2 * Copyright (c) 1996 John Shifflett, GeoLog Consulting
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2, or (at your option)
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
18 * Drew Eckhardt's excellent 'Generic NCR5380' sources from Linux-PC
19 * provided much of the inspiration and some of the code for this
20 * driver. Everything I know about Amiga DMA was gleaned from careful
21 * reading of Hamish Mcdonald's original wd33c93 driver; in fact, I
22 * borrowed shamelessly from all over that source. Thanks Hamish!
24 * _This_ driver is (I feel) an improvement over the old one in
27 * - Target Disconnection/Reconnection is now supported. Any
28 * system with more than one device active on the SCSI bus
29 * will benefit from this. The driver defaults to what I
30 * call 'adaptive disconnect' - meaning that each command
31 * is evaluated individually as to whether or not it should
32 * be run with the option to disconnect/reselect (if the
33 * device chooses), or as a "SCSI-bus-hog".
35 * - Synchronous data transfers are now supported. Because of
36 * a few devices that choke after telling the driver that
37 * they can do sync transfers, we don't automatically use
38 * this faster protocol - it can be enabled via the command-
39 * line on a device-by-device basis.
41 * - Runtime operating parameters can now be specified through
42 * the 'amiboot' or the 'insmod' command line. For amiboot do:
43 * "amiboot [usual stuff] wd33c93=blah,blah,blah"
44 * The defaults should be good for most people. See the comment
45 * for 'setup_strings' below for more details.
47 * - The old driver relied exclusively on what the Western Digital
48 * docs call "Combination Level 2 Commands", which are a great
49 * idea in that the CPU is relieved of a lot of interrupt
50 * overhead. However, by accepting a certain (user-settable)
51 * amount of additional interrupts, this driver achieves
52 * better control over the SCSI bus, and data transfers are
53 * almost as fast while being much easier to define, track,
58 * more speed. linked commands.
61 * People with bug reports, wish-lists, complaints, comments,
62 * or improvements are asked to pah-leeez email me (John Shifflett)
63 * at john@geolog.com or jshiffle@netcom.com! I'm anxious to get
64 * this thing into as good a shape as possible, and I'm positive
65 * there are lots of lurking bugs and "Stupid Places".
69 * Added support for pre -A chips, which don't have advanced features
70 * and will generate CSR_RESEL rather than CSR_RESEL_AM.
71 * Richard Hirst <richard@sleepie.demon.co.uk> August 2000
74 #include <linux/module.h>
76 #include <linux/string.h>
77 #include <linux/delay.h>
78 #include <linux/init.h>
79 #include <linux/interrupt.h>
80 #include <linux/blkdev.h>
82 #include <scsi/scsi.h>
83 #include <scsi/scsi_cmnd.h>
84 #include <scsi/scsi_device.h>
85 #include <scsi/scsi_host.h>
90 #define WD33C93_VERSION "1.26"
91 #define WD33C93_DATE "22/Feb/2003"
93 MODULE_AUTHOR("John Shifflett");
94 MODULE_DESCRIPTION("Generic WD33C93 SCSI driver");
95 MODULE_LICENSE("GPL");
98 * 'setup_strings' is a single string used to pass operating parameters and
99 * settings from the kernel/module command-line to the driver. 'setup_args[]'
100 * is an array of strings that define the compile-time default values for
101 * these settings. If Linux boots with an amiboot or insmod command-line,
102 * those settings are combined with 'setup_args[]'. Note that amiboot
103 * command-lines are prefixed with "wd33c93=" while insmod uses a
104 * "setup_strings=" prefix. The driver recognizes the following keywords
105 * (lower case required) and arguments:
107 * - nosync:bitmask -bitmask is a byte where the 1st 7 bits correspond with
108 * the 7 possible SCSI devices. Set a bit to negotiate for
109 * asynchronous transfers on that device. To maintain
110 * backwards compatibility, a command-line such as
111 * "wd33c93=255" will be automatically translated to
112 * "wd33c93=nosync:0xff".
113 * - nodma:x -x = 1 to disable DMA, x = 0 to enable it. Argument is
114 * optional - if not present, same as "nodma:1".
115 * - period:ns -ns is the minimum # of nanoseconds in a SCSI data transfer
116 * period. Default is 500; acceptable values are 250 - 1000.
117 * - disconnect:x -x = 0 to never allow disconnects, 2 to always allow them.
118 * x = 1 does 'adaptive' disconnects, which is the default
119 * and generally the best choice.
120 * - debug:x -If 'DEBUGGING_ON' is defined, x is a bit mask that causes
121 * various types of debug output to printed - see the DB_xxx
122 * defines in wd33c93.h
123 * - clock:x -x = clock input in MHz for WD33c93 chip. Normal values
124 * would be from 8 through 20. Default is 8.
125 * - next -No argument. Used to separate blocks of keywords when
126 * there's more than one host adapter in the system.
129 * - Numeric arguments can be decimal or the '0x' form of hex notation. There
130 * _must_ be a colon between a keyword and its numeric argument, with no
132 * - Keywords are separated by commas, no spaces, in the standard kernel
133 * command-line manner.
134 * - A keyword in the 'nth' comma-separated command-line member will overwrite
135 * the 'nth' element of setup_args[]. A blank command-line member (in
136 * other words, a comma with no preceding keyword) will _not_ overwrite
137 * the corresponding setup_args[] element.
138 * - If a keyword is used more than once, the first one applies to the first
139 * SCSI host found, the second to the second card, etc, unless the 'next'
140 * keyword is used to change the order.
142 * Some amiboot examples (for insmod, use 'setup_strings' instead of 'wd33c93'):
143 * - wd33c93=nosync:255
146 * - wd33c93=disconnect:2,nosync:0x08,period:250
147 * - wd33c93=debug:0x1c
150 /* Normally, no defaults are specified */
151 static char *setup_args
[] = { "", "", "", "", "", "", "", "", "" };
153 static char *setup_strings
;
154 module_param(setup_strings
, charp
, 0);
156 static void wd33c93_execute(struct Scsi_Host
*instance
);
158 #ifdef CONFIG_WD33C93_PIO
160 read_wd33c93(const wd33c93_regs regs
, uchar reg_num
)
164 outb(reg_num
, regs
.SASR
);
165 data
= inb(regs
.SCMD
);
169 static inline unsigned long
170 read_wd33c93_count(const wd33c93_regs regs
)
174 outb(WD_TRANSFER_COUNT_MSB
, regs
.SASR
);
175 value
= inb(regs
.SCMD
) << 16;
176 value
|= inb(regs
.SCMD
) << 8;
177 value
|= inb(regs
.SCMD
);
182 read_aux_stat(const wd33c93_regs regs
)
184 return inb(regs
.SASR
);
188 write_wd33c93(const wd33c93_regs regs
, uchar reg_num
, uchar value
)
190 outb(reg_num
, regs
.SASR
);
191 outb(value
, regs
.SCMD
);
195 write_wd33c93_count(const wd33c93_regs regs
, unsigned long value
)
197 outb(WD_TRANSFER_COUNT_MSB
, regs
.SASR
);
198 outb((value
>> 16) & 0xff, regs
.SCMD
);
199 outb((value
>> 8) & 0xff, regs
.SCMD
);
200 outb( value
& 0xff, regs
.SCMD
);
203 #define write_wd33c93_cmd(regs, cmd) \
204 write_wd33c93((regs), WD_COMMAND, (cmd))
207 write_wd33c93_cdb(const wd33c93_regs regs
, uint len
, uchar cmnd
[])
211 outb(WD_CDB_1
, regs
.SASR
);
212 for (i
=0; i
<len
; i
++)
213 outb(cmnd
[i
], regs
.SCMD
);
216 #else /* CONFIG_WD33C93_PIO */
218 read_wd33c93(const wd33c93_regs regs
, uchar reg_num
)
220 *regs
.SASR
= reg_num
;
226 read_wd33c93_count(const wd33c93_regs regs
)
230 *regs
.SASR
= WD_TRANSFER_COUNT_MSB
;
232 value
= *regs
.SCMD
<< 16;
233 value
|= *regs
.SCMD
<< 8;
240 read_aux_stat(const wd33c93_regs regs
)
246 write_wd33c93(const wd33c93_regs regs
, uchar reg_num
, uchar value
)
248 *regs
.SASR
= reg_num
;
255 write_wd33c93_count(const wd33c93_regs regs
, unsigned long value
)
257 *regs
.SASR
= WD_TRANSFER_COUNT_MSB
;
259 *regs
.SCMD
= value
>> 16;
260 *regs
.SCMD
= value
>> 8;
266 write_wd33c93_cmd(const wd33c93_regs regs
, uchar cmd
)
268 *regs
.SASR
= WD_COMMAND
;
275 write_wd33c93_cdb(const wd33c93_regs regs
, uint len
, uchar cmnd
[])
279 *regs
.SASR
= WD_CDB_1
;
280 for (i
= 0; i
< len
; i
++)
281 *regs
.SCMD
= cmnd
[i
];
283 #endif /* CONFIG_WD33C93_PIO */
286 read_1_byte(const wd33c93_regs regs
)
291 write_wd33c93(regs
, WD_CONTROL
, CTRL_IDI
| CTRL_EDI
| CTRL_POLLED
);
292 write_wd33c93_cmd(regs
, WD_CMD_TRANS_INFO
| 0x80);
294 asr
= read_aux_stat(regs
);
296 x
= read_wd33c93(regs
, WD_DATA
);
297 } while (!(asr
& ASR_INT
));
