2 * Communication Processor Module v2.
4 * This file contains structures and information for the communication
5 * processor channels found in the dual port RAM or parameter RAM.
6 * All CPM control and status is available through the CPM2 internal
7 * memory map. See immap_cpm2.h for details.
13 #include <asm/immap_cpm2.h>
16 #ifdef CONFIG_PPC_85xx
17 #define CPM_MAP_ADDR (get_immrbase() + 0x80000)
20 /* CPM Command register.
22 #define CPM_CR_RST ((uint)0x80000000)
23 #define CPM_CR_PAGE ((uint)0x7c000000)
24 #define CPM_CR_SBLOCK ((uint)0x03e00000)
25 #define CPM_CR_FLG ((uint)0x00010000)
26 #define CPM_CR_MCN ((uint)0x00003fc0)
27 #define CPM_CR_OPCODE ((uint)0x0000000f)
29 /* Device sub-block and page codes.
31 #define CPM_CR_SCC1_SBLOCK (0x04)
32 #define CPM_CR_SCC2_SBLOCK (0x05)
33 #define CPM_CR_SCC3_SBLOCK (0x06)
34 #define CPM_CR_SCC4_SBLOCK (0x07)
35 #define CPM_CR_SMC1_SBLOCK (0x08)
36 #define CPM_CR_SMC2_SBLOCK (0x09)
37 #define CPM_CR_SPI_SBLOCK (0x0a)
38 #define CPM_CR_I2C_SBLOCK (0x0b)
39 #define CPM_CR_TIMER_SBLOCK (0x0f)
40 #define CPM_CR_RAND_SBLOCK (0x0e)
41 #define CPM_CR_FCC1_SBLOCK (0x10)
42 #define CPM_CR_FCC2_SBLOCK (0x11)
43 #define CPM_CR_FCC3_SBLOCK (0x12)
44 #define CPM_CR_IDMA1_SBLOCK (0x14)
45 #define CPM_CR_IDMA2_SBLOCK (0x15)
46 #define CPM_CR_IDMA3_SBLOCK (0x16)
47 #define CPM_CR_IDMA4_SBLOCK (0x17)
48 #define CPM_CR_MCC1_SBLOCK (0x1c)
50 #define CPM_CR_FCC_SBLOCK(x) (x + 0x10)
52 #define CPM_CR_SCC1_PAGE (0x00)
53 #define CPM_CR_SCC2_PAGE (0x01)
54 #define CPM_CR_SCC3_PAGE (0x02)
55 #define CPM_CR_SCC4_PAGE (0x03)
56 #define CPM_CR_SMC1_PAGE (0x07)
57 #define CPM_CR_SMC2_PAGE (0x08)
58 #define CPM_CR_SPI_PAGE (0x09)
59 #define CPM_CR_I2C_PAGE (0x0a)
60 #define CPM_CR_TIMER_PAGE (0x0a)
61 #define CPM_CR_RAND_PAGE (0x0a)
62 #define CPM_CR_FCC1_PAGE (0x04)
63 #define CPM_CR_FCC2_PAGE (0x05)
64 #define CPM_CR_FCC3_PAGE (0x06)
65 #define CPM_CR_IDMA1_PAGE (0x07)
66 #define CPM_CR_IDMA2_PAGE (0x08)
67 #define CPM_CR_IDMA3_PAGE (0x09)
68 #define CPM_CR_IDMA4_PAGE (0x0a)
69 #define CPM_CR_MCC1_PAGE (0x07)
70 #define CPM_CR_MCC2_PAGE (0x08)
72 #define CPM_CR_FCC_PAGE(x) (x + 0x04)
74 /* CPM2-specific opcodes (see cpm.h for common opcodes)
76 #define CPM_CR_START_IDMA ((ushort)0x0009)
78 #define mk_cr_cmd(PG, SBC, MCN, OP) \
79 ((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
81 #ifndef CONFIG_PPC_CPM_NEW_BINDING
82 /* Dual Port RAM addresses. The first 16K is available for almost
83 * any CPM use, so we put the BDs there. The first 128 bytes are
84 * used for SMC1 and SMC2 parameter RAM, so we start allocating
85 * BDs above that. All of this must change when we start
86 * downloading RAM microcode.
88 #define CPM_DATAONLY_BASE ((uint)128)
89 #define CPM_DP_NOSPACE ((uint)0x7fffffff)
90 #if defined(CONFIG_8272) || defined(CONFIG_MPC8555)
91 #define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE)
92 #define CPM_FCC_SPECIAL_BASE ((uint)0x00009000)
94 #define CPM_DATAONLY_SIZE ((uint)(16 * 1024) - CPM_DATAONLY_BASE)
95 #define CPM_FCC_SPECIAL_BASE ((uint)0x0000b000)
99 /* The number of pages of host memory we allocate for CPM. This is
100 * done early in kernel initialization to get physically contiguous
103 #define NUM_CPM_HOST_PAGES 2
105 /* Export the base address of the communication processor registers
108 extern cpm_cpm2_t __iomem
*cpmp
; /* Pointer to comm processor */
110 #ifdef CONFIG_PPC_CPM_NEW_BINDING
111 #define cpm_dpalloc cpm_muram_alloc
112 #define cpm_dpfree cpm_muram_free
113 #define cpm_dpram_addr cpm_muram_addr
115 extern unsigned long cpm_dpalloc(uint size
, uint align
);
116 extern int cpm_dpfree(unsigned long offset
);
117 extern unsigned long cpm_dpalloc_fixed(unsigned long offset
, uint size
, uint align
);
118 extern void cpm_dpdump(void);
119 extern void *cpm_dpram_addr(unsigned long offset
);
122 extern void cpm_setbrg(uint brg
, uint rate
);
123 extern void cpm2_fastbrg(uint brg
, uint rate
, int div16
);
124 extern void cpm2_reset(void);
126 /* Function code bits, usually generic to devices.
128 #define CPMFCR_GBL ((u_char)0x20) /* Set memory snooping */
129 #define CPMFCR_EB ((u_char)0x10) /* Set big endian byte order */
130 #define CPMFCR_TC2 ((u_char)0x04) /* Transfer code 2 value */
131 #define CPMFCR_DTB ((u_char)0x02) /* Use local bus for data when set */
132 #define CPMFCR_BDB ((u_char)0x01) /* Use local bus for BD when set */
134 /* Parameter RAM offsets from the base.
136 #define PROFF_SCC1 ((uint)0x8000)
137 #define PROFF_SCC2 ((uint)0x8100)
138 #define PROFF_SCC3 ((uint)0x8200)
139 #define PROFF_SCC4 ((uint)0x8300)
140 #define PROFF_FCC1 ((uint)0x8400)
141 #define PROFF_FCC2 ((uint)0x8500)
142 #define PROFF_FCC3 ((uint)0x8600)
143 #define PROFF_MCC1 ((uint)0x8700)
144 #define PROFF_SMC1_BASE ((uint)0x87fc)
145 #define PROFF_IDMA1_BASE ((uint)0x87fe)
146 #define PROFF_MCC2 ((uint)0x8800)
147 #define PROFF_SMC2_BASE ((uint)0x88fc)
148 #define PROFF_IDMA2_BASE ((uint)0x88fe)
149 #define PROFF_SPI_BASE ((uint)0x89fc)
150 #define PROFF_IDMA3_BASE ((uint)0x89fe)
151 #define PROFF_TIMERS ((uint)0x8ae0)
152 #define PROFF_REVNUM ((uint)0x8af0)
153 #define PROFF_RAND ((uint)0x8af8)
154 #define PROFF_I2C_BASE ((uint)0x8afc)
155 #define PROFF_IDMA4_BASE ((uint)0x8afe)
157 #define PROFF_SCC_SIZE ((uint)0x100)
158 #define PROFF_FCC_SIZE ((uint)0x100)
159 #define PROFF_SMC_SIZE ((uint)64)
161 /* The SMCs are relocated to any of the first eight DPRAM pages.
162 * We will fix these at the first locations of DPRAM, until we
163 * get some microcode patches :-).
164 * The parameter ram space for the SMCs is fifty-some bytes, and
165 * they are required to start on a 64 byte boundary.
167 #define PROFF_SMC1 (0)
168 #define PROFF_SMC2 (64)
171 /* Define enough so I can at least use the serial port as a UART.
173 typedef struct smc_uart
{
174 ushort smc_rbase
; /* Rx Buffer descriptor base address */
175 ushort smc_tbase
; /* Tx Buffer descriptor base address */
176 u_char smc_rfcr
; /* Rx function code */
177 u_char smc_tfcr
; /* Tx function code */
178 ushort smc_mrblr
; /* Max receive buffer length */
179 uint smc_rstate
; /* Internal */
180 uint smc_idp
; /* Internal */
181 ushort smc_rbptr
; /* Internal */
182 ushort smc_ibc
; /* Internal */
183 uint smc_rxtmp
; /* Internal */
184 uint smc_tstate
; /* Internal */
185 uint smc_tdp
; /* Internal */
186 ushort smc_tbptr
; /* Internal */
187 ushort smc_tbc
; /* Internal */
188 uint smc_txtmp
; /* Internal */
189 ushort smc_maxidl
; /* Maximum idle characters */
190 ushort smc_tmpidl
; /* Temporary idle counter */
191 ushort smc_brklen
; /* Last received break length */
192 ushort smc_brkec
; /* rcv'd break condition counter */
193 ushort smc_brkcr
; /* xmt break count register */
194 ushort smc_rmask
; /* Temporary bit mask */
195 uint smc_stmp
; /* SDMA Temp */
198 /* SMC uart mode register (Internal memory map).
