enable Promiscuous */
2279 XM_MD_ENA_BE
= 1<<2, /* Bit 2: Enable Big Endian */
2280 XM_MD_FTF
= 1<<1, /* Bit 1: (sc) Flush Tx FIFO */
2281 XM_MD_FRF
= 1<<0, /* Bit 0: (sc) Flush Rx FIFO */
2284 #define XM_PAUSE_MODE (XM_MD_SPOE_E | XM_MD_SPOL_I | XM_MD_SPOH_I)
2285 #define XM_DEF_MODE (XM_MD_RX_RUNT | XM_MD_RX_IRLE | XM_MD_RX_LONG |\
2286 XM_MD_RX_CRCE | XM_MD_RX_ERR | XM_MD_CSA)
2288 /* XM_STAT_CMD 16 bit r/w Statistics Command Register */
2290 XM_SC_SNP_RXC
= 1<<5, /* Bit 5: (sc) Snap Rx Counters */
2291 XM_SC_SNP_TXC
= 1<<4, /* Bit 4: (sc) Snap Tx Counters */
2292 XM_SC_CP_RXC
= 1<<3, /* Bit 3: Copy Rx Counters Continuously */
2293 XM_SC_CP_TXC
= 1<<2, /* Bit 2: Copy Tx Counters Continuously */
2294 XM_SC_CLR_RXC
= 1<<1, /* Bit 1: (sc) Clear Rx Counters */
2295 XM_SC_CLR_TXC
= 1<<0, /* Bit 0: (sc) Clear Tx Counters */
2299 /* XM_RX_CNT_EV 32 bit r/o Rx Counter Event Register */
2300 /* XM_RX_EV_MSK 32 bit r/w Rx Counter Event Mask */
2302 XMR_MAX_SZ_OV
= 1<<31, /* Bit 31: 1024-MaxSize Rx Cnt Ov*/
2303 XMR_1023B_OV
= 1<<30, /* Bit 30: 512-1023Byte Rx Cnt Ov*/
2304 XMR_511B_OV
= 1<<29, /* Bit 29: 256-511 Byte Rx Cnt Ov*/
2305 XMR_255B_OV
= 1<<28, /* Bit 28: 128-255 Byte Rx Cnt Ov*/
2306 XMR_127B_OV
= 1<<27, /* Bit 27: 65-127 Byte Rx Cnt Ov */
2307 XMR_64B_OV
= 1<<26, /* Bit 26: 64 Byte Rx Cnt Ov */
2308 XMR_UTIL_OV
= 1<<25, /* Bit 25: Rx Util Cnt Overflow */
2309 XMR_UTIL_UR
= 1<<24, /* Bit 24: Rx Util Cnt Underrun */
2310 XMR_CEX_ERR_OV
= 1<<23, /* Bit 23: CEXT Err Cnt Ov */
2311 XMR_FCS_ERR_OV
= 1<<21, /* Bit 21: Rx FCS Error Cnt Ov */
2312 XMR_LNG_ERR_OV
= 1<<20, /* Bit 20: Rx too Long Err Cnt Ov*/
2313 XMR_RUNT_OV
= 1<<19, /* Bit 19: Runt Event Cnt Ov */
2314 XMR_SHT_ERR_OV
= 1<<18, /* Bit 18: Rx Short Ev Err Cnt Ov*/
2315 XMR_SYM_ERR_OV
= 1<<17, /* Bit 17: Rx Sym Err Cnt Ov */
2316 XMR_CAR_ERR_OV
= 1<<15, /* Bit 15: Rx Carr Ev Err Cnt Ov */
2317 XMR_JAB_PKT_OV
= 1<<14, /* Bit 14: Rx Jabb Packet Cnt Ov */
2318 XMR_FIFO_OV
= 1<<13, /* Bit 13: Rx FIFO Ov Ev Cnt Ov */
2319 XMR_FRA_ERR_OV
= 1<<12, /* Bit 12: Rx Framing Err Cnt Ov */
2320 XMR_FMISS_OV
= 1<<11, /* Bit 11: Rx Missed Ev Cnt Ov */
2321 XMR_BURST
= 1<<10, /* Bit 10: Rx Burst Event Cnt Ov */
2322 XMR_INV_MOC
= 1<<9, /* Bit 9: Rx with inv. MAC OC Ov*/
2323 XMR_INV_MP
= 1<<8, /* Bit 8: Rx inv Pause Frame Ov */
2324 XMR_MCTRL_OV
= 1<<7, /* Bit 7: Rx MAC Ctrl-F Cnt Ov */
