vt: add an activate and lock

[linux-2.6/mini2440.git] / drivers / mfd / ab3100-core.c

/*
 * Copyright (C) 2007-2009 ST-Ericsson
 * License terms: GNU General Public License (GPL) version 2
 * Low-level core for exclusive access to the AB3100 IC on the I2C bus
 * and some basic chip-configuration.
 * Author: Linus Walleij <linus.walleij@stericsson.com>
 */

#include <linux/i2c.h>
#include <linux/mutex.h>
#include <linux/list.h>
#include <linux/notifier.h>
#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/debugfs.h>
#include <linux/seq_file.h>
#include <linux/uaccess.h>
#include <linux/mfd/ab3100.h>

/* These are the only registers inside AB3100 used in this main file */

/* Interrupt event registers */
#define AB3100_EVENTA1          0x21
#define AB3100_EVENTA2          0x22
#define AB3100_EVENTA3          0x23

/* AB3100 DAC converter registers */
#define AB3100_DIS              0x00
#define AB3100_D0C              0x01
#define AB3100_D1C              0x02
#define AB3100_D2C              0x03
#define AB3100_D3C              0x04

/* Chip ID register */
#define AB3100_CID              0x20

/* AB3100 interrupt registers */
#define AB3100_IMRA1            0x24
#define AB3100_IMRA2            0x25
#define AB3100_IMRA3            0x26
#define AB3100_IMRB1            0x2B
#define AB3100_IMRB2            0x2C
#define AB3100_IMRB3            0x2D

/* System Power Monitoring and control registers */
#define AB3100_MCA              0x2E
#define AB3100_MCB              0x2F

/* SIM power up */
#define AB3100_SUP              0x50

/*
 * I2C communication
 *
 * The AB3100 is usually assigned address 0x48 (7-bit)
 * The chip is defined in the platform i2c_board_data section.
 */
static unsigned short normal_i2c[] = { 0x48, I2C_CLIENT_END };
I2C_CLIENT_INSMOD_1(ab3100);

u8 ab3100_get_chip_type(struct ab3100 *ab3100)
{
        u8 chip = ABUNKNOWN;

        switch (ab3100->chip_id & 0xf0) {
        case  0xa0:
                chip = AB3000;
                break;
        case  0xc0:
                chip = AB3100;
                break;
        }
        return chip;
}
EXPORT_SYMBOL(ab3100_get_chip_type);

int ab3100_set_register_interruptible(struct ab3100 *ab3100, u8 reg, u8 regval)
{
        u8 regandval[2] = {reg, regval};
        int err;

        err = mutex_lock_interruptible(&ab3100->access_mutex);
        if (err)
                return err;

        /*
         * A two-byte write message with the first byte containing the register
         * number and the second byte containing the value to be written
         * effectively sets a register in the AB3100.
         */
        err = i2c_master_send(ab3100->i2c_client, regandval, 2);
        if (err < 0) {
                dev_err(ab3100->dev,
                        "write error (write register): %d\n",
                        err);
        } else if (err != 2) {
                dev_err(ab3100->dev,
                        "write error (write register) "
                        "%d bytes transferred (expected 2)\n",
                        err);
                err = -EIO;
        } else {
                /* All is well */
                err = 0;
        }
        mutex_unlock(&ab3100->access_mutex);
        return err;
}
EXPORT_SYMBOL(ab3100_set_register_interruptible);


/*
 * The test registers exist at an I2C bus address up one
 * from the ordinary base. They are not supposed to be used
 * in production code, but sometimes you have to do that
 * anyway. It's currently only used from this file so declare
 * it static and do not export.
 */
static int ab3100_set_test_register_interruptible(struct ab3100 *ab3100,
                                    u8 reg, u8 regval)
{
        u8 regandval[2] = {reg, regval};
        int err;

        err = mutex_lock_interruptible(&ab3100->access_mutex);
        if (err)
                return err;

        err = i2c_master_send(ab3100->testreg_client, regandval, 2);
        if (err < 0) {
                dev_err(ab3100->dev,
                        "write error (write test register): %d\n",
                        err);
        } else if (err != 2) {
                dev_err(ab3100->dev,
                        "write error (write test register) "
                        "%d bytes transferred (expected 2)\n",
                        err);
                err = -EIO;
        } else {
                /* All is well */
                err = 0;
        }
        mutex_unlock(&ab3100->access_mutex);

        return err;
}


int ab3100_get_register_interruptible(struct ab3100 *ab3100, u8 reg, u8 *regval)
{
        int err;

        err = mutex_lock_interruptible(&ab3100->access_mutex);
        if (err)
                return err;