301 static struct sx_period sx_table
[] = {
314 round_period(unsigned int period
)
318 for (x
= 1; sx_table
[x
].period_ns
; x
++) {
319 if ((period
<= sx_table
[x
- 0].period_ns
) &&
320 (period
> sx_table
[x
- 1].period_ns
)) {
328 calc_sync_xfer(unsigned int period
, unsigned int offset
)
332 period
*= 4; /* convert SDTR code to ns */
333 result
= sx_table
[round_period(period
)].reg_value
;
334 result
|= (offset
< OPTIMUM_SX_OFF
) ? offset
: OPTIMUM_SX_OFF
;
339 wd33c93_queuecommand(struct scsi_cmnd
*cmd
,
340 void (*done
)(struct scsi_cmnd
*))
342 struct WD33C93_hostdata
*hostdata
;
343 struct scsi_cmnd
*tmp
;
345 hostdata
= (struct WD33C93_hostdata
*) cmd
->device
->host
->hostdata
;
348 printk("Q-%d-%02x-%ld( ", cmd
->device
->id
, cmd
->cmnd
[0], cmd
->pid
))
350 /* Set up a few fields in the scsi_cmnd structure for our own use:
351 * - host_scribble is the pointer to the next cmd in the input queue
352 * - scsi_done points to the routine we call when a cmd is finished
353 * - result is what you'd expect
355 cmd
->host_scribble
= NULL
;
356 cmd
->scsi_done
= done
;
359 /* We use the Scsi_Pointer structure that's included with each command
360 * as a scratchpad (as it's intended to be used!). The handy thing about
361 * the SCp.xxx fields is that they're always associated with a given
362 * cmd, and are preserved across disconnect-reselect. This means we
363 * can pretty much ignore SAVE_POINTERS and RESTORE_POINTERS messages
364 * if we keep all the critical pointers and counters in SCp:
365 * - SCp.ptr is the pointer into the RAM buffer
366 * - SCp.this_residual is the size of that buffer
367 * - SCp.buffer points to the current scatter-gather buffer
368 * - SCp.buffers_residual tells us how many S.G. buffers there are
369 * - SCp.have_data_in is not used
370 * - SCp.sent_command is not used
371 * - SCp.phase records this command's SRCID_ER bit setting
375 cmd
->SCp
.buffer
= (struct scatterlist
*) cmd
->request_buffer
;
376 cmd
->SCp
.buffers_residual
= cmd
->use_sg
- 1;
377 cmd
->SCp
.ptr
= page_address(cmd
->SCp
.buffer
->page
) +
378 cmd
->SCp
.buffer
->offset
;
379 cmd
->SCp
.this_residual
= cmd
->SCp
.buffer
->length
;
381 cmd
->SCp
.buffer
= NULL
;
382 cmd
->SCp
.buffers_residual
= 0;
383 cmd
->SCp
.ptr
= (char *) cmd
->request_buffer
;
384 cmd
->SCp
.this_residual
= cmd
->request_bufflen
;
387 /* WD docs state that at the conclusion of a "LEVEL2" command, the
388 * status byte can be retrieved from the LUN register. Apparently,
389 * this is the case only for *uninterrupted* LEVEL2 commands! If
390 * there are any unexpected phases entered, even if they are 100%
391 * legal (different devices may choose to do things differently),
392 * the LEVEL2 command sequence is exited. This often occurs prior
393 * to receiving the status byte, in which case the driver does a
394 * status phase interrupt and gets the status byte on its own.
395 * While such a command can then be "resumed" (ie restarted to
396 * finish up as a LEVEL2 command), the LUN register will NOT be
397 * a valid status byte at the command's conclusion, and we must
398 * use the byte obtained during the earlier interrupt. Here, we
399 * preset SCp.Status to an illegal value (0xff) so that when
400 * this command finally completes, we can tell where the actual
401 * status byte is stored.
404 cmd
->SCp
.Status
= ILLEGAL_STATUS_BYTE
;
407 * Add the cmd to the end of 'input_Q'. Note that REQUEST SENSE
408 * commands are added to the head of the queue so that the desired
409 * sense data is not lost before REQUEST_SENSE executes.
412 spin_lock_irq(&hostdata
->lock
);
414 if (!(hostdata
->input_Q
) || (cmd
->cmnd
[0] == REQUEST_SENSE
)) {
415 cmd
->host_scribble
= (uchar
*) hostdata
->input_Q
;
416 hostdata
->input_Q
= cmd
;
417 } else { /* find the end of the queue */
418 for (tmp
= (struct scsi_cmnd
*) hostdata
->input_Q
;
420 tmp
= (struct scsi_cmnd
*) tmp
->host_scribble
) ;
421 tmp
->host_scribble
= (uchar
*) cmd
;
424 /* We know that there's at least one command in 'input_Q' now.
425 * Go see if any of them are runnable!
428 wd33c93_execute(cmd
->device
->host
);
430 DB(DB_QUEUE_COMMAND
, printk(")Q-%ld ", cmd
->pid
))
432 spin_unlock_irq(&hostdata
->lock
);
437 * This routine attempts to start a scsi command. If the host_card is
438 * already connected, we give up immediately. Otherwise, look through
439 * the input_Q, using the first command we find that's intended
440 * for a currently non-busy target/lun.
442 * wd33c93_execute() is always called with interrupts disabled or from
443 * the wd33c93_intr itself, which means that a wd33c93 interrupt
444 * cannot occur while we are in here.
447 wd33c93_execute(struct Scsi_Host
*instance
)
449 struct WD33C93_hostdata
*hostdata
=
450 (struct WD33C93_hostdata
*) instance
->hostdata
;
451 const wd33c93_regs regs
= hostdata
->regs
;
452 struct scsi_cmnd
*cmd
, *prev
;
454 DB(DB_EXECUTE
, printk("EX("))
455 if (hostdata
->selecting
|| hostdata
->connected
) {
456 DB(DB_EXECUTE
, printk(")EX-0 "))
461 * Search through the input_Q for a command destined
462 * for an idle target/lun.
465 cmd
= (struct scsi_cmnd
*) hostdata
->input_Q
;
468 if (!(hostdata
->busy
[cmd
->device
->id
] & (1 << cmd
->device
->lun
)))
471 cmd
= (struct scsi_cmnd
*) cmd
->host_scribble
;
474 /* quit if queue empty or all possible targets are busy */
477 DB(DB_EXECUTE
, printk(")EX-1 "))
481 /* remove command from queue */
484 prev
->host_scribble
= cmd
->host_scribble
;
486 hostdata
->input_Q
= (struct scsi_cmnd
*) cmd
->host_scribble
;
488 #ifdef PROC_STATISTICS
489 hostdata
->cmd_cnt
[cmd
->device
->id
]++;
493 * Start the selection process
496 if (cmd
->sc_data_direction
== DMA_TO_DEVICE
)
497 write_wd33c93(regs
, WD_DESTINATION_ID
, cmd
->device
->id
);
499 write_wd33c93(regs
, WD_DESTINATION_ID
, cmd
->device
->id
| DSTID_DPD
);
501 /* Now we need to figure out whether or not this command is a good
502 * candidate for disconnect/reselect. We guess to the best of our
503 * ability, based on a set of hierarchical rules. When several
504 * devices are operating simultaneously, disconnects are usually
505 * an advantage. In a single device system, or if only 1 device
506 * is being accessed, transfers usually go faster if disconnects
509 * + Commands should NEVER disconnect if hostdata->disconnect =
510 * DIS_NEVER (this holds for tape drives also), and ALWAYS
511 * disconnect if hostdata->disconnect = DIS_ALWAYS.
512 * + Tape drive commands should always be allowed to disconnect.
513 * + Disconnect should be allowed if disconnected_Q isn't empty.
514 * + Commands should NOT disconnect if input_Q is empty.
515 * + Disconnect should be allowed if there are commands in input_Q
516 * for a different target/lun. In this case, the other commands
517 * should be made disconnect-able, if not already.
519 * I know, I know - this code would flunk me out of any
520 * "C Programming 101" class ever offered. But it's easy
521 * to change around and experiment with for now.
524 cmd
->SCp
.phase
= 0; /* assume no disconnect */
525 if (hostdata
->disconnect
== DIS_NEVER
)
527 if (hostdata
->disconnect
== DIS_ALWAYS
)
529 if (cmd
->device
->type
== 1) /* tape drive? */
531 if (hostdata
->disconnected_Q
) /* other commands disconnected? */
533 if (!(hostdata
->input_Q
)) /* input_Q empty? */
535 for (prev
= (struct scsi_cmnd
*) hostdata
->input_Q
; prev
;
536 prev
= (struct scsi_cmnd
*) prev
->host_scribble
) {
537 if ((prev
->device
->id
!= cmd
->device
->id
) ||
538 (prev
->device
->lun
!= cmd
->device
->lun
)) {
539 for (prev
= (struct scsi_cmnd
*) hostdata
->input_Q
; prev
;
540 prev
= (struct scsi_cmnd
*) prev
->host_scribble
)
551 #ifdef PROC_STATISTICS
552 hostdata
->disc_allowed_cnt
[cmd
->device
->id
]++;
557 write_wd33c93(regs
, WD_SOURCE_ID
, ((cmd
->SCp
.phase
) ? SRCID_ER
: 0));
559 write_wd33c93(regs
, WD_TARGET_LUN
, cmd
->device
->lun
);
560 write_wd33c93(regs
, WD_SYNCHRONOUS_TRANSFER
,
561 hostdata
->sync_xfer
[cmd
->device
->id
]);
562 hostdata
->busy
[cmd
->device
->id
] |= (1 << cmd
->device
->lun
);
564 if ((hostdata
->level2
== L2_NONE
) ||
565 (hostdata
->sync_stat
[cmd
->device
->id
] == SS_UNSET
)) {
568 * Do a 'Select-With-ATN' command. This will end with
569 * one of the following interrupts:
570 * CSR_RESEL_AM: failure - can try again later.
