include/asm-powerpc/heathrow.h

   1 #ifndef _ASM_POWERPC_HEATHROW_H
   2 #define _ASM_POWERPC_HEATHROW_H
   3 #ifdef __KERNEL__
   4 /*
   5  * heathrow.h: definitions for using the "Heathrow" I/O controller chip.
   6  *
   7  * Grabbed from Open Firmware definitions on a PowerBook G3 Series
   8  *
   9  * Copyright (C) 1997 Paul Mackerras.
  10  */
  11
  12 /* Front light color on Yikes/B&W G3. 32 bits */
  13 #define HEATHROW_FRONT_LIGHT            0x32 /* (set to 0 or 0xffffffff) */
  14
  15 /* Brightness/contrast (gossamer iMac ?). 8 bits */
  16 #define HEATHROW_BRIGHTNESS_CNTL        0x32
  17 #define HEATHROW_CONTRAST_CNTL          0x33
  18
  19 /* offset from ohare base for feature control register */
  20 #define HEATHROW_MBCR                   0x34    /* Media bay control */
  21 #define HEATHROW_FCR                    0x38    /* Feature control */
  22 #define HEATHROW_AUX_CNTL_REG           0x3c    /* Aux control */
  23
  24 /*
  25  * Bits in feature control register.
  26  * Bits postfixed with a _N are in inverse logic
  27  */
  28 #define HRW_SCC_TRANS_EN_N      0x00000001      /* Also controls modem power */
  29 #define HRW_BAY_POWER_N         0x00000002
  30 #define HRW_BAY_PCI_ENABLE      0x00000004
  31 #define HRW_BAY_IDE_ENABLE      0x00000008
  32 #define HRW_BAY_FLOPPY_ENABLE   0x00000010
  33 #define HRW_IDE0_ENABLE         0x00000020
  34 #define HRW_IDE0_RESET_N        0x00000040
  35 #define HRW_BAY_DEV_MASK        0x0000001c
  36 #define HRW_BAY_RESET_N         0x00000080
  37 #define HRW_IOBUS_ENABLE        0x00000100      /* Internal IDE ? */
  38 #define HRW_SCC_ENABLE          0x00000200
  39 #define HRW_MESH_ENABLE         0x00000400
  40 #define HRW_SWIM_ENABLE         0x00000800
  41 #define HRW_SOUND_POWER_N       0x00001000
  42 #define HRW_SOUND_CLK_ENABLE    0x00002000
  43 #define HRW_SCCA_IO             0x00004000
  44 #define HRW_SCCB_IO             0x00008000
  45 #define HRW_PORT_OR_DESK_VIA_N  0x00010000      /* This one is 0 on PowerBook */
  46 #define HRW_PWM_MON_ID_N        0x00020000      /* ??? (0) */
  47 #define HRW_HOOK_MB_CNT_N       0x00040000      /* ??? (0) */
  48 #define HRW_SWIM_CLONE_FLOPPY   0x00080000      /* ??? (0) */
  49 #define HRW_AUD_RUN22           0x00100000      /* ??? (1) */
  50 #define HRW_SCSI_LINK_MODE      0x00200000      /* Read ??? (1) */
  51 #define HRW_ARB_BYPASS          0x00400000      /* Disable internal PCI arbitrer */
  52 #define HRW_IDE1_RESET_N        0x00800000      /* Media bay */
  53 #define HRW_SLOW_SCC_PCLK       0x01000000      /* ??? (0) */
  54 #define HRW_RESET_SCC           0x02000000
  55 #define HRW_MFDC_CELL_ENABLE    0x04000000      /* ??? (0) */
  56 #define HRW_USE_MFDC            0x08000000      /* ??? (0) */
  57 #define HRW_BMAC_IO_ENABLE      0x60000000      /* two bits, not documented in OF */
  58 #define HRW_BMAC_RESET          0x80000000      /* not documented in OF */
  59
  60 /* We OR those features at boot on desktop G3s */
  61 #define HRW_DEFAULTS            (HRW_SCCA_IO | HRW_SCCB_IO | HRW_SCC_ENABLE)
  62
  63 /* Looks like Heathrow has some sort of GPIOs as well... */
  64 #define HRW_GPIO_MODEM_RESET    0x6d
  65
  66 #endif /* __KERNEL__ */
  67 #endif /* _ASM_POWERPC_HEATHROW_H */