drivers/net/e2100.c

   1 /* e2100.c: A Cabletron E2100 series ethernet driver for linux. */
   2 /*
   3         Written 1993-1994 by Donald Becker.
   4
   5         Copyright 1994 by Donald Becker.
   6         Copyright 1993 United States Government as represented by the
   7         Director, National Security Agency.  This software may be used and
   8         distributed according to the terms of the GNU General Public License,
   9         incorporated herein by reference.
  10
  11         This is a driver for the Cabletron E2100 series ethercards.
  12
  13         The Author may be reached as becker@scyld.com, or C/O
  14         Scyld Computing Corporation
  15         410 Severn Ave., Suite 210
  16         Annapolis MD 21403
  17
  18         The E2100 series ethercard is a fairly generic shared memory 8390
  19         implementation.  The only unusual aspect is the way the shared memory
  20         registers are set: first you do an inb() in what is normally the
  21         station address region, and the low three bits of next outb() *address*
  22         is used as the write value for that register.  Either someone wasn't
  23         too used to dem bit en bites, or they were trying to obfuscate the
  24         programming interface.
  25
  26         There is an additional complication when setting the window on the packet
  27         buffer.  You must first do a read into the packet buffer region with the
  28         low 8 address bits the address setting the page for the start of the packet
  29         buffer window, and then do the above operation.  See mem_on() for details.
  30
  31         One bug on the chip is that even a hard reset won't disable the memory
  32         window, usually resulting in a hung machine if mem_off() isn't called.
  33         If this happens, you must power down the machine for about 30 seconds.
  34 */
  35
  36 static const char version[] =
  37         "e2100.c:v1.01 7/21/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n";
  38
  39 #include <linux/module.h>
  40 #include <linux/kernel.h>
  41 #include <linux/errno.h>
  42 #include <linux/string.h>
  43 #include <linux/ioport.h>
  44 #include <linux/netdevice.h>
  45 #include <linux/etherdevice.h>
  46 #include <linux/init.h>
  47 #include <linux/delay.h>
  48
  49 #include <asm/io.h>
  50 #include <asm/system.h>
  51
  52 #include "8390.h"
  53
  54 #define DRV_NAME "e2100"
  55
  56 static int e21_probe_list[] = {0x300, 0x280, 0x380, 0x220, 0};
  57
  58 /* Offsets from the base_addr.
  59    Read from the ASIC register, and the low three bits of the next outb()
  60    address is used to set the corresponding register. */
  61 #define E21_NIC_OFFSET  0               /* Offset to the 8390 NIC. */
  62 #define E21_ASIC                0x10
  63 #define E21_MEM_ENABLE  0x10
  64 #define  E21_MEM_ON             0x05    /* Enable memory in 16 bit mode. */
  65 #define  E21_MEM_ON_8   0x07    /* Enable memory in  8 bit mode. */
  66 #define E21_MEM_BASE    0x11
  67 #define E21_IRQ_LOW             0x12    /* The low three bits of the IRQ number. */
  68 #define E21_IRQ_HIGH    0x14    /* The high IRQ bit and media select ...  */
  69 #define E21_MEDIA               0x14    /* (alias). */
  70 #define  E21_ALT_IFPORT 0x02    /* Set to use the other (BNC,AUI) port. */
  71 #define  E21_BIG_MEM    0x04    /* Use a bigger (64K) buffer (we don't) */
  72 #define E21_SAPROM              0x10    /* Offset to station address data. */
  73 #define E21_IO_EXTENT    0x20
  74
  75 static inline void mem_on(short port, volatile char __iomem *mem_base,
  76                                                   unsigned char start_page )
  77 {
  78         /* This is a little weird: set the shared memory window by doing a