571 * CSR_TIMEOUT: failure - give up.
572 * CSR_SELECT: success - proceed.
575 hostdata
->selecting
= cmd
;
577 /* Every target has its own synchronous transfer setting, kept in the
578 * sync_xfer array, and a corresponding status byte in sync_stat[].
579 * Each target's sync_stat[] entry is initialized to SX_UNSET, and its
580 * sync_xfer[] entry is initialized to the default/safe value. SS_UNSET
581 * means that the parameters are undetermined as yet, and that we
582 * need to send an SDTR message to this device after selection is
583 * complete: We set SS_FIRST to tell the interrupt routine to do so.
584 * If we've been asked not to try synchronous transfers on this
585 * target (and _all_ luns within it), we'll still send the SDTR message
586 * later, but at that time we'll negotiate for async by specifying a
587 * sync fifo depth of 0.
589 if (hostdata
->sync_stat
[cmd
->device
->id
] == SS_UNSET
)
590 hostdata
->sync_stat
[cmd
->device
->id
] = SS_FIRST
;
591 hostdata
->state
= S_SELECTING
;
592 write_wd33c93_count(regs
, 0); /* guarantee a DATA_PHASE interrupt */
593 write_wd33c93_cmd(regs
, WD_CMD_SEL_ATN
);
597 * Do a 'Select-With-ATN-Xfer' command. This will end with
598 * one of the following interrupts:
599 * CSR_RESEL_AM: failure - can try again later.
600 * CSR_TIMEOUT: failure - give up.
601 * anything else: success - proceed.
604 hostdata
->connected
= cmd
;
605 write_wd33c93(regs
, WD_COMMAND_PHASE
, 0);
607 /* copy command_descriptor_block into WD chip
608 * (take advantage of auto-incrementing)
611 write_wd33c93_cdb(regs
, cmd
->cmd_len
, cmd
->cmnd
);
613 /* The wd33c93 only knows about Group 0, 1, and 5 commands when
614 * it's doing a 'select-and-transfer'. To be safe, we write the
615 * size of the CDB into the OWN_ID register for every case. This
616 * way there won't be problems with vendor-unique, audio, etc.
619 write_wd33c93(regs
, WD_OWN_ID
, cmd
->cmd_len
);
621 /* When doing a non-disconnect command with DMA, we can save
622 * ourselves a DATA phase interrupt later by setting everything
626 if ((cmd
->SCp
.phase
== 0) && (hostdata
->no_dma
== 0)) {
627 if (hostdata
->dma_setup(cmd
,
628 (cmd
->sc_data_direction
== DMA_TO_DEVICE
) ?
629 DATA_OUT_DIR
: DATA_IN_DIR
))
630 write_wd33c93_count(regs
, 0); /* guarantee a DATA_PHASE interrupt */
632 write_wd33c93_count(regs
,
633 cmd
->SCp
.this_residual
);
634 write_wd33c93(regs
, WD_CONTROL
,
635 CTRL_IDI
| CTRL_EDI
| CTRL_DMA
);
636 hostdata
->dma
= D_DMA_RUNNING
;
639 write_wd33c93_count(regs
, 0); /* guarantee a DATA_PHASE interrupt */
641 hostdata
->state
= S_RUNNING_LEVEL2
;
642 write_wd33c93_cmd(regs
, WD_CMD_SEL_ATN_XFER
);
646 * Since the SCSI bus can handle only 1 connection at a time,
647 * we get out of here now. If the selection fails, or when
648 * the command disconnects, we'll come back to this routine
649 * to search the input_Q again...
653 printk("%s%ld)EX-2 ", (cmd
->SCp
.phase
) ? "d:" : "", cmd
->pid
))
657 transfer_pio(const wd33c93_regs regs
, uchar
* buf
, int cnt
,
658 int data_in_dir
, struct WD33C93_hostdata
*hostdata
)
663 printk("(%p,%d,%s:", buf
, cnt
, data_in_dir
? "in" : "out"))
665 write_wd33c93(regs
, WD_CONTROL
, CTRL_IDI
| CTRL_EDI
| CTRL_POLLED
);
666 write_wd33c93_count(regs
, cnt
);
667 write_wd33c93_cmd(regs
, WD_CMD_TRANS_INFO
);
670 asr
= read_aux_stat(regs
);
672 *buf
++ = read_wd33c93(regs
, WD_DATA
);
673 } while (!(asr
& ASR_INT
));
676 asr
= read_aux_stat(regs
);
678 write_wd33c93(regs
, WD_DATA
, *buf
++);
679 } while (!(asr
& ASR_INT
));
682 /* Note: we are returning with the interrupt UN-cleared.
683 * Since (presumably) an entire I/O operation has
684 * completed, the bus phase is probably different, and
685 * the interrupt routine will discover this when it
686 * responds to the uncleared int.
692 transfer_bytes(const wd33c93_regs regs
, struct scsi_cmnd
*cmd
,
695 struct WD33C93_hostdata
*hostdata
;
696 unsigned long length
;
698 hostdata
= (struct WD33C93_hostdata
*) cmd
->device
->host
->hostdata
;
700 /* Normally, you'd expect 'this_residual' to be non-zero here.
701 * In a series of scatter-gather transfers, however, this
702 * routine will usually be called with 'this_residual' equal
703 * to 0 and 'buffers_residual' non-zero. This means that a
704 * previous transfer completed, clearing 'this_residual', and
705 * now we need to setup the next scatter-gather buffer as the
706 * source or destination for THIS transfer.
708 if (!cmd
->SCp
.this_residual
&& cmd
->SCp
.buffers_residual
) {
710 --cmd
->SCp
.buffers_residual
;
711 cmd
->SCp
.this_residual
= cmd
->SCp
.buffer
->length
;
712 cmd
->SCp
.ptr
= page_address(cmd
->SCp
.buffer
->page
) +
713 cmd
->SCp
.buffer
->offset
;
716 write_wd33c93(regs
, WD_SYNCHRONOUS_TRANSFER
,
717 hostdata
->sync_xfer
[cmd
->device
->id
]);
719 /* 'hostdata->no_dma' is TRUE if we don't even want to try DMA.
720 * Update 'this_residual' and 'ptr' after 'transfer_pio()' returns.
723 if (hostdata
->no_dma
|| hostdata
->dma_setup(cmd
, data_in_dir
)) {
724 #ifdef PROC_STATISTICS
727 transfer_pio(regs
, (uchar
*) cmd
->SCp
.ptr
,
728 cmd
->SCp
.this_residual
, data_in_dir
, hostdata
);
729 length
= cmd
->SCp
.this_residual
;
730 cmd
->SCp
.this_residual
= read_wd33c93_count(regs
);
731 cmd
->SCp
.ptr
+= (length
- cmd
->SCp
.this_residual
);
734 /* We are able to do DMA (in fact, the Amiga hardware is
735 * already going!), so start up the wd33c93 in DMA mode.
736 * We set 'hostdata->dma' = D_DMA_RUNNING so that when the
737 * transfer completes and causes an interrupt, we're
738 * reminded to tell the Amiga to shut down its end. We'll
739 * postpone the updating of 'this_residual' and 'ptr'
744 #ifdef PROC_STATISTICS
747 write_wd33c93(regs
, WD_CONTROL
, CTRL_IDI
| CTRL_EDI
| CTRL_DMA
);
748 write_wd33c93_count(regs
, cmd
->SCp
.this_residual
);
750 if ((hostdata
->level2
>= L2_DATA
) ||
751 (hostdata
->level2
== L2_BASIC
&& cmd
->SCp
.phase
== 0)) {
752 write_wd33c93(regs
, WD_COMMAND_PHASE
, 0x45);
753 write_wd33c93_cmd(regs
, WD_CMD_SEL_ATN_XFER
);
754 hostdata
->state
= S_RUNNING_LEVEL2
;
756 write_wd33c93_cmd(regs
, WD_CMD_TRANS_INFO
);
758 hostdata
->dma
= D_DMA_RUNNING
;
763 wd33c93_intr(struct Scsi_Host
*instance
)
765 struct WD33C93_hostdata
*hostdata
=
766 (struct WD33C93_hostdata
*) instance
->hostdata
;
767 const wd33c93_regs regs
= hostdata
->regs
;
768 struct scsi_cmnd
*patch
, *cmd
;
769 uchar asr
, sr
, phs
, id
, lun
, *ucp
, msg
;
770 unsigned long length
, flags
;
772 asr
= read_aux_stat(regs
);
773 if (!(asr
& ASR_INT
) || (asr
& ASR_BSY
))
776 spin_lock_irqsave(&hostdata
->lock
, flags
);
778 #ifdef PROC_STATISTICS
782 cmd
= (struct scsi_cmnd
*) hostdata
->connected
; /* assume we're connected */
783 sr
= read_wd33c93(regs
, WD_SCSI_STATUS
); /* clear the interrupt */
784 phs
= read_wd33c93(regs
, WD_COMMAND_PHASE
);
786 DB(DB_INTR
, printk("{%02x:%02x-", asr
, sr
))
788 /* After starting a DMA transfer, the next interrupt
789 * is guaranteed to be in response to completion of
790 * the transfer. Since the Amiga DMA hardware runs in
791 * in an open-ended fashion, it needs to be told when
792 * to stop; do that here if D_DMA_RUNNING is true.