200 #define SMCMR_REN ((ushort)0x0001)
201 #define SMCMR_TEN ((ushort)0x0002)
202 #define SMCMR_DM ((ushort)0x000c)
203 #define SMCMR_SM_GCI ((ushort)0x0000)
204 #define SMCMR_SM_UART ((ushort)0x0020)
205 #define SMCMR_SM_TRANS ((ushort)0x0030)
206 #define SMCMR_SM_MASK ((ushort)0x0030)
207 #define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */
208 #define SMCMR_REVD SMCMR_PM_EVEN
209 #define SMCMR_PEN ((ushort)0x0200) /* Parity enable */
210 #define SMCMR_BS SMCMR_PEN
211 #define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */
212 #define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */
213 #define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK)
215 /* SMC Event and Mask register.
217 #define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */
218 #define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */
219 #define SMCM_TXE ((unsigned char)0x10)
220 #define SMCM_BSY ((unsigned char)0x04)
221 #define SMCM_TX ((unsigned char)0x02)
222 #define SMCM_RX ((unsigned char)0x01)
224 /* Baud rate generators.
226 #define CPM_BRG_RST ((uint)0x00020000)
227 #define CPM_BRG_EN ((uint)0x00010000)
228 #define CPM_BRG_EXTC_INT ((uint)0x00000000)
229 #define CPM_BRG_EXTC_CLK3_9 ((uint)0x00004000)
230 #define CPM_BRG_EXTC_CLK5_15 ((uint)0x00008000)
231 #define CPM_BRG_ATB ((uint)0x00002000)
232 #define CPM_BRG_CD_MASK ((uint)0x00001ffe)
233 #define CPM_BRG_DIV16 ((uint)0x00000001)
237 #define SCC_GSMRH_IRP ((uint)0x00040000)
238 #define SCC_GSMRH_GDE ((uint)0x00010000)
239 #define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000)
240 #define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000)
241 #define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000)
242 #define SCC_GSMRH_REVD ((uint)0x00002000)
243 #define SCC_GSMRH_TRX ((uint)0x00001000)
244 #define SCC_GSMRH_TTX ((uint)0x00000800)
245 #define SCC_GSMRH_CDP ((uint)0x00000400)
246 #define SCC_GSMRH_CTSP ((uint)0x00000200)
247 #define SCC_GSMRH_CDS ((uint)0x00000100)
248 #define SCC_GSMRH_CTSS ((uint)0x00000080)
249 #define SCC_GSMRH_TFL ((uint)0x00000040)
250 #define SCC_GSMRH_RFW ((uint)0x00000020)
251 #define SCC_GSMRH_TXSY ((uint)0x00000010)
252 #define SCC_GSMRH_SYNL16 ((uint)0x0000000c)
253 #define SCC_GSMRH_SYNL8 ((uint)0x00000008)
254 #define SCC_GSMRH_SYNL4 ((uint)0x00000004)
255 #define SCC_GSMRH_RTSM ((uint)0x00000002)
256 #define SCC_GSMRH_RSYN ((uint)0x00000001)
258 #define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */
259 #define SCC_GSMRL_EDGE_NONE ((uint)0x60000000)
260 #define SCC_GSMRL_EDGE_NEG ((uint)0x40000000)
261 #define SCC_GSMRL_EDGE_POS ((uint)0x20000000)
262 #define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000)
263 #define SCC_GSMRL_TCI ((uint)0x10000000)
264 #define SCC_GSMRL_TSNC_3 ((uint)0x0c000000)
265 #define SCC_GSMRL_TSNC_4 ((uint)0x08000000)
266 #define SCC_GSMRL_TSNC_14 ((uint)0x04000000)
267 #define SCC_GSMRL_TSNC_INF ((uint)0x00000000)
268 #define SCC_GSMRL_RINV ((uint)0x02000000)
269 #define SCC_GSMRL_TINV ((uint)0x01000000)
270 #define SCC_GSMRL_TPL_128 ((uint)0x00c00000)
271 #define SCC_GSMRL_TPL_64 ((uint)0x00a00000)
272 #define SCC_GSMRL_TPL_48 ((uint)0x00800000)
273 #define SCC_GSMRL_TPL_32 ((uint)0x00600000)
274 #define SCC_GSMRL_TPL_16 ((uint)0x00400000)
275 #define SCC_GSMRL_TPL_8 ((uint)0x00200000)
276 #define SCC_GSMRL_TPL_NONE ((uint)0x00000000)
277 #define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000)
278 #define SCC_GSMRL_TPP_01 ((uint)0x00100000)
279 #define SCC_GSMRL_TPP_10 ((uint)0x00080000)
280 #define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000)
281 #define SCC_GSMRL_TEND ((uint)0x00040000)
282 #define SCC_GSMRL_TDCR_32 ((uint)0x00030000)
283 #define SCC_GSMRL_TDCR_16 ((uint)0x00020000)
284 #define SCC_GSMRL_TDCR_8 ((uint)0x00010000)
285 #define SCC_GSMRL_TDCR_1 ((uint)0x00000000)
286 #define SCC_GSMRL_RDCR_32 ((uint)0x0000c000)
287 #define SCC_GSMRL_RDCR_16 ((uint)0x00008000)
288 #define SCC_GSMRL_RDCR_8 ((uint)0x00004000)
289 #define SCC_GSMRL_RDCR_1 ((uint)0x00000000)
290 #define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000)
291 #define SCC_GSMRL_RENC_MANCH ((uint)0x00002000)
292 #define SCC_GSMRL_RENC_FM0 ((uint)0x00001000)
293 #define SCC_GSMRL_RENC_NRZI ((uint)0x00000800)
294 #define SCC_GSMRL_RENC_NRZ ((uint)0x00000000)
295 #define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600)
296 #define SCC_GSMRL_TENC_MANCH ((uint)0x00000400)
297 #define SCC_GSMRL_TENC_FM0 ((uint)0x00000200)
298 #define SCC_GSMRL_TENC_NRZI ((uint)0x00000100)
299 #define SCC_GSMRL_TENC_NRZ ((uint)0x00000000)
300 #define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */
301 #define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080)
302 #define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040)
303 #define SCC_GSMRL_DIAG_NORM ((uint)0x00000000)
304 #define SCC_GSMRL_ENR ((uint)0x00000020)
305 #define SCC_GSMRL_ENT ((uint)0x00000010)
306 #define SCC_GSMRL_MODE_ENET ((uint)0x0000000c)
307 #define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009)
308 #define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008)
309 #define SCC_GSMRL_MODE_V14 ((uint)0x00000007)
310 #define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006)
311 #define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005)
312 #define SCC_GSMRL_MODE_UART ((uint)0x00000004)
313 #define SCC_GSMRL_MODE_SS7 ((uint)0x00000003)
314 #define SCC_GSMRL_MODE_ATALK ((uint)0x00000002)
315 #define SCC_GSMRL_MODE_HDLC ((uint)0x00000000)
317 #define SCC_TODR_TOD ((ushort)0x8000)
319 /* SCC Event and Mask register.
321 #define SCCM_TXE ((unsigned char)0x10)
322 #define SCCM_BSY ((unsigned char)0x04)
323 #define SCCM_TX ((unsigned char)0x02)
324 #define SCCM_RX ((unsigned char)0x01)
326 typedef struct scc_param
{
327 ushort scc_rbase
; /* Rx Buffer descriptor base address */
328 ushort scc_tbase
; /* Tx Buffer descriptor base address */
329 u_char scc_rfcr
; /* Rx function code */
330 u_char scc_tfcr
; /* Tx function code */
331 ushort scc_mrblr
; /* Max receive buffer length */
332 uint scc_rstate
; /* Internal */
333 uint scc_idp
; /* Internal */
334 ushort scc_rbptr
; /* Internal */
335 ushort scc_ibc
; /* Internal */
336 uint scc_rxtmp
; /* Internal */
337 uint scc_tstate
; /* Internal */
338 uint scc_tdp
; /* Internal */
339 ushort scc_tbptr
; /* Internal */
340 ushort scc_tbc
; /* Internal */
341 uint scc_txtmp
; /* Internal */
342 uint scc_rcrc
; /* Internal */
343 uint scc_tcrc
; /* Internal */
346 /* CPM Ethernet through SCC1.