  79            read.  The low address bits specify the starting page. */
  80         readb(mem_base+start_page);
  81         inb(port + E21_MEM_ENABLE);
  82         outb(E21_MEM_ON, port + E21_MEM_ENABLE + E21_MEM_ON);
  83 }
  84
  85 static inline void mem_off(short port)
  86 {
  87         inb(port + E21_MEM_ENABLE);
  88         outb(0x00, port + E21_MEM_ENABLE);
  89 }
  90
  91 /* In other drivers I put the TX pages first, but the E2100 window circuitry
  92    is designed to have a 4K Tx region last. The windowing circuitry wraps the
  93    window at 0x2fff->0x0000 so that the packets at e.g. 0x2f00 in the RX ring
  94    appear contiguously in the window. */
  95 #define E21_RX_START_PG         0x00    /* First page of RX buffer */
  96 #define E21_RX_STOP_PG          0x30    /* Last page +1 of RX ring */
  97 #define E21_BIG_RX_STOP_PG      0xF0    /* Last page +1 of RX ring */
  98 #define E21_TX_START_PG         E21_RX_STOP_PG  /* First page of TX buffer */
  99
 100 static int e21_probe1(struct net_device *dev, int ioaddr);
 101
 102 static int e21_open(struct net_device *dev);
 103 static void e21_reset_8390(struct net_device *dev);
 104 static void e21_block_input(struct net_device *dev, int count,
 105                                                    struct sk_buff *skb, int ring_offset);
 106 static void e21_block_output(struct net_device *dev, int count,
 107                                                          const unsigned char *buf, int start_page);
 108 static void e21_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
 109                                                         int ring_page);
 110 static int e21_open(struct net_device *dev);
 111 static int e21_close(struct net_device *dev);
 112
 113
 114 /*  Probe for the E2100 series ethercards.  These cards have an 8390 at the
 115         base address and the station address at both offset 0x10 and 0x18.  I read
 116         the station address from offset 0x18 to avoid the dataport of NE2000
 117         ethercards, and look for Ctron's unique ID (first three octets of the
 118         station address).
 119  */
 120
 121 static int  __init do_e2100_probe(struct net_device *dev)
 122 {
 123         int *port;
 124         int base_addr = dev->base_addr;
 125         int irq = dev->irq;
 126
 127         if (base_addr > 0x1ff)          /* Check a single specified location. */
 128                 return e21_probe1(dev, base_addr);
 129         else if (base_addr != 0)        /* Don't probe at all. */
 130                 return -ENXIO;
 131
 132         for (port = e21_probe_list; *port; port++) {
 133                 dev->irq = irq;
 134                 if (e21_probe1(dev, *port) == 0)
 135                         return 0;
 136         }
 137
 138         return -ENODEV;
 139 }
 140
 141 #ifndef MODULE
 142 struct net_device * __init e2100_probe(int unit)
 143 {
 144         struct net_device *dev = alloc_ei_netdev();
 145         int err;
 146
 147         if (!dev)
 148                 return ERR_PTR(-ENOMEM);
 149
 150         sprintf(dev->name, "eth%d", unit);
 151         netdev_boot_setup_check(dev);
 152
 153         err = do_e2100_probe(dev);
 154         if (err)
 155                 goto out;
 156         return dev;
 157 out:
 158         free_netdev(dev);
 159         return ERR_PTR(err);
 160 }
 161 #endif
 162
 163 static const struct net_device_ops e21_netdev_ops = {
 164         .ndo_open               = e21_open,
 165         .ndo_stop               = e21_close,
 166
 167         .ndo_start_xmit         = ei_start_xmit,
 168         .ndo_tx_timeout         = ei_tx_timeout,
 169         .ndo_get_stats          = ei_get_stats,
