?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
ACPI: remove private acpica headers from driver files
[linux-2.6/mini2440.git] / drivers / ata / ata_piix.c
blobc11936e13dd3ccd39952b35b242e42dd5e0d1078
1 /*
2 * ata_piix.c - Intel PATA/SATA controllers
3 *
4 * Maintained by: Jeff Garzik <jgarzik@pobox.com>
5 * Please ALWAYS copy linux-ide@vger.kernel.org
6 * on emails.
7 *
8 *
9 * Copyright 2003-2005 Red Hat Inc
10 * Copyright 2003-2005 Jeff Garzik
11 *
12 *
13 * Copyright header from piix.c:
14 *
15 * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
16 * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
17 * Copyright (C) 2003 Red Hat Inc
18 *
19 *
20 * This program is free software; you can redistribute it and/or modify
21 * it under the terms of the GNU General Public License as published by
22 * the Free Software Foundation; either version 2, or (at your option)
23 * any later version.
24 *
25 * This program is distributed in the hope that it will be useful,
26 * but WITHOUT ANY WARRANTY; without even the implied warranty of
27 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
28 * GNU General Public License for more details.
29 *
30 * You should have received a copy of the GNU General Public License
31 * along with this program; see the file COPYING. If not, write to
32 * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
33 *
34 *
35 * libata documentation is available via 'make {ps|pdf}docs',
36 * as Documentation/DocBook/libata.*
37 *
38 * Hardware documentation available at http://developer.intel.com/
39 *
40 * Documentation
41 * Publically available from Intel web site. Errata documentation
42 * is also publically available. As an aide to anyone hacking on this
43 * driver the list of errata that are relevant is below, going back to
44 * PIIX4. Older device documentation is now a bit tricky to find.
45 *
46 * The chipsets all follow very much the same design. The orginal Triton
47 * series chipsets do _not_ support independant device timings, but this
48 * is fixed in Triton II. With the odd mobile exception the chips then
49 * change little except in gaining more modes until SATA arrives. This
50 * driver supports only the chips with independant timing (that is those
51 * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix
52 * for the early chip drivers.
53 *
54 * Errata of note:
55 *
56 * Unfixable
57 * PIIX4 errata #9 - Only on ultra obscure hw
58 * ICH3 errata #13 - Not observed to affect real hw
59 * by Intel
60 *
61 * Things we must deal with
62 * PIIX4 errata #10 - BM IDE hang with non UDMA
63 * (must stop/start dma to recover)
64 * 440MX errata #15 - As PIIX4 errata #10
65 * PIIX4 errata #15 - Must not read control registers
66 * during a PIO transfer
67 * 440MX errata #13 - As PIIX4 errata #15
68 * ICH2 errata #21 - DMA mode 0 doesn't work right
69 * ICH0/1 errata #55 - As ICH2 errata #21
70 * ICH2 spec c #9 - Extra operations needed to handle
71 * drive hotswap [NOT YET SUPPORTED]
72 * ICH2 spec c #20 - IDE PRD must not cross a 64K boundary
73 * and must be dword aligned
74 * ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3
75 *
76 * Should have been BIOS fixed:
77 * 450NX: errata #19 - DMA hangs on old 450NX
78 * 450NX: errata #20 - DMA hangs on old 450NX
79 * 450NX: errata #25 - Corruption with DMA on old 450NX
80 * ICH3 errata #15 - IDE deadlock under high load
81 * (BIOS must set dev 31 fn 0 bit 23)
82 * ICH3 errata #18 - Don't use native mode
83 */
84
85 #include <linux/kernel.h>
86 #include <linux/module.h>
87 #include <linux/pci.h>
88 #include <linux/init.h>
89 #include <linux/blkdev.h>
90 #include <linux/delay.h>
91 #include <linux/device.h>
92 #include <scsi/scsi_host.h>
93 #include <linux/libata.h>
94 #include <linux/dmi.h>
95
96 #define DRV_NAME "ata_piix"
97 #define DRV_VERSION "2.12"
98
99 enum {
100 PIIX_IOCFG = 0x54, /* IDE I/O configuration register */
101 ICH5_PMR = 0x90, /* port mapping register */
102 ICH5_PCS = 0x92, /* port control and status */
103 PIIX_SIDPR_BAR = 5,
104 PIIX_SIDPR_LEN = 16,
105 PIIX_SIDPR_IDX = 0,
106 PIIX_SIDPR_DATA = 4,
107
108 PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */
109 PIIX_FLAG_SIDPR = (1 << 29), /* SATA idx/data pair regs */
110
111 PIIX_PATA_FLAGS = ATA_FLAG_SLAVE_POSS,
112 PIIX_SATA_FLAGS = ATA_FLAG_SATA | PIIX_FLAG_CHECKINTR,
113
114 PIIX_80C_PRI = (1 << 5) | (1 << 4),
115 PIIX_80C_SEC = (1 << 7) | (1 << 6),
116
117 /* constants for mapping table */
118 P0 = 0, /* port 0 */
119 P1 = 1, /* port 1 */
120 P2 = 2, /* port 2 */
121 P3 = 3, /* port 3 */
122 IDE = -1, /* IDE */
123 NA = -2, /* not avaliable */
124 RV = -3, /* reserved */
125
126 PIIX_AHCI_DEVICE = 6,
127
128 /* host->flags bits */
129 PIIX_HOST_BROKEN_SUSPEND = (1 << 24),
130 };
131
132 enum piix_controller_ids {
133 /* controller IDs */
134 piix_pata_mwdma, /* PIIX3 MWDMA only */
135 piix_pata_33, /* PIIX4 at 33Mhz */
136 ich_pata_33, /* ICH up to UDMA 33 only */
137 ich_pata_66, /* ICH up to 66 Mhz */
138 ich_pata_100, /* ICH up to UDMA 100 */
139 ich5_sata,
140 ich6_sata,
141 ich6m_sata,
142 ich8_sata,
143 ich8_2port_sata,
144 ich8m_apple_sata, /* locks up on second port enable */
145 tolapai_sata,
146 piix_pata_vmw, /* PIIX4 for VMware, spurious DMA_ERR */
147 };
148
149 struct piix_map_db {
150 const u32 mask;
151 const u16 port_enable;
152 const int map[][4];
153 };
154
155 struct piix_host_priv {
156 const int *map;
157 void __iomem *sidpr;
158 };
159
160 static int piix_init_one(struct pci_dev *pdev,
161 const struct pci_device_id *ent);
162 static int piix_pata_prereset(struct ata_link *link, unsigned long deadline);
163 static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev);
164 static void piix_set_dmamode(struct ata_port *ap, struct ata_device *adev);
165 static void ich_set_dmamode(struct ata_port *ap, struct ata_device *adev);
166 static int ich_pata_cable_detect(struct ata_port *ap);
167 static u8 piix_vmw_bmdma_status(struct ata_port *ap);
168 static int piix_sidpr_scr_read(struct ata_link *link,
169 unsigned int reg, u32 *val);
170 static int piix_sidpr_scr_write(struct ata_link *link,
171 unsigned int reg, u32 val);
172 #ifdef CONFIG_PM
173 static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
174 static int piix_pci_device_resume(struct pci_dev *pdev);
175 #endif
176
177 static unsigned int in_module_init = 1;
178
179 static const struct pci_device_id piix_pci_tbl[] = {
180 /* Intel PIIX3 for the 430HX etc */
181 { 0x8086, 0x7010, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_mwdma },
182 /* VMware ICH4 */
183 { 0x8086, 0x7111, 0x15ad, 0x1976, 0, 0, piix_pata_vmw },
184 /* Intel PIIX4 for the 430TX/440BX/MX chipset: UDMA 33 */
185 /* Also PIIX4E (fn3 rev 2) and PIIX4M (fn3 rev 3) */
186 { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
187 /* Intel PIIX4 */
188 { 0x8086, 0x7199, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
189 /* Intel PIIX4 */
190 { 0x8086, 0x7601, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
191 /* Intel PIIX */
192 { 0x8086, 0x84CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
193 /* Intel ICH (i810, i815, i840) UDMA 66*/
194 { 0x8086, 0x2411, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_66 },
195 /* Intel ICH0 : UDMA 33*/
196 { 0x8086, 0x2421, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_33 },