793 * Also, we have to update 'this_residual' and 'ptr'
794 * based on the contents of the TRANSFER_COUNT register,
795 * in case the device decided to do an intermediate
796 * disconnect (a device may do this if it has to do a
797 * seek, or just to be nice and let other devices have
798 * some bus time during long transfers). After doing
799 * whatever is needed, we go on and service the WD3393
800 * interrupt normally.
802 if (hostdata
->dma
== D_DMA_RUNNING
) {
804 printk("[%p/%d:", cmd
->SCp
.ptr
, cmd
->SCp
.this_residual
))
805 hostdata
->dma_stop(cmd
->device
->host
, cmd
, 1);
806 hostdata
->dma
= D_DMA_OFF
;
807 length
= cmd
->SCp
.this_residual
;
808 cmd
->SCp
.this_residual
= read_wd33c93_count(regs
);
809 cmd
->SCp
.ptr
+= (length
- cmd
->SCp
.this_residual
);
811 printk("%p/%d]", cmd
->SCp
.ptr
, cmd
->SCp
.this_residual
))
814 /* Respond to the specific WD3393 interrupt - there are quite a few! */
817 DB(DB_INTR
, printk("TIMEOUT"))
819 if (hostdata
->state
== S_RUNNING_LEVEL2
)
820 hostdata
->connected
= NULL
;
822 cmd
= (struct scsi_cmnd
*) hostdata
->selecting
; /* get a valid cmd */
823 hostdata
->selecting
= NULL
;
826 cmd
->result
= DID_NO_CONNECT
<< 16;
827 hostdata
->busy
[cmd
->device
->id
] &= ~(1 << cmd
->device
->lun
);
828 hostdata
->state
= S_UNCONNECTED
;
832 * There is a window of time within the scsi_done() path
833 * of execution where interrupts are turned back on full
834 * blast and left that way. During that time we could
835 * reconnect to a disconnected command, then we'd bomb
836 * out below. We could also end up executing two commands
837 * at _once_. ...just so you know why the restore_flags()
841 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
843 /* We are not connected to a target - check to see if there
844 * are commands waiting to be executed.
847 wd33c93_execute(instance
);
850 /* Note: this interrupt should not occur in a LEVEL2 command */
853 DB(DB_INTR
, printk("SELECT"))
854 hostdata
->connected
= cmd
=
855 (struct scsi_cmnd
*) hostdata
->selecting
;
856 hostdata
->selecting
= NULL
;
858 /* construct an IDENTIFY message with correct disconnect bit */
860 hostdata
->outgoing_msg
[0] = (0x80 | 0x00 | cmd
->device
->lun
);
862 hostdata
->outgoing_msg
[0] |= 0x40;
864 if (hostdata
->sync_stat
[cmd
->device
->id
] == SS_FIRST
) {
866 printk(" sending SDTR ");
869 hostdata
->sync_stat
[cmd
->device
->id
] = SS_WAITING
;
871 /* Tack on a 2nd message to ask about synchronous transfers. If we've
872 * been asked to do only asynchronous transfers on this device, we
873 * request a fifo depth of 0, which is equivalent to async - should
874 * solve the problems some people have had with GVP's Guru ROM.
877 hostdata
->outgoing_msg
[1] = EXTENDED_MESSAGE
;
878 hostdata
->outgoing_msg
[2] = 3;
879 hostdata
->outgoing_msg
[3] = EXTENDED_SDTR
;
880 if (hostdata
->no_sync
& (1 << cmd
->device
->id
)) {
881 hostdata
->outgoing_msg
[4] =
882 hostdata
->default_sx_per
/ 4;
883 hostdata
->outgoing_msg
[5] = 0;
885 hostdata
->outgoing_msg
[4] = OPTIMUM_SX_PER
/ 4;
886 hostdata
->outgoing_msg
[5] = OPTIMUM_SX_OFF
;
888 hostdata
->outgoing_len
= 6;
890 hostdata
->outgoing_len
= 1;
892 hostdata
->state
= S_CONNECTED
;
893 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
896 case CSR_XFER_DONE
| PHS_DATA_IN
:
897 case CSR_UNEXP
| PHS_DATA_IN
:
898 case CSR_SRV_REQ
| PHS_DATA_IN
:
900 printk("IN-%d.%d", cmd
->SCp
.this_residual
,
901 cmd
->SCp
.buffers_residual
))
902 transfer_bytes(regs
, cmd
, DATA_IN_DIR
);
903 if (hostdata
->state
!= S_RUNNING_LEVEL2
)
904 hostdata
->state
= S_CONNECTED
;
905 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
908 case CSR_XFER_DONE
| PHS_DATA_OUT
:
909 case CSR_UNEXP
| PHS_DATA_OUT
:
910 case CSR_SRV_REQ
| PHS_DATA_OUT
:
912 printk("OUT-%d.%d", cmd
->SCp
.this_residual
,
913 cmd
->SCp
.buffers_residual
))
914 transfer_bytes(regs
, cmd
, DATA_OUT_DIR
);
915 if (hostdata
->state
!= S_RUNNING_LEVEL2
)
916 hostdata
->state
= S_CONNECTED
;
917 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
920 /* Note: this interrupt should not occur in a LEVEL2 command */
922 case CSR_XFER_DONE
| PHS_COMMAND
:
923 case CSR_UNEXP
| PHS_COMMAND
:
924 case CSR_SRV_REQ
| PHS_COMMAND
:
925 DB(DB_INTR
, printk("CMND-%02x,%ld", cmd
->cmnd
[0], cmd
->pid
))
926 transfer_pio(regs
, cmd
->cmnd
, cmd
->cmd_len
, DATA_OUT_DIR
,
928 hostdata
->state
= S_CONNECTED
;
929 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
932 case CSR_XFER_DONE
| PHS_STATUS
:
933 case CSR_UNEXP
| PHS_STATUS
:
934 case CSR_SRV_REQ
| PHS_STATUS
:
935 DB(DB_INTR
, printk("STATUS="))
936 cmd
->SCp
.Status
= read_1_byte(regs
);
937 DB(DB_INTR
, printk("%02x", cmd
->SCp
.Status
))
938 if (hostdata
->level2
>= L2_BASIC
) {
939 sr
= read_wd33c93(regs
, WD_SCSI_STATUS
); /* clear interrupt */
941 hostdata
->state
= S_RUNNING_LEVEL2
;
942 write_wd33c93(regs
, WD_COMMAND_PHASE
, 0x50);
943 write_wd33c93_cmd(regs
, WD_CMD_SEL_ATN_XFER
);
945 hostdata
->state
= S_CONNECTED
;
947 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
950 case CSR_XFER_DONE
| PHS_MESS_IN
:
951 case CSR_UNEXP
| PHS_MESS_IN
:
952 case CSR_SRV_REQ
| PHS_MESS_IN
:
953 DB(DB_INTR
, printk("MSG_IN="))
955 msg
= read_1_byte(regs
);
956 sr
= read_wd33c93(regs
, WD_SCSI_STATUS
); /* clear interrupt */
959 hostdata
->incoming_msg
[hostdata
->incoming_ptr
] = msg
;
960 if (hostdata
->incoming_msg
[0] == EXTENDED_MESSAGE
)
961 msg
= EXTENDED_MESSAGE
;
963 hostdata
->incoming_ptr
= 0;
965 cmd
->SCp
.Message
= msg
;
968 case COMMAND_COMPLETE
:
969 DB(DB_INTR
, printk("CCMP-%ld", cmd
->pid
))
970 write_wd33c93_cmd(regs
, WD_CMD_NEGATE_ACK
);
971 hostdata
->state
= S_PRE_CMP_DISC
;
975 DB(DB_INTR
, printk("SDP"))
976 write_wd33c93_cmd(regs
, WD_CMD_NEGATE_ACK
);
977 hostdata
->state
= S_CONNECTED
;
980 case RESTORE_POINTERS
:
981 DB(DB_INTR
, printk("RDP"))
982 if (hostdata
->level2
>= L2_BASIC
) {
983 write_wd33c93(regs
, WD_COMMAND_PHASE
, 0x45);
984 write_wd33c93_cmd(regs
, WD_CMD_SEL_ATN_XFER
);
985 hostdata
->state
= S_RUNNING_LEVEL2
;
987 write_wd33c93_cmd(regs
, WD_CMD_NEGATE_ACK
);
988 hostdata
->state
= S_CONNECTED
;
993 DB(DB_INTR
, printk("DIS"))
994 cmd
->device
->disconnect
= 1;
995 write_wd33c93_cmd(regs
, WD_CMD_NEGATE_ACK
);
996 hostdata
->state
= S_PRE_TMP_DISC
;
1000 DB(DB_INTR
, printk("REJ"))
1004 if (hostdata
->sync_stat
[cmd
->device
->id
] == SS_WAITING
)
1005 hostdata
->sync_stat
[cmd
->device
->id
] = SS_SET
;
1006 write_wd33c93_cmd(regs
, WD_CMD_NEGATE_ACK
);
1007 hostdata
->state
= S_CONNECTED
;
1010 case EXTENDED_MESSAGE
:
1011 DB(DB_INTR
, printk("EXT"))
1013 ucp
= hostdata
->incoming_msg
;
1016 printk("%02x", ucp
[hostdata
->incoming_ptr
]);
1018 /* Is this the last byte of the extended message? */
1020 if ((hostdata
->incoming_ptr
>= 2) &&
1021 (hostdata
->incoming_ptr
== (ucp
[1] + 1))) {
1023 switch (ucp
[2]) { /* what's the EXTENDED code? */
1025 id
= calc_sync_xfer(ucp
[3], ucp
[4]);
1026 if (hostdata
->sync_stat
[cmd
->device
->id
] !=
1029 /* A device has sent an unsolicited SDTR message; rather than go
1030 * through the effort of decoding it and then figuring out what
1031 * our reply should be, we're just gonna say that we have a
1032 * synchronous fifo depth of 0. This will result in asynchronous
1033 * transfers - not ideal but so much easier.
