ide: falconide/q40ide - Use __ide_mm_{in,out}sw() for data
[linux-2.6/mini2440.git] / drivers / ata / pata_ns87415.c
blob773b1590b492d2bb647cd93547084c7f7465f4d6
1 /*
2 * pata_ns87415.c - NS87415 (non PARISC) PATA
4 * (C) 2005 Red Hat <alan@lxorguk.ukuu.org.uk>
6 * This is a fairly generic MWDMA controller. It has some limitations
7 * as it requires timing reloads on PIO/DMA transitions but it is otherwise
8 * fairly well designed.
10 * This driver assumes the firmware has left the chip in a valid ST506
11 * compliant state, either legacy IRQ 14/15 or native INTA shared. You
12 * may need to add platform code if your system fails to do this.
14 * The same cell appears in the 87560 controller used by some PARISC
15 * systems. This has its own special mountain of errata.
17 * TODO:
18 * Test PARISC SuperIO
19 * Get someone to test on SPARC
20 * Implement lazy pio/dma switching for better performance
21 * 8bit shared timing.
22 * See if we need to kill the FIFO for ATAPI
25 #include <linux/kernel.h>
26 #include <linux/module.h>
27 #include <linux/pci.h>
28 #include <linux/init.h>
29 #include <linux/blkdev.h>
30 #include <linux/delay.h>
31 #include <linux/device.h>
32 #include <scsi/scsi_host.h>
33 #include <linux/libata.h>
34 #include <linux/ata.h>
36 #define DRV_NAME "pata_ns87415"
37 #define DRV_VERSION "0.0.1"
39 /**
40 * ns87415_set_mode - Initialize host controller mode timings
41 * @ap: Port whose timings we are configuring
42 * @adev: Device whose timings we are configuring
43 * @mode: Mode to set
45 * Program the mode registers for this controller, channel and
46 * device. Because the chip is quite an old design we have to do this
47 * for PIO/DMA switches.
49 * LOCKING:
50 * None (inherited from caller).
53 static void ns87415_set_mode(struct ata_port *ap, struct ata_device *adev, u8 mode)
55 struct pci_dev *dev = to_pci_dev(ap->host->dev);
56 int unit = 2 * ap->port_no + adev->devno;
57 int timing = 0x44 + 2 * unit;
58 unsigned long T = 1000000000 / 33333; /* PCI clocks */
59 struct ata_timing t;
60 u16 clocking;
61 u8 iordy;
62 u8 status;
64 /* Timing register format is 17 - low nybble read timing with
65 the high nybble being 16 - x for recovery time in PCI clocks */
67 ata_timing_compute(adev, adev->pio_mode, &t, T, 0);
69 clocking = 17 - clamp_val(t.active, 2, 17);
70 clocking |= (16 - clamp_val(t.recover, 1, 16)) << 4;
71 /* Use the same timing for read and write bytes */
72 clocking |= (clocking << 8);
73 pci_write_config_word(dev, timing, clocking);
75 /* Set the IORDY enable versus DMA enable on or off properly */
76 pci_read_config_byte(dev, 0x42, &iordy);
77 iordy &= ~(1 << (4 + unit));
78 if (mode >= XFER_MW_DMA_0 || !ata_pio_need_iordy(adev))
79 iordy |= (1 << (4 + unit));
81 /* Paranoia: We shouldn't ever get here with busy write buffers
82 but if so wait */
84 pci_read_config_byte(dev, 0x43, &status);
85 while (status & 0x03) {
86 udelay(1);
87 pci_read_config_byte(dev, 0x43, &status);
89 /* Flip the IORDY/DMA bits now we are sure the write buffers are
90 clear */
91 pci_write_config_byte(dev, 0x42, iordy);
93 /* TODO: Set byte 54 command timing to the best 8bit
94 mode shared by all four devices */
97 /**
98 * ns87415_set_piomode - Initialize host controller PATA PIO timings
99 * @ap: Port whose timings we are configuring
100 * @adev: Device to program
102 * Set PIO mode for device, in host controller PCI config space.
104 * LOCKING:
105 * None (inherited from caller).