348 typedef struct scc_enet
{
350 uint sen_cpres
; /* Preset CRC */
351 uint sen_cmask
; /* Constant mask for CRC */
352 uint sen_crcec
; /* CRC Error counter */
353 uint sen_alec
; /* alignment error counter */
354 uint sen_disfc
; /* discard frame counter */
355 ushort sen_pads
; /* Tx short frame pad character */
356 ushort sen_retlim
; /* Retry limit threshold */
357 ushort sen_retcnt
; /* Retry limit counter */
358 ushort sen_maxflr
; /* maximum frame length register */
359 ushort sen_minflr
; /* minimum frame length register */
360 ushort sen_maxd1
; /* maximum DMA1 length */
361 ushort sen_maxd2
; /* maximum DMA2 length */
362 ushort sen_maxd
; /* Rx max DMA */
363 ushort sen_dmacnt
; /* Rx DMA counter */
364 ushort sen_maxb
; /* Max BD byte count */
365 ushort sen_gaddr1
; /* Group address filter */
369 uint sen_tbuf0data0
; /* Save area 0 - current frame */
370 uint sen_tbuf0data1
; /* Save area 1 - current frame */
371 uint sen_tbuf0rba
; /* Internal */
372 uint sen_tbuf0crc
; /* Internal */
373 ushort sen_tbuf0bcnt
; /* Internal */
374 ushort sen_paddrh
; /* physical address (MSB) */
376 ushort sen_paddrl
; /* physical address (LSB) */
377 ushort sen_pper
; /* persistence */
378 ushort sen_rfbdptr
; /* Rx first BD pointer */
379 ushort sen_tfbdptr
; /* Tx first BD pointer */
380 ushort sen_tlbdptr
; /* Tx last BD pointer */
381 uint sen_tbuf1data0
; /* Save area 0 - current frame */
382 uint sen_tbuf1data1
; /* Save area 1 - current frame */
383 uint sen_tbuf1rba
; /* Internal */
384 uint sen_tbuf1crc
; /* Internal */
385 ushort sen_tbuf1bcnt
; /* Internal */
386 ushort sen_txlen
; /* Tx Frame length counter */
387 ushort sen_iaddr1
; /* Individual address filter */
391 ushort sen_boffcnt
; /* Backoff counter */
393 /* NOTE: Some versions of the manual have the following items
394 * incorrectly documented. Below is the proper order.
396 ushort sen_taddrh
; /* temp address (MSB) */
398 ushort sen_taddrl
; /* temp address (LSB) */
402 /* SCC Event register as used by Ethernet.
404 #define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
405 #define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */
406 #define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */
407 #define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */
408 #define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
409 #define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */
411 /* SCC Mode Register (PSMR) as used by Ethernet.
413 #define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */
414 #define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */
415 #define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */
416 #define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */
417 #define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */
418 #define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */
419 #define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */
420 #define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */
421 #define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */
422 #define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */
423 #define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */
424 #define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */
425 #define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */
429 typedef struct scc_uart
{
431 uint scc_res1
; /* Reserved */
432 uint scc_res2
; /* Reserved */
433 ushort scc_maxidl
; /* Maximum idle chars */
434 ushort scc_idlc
; /* temp idle counter */
435 ushort scc_brkcr
; /* Break count register */
436 ushort scc_parec
; /* receive parity error counter */
437 ushort scc_frmec
; /* receive framing error counter */
438 ushort scc_nosec
; /* receive noise counter */
439 ushort scc_brkec
; /* receive break condition counter */
440 ushort scc_brkln
; /* last received break length */
441 ushort scc_uaddr1
; /* UART address character 1 */
442 ushort scc_uaddr2
; /* UART address character 2 */
443 ushort scc_rtemp
; /* Temp storage */
444 ushort scc_toseq
; /* Transmit out of sequence char */
445 ushort scc_char1
; /* control character 1 */
446 ushort scc_char2
; /* control character 2 */
447 ushort scc_char3
; /* control character 3 */
448 ushort scc_char4
; /* control character 4 */
449 ushort scc_char5
; /* control character 5 */
450 ushort scc_char6
; /* control character 6 */
451 ushort scc_char7
; /* control character 7 */
452 ushort scc_char8
; /* control character 8 */
453 ushort scc_rccm
; /* receive control character mask */
454 ushort scc_rccr
; /* receive control character register */
455 ushort scc_rlbc
; /* receive last break character */
458 /* SCC Event and Mask registers when it is used as a UART.
460 #define UART_SCCM_GLR ((ushort)0x1000)
461 #define UART_SCCM_GLT ((ushort)0x0800)
462 #define UART_SCCM_AB ((ushort)0x0200)
463 #define UART_SCCM_IDL ((ushort)0x0100)
464 #define UART_SCCM_GRA ((ushort)0x0080)
465 #define UART_SCCM_BRKE ((ushort)0x0040)
466 #define UART_SCCM_BRKS ((ushort)0x0020)
467 #define UART_SCCM_CCR ((ushort)0x0008)
468 #define UART_SCCM_BSY ((ushort)0x0004)
469 #define UART_SCCM_TX ((ushort)0x0002)
470 #define UART_SCCM_RX ((ushort)0x0001)
472 /* The SCC PSMR when used as a UART.
474 #define SCU_PSMR_FLC ((ushort)0x8000)
475 #define SCU_PSMR_SL ((ushort)0x4000)
476 #define SCU_PSMR_CL ((ushort)0x3000)
477 #define SCU_PSMR_UM ((ushort)0x0c00)
478 #define SCU_PSMR_FRZ ((ushort)0x0200)
479 #define SCU_PSMR_RZS ((ushort)0x0100)
480 #define SCU_PSMR_SYN ((ushort)0x0080)
481 #define SCU_PSMR_DRT ((ushort)0x0040)
482 #define SCU_PSMR_PEN ((ushort)0x0010)
483 #define SCU_PSMR_RPM ((ushort)0x000c)
484 #define SCU_PSMR_REVP ((ushort)0x0008)
485 #define SCU_PSMR_TPM ((ushort)0x0003)
486 #define SCU_PSMR_TEVP ((ushort)0x0002)
488 /* CPM Transparent mode SCC.
490 typedef struct scc_trans
{
492 uint st_cpres
; /* Preset CRC */
493 uint st_cmask
; /* Constant mask for CRC */
496 /* How about some FCCs.....
498 #define FCC_GFMR_DIAG_NORM ((uint)0x00000000)
499 #define FCC_GFMR_DIAG_LE ((uint)0x40000000)
500 #define FCC_GFMR_DIAG_AE ((uint)0x80000000)
501 #define FCC_GFMR_DIAG_ALE ((uint)0xc0000000)
502 #define FCC_GFMR_TCI ((uint)0x20000000)
503 #define FCC_GFMR_TRX ((uint)0x10000000)
504 #define FCC_GFMR_TTX ((uint)0x08000000)
505 #define FCC_GFMR_TTX ((uint)0x08000000)
506 #define FCC_GFMR_CDP ((uint)0x04000000)
507 #define FCC_GFMR_CTSP ((uint)0x02000000)
508 #define FCC_GFMR_CDS ((uint)0x01000000)
509 #define FCC_GFMR_CTSS ((uint)0x00800000)
510 #define FCC_GFMR_SYNL_NONE ((uint)0x00000000)
511 #define FCC_GFMR_SYNL_AUTO ((uint)0x00004000)
512 #define FCC_GFMR_SYNL_8 ((uint)0x00008000)
513 #define FCC_GFMR_SYNL_16 ((uint)0x0000c000)
514 #define FCC_GFMR_RTSM ((uint)0x00002000)
515 #define FCC_GFMR_RENC_NRZ ((uint)0x00000000)
516 #define FCC_GFMR_RENC_NRZI ((uint)0x00000800)
517 #define FCC_GFMR_REVD ((uint)0x00000400)
518 #define FCC_GFMR_TENC_NRZ ((uint)0x00000000)
519 #define FCC_GFMR_TENC_NRZI ((uint)0x00000100)
520 #define FCC_GFMR_TCRC_16 ((uint)0x00000000)
521 #define FCC_GFMR_TCRC_32 ((uint)0x00000080)
522 #define FCC_GFMR_ENR ((uint)0x00000020)
523 #define FCC_GFMR_ENT ((uint)0x00000010)
524 #define FCC_GFMR_MODE_ENET ((uint)0x0000000c)
525 #define FCC_GFMR_MODE_ATM ((uint)0x0000000a)
526 #define FCC_GFMR_MODE_HDLC ((uint)0x00000000)
528 /* Generic FCC parameter ram.
530 typedef struct fcc_param
{
531 ushort fcc_riptr
; /* Rx Internal temp pointer */
532 ushort fcc_tiptr
; /* Tx Internal temp pointer */
534 ushort fcc_mrblr
; /* Max receive buffer length, mod 32 bytes */
535 uint fcc_rstate
; /* Upper byte is Func code, must be set */
536 uint fcc_rbase
; /* Receive BD base */
537 ushort fcc_rbdstat
; /* RxBD status */
538 ushort fcc_rbdlen
; /* RxBD down counter */
539 uint fcc_rdptr
; /* RxBD internal data pointer */
540 uint fcc_tstate
; /* Upper byte is Func code, must be set */
541 uint fcc_tbase
; /* Transmit BD base */
542 ushort fcc_tbdstat
; /* TxBD status */
543 ushort fcc_tbdlen
; /* TxBD down counter */
544 uint fcc_tdptr
; /* TxBD internal data pointer */
545 uint fcc_rbptr
; /* Rx BD Internal buf pointer */
546 uint fcc_tbptr
; /* Tx BD Internal buf pointer */
547 uint fcc_rcrc
; /* Rx temp CRC */
549 uint fcc_tcrc
; /* Tx temp CRC */
553 /* Ethernet controller through FCC.
