arch/arm/mach-ixp4xx/ixdp425-setup.c

   1 /*
   2  * arch/arm/mach-ixp4xx/ixdp425-setup.c
   3  *
   4  * IXDP425/IXCDP1100 board-setup
   5  *
   6  * Copyright (C) 2003-2005 MontaVista Software, Inc.
   7  *
   8  * Author: Deepak Saxena <dsaxena@plexity.net>
   9  */
  10
  11 #include <linux/kernel.h>
  12 #include <linux/init.h>
  13 #include <linux/device.h>
  14 #include <linux/serial.h>
  15 #include <linux/tty.h>
  16 #include <linux/serial_8250.h>
  17 #include <linux/i2c-gpio.h>
  18 #include <linux/io.h>
  19 #include <linux/mtd/mtd.h>
  20 #include <linux/mtd/nand.h>
  21 #include <linux/mtd/partitions.h>
  22 #include <linux/delay.h>
  23 #include <asm/types.h>
  24 #include <asm/setup.h>
  25 #include <asm/memory.h>
  26 #include <mach/hardware.h>
  27 #include <asm/mach-types.h>
  28 #include <asm/irq.h>
  29 #include <asm/mach/arch.h>
  30 #include <asm/mach/flash.h>
  31
  32 #define IXDP425_SDA_PIN         7
  33 #define IXDP425_SCL_PIN         6
  34
  35 /* NAND Flash pins */
  36 #define IXDP425_NAND_NCE_PIN    12
  37
  38 #define IXDP425_NAND_CMD_BYTE   0x01
  39 #define IXDP425_NAND_ADDR_BYTE  0x02
  40
  41 static struct flash_platform_data ixdp425_flash_data = {
  42         .map_name       = "cfi_probe",
  43         .width          = 2,
  44 };
  45
  46 static struct resource ixdp425_flash_resource = {
  47         .flags          = IORESOURCE_MEM,
  48 };
  49
  50 static struct platform_device ixdp425_flash = {
  51         .name           = "IXP4XX-Flash",
  52         .id             = 0,
  53         .dev            = {
  54                 .platform_data = &ixdp425_flash_data,
  55         },
  56         .num_resources  = 1,
  57         .resource       = &ixdp425_flash_resource,
  58 };
  59
  60 #if defined(CONFIG_MTD_NAND_PLATFORM) || \
  61     defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
  62
  63 #ifdef CONFIG_MTD_PARTITIONS
  64 const char *part_probes[] = { "cmdlinepart", NULL };
  65
  66 static struct mtd_partition ixdp425_partitions[] = {
  67         {
  68                 .name   = "ixp400 NAND FS 0",
  69                 .offset = 0,
  70                 .size   = SZ_8M
  71         }, {
  72                 .name   = "ixp400 NAND FS 1",
  73                 .offset = MTDPART_OFS_APPEND,
  74                 .size   = MTDPART_SIZ_FULL
  75         },
  76 };
  77 #endif
  78
  79 static void
  80 ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
  81 {
  82         struct nand_chip *this = mtd->priv;
  83         int offset = (int)this->priv;
  84
  85         if (ctrl & NAND_CTRL_CHANGE) {
  86                 if (ctrl & NAND_NCE) {
  87                         gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_LOW);
  88                         udelay(5);
  89                 } else
  90                         gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_HIGH);
  91
  92                 offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
  93                 offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
  94                 this->priv = (void *)offset;
  95         }
  96
  97         if (cmd != NAND_CMD_NONE)
  98                 writeb(cmd, this->IO_ADDR_W + offset);
  99 }
 100
 101 static struct platform_nand_data ixdp425_flash_nand_data = {
 102         .chip = {
 103                 .nr_chips               = 1,
 104                 .chip_delay             = 30,
 105                 .options                = NAND_NO_AUTOINCR,
 106 #ifdef CONFIG_MTD_PARTITIONS
 107                 .part_probe_types       = part_probes,
 108                 .partitions             = ixdp425_partitions,
 109                 .nr_partitions          = ARRAY_SIZE(ixdp425_partitions),
 110 #endif
 111         },
 112         .ctrl = {
 113                 .cmd_ctrl               = ixdp425_flash_nand_cmd_ctrl
 114         }
 115 };
 116
