drivers/parisc/superio.c

   1 /*      National Semiconductor NS87560UBD Super I/O controller used in
   2  *      HP [BCJ]x000 workstations.
   3  *
   4  *      This chip is a horrid piece of engineering, and National
   5  *      denies any knowledge of its existence. Thus no datasheet is
   6  *      available off www.national.com.
   7  *
   8  *      (C) Copyright 2000 Linuxcare, Inc.
   9  *      (C) Copyright 2000 Linuxcare Canada, Inc.
  10  *      (C) Copyright 2000 Martin K. Petersen <mkp@linuxcare.com>
  11  *      (C) Copyright 2000 Alex deVries <alex@onefishtwo.ca>
  12  *      (C) Copyright 2001 John Marvin <jsm fc hp com>
  13  *      (C) Copyright 2003 Grant Grundler <grundler parisc-linux org>
  14  *      (C) Copyright 2005 Kyle McMartin <kyle@parisc-linux.org>
  15  *
  16  *      This program is free software; you can redistribute it and/or
  17  *      modify it under the terms of the GNU General Public License as
  18  *      published by the Free Software Foundation; either version 2 of
  19  *      the License, or (at your option) any later version.
  20  *
  21  *      The initial version of this is by Martin Peterson.  Alex deVries
  22  *      has spent a bit of time trying to coax it into working.
  23  *
  24  *      Major changes to get basic interrupt infrastructure working to
  25  *      hopefully be able to support all SuperIO devices. Currently
  26  *      works with serial. -- John Marvin <jsm@fc.hp.com>
  27  *
  28  *      Converted superio_init() to be a PCI_FIXUP_FINAL callee.
  29  *         -- Kyle McMartin <kyle@parisc-linux.org>
  30  */
  31
  32
  33 /* NOTES:
  34  *
  35  * Function 0 is an IDE controller. It is identical to a PC87415 IDE
  36  * controller (and identifies itself as such).
  37  *
  38  * Function 1 is a "Legacy I/O" controller. Under this function is a
  39  * whole mess of legacy I/O peripherals. Of course, HP hasn't enabled
  40  * all the functionality in hardware, but the following is available:
  41  *
  42  *      Two 16550A compatible serial controllers
  43  *      An IEEE 1284 compatible parallel port
  44  *      A floppy disk controller
  45  *
  46  * Function 2 is a USB controller.
  47  *
  48  * We must be incredibly careful during initialization.  Since all
  49  * interrupts are routed through function 1 (which is not allowed by
  50  * the PCI spec), we need to program the PICs on the legacy I/O port
  51  * *before* we attempt to set up IDE and USB.  @#$!&
  52  *
  53  * According to HP, devices are only enabled by firmware if they have
  54  * a physical device connected.
  55  *
  56  * Configuration register bits:
  57  *     0x5A: FDC, SP1, IDE1, SP2, IDE2, PAR, Reserved, P92
  58  *     0x5B: RTC, 8259, 8254, DMA1, DMA2, KBC, P61, APM
  59  *
  60  */
  61
  62 #include <linux/errno.h>
  63 #include <linux/init.h>
  64 #include <linux/module.h>
  65 #include <linux/types.h>
  66 #include <linux/interrupt.h>
  67 #include <linux/ioport.h>
  68 #include <linux/serial.h>
  69 #include <linux/pci.h>
  70 #include <linux/parport.h>
  71 #include <linux/parport_pc.h>
  72 #include <linux/termios.h>
  73 #include <linux/tty.h>
  74 #include <linux/serial_core.h>
  75 #include <linux/delay.h>
  76
  77 #include <asm/io.h>
  78 #include <asm/hardware.h>
  79 #include <asm/superio.h>
  80
  81 static struct superio_device sio_dev;
  82
  83
  84 #undef DEBUG_SUPERIO_INIT
  85
  86 #ifdef DEBUG_SUPERIO_INIT
  87 #define DBG_INIT(x...)  printk(x)
  88 #else
  89 #define DBG_INIT(x...)
  90 #endif
  91
  92 #define SUPERIO "SuperIO"
  93 #define PFX     SUPERIO ": "
  94
  95 static irqreturn_t
  96 superio_interrupt(int parent_irq, void *devp, struct pt_regs *regs)
  97 {
  98         u8 results;
  99         u8 local_irq;
 100
 101         /* Poll the 8259 to see if there's an interrupt. */
 102         outb (OCW3_POLL,IC_PIC1+0);
 103
 104         results = inb(IC_PIC1+0);
 105
 106         /*
 107          * Bit    7:    1 = active Interrupt; 0 = no Interrupt pending
 108          * Bits 6-3:    zero
 109          * Bits 2-0:    highest priority, active requesting interrupt ID (0-7)
 110          */
 111         if ((results & 0x80) == 0) {
 112                 /* I suspect "spurious" interrupts are from unmasking an IRQ.