555 typedef struct fcc_enet
{
557 uint fen_statbuf
; /* Internal status buffer */
558 uint fen_camptr
; /* CAM address */
559 uint fen_cmask
; /* Constant mask for CRC */
560 uint fen_cpres
; /* Preset CRC */
561 uint fen_crcec
; /* CRC Error counter */
562 uint fen_alec
; /* alignment error counter */
563 uint fen_disfc
; /* discard frame counter */
564 ushort fen_retlim
; /* Retry limit */
565 ushort fen_retcnt
; /* Retry counter */
566 ushort fen_pper
; /* Persistence */
567 ushort fen_boffcnt
; /* backoff counter */
568 uint fen_gaddrh
; /* Group address filter, high 32-bits */
569 uint fen_gaddrl
; /* Group address filter, low 32-bits */
570 ushort fen_tfcstat
; /* out of sequence TxBD */
573 ushort fen_mflr
; /* Maximum frame length (1518) */
574 ushort fen_paddrh
; /* MAC address */
577 ushort fen_ibdcount
; /* Internal BD counter */
578 ushort fen_ibdstart
; /* Internal BD start pointer */
579 ushort fen_ibdend
; /* Internal BD end pointer */
580 ushort fen_txlen
; /* Internal Tx frame length counter */
581 uint fen_ibdbase
[8]; /* Internal use */
582 uint fen_iaddrh
; /* Individual address filter */
584 ushort fen_minflr
; /* Minimum frame length (64) */
585 ushort fen_taddrh
; /* Filter transfer MAC address */
588 ushort fen_padptr
; /* Pointer to pad byte buffer */
589 ushort fen_cftype
; /* control frame type */
590 ushort fen_cfrange
; /* control frame range */
591 ushort fen_maxb
; /* maximum BD count */
592 ushort fen_maxd1
; /* Max DMA1 length (1520) */
593 ushort fen_maxd2
; /* Max DMA2 length (1520) */
594 ushort fen_maxd
; /* internal max DMA count */
595 ushort fen_dmacnt
; /* internal DMA counter */
596 uint fen_octc
; /* Total octect counter */
597 uint fen_colc
; /* Total collision counter */
598 uint fen_broc
; /* Total broadcast packet counter */
599 uint fen_mulc
; /* Total multicast packet count */
600 uint fen_uspc
; /* Total packets < 64 bytes */
601 uint fen_frgc
; /* Total packets < 64 bytes with errors */
602 uint fen_ospc
; /* Total packets > 1518 */
603 uint fen_jbrc
; /* Total packets > 1518 with errors */
604 uint fen_p64c
; /* Total packets == 64 bytes */
605 uint fen_p65c
; /* Total packets 64 < bytes <= 127 */
606 uint fen_p128c
; /* Total packets 127 < bytes <= 255 */
607 uint fen_p256c
; /* Total packets 256 < bytes <= 511 */
608 uint fen_p512c
; /* Total packets 512 < bytes <= 1023 */
609 uint fen_p1024c
; /* Total packets 1024 < bytes <= 1518 */
610 uint fen_cambuf
; /* Internal CAM buffer poiner */
611 ushort fen_rfthr
; /* Received frames threshold */
612 ushort fen_rfcnt
; /* Received frames count */
615 /* FCC Event/Mask register as used by Ethernet.
617 #define FCC_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
618 #define FCC_ENET_RXC ((ushort)0x0040) /* Control Frame Received */
619 #define FCC_ENET_TXC ((ushort)0x0020) /* Out of seq. Tx sent */
620 #define FCC_ENET_TXE ((ushort)0x0010) /* Transmit Error */
621 #define FCC_ENET_RXF ((ushort)0x0008) /* Full frame received */
622 #define FCC_ENET_BSY ((ushort)0x0004) /* Busy. Rx Frame dropped */
623 #define FCC_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
624 #define FCC_ENET_RXB ((ushort)0x0001) /* A buffer was received */
626 /* FCC Mode Register (FPSMR) as used by Ethernet.
628 #define FCC_PSMR_HBC ((uint)0x80000000) /* Enable heartbeat */
629 #define FCC_PSMR_FC ((uint)0x40000000) /* Force Collision */
630 #define FCC_PSMR_SBT ((uint)0x20000000) /* Stop backoff timer */
631 #define FCC_PSMR_LPB ((uint)0x10000000) /* Local protect. 1 = FDX */
632 #define FCC_PSMR_LCW ((uint)0x08000000) /* Late collision select */
633 #define FCC_PSMR_FDE ((uint)0x04000000) /* Full Duplex Enable */
634 #define FCC_PSMR_MON ((uint)0x02000000) /* RMON Enable */
635 #define FCC_PSMR_PRO ((uint)0x00400000) /* Promiscuous Enable */
636 #define FCC_PSMR_FCE ((uint)0x00200000) /* Flow Control Enable */
637 #define FCC_PSMR_RSH ((uint)0x00100000) /* Receive Short Frames */
638 #define FCC_PSMR_CAM ((uint)0x00000400) /* CAM enable */
639 #define FCC_PSMR_BRO ((uint)0x00000200) /* Broadcast pkt discard */
640 #define FCC_PSMR_ENCRC ((uint)0x00000080) /* Use 32-bit CRC */
642 /* IIC parameter RAM.
645 ushort iic_rbase
; /* Rx Buffer descriptor base address */
646 ushort iic_tbase
; /* Tx Buffer descriptor base address */
647 u_char iic_rfcr
; /* Rx function code */
648 u_char iic_tfcr
; /* Tx function code */
649 ushort iic_mrblr
; /* Max receive buffer length */
650 uint iic_rstate
; /* Internal */
651 uint iic_rdp
; /* Internal */
652 ushort iic_rbptr
; /* Internal */
653 ushort iic_rbc
; /* Internal */
654 uint iic_rxtmp
; /* Internal */
655 uint iic_tstate
; /* Internal */
656 uint iic_tdp
; /* Internal */
657 ushort iic_tbptr
; /* Internal */
658 ushort iic_tbc
; /* Internal */
659 uint iic_txtmp
; /* Internal */
662 /* SPI parameter RAM.
665 ushort spi_rbase
; /* Rx Buffer descriptor base address */
666 ushort spi_tbase
; /* Tx Buffer descriptor base address */
667 u_char spi_rfcr
; /* Rx function code */
668 u_char spi_tfcr
; /* Tx function code */
669 ushort spi_mrblr
; /* Max receive buffer length */
670 uint spi_rstate
; /* Internal */
671 uint spi_rdp
; /* Internal */
672 ushort spi_rbptr
; /* Internal */
673 ushort spi_rbc
; /* Internal */
674 uint spi_rxtmp
; /* Internal */
675 uint spi_tstate
; /* Internal */
676 uint spi_tdp
; /* Internal */
677 ushort spi_tbptr
; /* Internal */
678 ushort spi_tbc
; /* Internal */
679 uint spi_txtmp
; /* Internal */
680 uint spi_res
; /* Tx temp. */
681 uint spi_res1
[4]; /* SDMA temp. */
684 /* SPI Mode register.