        /*
         * AB3100 require an I2C "stop" command between each message, else
         * it will not work. The only way of achieveing this with the
         * message transport layer is to send the read and write messages
         * separately.
         */
        err = i2c_master_send(ab3100->i2c_client, &reg, 1);
        if (err < 0) {
                dev_err(ab3100->dev,
                        "write error (send register address): %d\n",
                        err);
                goto get_reg_out_unlock;
        } else if (err != 1) {
                dev_err(ab3100->dev,
                        "write error (send register address) "
                        "%d bytes transferred (expected 1)\n",
                        err);
                err = -EIO;
                goto get_reg_out_unlock;
        } else {
                /* All is well */
                err = 0;
        }

        err = i2c_master_recv(ab3100->i2c_client, regval, 1);
        if (err < 0) {
                dev_err(ab3100->dev,
                        "write error (read register): %d\n",
                        err);
                goto get_reg_out_unlock;
        } else if (err != 1) {
                dev_err(ab3100->dev,
                        "write error (read register) "
                        "%d bytes transferred (expected 1)\n",
                        err);
                err = -EIO;
                goto get_reg_out_unlock;
        } else {
                /* All is well */
                err = 0;
        }

 get_reg_out_unlock:
        mutex_unlock(&ab3100->access_mutex);
        return err;
}
EXPORT_SYMBOL(ab3100_get_register_interruptible);


int ab3100_get_register_page_interruptible(struct ab3100 *ab3100,
                             u8 first_reg, u8 *regvals, u8 numregs)
{
        int err;

        if (ab3100->chip_id == 0xa0 ||
            ab3100->chip_id == 0xa1)
                /* These don't support paged reads */
                return -EIO;

        err = mutex_lock_interruptible(&ab3100->access_mutex);
        if (err)
                return err;

        /*
         * Paged read also require an I2C "stop" command.
         */
        err = i2c_master_send(ab3100->i2c_client, &first_reg, 1);
        if (err < 0) {
                dev_err(ab3100->dev,
                        "write error (send first register address): %d\n",
                        err);
                goto get_reg_page_out_unlock;
        } else if (err != 1) {
                dev_err(ab3100->dev,
                        "write error (send first register address) "
                        "%d bytes transferred (expected 1)\n",
                        err);
                err = -EIO;
                goto get_reg_page_out_unlock;
        }

        err = i2c_master_recv(ab3100->i2c_client, regvals, numregs);
        if (err < 0) {
                dev_err(ab3100->dev,
                        "write error (read register page): %d\n",
                        err);
                goto get_reg_page_out_unlock;
        } else if (err != numregs) {
                dev_err(ab3100->dev,
                        "write error (read register page) "
                        "%d bytes transferred (expected %d)\n",
                        err, numregs);
                err = -EIO;
                goto get_reg_page_out_unlock;
        }

        /* All is well */
        err = 0;

 get_reg_page_out_unlock:
        mutex_unlock(&ab3100->access_mutex);
        return err;
}
EXPORT_SYMBOL(ab3100_get_register_page_interruptible);


int ab3100_mask_and_set_register_interruptible(struct ab3100 *ab3100,
                                 u8 reg, u8 andmask, u8 ormask)
{
        u8 regandval[2] = {reg, 0};
        int err;

        err = mutex_lock_interruptible(&ab3100->access_mutex);
        if (err)
                return err;

        /* First read out the target register */
        err = i2c_master_send(ab3100->i2c_client, &reg, 1);
        if (err < 0) {
                dev_err(ab3100->dev,
                        "write error (maskset send address): %d\n",
                        err);
                goto get_maskset_unlock;
        } else if (err != 1) {
                dev_err(ab3100->dev,
                        "write error (maskset send address) "
                        "%d bytes transferred (expected 1)\n",
                        err);
                err = -EIO;
                goto get_maskset_unlock;
        }

        err = i2c_master_recv(ab3100->i2c_client, &regandval[1], 1);
        if (err < 0) {
                dev_err(ab3100->dev,
                        "write error (maskset read register): %d\n",
                        err);
                goto get_maskset_unlock;
        } else if (err != 1) {
                dev_err(ab3100->dev,
                        "write error (maskset read register) "
                        "%d bytes transferred (expected 1)\n",
                        err);
                err = -EIO;
                goto get_maskset_unlock;
        }

