drivers/scsi/qlogicpti.h

   1 /* qlogicpti.h: Performance Technologies QlogicISP sbus card defines.
   2  *
   3  * Copyright (C) 1996 David S. Miller (davem@caipfs.rutgers.edu)
   4  */
   5
   6 #ifndef _QLOGICPTI_H
   7 #define _QLOGICPTI_H
   8
   9 /* Qlogic/SBUS controller registers. */
  10 #define SBUS_CFG1       0x006UL
  11 #define SBUS_CTRL       0x008UL
  12 #define SBUS_STAT       0x00aUL
  13 #define SBUS_SEMAPHORE  0x00cUL
  14 #define CMD_DMA_CTRL    0x022UL
  15 #define DATA_DMA_CTRL   0x042UL
  16 #define MBOX0           0x080UL
  17 #define MBOX1           0x082UL
  18 #define MBOX2           0x084UL
  19 #define MBOX3           0x086UL
  20 #define MBOX4           0x088UL
  21 #define MBOX5           0x08aUL
  22 #define CPU_CMD         0x214UL
  23 #define CPU_ORIDE       0x224UL
  24 #define CPU_PCTRL       0x272UL
  25 #define CPU_PDIFF       0x276UL
  26 #define RISC_PSR        0x420UL
  27 #define RISC_MTREG      0x42EUL
  28 #define HCCTRL          0x440UL
  29
  30 /* SCSI parameters for this driver. */
  31 #define MAX_TARGETS     16
  32 #define MAX_LUNS        8
  33
  34 /* With the qlogic interface, every queue slot can hold a SCSI
  35  * command with up to 4 scatter/gather entries.  If we need more
  36  * than 4 entries, continuation entries can be used that hold
  37  * another 7 entries each.  Unlike for other drivers, this means
  38  * that the maximum number of scatter/gather entries we can
  39  * support at any given time is a function of the number of queue
  40  * slots available.  That is, host->can_queue and host->sg_tablesize
  41  * are dynamic and _not_ independent.  This all works fine because
  42  * requests are queued serially and the scatter/gather limit is
  43  * determined for each queue request anew.
  44  */
  45 #define QLOGICPTI_REQ_QUEUE_LEN 255     /* must be power of two - 1 */
  46 #define QLOGICPTI_MAX_SG(ql)    (4 + ((ql) > 0) ? 7*((ql) - 1) : 0)
  47
  48 /* mailbox command complete status codes */
  49 #define MBOX_COMMAND_COMPLETE           0x4000
  50 #define INVALID_COMMAND                 0x4001
  51 #define HOST_INTERFACE_ERROR            0x4002
  52 #define TEST_FAILED                     0x4003
  53 #define COMMAND_ERROR                   0x4005
  54 #define COMMAND_PARAM_ERROR             0x4006
  55
  56 /* async event status codes */
  57 #define ASYNC_SCSI_BUS_RESET            0x8001
  58 #define SYSTEM_ERROR                    0x8002
  59 #define REQUEST_TRANSFER_ERROR          0x8003
  60 #define RESPONSE_TRANSFER_ERROR         0x8004
  61 #define REQUEST_QUEUE_WAKEUP            0x8005
  62 #define EXECUTION_TIMEOUT_RESET         0x8006
  63
  64 /* Am I fucking pedantic or what? */
  65 struct Entry_header {
  66 #ifdef __BIG_ENDIAN
  67         u8      entry_cnt;
  68         u8      entry_type;
  69         u8      flags;
  70         u8      sys_def_1;
  71 #else /* __LITTLE_ENDIAN */
  72         u8      entry_type;
  73         u8      entry_cnt;
  74         u8      sys_def_1;
  75         u8      flags;
  76 #endif
  77 };
  78
  79 /* entry header type commands */
  80 #define ENTRY_COMMAND           1
  81 #define ENTRY_CONTINUATION      2
  82 #define ENTRY_STATUS            3
  83 #define ENTRY_MARKER            4
  84 #define ENTRY_EXTENDED_COMMAND  5
  85
  86 /* entry header flag definitions */
  87 #define EFLAG_CONTINUATION      1
  88 #define EFLAG_BUSY              2
  89 #define EFLAG_BAD_HEADER        4
  90 #define EFLAG_BAD_PAYLOAD       8
  91
  92 struct dataseg {
  93         u32     d_base;
  94         u32     d_count;
  95 };