686 #define SPMODE_LOOP ((ushort)0x4000) /* Loopback */
687 #define SPMODE_CI ((ushort)0x2000) /* Clock Invert */
688 #define SPMODE_CP ((ushort)0x1000) /* Clock Phase */
689 #define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */
690 #define SPMODE_REV ((ushort)0x0400) /* Reversed Data */
691 #define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */
692 #define SPMODE_EN ((ushort)0x0100) /* Enable */
693 #define SPMODE_LENMSK ((ushort)0x00f0) /* character length */
694 #define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */
696 #define SPMODE_LEN(x) ((((x)-1)&0xF)<<4)
697 #define SPMODE_PM(x) ((x) &0xF)
699 #define SPI_EB ((u_char)0x10) /* big endian byte order */
701 /* IDMA parameter RAM
703 typedef struct idma
{
704 ushort ibase
; /* IDMA buffer descriptor table base address */
705 ushort dcm
; /* DMA channel mode */
706 ushort ibdptr
; /* IDMA current buffer descriptor pointer */
707 ushort dpr_buf
; /* IDMA transfer buffer base address */
708 ushort buf_inv
; /* internal buffer inventory */
709 ushort ss_max
; /* steady-state maximum transfer size */
710 ushort dpr_in_ptr
; /* write pointer inside the internal buffer */
711 ushort sts
; /* source transfer size */
712 ushort dpr_out_ptr
; /* read pointer inside the internal buffer */
713 ushort seob
; /* source end of burst */
714 ushort deob
; /* destination end of burst */
715 ushort dts
; /* destination transfer size */
716 ushort ret_add
; /* return address when working in ERM=1 mode */
717 ushort res0
; /* reserved */
718 uint bd_cnt
; /* internal byte count */
719 uint s_ptr
; /* source internal data pointer */
720 uint d_ptr
; /* destination internal data pointer */
721 uint istate
; /* internal state */
722 u_char res1
[20]; /* pad to 64-byte length */
725 /* DMA channel mode bit fields
727 #define IDMA_DCM_FB ((ushort)0x8000) /* fly-by mode */
728 #define IDMA_DCM_LP ((ushort)0x4000) /* low priority */
729 #define IDMA_DCM_TC2 ((ushort)0x0400) /* value driven on TC[2] */
730 #define IDMA_DCM_DMA_WRAP_MASK ((ushort)0x01c0) /* mask for DMA wrap */
731 #define IDMA_DCM_DMA_WRAP_64 ((ushort)0x0000) /* 64-byte DMA xfer buffer */
732 #define IDMA_DCM_DMA_WRAP_128 ((ushort)0x0040) /* 128-byte DMA xfer buffer */
733 #define IDMA_DCM_DMA_WRAP_256 ((ushort)0x0080) /* 256-byte DMA xfer buffer */
734 #define IDMA_DCM_DMA_WRAP_512 ((ushort)0x00c0) /* 512-byte DMA xfer buffer */
735 #define IDMA_DCM_DMA_WRAP_1024 ((ushort)0x0100) /* 1024-byte DMA xfer buffer */
736 #define IDMA_DCM_DMA_WRAP_2048 ((ushort)0x0140) /* 2048-byte DMA xfer buffer */
737 #define IDMA_DCM_SINC ((ushort)0x0020) /* source inc addr */
738 #define IDMA_DCM_DINC ((ushort)0x0010) /* destination inc addr */
739 #define IDMA_DCM_ERM ((ushort)0x0008) /* external request mode */
740 #define IDMA_DCM_DT ((ushort)0x0004) /* DONE treatment */
741 #define IDMA_DCM_SD_MASK ((ushort)0x0003) /* mask for SD bit field */
742 #define IDMA_DCM_SD_MEM2MEM ((ushort)0x0000) /* memory-to-memory xfer */
743 #define IDMA_DCM_SD_PER2MEM ((ushort)0x0002) /* peripheral-to-memory xfer */
744 #define IDMA_DCM_SD_MEM2PER ((ushort)0x0001) /* memory-to-peripheral xfer */
746 /* IDMA Buffer Descriptors
748 typedef struct idma_bd
{
750 uint len
; /* data length */
751 uint src
; /* source data buffer pointer */
752 uint dst
; /* destination data buffer pointer */
755 /* IDMA buffer descriptor flag bit fields
757 #define IDMA_BD_V ((uint)0x80000000) /* valid */
758 #define IDMA_BD_W ((uint)0x20000000) /* wrap */
759 #define IDMA_BD_I ((uint)0x10000000) /* interrupt */
760 #define IDMA_BD_L ((uint)0x08000000) /* last */
761 #define IDMA_BD_CM ((uint)0x02000000) /* continuous mode */
762 #define IDMA_BD_SDN ((uint)0x00400000) /* source done */
763 #define IDMA_BD_DDN ((uint)0x00200000) /* destination done */
764 #define IDMA_BD_DGBL ((uint)0x00100000) /* destination global */
765 #define IDMA_BD_DBO_LE ((uint)0x00040000) /* little-end dest byte order */
766 #define IDMA_BD_DBO_BE ((uint)0x00080000) /* big-end dest byte order */
767 #define IDMA_BD_DDTB ((uint)0x00010000) /* destination data bus */
768 #define IDMA_BD_SGBL ((uint)0x00002000) /* source global */
769 #define IDMA_BD_SBO_LE ((uint)0x00000800) /* little-end src byte order */
770 #define IDMA_BD_SBO_BE ((uint)0x00001000) /* big-end src byte order */
771 #define IDMA_BD_SDTB ((uint)0x00000200) /* source data bus */
773 /* per-channel IDMA registers
775 typedef struct im_idma
{
776 u_char idsr
; /* IDMAn event status register */
778 u_char idmr
; /* IDMAn event mask register */
782 /* IDMA event register bit fields
784 #define IDMA_EVENT_SC ((unsigned char)0x08) /* stop completed */
785 #define IDMA_EVENT_OB ((unsigned char)0x04) /* out of buffers */
786 #define IDMA_EVENT_EDN ((unsigned char)0x02) /* external DONE asserted */
787 #define IDMA_EVENT_BC ((unsigned char)0x01) /* buffer descriptor complete */
789 /* RISC Controller Configuration Register (RCCR) bit fields
791 #define RCCR_TIME ((uint)0x80000000) /* timer enable */
792 #define RCCR_TIMEP_MASK ((uint)0x3f000000) /* mask for timer period bit field */
793 #define RCCR_DR0M ((uint)0x00800000) /* IDMA0 request mode */
794 #define RCCR_DR1M ((uint)0x00400000) /* IDMA1 request mode */
795 #define RCCR_DR2M ((uint)0x00000080) /* IDMA2 request mode */
796 #define RCCR_DR3M ((uint)0x00000040) /* IDMA3 request mode */
797 #define RCCR_DR0QP_MASK ((uint)0x00300000) /* mask for IDMA0 req priority */
798 #define RCCR_DR0QP_HIGH ((uint)0x00000000) /* IDMA0 has high req priority */
799 #define RCCR_DR0QP_MED ((uint)0x00100000) /* IDMA0 has medium req priority */
800 #define RCCR_DR0QP_LOW ((uint)0x00200000) /* IDMA0 has low req priority */
801 #define RCCR_DR1QP_MASK ((uint)0x00030000) /* mask for IDMA1 req priority */
802 #define RCCR_DR1QP_HIGH ((uint)0x00000000) /* IDMA1 has high req priority */
803 #define RCCR_DR1QP_MED ((uint)0x00010000) /* IDMA1 has medium req priority */
804 #define RCCR_DR1QP_LOW ((uint)0x00020000) /* IDMA1 has low req priority */
805 #define RCCR_DR2QP_MASK ((uint)0x00000030) /* mask for IDMA2 req priority */
806 #define RCCR_DR2QP_HIGH ((uint)0x00000000) /* IDMA2 has high req priority */
807 #define RCCR_DR2QP_MED ((uint)0x00000010) /* IDMA2 has medium req priority */
808 #define RCCR_DR2QP_LOW ((uint)0x00000020) /* IDMA2 has low req priority */
809 #define RCCR_DR3QP_MASK ((uint)0x00000003) /* mask for IDMA3 req priority */
810 #define RCCR_DR3QP_HIGH ((uint)0x00000000) /* IDMA3 has high req priority */
811 #define RCCR_DR3QP_MED ((uint)0x00000001) /* IDMA3 has medium req priority */
812 #define RCCR_DR3QP_LOW ((uint)0x00000002) /* IDMA3 has low req priority */
813 #define RCCR_EIE ((uint)0x00080000) /* external interrupt enable */