        /* Modify the register */
        regandval[1] &= andmask;
        regandval[1] |= ormask;

        /* Write the register */
        err = i2c_master_send(ab3100->i2c_client, regandval, 2);
        if (err < 0) {
                dev_err(ab3100->dev,
                        "write error (write register): %d\n",
                        err);
                goto get_maskset_unlock;
        } else if (err != 2) {
                dev_err(ab3100->dev,
                        "write error (write register) "
                        "%d bytes transferred (expected 2)\n",
                        err);
                err = -EIO;
                goto get_maskset_unlock;
        }

        /* All is well */
        err = 0;

 get_maskset_unlock:
        mutex_unlock(&ab3100->access_mutex);
        return err;
}
EXPORT_SYMBOL(ab3100_mask_and_set_register_interruptible);


/*
 * Register a simple callback for handling any AB3100 events.
 */
int ab3100_event_register(struct ab3100 *ab3100,
                          struct notifier_block *nb)
{
        return blocking_notifier_chain_register(&ab3100->event_subscribers,
                                               nb);
}
EXPORT_SYMBOL(ab3100_event_register);

/*
 * Remove a previously registered callback.
 */
int ab3100_event_unregister(struct ab3100 *ab3100,
                            struct notifier_block *nb)
{
  return blocking_notifier_chain_unregister(&ab3100->event_subscribers,
                                            nb);
}
EXPORT_SYMBOL(ab3100_event_unregister);


int ab3100_event_registers_startup_state_get(struct ab3100 *ab3100,
                                             u32 *fatevent)
{
        if (!ab3100->startup_events_read)
                return -EAGAIN; /* Try again later */
        *fatevent = ab3100->startup_events;
        return 0;
}
EXPORT_SYMBOL(ab3100_event_registers_startup_state_get);

/* Interrupt handling worker */
static void ab3100_work(struct work_struct *work)
{
        struct ab3100 *ab3100 = container_of(work, struct ab3100, work);
        u8 event_regs[3];
        u32 fatevent;
        int err;

        err = ab3100_get_register_page_interruptible(ab3100, AB3100_EVENTA1,
                                       event_regs, 3);
        if (err)
                goto err_event_wq;

        fatevent = (event_regs[0] << 16) |
                (event_regs[1] << 8) |
                event_regs[2];

        if (!ab3100->startup_events_read) {
                ab3100->startup_events = fatevent;
                ab3100->startup_events_read = true;
        }
        /*
         * The notified parties will have to mask out the events
         * they're interested in and react to them. They will be
         * notified on all events, then they use the fatevent value
         * to determine if they're interested.
         */
        blocking_notifier_call_chain(&ab3100->event_subscribers,
                                     fatevent, NULL);

        dev_dbg(ab3100->dev,
                "IRQ Event: 0x%08x\n", fatevent);

        /* By now the IRQ should be acked and deasserted so enable it again */
        enable_irq(ab3100->i2c_client->irq);
        return;

 err_event_wq:
        dev_dbg(ab3100->dev,
                "error in event workqueue\n");
        /* Enable the IRQ anyway, what choice do we have? */
        enable_irq(ab3100->i2c_client->irq);
        return;
}

static irqreturn_t ab3100_irq_handler(int irq, void *data)
{
        struct ab3100 *ab3100 = data;
        /*
         * Disable the IRQ and dispatch a worker to handle the
         * event. Since the chip resides on I2C this is slow
         * stuff and we will re-enable the interrupts once th
         * worker has finished.
         */
        disable_irq_nosync(irq);
        schedule_work(&ab3100->work);
        return IRQ_HANDLED;
}