197 /* Intel ICH2M */
198 { 0x8086, 0x244A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
199 /* Intel ICH2 (i810E2, i845, 850, 860) UDMA 100 */
200 { 0x8086, 0x244B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
201 /* Intel ICH3M */
202 { 0x8086, 0x248A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
203 /* Intel ICH3 (E7500/1) UDMA 100 */
204 { 0x8086, 0x248B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
205 /* Intel ICH4 (i845GV, i845E, i852, i855) UDMA 100 */
206 { 0x8086, 0x24CA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
207 { 0x8086, 0x24CB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
208 /* Intel ICH5 */
209 { 0x8086, 0x24DB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
210 /* C-ICH (i810E2) */
211 { 0x8086, 0x245B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
212 /* ESB (855GME/875P + 6300ESB) UDMA 100 */
213 { 0x8086, 0x25A2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
214 /* ICH6 (and 6) (i915) UDMA 100 */
215 { 0x8086, 0x266F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
216 /* ICH7/7-R (i945, i975) UDMA 100*/
217 { 0x8086, 0x27DF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
218 { 0x8086, 0x269E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
219 /* ICH8 Mobile PATA Controller */
220 { 0x8086, 0x2850, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich_pata_100 },
221
222 /* NOTE: The following PCI ids must be kept in sync with the
223 * list in drivers/pci/quirks.c.
224 */
225
226 /* 82801EB (ICH5) */
227 { 0x8086, 0x24d1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
228 /* 82801EB (ICH5) */
229 { 0x8086, 0x24df, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
230 /* 6300ESB (ICH5 variant with broken PCS present bits) */
231 { 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
232 /* 6300ESB pretending RAID */
233 { 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
234 /* 82801FB/FW (ICH6/ICH6W) */
235 { 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
236 /* 82801FR/FRW (ICH6R/ICH6RW) */
237 { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
238 /* 82801FBM ICH6M (ICH6R with only port 0 and 2 implemented).
239 * Attach iff the controller is in IDE mode. */
240 { 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID,
241 PCI_CLASS_STORAGE_IDE << 8, 0xffff00, ich6m_sata },
242 /* 82801GB/GR/GH (ICH7, identical to ICH6) */
243 { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
244 /* 2801GBM/GHM (ICH7M, identical to ICH6M) */
245 { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata },
246 /* Enterprise Southbridge 2 (631xESB/632xESB) */
247 { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
248 /* SATA Controller 1 IDE (ICH8) */
249 { 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
250 /* SATA Controller 2 IDE (ICH8) */
251 { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
252 /* Mobile SATA Controller IDE (ICH8M), Apple */
253 { 0x8086, 0x2828, 0x106b, 0x00a0, 0, 0, ich8m_apple_sata },
254 { 0x8086, 0x2828, 0x106b, 0x00a1, 0, 0, ich8m_apple_sata },
255 { 0x8086, 0x2828, 0x106b, 0x00a3, 0, 0, ich8m_apple_sata },
256 /* Mobile SATA Controller IDE (ICH8M) */
257 { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
258 /* SATA Controller IDE (ICH9) */
259 { 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
260 /* SATA Controller IDE (ICH9) */
261 { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
262 /* SATA Controller IDE (ICH9) */
263 { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
264 /* SATA Controller IDE (ICH9M) */
265 { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
266 /* SATA Controller IDE (ICH9M) */
267 { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
268 /* SATA Controller IDE (ICH9M) */
269 { 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
270 /* SATA Controller IDE (Tolapai) */
271 { 0x8086, 0x5028, PCI_ANY_ID, PCI_ANY_ID, 0, 0, tolapai_sata },
272 /* SATA Controller IDE (ICH10) */
273 { 0x8086, 0x3a00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
274 /* SATA Controller IDE (ICH10) */
275 { 0x8086, 0x3a06, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
276 /* SATA Controller IDE (ICH10) */
277 { 0x8086, 0x3a20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
278 /* SATA Controller IDE (ICH10) */
279 { 0x8086, 0x3a26, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
280 /* SATA Controller IDE (PCH) */
281 { 0x8086, 0x3b20, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
282 /* SATA Controller IDE (PCH) */
283 { 0x8086, 0x3b21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
284 /* SATA Controller IDE (PCH) */
285 { 0x8086, 0x3b26, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
286 /* SATA Controller IDE (PCH) */
287 { 0x8086, 0x3b28, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
288 /* SATA Controller IDE (PCH) */
289 { 0x8086, 0x3b2d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
290 /* SATA Controller IDE (PCH) */
291 { 0x8086, 0x3b2e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
292 { } /* terminate list */
293 };
294
295 static struct pci_driver piix_pci_driver = {
296 .name = DRV_NAME,
297 .id_table = piix_pci_tbl,
298 .probe = piix_init_one,
299 .remove = ata_pci_remove_one,
300 #ifdef CONFIG_PM
301 .suspend = piix_pci_device_suspend,
302 .resume = piix_pci_device_resume,
303 #endif
304 };
305
306 static struct scsi_host_template piix_sht = {
307 ATA_BMDMA_SHT(DRV_NAME),
308 };
309
310 static struct ata_port_operations piix_pata_ops = {
311 .inherits = &ata_bmdma_port_ops,
312 .cable_detect = ata_cable_40wire,
313 .set_piomode = piix_set_piomode,
314 .set_dmamode = piix_set_dmamode,
315 .prereset = piix_pata_prereset,
316 };
317
318 static struct ata_port_operations piix_vmw_ops = {
319 .inherits = &piix_pata_ops,
320 .bmdma_status = piix_vmw_bmdma_status,
321 };
322
323 static struct ata_port_operations ich_pata_ops = {
324 .inherits = &piix_pata_ops,
325 .cable_detect = ich_pata_cable_detect,
326 .set_dmamode = ich_set_dmamode,
327 };
328
329 static struct ata_port_operations piix_sata_ops = {
330 .inherits = &ata_bmdma_port_ops,
331 };
332
333 static struct ata_port_operations piix_sidpr_sata_ops = {
334 .inherits = &piix_sata_ops,
335 .hardreset = sata_std_hardreset,
336 .scr_read = piix_sidpr_scr_read,
337 .scr_write = piix_sidpr_scr_write,
338 };
339
340 static const struct piix_map_db ich5_map_db = {
341 .mask = 0x7,
342 .port_enable = 0x3,
343 .map = {
344 /* PM PS SM SS MAP */
345 { P0, NA, P1, NA }, /* 000b */
346 { P1, NA, P0, NA }, /* 001b */
347 { RV, RV, RV, RV },
348 { RV, RV, RV, RV },
349 { P0, P1, IDE, IDE }, /* 100b */
350 { P1, P0, IDE, IDE }, /* 101b */
351 { IDE, IDE, P0, P1 }, /* 110b */
352 { IDE, IDE, P1, P0 }, /* 111b */
353 },
354 };
355
356 static const struct piix_map_db ich6_map_db = {
357 .mask = 0x3,
358 .port_enable = 0xf,
359 .map = {
360 /* PM PS SM SS MAP */
361 { P0, P2, P1, P3 }, /* 00b */
362 { IDE, IDE, P1, P3 }, /* 01b */
363 { P0, P2, IDE, IDE }, /* 10b */
364 { RV, RV, RV, RV },
365 },
366 };
367
368 static const struct piix_map_db ich6m_map_db = {
369 .mask = 0x3,
370 .port_enable = 0x5,
371
372 /* Map 01b isn't specified in the doc but some notebooks use
373 * it anyway. MAP 01b have been spotted on both ICH6M and
374 * ICH7M.
