drivers/block/xd.h

   1 #ifndef _LINUX_XD_H
   2 #define _LINUX_XD_H
   3
   4 /*
   5  * This file contains the definitions for the IO ports and errors etc. for XT hard disk controllers (at least the DTC 5150X).
   6  *
   7  * Author: Pat Mackinlay, pat@it.com.au
   8  * Date: 29/09/92
   9  *
  10  * Revised: 01/01/93, ...
  11  *
  12  * Ref: DTC 5150X Controller Specification (thanks to Kevin Fowler, kevinf@agora.rain.com)
  13  * Also thanks to: Salvador Abreu, Dave Thaler, Risto Kankkunen and Wim Van Dorst.
  14  */
  15
  16 /* XT hard disk controller registers */
  17 #define XD_DATA         (xd_iobase + 0x00)      /* data RW register */
  18 #define XD_RESET        (xd_iobase + 0x01)      /* reset WO register */
  19 #define XD_STATUS       (xd_iobase + 0x01)      /* status RO register */
  20 #define XD_SELECT       (xd_iobase + 0x02)      /* select WO register */
  21 #define XD_JUMPER       (xd_iobase + 0x02)      /* jumper RO register */
  22 #define XD_CONTROL      (xd_iobase + 0x03)      /* DMAE/INTE WO register */
  23 #define XD_RESERVED     (xd_iobase + 0x03)      /* reserved */
  24
  25 /* XT hard disk controller commands (incomplete list) */
  26 #define CMD_TESTREADY   0x00    /* test drive ready */
  27 #define CMD_RECALIBRATE 0x01    /* recalibrate drive */
  28 #define CMD_SENSE       0x03    /* request sense */
  29 #define CMD_FORMATDRV   0x04    /* format drive */
  30 #define CMD_VERIFY      0x05    /* read verify */
  31 #define CMD_FORMATTRK   0x06    /* format track */
  32 #define CMD_FORMATBAD   0x07    /* format bad track */
  33 #define CMD_READ        0x08    /* read */
  34 #define CMD_WRITE       0x0A    /* write */
  35 #define CMD_SEEK        0x0B    /* seek */
  36
  37 /* Controller specific commands */
  38 #define CMD_DTCSETPARAM 0x0C    /* set drive parameters (DTC 5150X & CX only?) */
  39 #define CMD_DTCGETECC   0x0D    /* get ecc error length (DTC 5150X only?) */
  40 #define CMD_DTCREADBUF  0x0E    /* read sector buffer (DTC 5150X only?) */
  41 #define CMD_DTCWRITEBUF 0x0F    /* write sector buffer (DTC 5150X only?) */
  42 #define CMD_DTCREMAPTRK 0x11    /* assign alternate track (DTC 5150X only?) */
  43 #define CMD_DTCGETPARAM 0xFB    /* get drive parameters (DTC 5150X only?) */
  44 #define CMD_DTCSETSTEP  0xFC    /* set step rate (DTC 5150X only?) */
  45 #define CMD_DTCSETGEOM  0xFE    /* set geometry data (DTC 5150X only?) */
  46 #define CMD_DTCGETGEOM  0xFF    /* get geometry data (DTC 5150X only?) */
  47 #define CMD_ST11GETGEOM 0xF8    /* get geometry data (Seagate ST11R/M only?) */
  48 #define CMD_WDSETPARAM  0x0C    /* set drive parameters (WD 1004A27X only?) */
  49 #define CMD_XBSETPARAM  0x0C    /* set drive parameters (XEBEC only?) */
  50
  51 /* Bits for command status byte */
  52 #define CSB_ERROR       0x02    /* error */
  53 #define CSB_LUN         0x20    /* logical Unit Number */
  54
  55 /* XT hard disk controller status bits */
  56 #define STAT_READY      0x01    /* controller is ready */
  57 #define STAT_INPUT      0x02    /* data flowing from controller to host */
  58 #define STAT_COMMAND    0x04    /* controller in command phase */
  59 #define STAT_SELECT     0x08    /* controller is selected */
  60 #define STAT_REQUEST    0x10    /* controller requesting data */
  61 #define STAT_INTERRUPT  0x20    /* controller requesting interrupt */
  62
  63 /* XT hard disk controller control bits */
  64 #define PIO_MODE        0x00    /* control bits to set for PIO */
  65 #define DMA_MODE        0x03    /* control bits to set for DMA & interrupt */
  66
  67 #define XD_MAXDRIVES    2       /* maximum 2 drives */
  68 #define XD_TIMEOUT      HZ      /* 1 second timeout */
