drivers/misc/eeprom/at25.c

   1 /*
   2  * at25.c -- support most SPI EEPROMs, such as Atmel AT25 models
   3  *
   4  * Copyright (C) 2006 David Brownell
   5  *
   6  * This program is free software; you can redistribute it and/or modify
   7  * it under the terms of the GNU General Public License as published by
   8  * the Free Software Foundation; either version 2 of the License, or
   9  * (at your option) any later version.
  10  */
  11
  12 #include <linux/kernel.h>
  13 #include <linux/init.h>
  14 #include <linux/module.h>
  15 #include <linux/slab.h>
  16 #include <linux/delay.h>
  17 #include <linux/device.h>
  18 #include <linux/sched.h>
  19
  20 #include <linux/spi/spi.h>
  21 #include <linux/spi/eeprom.h>
  22
  23
  24 /*
  25  * NOTE: this is an *EEPROM* driver.  The vagaries of product naming
  26  * mean that some AT25 products are EEPROMs, and others are FLASH.
  27  * Handle FLASH chips with the drivers/mtd/devices/m25p80.c driver,
  28  * not this one!
  29  */
  30
  31 struct at25_data {
  32         struct spi_device       *spi;
  33         struct memory_accessor  mem;
  34         struct mutex            lock;
  35         struct spi_eeprom       chip;
  36         struct bin_attribute    bin;
  37         unsigned                addrlen;
  38 };
  39
  40 #define AT25_WREN       0x06            /* latch the write enable */
  41 #define AT25_WRDI       0x04            /* reset the write enable */
  42 #define AT25_RDSR       0x05            /* read status register */
  43 #define AT25_WRSR       0x01            /* write status register */
  44 #define AT25_READ       0x03            /* read byte(s) */
  45 #define AT25_WRITE      0x02            /* write byte(s)/sector */
  46
  47 #define AT25_SR_nRDY    0x01            /* nRDY = write-in-progress */
  48 #define AT25_SR_WEN     0x02            /* write enable (latched) */
  49 #define AT25_SR_BP0     0x04            /* BP for software writeprotect */
  50 #define AT25_SR_BP1     0x08
  51 #define AT25_SR_WPEN    0x80            /* writeprotect enable */
  52
  53
  54 #define EE_MAXADDRLEN   3               /* 24 bit addresses, up to 2 MBytes */
  55
  56 /* Specs often allow 5 msec for a page write, sometimes 20 msec;
  57  * it's important to recover from write timeouts.
  58  */
  59 #define EE_TIMEOUT      25
  60
  61 /*-------------------------------------------------------------------------*/
  62
  63 #define io_limit        PAGE_SIZE       /* bytes */
  64
  65 static ssize_t
  66 at25_ee_read(
  67         struct at25_data        *at25,
  68         char                    *buf,
  69         unsigned                offset,
  70         size_t                  count
  71 )
  72 {
  73         u8                      command[EE_MAXADDRLEN + 1];
  74         u8                      *cp;
  75         ssize_t                 status;
  76         struct spi_transfer     t[2];
  77         struct spi_message      m;
  78
  79         if (unlikely(offset >= at25->bin.size))
  80                 return 0;
  81         if ((offset + count) > at25->bin.size)
  82                 count = at25->bin.size - offset;
  83         if (unlikely(!count))
  84                 return count;
  85
  86         cp = command;
  87         *cp++ = AT25_READ;
  88
  89         /* 8/16/24-bit address is written MSB first */
  90         switch (at25->addrlen) {
  91         default:        /* case 3 */
  92                 *cp++ = offset >> 16;
  93         case 2:
  94                 *cp++ = offset >> 8;
  95         case 1:
  96         case 0: /* can't happen: for better codegen */
  97                 *cp++ = offset >> 0;
  98         }
  99
 100         spi_message_init(&m);
 101         memset(t, 0, sizeof t);
 102
 103         t[0].tx_buf = command;
 104         t[0].len = at25->addrlen + 1;
 105         spi_message_add_tail(&t[0], &m);
 106
 107         t[1].rx_buf = buf;
 108         t[1].len = count;
 109         spi_message_add_tail(&t[1], &m);
 110
 111         mutex_lock(&at25->lock);
 112
 113         /* Read it all at once.