 113                  * We don't know if an interrupt was/is pending and thus
 114                  * just call the handler for that IRQ as if it were pending.
 115                  */
 116                 return IRQ_NONE;
 117         }
 118
 119         /* Check to see which device is interrupting */
 120         local_irq = results & 0x0f;
 121
 122         if (local_irq == 2 || local_irq > 7) {
 123                 printk(KERN_ERR PFX "slave interrupted!\n");
 124                 return IRQ_HANDLED;
 125         }
 126
 127         if (local_irq == 7) {
 128
 129                 /* Could be spurious. Check in service bits */
 130
 131                 outb(OCW3_ISR,IC_PIC1+0);
 132                 results = inb(IC_PIC1+0);
 133                 if ((results & 0x80) == 0) { /* if ISR7 not set: spurious */
 134                         printk(KERN_WARNING PFX "spurious interrupt!\n");
 135                         return IRQ_HANDLED;
 136                 }
 137         }
 138
 139         /* Call the appropriate device's interrupt */
 140         __do_IRQ(local_irq, regs);
 141
 142         /* set EOI - forces a new interrupt if a lower priority device
 143          * still needs service.
 144          */
 145         outb((OCW2_SEOI|local_irq),IC_PIC1 + 0);
 146         return IRQ_HANDLED;
 147 }
 148
 149 /* Initialize Super I/O device */
 150 static void
 151 superio_init(struct pci_dev *pcidev)
 152 {
 153         struct superio_device *sio = &sio_dev;
 154         struct pci_dev *pdev = sio->lio_pdev;
 155         u16 word;
 156
 157         if (sio->suckyio_irq_enabled)
 158                 return;
 159
 160         if (!pdev) BUG();
 161         if (!sio->usb_pdev) BUG();
 162
 163         /* use the IRQ iosapic found for USB INT D... */
 164         pdev->irq = sio->usb_pdev->irq;
 165
 166         /* ...then properly fixup the USB to point at suckyio PIC */
 167         sio->usb_pdev->irq = superio_fixup_irq(sio->usb_pdev);
 168
 169         printk(KERN_INFO PFX "Found NS87560 Legacy I/O device at %s (IRQ %i) \n",
 170                pci_name(pdev), pdev->irq);
 171
 172         pci_read_config_dword (pdev, SIO_SP1BAR, &sio->sp1_base);
 173         sio->sp1_base &= ~1;
 174         printk(KERN_INFO PFX "Serial port 1 at 0x%x\n", sio->sp1_base);
 175
 176         pci_read_config_dword (pdev, SIO_SP2BAR, &sio->sp2_base);
 177         sio->sp2_base &= ~1;
 178         printk(KERN_INFO PFX "Serial port 2 at 0x%x\n", sio->sp2_base);
 179
 180         pci_read_config_dword (pdev, SIO_PPBAR, &sio->pp_base);
 181         sio->pp_base &= ~1;
 182         printk(KERN_INFO PFX "Parallel port at 0x%x\n", sio->pp_base);
 183
 184         pci_read_config_dword (pdev, SIO_FDCBAR, &sio->fdc_base);
 185         sio->fdc_base &= ~1;
 186         printk(KERN_INFO PFX "Floppy controller at 0x%x\n", sio->fdc_base);
 187         pci_read_config_dword (pdev, SIO_ACPIBAR, &sio->acpi_base);
 188         sio->acpi_base &= ~1;
 189         printk(KERN_INFO PFX "ACPI at 0x%x\n", sio->acpi_base);
 190
 191         request_region (IC_PIC1, 0x1f, "pic1");
 192         request_region (IC_PIC2, 0x1f, "pic2");
 193         request_region (sio->acpi_base, 0x1f, "acpi");
 194
 195         /* Enable the legacy I/O function */
 196         pci_read_config_word (pdev, PCI_COMMAND, &word);
 197         word |= PCI_COMMAND_SERR | PCI_COMMAND_PARITY | PCI_COMMAND_IO;
 198         pci_write_config_word (pdev, PCI_COMMAND, word);
 199
 200         pci_set_master (pdev);
 201         pci_enable_device(pdev);
 202
 203         /*
 204          * Next project is programming the onboard interrupt controllers.