814 #define RCCR_SCD ((uint)0x00040000) /* scheduler configuration */
815 #define RCCR_ERAM_MASK ((uint)0x0000e000) /* mask for enable RAM microcode */
816 #define RCCR_ERAM_0KB ((uint)0x00000000) /* use 0KB of dpram for microcode */
817 #define RCCR_ERAM_2KB ((uint)0x00002000) /* use 2KB of dpram for microcode */
818 #define RCCR_ERAM_4KB ((uint)0x00004000) /* use 4KB of dpram for microcode */
819 #define RCCR_ERAM_6KB ((uint)0x00006000) /* use 6KB of dpram for microcode */
820 #define RCCR_ERAM_8KB ((uint)0x00008000) /* use 8KB of dpram for microcode */
821 #define RCCR_ERAM_10KB ((uint)0x0000a000) /* use 10KB of dpram for microcode */
822 #define RCCR_ERAM_12KB ((uint)0x0000c000) /* use 12KB of dpram for microcode */
823 #define RCCR_EDM0 ((uint)0x00000800) /* DREQ0 edge detect mode */
824 #define RCCR_EDM1 ((uint)0x00000400) /* DREQ1 edge detect mode */
825 #define RCCR_EDM2 ((uint)0x00000200) /* DREQ2 edge detect mode */
826 #define RCCR_EDM3 ((uint)0x00000100) /* DREQ3 edge detect mode */
827 #define RCCR_DEM01 ((uint)0x00000008) /* DONE0/DONE1 edge detect mode */
828 #define RCCR_DEM23 ((uint)0x00000004) /* DONE2/DONE3 edge detect mode */
830 /*-----------------------------------------------------------------------
831 * CMXFCR - CMX FCC Clock Route Register
833 #define CMXFCR_FC1 0x40000000 /* FCC1 connection */
834 #define CMXFCR_RF1CS_MSK 0x38000000 /* Receive FCC1 Clock Source Mask */
835 #define CMXFCR_TF1CS_MSK 0x07000000 /* Transmit FCC1 Clock Source Mask */
836 #define CMXFCR_FC2 0x00400000 /* FCC2 connection */
837 #define CMXFCR_RF2CS_MSK 0x00380000 /* Receive FCC2 Clock Source Mask */
838 #define CMXFCR_TF2CS_MSK 0x00070000 /* Transmit FCC2 Clock Source Mask */
839 #define CMXFCR_FC3 0x00004000 /* FCC3 connection */
840 #define CMXFCR_RF3CS_MSK 0x00003800 /* Receive FCC3 Clock Source Mask */
841 #define CMXFCR_TF3CS_MSK 0x00000700 /* Transmit FCC3 Clock Source Mask */
843 #define CMXFCR_RF1CS_BRG5 0x00000000 /* Receive FCC1 Clock Source is BRG5 */
844 #define CMXFCR_RF1CS_BRG6 0x08000000 /* Receive FCC1 Clock Source is BRG6 */
845 #define CMXFCR_RF1CS_BRG7 0x10000000 /* Receive FCC1 Clock Source is BRG7 */
846 #define CMXFCR_RF1CS_BRG8 0x18000000 /* Receive FCC1 Clock Source is BRG8 */
847 #define CMXFCR_RF1CS_CLK9 0x20000000 /* Receive FCC1 Clock Source is CLK9 */
848 #define CMXFCR_RF1CS_CLK10 0x28000000 /* Receive FCC1 Clock Source is CLK10 */
849 #define CMXFCR_RF1CS_CLK11 0x30000000 /* Receive FCC1 Clock Source is CLK11 */
850 #define CMXFCR_RF1CS_CLK12 0x38000000 /* Receive FCC1 Clock Source is CLK12 */
852 #define CMXFCR_TF1CS_BRG5 0x00000000 /* Transmit FCC1 Clock Source is BRG5 */
853 #define CMXFCR_TF1CS_BRG6 0x01000000 /* Transmit FCC1 Clock Source is BRG6 */
854 #define CMXFCR_TF1CS_BRG7 0x02000000 /* Transmit FCC1 Clock Source is BRG7 */
855 #define CMXFCR_TF1CS_BRG8 0x03000000 /* Transmit FCC1 Clock Source is BRG8 */
856 #define CMXFCR_TF1CS_CLK9 0x04000000 /* Transmit FCC1 Clock Source is CLK9 */
857 #define CMXFCR_TF1CS_CLK10 0x05000000 /* Transmit FCC1 Clock Source is CLK10 */
858 #define CMXFCR_TF1CS_CLK11 0x06000000 /* Transmit FCC1 Clock Source is CLK11 */
859 #define CMXFCR_TF1CS_CLK12 0x07000000 /* Transmit FCC1 Clock Source is CLK12 */
861 #define CMXFCR_RF2CS_BRG5 0x00000000 /* Receive FCC2 Clock Source is BRG5 */
862 #define CMXFCR_RF2CS_BRG6 0x00080000 /* Receive FCC2 Clock Source is BRG6 */
863 #define CMXFCR_RF2CS_BRG7 0x00100000 /* Receive FCC2 Clock Source is BRG7 */
864 #define CMXFCR_RF2CS_BRG8 0x00180000 /* Receive FCC2 Clock Source is BRG8 */
865 #define CMXFCR_RF2CS_CLK13 0x00200000 /* Receive FCC2 Clock Source is CLK13 */
866 #define CMXFCR_RF2CS_CLK14 0x00280000 /* Receive FCC2 Clock Source is CLK14 */
867 #define CMXFCR_RF2CS_CLK15 0x00300000 /* Receive FCC2 Clock Source is CLK15 */
868 #define CMXFCR_RF2CS_CLK16 0x00380000 /* Receive FCC2 Clock Source is CLK16 */
870 #define CMXFCR_TF2CS_BRG5 0x00000000 /* Transmit FCC2 Clock Source is BRG5 */
871 #define CMXFCR_TF2CS_BRG6 0x00010000 /* Transmit FCC2 Clock Source is BRG6 */
872 #define CMXFCR_TF2CS_BRG7 0x00020000 /* Transmit FCC2 Clock Source is BRG7 */
873 #define CMXFCR_TF2CS_BRG8 0x00030000 /* Transmit FCC2 Clock Source is BRG8 */
874 #define CMXFCR_TF2CS_CLK13 0x00040000 /* Transmit FCC2 Clock Source is CLK13 */
875 #define CMXFCR_TF2CS_CLK14 0x00050000 /* Transmit FCC2 Clock Source is CLK14 */
876 #define CMXFCR_TF2CS_CLK15 0x00060000 /* Transmit FCC2 Clock Source is CLK15 */
877 #define CMXFCR_TF2CS_CLK16 0x00070000 /* Transmit FCC2 Clock Source is CLK16 */
879 #define CMXFCR_RF3CS_BRG5 0x00000000 /* Receive FCC3 Clock Source is BRG5 */
880 #define CMXFCR_RF3CS_BRG6 0x00000800 /* Receive FCC3 Clock Source is BRG6 */
881 #define CMXFCR_RF3CS_BRG7 0x00001000 /* Receive FCC3 Clock Source is BRG7 */
882 #define CMXFCR_RF3CS_BRG8 0x00001800 /* Receive FCC3 Clock Source is BRG8 */
883 #define CMXFCR_RF3CS_CLK13 0x00002000 /* Receive FCC3 Clock Source is CLK13 */
884 #define CMXFCR_RF3CS_CLK14 0x00002800 /* Receive FCC3 Clock Source is CLK14 */
885 #define CMXFCR_RF3CS_CLK15 0x00003000 /* Receive FCC3 Clock Source is CLK15 */
886 #define CMXFCR_RF3CS_CLK16 0x00003800 /* Receive FCC3 Clock Source is CLK16 */
888 #define CMXFCR_TF3CS_BRG5 0x00000000 /* Transmit FCC3 Clock Source is BRG5 */
889 #define CMXFCR_TF3CS_BRG6 0x00000100 /* Transmit FCC3 Clock Source is BRG6 */
890 #define CMXFCR_TF3CS_BRG7 0x00000200 /* Transmit FCC3 Clock Source is BRG7 */
891 #define CMXFCR_TF3CS_BRG8 0x00000300 /* Transmit FCC3 Clock Source is BRG8 */
892 #define CMXFCR_TF3CS_CLK13 0x00000400 /* Transmit FCC3 Clock Source is CLK13 */
893 #define CMXFCR_TF3CS_CLK14 0x00000500 /* Transmit FCC3 Clock Source is CLK14 */
894 #define CMXFCR_TF3CS_CLK15 0x00000600 /* Transmit FCC3 Clock Source is CLK15 */
895 #define CMXFCR_TF3CS_CLK16 0x00000700 /* Transmit FCC3 Clock Source is CLK16 */
897 /*-----------------------------------------------------------------------
898 * CMXSCR - CMX SCC Clock Route Register
900 #define CMXSCR_GR1 0x80000000 /* Grant Support of SCC1 */
901 #define CMXSCR_SC1 0x40000000 /* SCC1 connection */
902 #define CMXSCR_RS1CS_MSK 0x38000000 /* Receive SCC1 Clock Source Mask */
903 #define CMXSCR_TS1CS_MSK 0x07000000 /* Transmit SCC1 Clock Source Mask */
904 #define CMXSCR_GR2 0x00800000 /* Grant Support of SCC2 */
905 #define CMXSCR_SC2 0x00400000 /* SCC2 connection */
906 #define CMXSCR_RS2CS_MSK 0x00380000 /* Receive SCC2 Clock Source Mask */
907 #define CMXSCR_TS2CS_MSK 0x00070000 /* Transmit SCC2 Clock Source Mask */
908 #define CMXSCR_GR3 0x00008000 /* Grant Support of SCC3 */
909 #define CMXSCR_SC3 0x00004000 /* SCC3 connection */