375 */
376 .map = {
377 /* PM PS SM SS MAP */
378 { P0, P2, NA, NA }, /* 00b */
379 { IDE, IDE, P1, P3 }, /* 01b */
380 { P0, P2, IDE, IDE }, /* 10b */
381 { RV, RV, RV, RV },
382 },
383 };
384
385 static const struct piix_map_db ich8_map_db = {
386 .mask = 0x3,
387 .port_enable = 0xf,
388 .map = {
389 /* PM PS SM SS MAP */
390 { P0, P2, P1, P3 }, /* 00b (hardwired when in AHCI) */
391 { RV, RV, RV, RV },
392 { P0, P2, IDE, IDE }, /* 10b (IDE mode) */
393 { RV, RV, RV, RV },
394 },
395 };
396
397 static const struct piix_map_db ich8_2port_map_db = {
398 .mask = 0x3,
399 .port_enable = 0x3,
400 .map = {
401 /* PM PS SM SS MAP */
402 { P0, NA, P1, NA }, /* 00b */
403 { RV, RV, RV, RV }, /* 01b */
404 { RV, RV, RV, RV }, /* 10b */
405 { RV, RV, RV, RV },
406 },
407 };
408
409 static const struct piix_map_db ich8m_apple_map_db = {
410 .mask = 0x3,
411 .port_enable = 0x1,
412 .map = {
413 /* PM PS SM SS MAP */
414 { P0, NA, NA, NA }, /* 00b */
415 { RV, RV, RV, RV },
416 { P0, P2, IDE, IDE }, /* 10b */
417 { RV, RV, RV, RV },
418 },
419 };
420
421 static const struct piix_map_db tolapai_map_db = {
422 .mask = 0x3,
423 .port_enable = 0x3,
424 .map = {
425 /* PM PS SM SS MAP */
426 { P0, NA, P1, NA }, /* 00b */
427 { RV, RV, RV, RV }, /* 01b */
428 { RV, RV, RV, RV }, /* 10b */
429 { RV, RV, RV, RV },
430 },
431 };
432
433 static const struct piix_map_db *piix_map_db_table[] = {
434 [ich5_sata] = &ich5_map_db,
435 [ich6_sata] = &ich6_map_db,
436 [ich6m_sata] = &ich6m_map_db,
437 [ich8_sata] = &ich8_map_db,
438 [ich8_2port_sata] = &ich8_2port_map_db,
439 [ich8m_apple_sata] = &ich8m_apple_map_db,
440 [tolapai_sata] = &tolapai_map_db,
441 };
442
443 static struct ata_port_info piix_port_info[] = {
444 [piix_pata_mwdma] = /* PIIX3 MWDMA only */
445 {
446 .flags = PIIX_PATA_FLAGS,
447 .pio_mask = 0x1f, /* pio0-4 */
448 .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
449 .port_ops = &piix_pata_ops,
450 },
451
452 [piix_pata_33] = /* PIIX4 at 33MHz */
453 {
454 .flags = PIIX_PATA_FLAGS,
455 .pio_mask = 0x1f, /* pio0-4 */
456 .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
457 .udma_mask = ATA_UDMA_MASK_40C,
458 .port_ops = &piix_pata_ops,
459 },
460
461 [ich_pata_33] = /* ICH0 - ICH at 33Mhz*/
462 {
463 .flags = PIIX_PATA_FLAGS,
464 .pio_mask = 0x1f, /* pio 0-4 */
465 .mwdma_mask = 0x06, /* Check: maybe 0x07 */
466 .udma_mask = ATA_UDMA2, /* UDMA33 */
467 .port_ops = &ich_pata_ops,
468 },
469
470 [ich_pata_66] = /* ICH controllers up to 66MHz */
471 {
472 .flags = PIIX_PATA_FLAGS,
473 .pio_mask = 0x1f, /* pio 0-4 */
474 .mwdma_mask = 0x06, /* MWDMA0 is broken on chip */
475 .udma_mask = ATA_UDMA4,
476 .port_ops = &ich_pata_ops,
477 },
478
479 [ich_pata_100] =
480 {
481 .flags = PIIX_PATA_FLAGS | PIIX_FLAG_CHECKINTR,
482 .pio_mask = 0x1f, /* pio0-4 */
483 .mwdma_mask = 0x06, /* mwdma1-2 */
484 .udma_mask = ATA_UDMA5, /* udma0-5 */
485 .port_ops = &ich_pata_ops,
486 },
487
488 [ich5_sata] =
489 {
490 .flags = PIIX_SATA_FLAGS,
491 .pio_mask = 0x1f, /* pio0-4 */
492 .mwdma_mask = 0x07, /* mwdma0-2 */
493 .udma_mask = ATA_UDMA6,
494 .port_ops = &piix_sata_ops,
495 },
496
497 [ich6_sata] =
498 {
499 .flags = PIIX_SATA_FLAGS,
500 .pio_mask = 0x1f, /* pio0-4 */
501 .mwdma_mask = 0x07, /* mwdma0-2 */
502 .udma_mask = ATA_UDMA6,
503 .port_ops = &piix_sata_ops,
504 },
505
506 [ich6m_sata] =
507 {
508 .flags = PIIX_SATA_FLAGS,
509 .pio_mask = 0x1f, /* pio0-4 */
510 .mwdma_mask = 0x07, /* mwdma0-2 */
511 .udma_mask = ATA_UDMA6,
512 .port_ops = &piix_sata_ops,
513 },
514
515 [ich8_sata] =
516 {
517 .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR,
518 .pio_mask = 0x1f, /* pio0-4 */
519 .mwdma_mask = 0x07, /* mwdma0-2 */
520 .udma_mask = ATA_UDMA6,
521 .port_ops = &piix_sata_ops,
522 },
523
524 [ich8_2port_sata] =
525 {
526 .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SIDPR,
527 .pio_mask = 0x1f, /* pio0-4 */
528 .mwdma_mask = 0x07, /* mwdma0-2 */
529 .udma_mask = ATA_UDMA6,
530 .port_ops = &piix_sata_ops,
531 },
532
533 [tolapai_sata] =
534 {
535 .flags = PIIX_SATA_FLAGS,
536 .pio_mask = 0x1f, /* pio0-4 */
537 .mwdma_mask = 0x07, /* mwdma0-2 */
538 .udma_mask = ATA_UDMA6,
539 .port_ops = &piix_sata_ops,
540 },
541
542 [ich8m_apple_sata] =
543 {
544 .flags = PIIX_SATA_FLAGS,
545 .pio_mask = 0x1f, /* pio0-4 */
546 .mwdma_mask = 0x07, /* mwdma0-2 */
547 .udma_mask = ATA_UDMA6,
548 .port_ops = &piix_sata_ops,
549 },
550
551 [piix_pata_vmw] =
552 {
553 .flags = PIIX_PATA_FLAGS,
554 .pio_mask = 0x1f, /* pio0-4 */
