staging: gma500: gtt based hardware scrolling console
[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / drivers / ata / pata_cs5520.c
blob9ddcddc66a20797377c8d1e027ba6c28eb580062
1 /*
2 * IDE tuning and bus mastering support for the CS5510/CS5520
3 * chipsets
5 * The CS5510/CS5520 are slightly unusual devices. Unlike the
6 * typical IDE controllers they do bus mastering with the drive in
7 * PIO mode and smarter silicon.
9 * The practical upshot of this is that we must always tune the
10 * drive for the right PIO mode. We must also ignore all the blacklists
11 * and the drive bus mastering DMA information. Also to confuse matters
12 * further we can do DMA on PIO only drives.
14 * DMA on the 5510 also requires we disable_hlt() during DMA on early
15 * revisions.
17 * *** This driver is strictly experimental ***
19 * (c) Copyright Red Hat Inc 2002
21 * This program is free software; you can redistribute it and/or modify it
22 * under the terms of the GNU General Public License as published by the
23 * Free Software Foundation; either version 2, or (at your option) any
24 * later version.
26 * This program is distributed in the hope that it will be useful, but
27 * WITHOUT ANY WARRANTY; without even the implied warranty of
28 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
29 * General Public License for more details.
31 * Documentation:
32 * Not publicly available.
34 #include <linux/kernel.h>
35 #include <linux/module.h>
36 #include <linux/pci.h>
37 #include <linux/init.h>
38 #include <linux/blkdev.h>
39 #include <linux/delay.h>
40 #include <scsi/scsi_host.h>
41 #include <linux/libata.h>
43 #define DRV_NAME "pata_cs5520"
44 #define DRV_VERSION "0.6.6"
46 struct pio_clocks
48 int address;
49 int assert;
50 int recovery;
53 static const struct pio_clocks cs5520_pio_clocks[]={
54 {3, 6, 11},
55 {2, 5, 6},
56 {1, 4, 3},
57 {1, 3, 2},
58 {1, 2, 1}
61 /**
62 * cs5520_set_timings - program PIO timings
63 * @ap: ATA port
64 * @adev: ATA device
66 * Program the PIO mode timings for the controller according to the pio
67 * clocking table.
70 static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio)
72 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
73 int slave = adev->devno;
75 pio -= XFER_PIO_0;
77 /* Channel command timing */
78 pci_write_config_byte(pdev, 0x62 + ap->port_no,
79 (cs5520_pio_clocks[pio].recovery << 4) |
80 (cs5520_pio_clocks[pio].assert));
81 /* FIXME: should these use address ? */
82 /* Read command timing */
83 pci_write_config_byte(pdev, 0x64 + 4*ap->port_no + slave,
84 (cs5520_pio_clocks[pio].recovery << 4) |
85 (cs5520_pio_clocks[pio].assert));
86 /* Write command timing */
87 pci_write_config_byte(pdev, 0x66 + 4*ap->port_no + slave,
88 (cs5520_pio_clocks[pio].recovery << 4) |
89 (cs5520_pio_clocks[pio].assert));
92 /**
93 * cs5520_set_piomode - program PIO timings
94 * @ap: ATA port
95 * @adev: ATA device
97 * Program the PIO mode timings for the controller according to the pio
98 * clocking table.
101 static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev)
103 cs5520_set_timings(ap, adev, adev->pio_mode);
106 static struct scsi_host_template cs5520_sht = {
107 ATA_BMDMA_SHT(DRV_NAME),
108 .sg_tablesize = LIBATA_DUMB_MAX_PRD,
111 static struct ata_port_operations cs5520_port_ops = {
112 .inherits = &ata_bmdma_port_ops,
113 .qc_prep = ata_bmdma_dumb_qc_prep,
114 .cable_detect = ata_cable_40wire,
115 .set_piomode = cs5520_set_piomode,
118 static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
120 static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
121 static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
122 struct ata_port_info pi = {
123 .flags = ATA_FLAG_SLAVE_POSS,
124 .pio_mask = ATA_PIO4,
125 .port_ops = &cs5520_port_ops,
127 const struct ata_port_info *ppi[2];
128 u8 pcicfg;
129 void __iomem *iomap[5];
130 struct ata_host *host;
131 struct ata_ioports *ioaddr;
132 int i, rc;
134 rc = pcim_enable_device(pdev);
135 if (rc)
136 return rc;
138 /* IDE port enable bits */
139 pci_read_config_byte(pdev, 0x60, &pcicfg);
141 /* Check if the ATA ports are enabled */
142 if ((pcicfg & 3) == 0)
143 return -ENODEV;
145 ppi[0] = ppi[1] = &ata_dummy_port_info;
146 if (pcicfg & 1)
147 ppi[0] = &pi;
148 if (pcicfg & 2)
149 ppi[1] = &pi;
151 if ((pcicfg & 0x40) == 0) {
152 dev_warn(&pdev->dev, "DMA mode disabled. Enabling.\n");
153 pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