2325 XMR_MPAUSE_OV
= 1<<6, /* Bit 6: Rx Pause MAC Ctrl-F Ov*/
2326 XMR_UC_OK_OV
= 1<<5, /* Bit 5: Rx Unicast Frame CntOv*/
2327 XMR_MC_OK_OV
= 1<<4, /* Bit 4: Rx Multicast Cnt Ov */
2328 XMR_BC_OK_OV
= 1<<3, /* Bit 3: Rx Broadcast Cnt Ov */
2329 XMR_OK_LO_OV
= 1<<2, /* Bit 2: Octets Rx OK Low CntOv*/
2330 XMR_OK_HI_OV
= 1<<1, /* Bit 1: Octets Rx OK Hi Cnt Ov*/
2331 XMR_OK_OV
= 1<<0, /* Bit 0: Frames Received Ok Ov */
2334 #define XMR_DEF_MSK (XMR_OK_LO_OV | XMR_OK_HI_OV)
2336 /* XM_TX_CNT_EV 32 bit r/o Tx Counter Event Register */
2337 /* XM_TX_EV_MSK 32 bit r/w Tx Counter Event Mask */
2339 XMT_MAX_SZ_OV
= 1<<25, /* Bit 25: 1024-MaxSize Tx Cnt Ov*/
2340 XMT_1023B_OV
= 1<<24, /* Bit 24: 512-1023Byte Tx Cnt Ov*/
2341 XMT_511B_OV
= 1<<23, /* Bit 23: 256-511 Byte Tx Cnt Ov*/
2342 XMT_255B_OV
= 1<<22, /* Bit 22: 128-255 Byte Tx Cnt Ov*/
2343 XMT_127B_OV
= 1<<21, /* Bit 21: 65-127 Byte Tx Cnt Ov */
2344 XMT_64B_OV
= 1<<20, /* Bit 20: 64 Byte Tx Cnt Ov */
2345 XMT_UTIL_OV
= 1<<19, /* Bit 19: Tx Util Cnt Overflow */
2346 XMT_UTIL_UR
= 1<<18, /* Bit 18: Tx Util Cnt Underrun */
2347 XMT_CS_ERR_OV
= 1<<17, /* Bit 17: Tx Carr Sen Err Cnt Ov*/
2348 XMT_FIFO_UR_OV
= 1<<16, /* Bit 16: Tx FIFO Ur Ev Cnt Ov */
2349 XMT_EX_DEF_OV
= 1<<15, /* Bit 15: Tx Ex Deferall Cnt Ov */
2350 XMT_DEF
= 1<<14, /* Bit 14: Tx Deferred Cnt Ov */
2351 XMT_LAT_COL_OV
= 1<<13, /* Bit 13: Tx Late Col Cnt Ov */
2352 XMT_ABO_COL_OV
= 1<<12, /* Bit 12: Tx abo dueto Ex Col Ov*/
2353 XMT_MUL_COL_OV
= 1<<11, /* Bit 11: Tx Mult Col Cnt Ov */
2354 XMT_SNG_COL
= 1<<10, /* Bit 10: Tx Single Col Cnt Ov */
2355 XMT_MCTRL_OV
= 1<<9, /* Bit 9: Tx MAC Ctrl Counter Ov*/
2356 XMT_MPAUSE
= 1<<8, /* Bit 8: Tx Pause MAC Ctrl-F Ov*/
2357 XMT_BURST
= 1<<7, /* Bit 7: Tx Burst Event Cnt Ov */
2358 XMT_LONG
= 1<<6, /* Bit 6: Tx Long Frame Cnt Ov */
2359 XMT_UC_OK_OV
= 1<<5, /* Bit 5: Tx Unicast Cnt Ov */
2360 XMT_MC_OK_OV
= 1<<4, /* Bit 4: Tx Multicast Cnt Ov */
2361 XMT_BC_OK_OV
= 1<<3, /* Bit 3: Tx Broadcast Cnt Ov */
2362 XMT_OK_LO_OV
= 1<<2, /* Bit 2: Octets Tx OK Low CntOv*/
2363 XMT_OK_HI_OV
= 1<<1, /* Bit 1: Octets Tx OK Hi Cnt Ov*/
2364 XMT_OK_OV
= 1<<0, /* Bit 0: Frames Tx Ok Ov */
2367 #define XMT_DEF_MSK (XMT_OK_LO_OV | XMT_OK_HI_OV)
2369 struct skge_rx_desc
{
2382 struct skge_tx_desc
{
2394 struct skge_element
{
2395 struct skge_element
*next
;