555 .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
556 .udma_mask = ATA_UDMA_MASK_40C,
557 .port_ops = &piix_vmw_ops,
558 },
559
560 };
561
562 static struct pci_bits piix_enable_bits[] = {
563 { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
564 { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */
565 };
566
567 MODULE_AUTHOR("Andre Hedrick, Alan Cox, Andrzej Krzysztofowicz, Jeff Garzik");
568 MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers");
569 MODULE_LICENSE("GPL");
570 MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
571 MODULE_VERSION(DRV_VERSION);
572
573 struct ich_laptop {
574 u16 device;
575 u16 subvendor;
576 u16 subdevice;
577 };
578
579 /*
580 * List of laptops that use short cables rather than 80 wire
581 */
582
583 static const struct ich_laptop ich_laptop[] = {
584 /* devid, subvendor, subdev */
585 { 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
586 { 0x27DF, 0x1025, 0x0102 }, /* ICH7 on Acer 5602aWLMi */
587 { 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */
588 { 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */
589 { 0x27DF, 0x103C, 0x30A1 }, /* ICH7 on HP Compaq nc2400 */
590 { 0x27DF, 0x1071, 0xD221 }, /* ICH7 on Hercules EC-900 */
591 { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on ACER Aspire 2023WLMi */
592 { 0x24CA, 0x1025, 0x003d }, /* ICH4 on ACER TM290 */
593 { 0x266F, 0x1025, 0x0066 }, /* ICH6 on ACER Aspire 1694WLMi */
594 { 0x2653, 0x1043, 0x82D8 }, /* ICH6M on Asus Eee 701 */
595 /* end marker */
596 { 0, }
597 };
598
599 /**
600 * ich_pata_cable_detect - Probe host controller cable detect info
601 * @ap: Port for which cable detect info is desired
602 *
603 * Read 80c cable indicator from ATA PCI device's PCI config
604 * register. This register is normally set by firmware (BIOS).
605 *
606 * LOCKING:
607 * None (inherited from caller).
608 */
609
610 static int ich_pata_cable_detect(struct ata_port *ap)
611 {
612 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
613 const struct ich_laptop *lap = &ich_laptop[0];
614 u8 tmp, mask;
615
616 /* Check for specials - Acer Aspire 5602WLMi */
617 while (lap->device) {
618 if (lap->device == pdev->device &&
619 lap->subvendor == pdev->subsystem_vendor &&
620 lap->subdevice == pdev->subsystem_device)
621 return ATA_CBL_PATA40_SHORT;
622
623 lap++;
624 }
625
626 /* check BIOS cable detect results */
627 mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
628 pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
629 if ((tmp & mask) == 0)
630 return ATA_CBL_PATA40;
631 return ATA_CBL_PATA80;
632 }
633
634 /**
635 * piix_pata_prereset - prereset for PATA host controller
636 * @link: Target link
637 * @deadline: deadline jiffies for the operation
638 *
639 * LOCKING:
640 * None (inherited from caller).
641 */
642 static int piix_pata_prereset(struct ata_link *link, unsigned long deadline)
643 {
644 struct ata_port *ap = link->ap;
645 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
646
647 if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no]))
648 return -ENOENT;
649 return ata_sff_prereset(link, deadline);
650 }
651
652 /**
653 * piix_set_piomode - Initialize host controller PATA PIO timings
654 * @ap: Port whose timings we are configuring
655 * @adev: um
656 *
657 * Set PIO mode for device, in host controller PCI config space.
658 *
659 * LOCKING:
660 * None (inherited from caller).
661 */
662
663 static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev)
664 {
665 unsigned int pio = adev->pio_mode - XFER_PIO_0;
666 struct pci_dev *dev = to_pci_dev(ap->host->dev);
667 unsigned int is_slave = (adev->devno != 0);
668 unsigned int master_port= ap->port_no ? 0x42 : 0x40;
669 unsigned int slave_port = 0x44;
670 u16 master_data;
671 u8 slave_data;
672 u8 udma_enable;
673 int control = 0;
674
675 /*
676 * See Intel Document 298600-004 for the timing programing rules
677 * for ICH controllers.
678 */
679
680 static const /* ISP RTC */
681 u8 timings[][2] = { { 0, 0 },
682 { 0, 0 },
683 { 1, 0 },
684 { 2, 1 },
685 { 2, 3 }, };
686
687 if (pio >= 2)
688 control |= 1; /* TIME1 enable */
689 if (ata_pio_need_iordy(adev))
690 control |= 2; /* IE enable */
691
692 /* Intel specifies that the PPE functionality is for disk only */
693 if (adev->class == ATA_DEV_ATA)
694 control |= 4; /* PPE enable */
695
696 /* PIO configuration clears DTE unconditionally. It will be
697 * programmed in set_dmamode which is guaranteed to be called
698 * after set_piomode if any DMA mode is available.