 205          * PDC hasn't done this for us, since it's using polled I/O.
 206          *
 207          * XXX Use dword writes to avoid bugs in Elroy or Suckyio Config
 208          *     space access.  PCI is by nature a 32-bit bus and config
 209          *     space can be sensitive to that.
 210          */
 211
 212         /* 0x64 - 0x67 :
 213                 DMA Rtg 2
 214                 DMA Rtg 3
 215                 DMA Chan Ctl
 216                 TRIGGER_1    == 0x82   USB & IDE level triggered, rest to edge
 217         */
 218         pci_write_config_dword (pdev, 0x64,         0x82000000U);
 219
 220         /* 0x68 - 0x6b :
 221                 TRIGGER_2    == 0x00   all edge triggered (not used)
 222                 CFG_IR_SER   == 0x43   SerPort1 = IRQ3, SerPort2 = IRQ4
 223                 CFG_IR_PF    == 0x65   ParPort  = IRQ5, FloppyCtlr = IRQ6
 224                 CFG_IR_IDE   == 0x07   IDE1 = IRQ7, reserved
 225         */
 226         pci_write_config_dword (pdev, TRIGGER_2,    0x07654300U);
 227
 228         /* 0x6c - 0x6f :
 229                 CFG_IR_INTAB == 0x00
 230                 CFG_IR_INTCD == 0x10   USB = IRQ1
 231                 CFG_IR_PS2   == 0x00
 232                 CFG_IR_FXBUS == 0x00
 233         */
 234         pci_write_config_dword (pdev, CFG_IR_INTAB, 0x00001000U);
 235
 236         /* 0x70 - 0x73 :
 237                 CFG_IR_USB   == 0x00  not used. USB is connected to INTD.
 238                 CFG_IR_ACPI  == 0x00  not used.
 239                 DMA Priority == 0x4c88  Power on default value. NFC.
 240         */
 241         pci_write_config_dword (pdev, CFG_IR_USB, 0x4c880000U);
 242
 243         /* PIC1 Initialization Command Word register programming */
 244         outb (0x11,IC_PIC1+0);  /* ICW1: ICW4 write req | ICW1 */
 245         outb (0x00,IC_PIC1+1);  /* ICW2: interrupt vector table - not used */
 246         outb (0x04,IC_PIC1+1);  /* ICW3: Cascade */
 247         outb (0x01,IC_PIC1+1);  /* ICW4: x86 mode */
 248
 249         /* PIC1 Program Operational Control Words */
 250         outb (0xff,IC_PIC1+1);  /* OCW1: Mask all interrupts */
 251         outb (0xc2,IC_PIC1+0);  /* OCW2: priority (3-7,0-2) */
 252
 253         /* PIC2 Initialization Command Word register programming */
 254         outb (0x11,IC_PIC2+0);  /* ICW1: ICW4 write req | ICW1 */
 255         outb (0x00,IC_PIC2+1);  /* ICW2: N/A */
 256         outb (0x02,IC_PIC2+1);  /* ICW3: Slave ID code */
 257         outb (0x01,IC_PIC2+1);  /* ICW4: x86 mode */
 258
 259         /* Program Operational Control Words */
 260         outb (0xff,IC_PIC1+1);  /* OCW1: Mask all interrupts */
 261         outb (0x68,IC_PIC1+0);  /* OCW3: OCW3 select | ESMM | SMM */
 262
 263         /* Write master mask reg */
 264         outb (0xff,IC_PIC1+1);
 265
 266         /* Setup USB power regulation */
 267         outb(1, sio->acpi_base + USB_REG_CR);
 268         if (inb(sio->acpi_base + USB_REG_CR) & 1)
 269                 printk(KERN_INFO PFX "USB regulator enabled\n");
 270         else
 271                 printk(KERN_ERR PFX "USB regulator not initialized!\n");
 272
 273         if (request_irq(pdev->irq, superio_interrupt, SA_INTERRUPT,
 274                         SUPERIO, (void *)sio)) {
 275
 276                 printk(KERN_ERR PFX "could not get irq\n");
 277                 BUG();
 278                 return;
 279         }
 280
 281         sio->suckyio_irq_enabled = 1;
 282 }
 283 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_LIO, superio_init);
 284
 285 static void superio_disable_irq(unsigned int irq)
 286 {
 287         u8 r8;
 288
 289         if ((irq < 1) || (irq == 2) || (irq > 7)) {
 290                 printk(KERN_ERR PFX "Illegal irq number.\n");
 291                 BUG();
 292                 return;
 293         }
 294
 295         /* Mask interrupt */
 296
 297         r8 = inb(IC_PIC1+1);
 298         r8 |= (1 << irq);