1034 * Actually, this is OK because it assures us that if we don't
1035 * specifically ask for sync transfers, we won't do any.
1038 write_wd33c93_cmd(regs
, WD_CMD_ASSERT_ATN
); /* want MESS_OUT */
1039 hostdata
->outgoing_msg
[0] =
1041 hostdata
->outgoing_msg
[1] = 3;
1042 hostdata
->outgoing_msg
[2] =
1044 hostdata
->outgoing_msg
[3] =
1045 hostdata
->default_sx_per
/
1047 hostdata
->outgoing_msg
[4] = 0;
1048 hostdata
->outgoing_len
= 5;
1049 hostdata
->sync_xfer
[cmd
->device
->id
] =
1050 calc_sync_xfer(hostdata
->
1054 hostdata
->sync_xfer
[cmd
->device
->id
] = id
;
1057 printk("sync_xfer=%02x",
1058 hostdata
->sync_xfer
[cmd
->device
->id
]);
1060 hostdata
->sync_stat
[cmd
->device
->id
] =
1062 write_wd33c93_cmd(regs
,
1064 hostdata
->state
= S_CONNECTED
;
1067 write_wd33c93_cmd(regs
, WD_CMD_ASSERT_ATN
); /* want MESS_OUT */
1068 printk("sending WDTR ");
1069 hostdata
->outgoing_msg
[0] =
1071 hostdata
->outgoing_msg
[1] = 2;
1072 hostdata
->outgoing_msg
[2] =
1074 hostdata
->outgoing_msg
[3] = 0; /* 8 bit transfer width */
1075 hostdata
->outgoing_len
= 4;
1076 write_wd33c93_cmd(regs
,
1078 hostdata
->state
= S_CONNECTED
;
1081 write_wd33c93_cmd(regs
, WD_CMD_ASSERT_ATN
); /* want MESS_OUT */
1083 ("Rejecting Unknown Extended Message(%02x). ",
1085 hostdata
->outgoing_msg
[0] =
1087 hostdata
->outgoing_len
= 1;
1088 write_wd33c93_cmd(regs
,
1090 hostdata
->state
= S_CONNECTED
;
1093 hostdata
->incoming_ptr
= 0;
1096 /* We need to read more MESS_IN bytes for the extended message */
1099 hostdata
->incoming_ptr
++;
1100 write_wd33c93_cmd(regs
, WD_CMD_NEGATE_ACK
);
1101 hostdata
->state
= S_CONNECTED
;
1106 printk("Rejecting Unknown Message(%02x) ", msg
);
1107 write_wd33c93_cmd(regs
, WD_CMD_ASSERT_ATN
); /* want MESS_OUT */
1108 hostdata
->outgoing_msg
[0] = MESSAGE_REJECT
;
1109 hostdata
->outgoing_len
= 1;
1110 write_wd33c93_cmd(regs
, WD_CMD_NEGATE_ACK
);
1111 hostdata
->state
= S_CONNECTED
;
1113 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1116 /* Note: this interrupt will occur only after a LEVEL2 command */
1118 case CSR_SEL_XFER_DONE
:
1120 /* Make sure that reselection is enabled at this point - it may
1121 * have been turned off for the command that just completed.
1124 write_wd33c93(regs
, WD_SOURCE_ID
, SRCID_ER
);
1126 DB(DB_INTR
, printk("SX-DONE-%ld", cmd
->pid
))
1127 cmd
->SCp
.Message
= COMMAND_COMPLETE
;
1128 lun
= read_wd33c93(regs
, WD_TARGET_LUN
);
1129 DB(DB_INTR
, printk(":%d.%d", cmd
->SCp
.Status
, lun
))
1130 hostdata
->connected
= NULL
;
1131 hostdata
->busy
[cmd
->device
->id
] &= ~(1 << cmd
->device
->lun
);
1132 hostdata
->state
= S_UNCONNECTED
;
1133 if (cmd
->SCp
.Status
== ILLEGAL_STATUS_BYTE
)
1134 cmd
->SCp
.Status
= lun
;
1135 if (cmd
->cmnd
[0] == REQUEST_SENSE
1136 && cmd
->SCp
.Status
!= GOOD
)
1139 result
& 0x00ffff) | (DID_ERROR
<< 16);
1142 cmd
->SCp
.Status
| (cmd
->SCp
.Message
<< 8);
1143 cmd
->scsi_done(cmd
);
1145 /* We are no longer connected to a target - check to see if
1146 * there are commands waiting to be executed.
1148 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1149 wd33c93_execute(instance
);
1152 ("%02x:%02x:%02x-%ld: Unknown SEL_XFER_DONE phase!!---",
1153 asr
, sr
, phs
, cmd
->pid
);
1154 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1158 /* Note: this interrupt will occur only after a LEVEL2 command */
1161 DB(DB_INTR
, printk("SDP"))
1162 hostdata
->state
= S_RUNNING_LEVEL2
;
1163 write_wd33c93(regs
, WD_COMMAND_PHASE
, 0x41);
1164 write_wd33c93_cmd(regs
, WD_CMD_SEL_ATN_XFER
);
1165 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1168 case CSR_XFER_DONE
| PHS_MESS_OUT
:
1169 case CSR_UNEXP
| PHS_MESS_OUT
:
1170 case CSR_SRV_REQ
| PHS_MESS_OUT
:
1171 DB(DB_INTR
, printk("MSG_OUT="))
1173 /* To get here, we've probably requested MESSAGE_OUT and have
1174 * already put the correct bytes in outgoing_msg[] and filled
1175 * in outgoing_len. We simply send them out to the SCSI bus.
1176 * Sometimes we get MESSAGE_OUT phase when we're not expecting
1177 * it - like when our SDTR message is rejected by a target. Some
1178 * targets send the REJECT before receiving all of the extended
1179 * message, and then seem to go back to MESSAGE_OUT for a byte
1180 * or two. Not sure why, or if I'm doing something wrong to
1181 * cause this to happen. Regardless, it seems that sending
1182 * NOP messages in these situations results in no harm and
1183 * makes everyone happy.
1185 if (hostdata
->outgoing_len
== 0) {
1186 hostdata
->outgoing_len
= 1;
1187 hostdata
->outgoing_msg
[0] = NOP
;
1189 transfer_pio(regs
, hostdata
->outgoing_msg
,
1190 hostdata
->outgoing_len
, DATA_OUT_DIR
, hostdata
);
1191 DB(DB_INTR
, printk("%02x", hostdata
->outgoing_msg
[0]))
1192 hostdata
->outgoing_len
= 0;
1193 hostdata
->state
= S_CONNECTED
;
1194 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1197 case CSR_UNEXP_DISC
:
1199 /* I think I've seen this after a request-sense that was in response
1200 * to an error condition, but not sure. We certainly need to do
1201 * something when we get this interrupt - the question is 'what?'.
1202 * Let's think positively, and assume some command has finished
1203 * in a legal manner (like a command that provokes a request-sense),
1204 * so we treat it as a normal command-complete-disconnect.
1207 /* Make sure that reselection is enabled at this point - it may
1208 * have been turned off for the command that just completed.
1211 write_wd33c93(regs
, WD_SOURCE_ID
, SRCID_ER
);
1213 printk(" - Already disconnected! ");
1214 hostdata
->state
= S_UNCONNECTED
;
1215 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1218 DB(DB_INTR
, printk("UNEXP_DISC-%ld", cmd
->pid
))
1219 hostdata
->connected
= NULL
;
1220 hostdata
->busy
[cmd
->device
->id
] &= ~(1 << cmd
->device
->lun
);
1221 hostdata
->state
= S_UNCONNECTED
;
1222 if (cmd
->cmnd
[0] == REQUEST_SENSE
&& cmd
->SCp
.Status
!= GOOD
)
1224 (cmd
->result
& 0x00ffff) | (DID_ERROR
<< 16);
1226 cmd
->result
= cmd
->SCp
.Status
| (cmd
->SCp
.Message
<< 8);
1227 cmd
->scsi_done(cmd
);
1229 /* We are no longer connected to a target - check to see if
1230 * there are commands waiting to be executed.
1232 /* look above for comments on scsi_done() */
1233 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1234 wd33c93_execute(instance
);
1239 /* Make sure that reselection is enabled at this point - it may
1240 * have been turned off for the command that just completed.
1243 write_wd33c93(regs
, WD_SOURCE_ID
, SRCID_ER
);
1244 DB(DB_INTR
, printk("DISC-%ld", cmd
->pid
))
1246 printk(" - Already disconnected! ");
1247 hostdata
->state
= S_UNCONNECTED
;
1249 switch (hostdata
->state
) {
1250 case S_PRE_CMP_DISC
:
1251 hostdata
->connected
= NULL
;
1252 hostdata
->busy
[cmd
->device
->id
] &= ~(1 << cmd
->device
->lun
);
1253 hostdata
->state
= S_UNCONNECTED
;
1254 DB(DB_INTR
, printk(":%d", cmd
->SCp
.Status
))
1255 if (cmd
->cmnd
[0] == REQUEST_SENSE
1256 && cmd
->SCp
.Status
!= GOOD
)
1259 result
& 0x00ffff) | (DID_ERROR
<< 16);
1262 cmd
->SCp
.Status
| (cmd
->SCp
.Message
<< 8);
1263 cmd
->scsi_done(cmd
);
1265 case S_PRE_TMP_DISC
:
1266 case S_RUNNING_LEVEL2
:
1267 cmd
->host_scribble
= (uchar
*) hostdata
->disconnected_Q
;
1268 hostdata
->disconnected_Q
= cmd
;
1269 hostdata
->connected
= NULL
;
1270 hostdata
->state
= S_UNCONNECTED
;
1272 #ifdef PROC_STATISTICS
1273 hostdata
->disc_done_cnt
[cmd
->device
->id
]++;
1278 printk("*** Unexpected DISCONNECT interrupt! ***");
1279 hostdata
->state
= S_UNCONNECTED
;
1282 /* We are no longer connected to a target - check to see if
1283 * there are commands waiting to be executed.