699 */
700 pci_read_config_word(dev, master_port, &master_data);
701 if (is_slave) {
702 /* clear TIME1|IE1|PPE1|DTE1 */
703 master_data &= 0xff0f;
704 /* Enable SITRE (separate slave timing register) */
705 master_data |= 0x4000;
706 /* enable PPE1, IE1 and TIME1 as needed */
707 master_data |= (control << 4);
708 pci_read_config_byte(dev, slave_port, &slave_data);
709 slave_data &= (ap->port_no ? 0x0f : 0xf0);
710 /* Load the timing nibble for this slave */
711 slave_data |= ((timings[pio][0] << 2) | timings[pio][1])
712 << (ap->port_no ? 4 : 0);
713 } else {
714 /* clear ISP|RCT|TIME0|IE0|PPE0|DTE0 */
715 master_data &= 0xccf0;
716 /* Enable PPE, IE and TIME as appropriate */
717 master_data |= control;
718 /* load ISP and RCT */
719 master_data |=
720 (timings[pio][0] << 12) |
721 (timings[pio][1] << 8);
722 }
723 pci_write_config_word(dev, master_port, master_data);
724 if (is_slave)
725 pci_write_config_byte(dev, slave_port, slave_data);
726
727 /* Ensure the UDMA bit is off - it will be turned back on if
728 UDMA is selected */
729
730 if (ap->udma_mask) {
731 pci_read_config_byte(dev, 0x48, &udma_enable);
732 udma_enable &= ~(1 << (2 * ap->port_no + adev->devno));
733 pci_write_config_byte(dev, 0x48, udma_enable);
734 }
735 }
736
737 /**
738 * do_pata_set_dmamode - Initialize host controller PATA PIO timings
739 * @ap: Port whose timings we are configuring
740 * @adev: Drive in question
741 * @isich: set if the chip is an ICH device
742 *
743 * Set UDMA mode for device, in host controller PCI config space.
744 *
745 * LOCKING:
746 * None (inherited from caller).
747 */
748
749 static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, int isich)
750 {
751 struct pci_dev *dev = to_pci_dev(ap->host->dev);
752 u8 master_port = ap->port_no ? 0x42 : 0x40;
753 u16 master_data;
754 u8 speed = adev->dma_mode;
755 int devid = adev->devno + 2 * ap->port_no;
756 u8 udma_enable = 0;
757
758 static const /* ISP RTC */
759 u8 timings[][2] = { { 0, 0 },
760 { 0, 0 },
761 { 1, 0 },
762 { 2, 1 },
763 { 2, 3 }, };
764
765 pci_read_config_word(dev, master_port, &master_data);
766 if (ap->udma_mask)
767 pci_read_config_byte(dev, 0x48, &udma_enable);
768
769 if (speed >= XFER_UDMA_0) {
770 unsigned int udma = adev->dma_mode - XFER_UDMA_0;
771 u16 udma_timing;
772 u16 ideconf;
773 int u_clock, u_speed;
774
775 /*
776 * UDMA is handled by a combination of clock switching and
777 * selection of dividers
778 *
779 * Handy rule: Odd modes are UDMATIMx 01, even are 02
780 * except UDMA0 which is 00
781 */
782 u_speed = min(2 - (udma & 1), udma);
783 if (udma == 5)
784 u_clock = 0x1000; /* 100Mhz */
785 else if (udma > 2)
786 u_clock = 1; /* 66Mhz */
787 else
788 u_clock = 0; /* 33Mhz */
789
790 udma_enable |= (1 << devid);
791
792 /* Load the CT/RP selection */
793 pci_read_config_word(dev, 0x4A, &udma_timing);
794 udma_timing &= ~(3 << (4 * devid));
795 udma_timing |= u_speed << (4 * devid);
796 pci_write_config_word(dev, 0x4A, udma_timing);
797
798 if (isich) {
799 /* Select a 33/66/100Mhz clock */
800 pci_read_config_word(dev, 0x54, &ideconf);
801 ideconf &= ~(0x1001 << devid);
802 ideconf |= u_clock << devid;
803 /* For ICH or later we should set bit 10 for better
804 performance (WR_PingPong_En) */
805 pci_write_config_word(dev, 0x54, ideconf);
806 }
807 } else {
808 /*
809 * MWDMA is driven by the PIO timings. We must also enable
810 * IORDY unconditionally along with TIME1. PPE has already
811 * been set when the PIO timing was set.
812 */
813 unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
814 unsigned int control;
815 u8 slave_data;
816 const unsigned int needed_pio[3] = {
817 XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
818 };
819 int pio = needed_pio[mwdma] - XFER_PIO_0;
820
821 control = 3; /* IORDY|TIME1 */
822
823 /* If the drive MWDMA is faster than it can do PIO then
824 we must force PIO into PIO0 */
825
826 if (adev->pio_mode < needed_pio[mwdma])
827 /* Enable DMA timing only */
828 control |= 8; /* PIO cycles in PIO0 */
829
830 if (adev->devno) { /* Slave */
831 master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
832 master_data |= control << 4;
833 pci_read_config_byte(dev, 0x44, &slave_data);
834 slave_data &= (ap->port_no ? 0x0f : 0xf0);
835 /* Load the matching timing */
836 slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
837 pci_write_config_byte(dev, 0x44, slave_data);
838 } else { /* Master */
839 master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY
840 and master timing bits */
841 master_data |= control;
842 master_data |=
843 (timings[pio][0] << 12) |
844 (timings[pio][1] << 8);
845 }
846
847 if (ap->udma_mask) {
848 udma_enable &= ~(1 << devid);
849 pci_write_config_word(dev, master_port, master_data);
850 }
851 }
852 /* Don't scribble on 0x48 if the controller does not support UDMA */
853 if (ap->udma_mask)
854 pci_write_config_byte(dev, 0x48, udma_enable);
855 }
856
857 /**
858 * piix_set_dmamode - Initialize host controller PATA DMA timings
859 * @ap: Port whose timings we are configuring
860 * @adev: um
861 *
862 * Set MW/UDMA mode for device, in host controller PCI config space.
863 *
864 * LOCKING:
865 * None (inherited from caller).
866 */
867
868 static void piix_set_dmamode(struct ata_port *ap, struct ata_device *adev)
869 {
870 do_pata_set_dmamode(ap, adev, 0);
871 }
872
873 /**
874 * ich_set_dmamode - Initialize host controller PATA DMA timings
875 * @ap: Port whose timings we are configuring
876 * @adev: um
877 *
878 * Set MW/UDMA mode for device, in host controller PCI config space.
879 *
880 * LOCKING:
881 * None (inherited from caller).
882 */
883
884 static void ich_set_dmamode(struct ata_port *ap, struct ata_device *adev)
885 {
886 do_pata_set_dmamode(ap, adev, 1);
887 }
888
889 /*
890 * Serial ATA Index/Data Pair Superset Registers access
891 *
892 * Beginning from ICH8, there's a sane way to access SCRs using index
893 * and data register pair located at BAR5 which means that we have
894 * separate SCRs for master and slave. This is handled using libata
895 * slave_link facility.