  96
  97 struct Command_Entry {
  98         struct Entry_header     hdr;
  99         u32                     handle;
 100 #ifdef __BIG_ENDIAN
 101         u8                      target_id;
 102         u8                      target_lun;
 103 #else /* __LITTLE_ENDIAN */
 104         u8                      target_lun;
 105         u8                      target_id;
 106 #endif
 107         u16                     cdb_length;
 108         u16                     control_flags;
 109         u16                     rsvd;
 110         u16                     time_out;
 111         u16                     segment_cnt;
 112         u8                      cdb[12];
 113         struct dataseg          dataseg[4];
 114 };
 115
 116 /* command entry control flag definitions */
 117 #define CFLAG_NODISC            0x01
 118 #define CFLAG_HEAD_TAG          0x02
 119 #define CFLAG_ORDERED_TAG       0x04
 120 #define CFLAG_SIMPLE_TAG        0x08
 121 #define CFLAG_TAR_RTN           0x10
 122 #define CFLAG_READ              0x20
 123 #define CFLAG_WRITE             0x40
 124
 125 struct Ext_Command_Entry {
 126         struct Entry_header     hdr;
 127         u32                     handle;
 128 #ifdef __BIG_ENDIAN
 129         u8                      target_id;
 130         u8                      target_lun;
 131 #else /* __LITTLE_ENDIAN */
 132         u8                      target_lun;
 133         u8                      target_id;
 134 #endif
 135         u16                     cdb_length;
 136         u16                     control_flags;
 137         u16                     rsvd;
 138         u16                     time_out;
 139         u16                     segment_cnt;
 140         u8                      cdb[44];
 141 };
 142
 143 struct Continuation_Entry {
 144         struct Entry_header     hdr;
 145         u32                     reserved;
 146         struct dataseg          dataseg[7];
 147 };
 148
 149 struct Marker_Entry {
 150         struct Entry_header     hdr;
 151         u32                     reserved;
 152 #ifdef __BIG_ENDIAN
 153         u8                      target_id;
 154         u8                      target_lun;
 155 #else /* __LITTLE_ENDIAN */
 156         u8                      target_lun;
 157         u8                      target_id;
 158 #endif
 159 #ifdef __BIG_ENDIAN
 160         u8                      rsvd;
 161         u8                      modifier;
 162 #else /* __LITTLE_ENDIAN */
 163         u8                      modifier;
 164         u8                      rsvd;
 165 #endif
 166         u8                      rsvds[52];
 167 };
 168
 169 /* marker entry modifier definitions */
 170 #define SYNC_DEVICE     0
 171 #define SYNC_TARGET     1
 172 #define SYNC_ALL        2
 173
 174 struct Status_Entry {
 175         struct Entry_header     hdr;
 176         u32                     handle;
 177         u16                     scsi_status;
 178         u16                     completion_status;
 179         u16                     state_flags;
 180         u16                     status_flags;
 181         u16                     time;
 182         u16                     req_sense_len;
 183         u32                     residual;
 184         u8                      rsvd[8];
 185         u8                      req_sense_data[32];
 186 };
 187
 188 /* status entry completion status definitions */
 189 #define CS_COMPLETE                     0x0000
 190 #define CS_INCOMPLETE                   0x0001
 191 #define CS_DMA_ERROR                    0x0002
 192 #define CS_TRANSPORT_ERROR              0x0003