1285 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1286 wd33c93_execute(instance
);
1291 DB(DB_INTR
, printk("RESEL%s", sr
== CSR_RESEL_AM
? "_AM" : ""))
1293 /* Old chips (pre -A ???) don't have advanced features and will
1294 * generate CSR_RESEL. In that case we have to extract the LUN the
1295 * hard way (see below).
1296 * First we have to make sure this reselection didn't
1297 * happen during Arbitration/Selection of some other device.
1298 * If yes, put losing command back on top of input_Q.
1300 if (hostdata
->level2
<= L2_NONE
) {
1302 if (hostdata
->selecting
) {
1303 cmd
= (struct scsi_cmnd
*) hostdata
->selecting
;
1304 hostdata
->selecting
= NULL
;
1305 hostdata
->busy
[cmd
->device
->id
] &= ~(1 << cmd
->device
->lun
);
1306 cmd
->host_scribble
=
1307 (uchar
*) hostdata
->input_Q
;
1308 hostdata
->input_Q
= cmd
;
1316 hostdata
->busy
[cmd
->device
->id
] &=
1317 ~(1 << cmd
->device
->lun
);
1318 cmd
->host_scribble
=
1319 (uchar
*) hostdata
->input_Q
;
1320 hostdata
->input_Q
= cmd
;
1323 ("---%02x:%02x:%02x-TROUBLE: Intrusive ReSelect!---",
1332 /* OK - find out which device reselected us. */
1334 id
= read_wd33c93(regs
, WD_SOURCE_ID
);
1337 /* and extract the lun from the ID message. (Note that we don't
1338 * bother to check for a valid message here - I guess this is
1339 * not the right way to go, but...)
1342 if (sr
== CSR_RESEL_AM
) {
1343 lun
= read_wd33c93(regs
, WD_DATA
);
1344 if (hostdata
->level2
< L2_RESELECT
)
1345 write_wd33c93_cmd(regs
, WD_CMD_NEGATE_ACK
);
1348 /* Old chip; wait for msgin phase to pick up the LUN. */
1349 for (lun
= 255; lun
; lun
--) {
1350 if ((asr
= read_aux_stat(regs
)) & ASR_INT
)
1354 if (!(asr
& ASR_INT
)) {
1356 ("wd33c93: Reselected without IDENTIFY\n");
1359 /* Verify this is a change to MSG_IN and read the message */
1360 sr
= read_wd33c93(regs
, WD_SCSI_STATUS
);
1362 if (sr
== (CSR_ABORT
| PHS_MESS_IN
) ||
1363 sr
== (CSR_UNEXP
| PHS_MESS_IN
) ||
1364 sr
== (CSR_SRV_REQ
| PHS_MESS_IN
)) {
1365 /* Got MSG_IN, grab target LUN */
1366 lun
= read_1_byte(regs
);
1367 /* Now we expect a 'paused with ACK asserted' int.. */
1368 asr
= read_aux_stat(regs
);
1369 if (!(asr
& ASR_INT
)) {
1371 asr
= read_aux_stat(regs
);
1372 if (!(asr
& ASR_INT
))
1374 ("wd33c93: No int after LUN on RESEL (%02x)\n",
1377 sr
= read_wd33c93(regs
, WD_SCSI_STATUS
);
1379 if (sr
!= CSR_MSGIN
)
1381 ("wd33c93: Not paused with ACK on RESEL (%02x)\n",
1384 write_wd33c93_cmd(regs
,
1388 ("wd33c93: Not MSG_IN on reselect (%02x)\n",
1395 /* Now we look for the command that's reconnecting. */
1397 cmd
= (struct scsi_cmnd
*) hostdata
->disconnected_Q
;
1400 if (id
== cmd
->device
->id
&& lun
== cmd
->device
->lun
)
1403 cmd
= (struct scsi_cmnd
*) cmd
->host_scribble
;
1406 /* Hmm. Couldn't find a valid command.... What to do? */
1410 ("---TROUBLE: target %d.%d not in disconnect queue---",
1412 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1416 /* Ok, found the command - now start it up again. */
1419 patch
->host_scribble
= cmd
->host_scribble
;
1421 hostdata
->disconnected_Q
=
1422 (struct scsi_cmnd
*) cmd
->host_scribble
;
1423 hostdata
->connected
= cmd
;
1425 /* We don't need to worry about 'initialize_SCp()' or 'hostdata->busy[]'
1426 * because these things are preserved over a disconnect.
1427 * But we DO need to fix the DPD bit so it's correct for this command.
1430 if (cmd
->sc_data_direction
== DMA_TO_DEVICE
)
1431 write_wd33c93(regs
, WD_DESTINATION_ID
, cmd
->device
->id
);
1433 write_wd33c93(regs
, WD_DESTINATION_ID
,
1434 cmd
->device
->id
| DSTID_DPD
);
1435 if (hostdata
->level2
>= L2_RESELECT
) {
1436 write_wd33c93_count(regs
, 0); /* we want a DATA_PHASE interrupt */
1437 write_wd33c93(regs
, WD_COMMAND_PHASE
, 0x45);
1438 write_wd33c93_cmd(regs
, WD_CMD_SEL_ATN_XFER
);
1439 hostdata
->state
= S_RUNNING_LEVEL2
;
1441 hostdata
->state
= S_CONNECTED
;
1443 DB(DB_INTR
, printk("-%ld", cmd
->pid
))
1444 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1448 printk("--UNKNOWN INTERRUPT:%02x:%02x:%02x--", asr
, sr
, phs
);
1449 spin_unlock_irqrestore(&hostdata
->lock
, flags
);
1452 DB(DB_INTR
, printk("} "))
1457 reset_wd33c93(struct Scsi_Host
*instance
)
1459 struct WD33C93_hostdata
*hostdata
=
1460 (struct WD33C93_hostdata
*) instance
->hostdata
;
1461 const wd33c93_regs regs
= hostdata
->regs
;
1464 #ifdef CONFIG_SGI_IP22
1467 extern void sgiwd93_reset(unsigned long);
1468 /* wait 'til the chip gets some time for us */
1469 while ((read_aux_stat(regs
) & ASR_BSY
) && busycount
++ < 100)
1472 * there are scsi devices out there, which manage to lock up
1473 * the wd33c93 in a busy condition. In this state it won't
1474 * accept the reset command. The only way to solve this is to
1475 * give the chip a hardware reset (if possible). The code below
1476 * does this for the SGI Indy, where this is possible
1479 if (read_aux_stat(regs
) & ASR_BSY
)
1480 sgiwd93_reset(instance
->base
); /* yeah, give it the hard one */
1484 write_wd33c93(regs
, WD_OWN_ID
, OWNID_EAF
| OWNID_RAF
|
1485 instance
->this_id
| hostdata
->clock_freq
);
1486 write_wd33c93(regs
, WD_CONTROL
, CTRL_IDI
| CTRL_EDI
| CTRL_POLLED
);
1487 write_wd33c93(regs
, WD_SYNCHRONOUS_TRANSFER
,
1488 calc_sync_xfer(hostdata
->default_sx_per
/ 4,
1490 write_wd33c93(regs
, WD_COMMAND
, WD_CMD_RESET
);
1493 #ifdef CONFIG_MVME147_SCSI
1494 udelay(25); /* The old wd33c93 on MVME147 needs this, at least */
1497 while (!(read_aux_stat(regs
) & ASR_INT
))
1499 sr
= read_wd33c93(regs
, WD_SCSI_STATUS
);
1501 hostdata
->microcode
= read_wd33c93(regs
, WD_CDB_1
);
1503 hostdata
->chip
= C_WD33C93
;
1504 else if (sr
== 0x01) {
1505 write_wd33c93(regs
, WD_QUEUE_TAG
, 0xa5); /* any random number */
1506 sr
= read_wd33c93(regs
, WD_QUEUE_TAG
);
1508 hostdata
->chip
= C_WD33C93B
;
1509 write_wd33c93(regs
, WD_QUEUE_TAG
, 0);
1511 hostdata
->chip
= C_WD33C93A
;
1513 hostdata
->chip
= C_UNKNOWN_CHIP
;
1515 write_wd33c93(regs
, WD_TIMEOUT_PERIOD
, TIMEOUT_PERIOD_VALUE
);
1516 write_wd33c93(regs
, WD_CONTROL
, CTRL_IDI
| CTRL_EDI
| CTRL_POLLED
);
1520 wd33c93_host_reset(struct scsi_cmnd
* SCpnt
)
1522 struct Scsi_Host
*instance
;
1523 struct WD33C93_hostdata
*hostdata
;
1526 instance
= SCpnt
->device
->host
;
1527 hostdata
= (struct WD33C93_hostdata
*) instance
->hostdata
;
1529 printk("scsi%d: reset. ", instance
->host_no
);
1530 disable_irq(instance
->irq
);
1532 hostdata
->dma_stop(instance
, NULL
, 0);
1533 for (i
= 0; i
< 8; i
++) {
1534 hostdata
->busy
[i
] = 0;
1535 hostdata
->sync_xfer
[i
] =
1536 calc_sync_xfer(DEFAULT_SX_PER
/ 4, DEFAULT_SX_OFF
);
1537 hostdata
->sync_stat
[i
] = SS_UNSET