 170         .ndo_set_multicast_list = ei_set_multicast_list,
 171         .ndo_validate_addr      = eth_validate_addr,
 172         .ndo_set_mac_address    = eth_mac_addr,
 173         .ndo_change_mtu         = eth_change_mtu,
 174 #ifdef CONFIG_NET_POLL_CONTROLLER
 175         .ndo_poll_controller    = ei_poll,
 176 #endif
 177 };
 178
 179 static int __init e21_probe1(struct net_device *dev, int ioaddr)
 180 {
 181         int i, status, retval;
 182         unsigned char *station_addr = dev->dev_addr;
 183         static unsigned version_printed;
 184
 185         if (!request_region(ioaddr, E21_IO_EXTENT, DRV_NAME))
 186                 return -EBUSY;
 187
 188         /* First check the station address for the Ctron prefix. */
 189         if (inb(ioaddr + E21_SAPROM + 0) != 0x00
 190                 || inb(ioaddr + E21_SAPROM + 1) != 0x00
 191                 || inb(ioaddr + E21_SAPROM + 2) != 0x1d) {
 192                 retval = -ENODEV;
 193                 goto out;
 194         }
 195
 196         /* Verify by making certain that there is a 8390 at there. */
 197         outb(E8390_NODMA + E8390_STOP, ioaddr);
 198         udelay(1);      /* we want to delay one I/O cycle - which is 2MHz */
 199         status = inb(ioaddr);
 200         if (status != 0x21 && status != 0x23) {
 201                 retval = -ENODEV;
 202                 goto out;
 203         }
 204
 205         /* Read the station address PROM.  */
 206         for (i = 0; i < 6; i++)
 207                 station_addr[i] = inb(ioaddr + E21_SAPROM + i);
 208
 209         inb(ioaddr + E21_MEDIA);                /* Point to media selection. */
 210         outb(0, ioaddr + E21_ASIC);     /* and disable the secondary interface. */
 211
 212         if (ei_debug  &&  version_printed++ == 0)
 213                 printk(version);
 214
 215         for (i = 0; i < 6; i++)
 216                 printk(" %02X", station_addr[i]);
 217
 218         if (dev->irq < 2) {
 219                 int irqlist[] = {15,11,10,12,5,9,3,4}, i;
 220                 for (i = 0; i < 8; i++)
 221                         if (request_irq (irqlist[i], NULL, 0, "bogus", NULL) != -EBUSY) {
 222                                 dev->irq = irqlist[i];
 223                                 break;
 224                         }
 225                 if (i >= 8) {
 226                         printk(" unable to get IRQ %d.\n", dev->irq);
 227                         retval = -EAGAIN;
 228                         goto out;
 229                 }
 230         } else if (dev->irq == 2)       /* Fixup luser bogosity: IRQ2 is really IRQ9 */
 231                 dev->irq = 9;
 232
 233         /* The 8390 is at the base address. */
 234         dev->base_addr = ioaddr;
 235
 236         ei_status.name = "E2100";
 237         ei_status.word16 = 1;
 238         ei_status.tx_start_page = E21_TX_START_PG;
 239         ei_status.rx_start_page = E21_RX_START_PG;
 240         ei_status.stop_page = E21_RX_STOP_PG;
 241         ei_status.saved_irq = dev->irq;
 242
 243         /* Check the media port used.  The port can be passed in on the
 244            low mem_end bits. */
 245         if (dev->mem_end & 15)
 246                 dev->if_port = dev->mem_end & 7;
 247         else {
 248                 dev->if_port = 0;
 249                 inb(ioaddr + E21_MEDIA);        /* Turn automatic media detection on. */
 250                 for(i = 0; i < 6; i++)
 251                         if (station_addr[i] != inb(ioaddr + E21_SAPROM + 8 + i)) {
 252                                 dev->if_port = 1;
 253                                 break;
 254                         }
 255         }
 256
 257         /* Never map in the E21 shared memory unless you are actively using it.