 114          *
 115          * REVISIT that's potentially a problem with large chips, if
 116          * other devices on the bus need to be accessed regularly or
 117          * this chip is clocked very slowly
 118          */
 119         status = spi_sync(at25->spi, &m);
 120         dev_dbg(&at25->spi->dev,
 121                 "read %Zd bytes at %d --> %d\n",
 122                 count, offset, (int) status);
 123
 124         mutex_unlock(&at25->lock);
 125         return status ? status : count;
 126 }
 127
 128 static ssize_t
 129 at25_bin_read(struct kobject *kobj, struct bin_attribute *bin_attr,
 130               char *buf, loff_t off, size_t count)
 131 {
 132         struct device           *dev;
 133         struct at25_data        *at25;
 134
 135         dev = container_of(kobj, struct device, kobj);
 136         at25 = dev_get_drvdata(dev);
 137
 138         return at25_ee_read(at25, buf, off, count);
 139 }
 140
 141
 142 static ssize_t
 143 at25_ee_write(struct at25_data *at25, const char *buf, loff_t off,
 144               size_t count)
 145 {
 146         ssize_t                 status = 0;
 147         unsigned                written = 0;
 148         unsigned                buf_size;
 149         u8                      *bounce;
 150
 151         if (unlikely(off >= at25->bin.size))
 152                 return -EFBIG;
 153         if ((off + count) > at25->bin.size)
 154                 count = at25->bin.size - off;
 155         if (unlikely(!count))
 156                 return count;
 157
 158         /* Temp buffer starts with command and address */
 159         buf_size = at25->chip.page_size;
 160         if (buf_size > io_limit)
 161                 buf_size = io_limit;
 162         bounce = kmalloc(buf_size + at25->addrlen + 1, GFP_KERNEL);
 163         if (!bounce)
 164                 return -ENOMEM;
 165
 166         /* For write, rollover is within the page ... so we write at
 167          * most one page, then manually roll over to the next page.
 168          */
 169         bounce[0] = AT25_WRITE;
 170         mutex_lock(&at25->lock);
 171         do {
 172                 unsigned long   timeout, retries;
 173                 unsigned        segment;
 174                 unsigned        offset = (unsigned) off;
 175                 u8              *cp = bounce + 1;
 176
 177                 *cp = AT25_WREN;
 178                 status = spi_write(at25->spi, cp, 1);
 179                 if (status < 0) {
 180                         dev_dbg(&at25->spi->dev, "WREN --> %d\n",
 181                                         (int) status);
 182                         break;
 183                 }
 184
 185                 /* 8/16/24-bit address is written MSB first */
 186                 switch (at25->addrlen) {
 187                 default:        /* case 3 */
 188                         *cp++ = offset >> 16;
 189                 case 2:
 190                         *cp++ = offset >> 8;
 191                 case 1:
 192                 case 0: /* can't happen: for better codegen */
 193                         *cp++ = offset >> 0;
 194                 }
 195
 196                 /* Write as much of a page as we can */
 197                 segment = buf_size - (offset % buf_size);
 198                 if (segment > count)
 199                         segment = count;
 200                 memcpy(cp, buf, segment);
 201                 status = spi_write(at25->spi, bounce,
 202                                 segment + at25->addrlen + 1);
 203                 dev_dbg(&at25->spi->dev,
 204                                 "write %u bytes at %u --> %d\n",
 205                                 segment, offset, (int) status);
 206                 if (status < 0)
 207                         break;
 208
 209                 /* REVISIT this should detect (or prevent) failed writes
 210                  * to readonly sections of the EEPROM...