 193 #define CS_RESET_OCCURRED               0x0004
 194 #define CS_ABORTED                      0x0005
 195 #define CS_TIMEOUT                      0x0006
 196 #define CS_DATA_OVERRUN                 0x0007
 197 #define CS_COMMAND_OVERRUN              0x0008
 198 #define CS_STATUS_OVERRUN               0x0009
 199 #define CS_BAD_MESSAGE                  0x000a
 200 #define CS_NO_MESSAGE_OUT               0x000b
 201 #define CS_EXT_ID_FAILED                0x000c
 202 #define CS_IDE_MSG_FAILED               0x000d
 203 #define CS_ABORT_MSG_FAILED             0x000e
 204 #define CS_REJECT_MSG_FAILED            0x000f
 205 #define CS_NOP_MSG_FAILED               0x0010
 206 #define CS_PARITY_ERROR_MSG_FAILED      0x0011
 207 #define CS_DEVICE_RESET_MSG_FAILED      0x0012
 208 #define CS_ID_MSG_FAILED                0x0013
 209 #define CS_UNEXP_BUS_FREE               0x0014
 210 #define CS_DATA_UNDERRUN                0x0015
 211 #define CS_BUS_RESET                    0x001c
 212
 213 /* status entry state flag definitions */
 214 #define SF_GOT_BUS                      0x0100
 215 #define SF_GOT_TARGET                   0x0200
 216 #define SF_SENT_CDB                     0x0400
 217 #define SF_TRANSFERRED_DATA             0x0800
 218 #define SF_GOT_STATUS                   0x1000
 219 #define SF_GOT_SENSE                    0x2000
 220
 221 /* status entry status flag definitions */
 222 #define STF_DISCONNECT                  0x0001
 223 #define STF_SYNCHRONOUS                 0x0002
 224 #define STF_PARITY_ERROR                0x0004
 225 #define STF_BUS_RESET                   0x0008
 226 #define STF_DEVICE_RESET                0x0010
 227 #define STF_ABORTED                     0x0020
 228 #define STF_TIMEOUT                     0x0040
 229 #define STF_NEGOTIATION                 0x0080
 230
 231 /* mailbox commands */
 232 #define MBOX_NO_OP                      0x0000
 233 #define MBOX_LOAD_RAM                   0x0001
 234 #define MBOX_EXEC_FIRMWARE              0x0002
 235 #define MBOX_DUMP_RAM                   0x0003
 236 #define MBOX_WRITE_RAM_WORD             0x0004
 237 #define MBOX_READ_RAM_WORD              0x0005
 238 #define MBOX_MAILBOX_REG_TEST           0x0006
 239 #define MBOX_VERIFY_CHECKSUM            0x0007
 240 #define MBOX_ABOUT_FIRMWARE             0x0008
 241 #define MBOX_CHECK_FIRMWARE             0x000e
 242 #define MBOX_INIT_REQ_QUEUE             0x0010
 243 #define MBOX_INIT_RES_QUEUE             0x0011
 244 #define MBOX_EXECUTE_IOCB               0x0012
 245 #define MBOX_WAKE_UP                    0x0013
 246 #define MBOX_STOP_FIRMWARE              0x0014
 247 #define MBOX_ABORT                      0x0015
 248 #define MBOX_ABORT_DEVICE               0x0016
 249 #define MBOX_ABORT_TARGET               0x0017
 250 #define MBOX_BUS_RESET                  0x0018
 251 #define MBOX_STOP_QUEUE                 0x0019
 252 #define MBOX_START_QUEUE                0x001a
 253 #define MBOX_SINGLE_STEP_QUEUE          0x001b
 254 #define MBOX_ABORT_QUEUE                0x001c
 255 #define MBOX_GET_DEV_QUEUE_STATUS       0x001d
 256 #define MBOX_GET_FIRMWARE_STATUS        0x001f
 257 #define MBOX_GET_INIT_SCSI_ID           0x0020
 258 #define MBOX_GET_SELECT_TIMEOUT         0x0021
 259 #define MBOX_GET_RETRY_COUNT            0x0022
 260 #define MBOX_GET_TAG_AGE_LIMIT          0x0023
 261 #define MBOX_GET_CLOCK_RATE             0x0024
 262 #define MBOX_GET_ACT_NEG_STATE          0x0025
 263 #define MBOX_GET_ASYNC_DATA_SETUP_TIME  0x0026
 264 #define MBOX_GET_SBUS_PARAMS            0x0027