; /* using default sync values */
1539 hostdata
->input_Q
= NULL
;
1540 hostdata
->selecting
= NULL
;
1541 hostdata
->connected
= NULL
;
1542 hostdata
->disconnected_Q
= NULL
;
1543 hostdata
->state
= S_UNCONNECTED
;
1544 hostdata
->dma
= D_DMA_OFF
;
1545 hostdata
->incoming_ptr
= 0;
1546 hostdata
->outgoing_len
= 0;
1548 reset_wd33c93(instance
);
1549 SCpnt
->result
= DID_RESET
<< 16;
1550 enable_irq(instance
->irq
);
1555 wd33c93_abort(struct scsi_cmnd
* cmd
)
1557 struct Scsi_Host
*instance
;
1558 struct WD33C93_hostdata
*hostdata
;
1560 struct scsi_cmnd
*tmp
, *prev
;
1562 disable_irq(cmd
->device
->host
->irq
);
1564 instance
= cmd
->device
->host
;
1565 hostdata
= (struct WD33C93_hostdata
*) instance
->hostdata
;
1566 regs
= hostdata
->regs
;
1569 * Case 1 : If the command hasn't been issued yet, we simply remove it
1573 tmp
= (struct scsi_cmnd
*) hostdata
->input_Q
;
1578 prev
->host_scribble
= cmd
->host_scribble
;
1581 (struct scsi_cmnd
*) cmd
->host_scribble
;
1582 cmd
->host_scribble
= NULL
;
1583 cmd
->result
= DID_ABORT
<< 16;
1585 ("scsi%d: Abort - removing command %ld from input_Q. ",
1586 instance
->host_no
, cmd
->pid
);
1587 enable_irq(cmd
->device
->host
->irq
);
1588 cmd
->scsi_done(cmd
);
1592 tmp
= (struct scsi_cmnd
*) tmp
->host_scribble
;
1596 * Case 2 : If the command is connected, we're going to fail the abort
1597 * and let the high level SCSI driver retry at a later time or
1600 * Timeouts, and therefore aborted commands, will be highly unlikely
1601 * and handling them cleanly in this situation would make the common
1602 * case of noresets less efficient, and would pollute our code. So,
1606 if (hostdata
->connected
== cmd
) {
1608 unsigned long timeout
;
1610 printk("scsi%d: Aborting connected command %ld - ",
1611 instance
->host_no
, cmd
->pid
);
1613 printk("stopping DMA - ");
1614 if (hostdata
->dma
== D_DMA_RUNNING
) {
1615 hostdata
->dma_stop(instance
, cmd
, 0);
1616 hostdata
->dma
= D_DMA_OFF
;
1619 printk("sending wd33c93 ABORT command - ");
1620 write_wd33c93(regs
, WD_CONTROL
,
1621 CTRL_IDI
| CTRL_EDI
| CTRL_POLLED
);
1622 write_wd33c93_cmd(regs
, WD_CMD_ABORT
);
1624 /* Now we have to attempt to flush out the FIFO... */
1626 printk("flushing fifo - ");
1629 asr
= read_aux_stat(regs
);
1631 read_wd33c93(regs
, WD_DATA
);
1632 } while (!(asr
& ASR_INT
) && timeout
-- > 0);
1633 sr
= read_wd33c93(regs
, WD_SCSI_STATUS
);
1635 ("asr=%02x, sr=%02x, %ld bytes un-transferred (timeout=%ld) - ",
1636 asr
, sr
, read_wd33c93_count(regs
), timeout
);
1639 * Abort command processed.
1641 * We must disconnect.
1644 printk("sending wd33c93 DISCONNECT command - ");
1645 write_wd33c93_cmd(regs
, WD_CMD_DISCONNECT
);
1648 asr
= read_aux_stat(regs
);
1649 while ((asr
& ASR_CIP
) && timeout
-- > 0)
1650 asr
= read_aux_stat(regs
);
1651 sr
= read_wd33c93(regs
, WD_SCSI_STATUS
);
1652 printk("asr=%02x, sr=%02x.", asr
, sr
);
1654 hostdata
->busy
[cmd
->device
->id
] &= ~(1 << cmd
->device
->lun
);
1655 hostdata
->connected
= NULL
;
1656 hostdata
->state
= S_UNCONNECTED
;
1657 cmd
->result
= DID_ABORT
<< 16;
1660 wd33c93_execute(instance
);
1662 enable_irq(cmd
->device
->host
->irq
);
1663 cmd
->scsi_done(cmd
);
1668 * Case 3: If the command is currently disconnected from the bus,
1669 * we're not going to expend much effort here: Let's just return
1670 * an ABORT_SNOOZE and hope for the best...
1673 tmp
= (struct scsi_cmnd
*) hostdata
->disconnected_Q
;
1677 ("scsi%d: Abort - command %ld found on disconnected_Q - ",
1678 instance
->host_no
, cmd
->pid
);
1679 printk("Abort SNOOZE. ");
1680 enable_irq(cmd
->device
->host
->irq
);
1683 tmp
= (struct scsi_cmnd
*) tmp
->host_scribble
;
1687 * Case 4 : If we reached this point, the command was not found in any of
1690 * We probably reached this point because of an unlikely race condition
1691 * between the command completing successfully and the abortion code,
1692 * so we won't panic, but we will notify the user in case something really
1697 wd33c93_execute(instance
);
1699 enable_irq(cmd
->device
->host
->irq
);
1700 printk("scsi%d: warning : SCSI command probably completed successfully"
1701 " before abortion. ", instance
->host_no
);
1705 #define MAX_WD33C93_HOSTS 4
1706 #define MAX_SETUP_ARGS ARRAY_SIZE(setup_args)
1707 #define SETUP_BUFFER_SIZE 200
1708 static char setup_buffer
[SETUP_BUFFER_SIZE
];
1709 static char setup_used
[MAX_SETUP_ARGS
];
1710 static int done_setup
= 0;
1713 wd33c93_setup(char *str
)
1718 /* The kernel does some processing of the command-line before calling
1719 * this function: If it begins with any decimal or hex number arguments,
1720 * ints[0] = how many numbers found and ints[1] through [n] are the values
1721 * themselves. str points to where the non-numeric arguments (if any)
1722 * start: We do our own parsing of those. We construct synthetic 'nosync'
1723 * keywords out of numeric args (to maintain compatibility with older
1724 * versions) and then add the rest of the arguments.
1730 strncpy(p1
, str
, SETUP_BUFFER_SIZE
- strlen(setup_buffer
));
1731 setup_buffer
[SETUP_BUFFER_SIZE
- 1] = '\0';
1734 while (*p1
&& (i
< MAX_SETUP_ARGS
)) {
1735 p2
= strchr(p1
, ',');
1747 for (i
= 0; i
< MAX_SETUP_ARGS
; i
++)
1753 __setup("wd33c93=", wd33c93_setup
);
1755 /* check_setup_args() returns index if key found, 0 if not
1758 check_setup_args(char *key
, int *flags
, int *val
, char *buf
)
1763 for (x
= 0; x
< MAX_SETUP_ARGS
; x
++) {
1766 if (!strncmp(setup_args
[x
], key
, strlen(key
)))
1768 if (!strncmp(setup_args
[x
], "next", strlen("next")))
1771 if (x
== MAX_SETUP_ARGS
)
1774 cp
= setup_args
[x
] + strlen(key
);
1779 if ((*cp
>= '0') && (*cp
<= '9')) {
1780 *val
= simple_strtoul(cp
, NULL
, 0);
1786 wd33c93_init(struct Scsi_Host
*instance
, const wd33c93_regs regs
,
1787 dma_setup_t setup
, dma_stop_t stop
, int clock_freq
)
1789 struct WD33C93_hostdata
*hostdata
;
1795 if (!done_setup
&& setup_strings
)
1796 wd33c93_setup(setup_strings
);
1798 hostdata
= (struct WD33C93_hostdata
*) instance
->hostdata
;
1800 hostdata
->regs
= regs
;
1801 hostdata
->clock_freq
= clock_freq
;
1802 hostdata
->dma_setup
= setup
;
1803 hostdata
->dma_stop
= stop
;
1804 hostdata
->dma_bounce_buffer
= NULL
;
1805 hostdata
->dma_bounce_len
= 0;
1806 for (i
= 0; i
< 8; i
++) {
1807 hostdata
->busy
[i
] = 0;
1808 hostdata
->sync_xfer
[i
] =
1809 calc_sync_xfer(DEFAULT_SX_PER
/ 4, DEFAULT_SX_OFF
);
1810 hostdata
->sync_stat
[i
] = SS_UNSET
; /* using default sync values */
1811 #ifdef PROC_STATISTICS
1812 hostdata
->cmd_cnt
[i
] = 0;
1813 hostdata
->disc_allowed_cnt
[i
] = 0;
1814 hostdata
->disc_done_cnt