 117 static struct resource ixdp425_flash_nand_resource = {
 118         .flags          = IORESOURCE_MEM,
 119 };
 120
 121 static struct platform_device ixdp425_flash_nand = {
 122         .name           = "gen_nand",
 123         .id             = -1,
 124         .dev            = {
 125                 .platform_data = &ixdp425_flash_nand_data,
 126         },
 127         .num_resources  = 1,
 128         .resource       = &ixdp425_flash_nand_resource,
 129 };
 130 #endif  /* CONFIG_MTD_NAND_PLATFORM */
 131
 132 static struct i2c_gpio_platform_data ixdp425_i2c_gpio_data = {
 133         .sda_pin        = IXDP425_SDA_PIN,
 134         .scl_pin        = IXDP425_SCL_PIN,
 135 };
 136
 137 static struct platform_device ixdp425_i2c_gpio = {
 138         .name           = "i2c-gpio",
 139         .id             = 0,
 140         .dev     = {
 141                 .platform_data  = &ixdp425_i2c_gpio_data,
 142         },
 143 };
 144
 145 static struct resource ixdp425_uart_resources[] = {
 146         {
 147                 .start          = IXP4XX_UART1_BASE_PHYS,
 148                 .end            = IXP4XX_UART1_BASE_PHYS + 0x0fff,
 149                 .flags          = IORESOURCE_MEM
 150         },
 151         {
 152                 .start          = IXP4XX_UART2_BASE_PHYS,
 153                 .end            = IXP4XX_UART2_BASE_PHYS + 0x0fff,
 154                 .flags          = IORESOURCE_MEM
 155         }
 156 };
 157
 158 static struct plat_serial8250_port ixdp425_uart_data[] = {
 159         {
 160                 .mapbase        = IXP4XX_UART1_BASE_PHYS,
 161                 .membase        = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
 162                 .irq            = IRQ_IXP4XX_UART1,
 163                 .flags          = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
 164                 .iotype         = UPIO_MEM,
 165                 .regshift       = 2,
 166                 .uartclk        = IXP4XX_UART_XTAL,
 167         },
 168         {
 169                 .mapbase        = IXP4XX_UART2_BASE_PHYS,
 170                 .membase        = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
 171                 .irq            = IRQ_IXP4XX_UART2,
 172                 .flags          = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
 173                 .iotype         = UPIO_MEM,
 174                 .regshift       = 2,
 175                 .uartclk        = IXP4XX_UART_XTAL,
 176         },
 177         { },
 178 };
 179
 180 static struct platform_device ixdp425_uart = {
 181         .name                   = "serial8250",
 182         .id                     = PLAT8250_DEV_PLATFORM,
 183         .dev.platform_data      = ixdp425_uart_data,
 184         .num_resources          = 2,
 185         .resource               = ixdp425_uart_resources
 186 };
 187
 188 /* Built-in 10/100 Ethernet MAC interfaces */
 189 static struct eth_plat_info ixdp425_plat_eth[] = {
 190         {
 191                 .phy            = 0,
 192                 .rxq            = 3,
 193                 .txreadyq       = 20,
 194         }, {
 195                 .phy            = 1,
 196                 .rxq            = 4,
 197                 .txreadyq       = 21,
 198         }
 199 };
 200
 201 static struct platform_device ixdp425_eth[] = {
 202         {
 203                 .name                   = "ixp4xx_eth",
 204                 .id                     = IXP4XX_ETH_NPEB,
 205                 .dev.platform_data      = ixdp425_plat_eth,
 206         }, {
 207                 .name                   = "ixp4xx_eth",
 208                 .id                     = IXP4XX_ETH_NPEC,
 209                 .dev.platform_data      = ixdp425_plat_eth + 1,
 210         }
 211 };
 212
 213 static struct platform_device *ixdp425_devices[] __initdata = {
 214         &ixdp425_i2c_gpio,
 215         &ixdp425_flash,
 216 #if defined(CONFIG_MTD_NAND_PLATFORM) || \