 265 #define MBOX_GET_TARGET_PARAMS          0x0028
 266 #define MBOX_GET_DEV_QUEUE_PARAMS       0x0029
 267 #define MBOX_SET_INIT_SCSI_ID           0x0030
 268 #define MBOX_SET_SELECT_TIMEOUT         0x0031
 269 #define MBOX_SET_RETRY_COUNT            0x0032
 270 #define MBOX_SET_TAG_AGE_LIMIT          0x0033
 271 #define MBOX_SET_CLOCK_RATE             0x0034
 272 #define MBOX_SET_ACTIVE_NEG_STATE       0x0035
 273 #define MBOX_SET_ASYNC_DATA_SETUP_TIME  0x0036
 274 #define MBOX_SET_SBUS_CONTROL_PARAMS    0x0037
 275 #define MBOX_SET_TARGET_PARAMS          0x0038
 276 #define MBOX_SET_DEV_QUEUE_PARAMS       0x0039
 277
 278 struct host_param {
 279         u_short         initiator_scsi_id;
 280         u_short         bus_reset_delay;
 281         u_short         retry_count;
 282         u_short         retry_delay;
 283         u_short         async_data_setup_time;
 284         u_short         req_ack_active_negation;
 285         u_short         data_line_active_negation;
 286         u_short         data_dma_burst_enable;
 287         u_short         command_dma_burst_enable;
 288         u_short         tag_aging;
 289         u_short         selection_timeout;
 290         u_short         max_queue_depth;
 291 };
 292
 293 /*
 294  * Device Flags:
 295  *
 296  * Bit  Name
 297  * ---------
 298  *  7   Disconnect Privilege
 299  *  6   Parity Checking
 300  *  5   Wide Data Transfers
 301  *  4   Synchronous Data Transfers
 302  *  3   Tagged Queuing
 303  *  2   Automatic Request Sense
 304  *  1   Stop Queue on Check Condition
 305  *  0   Renegotiate on Error
 306  */
 307
 308 struct dev_param {
 309         u_short         device_flags;
 310         u_short         execution_throttle;
 311         u_short         synchronous_period;
 312         u_short         synchronous_offset;
 313         u_short         device_enable;
 314         u_short         reserved; /* pad */
 315 };
 316
 317 /*
 318  * The result queue can be quite a bit smaller since continuation entries
 319  * do not show up there:
 320  */
 321 #define RES_QUEUE_LEN           255     /* Must be power of two - 1 */
 322 #define QUEUE_ENTRY_LEN         64
 323
 324 #define NEXT_REQ_PTR(wheee)   (((wheee) + 1) & QLOGICPTI_REQ_QUEUE_LEN)
 325 #define NEXT_RES_PTR(wheee)   (((wheee) + 1) & RES_QUEUE_LEN)
 326 #define PREV_REQ_PTR(wheee)   (((wheee) - 1) & QLOGICPTI_REQ_QUEUE_LEN)
 327 #define PREV_RES_PTR(wheee)   (((wheee) - 1) & RES_QUEUE_LEN)
 328
 329 struct pti_queue_entry {
 330         char __opaque[QUEUE_ENTRY_LEN];
 331 };
 332
 333 struct scsi_cmnd;
 334
 335 /* Software state for the driver. */
 336 struct qlogicpti {
 337         /* These are the hot elements in the cache, so they come first. */
 338         void __iomem             *qregs;                /* Adapter registers          */
 339         struct pti_queue_entry   *res_cpu;              /* Ptr to RESPONSE bufs (CPU) */
 340         struct pti_queue_entry   *req_cpu;              /* Ptr to REQUEST bufs (CPU)  */
 341
 342         u_int                     req_in_ptr;           /* index of next request slot */
 343         u_int                     res_out_ptr;          /* index of next result slot  */
 344         long                      send_marker;          /* must we send a marker?     */
 345         struct sbus_dev          *sdev;
 346         unsigned long             __pad;
 347
 348         int                       cmd_count[MAX_TARGETS];
 349         unsigned long             tag_ages[MAX_TARGETS];
 350
 351         /* The cmd->handler is only 32-bits, so that things work even on monster