896 */
897 static const int piix_sidx_map[] = {
898 [SCR_STATUS] = 0,
899 [SCR_ERROR] = 2,
900 [SCR_CONTROL] = 1,
901 };
902
903 static void piix_sidpr_sel(struct ata_link *link, unsigned int reg)
904 {
905 struct ata_port *ap = link->ap;
906 struct piix_host_priv *hpriv = ap->host->private_data;
907
908 iowrite32(((ap->port_no * 2 + link->pmp) << 8) | piix_sidx_map[reg],
909 hpriv->sidpr + PIIX_SIDPR_IDX);
910 }
911
912 static int piix_sidpr_scr_read(struct ata_link *link,
913 unsigned int reg, u32 *val)
914 {
915 struct piix_host_priv *hpriv = link->ap->host->private_data;
916
917 if (reg >= ARRAY_SIZE(piix_sidx_map))
918 return -EINVAL;
919
920 piix_sidpr_sel(link, reg);
921 *val = ioread32(hpriv->sidpr + PIIX_SIDPR_DATA);
922 return 0;
923 }
924
925 static int piix_sidpr_scr_write(struct ata_link *link,
926 unsigned int reg, u32 val)
927 {
928 struct piix_host_priv *hpriv = link->ap->host->private_data;
929
930 if (reg >= ARRAY_SIZE(piix_sidx_map))
931 return -EINVAL;
932
933 piix_sidpr_sel(link, reg);
934 iowrite32(val, hpriv->sidpr + PIIX_SIDPR_DATA);
935 return 0;
936 }
937
938 #ifdef CONFIG_PM
939 static int piix_broken_suspend(void)
940 {
941 static const struct dmi_system_id sysids[] = {
942 {
943 .ident = "TECRA M3",
944 .matches = {
945 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
946 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M3"),
947 },
948 },
949 {
950 .ident = "TECRA M3",
951 .matches = {
952 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
953 DMI_MATCH(DMI_PRODUCT_NAME, "Tecra M3"),
954 },
955 },
956 {
957 .ident = "TECRA M4",
958 .matches = {
959 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
960 DMI_MATCH(DMI_PRODUCT_NAME, "Tecra M4"),
961 },
962 },
963 {
964 .ident = "TECRA M4",
965 .matches = {
966 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
967 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M4"),
968 },
969 },
970 {
971 .ident = "TECRA M5",
972 .matches = {
973 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
974 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M5"),
975 },
976 },
977 {
978 .ident = "TECRA M6",
979 .matches = {
980 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
981 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M6"),
982 },
983 },
984 {
985 .ident = "TECRA M7",
986 .matches = {
987 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
988 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M7"),
989 },
990 },
991 {
992 .ident = "TECRA A8",
993 .matches = {
994 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
995 DMI_MATCH(DMI_PRODUCT_NAME, "TECRA A8"),
996 },
997 },
998 {
999 .ident = "Satellite R20",
1000 .matches = {
1001 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1002 DMI_MATCH(DMI_PRODUCT_NAME, "Satellite R20"),
1003 },
1004 },
1005 {
1006 .ident = "Satellite R25",
1007 .matches = {
1008 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1009 DMI_MATCH(DMI_PRODUCT_NAME, "Satellite R25"),
1010 },
1011 },
1012 {
1013 .ident = "Satellite U200",
1014 .matches = {
1015 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1016 DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U200"),
1017 },
1018 },
1019 {
1020 .ident = "Satellite U200",
1021 .matches = {
1022 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1023 DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE U200"),
1024 },
1025 },
1026 {
1027 .ident = "Satellite Pro U200",
1028 .matches = {
1029 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1030 DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE PRO U200"),
1031 },
1032 },
1033 {
1034 .ident = "Satellite U205",
1035 .matches = {
1036 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1037 DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
1038 },
1039 },
1040 {
1041 .ident = "SATELLITE U205",
1042 .matches = {
1043 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1044 DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE U205"),
1045 },
1046 },
1047 {
1048 .ident = "Portege M500",
1049 .matches = {
1050 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
1051 DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M500"),
1052 },
1053 },
1054
1055 { } /* terminate list */
1056 };
1057 static const char *oemstrs[] = {
1058 "Tecra M3,",
1059 };
1060 int i;
1061
1062 if (dmi_check_system(sysids))
1063 return 1;
1064
1065 for (i = 0; i < ARRAY_SIZE(oemstrs); i++)
1066 if (dmi_find_device(DMI_DEV_TYPE_OEM_STRING, oemstrs[i], NULL))
1067 return 1;
1068
1069 /* TECRA M4 sometimes forgets its identify and reports bogus
1070 * DMI information. As the bogus information is a bit
1071 * generic, match as many entries as possible. This manual
1072 * matching is necessary because dmi_system_id.matches is
1073 * limited to four entries.
1074 */
1075 if (dmi_get_system_info(DMI_SYS_VENDOR) &&
1076 dmi_get_system_info(DMI_PRODUCT_NAME) &&
1077 dmi_get_system_info(DMI_PRODUCT_VERSION) &&
1078 dmi_get_system_info(DMI_PRODUCT_SERIAL) &&
1079 dmi_get_system_info(DMI_BOARD_VENDOR) &&
1080 dmi_get_system_info(DMI_BOARD_NAME) &&
1081 dmi_get_system_info(DMI_BOARD_VERSION) &&
1082 !strcmp(dmi_get_system_info(DMI_SYS_VENDOR), "TOSHIBA") &&
1083 !strcmp(dmi_get_system_info(DMI_PRODUCT_NAME), "000000") &&
1084 !strcmp(dmi_get_system_info(DMI_PRODUCT_VERSION), "000000") &&
1085 !strcmp(dmi_get_system_info(DMI_PRODUCT_SERIAL), "000000") &&
1086 !strcmp(dmi_get_system_info(DMI_BOARD_VENDOR), "TOSHIBA") &&
1087 !strcmp(dmi_get_system_info(DMI_BOARD_NAME), "Portable PC") &&
1088 !strcmp(dmi_get_system_info(DMI_BOARD_VERSION), "Version A0"))
1089 return 1;
1090
1091 return 0;
1092 }
1093
1094 static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
1095 {
1096 struct ata_host *host = dev_get_drvdata(&pdev->dev);
1097 unsigned long flags;
1098 int rc = 0;
1099
1100 rc = ata_host_suspend(host, mesg);
1101 if (rc)
1102 return rc;
1103
1104 /* Some braindamaged ACPI suspend implementations expect the
1105 * controller to be awake on entry; otherwise, it burns cpu
1106 * cycles and power trying to do something to the sleeping
1107 * beauty.
1108 */
1109 if (piix_broken_suspend() && (mesg.event & PM_EVENT_SLEEP)) {
1110 pci_save_state(pdev);
1111
1112 /* mark its power state as "unknown", since we don't
1113 * know if e.g. the BIOS will change its device state
1114 * when we suspend.
1115 */
1116 if (pdev->current_state == PCI_D0)
1117 pdev->current_state = PCI_UNKNOWN;
1118
1119 /* tell resume that it's waking up from broken suspend */
1120 spin_lock_irqsave(&host->lock, flags);
1121 host->flags |= PIIX_HOST_BROKEN_SUSPEND;
1122 spin_unlock_irqrestore(&host->lock, flags);
1123 } else
1124 ata_pci_device_do_suspend(pdev, mesg);
1125
1126 return 0;
1127 }
1128
1129 static int piix_pci_device_resume(struct pci_dev *pdev)
1130 {
1131 struct ata_host *host = dev_get_drvdata(&pdev->dev);
1132 unsigned long flags;
1133 int rc;
1134
1135 if (host->flags & PIIX_HOST_BROKEN_SUSPEND) {
1136 spin_lock_irqsave(&host->lock, flags);
1137 host->flags &= ~PIIX_HOST_BROKEN_SUSPEND;
1138 spin_unlock_irqrestore(&host->lock, flags);
1139
1140 pci_set_power_state(pdev, PCI_D0);
1141 pci_restore_state(pdev);
1142
1143 /* PCI device wasn't disabled during suspend. Use
1144 * pci_reenable_device() to avoid affecting the enable
1145 * count.