910 #define CMXSCR_RS3CS_MSK 0x00003800 /* Receive SCC3 Clock Source Mask */
911 #define CMXSCR_TS3CS_MSK 0x00000700 /* Transmit SCC3 Clock Source Mask */
912 #define CMXSCR_GR4 0x00000080 /* Grant Support of SCC4 */
913 #define CMXSCR_SC4 0x00000040 /* SCC4 connection */
914 #define CMXSCR_RS4CS_MSK 0x00000038 /* Receive SCC4 Clock Source Mask */
915 #define CMXSCR_TS4CS_MSK 0x00000007 /* Transmit SCC4 Clock Source Mask */
917 #define CMXSCR_RS1CS_BRG1 0x00000000 /* SCC1 Rx Clock Source is BRG1 */
918 #define CMXSCR_RS1CS_BRG2 0x08000000 /* SCC1 Rx Clock Source is BRG2 */
919 #define CMXSCR_RS1CS_BRG3 0x10000000 /* SCC1 Rx Clock Source is BRG3 */
920 #define CMXSCR_RS1CS_BRG4 0x18000000 /* SCC1 Rx Clock Source is BRG4 */
921 #define CMXSCR_RS1CS_CLK11 0x20000000 /* SCC1 Rx Clock Source is CLK11 */
922 #define CMXSCR_RS1CS_CLK12 0x28000000 /* SCC1 Rx Clock Source is CLK12 */
923 #define CMXSCR_RS1CS_CLK3 0x30000000 /* SCC1 Rx Clock Source is CLK3 */
924 #define CMXSCR_RS1CS_CLK4 0x38000000 /* SCC1 Rx Clock Source is CLK4 */
926 #define CMXSCR_TS1CS_BRG1 0x00000000 /* SCC1 Tx Clock Source is BRG1 */
927 #define CMXSCR_TS1CS_BRG2 0x01000000 /* SCC1 Tx Clock Source is BRG2 */
928 #define CMXSCR_TS1CS_BRG3 0x02000000 /* SCC1 Tx Clock Source is BRG3 */
929 #define CMXSCR_TS1CS_BRG4 0x03000000 /* SCC1 Tx Clock Source is BRG4 */
930 #define CMXSCR_TS1CS_CLK11 0x04000000 /* SCC1 Tx Clock Source is CLK11 */
931 #define CMXSCR_TS1CS_CLK12 0x05000000 /* SCC1 Tx Clock Source is CLK12 */
932 #define CMXSCR_TS1CS_CLK3 0x06000000 /* SCC1 Tx Clock Source is CLK3 */
933 #define CMXSCR_TS1CS_CLK4 0x07000000 /* SCC1 Tx Clock Source is CLK4 */
935 #define CMXSCR_RS2CS_BRG1 0x00000000 /* SCC2 Rx Clock Source is BRG1 */
936 #define CMXSCR_RS2CS_BRG2 0x00080000 /* SCC2 Rx Clock Source is BRG2 */
937 #define CMXSCR_RS2CS_BRG3 0x00100000 /* SCC2 Rx Clock Source is BRG3 */
938 #define CMXSCR_RS2CS_BRG4 0x00180000 /* SCC2 Rx Clock Source is BRG4 */
939 #define CMXSCR_RS2CS_CLK11 0x00200000 /* SCC2 Rx Clock Source is CLK11 */
940 #define CMXSCR_RS2CS_CLK12 0x00280000 /* SCC2 Rx Clock Source is CLK12 */
941 #define CMXSCR_RS2CS_CLK3 0x00300000 /* SCC2 Rx Clock Source is CLK3 */
942 #define CMXSCR_RS2CS_CLK4 0x00380000 /* SCC2 Rx Clock Source is CLK4 */
944 #define CMXSCR_TS2CS_BRG1 0x00000000 /* SCC2 Tx Clock Source is BRG1 */
945 #define CMXSCR_TS2CS_BRG2 0x00010000 /* SCC2 Tx Clock Source is BRG2 */
946 #define CMXSCR_TS2CS_BRG3 0x00020000 /* SCC2 Tx Clock Source is BRG3 */
947 #define CMXSCR_TS2CS_BRG4 0x00030000 /* SCC2 Tx Clock Source is BRG4 */
948 #define CMXSCR_TS2CS_CLK11 0x00040000 /* SCC2 Tx Clock Source is CLK11 */
949 #define CMXSCR_TS2CS_CLK12 0x00050000 /* SCC2 Tx Clock Source is CLK12 */
950 #define CMXSCR_TS2CS_CLK3 0x00060000 /* SCC2 Tx Clock Source is CLK3 */
951 #define CMXSCR_TS2CS_CLK4 0x00070000 /* SCC2 Tx Clock Source is CLK4 */
953 #define CMXSCR_RS3CS_BRG1 0x00000000 /* SCC3 Rx Clock Source is BRG1 */
954 #define CMXSCR_RS3CS_BRG2 0x00000800 /* SCC3 Rx Clock Source is BRG2 */
955 #define CMXSCR_RS3CS_BRG3 0x00001000 /* SCC3 Rx Clock Source is BRG3 */
956 #define CMXSCR_RS3CS_BRG4 0x00001800 /* SCC3 Rx Clock Source is BRG4 */
957 #define CMXSCR_RS3CS_CLK5 0x00002000 /* SCC3 Rx Clock Source is CLK5 */
958 #define CMXSCR_RS3CS_CLK6 0x00002800 /* SCC3 Rx Clock Source is CLK6 */
959 #define CMXSCR_RS3CS_CLK7 0x00003000 /* SCC3 Rx Clock Source is CLK7 */
960 #define CMXSCR_RS3CS_CLK8 0x00003800 /* SCC3 Rx Clock Source is CLK8 */
962 #define CMXSCR_TS3CS_BRG1 0x00000000 /* SCC3 Tx Clock Source is BRG1 */
963 #define CMXSCR_TS3CS_BRG2 0x00000100 /* SCC3 Tx Clock Source is BRG2 */
964 #define CMXSCR_TS3CS_BRG3 0x00000200 /* SCC3 Tx Clock Source is BRG3 */
965 #define CMXSCR_TS3CS_BRG4 0x00000300 /* SCC3 Tx Clock Source is BRG4 */
966 #define CMXSCR_TS3CS_CLK5 0x00000400 /* SCC3 Tx Clock Source is CLK5 */
967 #define CMXSCR_TS3CS_CLK6 0x00000500 /* SCC3 Tx Clock Source is CLK6 */
968 #define CMXSCR_TS3CS_CLK7 0x00000600 /* SCC3 Tx Clock Source is CLK7 */
969 #define CMXSCR_TS3CS_CLK8 0x00000700 /* SCC3 Tx Clock Source is CLK8 */
971 #define CMXSCR_RS4CS_BRG1 0x00000000 /* SCC4 Rx Clock Source is BRG1 */
972 #define CMXSCR_RS4CS_BRG2 0x00000008 /* SCC4 Rx Clock Source is BRG2 */
973 #define CMXSCR_RS4CS_BRG3 0x00000010 /* SCC4 Rx Clock Source is BRG3 */
974 #define CMXSCR_RS4CS_BRG4 0x00000018 /* SCC4 Rx Clock Source is BRG4 */
975 #define CMXSCR_RS4CS_CLK5 0x00000020 /* SCC4 Rx Clock Source is CLK5 */
976 #define CMXSCR_RS4CS_CLK6 0x00000028 /* SCC4 Rx Clock Source is CLK6 */
977 #define CMXSCR_RS4CS_CLK7 0x00000030 /* SCC4 Rx Clock Source is CLK7 */
978 #define CMXSCR_RS4CS_CLK8 0x00000038 /* SCC4 Rx Clock Source is CLK8 */
980 #define CMXSCR_TS4CS_BRG1 0x00000000 /* SCC4 Tx Clock Source is BRG1 */
981 #define CMXSCR_TS4CS_BRG2 0x00000001 /* SCC4 Tx Clock Source is BRG2 */
982 #define CMXSCR_TS4CS_BRG3 0x00000002 /* SCC4 Tx Clock Source is BRG3 */
983 #define CMXSCR_TS4CS_BRG4 0x00000003 /* SCC4 Tx Clock Source is BRG4 */
984 #define CMXSCR_TS4CS_CLK5 0x00000004 /* SCC4 Tx Clock Source is CLK5 */
985 #define CMXSCR_TS4CS_CLK6 0x00000005 /* SCC4 Tx Clock Source is CLK6 */
986 #define CMXSCR_TS4CS_CLK7 0x00000006 /* SCC4 Tx Clock Source is CLK7 */
987 #define CMXSCR_TS4CS_CLK8 0x00000007 /* SCC4 Tx Clock Source is CLK8 */
989 /*-----------------------------------------------------------------------
990 * SIUMCR - SIU Module Configuration Register 4-31
992 #define SIUMCR_BBD 0x80000000 /* Bus Busy Disable */
993 #define SIUMCR_ESE 0x40000000 /* External Snoop Enable */
994 #define SIUMCR_PBSE 0x20000000 /* Parity Byte Select Enable */
995 #define SIUMCR_CDIS 0x10000000 /* Core Disable */
996 #define SIUMCR_DPPC00 0x00000000 /* Data Parity Pins Configuration*/
997 #define SIUMCR_DPPC01 0x04000000 /* - " - */
998 #define SIUMCR_DPPC10 0x08000000 /* - " - */
999 #define SIUMCR_DPPC11 0x0c000000 /* - " - */
1000 #define SIUMCR_L2CPC00 0x00000000 /* L2 Cache Pins Configuration */
1001 #define SIUMCR_L2CPC01 0x01000000 /* - " - */
1002 #define SIUMCR_L2CPC10 0x02000000 /* - " - */
1003 #define SIUMCR_L2CPC11 0x03000000 /* - " - */
1004 #define SIUMCR_LBPC00 0x00000000 /* Local Bus Pins Configuration */
1005 #define SIUMCR_LBPC01 0x00400000 /* - " - */
1006 #define SIUMCR_LBPC10 0x00800000 /* - " - */
1007 #define SIUMCR_LBPC11 0x00c00000 /* - " - */
1008 #define SIUMCR_APPC00 0x00000000 /* Address Parity Pins Configuration*/
1009 #define SIUMCR_APPC01 0x00100000 /* - " - */
1010 #define SIUMCR_APPC10 0x00200000 /* - " - */
1011 #define SIUMCR_APPC11 0x00300000 /* - " - */
1012 #define SIUMCR_CS10PC00 0x00000000 /* CS10 Pin Configuration */
1013 #define SIUMCR_CS10PC01 0x00040000 /* - " - */
