drivers/clocksource/tcb_clksrc.c

   1 #include <linux/init.h>
   2 #include <linux/clocksource.h>
   3 #include <linux/clockchips.h>
   4 #include <linux/interrupt.h>
   5 #include <linux/irq.h>
   6
   7 #include <linux/clk.h>
   8 #include <linux/err.h>
   9 #include <linux/ioport.h>
  10 #include <linux/io.h>
  11 #include <linux/platform_device.h>
  12 #include <linux/atmel_tc.h>
  13
  14
  15 /*
  16  * We're configured to use a specific TC block, one that's not hooked
  17  * up to external hardware, to provide a time solution:
  18  *
  19  *   - Two channels combine to create a free-running 32 bit counter
  20  *     with a base rate of 5+ MHz, packaged as a clocksource (with
  21  *     resolution better than 200 nsec).
  22  *
  23  *   - The third channel may be used to provide a 16-bit clockevent
  24  *     source, used in either periodic or oneshot mode.  This runs
  25  *     at 32 KiHZ, and can handle delays of up to two seconds.
  26  *
  27  * A boot clocksource and clockevent source are also currently needed,
  28  * unless the relevant platforms (ARM/AT91, AVR32/AT32) are changed so
  29  * this code can be used when init_timers() is called, well before most
  30  * devices are set up.  (Some low end AT91 parts, which can run uClinux,
  31  * have only the timers in one TC block... they currently don't support
  32  * the tclib code, because of that initialization issue.)
  33  *
  34  * REVISIT behavior during system suspend states... we should disable
  35  * all clocks and save the power.  Easily done for clockevent devices,
  36  * but clocksources won't necessarily get the needed notifications.
  37  * For deeper system sleep states, this will be mandatory...
  38  */
  39
  40 static void __iomem *tcaddr;
  41
  42 static cycle_t tc_get_cycles(void)
  43 {
  44         unsigned long   flags;
  45         u32             lower, upper;
  46
  47         raw_local_irq_save(flags);
  48         do {
  49                 upper = __raw_readl(tcaddr + ATMEL_TC_REG(1, CV));
  50                 lower = __raw_readl(tcaddr + ATMEL_TC_REG(0, CV));
  51         } while (upper != __raw_readl(tcaddr + ATMEL_TC_REG(1, CV)));
  52
  53         raw_local_irq_restore(flags);
  54         return (upper << 16) | lower;
  55 }
  56
  57 static struct clocksource clksrc = {
  58         .name           = "tcb_clksrc",
  59         .rating         = 200,
  60         .read           = tc_get_cycles,
  61         .mask           = CLOCKSOURCE_MASK(32),
  62         .shift          = 18,
  63         .flags          = CLOCK_SOURCE_IS_CONTINUOUS,
  64 };
  65
  66 #ifdef CONFIG_GENERIC_CLOCKEVENTS
  67
  68 struct tc_clkevt_device {
  69         struct clock_event_device       clkevt;
  70         struct clk                      *clk;
  71         void __iomem                    *regs;
  72 };
  73
  74 static struct tc_clkevt_device *to_tc_clkevt(struct clock_event_device *clkevt)
  75 {
  76         return container_of(clkevt, struct tc_clkevt_device, clkevt);
  77 }
  78
  79 /* For now, we always use the 32K clock ... this optimizes for NO_HZ,
  80  * because using one of the divided clocks would usually mean the
  81  * tick rate can never be less than several dozen Hz (vs 0.5 Hz).
  82  *
  83  * A divided clock could be good for high resolution timers, since
  84  * 30.5 usec resolution can seem "low".
  85  */
  86 static u32 timer_clock;
  87
  88 static void tc_mode(enum clock_event_mode m, struct clock_event_device *d)
  89 {
  90         struct tc_clkevt_device *tcd = to_tc_clkevt(d);
  91         void __iomem            *regs = tcd->regs;
  92
  93         if (tcd->clkevt.mode == CLOCK_EVT_MODE_PERIODIC
  94                         || tcd->clkevt.mode == CLOCK_EVT_MODE_ONESHOT) {
  95                 __raw_writel(0xff, regs + ATMEL_TC_REG(2, IDR));
  96                 __raw_writel(ATMEL_TC_CLKDIS, regs + ATMEL_TC_REG(2, CCR));
  97                 clk_disable(tcd->clk);
  98         }
  99
 100         switch (m) {
 101
 102         /* By not making the gentime core emulate periodic mode on top
 103          * of oneshot, we get lower overhead and improved accuracy.