2397 struct sk_buff
*skb
;
2398 DECLARE_PCI_UNMAP_ADDR(mapaddr
);
2399 DECLARE_PCI_UNMAP_LEN(maplen
);
2403 struct skge_element
*to_clean
;
2404 struct skge_element
*to_use
;
2405 struct skge_element
*start
;
2406 unsigned long count
;
2412 struct pci_dev
*pdev
;
2415 struct net_device
*dev
[2];
2426 struct work_struct phy_work
;
2427 struct mutex phy_mutex
;
2430 enum pause_control
{
2431 FLOW_MODE_NONE
= 1, /* No Flow-Control */
2432 FLOW_MODE_LOC_SEND
= 2, /* Local station sends PAUSE */
2433 FLOW_MODE_SYMMETRIC
= 3, /* Both stations may send PAUSE */
2434 FLOW_MODE_SYM_OR_REM
= 4, /* Both stations may send PAUSE or
2435 * just the remote station may send PAUSE
2440 FLOW_STAT_INDETERMINATED
=0, /* indeterminated */
2441 FLOW_STAT_NONE
, /* No Flow Control */
2442 FLOW_STAT_REM_SEND
, /* Remote Station sends PAUSE */
2443 FLOW_STAT_LOC_SEND
, /* Local station sends PAUSE */
2444 FLOW_STAT_SYMMETRIC
, /* Both station may send PAUSE */
2451 struct net_device
*netdev
;
2454 struct skge_ring tx_ring
;
2455 struct skge_ring rx_ring
;
2457 struct net_device_stats net_stats
;
2459 struct delayed_work link_thread
;
2460 enum pause_control flow_control
;
2461 enum pause_status flow_status
;
2465 u8 autoneg
; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
2466 u8 duplex
; /* DUPLEX_HALF, DUPLEX_FULL */
2467 u16 speed
; /* SPEED_1000, SPEED_100, ... */
2470 void *mem
; /* PCI memory for rings */
2472 unsigned long mem_size
;
2473 unsigned int rx_buf_size
;
2477 /* Register accessor for memory mapped device */
2478 static inline u32
skge_read32(const struct skge_hw
*hw
, int reg
)
2480 return readl(hw
->regs
+ reg
);
2483 static inline u16
skge_read16(const struct skge_hw
*hw
, int reg
)
2485 return readw(hw
->regs
+ reg
);
2488 static inline u8
skge_read8(const struct skge_hw
*hw
, int reg
)
2490 return readb(hw
->regs
+ reg
);
2493 static inline void skge_write32(const struct skge_hw
*hw
, int reg
, u32 val
)
2495 writel(val
, hw
->regs
+ reg
);
2498 static inline void skge_write16(const struct skge_hw
*hw
, int reg
, u16 val
)
2500 writew(val
, hw
->regs
+ reg
);
2503 static inline void skge_write8(const struct skge_hw
*hw
, int reg
, u8 val
)
2505 writeb(val
, hw
->regs
+ reg
);
2508 /* MAC Related Registers inside the device. */
2509 #define SK_REG(port,reg) (((port)<<7)+(u16)(reg))
2510 #define SK_XMAC_REG(port, reg) \