1014 #define SIUMCR_CS10PC10 0x00080000 /* - " - */
1015 #define SIUMCR_CS10PC11 0x000c0000 /* - " - */
1016 #define SIUMCR_BCTLC00 0x00000000 /* Buffer Control Configuration */
1017 #define SIUMCR_BCTLC01 0x00010000 /* - " - */
1018 #define SIUMCR_BCTLC10 0x00020000 /* - " - */
1019 #define SIUMCR_BCTLC11 0x00030000 /* - " - */
1020 #define SIUMCR_MMR00 0x00000000 /* Mask Masters Requests */
1021 #define SIUMCR_MMR01 0x00004000 /* - " - */
1022 #define SIUMCR_MMR10 0x00008000 /* - " - */
1023 #define SIUMCR_MMR11 0x0000c000 /* - " - */
1024 #define SIUMCR_LPBSE 0x00002000 /* LocalBus Parity Byte Select Enable*/
1026 /*-----------------------------------------------------------------------
1027 * SCCR - System Clock Control Register 9-8
1029 #define SCCR_PCI_MODE 0x00000100 /* PCI Mode */
1030 #define SCCR_PCI_MODCK 0x00000080 /* Value of PCI_MODCK pin */
1031 #define SCCR_PCIDF_MSK 0x00000078 /* PCI division factor */
1032 #define SCCR_PCIDF_SHIFT 3
1034 #ifndef CPM_IMMR_OFFSET
1035 #define CPM_IMMR_OFFSET 0x101a8
1038 #define FCC_PSMR_RMII ((uint)0x00020000) /* Use RMII interface */
1040 /* FCC iop & clock configuration. BSP code is responsible to define Fx_RXCLK & Fx_TXCLK
1041 * in order to use clock-computing stuff below for the FCC x
1044 /* Automatically generates register configurations */
1045 #define PC_CLK(x) ((uint)(1<<(x-1))) /* FCC CLK I/O ports */
1047 #define CMXFCR_RF1CS(x) ((uint)((x-5)<<27)) /* FCC1 Receive Clock Source */
1048 #define CMXFCR_TF1CS(x) ((uint)((x-5)<<24)) /* FCC1 Transmit Clock Source */
1049 #define CMXFCR_RF2CS(x) ((uint)((x-9)<<19)) /* FCC2 Receive Clock Source */
1050 #define CMXFCR_TF2CS(x) ((uint)((x-9)<<16)) /* FCC2 Transmit Clock Source */
1051 #define CMXFCR_RF3CS(x) ((uint)((x-9)<<11)) /* FCC3 Receive Clock Source */
1052 #define CMXFCR_TF3CS(x) ((uint)((x-9)<<8)) /* FCC3 Transmit Clock Source */
1054 #define PC_F1RXCLK PC_CLK(F1_RXCLK)
1055 #define PC_F1TXCLK PC_CLK(F1_TXCLK)
1056 #define CMX1_CLK_ROUTE (CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK))
1057 #define CMX1_CLK_MASK ((uint)0xff000000)
1059 #define PC_F2RXCLK PC_CLK(F2_RXCLK)
1060 #define PC_F2TXCLK PC_CLK(F2_TXCLK)
1061 #define CMX2_CLK_ROUTE (CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK))
1062 #define CMX2_CLK_MASK ((uint)0x00ff0000)
1064 #define PC_F3RXCLK PC_CLK(F3_RXCLK)
1065 #define PC_F3TXCLK PC_CLK(F3_TXCLK)
1066 #define CMX3_CLK_ROUTE (CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK))
1067 #define CMX3_CLK_MASK ((uint)0x0000ff00)
1069 #define CPMUX_CLK_MASK (CMX3_CLK_MASK | CMX2_CLK_MASK)
1070 #define CPMUX_CLK_ROUTE (CMX3_CLK_ROUTE | CMX2_CLK_ROUTE)
1072 #define CLK_TRX (PC_F3TXCLK | PC_F3RXCLK | PC_F2TXCLK | PC_F2RXCLK)
1074 /* I/O Pin assignment for FCC1. I don't yet know the best way to do this,
1075 * but there is little variation among the choices.
1077 #define PA1_COL 0x00000001U
1078 #define PA1_CRS 0x00000002U
1079 #define PA1_TXER 0x00000004U
1080 #define PA1_TXEN 0x00000008U
1081 #define PA1_RXDV 0x00000010U
1082 #define PA1_RXER 0x00000020U
1083 #define PA1_TXDAT 0x00003c00U
1084 #define PA1_RXDAT 0x0003c000U
1085 #define PA1_PSORA0 (PA1_RXDAT | PA1_TXDAT)
1086 #define PA1_PSORA1 (PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \
1087 PA1_RXDV | PA1_RXER)
1088 #define PA1_DIRA0 (PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV)
1089 #define PA1_DIRA1 (PA1_TXDAT | PA1_TXEN | PA1_TXER)
1092 /* I/O Pin assignment for FCC2. I don't yet know the best way to do this,
1093 * but there is little variation among the choices.
1095 #define PB2_TXER 0x00000001U
1096 #define PB2_RXDV 0x00000002U
1097 #define PB2_TXEN 0x00000004U
1098 #define PB2_RXER 0x00000008U
1099 #define PB2_COL 0x00000010U
1100 #define PB2_CRS 0x00000020U
1101 #define PB2_TXDAT 0x000003c0U
1102 #define PB2_RXDAT 0x00003c00U
1103 #define PB2_PSORB0 (PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \
1104 PB2_RXER | PB2_RXDV | PB2_TXER)
1105 #define PB2_PSORB1 (PB2_TXEN)
1106 #define PB2_DIRB0 (PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV)
1107 #define PB2_DIRB1 (PB2_TXDAT | PB2_TXEN | PB2_TXER)
1110 /* I/O Pin assignment for FCC3. I don't yet know the best way to do this,
1111 * but there is little variation among the choices.
1113 #define PB3_RXDV 0x00004000U
1114 #define PB3_RXER 0x00008000U
1115 #define PB3_TXER 0x00010000U
1116 #define PB3_TXEN 0x00020000U
1117 #define PB3_COL 0x00040000U
1118 #define PB3_CRS 0x00080000U
1119 #define PB3_TXDAT 0x0f000000U
1120 #define PC3_TXDAT 0x00000010U
1121 #define PB3_RXDAT 0x00f00000U
1122 #define PB3_PSORB0 (PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \
1123 PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN)
1124 #define PB3_PSORB1 0
1125 #define PB3_DIRB0 (PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV)
1126 #define PB3_DIRB1 (PB3_TXDAT | PB3_TXEN | PB3_TXER)
1127 #define PC3_DIRC1 (PC3_TXDAT)
1129 /* Handy macro to specify mem for FCCs*/
1130 #define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
1131 #define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
1132 #define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
1133 #define FCC3_MEM_OFFSET FCC_MEM_OFFSET(2)
1135 /* Clocks and GRG's */
1143 enum cpm_clk_target
{
1157 CPM_BRG1
, /* Baud Rate Generator 1 */
1158 CPM_BRG2
, /* Baud Rate Generator 2 */
1159 CPM_BRG3
, /* Baud Rate Generator 3 */
1160 CPM_BRG4
, /* Baud Rate Generator 4 */
1161 CPM_BRG5
, /* Baud Rate Generator 5 */
1162 CPM_BRG6
, /* Baud Rate Generator 6 */
1163 CPM_BRG7
, /* Baud Rate Generator 7 */
1164 CPM_BRG8
, /* Baud Rate Generator 8 */
1165 CPM_CLK1
, /* Clock 1 */
1166 CPM_CLK2
, /* Clock 2 */
1167 CPM_CLK3
, /* Clock 3 */
1168 CPM_CLK4
, /* Clock 4 */
1169 CPM_CLK5
, /* Clock 5 */
1170 CPM_CLK6
, /* Clock 6 */
1171 CPM_CLK7
, /* Clock 7 */
1172 CPM_CLK8
, /* Clock 8 */
1173 CPM_CLK9
, /* Clock 9 */
1174 CPM_CLK10
, /* Clock 10 */
1175 CPM_CLK11
, /* Clock 11 */
1176 CPM_CLK12
, /* Clock 12 */
1177 CPM_CLK13
, /* Clock 13 */
1178 CPM_CLK14
, /* Clock 14 */
1179 CPM_CLK15
, /* Clock 15 */
1180 CPM_CLK16
, /* Clock 16 */
1181 CPM_CLK17
, /* Clock 17 */
1182 CPM_CLK18
, /* Clock 18 */
1183 CPM_CLK19
, /* Clock 19 */
1184 CPM_CLK20
, /* Clock 20 */
1188 extern int cpm2_clk_setup(enum cpm_clk_target target
, int clock
, int mode
);
1189 extern int cpm2_smc_clk_setup(enum cpm_clk_target target
, int clock
);
1191 #define CPM_PIN_INPUT 0
1192 #define CPM_PIN_OUTPUT 1
1193 #define CPM_PIN_PRIMARY 0
1194 #define CPM_PIN_SECONDARY 2
1195 #define CPM_PIN_GPIO 4
1196 #define CPM_PIN_OPENDRAIN 8
1198 void cpm2_set_pin(int port
, int pin
, int flags
);
1200 #endif /* __CPM2__ */
1201 #endif /* __KERNEL__ */