 104          */
 105         case CLOCK_EVT_MODE_PERIODIC:
 106                 clk_enable(tcd->clk);
 107
 108                 /* slow clock, count up to RC, then irq and restart */
 109                 __raw_writel(timer_clock
 110                                 | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO,
 111                                 regs + ATMEL_TC_REG(2, CMR));
 112                 __raw_writel((32768 + HZ/2) / HZ, tcaddr + ATMEL_TC_REG(2, RC));
 113
 114                 /* Enable clock and interrupts on RC compare */
 115                 __raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
 116
 117                 /* go go gadget! */
 118                 __raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
 119                                 regs + ATMEL_TC_REG(2, CCR));
 120                 break;
 121
 122         case CLOCK_EVT_MODE_ONESHOT:
 123                 clk_enable(tcd->clk);
 124
 125                 /* slow clock, count up to RC, then irq and stop */
 126                 __raw_writel(timer_clock | ATMEL_TC_CPCSTOP
 127                                 | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO,
 128                                 regs + ATMEL_TC_REG(2, CMR));
 129                 __raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
 130
 131                 /* set_next_event() configures and starts the timer */
 132                 break;
 133
 134         default:
 135                 break;
 136         }
 137 }
 138
 139 static int tc_next_event(unsigned long delta, struct clock_event_device *d)
 140 {
 141         __raw_writel(delta, tcaddr + ATMEL_TC_REG(2, RC));
 142
 143         /* go go gadget! */
 144         __raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
 145                         tcaddr + ATMEL_TC_REG(2, CCR));
 146         return 0;
 147 }
 148
 149 static struct tc_clkevt_device clkevt = {
 150         .clkevt = {
 151                 .name           = "tc_clkevt",
 152                 .features       = CLOCK_EVT_FEAT_PERIODIC
 153                                         | CLOCK_EVT_FEAT_ONESHOT,
 154                 .shift          = 32,
 155                 /* Should be lower than at91rm9200's system timer */
 156                 .rating         = 125,
 157                 .set_next_event = tc_next_event,
 158                 .set_mode       = tc_mode,
 159         },
 160 };
 161
 162 static irqreturn_t ch2_irq(int irq, void *handle)
 163 {
 164         struct tc_clkevt_device *dev = handle;
 165         unsigned int            sr;
 166
 167         sr = __raw_readl(dev->regs + ATMEL_TC_REG(2, SR));
 168         if (sr & ATMEL_TC_CPCS) {
 169                 dev->clkevt.event_handler(&dev->clkevt);
 170                 return IRQ_HANDLED;
 171         }
 172
 173         return IRQ_NONE;
 174 }
 175
 176 static struct irqaction tc_irqaction = {
 177         .name           = "tc_clkevt",
 178         .flags          = IRQF_TIMER | IRQF_DISABLED,
 179         .handler        = ch2_irq,
 180 };
 181
 182 static void __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
 183 {
 184         struct clk *t2_clk = tc->clk[2];
 185         int irq = tc->irq[2];
 186
 187         clkevt.regs = tc->regs;
 188         clkevt.clk = t2_clk;
 189         tc_irqaction.dev_id = &clkevt;
 190
 191         timer_clock = clk32k_divisor_idx;
 192
 193         clkevt.clkevt.mult = div_sc(32768, NSEC_PER_SEC, clkevt.clkevt.shift);
 194         clkevt.clkevt.max_delta_ns
 195                 = clockevent_delta2ns(0xffff, &clkevt.clkevt);
 196         clkevt.clkevt.min_delta_ns = clockevent_delta2ns(1, &clkevt.clkevt) + 1;
 197         clkevt.clkevt.cpumask = cpumask_of(0);
 198
 199         setup_irq(irq, &tc_irqaction);
 200
 201         clockevents_register_device(&clkevt.clkevt);
 202 }
 203
 204 #else /* !CONFIG_GENERIC_CLOCKEVENTS */
 205
 206 static void __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
 207 {