 352          * Ex000 sparc64 machines with >4GB of ram we just keep track of the
 353          * scsi command pointers here.  This is essentially what Matt Jacob does. -DaveM
 354          */
 355         struct scsi_cmnd         *cmd_slots[QLOGICPTI_REQ_QUEUE_LEN + 1];
 356
 357         /* The rest of the elements are unimportant for performance. */
 358         struct qlogicpti         *next;
 359         __u32                     res_dvma;             /* Ptr to RESPONSE bufs (DVMA)*/
 360         __u32                     req_dvma;             /* Ptr to REQUEST bufs (DVMA) */
 361         u_char                    fware_majrev, fware_minrev, fware_micrev;
 362         struct Scsi_Host         *qhost;
 363         int                       qpti_id;
 364         int                       scsi_id;
 365         int                       prom_node;
 366         char                      prom_name[64];
 367         int                       irq;
 368         char                      differential, ultra, clock;
 369         unsigned char             bursts;
 370         struct  host_param        host_param;
 371         struct  dev_param         dev_param[MAX_TARGETS];
 372
 373         void __iomem              *sreg;
 374 #define SREG_TPOWER               0x80   /* State of termpwr           */
 375 #define SREG_FUSE                 0x40   /* State of on board fuse     */
 376 #define SREG_PDISAB               0x20   /* Disable state for power on */
 377 #define SREG_DSENSE               0x10   /* Sense for differential     */
 378 #define SREG_IMASK                0x0c   /* Interrupt level            */
 379 #define SREG_SPMASK               0x03   /* Mask for switch pack       */
 380         unsigned char             swsreg;
 381         unsigned int
 382                 gotirq  :       1,      /* this instance got an irq */
 383                 is_pti  :       1,      /* Non-zero if this is a PTI board. */
 384                 sbits   :       16;     /* syncmode known bits */
 385 };
 386
 387 /* How to twiddle them bits... */
 388
 389 /* SBUS config register one. */
 390 #define SBUS_CFG1_EPAR          0x0100      /* Enable parity checking           */
 391 #define SBUS_CFG1_FMASK         0x00f0      /* Forth code cycle mask            */
 392 #define SBUS_CFG1_BENAB         0x0004      /* Burst dvma enable                */
 393 #define SBUS_CFG1_B64           0x0003      /* Enable 64byte bursts             */
 394 #define SBUS_CFG1_B32           0x0002      /* Enable 32byte bursts             */
 395 #define SBUS_CFG1_B16           0x0001      /* Enable 16byte bursts             */
 396 #define SBUS_CFG1_B8            0x0008      /* Enable 8byte bursts              */
 397
 398 /* SBUS control register */
 399 #define SBUS_CTRL_EDIRQ         0x0020      /* Enable Data DVMA Interrupts      */
 400 #define SBUS_CTRL_ECIRQ         0x0010      /* Enable Command DVMA Interrupts   */
 401 #define SBUS_CTRL_ESIRQ         0x0008      /* Enable SCSI Processor Interrupts */
 402 #define SBUS_CTRL_ERIRQ         0x0004      /* Enable RISC Processor Interrupts */
 403 #define SBUS_CTRL_GENAB         0x0002      /* Global Interrupt Enable          */
 404 #define SBUS_CTRL_RESET         0x0001      /* Soft Reset                       */
 405
 406 /* SBUS status register */
 407 #define SBUS_STAT_DINT          0x0020      /* Data DVMA IRQ pending            */
 408 #define SBUS_STAT_CINT          0x0010      /* Command DVMA IRQ pending         */
 409 #define SBUS_STAT_SINT          0x0008      /* SCSI Processor IRQ pending       */