2511 ((BASE_XMAC_1 + (port) * (BASE_XMAC_2 - BASE_XMAC_1)) | (reg) << 1)
2513 static inline u32
xm_read32(const struct skge_hw
*hw
, int port
, int reg
)
2516 v
= skge_read16(hw
, SK_XMAC_REG(port
, reg
));
2517 v
|= (u32
)skge_read16(hw
, SK_XMAC_REG(port
, reg
+2)) << 16;
2521 static inline u16
xm_read16(const struct skge_hw
*hw
, int port
, int reg
)
2523 return skge_read16(hw
, SK_XMAC_REG(port
,reg
));
2526 static inline void xm_write32(const struct skge_hw
*hw
, int port
, int r
, u32 v
)
2528 skge_write16(hw
, SK_XMAC_REG(port
,r
), v
& 0xffff);
2529 skge_write16(hw
, SK_XMAC_REG(port
,r
+2), v
>> 16);
2532 static inline void xm_write16(const struct skge_hw
*hw
, int port
, int r
, u16 v
)
2534 skge_write16(hw
, SK_XMAC_REG(port
,r
), v
);
2537 static inline void xm_outhash(const struct skge_hw
*hw
, int port
, int reg
,
2540 xm_write16(hw
, port
, reg
, (u16
)hash
[0] | ((u16
)hash
[1] << 8));
2541 xm_write16(hw
, port
, reg
+2, (u16
)hash
[2] | ((u16
)hash
[3] << 8));
2542 xm_write16(hw
, port
, reg
+4, (u16
)hash
[4] | ((u16
)hash
[5] << 8));
2543 xm_write16(hw
, port
, reg
+6, (u16
)hash
[6] | ((u16
)hash
[7] << 8));
2546 static inline void xm_outaddr(const struct skge_hw
*hw
, int port
, int reg
,
2549 xm_write16(hw
, port
, reg
, (u16
)addr
[0] | ((u16
)addr
[1] << 8));
2550 xm_write16(hw
, port
, reg
+2, (u16
)addr
[2] | ((u16
)addr
[3] << 8));
2551 xm_write16(hw
, port
, reg
+4, (u16
)addr
[4] | ((u16
)addr
[5] << 8));
2554 #define SK_GMAC_REG(port,reg) \
2555 (BASE_GMAC_1 + (port) * (BASE_GMAC_2-BASE_GMAC_1) + (reg))
2557 static inline u16
gma_read16(const struct skge_hw
*hw
, int port
, int reg
)
2559 return skge_read16(hw
, SK_GMAC_REG(port
,reg
));
2562 static inline u32
gma_read32(const struct skge_hw
*hw
, int port
, int reg
)
2564 return (u32
) skge_read16(hw
, SK_GMAC_REG(port
,reg
))
2565 | ((u32
)skge_read16(hw
, SK_GMAC_REG(port
,reg
+4)) << 16);
2568 static inline void gma_write16(const struct skge_hw
*hw
, int port
, int r
, u16 v
)
2570 skge_write16(hw
, SK_GMAC_REG(port
,r
), v
);
2573 static inline void gma_set_addr(struct skge_hw
*hw
, int port
, int reg
,
2576 gma_write16(hw
, port
, reg
, (u16
) addr
[0] | ((u16
) addr
[1] << 8));
2577 gma_write16(hw
, port
, reg
+4,(u16
) addr
[2] | ((u16
) addr
[3] << 8));
2578 gma_write16(hw
, port
, reg
+8,(u16
) addr
[4] | ((u16
) addr
[5] << 8));