 208         /* NOTHING */
 209 }
 210
 211 #endif
 212
 213 static int __init tcb_clksrc_init(void)
 214 {
 215         static char bootinfo[] __initdata
 216                 = KERN_DEBUG "%s: tc%d at %d.%03d MHz\n";
 217
 218         struct platform_device *pdev;
 219         struct atmel_tc *tc;
 220         struct clk *t0_clk;
 221         u32 rate, divided_rate = 0;
 222         int best_divisor_idx = -1;
 223         int clk32k_divisor_idx = -1;
 224         int i;
 225
 226         tc = atmel_tc_alloc(CONFIG_ATMEL_TCB_CLKSRC_BLOCK, clksrc.name);
 227         if (!tc) {
 228                 pr_debug("can't alloc TC for clocksource\n");
 229                 return -ENODEV;
 230         }
 231         tcaddr = tc->regs;
 232         pdev = tc->pdev;
 233
 234         t0_clk = tc->clk[0];
 235         clk_enable(t0_clk);
 236
 237         /* How fast will we be counting?  Pick something over 5 MHz.  */
 238         rate = (u32) clk_get_rate(t0_clk);
 239         for (i = 0; i < 5; i++) {
 240                 unsigned divisor = atmel_tc_divisors[i];
 241                 unsigned tmp;
 242
 243                 /* remember 32 KiHz clock for later */
 244                 if (!divisor) {
 245                         clk32k_divisor_idx = i;
 246                         continue;
 247                 }
 248
 249                 tmp = rate / divisor;
 250                 pr_debug("TC: %u / %-3u [%d] --> %u\n", rate, divisor, i, tmp);
 251                 if (best_divisor_idx > 0) {
 252                         if (tmp < 5 * 1000 * 1000)
 253                                 continue;
 254                 }
 255                 divided_rate = tmp;
 256                 best_divisor_idx = i;
 257         }
 258
 259         clksrc.mult = clocksource_hz2mult(divided_rate, clksrc.shift);
 260
 261         printk(bootinfo, clksrc.name, CONFIG_ATMEL_TCB_CLKSRC_BLOCK,
 262                         divided_rate / 1000000,
 263                         ((divided_rate + 500000) % 1000000) / 1000);
 264
 265         /* tclib will give us three clocks no matter what the
 266          * underlying platform supports.
 267          */
 268         clk_enable(tc->clk[1]);
 269
 270         /* channel 0:  waveform mode, input mclk/8, clock TIOA0 on overflow */
 271         __raw_writel(best_divisor_idx                   /* likely divide-by-8 */
 272                         | ATMEL_TC_WAVE
 273                         | ATMEL_TC_WAVESEL_UP           /* free-run */
 274                         | ATMEL_TC_ACPA_SET             /* TIOA0 rises at 0 */
 275                         | ATMEL_TC_ACPC_CLEAR,          /* (duty cycle 50%) */
 276                         tcaddr + ATMEL_TC_REG(0, CMR));
 277         __raw_writel(0x0000, tcaddr + ATMEL_TC_REG(0, RA));
 278         __raw_writel(0x8000, tcaddr + ATMEL_TC_REG(0, RC));
 279         __raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR));      /* no irqs */
 280         __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
 281
 282         /* channel 1:  waveform mode, input TIOA0 */
 283         __raw_writel(ATMEL_TC_XC1                       /* input: TIOA0 */
 284                         | ATMEL_TC_WAVE
 285                         | ATMEL_TC_WAVESEL_UP,          /* free-run */
 286                         tcaddr + ATMEL_TC_REG(1, CMR));
 287         __raw_writel(0xff, tcaddr + ATMEL_TC_REG(1, IDR));      /* no irqs */
 288         __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(1, CCR));
 289
 290         /* chain channel 0 to channel 1, then reset all the timers */
 291         __raw_writel(ATMEL_TC_TC1XC1S_TIOA0, tcaddr + ATMEL_TC_BMR);
 292         __raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
 293
 294         /* and away we go! */
 295         clocksource_register(&clksrc);
 296
 297         /* channel 2:  periodic and oneshot timer support */
 298         setup_clkevents(tc, clk32k_divisor_idx);
 299
 300         return 0;
 301 }
 302 arch_initcall(tcb_clksrc_init);