108 static void ns87415_set_piomode(struct ata_port *ap, struct ata_device *adev)
110 ns87415_set_mode(ap, adev, adev->pio_mode);
114 * ns87415_bmdma_setup - Set up DMA
115 * @qc: Command block
117 * Set up for bus masterng DMA. We have to do this ourselves
118 * rather than use the helper due to a chip erratum
121 static void ns87415_bmdma_setup(struct ata_queued_cmd *qc)
123 struct ata_port *ap = qc->ap;
124 unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
125 u8 dmactl;
127 /* load PRD table addr. */
128 mb(); /* make sure PRD table writes are visible to controller */
129 iowrite32(ap->prd_dma, ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS);
131 /* specify data direction, triple-check start bit is clear */
132 dmactl = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
133 dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
134 /* Due to an erratum we need to write these bits to the wrong
135 place - which does save us an I/O bizarrely */
136 dmactl |= ATA_DMA_INTR | ATA_DMA_ERR;
137 if (!rw)
138 dmactl |= ATA_DMA_WR;
139 iowrite8(dmactl, ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
140 /* issue r/w command */
141 ap->ops->sff_exec_command(ap, &qc->tf);
145 * ns87415_bmdma_start - Begin DMA transfer
146 * @qc: Command block
148 * Switch the timings for the chip and set up for a DMA transfer
149 * before the DMA burst begins.
151 * FIXME: We should do lazy switching on bmdma_start versus
152 * ata_pio_data_xfer for better performance.
155 static void ns87415_bmdma_start(struct ata_queued_cmd *qc)
157 ns87415_set_mode(qc->ap, qc->dev, qc->dev->dma_mode);
158 ata_bmdma_start(qc);
162 * ns87415_bmdma_stop - End DMA transfer
163 * @qc: Command block
165 * End DMA mode and switch the controller back into PIO mode
168 static void ns87415_bmdma_stop(struct ata_queued_cmd *qc)
170 ata_bmdma_stop(qc);
171 ns87415_set_mode(qc->ap, qc->dev, qc->dev->pio_mode);
175 * ns87415_irq_clear - Clear interrupt
176 * @ap: Channel to clear
178 * Erratum: Due to a chip bug regisers 02 and 0A bit 1 and 2 (the
179 * error bits) are reset by writing to register 00 or 08.
182 static void ns87415_irq_clear(struct ata_port *ap)
184 void __iomem *mmio = ap->ioaddr.bmdma_addr;
186 if (!mmio)
187 return;
188 iowrite8((ioread8(mmio + ATA_DMA_CMD) | ATA_DMA_INTR | ATA_DMA_ERR),
189 mmio + ATA_DMA_CMD);
193 * ns87415_check_atapi_dma - ATAPI DMA filter
194 * @qc: Command block
196 * Disable ATAPI DMA (for now). We may be able to do DMA if we
197 * kill the prefetching. This isn't clear.
200 static int ns87415_check_atapi_dma(struct ata_queued_cmd *qc)
202 return -EOPNOTSUPP;
205 #if defined(CONFIG_SUPERIO)
207 /* SUPERIO 87560 is a PoS chip that NatSem denies exists.
208 * Unfortunately, it's built-in on all Astro-based PA-RISC workstations
209 * which use the integrated NS87514 cell for CD-ROM support.
210 * i.e we have to support for CD-ROM installs.
211 * See drivers/parisc/superio.c for more gory details.
213 * Workarounds taken from drivers/ide/pci/ns87415.c
216 #include <asm/superio.h>
218 #define SUPERIO_IDE_MAX_RETRIES 25
221 * ns87560_read_buggy - workaround buggy Super I/O chip
222 * @port: Port to read
224 * Work around chipset problems in the 87560 SuperIO chip
227 static u8 ns87560_read_buggy(void __iomem *port)
229 u8 tmp;
230 int retries = SUPERIO_IDE_MAX_RETRIES;
231 do {
232 tmp = ioread8(port);
233 if (tmp != 0)
234 return tmp;
235 udelay(50);
236 } while(retries-- > 0);
237 return tmp;
241 * ns87560_check_status
242 * @ap: channel to check
244 * Return the status of the channel working around the
245 * 87560 flaws.
248 static u8 ns87560_check_status(struct ata_port *ap)
250 return ns87560_read_buggy(ap->ioaddr.status_addr);
254 * ns87560_tf_read - input device's ATA taskfile shadow registers
255 * @ap: Port from which input is read
256 * @tf: ATA taskfile register set for storing input
258 * Reads ATA taskfile registers for currently-selected device
259 * into @tf. Work around the 87560 bugs.
261 * LOCKING:
262 * Inherited from caller.
264 void ns87560_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
266 struct ata_ioports *ioaddr = &ap->ioaddr;
268 tf->command = ns87560_check_status(ap);
269 tf->feature = ioread8(ioaddr->error_addr);
270 tf->nsect = ioread8(ioaddr->nsect_addr);
271 tf->lbal = ioread8(ioaddr->lbal_addr);
272 tf->lbam = ioread8(ioaddr->lbam_addr);
273 tf->lbah = ioread8(ioaddr->lbah_addr);
274 tf->device = ns87560_read_buggy(ioaddr->device_addr);
276 if (tf->flags & ATA_TFLAG_LBA48) {
277 iowrite8(tf->ctl | ATA_HOB, ioaddr->ctl_addr);
278 tf->hob_feature = ioread8(ioaddr->error_addr);
279 tf->hob_nsect = ioread8(ioaddr->nsect_addr);
280 tf->hob_lbal = ioread8(ioaddr->lbal_addr);
281 tf->hob_lbam = ioread8(ioaddr->lbam_addr);
282 tf->hob_lbah = ioread8(ioaddr->lbah_addr);
283 iowrite8(tf->ctl, ioaddr->ctl_addr);
284 ap->last_ctl = tf->ctl;
289 * ns87560_bmdma_status
290 * @ap: channel to check
292 * Return the DMA status of the channel working around the
293 * 87560 flaws.