 258            Also, the shared memory has effective only one setting -- spread all
 259            over the 128K region! */
 260         if (dev->mem_start == 0)
 261                 dev->mem_start = 0xd0000;
 262
 263         ei_status.mem = ioremap(dev->mem_start, 2*1024);
 264         if (!ei_status.mem) {
 265                 printk("unable to remap memory\n");
 266                 retval = -EAGAIN;
 267                 goto out;
 268         }
 269
 270 #ifdef notdef
 271         /* These values are unused.  The E2100 has a 2K window into the packet
 272            buffer.  The window can be set to start on any page boundary. */
 273         ei_status.rmem_start = dev->mem_start + TX_PAGES*256;
 274         dev->mem_end = ei_status.rmem_end = dev->mem_start + 2*1024;
 275 #endif
 276
 277         printk(", IRQ %d, %s media, memory @ %#lx.\n", dev->irq,
 278                    dev->if_port ? "secondary" : "primary", dev->mem_start);
 279
 280         ei_status.reset_8390 = &e21_reset_8390;
 281         ei_status.block_input = &e21_block_input;
 282         ei_status.block_output = &e21_block_output;
 283         ei_status.get_8390_hdr = &e21_get_8390_hdr;
 284
 285         dev->netdev_ops = &e21_netdev_ops;
 286         NS8390_init(dev, 0);
 287
 288         retval = register_netdev(dev);
 289         if (retval)
 290                 goto out;
 291         return 0;
 292 out:
 293         release_region(ioaddr, E21_IO_EXTENT);
 294         return retval;
 295 }
 296
 297 static int
 298 e21_open(struct net_device *dev)
 299 {
 300         short ioaddr = dev->base_addr;
 301         int retval;
 302
 303         if ((retval = request_irq(dev->irq, ei_interrupt, 0, dev->name, dev)))
 304                 return retval;
 305
 306         /* Set the interrupt line and memory base on the hardware. */
 307         inb(ioaddr + E21_IRQ_LOW);
 308         outb(0, ioaddr + E21_ASIC + (dev->irq & 7));
 309         inb(ioaddr + E21_IRQ_HIGH);                     /* High IRQ bit, and if_port. */
 310         outb(0, ioaddr + E21_ASIC + (dev->irq > 7 ? 1:0)
 311                    + (dev->if_port ? E21_ALT_IFPORT : 0));
 312         inb(ioaddr + E21_MEM_BASE);
 313         outb(0, ioaddr + E21_ASIC + ((dev->mem_start >> 17) & 7));
 314
 315         ei_open(dev);
 316         return 0;
 317 }
 318
 319 static void
 320 e21_reset_8390(struct net_device *dev)
 321 {
 322         short ioaddr = dev->base_addr;
 323
 324         outb(0x01, ioaddr);
 325         if (ei_debug > 1) printk("resetting the E2180x3 t=%ld...", jiffies);
 326         ei_status.txing = 0;
 327
 328         /* Set up the ASIC registers, just in case something changed them. */
 329
 330         if (ei_debug > 1) printk("reset done\n");
 331         return;
 332 }
 333
 334 /* Grab the 8390 specific header. We put the 2k window so the header page
 335    appears at the start of the shared memory. */
 336
 337 static void
 338 e21_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
 339 {
 340
 341         short ioaddr = dev->base_addr;
 342         char __iomem *shared_mem = ei_status.mem;
 343
 344         mem_on(ioaddr, shared_mem, ring_page);
 345
 346 #ifdef notdef
 347         /* Officially this is what we are doing, but the readl() is faster */
 348         memcpy_fromio(hdr, shared_mem, sizeof(struct e8390_pkt_hdr));
 349 #else
 350         ((unsigned int*)hdr)[0] = readl(shared_mem);
 351 #endif
 352
 353         /* Turn off memory access: we would need to reprogram the window anyway. */
 354         mem_off(ioaddr);
 355
 356 }
 357
 358 /*  Block input and output are easy on shared memory ethercards.