#ifdef CONFIG_DEBUG_FS
/*
 * Some debugfs entries only exposed if we're using debug
 */
static int ab3100_registers_print(struct seq_file *s, void *p)
{
        struct ab3100 *ab3100 = s->private;
        u8 value;
        u8 reg;

        seq_printf(s, "AB3100 registers:\n");

        for (reg = 0; reg < 0xff; reg++) {
                ab3100_get_register_interruptible(ab3100, reg, &value);
                seq_printf(s, "[0x%x]:  0x%x\n", reg, value);
        }
        return 0;
}

static int ab3100_registers_open(struct inode *inode, struct file *file)
{
        return single_open(file, ab3100_registers_print, inode->i_private);
}

static const struct file_operations ab3100_registers_fops = {
        .open = ab3100_registers_open,
        .read = seq_read,
        .llseek = seq_lseek,
        .release = single_release,
        .owner = THIS_MODULE,
};

struct ab3100_get_set_reg_priv {
        struct ab3100 *ab3100;
        bool mode;
};

static int ab3100_get_set_reg_open_file(struct inode *inode, struct file *file)
{
        file->private_data = inode->i_private;
        return 0;
}

static ssize_t ab3100_get_set_reg(struct file *file,
                                  const char __user *user_buf,
                                  size_t count, loff_t *ppos)
{
        struct ab3100_get_set_reg_priv *priv = file->private_data;
        struct ab3100 *ab3100 = priv->ab3100;
        char buf[32];
        ssize_t buf_size;
        int regp;
        unsigned long user_reg;
        int err;
        int i = 0;

        /* Get userspace string and assure termination */
        buf_size = min(count, (sizeof(buf)-1));
        if (copy_from_user(buf, user_buf, buf_size))
                return -EFAULT;
        buf[buf_size] = 0;

        /*
         * The idea is here to parse a string which is either
         * "0xnn" for reading a register, or "0xaa 0xbb" for
         * writing 0xbb to the register 0xaa. First move past
         * whitespace and then begin to parse the register.
         */
        while ((i < buf_size) && (buf[i] == ' '))
                i++;
        regp = i;

        /*
         * Advance pointer to end of string then terminate
         * the register string. This is needed to satisfy
         * the strict_strtoul() function.
         */
        while ((i < buf_size) && (buf[i] != ' '))
                i++;
        buf[i] = '\0';

        err = strict_strtoul(&buf[regp], 16, &user_reg);
        if (err)
                return err;
        if (user_reg > 0xff)
                return -EINVAL;

        /* Either we read or we write a register here */
        if (!priv->mode) {
                /* Reading */
                u8 reg = (u8) user_reg;
                u8 regvalue;

                ab3100_get_register_interruptible(ab3100, reg, &regvalue);

                dev_info(ab3100->dev,
                         "debug read AB3100 reg[0x%02x]: 0x%02x\n",
                         reg, regvalue);
        } else {
                int valp;
                unsigned long user_value;
                u8 reg = (u8) user_reg;
                u8 value;
                u8 regvalue;

                /*
                 * Writing, we need some value to write to
                 * the register so keep parsing the string
                 * from userspace.
                 */
                i++;
                while ((i < buf_size) && (buf[i] == ' '))
                        i++;
                valp = i;
                while ((i < buf_size) && (buf[i] != ' '))
                        i++;
                buf[i] = '\0';

                err = strict_strtoul(&buf[valp], 16, &user_value);
                if (err)
                        return err;
                if (user_reg > 0xff)
                        return -EINVAL;

                value = (u8) user_value;
                ab3100_set_register_interruptible(ab3100, reg, value);
                ab3100_get_register_interruptible(ab3100, reg, &regvalue);

                dev_info(ab3100->dev,
                         "debug write reg[0x%02x] with 0x%02x, "
                         "after readback: 0x%02x\n",
                         reg, value, regvalue);
        }
        return buf_size;
}

static const struct file_operations ab3100_get_set_reg_fops = {
        .open = ab3100_get_set_reg_open_file,
        .write = ab3100_get_set_reg,
};

static struct dentry *ab3100_dir;
static struct dentry *ab3100_reg_file;
static struct ab3100_get_set_reg_priv ab3100_get_priv;
static struct dentry *ab3100_get_reg_file;
static struct ab3100_get_set_reg_priv ab3100_set_priv;
static struct dentry *ab3100_set_reg_file;