296 static u8 ns87560_bmdma_status(struct ata_port *ap)
298 return ns87560_read_buggy(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
300 #endif /* 87560 SuperIO Support */
302 static struct ata_port_operations ns87415_pata_ops = {
303 .inherits = &ata_bmdma_port_ops,
305 .check_atapi_dma = ns87415_check_atapi_dma,
306 .bmdma_setup = ns87415_bmdma_setup,
307 .bmdma_start = ns87415_bmdma_start,
308 .bmdma_stop = ns87415_bmdma_stop,
309 .sff_irq_clear = ns87415_irq_clear,
311 .cable_detect = ata_cable_40wire,
312 .set_piomode = ns87415_set_piomode,
315 #if defined(CONFIG_SUPERIO)
316 static struct ata_port_operations ns87560_pata_ops = {
317 .inherits = &ns87415_pata_ops,
318 .sff_tf_read = ns87560_tf_read,
319 .sff_check_status = ns87560_check_status,
320 .bmdma_status = ns87560_bmdma_status,
322 #endif
324 static struct scsi_host_template ns87415_sht = {
325 ATA_BMDMA_SHT(DRV_NAME),
330 * ns87415_init_one - Register 87415 ATA PCI device with kernel services
331 * @pdev: PCI device to register
332 * @ent: Entry in ns87415_pci_tbl matching with @pdev
334 * Called from kernel PCI layer. We probe for combined mode (sigh),
335 * and then hand over control to libata, for it to do the rest.
337 * LOCKING:
338 * Inherited from PCI layer (may sleep).
340 * RETURNS:
341 * Zero on success, or -ERRNO value.
344 static int ns87415_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
346 static int printed_version;
347 static const struct ata_port_info info = {
348 .flags = ATA_FLAG_SLAVE_POSS,
349 .pio_mask = ATA_PIO4,
350 .mwdma_mask = ATA_MWDMA2,
351 .port_ops = &ns87415_pata_ops,
353 const struct ata_port_info *ppi[] = { &info, NULL };
354 int rc;
355 #if defined(CONFIG_SUPERIO)
356 static const struct ata_port_info info87560 = {
357 .flags = ATA_FLAG_SLAVE_POSS,
358 .pio_mask = ATA_PIO4,
359 .mwdma_mask = ATA_MWDMA2,
360 .port_ops = &ns87560_pata_ops,
363 if (PCI_SLOT(pdev->devfn) == 0x0E)
364 ppi[0] = &info87560;
365 #endif
366 if (!printed_version++)
367 dev_printk(KERN_DEBUG, &pdev->dev,
368 "version " DRV_VERSION "\n");
370 rc = pcim_enable_device(pdev);
371 if (rc)
372 return rc;
374 /* Select 512 byte sectors */
375 pci_write_config_byte(pdev, 0x55, 0xEE);
376 /* Select PIO0 8bit clocking */
377 pci_write_config_byte(pdev, 0x54, 0xB7);
378 return ata_pci_sff_init_one(pdev, ppi, &ns87415_sht, NULL);
381 static const struct pci_device_id ns87415_pci_tbl[] = {
382 { PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_87415), },
384 { } /* terminate list */
387 static struct pci_driver ns87415_pci_driver = {
388 .name = DRV_NAME,
389 .id_table = ns87415_pci_tbl,
390 .probe = ns87415_init_one,
391 .remove = ata_pci_remove_one,
392 #ifdef CONFIG_PM
393 .suspend = ata_pci_device_suspend,
394 .resume = ata_pci_device_resume,
395 #endif
398 static int __init ns87415_init(void)
400 return pci_register_driver(&ns87415_pci_driver);
403 static void __exit ns87415_exit(void)
405 pci_unregister_driver(&ns87415_pci_driver);
408 module_init(ns87415_init);
409 module_exit(ns87415_exit);
411 MODULE_AUTHOR("Alan Cox");
412 MODULE_DESCRIPTION("ATA low-level driver for NS87415 controllers");
413 MODULE_LICENSE("GPL");
414 MODULE_DEVICE_TABLE(pci, ns87415_pci_tbl);
415 MODULE_VERSION(DRV_VERSION);