 359         The E21xx makes block_input() especially easy by wrapping the top
 360         ring buffer to the bottom automatically. */
 361 static void
 362 e21_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset)
 363 {
 364         short ioaddr = dev->base_addr;
 365         char __iomem *shared_mem = ei_status.mem;
 366
 367         mem_on(ioaddr, shared_mem, (ring_offset>>8));
 368
 369         memcpy_fromio(skb->data, ei_status.mem + (ring_offset & 0xff), count);
 370
 371         mem_off(ioaddr);
 372 }
 373
 374 static void
 375 e21_block_output(struct net_device *dev, int count, const unsigned char *buf,
 376                                  int start_page)
 377 {
 378         short ioaddr = dev->base_addr;
 379         volatile char __iomem *shared_mem = ei_status.mem;
 380
 381         /* Set the shared memory window start by doing a read, with the low address
 382            bits specifying the starting page. */
 383         readb(shared_mem + start_page);
 384         mem_on(ioaddr, shared_mem, start_page);
 385
 386         memcpy_toio(shared_mem, buf, count);
 387         mem_off(ioaddr);
 388 }
 389
 390 static int
 391 e21_close(struct net_device *dev)
 392 {
 393         short ioaddr = dev->base_addr;
 394
 395         if (ei_debug > 1)
 396                 printk("%s: Shutting down ethercard.\n", dev->name);
 397
 398         free_irq(dev->irq, dev);
 399         dev->irq = ei_status.saved_irq;
 400
 401         /* Shut off the interrupt line and secondary interface. */
 402         inb(ioaddr + E21_IRQ_LOW);
 403         outb(0, ioaddr + E21_ASIC);
 404         inb(ioaddr + E21_IRQ_HIGH);                     /* High IRQ bit, and if_port. */
 405         outb(0, ioaddr + E21_ASIC);
 406
 407         ei_close(dev);
 408
 409         /* Double-check that the memory has been turned off, because really
 410            really bad things happen if it isn't. */
 411         mem_off(ioaddr);
 412
 413         return 0;
 414 }
 415
 416
 417 #ifdef MODULE
 418 #define MAX_E21_CARDS   4       /* Max number of E21 cards per module */
 419 static struct net_device *dev_e21[MAX_E21_CARDS];
 420 static int io[MAX_E21_CARDS];
 421 static int irq[MAX_E21_CARDS];
 422 static int mem[MAX_E21_CARDS];
 423 static int xcvr[MAX_E21_CARDS];         /* choose int. or ext. xcvr */
 424
 425 module_param_array(io, int, NULL, 0);
 426 module_param_array(irq, int, NULL, 0);
 427 module_param_array(mem, int, NULL, 0);
 428 module_param_array(xcvr, int, NULL, 0);
 429 MODULE_PARM_DESC(io, "I/O base address(es)");
 430 MODULE_PARM_DESC(irq, "IRQ number(s)");
 431 MODULE_PARM_DESC(mem, " memory base address(es)");
 432 MODULE_PARM_DESC(xcvr, "transceiver(s) (0=internal, 1=external)");
 433 MODULE_DESCRIPTION("Cabletron E2100 ISA ethernet driver");
 434 MODULE_LICENSE("GPL");
 435
 436 /* This is set up so that only a single autoprobe takes place per call.
 437 ISA device autoprobes on a running machine are not recommended. */
 438
 439 int __init init_module(void)
 440 {
 441         struct net_device *dev;
 442         int this_dev, found = 0;
 443
 444         for (this_dev = 0; this_dev < MAX_E21_CARDS; this_dev++) {
 445                 if (io[this_dev] == 0)  {
 446                         if (this_dev != 0) break; /* only autoprobe 1st one */
 447                         printk(KERN_NOTICE "e2100.c: Presently autoprobing (not recommended) for a single card.\n");
 448                 }
 449                 dev = alloc_ei_netdev();
 450                 if (!dev)
 451                         break;
 452                 dev->irq = irq[this_dev];
 453                 dev->base_addr = io[this_dev];
 454                 dev->mem_start = mem[this_dev];
 455                 dev->mem_end = xcvr[this_dev];  /* low 4bits = xcvr sel. */
 456                 if (do_e2100_probe(dev) == 0) {
 457                         dev_e21[found++] = dev;
 458                         continue;
 459                 }
 460                 free_netdev(dev);
 461                 printk(KERN_WARNING "e2100.c: No E2100 card found (i/o = 0x%x).\n", io[this_dev]);
 462                 break;
 463         }
 464         if (found)
 465                 return 0;
 466         return -ENXIO;
 467 }
 468
 469 static void cleanup_card(struct net_device *dev)
 470 {
 471         /* NB: e21_close() handles free_irq */
 472         iounmap(ei_status.mem);
 473         release_region(dev->base_addr, E21_IO_EXTENT);
 474 }
 475
 476 void __exit
 477 cleanup_module(void)
 478 {
 479         int this_dev;
 480
 481         for (this_dev = 0; this_dev < MAX_E21_CARDS; this_dev++) {
 482                 struct net_device *dev = dev_e21[this_dev];
 483                 if (dev) {
 484                         unregister_netdev(dev);
 485                         cleanup_card(dev);
 486                         free_netdev(dev);
 487                 }
 488         }
 489 }
 490 #endif /* MODULE */