 410 #define SBUS_STAT_RINT          0x0004      /* RISC Processor IRQ pending       */
 411 #define SBUS_STAT_GINT          0x0002      /* Global IRQ pending               */
 412
 413 /* SBUS semaphore register */
 414 #define SBUS_SEMAPHORE_STAT     0x0002      /* Semaphore status bit             */
 415 #define SBUS_SEMAPHORE_LCK      0x0001      /* Semaphore lock bit               */
 416
 417 /* DVMA control register */
 418 #define DMA_CTRL_CSUSPEND       0x0010      /* DMA channel suspend              */
 419 #define DMA_CTRL_CCLEAR         0x0008      /* DMA channel clear and reset      */
 420 #define DMA_CTRL_FCLEAR         0x0004      /* DMA fifo clear                   */
 421 #define DMA_CTRL_CIRQ           0x0002      /* DMA irq clear                    */
 422 #define DMA_CTRL_DMASTART       0x0001      /* DMA transfer start               */
 423
 424 /* SCSI processor override register */
 425 #define CPU_ORIDE_ETRIG         0x8000      /* External trigger enable          */
 426 #define CPU_ORIDE_STEP          0x4000      /* Single step mode enable          */
 427 #define CPU_ORIDE_BKPT          0x2000      /* Breakpoint reg enable            */
 428 #define CPU_ORIDE_PWRITE        0x1000      /* SCSI pin write enable            */
 429 #define CPU_ORIDE_OFORCE        0x0800      /* Force outputs on                 */
 430 #define CPU_ORIDE_LBACK         0x0400      /* SCSI loopback enable             */
 431 #define CPU_ORIDE_PTEST         0x0200      /* Parity test enable               */
 432 #define CPU_ORIDE_TENAB         0x0100      /* SCSI pins tristate enable        */
 433 #define CPU_ORIDE_TPINS         0x0080      /* SCSI pins enable                 */
 434 #define CPU_ORIDE_FRESET        0x0008      /* FIFO reset                       */
 435 #define CPU_ORIDE_CTERM         0x0004      /* Command terminate                */
 436 #define CPU_ORIDE_RREG          0x0002      /* Reset SCSI processor regs        */
 437 #define CPU_ORIDE_RMOD          0x0001      /* Reset SCSI processor module      */
 438
 439 /* SCSI processor commands */
 440 #define CPU_CMD_BRESET          0x300b      /* Reset SCSI bus                   */
 441
 442 /* SCSI processor pin control register */
 443 #define CPU_PCTRL_PVALID        0x8000      /* Phase bits are valid             */
 444 #define CPU_PCTRL_PHI           0x0400      /* Parity bit high                  */
 445 #define CPU_PCTRL_PLO           0x0200      /* Parity bit low                   */
 446 #define CPU_PCTRL_REQ           0x0100      /* REQ bus signal                   */
 447 #define CPU_PCTRL_ACK           0x0080      /* ACK bus signal                   */
 448 #define CPU_PCTRL_RST           0x0040      /* RST bus signal                   */
 449 #define CPU_PCTRL_BSY           0x0020      /* BSY bus signal                   */
 450 #define CPU_PCTRL_SEL           0x0010      /* SEL bus signal                   */
 451 #define CPU_PCTRL_ATN           0x0008      /* ATN bus signal                   */
 452 #define CPU_PCTRL_MSG           0x0004      /* MSG bus signal                   */
 453 #define CPU_PCTRL_CD            0x0002      /* CD bus signal                    */
 454 #define CPU_PCTRL_IO            0x0001      /* IO bus signal                    */
 455
 456 /* SCSI processor differential pins register */
 457 #define CPU_PDIFF_SENSE         0x0200      /* Differential sense               */
 458 #define CPU_PDIFF_MODE          0x0100      /* Differential mode                */
 459 #define CPU_PDIFF_OENAB         0x0080      /* Outputs enable                   */