1146 */
1147 rc = pci_reenable_device(pdev);
1148 if (rc)
1149 dev_printk(KERN_ERR, &pdev->dev, "failed to enable "
1150 "device after resume (%d)\n", rc);
1151 } else
1152 rc = ata_pci_device_do_resume(pdev);
1153
1154 if (rc == 0)
1155 ata_host_resume(host);
1156
1157 return rc;
1158 }
1159 #endif
1160
1161 static u8 piix_vmw_bmdma_status(struct ata_port *ap)
1162 {
1163 return ata_bmdma_status(ap) & ~ATA_DMA_ERR;
1164 }
1165
1166 #define AHCI_PCI_BAR 5
1167 #define AHCI_GLOBAL_CTL 0x04
1168 #define AHCI_ENABLE (1 << 31)
1169 static int piix_disable_ahci(struct pci_dev *pdev)
1170 {
1171 void __iomem *mmio;
1172 u32 tmp;
1173 int rc = 0;
1174
1175 /* BUG: pci_enable_device has not yet been called. This
1176 * works because this device is usually set up by BIOS.
1177 */
1178
1179 if (!pci_resource_start(pdev, AHCI_PCI_BAR) ||
1180 !pci_resource_len(pdev, AHCI_PCI_BAR))
1181 return 0;
1182
1183 mmio = pci_iomap(pdev, AHCI_PCI_BAR, 64);
1184 if (!mmio)
1185 return -ENOMEM;
1186
1187 tmp = ioread32(mmio + AHCI_GLOBAL_CTL);
1188 if (tmp & AHCI_ENABLE) {
1189 tmp &= ~AHCI_ENABLE;
1190 iowrite32(tmp, mmio + AHCI_GLOBAL_CTL);
1191
1192 tmp = ioread32(mmio + AHCI_GLOBAL_CTL);
1193 if (tmp & AHCI_ENABLE)
1194 rc = -EIO;
1195 }
1196
1197 pci_iounmap(pdev, mmio);
1198 return rc;
1199 }
1200
1201 /**
1202 * piix_check_450nx_errata - Check for problem 450NX setup
1203 * @ata_dev: the PCI device to check
1204 *
1205 * Check for the present of 450NX errata #19 and errata #25. If
1206 * they are found return an error code so we can turn off DMA
1207 */
1208
1209 static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev)
1210 {
1211 struct pci_dev *pdev = NULL;
1212 u16 cfg;
1213 int no_piix_dma = 0;
1214
1215 while ((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL) {
1216 /* Look for 450NX PXB. Check for problem configurations
1217 A PCI quirk checks bit 6 already */
1218 pci_read_config_word(pdev, 0x41, &cfg);
1219 /* Only on the original revision: IDE DMA can hang */
1220 if (pdev->revision == 0x00)
1221 no_piix_dma = 1;
1222 /* On all revisions below 5 PXB bus lock must be disabled for IDE */
1223 else if (cfg & (1<<14) && pdev->revision < 5)
1224 no_piix_dma = 2;
1225 }
1226 if (no_piix_dma)
1227 dev_printk(KERN_WARNING, &ata_dev->dev, "450NX errata present, disabling IDE DMA.\n");
1228 if (no_piix_dma == 2)
1229 dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n");
1230 return no_piix_dma;
1231 }
1232
1233 static void __devinit piix_init_pcs(struct ata_host *host,
1234 const struct piix_map_db *map_db)
1235 {
1236 struct pci_dev *pdev = to_pci_dev(host->dev);
1237 u16 pcs, new_pcs;
1238
1239 pci_read_config_word(pdev, ICH5_PCS, &pcs);
1240
1241 new_pcs = pcs | map_db->port_enable;
1242
1243 if (new_pcs != pcs) {
1244 DPRINTK("updating PCS from 0x%x to 0x%x\n", pcs, new_pcs);
1245 pci_write_config_word(pdev, ICH5_PCS, new_pcs);
1246 msleep(150);
1247 }
1248 }
1249
1250 static const int *__devinit piix_init_sata_map(struct pci_dev *pdev,
1251 struct ata_port_info *pinfo,
1252 const struct piix_map_db *map_db)
1253 {
1254 const int *map;
1255 int i, invalid_map = 0;
1256 u8 map_value;
1257
1258 pci_read_config_byte(pdev, ICH5_PMR, &map_value);
1259
1260 map = map_db->map[map_value & map_db->mask];
1261
1262 dev_printk(KERN_INFO, &pdev->dev, "MAP [");
1263 for (i = 0; i < 4; i++) {
1264 switch (map[i]) {
1265 case RV:
1266 invalid_map = 1;
1267 printk(" XX");
1268 break;
1269
1270 case NA:
1271 printk(" --");
1272 break;
1273
1274 case IDE:
1275 WARN_ON((i & 1) || map[i + 1] != IDE);
1276 pinfo[i / 2] = piix_port_info[ich_pata_100];
1277 i++;
1278 printk(" IDE IDE");
1279 break;
1280
1281 default:
1282 printk(" P%d", map[i]);
1283 if (i & 1)
1284 pinfo[i / 2].flags |= ATA_FLAG_SLAVE_POSS;
1285 break;
1286 }
1287 }
1288 printk(" ]\n");
1289
1290 if (invalid_map)
1291 dev_printk(KERN_ERR, &pdev->dev,
1292 "invalid MAP value %u\n", map_value);
1293
1294 return map;
1295 }
1296
1297 static int __devinit piix_init_sidpr(struct ata_host *host)
1298 {
1299 struct pci_dev *pdev = to_pci_dev(host->dev);
1300 struct piix_host_priv *hpriv = host->private_data;
1301 struct ata_link *link0 = &host->ports[0]->link;
1302 u32 scontrol;
1303 int i, rc;
1304
1305 /* check for availability */
1306 for (i = 0; i < 4; i++)
1307 if (hpriv->map[i] == IDE)
1308 return 0;
1309
1310 if (!(host->ports[0]->flags & PIIX_FLAG_SIDPR))
1311 return 0;
1312
1313 if (pci_resource_start(pdev, PIIX_SIDPR_BAR) == 0 ||
1314 pci_resource_len(pdev, PIIX_SIDPR_BAR) != PIIX_SIDPR_LEN)
1315 return 0;
1316
1317 if (pcim_iomap_regions(pdev, 1 << PIIX_SIDPR_BAR, DRV_NAME))
1318 return 0;
1319
1320 hpriv->sidpr = pcim_iomap_table(pdev)[PIIX_SIDPR_BAR];
1321
1322 /* SCR access via SIDPR doesn't work on some configurations.
1323 * Give it a test drive by inhibiting power save modes which
1324 * we'll do anyway.