static void ab3100_setup_debugfs(struct ab3100 *ab3100)
{
        int err;

        ab3100_dir = debugfs_create_dir("ab3100", NULL);
        if (!ab3100_dir)
                goto exit_no_debugfs;

        ab3100_reg_file = debugfs_create_file("registers",
                                S_IRUGO, ab3100_dir, ab3100,
                                &ab3100_registers_fops);
        if (!ab3100_reg_file) {
                err = -ENOMEM;
                goto exit_destroy_dir;
        }

        ab3100_get_priv.ab3100 = ab3100;
        ab3100_get_priv.mode = false;
        ab3100_get_reg_file = debugfs_create_file("get_reg",
                                S_IWUGO, ab3100_dir, &ab3100_get_priv,
                                &ab3100_get_set_reg_fops);
        if (!ab3100_get_reg_file) {
                err = -ENOMEM;
                goto exit_destroy_reg;
        }

        ab3100_set_priv.ab3100 = ab3100;
        ab3100_set_priv.mode = true;
        ab3100_set_reg_file = debugfs_create_file("set_reg",
                                S_IWUGO, ab3100_dir, &ab3100_set_priv,
                                &ab3100_get_set_reg_fops);
        if (!ab3100_set_reg_file) {
                err = -ENOMEM;
                goto exit_destroy_get_reg;
        }
        return;

 exit_destroy_get_reg:
        debugfs_remove(ab3100_get_reg_file);
 exit_destroy_reg:
        debugfs_remove(ab3100_reg_file);
 exit_destroy_dir:
        debugfs_remove(ab3100_dir);
 exit_no_debugfs:
        return;
}
static inline void ab3100_remove_debugfs(void)
{
        debugfs_remove(ab3100_set_reg_file);
        debugfs_remove(ab3100_get_reg_file);
        debugfs_remove(ab3100_reg_file);
        debugfs_remove(ab3100_dir);
}
#else
static inline void ab3100_setup_debugfs(struct ab3100 *ab3100)
{
}
static inline void ab3100_remove_debugfs(void)
{
}
#endif

/*
 * Basic set-up, datastructure creation/destruction and I2C interface.
 * This sets up a default config in the AB3100 chip so that it
 * will work as expected.
 */

struct ab3100_init_setting {
        u8 abreg;
        u8 setting;
};

static const struct ab3100_init_setting __initdata
ab3100_init_settings[] = {
        {
                .abreg = AB3100_MCA,
                .setting = 0x01
        }, {
                .abreg = AB3100_MCB,
                .setting = 0x30
        }, {
                .abreg = AB3100_IMRA1,
                .setting = 0x00
        }, {
                .abreg = AB3100_IMRA2,
                .setting = 0xFF
        }, {
                .abreg = AB3100_IMRA3,
                .setting = 0x01
        }, {
                .abreg = AB3100_IMRB1,
                .setting = 0xBF
        }, {
                .abreg = AB3100_IMRB2,
                .setting = 0xFF
        }, {
                .abreg = AB3100_IMRB3,
                .setting = 0xFF
        }, {
                .abreg = AB3100_SUP,
                .setting = 0x00
        }, {
                .abreg = AB3100_DIS,
                .setting = 0xF0
        }, {
                .abreg = AB3100_D0C,
                .setting = 0x00
        }, {
                .abreg = AB3100_D1C,
                .setting = 0x00
        }, {
                .abreg = AB3100_D2C,
                .setting = 0x00
        }, {
                .abreg = AB3100_D3C,
                .setting = 0x00
        },
};

static int __init ab3100_setup(struct ab3100 *ab3100)
{
        int err = 0;
        int i;

        for (i = 0; i < ARRAY_SIZE(ab3100_init_settings); i++) {
                err = ab3100_set_register_interruptible(ab3100,
                                          ab3100_init_settings[i].abreg,
                                          ab3100_init_settings[i].setting);
                if (err)
                        goto exit_no_setup;
        }