 211                  */
 212
 213                 /* Wait for non-busy status */
 214                 timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT);
 215                 retries = 0;
 216                 do {
 217                         int     sr;
 218
 219                         sr = spi_w8r8(at25->spi, AT25_RDSR);
 220                         if (sr < 0 || (sr & AT25_SR_nRDY)) {
 221                                 dev_dbg(&at25->spi->dev,
 222                                         "rdsr --> %d (%02x)\n", sr, sr);
 223                                 /* at HZ=100, this is sloooow */
 224                                 msleep(1);
 225                                 continue;
 226                         }
 227                         if (!(sr & AT25_SR_nRDY))
 228                                 break;
 229                 } while (retries++ < 3 || time_before_eq(jiffies, timeout));
 230
 231                 if (time_after(jiffies, timeout)) {
 232                         dev_err(&at25->spi->dev,
 233                                 "write %d bytes offset %d, "
 234                                 "timeout after %u msecs\n",
 235                                 segment, offset,
 236                                 jiffies_to_msecs(jiffies -
 237                                         (timeout - EE_TIMEOUT)));
 238                         status = -ETIMEDOUT;
 239                         break;
 240                 }
 241
 242                 off += segment;
 243                 buf += segment;
 244                 count -= segment;
 245                 written += segment;
 246
 247         } while (count > 0);
 248
 249         mutex_unlock(&at25->lock);
 250
 251         kfree(bounce);
 252         return written ? written : status;
 253 }
 254
 255 static ssize_t
 256 at25_bin_write(struct kobject *kobj, struct bin_attribute *bin_attr,
 257                char *buf, loff_t off, size_t count)
 258 {
 259         struct device           *dev;
 260         struct at25_data        *at25;
 261
 262         dev = container_of(kobj, struct device, kobj);
 263         at25 = dev_get_drvdata(dev);
 264
 265         return at25_ee_write(at25, buf, off, count);
 266 }
 267
 268 /*-------------------------------------------------------------------------*/
 269
 270 /* Let in-kernel code access the eeprom data. */
 271
 272 static ssize_t at25_mem_read(struct memory_accessor *mem, char *buf,
 273                          off_t offset, size_t count)
 274 {
 275         struct at25_data *at25 = container_of(mem, struct at25_data, mem);
 276
 277         return at25_ee_read(at25, buf, offset, count);
 278 }
 279
 280 static ssize_t at25_mem_write(struct memory_accessor *mem, const char *buf,
 281                           off_t offset, size_t count)
 282 {
 283         struct at25_data *at25 = container_of(mem, struct at25_data, mem);
 284
 285         return at25_ee_write(at25, buf, offset, count);
 286 }
 287
 288 /*-------------------------------------------------------------------------*/
 289
 290 static int at25_probe(struct spi_device *spi)
 291 {
 292         struct at25_data        *at25 = NULL;
 293         const struct spi_eeprom *chip;
 294         int                     err;
 295         int                     sr;
 296         int                     addrlen;
 297
 298         /* Chip description */
 299         chip = spi->dev.platform_data;
 300         if (!chip) {
 301                 dev_dbg(&spi->dev, "no chip description\n");
 302                 err = -ENODEV;
 303                 goto fail;
 304         }
 305
 306         /* For now we only support 8/16/24 bit addressing */
 307         if (chip->flags & EE_ADDR1)
 308                 addrlen = 1;
 309         else if (chip->flags & EE_ADDR2)
 310                 addrlen = 2;
 311         else if (chip->flags & EE_ADDR3)
 312                 addrlen = 3;
 313         else {
 314                 dev_dbg(&spi->dev, "unsupported address type\n");
 315                 err = -EINVAL;
 316                 goto fail;
 317         }
 318
 319         /* Ping the chip ... the status register is pretty portable,
 320          * unlike probing manufacturer IDs.  We do expect that system
 321          * firmware didn't write it in the past few milliseconds!