 460 #define CPU_PDIFF_PMASK         0x007c      /* Differential control pins        */
 461 #define CPU_PDIFF_TGT           0x0002      /* Target mode enable               */
 462 #define CPU_PDIFF_INIT          0x0001      /* Initiator mode enable            */
 463
 464 /* RISC processor status register */
 465 #define RISC_PSR_FTRUE          0x8000      /* Force true                       */
 466 #define RISC_PSR_LCD            0x4000      /* Loop counter shows done status   */
 467 #define RISC_PSR_RIRQ           0x2000      /* RISC irq status                  */
 468 #define RISC_PSR_TOFLOW         0x1000      /* Timer overflow (rollover)        */
 469 #define RISC_PSR_AOFLOW         0x0800      /* Arithmetic overflow              */
 470 #define RISC_PSR_AMSB           0x0400      /* Arithmetic big endian            */
 471 #define RISC_PSR_ACARRY         0x0200      /* Arithmetic carry                 */
 472 #define RISC_PSR_AZERO          0x0100      /* Arithmetic zero                  */
 473 #define RISC_PSR_ULTRA          0x0020      /* Ultra mode                       */
 474 #define RISC_PSR_DIRQ           0x0010      /* DVMA interrupt                   */
 475 #define RISC_PSR_SIRQ           0x0008      /* SCSI processor interrupt         */
 476 #define RISC_PSR_HIRQ           0x0004      /* Host interrupt                   */
 477 #define RISC_PSR_IPEND          0x0002      /* Interrupt pending                */
 478 #define RISC_PSR_FFALSE         0x0001      /* Force false                      */
 479
 480 /* RISC processor memory timing register */
 481 #define RISC_MTREG_P1DFLT       0x1200      /* Default read/write timing, pg1   */
 482 #define RISC_MTREG_P0DFLT       0x0012      /* Default read/write timing, pg0   */
 483 #define RISC_MTREG_P1ULTRA      0x2300      /* Ultra-mode rw timing, pg1        */
 484 #define RISC_MTREG_P0ULTRA      0x0023      /* Ultra-mode rw timing, pg0        */
 485
 486 /* Host command/ctrl register */
 487 #define HCCTRL_NOP              0x0000      /* CMD: No operation                */
 488 #define HCCTRL_RESET            0x1000      /* CMD: Reset RISC cpu              */
 489 #define HCCTRL_PAUSE            0x2000      /* CMD: Pause RISC cpu              */
 490 #define HCCTRL_REL              0x3000      /* CMD: Release paused RISC cpu     */
 491 #define HCCTRL_STEP             0x4000      /* CMD: Single step RISC cpu        */
 492 #define HCCTRL_SHIRQ            0x5000      /* CMD: Set host irq                */
 493 #define HCCTRL_CHIRQ            0x6000      /* CMD: Clear host irq              */
 494 #define HCCTRL_CRIRQ            0x7000      /* CMD: Clear RISC cpu irq          */
 495 #define HCCTRL_BKPT             0x8000      /* CMD: Breakpoint enables change   */
 496 #define HCCTRL_TMODE            0xf000      /* CMD: Enable test mode            */
 497 #define HCCTRL_HIRQ             0x0080      /* Host IRQ pending                 */
 498 #define HCCTRL_RRIP             0x0040      /* RISC cpu reset in happening now  */
 499 #define HCCTRL_RPAUSED          0x0020      /* RISC cpu is paused now           */
 500 #define HCCTRL_EBENAB           0x0010      /* External breakpoint enable       */
 501 #define HCCTRL_B1ENAB           0x0008      /* Breakpoint 1 enable              */
 502 #define HCCTRL_B0ENAB           0x0004      /* Breakpoint 0 enable              */
 503
 504 /* For our interrupt engine. */
 505 #define for_each_qlogicpti(qp) \
 506         for((qp) = qptichain; (qp); (qp) = (qp)->next)
 507
 508 #endif /* !(_QLOGICPTI_H) */