156 pi.mwdma_mask = id->driver_data;
158 host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
159 if (!host)
160 return -ENOMEM;
162 /* Perform set up for DMA */
163 if (pci_enable_device_io(pdev)) {
164 printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
165 return -ENODEV;
168 if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
169 printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
170 return -ENODEV;
172 if (pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32))) {
173 printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
174 return -ENODEV;
177 /* Map IO ports and initialize host accordingly */
178 iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
179 iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
180 iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
181 iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
182 iomap[4] = pcim_iomap(pdev, 2, 0);
184 if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
185 return -ENOMEM;
187 ioaddr = &host->ports[0]->ioaddr;
188 ioaddr->cmd_addr = iomap[0];
189 ioaddr->ctl_addr = iomap[1];
190 ioaddr->altstatus_addr = iomap[1];
191 ioaddr->bmdma_addr = iomap[4];
192 ata_sff_std_ports(ioaddr);
194 ata_port_desc(host->ports[0],
195 "cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
196 ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
198 ioaddr = &host->ports[1]->ioaddr;
199 ioaddr->cmd_addr = iomap[2];
200 ioaddr->ctl_addr = iomap[3];
201 ioaddr->altstatus_addr = iomap[3];
202 ioaddr->bmdma_addr = iomap[4] + 8;
203 ata_sff_std_ports(ioaddr);
205 ata_port_desc(host->ports[1],
206 "cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
207 ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
209 /* activate the host */
210 pci_set_master(pdev);
211 rc = ata_host_start(host);
212 if (rc)
213 return rc;
215 for (i = 0; i < 2; i++) {
216 static const int irq[] = { 14, 15 };
217 struct ata_port *ap = host->ports[i];
219 if (ata_port_is_dummy(ap))
220 continue;
222 rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
223 ata_bmdma_interrupt, 0, DRV_NAME, host);
224 if (rc)
225 return rc;
227 ata_port_desc(ap, "irq %d", irq[i]);
230 return ata_host_register(host, &cs5520_sht);
233 #ifdef CONFIG_PM
235 * cs5520_reinit_one - device resume
236 * @pdev: PCI device
238 * Do any reconfiguration work needed by a resume from RAM. We need
239 * to restore DMA mode support on BIOSen which disabled it
242 static int cs5520_reinit_one(struct pci_dev *pdev)
244 struct ata_host *host = dev_get_drvdata(&pdev->dev);
245 u8 pcicfg;
246 int rc;
248 rc = ata_pci_device_do_resume(pdev);
249 if (rc)
250 return rc;
252 pci_read_config_byte(pdev, 0x60, &pcicfg);
253 if ((pcicfg & 0x40) == 0)
254 pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
256 ata_host_resume(host);
257 return 0;
261 * cs5520_pci_device_suspend - device suspend
262 * @pdev: PCI device
264 * We have to cut and waste bits from the standard method because
265 * the 5520 is a bit odd and not just a pure ATA device. As a result
266 * we must not disable it. The needed code is short and this avoids
267 * chip specific mess in the core code.
270 static int cs5520_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
272 struct ata_host *host = dev_get_drvdata(&pdev->dev);
273 int rc = 0;
275 rc = ata_host_suspend(host, mesg);
276 if (rc)
277 return rc;
279 pci_save_state(pdev);
280 return 0;
282 #endif /* CONFIG_PM */
284 /* For now keep DMA off. We can set it for all but A rev CS5510 once the
285 core ATA code can handle it */
287 static const struct pci_device_id pata_cs5520[] = {
288 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
289 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
291 { },
294 static struct pci_driver cs5520_pci_driver = {
295 .name = DRV_NAME,
296 .id_table = pata_cs5520,
297 .probe = cs5520_init_one,
298 .remove = ata_pci_remove_one,
299 #ifdef CONFIG_PM
300 .suspend = cs5520_pci_device_suspend,
301 .resume = cs5520_reinit_one,
302 #endif
305 static int __init cs5520_init(void)
307 return pci_register_driver(&cs5520_pci_driver);
310 static void __exit cs5520_exit(void)
312 pci_unregister_driver(&cs5520_pci_driver);
315 MODULE_AUTHOR("Alan Cox");
316 MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520");
317 MODULE_LICENSE("GPL");
318 MODULE_DEVICE_TABLE(pci, pata_cs5520);
319 MODULE_VERSION(DRV_VERSION);
321 module_init(cs5520_init);
322 module_exit(cs5520_exit);