1325 */
1326 piix_sidpr_scr_read(link0, SCR_CONTROL, &scontrol);
1327
1328 /* if IPM is already 3, SCR access is probably working. Don't
1329 * un-inhibit power save modes as BIOS might have inhibited
1330 * them for a reason.
1331 */
1332 if ((scontrol & 0xf00) != 0x300) {
1333 scontrol |= 0x300;
1334 piix_sidpr_scr_write(link0, SCR_CONTROL, scontrol);
1335 piix_sidpr_scr_read(link0, SCR_CONTROL, &scontrol);
1336
1337 if ((scontrol & 0xf00) != 0x300) {
1338 dev_printk(KERN_INFO, host->dev, "SCR access via "
1339 "SIDPR is available but doesn't work\n");
1340 return 0;
1341 }
1342 }
1343
1344 /* okay, SCRs available, set ops and ask libata for slave_link */
1345 for (i = 0; i < 2; i++) {
1346 struct ata_port *ap = host->ports[i];
1347
1348 ap->ops = &piix_sidpr_sata_ops;
1349
1350 if (ap->flags & ATA_FLAG_SLAVE_POSS) {
1351 rc = ata_slave_link_init(ap);
1352 if (rc)
1353 return rc;
1354 }
1355 }
1356
1357 return 0;
1358 }
1359
1360 static void piix_iocfg_bit18_quirk(struct pci_dev *pdev)
1361 {
1362 static const struct dmi_system_id sysids[] = {
1363 {
1364 /* Clevo M570U sets IOCFG bit 18 if the cdrom
1365 * isn't used to boot the system which
1366 * disables the channel.
1367 */
1368 .ident = "M570U",
1369 .matches = {
1370 DMI_MATCH(DMI_SYS_VENDOR, "Clevo Co."),
1371 DMI_MATCH(DMI_PRODUCT_NAME, "M570U"),
1372 },
1373 },
1374
1375 { } /* terminate list */
1376 };
1377 u32 iocfg;
1378
1379 if (!dmi_check_system(sysids))
1380 return;
1381
1382 /* The datasheet says that bit 18 is NOOP but certain systems
1383 * seem to use it to disable a channel. Clear the bit on the
1384 * affected systems.
1385 */
1386 pci_read_config_dword(pdev, PIIX_IOCFG, &iocfg);
1387 if (iocfg & (1 << 18)) {
1388 dev_printk(KERN_INFO, &pdev->dev,
1389 "applying IOCFG bit18 quirk\n");
1390 iocfg &= ~(1 << 18);
1391 pci_write_config_dword(pdev, PIIX_IOCFG, iocfg);
1392 }
1393 }
1394
1395 /**
1396 * piix_init_one - Register PIIX ATA PCI device with kernel services
1397 * @pdev: PCI device to register
1398 * @ent: Entry in piix_pci_tbl matching with @pdev
1399 *
1400 * Called from kernel PCI layer. We probe for combined mode (sigh),
1401 * and then hand over control to libata, for it to do the rest.
1402 *
1403 * LOCKING:
1404 * Inherited from PCI layer (may sleep).
1405 *
1406 * RETURNS:
1407 * Zero on success, or -ERRNO value.
1408 */
1409
1410 static int __devinit piix_init_one(struct pci_dev *pdev,
1411 const struct pci_device_id *ent)
1412 {
1413 static int printed_version;
1414 struct device *dev = &pdev->dev;
1415 struct ata_port_info port_info[2];
1416 const struct ata_port_info *ppi[] = { &port_info[0], &port_info[1] };
1417 unsigned long port_flags;
1418 struct ata_host *host;
1419 struct piix_host_priv *hpriv;
1420 int rc;
1421
1422 if (!printed_version++)
1423 dev_printk(KERN_DEBUG, &pdev->dev,
1424 "version " DRV_VERSION "\n");
1425
1426 /* no hotplugging support (FIXME) */
1427 if (!in_module_init)
1428 return -ENODEV;
1429
1430 port_info[0] = piix_port_info[ent->driver_data];
1431 port_info[1] = piix_port_info[ent->driver_data];
1432
1433 port_flags = port_info[0].flags;
1434
1435 /* enable device and prepare host */
1436 rc = pcim_enable_device(pdev);
1437 if (rc)
1438 return rc;
1439
1440 /* ICH6R may be driven by either ata_piix or ahci driver
1441 * regardless of BIOS configuration. Make sure AHCI mode is
1442 * off.
1443 */
1444 if (pdev->vendor == PCI_VENDOR_ID_INTEL && pdev->device == 0x2652) {
1445 rc = piix_disable_ahci(pdev);
1446 if (rc)
1447 return rc;
1448 }
1449
1450 /* SATA map init can change port_info, do it before prepping host */
1451 hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
1452 if (!hpriv)
1453 return -ENOMEM;
1454
1455 if (port_flags & ATA_FLAG_SATA)
1456 hpriv->map = piix_init_sata_map(pdev, port_info,
1457 piix_map_db_table[ent->driver_data]);
1458
1459 rc = ata_pci_sff_prepare_host(pdev, ppi, &host);
1460 if (rc)
1461 return rc;
1462 host->private_data = hpriv;
1463
1464 /* initialize controller */
1465 if (port_flags & ATA_FLAG_SATA) {
1466 piix_init_pcs(host, piix_map_db_table[ent->driver_data]);
1467 rc = piix_init_sidpr(host);
1468 if (rc)
1469 return rc;
1470 }
1471
1472 /* apply IOCFG bit18 quirk */
1473 piix_iocfg_bit18_quirk(pdev);
1474
1475 /* On ICH5, some BIOSen disable the interrupt using the
1476 * PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
1477 * On ICH6, this bit has the same effect, but only when
1478 * MSI is disabled (and it is disabled, as we don't use
1479 * message-signalled interrupts currently).
1480 */
1481 if (port_flags & PIIX_FLAG_CHECKINTR)
1482 pci_intx(pdev, 1);
1483
1484 if (piix_check_450nx_errata(pdev)) {
1485 /* This writes into the master table but it does not
1486 really matter for this errata as we will apply it to
1487 all the PIIX devices on the board */
1488 host->ports[0]->mwdma_mask = 0;
1489 host->ports[0]->udma_mask = 0;
1490 host->ports[1]->mwdma_mask = 0;
1491 host->ports[1]->udma_mask = 0;
1492 }
1493
1494 pci_set_master(pdev);
1495 return ata_pci_sff_activate_host(host, ata_sff_interrupt, &piix_sht);
1496 }
1497
1498 static int __init piix_init(void)
1499 {
1500 int rc;
1501
1502 DPRINTK("pci_register_driver\n");
1503 rc = pci_register_driver(&piix_pci_driver);
1504 if (rc)
1505 return rc;
1506
1507 in_module_init = 0;
1508
1509 DPRINTK("done\n");
1510 return 0;
1511 }
1512
1513 static void __exit piix_exit(void)
1514 {
1515 pci_unregister_driver(&piix_pci_driver);
1516 }
1517
1518 module_init(piix_init);
1519 module_exit(piix_exit);
Support for the Chinese Samsung S3C2440 based development boards