        /*
         * Special trick to make the AB3100 use the 32kHz clock (RTC)
         * bit 3 in test register 0x02 is a special, undocumented test
         * register bit that only exist in AB3100 P1E
         */
        if (ab3100->chip_id == 0xc4) {
                dev_warn(ab3100->dev,
                         "AB3100 P1E variant detected, "
                         "forcing chip to 32KHz\n");
                err = ab3100_set_test_register_interruptible(ab3100, 0x02, 0x08);
        }

 exit_no_setup:
        return err;
}

/*
 * Here we define all the platform devices that appear
 * as children of the AB3100. These are regular platform
 * devices with the IORESOURCE_IO .start and .end set
 * to correspond to the internal AB3100 register range
 * mapping to the corresponding subdevice.
 */

#define AB3100_DEVICE(devname, devid)                           \
static struct platform_device ab3100_##devname##_device = {     \
        .name           = devid,                                \
        .id             = -1,                                   \
}

/*
 * This lists all the subdevices and corresponding register
 * ranges.
 */
AB3100_DEVICE(dac, "ab3100-dac");
AB3100_DEVICE(leds, "ab3100-leds");
AB3100_DEVICE(power, "ab3100-power");
AB3100_DEVICE(regulators, "ab3100-regulators");
AB3100_DEVICE(sim, "ab3100-sim");
AB3100_DEVICE(uart, "ab3100-uart");
AB3100_DEVICE(rtc, "ab3100-rtc");
AB3100_DEVICE(charger, "ab3100-charger");
AB3100_DEVICE(boost, "ab3100-boost");
AB3100_DEVICE(adc, "ab3100-adc");
AB3100_DEVICE(fuelgauge, "ab3100-fuelgauge");
AB3100_DEVICE(vibrator, "ab3100-vibrator");
AB3100_DEVICE(otp, "ab3100-otp");
AB3100_DEVICE(codec, "ab3100-codec");

static struct platform_device *
ab3100_platform_devs[] = {
        &ab3100_dac_device,
        &ab3100_leds_device,
        &ab3100_power_device,
        &ab3100_regulators_device,
        &ab3100_sim_device,
        &ab3100_uart_device,
        &ab3100_rtc_device,
        &ab3100_charger_device,
        &ab3100_boost_device,
        &ab3100_adc_device,
        &ab3100_fuelgauge_device,
        &ab3100_vibrator_device,
        &ab3100_otp_device,
        &ab3100_codec_device,
};

struct ab_family_id {
        u8      id;
        char    *name;
};

static const struct ab_family_id ids[] __initdata = {
        /* AB3100 */
        {
                .id = 0xc0,
                .name = "P1A"
        }, {
                .id = 0xc1,
                .name = "P1B"
        }, {
                .id = 0xc2,
                .name = "P1C"
        }, {
                .id = 0xc3,
                .name = "P1D"
        }, {
                .id = 0xc4,
                .name = "P1E"
        }, {
                .id = 0xc5,
                .name = "P1F/R1A"
        }, {
                .id = 0xc6,
                .name = "P1G/R1A"
        }, {
                .id = 0xc7,
                .name = "P2A/R2A"
        }, {
                .id = 0xc8,
                .name = "P2B/R2B"
        },
        /* AB3000 variants, not supported */
        {
                .id = 0xa0
        }, {
                .id = 0xa1
        }, {
                .id = 0xa2
        }, {
                .id = 0xa3
        }, {
                .id = 0xa4
        }, {
                .id = 0xa5
        }, {
                .id = 0xa6
        }, {
                .id = 0xa7
        },
        /* Terminator */
        {
                .id = 0x00,
        },
};

static int __init ab3100_probe(struct i2c_client *client,
                        const struct i2c_device_id *id)
{
        struct ab3100 *ab3100;
        struct ab3100_platform_data *ab3100_plf_data =
                client->dev.platform_data;
        int err;
        int i;

        ab3100 = kzalloc(sizeof(struct ab3100), GFP_KERNEL);
        if (!ab3100) {
                dev_err(&client->dev, "could not allocate AB3100 device\n");
                return -ENOMEM;
        }

        /* Initialize data structure */
        mutex_init(&ab3100->access_mutex);
        BLOCKING_INIT_NOTIFIER_HEAD(&ab3100->event_subscribers);

        ab3100->i2c_client = client;
        ab3100->dev = &ab3100->i2c_client->dev;

        i2c_set_clientdata(client, ab3100);