 299         outb (r8,IC_PIC1+1);
 300 }
 301
 302 static void superio_enable_irq(unsigned int irq)
 303 {
 304         u8 r8;
 305
 306         if ((irq < 1) || (irq == 2) || (irq > 7)) {
 307                 printk(KERN_ERR PFX "Illegal irq number (%d).\n", irq);
 308                 BUG();
 309                 return;
 310         }
 311
 312         /* Unmask interrupt */
 313         r8 = inb(IC_PIC1+1);
 314         r8 &= ~(1 << irq);
 315         outb (r8,IC_PIC1+1);
 316 }
 317
 318 static unsigned int superio_startup_irq(unsigned int irq)
 319 {
 320         superio_enable_irq(irq);
 321         return 0;
 322 }
 323
 324 static struct hw_interrupt_type superio_interrupt_type = {
 325         .typename =     SUPERIO,
 326         .startup =      superio_startup_irq,
 327         .shutdown =     superio_disable_irq,
 328         .enable =       superio_enable_irq,
 329         .disable =      superio_disable_irq,
 330         .ack =          no_ack_irq,
 331         .end =          no_end_irq,
 332 };
 333
 334 #ifdef DEBUG_SUPERIO_INIT
 335 static unsigned short expected_device[3] = {
 336         PCI_DEVICE_ID_NS_87415,
 337         PCI_DEVICE_ID_NS_87560_LIO,
 338         PCI_DEVICE_ID_NS_87560_USB
 339 };
 340 #endif
 341
 342 int superio_fixup_irq(struct pci_dev *pcidev)
 343 {
 344         int local_irq, i;
 345
 346 #ifdef DEBUG_SUPERIO_INIT
 347         int fn;
 348         fn = PCI_FUNC(pcidev->devfn);
 349
 350         /* Verify the function number matches the expected device id. */
 351         if (expected_device[fn] != pcidev->device) {
 352                 BUG();
 353                 return -1;
 354         }
 355         printk("superio_fixup_irq(%s) ven 0x%x dev 0x%x from %p\n",
 356                 pci_name(pcidev),
 357                 pcidev->vendor, pcidev->device,
 358                 __builtin_return_address(0));
 359 #endif
 360
 361         for (i = 0; i < 16; i++) {
 362                 irq_desc[i].handler = &superio_interrupt_type;
 363         }
 364
 365         /*
 366          * We don't allocate a SuperIO irq for the legacy IO function,
 367          * since it is a "bridge". Instead, we will allocate irq's for
 368          * each legacy device as they are initialized.
 369          */
 370
 371         switch(pcidev->device) {
 372         case PCI_DEVICE_ID_NS_87415:            /* Function 0 */
 373                 local_irq = IDE_IRQ;
 374                 break;
 375         case PCI_DEVICE_ID_NS_87560_LIO:        /* Function 1 */
 376                 sio_dev.lio_pdev = pcidev;      /* save for superio_init() */
 377                 return -1;
 378         case PCI_DEVICE_ID_NS_87560_USB:        /* Function 2 */
 379                 sio_dev.usb_pdev = pcidev;      /* save for superio_init() */
 380                 local_irq = USB_IRQ;
 381                 break;
 382         default:
 383                 local_irq = -1;
 384                 BUG();
 385                 break;
 386         }
 387
 388         return local_irq;
 389 }
 390
 391 static struct uart_port serial[] = {
 392         {
 393                 .iotype         = UPIO_PORT,
 394                 .line           = 0,
 395                 .type           = PORT_16550A,
 396                 .uartclk        = 115200*16,
 397                 .fifosize       = 16,
 398         },
 399         {
 400                 .iotype         = UPIO_PORT,
 401                 .line           = 1,
 402                 .type           = PORT_16550A,
 403                 .uartclk        = 115200*16,
 404                 .fifosize       = 16,
 405         }
 406 };
 407
 408 static void __devinit superio_serial_init(void)
 409 {
 410 #ifdef CONFIG_SERIAL_8250
 411         int retval;
 412
 413         serial[0].iobase = sio_dev.sp1_base;
 414         serial[0].irq = SP1_IRQ;
 415         spin_lock_init(&serial[0].lock);
 416
 417         retval = early_serial_setup(&serial[0]);