 217     defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
 218         &ixdp425_flash_nand,
 219 #endif
 220         &ixdp425_uart,
 221         &ixdp425_eth[0],
 222         &ixdp425_eth[1],
 223 };
 224
 225 static void __init ixdp425_init(void)
 226 {
 227         ixp4xx_sys_init();
 228
 229         ixdp425_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
 230         ixdp425_flash_resource.end =
 231                 IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
 232
 233 #if defined(CONFIG_MTD_NAND_PLATFORM) || \
 234     defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
 235         ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
 236         ixdp425_flash_nand_resource.end   = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
 237
 238         gpio_line_config(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_OUT);
 239
 240         /* Configure expansion bus for NAND Flash */
 241         *IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
 242                           IXP4XX_EXP_BUS_STROBE_T(1) |  /* extend by 1 clock */
 243                           IXP4XX_EXP_BUS_CYCLES(0) |    /* Intel cycles */
 244                           IXP4XX_EXP_BUS_SIZE(0) |      /* 512bytes addr space*/
 245                           IXP4XX_EXP_BUS_WR_EN |
 246                           IXP4XX_EXP_BUS_BYTE_EN;       /* 8 bit data bus */
 247 #endif
 248
 249         if (cpu_is_ixp43x()) {
 250                 ixdp425_uart.num_resources = 1;
 251                 ixdp425_uart_data[1].flags = 0;
 252         }
 253
 254         platform_add_devices(ixdp425_devices, ARRAY_SIZE(ixdp425_devices));
 255 }
 256
 257 #ifdef CONFIG_ARCH_IXDP425
 258 MACHINE_START(IXDP425, "Intel IXDP425 Development Platform")
 259         /* Maintainer: MontaVista Software, Inc. */
 260         .phys_io        = IXP4XX_PERIPHERAL_BASE_PHYS,
 261         .io_pg_offst    = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
 262         .map_io         = ixp4xx_map_io,
 263         .init_irq       = ixp4xx_init_irq,
 264         .timer          = &ixp4xx_timer,
 265         .boot_params    = 0x0100,
 266         .init_machine   = ixdp425_init,
 267 MACHINE_END
 268 #endif
 269
 270 #ifdef CONFIG_MACH_IXDP465
 271 MACHINE_START(IXDP465, "Intel IXDP465 Development Platform")
 272         /* Maintainer: MontaVista Software, Inc. */
 273         .phys_io        = IXP4XX_PERIPHERAL_BASE_PHYS,
 274         .io_pg_offst    = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
 275         .map_io         = ixp4xx_map_io,
 276         .init_irq       = ixp4xx_init_irq,
 277         .timer          = &ixp4xx_timer,
 278         .boot_params    = 0x0100,
 279         .init_machine   = ixdp425_init,
 280 MACHINE_END
 281 #endif
 282
 283 #ifdef CONFIG_ARCH_PRPMC1100
 284 MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform")
 285         /* Maintainer: MontaVista Software, Inc. */
 286         .phys_io        = IXP4XX_PERIPHERAL_BASE_PHYS,
 287         .io_pg_offst    = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
 288         .map_io         = ixp4xx_map_io,
 289         .init_irq       = ixp4xx_init_irq,
 290         .timer          = &ixp4xx_timer,
 291         .boot_params    = 0x0100,
 292         .init_machine   = ixdp425_init,
 293 MACHINE_END
 294 #endif
 295
 296 #ifdef CONFIG_MACH_KIXRP435
 297 MACHINE_START(KIXRP435, "Intel KIXRP435 Reference Platform")
 298         /* Maintainer: MontaVista Software, Inc. */
 299         .phys_io        = IXP4XX_PERIPHERAL_BASE_PHYS,
 300         .io_pg_offst    = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
 301         .map_io         = ixp4xx_map_io,
 302         .init_irq       = ixp4xx_init_irq,
 303         .timer          = &ixp4xx_timer,
 304         .boot_params    = 0x0100,
 305         .init_machine   = ixdp425_init,
 306 MACHINE_END
 307 #endif