  69 #define XD_RETRIES      4       /* maximum 4 retries */
  70
  71 #undef DEBUG                    /* define for debugging output */
  72
  73 #ifdef DEBUG
  74         #define DEBUG_STARTUP   /* debug driver initialisation */
  75         #define DEBUG_OVERRIDE  /* debug override geometry detection */
  76         #define DEBUG_READWRITE /* debug each read/write command */
  77         #define DEBUG_OTHER     /* debug misc. interrupt/DMA stuff */
  78         #define DEBUG_COMMAND   /* debug each controller command */
  79 #endif /* DEBUG */
  80
  81 /* this structure defines the XT drives and their types */
  82 typedef struct {
  83         u_char heads;
  84         u_short cylinders;
  85         u_char sectors;
  86         u_char control;
  87 } XD_INFO;
  88
  89 /* this structure is returned to the HDIO_GETGEO ioctl */
  90 typedef struct {
  91         __u8 heads;
  92         __u8 sectors;
  93         __u8 cylinders;
  94         __u32 start;
  95 } XD_GEOMETRY;
  96
  97 /* this structure defines a ROM BIOS signature */
  98 typedef struct {
  99         unsigned int offset;
 100         const char *string;
 101         void (*init_controller)(unsigned int address);
 102         void (*init_drive)(u_char drive);
 103         const char *name;
 104 } XD_SIGNATURE;
 105
 106 static int xd_setup (char *);
 107 #ifndef MODULE
 108 static int xd_manual_geo_init (char *command);
 109 #endif /* MODULE */
 110 static u_char xd_detect (u_char *controller, unsigned int *address);
 111 static u_char xd_initdrives (void (*init_drive)(u_char drive));
 112 static void xd_geninit (void);
 113
 114 static int xd_open (struct inode *inode,struct file *file);
 115 static void do_xd_request (request_queue_t * q);
 116 static int xd_ioctl (struct inode *inode,struct file *file,unsigned int cmd,unsigned long arg);
 117 static int xd_release (struct inode *inode,struct file *file);
 118 static int xd_reread_partitions (kdev_t dev);
 119 static int xd_readwrite (u_char operation,u_char drive,char *buffer,u_int block,u_int count);
 120 static void xd_recalibrate (u_char drive);
 121
 122 static void xd_interrupt_handler (int irq, void *dev_id, struct pt_regs *regs);
 123 static u_char xd_setup_dma (u_char opcode,u_char *buffer,u_int count);
 124 static u_char *xd_build (u_char *cmdblk,u_char command,u_char drive,u_char head,u_short cylinder,u_char sector,u_char count,u_char control);
 125 static void xd_wakeup (unsigned long unused);
 126 static void xd_watchdog (unsigned long unused);
 127 static inline u_char xd_waitport (u_short port,u_char flags,u_char mask,u_long timeout);
 128 static u_int xd_command (u_char *command,u_char mode,u_char *indata,u_char *outdata,u_char *sense,u_long timeout);
 129
 130 /* card specific setup and geometry gathering code */
 131 static void xd_dtc_init_controller (unsigned int address);
 132 static void xd_dtc5150cx_init_drive (u_char drive);
 133 static void xd_dtc_init_drive (u_char drive);
 134 static void xd_wd_init_controller (unsigned int address);
 135 static void xd_wd_init_drive (u_char drive);
 136 static void xd_seagate_init_controller (unsigned int address);
 137 static void xd_seagate_init_drive (u_char drive);
 138 static void xd_omti_init_controller (unsigned int address);
 139 static void xd_omti_init_drive (u_char drive);
 140 static void xd_xebec_init_controller (unsigned int address);
 141 static void xd_xebec_init_drive (u_char drive);
 142 static void xd_setparam (u_char command,u_char drive,u_char heads,u_short cylinders,u_short rwrite,u_short wprecomp,u_char ecc);
 143 static void xd_override_init_drive (u_char drive);
 144
 145 #endif /* _LINUX_XD_H */