 418         if (retval < 0) {
 419                 printk(KERN_WARNING PFX "Register Serial #0 failed.\n");
 420                 return;
 421         }
 422
 423         serial[1].iobase = sio_dev.sp2_base;
 424         serial[1].irq = SP2_IRQ;
 425         spin_lock_init(&serial[1].lock);
 426         retval = early_serial_setup(&serial[1]);
 427
 428         if (retval < 0)
 429                 printk(KERN_WARNING PFX "Register Serial #1 failed.\n");
 430 #endif /* CONFIG_SERIAL_8250 */
 431 }
 432
 433
 434 static void __devinit superio_parport_init(void)
 435 {
 436 #ifdef CONFIG_PARPORT_PC
 437         if (!parport_pc_probe_port(sio_dev.pp_base,
 438                         0 /*base_hi*/,
 439                         PAR_IRQ,
 440                         PARPORT_DMA_NONE /* dma */,
 441                         NULL /*struct pci_dev* */) )
 442
 443                 printk(KERN_WARNING PFX "Probing parallel port failed.\n");
 444 #endif  /* CONFIG_PARPORT_PC */
 445 }
 446
 447
 448 static void superio_fixup_pci(struct pci_dev *pdev)
 449 {
 450         u8 prog;
 451
 452         pdev->class |= 0x5;
 453         pci_write_config_byte(pdev, PCI_CLASS_PROG, pdev->class);
 454
 455         pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
 456         printk("PCI: Enabled native mode for NS87415 (pif=0x%x)\n", prog);
 457 }
 458 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415, superio_fixup_pci);
 459
 460
 461 static int __devinit
 462 superio_probe(struct pci_dev *dev, const struct pci_device_id *id)
 463 {
 464         struct superio_device *sio = &sio_dev;
 465
 466         /*
 467         ** superio_probe(00:0e.0) ven 0x100b dev 0x2 sv 0x0 sd 0x0 class 0x1018a
 468         ** superio_probe(00:0e.1) ven 0x100b dev 0xe sv 0x0 sd 0x0 class 0x68000
 469         ** superio_probe(00:0e.2) ven 0x100b dev 0x12 sv 0x0 sd 0x0 class 0xc0310
 470         */
 471         DBG_INIT("superio_probe(%s) ven 0x%x dev 0x%x sv 0x%x sd 0x%x class 0x%x\n",
 472                 pci_name(dev),
 473                 dev->vendor, dev->device,
 474                 dev->subsystem_vendor, dev->subsystem_device,
 475                 dev->class);
 476
 477         if (!sio->suckyio_irq_enabled)
 478                 BUG(); /* Enabled by PCI_FIXUP_FINAL */
 479
 480         if (dev->device == PCI_DEVICE_ID_NS_87560_LIO) {        /* Function 1 */
 481                 superio_parport_init();
 482                 superio_serial_init();
 483                 /* REVISIT XXX : superio_fdc_init() ? */
 484                 return 0;
 485         } else if (dev->device == PCI_DEVICE_ID_NS_87415) {     /* Function 0 */
 486                 DBG_INIT("superio_probe: ignoring IDE 87415\n");
 487         } else if (dev->device == PCI_DEVICE_ID_NS_87560_USB) { /* Function 2 */
 488                 DBG_INIT("superio_probe: ignoring USB OHCI controller\n");
 489         } else {
 490                 DBG_INIT("superio_probe: WTF? Fire Extinguisher?\n");
 491         }
 492
 493         /* Let appropriate other driver claim this device. */
 494         return -ENODEV;
 495 }
 496
 497 static struct pci_device_id superio_tbl[] = {
 498         { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_LIO) },
 499         { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_USB) },
 500         { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415) },
 501         { 0, }
 502 };
 503
 504 static struct pci_driver superio_driver = {
 505         .name =         SUPERIO,
 506         .id_table =     superio_tbl,
 507         .probe =        superio_probe,
 508 };
 509
 510 static int __init superio_modinit(void)
 511 {
 512         return pci_register_driver(&superio_driver);
 513 }
 514
 515 static void __exit superio_exit(void)
 516 {
 517         pci_unregister_driver(&superio_driver);
 518 }
 519
 520 module_init(superio_modinit);
 521 module_exit(superio_exit);