        /* Read chip ID register */
        err = ab3100_get_register_interruptible(ab3100, AB3100_CID,
                                                &ab3100->chip_id);
        if (err) {
                dev_err(&client->dev,
                        "could not communicate with the AB3100 analog "
                        "baseband chip\n");
                goto exit_no_detect;
        }

        for (i = 0; ids[i].id != 0x0; i++) {
                if (ids[i].id == ab3100->chip_id) {
                        if (ids[i].name != NULL) {
                                snprintf(&ab3100->chip_name[0],
                                         sizeof(ab3100->chip_name) - 1,
                                         "AB3100 %s",
                                         ids[i].name);
                                break;
                        } else {
                                dev_err(&client->dev,
                                        "AB3000 is not supported\n");
                                goto exit_no_detect;
                        }
                }
        }

        if (ids[i].id == 0x0) {
                dev_err(&client->dev, "unknown analog baseband chip id: 0x%x\n",
                        ab3100->chip_id);
                dev_err(&client->dev, "accepting it anyway. Please update "
                        "the driver.\n");
                goto exit_no_detect;
        }

        dev_info(&client->dev, "Detected chip: %s\n",
                 &ab3100->chip_name[0]);

        /* Attach a second dummy i2c_client to the test register address */
        ab3100->testreg_client = i2c_new_dummy(client->adapter,
                                                     client->addr + 1);
        if (!ab3100->testreg_client) {
                err = -ENOMEM;
                goto exit_no_testreg_client;
        }

        strlcpy(ab3100->testreg_client->name, id->name,
                sizeof(ab3100->testreg_client->name));

        err = ab3100_setup(ab3100);
        if (err)
                goto exit_no_setup;

        INIT_WORK(&ab3100->work, ab3100_work);

        /* This real unpredictable IRQ is of course sampled for entropy */
        err = request_irq(client->irq, ab3100_irq_handler,
                          IRQF_DISABLED | IRQF_SAMPLE_RANDOM,
                          "AB3100 IRQ", ab3100);
        if (err)
                goto exit_no_irq;

        /* Set parent and a pointer back to the container in device data */
        for (i = 0; i < ARRAY_SIZE(ab3100_platform_devs); i++) {
                ab3100_platform_devs[i]->dev.parent =
                        &client->dev;
                ab3100_platform_devs[i]->dev.platform_data =
                        ab3100_plf_data;
                platform_set_drvdata(ab3100_platform_devs[i], ab3100);
        }

        /* Register the platform devices */
        platform_add_devices(ab3100_platform_devs,
                             ARRAY_SIZE(ab3100_platform_devs));

        ab3100_setup_debugfs(ab3100);

        return 0;

 exit_no_irq:
 exit_no_setup:
        i2c_unregister_device(ab3100->testreg_client);
 exit_no_testreg_client:
 exit_no_detect:
        kfree(ab3100);
        return err;
}

static int __exit ab3100_remove(struct i2c_client *client)
{
        struct ab3100 *ab3100 = i2c_get_clientdata(client);
        int i;

        /* Unregister subdevices */
        for (i = 0; i < ARRAY_SIZE(ab3100_platform_devs); i++)
                platform_device_unregister(ab3100_platform_devs[i]);

        ab3100_remove_debugfs();
        i2c_unregister_device(ab3100->testreg_client);

        /*
         * At this point, all subscribers should have unregistered
         * their notifiers so deactivate IRQ
         */
        free_irq(client->irq, ab3100);
        kfree(ab3100);
        return 0;
}

static const struct i2c_device_id ab3100_id[] = {
        { "ab3100", ab3100 },
        { }
};
MODULE_DEVICE_TABLE(i2c, ab3100_id);

static struct i2c_driver ab3100_driver = {
        .driver = {
                .name   = "ab3100",
                .owner  = THIS_MODULE,
        },
        .id_table       = ab3100_id,
        .probe          = ab3100_probe,
        .remove         = __exit_p(ab3100_remove),
};

static int __init ab3100_i2c_init(void)
{
        return i2c_add_driver(&ab3100_driver);
}

static void __exit ab3100_i2c_exit(void)
{
        i2c_del_driver(&ab3100_driver);
}

subsys_initcall(ab3100_i2c_init);
module_exit(ab3100_i2c_exit);

MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>");
MODULE_DESCRIPTION("AB3100 core driver");
MODULE_LICENSE("GPL");