[i
] = 0;
1817 hostdata
->input_Q
= NULL
;
1818 hostdata
->selecting
= NULL
;
1819 hostdata
->connected
= NULL
;
1820 hostdata
->disconnected_Q
= NULL
;
1821 hostdata
->state
= S_UNCONNECTED
;
1822 hostdata
->dma
= D_DMA_OFF
;
1823 hostdata
->level2
= L2_BASIC
;
1824 hostdata
->disconnect
= DIS_ADAPTIVE
;
1825 hostdata
->args
= DEBUG_DEFAULTS
;
1826 hostdata
->incoming_ptr
= 0;
1827 hostdata
->outgoing_len
= 0;
1828 hostdata
->default_sx_per
= DEFAULT_SX_PER
;
1829 hostdata
->no_sync
= 0xff; /* sync defaults to off */
1830 hostdata
->no_dma
= 0; /* default is DMA enabled */
1832 #ifdef PROC_INTERFACE
1833 hostdata
->proc
= PR_VERSION
| PR_INFO
| PR_STATISTICS
|
1834 PR_CONNECTED
| PR_INPUTQ
| PR_DISCQ
| PR_STOP
;
1835 #ifdef PROC_STATISTICS
1836 hostdata
->dma_cnt
= 0;
1837 hostdata
->pio_cnt
= 0;
1838 hostdata
->int_cnt
= 0;
1842 if (check_setup_args("nosync", &flags
, &val
, buf
))
1843 hostdata
->no_sync
= val
;
1845 if (check_setup_args("nodma", &flags
, &val
, buf
))
1846 hostdata
->no_dma
= (val
== -1) ? 1 : val
;
1848 if (check_setup_args("period", &flags
, &val
, buf
))
1849 hostdata
->default_sx_per
=
1850 sx_table
[round_period((unsigned int) val
)].period_ns
;
1852 if (check_setup_args("disconnect", &flags
, &val
, buf
)) {
1853 if ((val
>= DIS_NEVER
) && (val
<= DIS_ALWAYS
))
1854 hostdata
->disconnect
= val
;
1856 hostdata
->disconnect
= DIS_ADAPTIVE
;
1859 if (check_setup_args("level2", &flags
, &val
, buf
))
1860 hostdata
->level2
= val
;
1862 if (check_setup_args("debug", &flags
, &val
, buf
))
1863 hostdata
->args
= val
& DB_MASK
;
1865 if (check_setup_args("clock", &flags
, &val
, buf
)) {
1866 if (val
> 7 && val
< 11)
1867 val
= WD33C93_FS_8_10
;
1868 else if (val
> 11 && val
< 16)
1869 val
= WD33C93_FS_12_15
;
1870 else if (val
> 15 && val
< 21)
1871 val
= WD33C93_FS_16_20
;
1873 val
= WD33C93_FS_8_10
;
1874 hostdata
->clock_freq
= val
;
1877 if ((i
= check_setup_args("next", &flags
, &val
, buf
))) {
1879 setup_used
[--i
] = 1;
1881 #ifdef PROC_INTERFACE
1882 if (check_setup_args("proc", &flags
, &val
, buf
))
1883 hostdata
->proc
= val
;
1886 spin_lock_irq(&hostdata
->lock
);
1887 reset_wd33c93(instance
);
1888 spin_unlock_irq(&hostdata
->lock
);
1890 printk("wd33c93-%d: chip=%s/%d no_sync=0x%x no_dma=%d",
1892 (hostdata
->chip
== C_WD33C93
) ? "WD33c93" : (hostdata
->chip
==
1894 "WD33c93A" : (hostdata
->chip
==
1895 C_WD33C93B
) ? "WD33c93B" : "unknown",
1896 hostdata
->microcode
, hostdata
->no_sync
, hostdata
->no_dma
);
1898 printk(" debug_flags=0x%02x\n", hostdata
->args
);
1900 printk(" debugging=OFF\n");
1902 printk(" setup_args=");
1903 for (i
= 0; i
< MAX_SETUP_ARGS
; i
++)
1904 printk("%s,", setup_args
[i
]);
1906 printk(" Version %s - %s, Compiled %s at %s\n",
1907 WD33C93_VERSION
, WD33C93_DATE
, __DATE__
, __TIME__
);
1911 wd33c93_proc_info(struct Scsi_Host
*instance
, char *buf
, char **start
, off_t off
, int len
, int in
)
1914 #ifdef PROC_INTERFACE
1918 struct WD33C93_hostdata
*hd
;
1919 struct scsi_cmnd
*cmd
;
1921 static int stop
= 0;
1923 hd
= (struct WD33C93_hostdata
*) instance
->hostdata
;
1925 /* If 'in' is TRUE we need to _read_ the proc file. We accept the following
1926 * keywords (same format as command-line, but only ONE per read):
1938 if (!strncmp(bp
, "debug:", 6)) {
1940 hd
->args
= simple_strtoul(bp
, NULL
, 0) & DB_MASK
;
1941 } else if (!strncmp(bp
, "disconnect:", 11)) {
1943 x
= simple_strtoul(bp
, NULL
, 0);
1944 if (x
< DIS_NEVER
|| x
> DIS_ALWAYS
)
1947 } else if (!strncmp(bp
, "period:", 7)) {
1949 x
= simple_strtoul(bp
, NULL
, 0);
1950 hd
->default_sx_per
=
1951 sx_table
[round_period((unsigned int) x
)].period_ns
;
1952 } else if (!strncmp(bp
, "resync:", 7)) {
1954 x
= simple_strtoul(bp
, NULL
, 0);
1955 for (i
= 0; i
< 7; i
++)
1957 hd
->sync_stat
[i
] = SS_UNSET
;
1958 } else if (!strncmp(bp
, "proc:", 5)) {
1960 hd
->proc
= simple_strtoul(bp
, NULL
, 0);
1961 } else if (!strncmp(bp
, "nodma:", 6)) {
1963 hd
->no_dma
= simple_strtoul(bp
, NULL
, 0);
1964 } else if (!strncmp(bp
, "level2:", 7)) {
1966 hd
->level2
= simple_strtoul(bp
, NULL
, 0);
1971 spin_lock_irq(&hd
->lock
);
1974 if (hd
->proc
& PR_VERSION
) {
1975 sprintf(tbuf
, "\nVersion %s - %s. Compiled %s %s",
1976 WD33C93_VERSION
, WD33C93_DATE
, __DATE__
, __TIME__
);
1979 if (hd
->proc
& PR_INFO
) {
1980 sprintf(tbuf
, "\nclock_freq=%02x no_sync=%02x no_dma=%d",
1981 hd
->clock_freq
, hd
->no_sync
, hd
->no_dma
);
1983 strcat(bp
, "\nsync_xfer[] = ");
1984 for (x
= 0; x
< 7; x
++) {
1985 sprintf(tbuf
, "\t%02x", hd
->sync_xfer
[x
]);
1988 strcat(bp
, "\nsync_stat[] = ");
1989 for (x
= 0; x
< 7; x
++) {
1990 sprintf(tbuf
, "\t%02x", hd
->sync_stat
[x
]);
1994 #ifdef PROC_STATISTICS
1995 if (hd
->proc
& PR_STATISTICS
) {
1996 strcat(bp
, "\ncommands issued: ");
1997 for (x
= 0; x
< 7; x
++) {
1998 sprintf(tbuf
, "\t%ld", hd
->cmd_cnt
[x
]);
2001 strcat(bp
, "\ndisconnects allowed:");
2002 for (x
= 0; x
< 7; x
++) {
2003 sprintf(tbuf
, "\t%ld", hd
->disc_allowed_cnt
[x
]);
2006 strcat(bp
, "\ndisconnects done: ");
2007 for (x
= 0; x
< 7; x
++) {
2008 sprintf(tbuf
, "\t%ld", hd
->disc_done_cnt
[x
]);
2012 "\ninterrupts: %ld, DATA_PHASE ints: %ld DMA, %ld PIO",
2013 hd
->int_cnt
, hd
->dma_cnt
, hd
->pio_cnt
);
2017 if (hd
->proc
& PR_CONNECTED
) {
2018 strcat(bp
, "\nconnected: ");
2019 if (hd
->connected
) {
2020 cmd
= (struct scsi_cmnd
*) hd
->connected
;
2021 sprintf(tbuf
, " %ld-%d:%d(%02x)",
2022 cmd
->pid
, cmd
->device
->id
, cmd
->device
->lun
, cmd
->cmnd
[0]);
2026 if (hd
->proc
& PR_INPUTQ
) {
2027 strcat(bp
, "\ninput_Q: ");
2028 cmd
= (struct scsi_cmnd
*) hd
->input_Q
;
2030 sprintf(tbuf
, " %ld-%d:%d(%02x)",
2031 cmd
->pid
, cmd
->device
->id
, cmd
->device
->lun
, cmd
->cmnd
[0]);
2033 cmd
= (struct scsi_cmnd
*) cmd
->host_scribble
;
2036 if (hd
->proc
& PR_DISCQ
) {
2037 strcat(bp
, "\ndisconnected_Q:");
2038 cmd
= (struct scsi_cmnd
*) hd
->disconnected_Q
;
2040 sprintf(tbuf
, " %ld-%d:%d(%02x)",
2041 cmd
->pid
, cmd
->device
->id
, cmd
->device
->lun
, cmd
->cmnd
[0]);
2043 cmd
= (struct scsi_cmnd
*) cmd
->host_scribble
;
2047 spin_unlock_irq(&hd
->lock
);
2053 if (off
> 0x40000) /* ALWAYS stop after 256k bytes have been read */
2055 if (hd
->proc
& PR_STOP
) /* stop every other time */
2059 #else /* PROC_INTERFACE */
2063 #endif /* PROC_INTERFACE */
2068 wd33c93_release(void)
2072 EXPORT_SYMBOL(wd33c93_host_reset
);
2073 EXPORT_SYMBOL(wd33c93_init
);
2074 EXPORT_SYMBOL(wd33c93_release
);
2075 EXPORT_SYMBOL(wd33c93_abort
);
2076 EXPORT_SYMBOL(wd33c93_queuecommand
);
2077 EXPORT_SYMBOL(wd33c93_intr
);
2078 EXPORT_SYMBOL(wd33c93_proc_info
);