 322          */
 323         sr = spi_w8r8(spi, AT25_RDSR);
 324         if (sr < 0 || sr & AT25_SR_nRDY) {
 325                 dev_dbg(&spi->dev, "rdsr --> %d (%02x)\n", sr, sr);
 326                 err = -ENXIO;
 327                 goto fail;
 328         }
 329
 330         if (!(at25 = kzalloc(sizeof *at25, GFP_KERNEL))) {
 331                 err = -ENOMEM;
 332                 goto fail;
 333         }
 334
 335         mutex_init(&at25->lock);
 336         at25->chip = *chip;
 337         at25->spi = spi_dev_get(spi);
 338         dev_set_drvdata(&spi->dev, at25);
 339         at25->addrlen = addrlen;
 340
 341         /* Export the EEPROM bytes through sysfs, since that's convenient.
 342          * And maybe to other kernel code; it might hold a board's Ethernet
 343          * address, or board-specific calibration data generated on the
 344          * manufacturing floor.
 345          *
 346          * Default to root-only access to the data; EEPROMs often hold data
 347          * that's sensitive for read and/or write, like ethernet addresses,
 348          * security codes, board-specific manufacturing calibrations, etc.
 349          */
 350         at25->bin.attr.name = "eeprom";
 351         at25->bin.attr.mode = S_IRUSR;
 352         at25->bin.read = at25_bin_read;
 353         at25->mem.read = at25_mem_read;
 354
 355         at25->bin.size = at25->chip.byte_len;
 356         if (!(chip->flags & EE_READONLY)) {
 357                 at25->bin.write = at25_bin_write;
 358                 at25->bin.attr.mode |= S_IWUSR;
 359                 at25->mem.write = at25_mem_write;
 360         }
 361
 362         err = sysfs_create_bin_file(&spi->dev.kobj, &at25->bin);
 363         if (err)
 364                 goto fail;
 365
 366         if (chip->setup)
 367                 chip->setup(&at25->mem, chip->context);
 368
 369         dev_info(&spi->dev, "%Zd %s %s eeprom%s, pagesize %u\n",
 370                 (at25->bin.size < 1024)
 371                         ? at25->bin.size
 372                         : (at25->bin.size / 1024),
 373                 (at25->bin.size < 1024) ? "Byte" : "KByte",
 374                 at25->chip.name,
 375                 (chip->flags & EE_READONLY) ? " (readonly)" : "",
 376                 at25->chip.page_size);
 377         return 0;
 378 fail:
 379         dev_dbg(&spi->dev, "probe err %d\n", err);
 380         kfree(at25);
 381         return err;
 382 }
 383
 384 static int __devexit at25_remove(struct spi_device *spi)
 385 {
 386         struct at25_data        *at25;
 387
 388         at25 = dev_get_drvdata(&spi->dev);
 389         sysfs_remove_bin_file(&spi->dev.kobj, &at25->bin);
 390         kfree(at25);
 391         return 0;
 392 }
 393
 394 /*-------------------------------------------------------------------------*/
 395
 396 static struct spi_driver at25_driver = {
 397         .driver = {
 398                 .name           = "at25",
 399                 .owner          = THIS_MODULE,
 400         },
 401         .probe          = at25_probe,
 402         .remove         = __devexit_p(at25_remove),
 403 };
 404
 405 static int __init at25_init(void)
 406 {
 407         return spi_register_driver(&at25_driver);
 408 }
 409 module_init(at25_init);
 410
 411 static void __exit at25_exit(void)
 412 {
 413         spi_unregister_driver(&at25_driver);
 414 }
 415 module_exit(at25_exit);
 416
 417 MODULE_DESCRIPTION("Driver for most SPI EEPROMs");
 418 MODULE_AUTHOR("David Brownell");
 419 MODULE_LICENSE("GPL");
 420