drivers/ata/pata_radisys.c

   1 /*
   2  *    pata_radisys.c - Intel PATA/SATA controllers
   3  *
   4  *      (C) 2006 Red Hat <alan@redhat.com>
   5  *
   6  *    Some parts based on ata_piix.c by Jeff Garzik and others.
   7  *
   8  *    A PIIX relative, this device has a single ATA channel and no
   9  *    slave timings, SITRE or PPE. In that sense it is a close relative
  10  *    of the original PIIX. It does however support UDMA 33/66 per channel
  11  *    although no other modes/timings. Also lacking is 32bit I/O on the ATA
  12  *    port.
  13  */
  14
  15 #include <linux/kernel.h>
  16 #include <linux/module.h>
  17 #include <linux/pci.h>
  18 #include <linux/init.h>
  19 #include <linux/blkdev.h>
  20 #include <linux/delay.h>
  21 #include <linux/device.h>
  22 #include <scsi/scsi_host.h>
  23 #include <linux/libata.h>
  24 #include <linux/ata.h>
  25
  26 #define DRV_NAME        "pata_radisys"
  27 #define DRV_VERSION     "0.4.4"
  28
  29 /**
  30  *      radisys_set_piomode - Initialize host controller PATA PIO timings
  31  *      @ap: ATA port
  32  *      @adev: Device whose timings we are configuring
  33  *
  34  *      Set PIO mode for device, in host controller PCI config space.
  35  *
  36  *      LOCKING:
  37  *      None (inherited from caller).
  38  */
  39
  40 static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
  41 {
  42         unsigned int pio        = adev->pio_mode - XFER_PIO_0;
  43         struct pci_dev *dev     = to_pci_dev(ap->host->dev);
  44         u16 idetm_data;
  45         int control = 0;
  46
  47         /*
  48          *      See Intel Document 298600-004 for the timing programing rules
  49          *      for PIIX/ICH. Note that the early PIIX does not have the slave
  50          *      timing port at 0x44. The Radisys is a relative of the PIIX
  51          *      but not the same so be careful.
  52          */
  53
  54         static const     /* ISP  RTC */
  55         u8 timings[][2] = { { 0, 0 },   /* Check me */
  56                             { 0, 0 },
  57                             { 1, 1 },
  58                             { 2, 2 },
  59                             { 3, 3 }, };
  60
  61         if (pio > 0)
  62                 control |= 1;   /* TIME1 enable */
  63         if (ata_pio_need_iordy(adev))
  64                 control |= 2;   /* IE IORDY */
  65
  66         pci_read_config_word(dev, 0x40, &idetm_data);
  67
  68         /* Enable IE and TIME as appropriate. Clear the other
  69            drive timing bits */
  70         idetm_data &= 0xCCCC;
  71         idetm_data |= (control << (4 * adev->devno));
  72         idetm_data |= (timings[pio][0] << 12) |
  73                         (timings[pio][1] << 8);
  74         pci_write_config_word(dev, 0x40, idetm_data);
  75
  76         /* Track which port is configured */
  77         ap->private_data = adev;
  78 }
  79
  80 /**
  81  *      radisys_set_dmamode - Initialize host controller PATA DMA timings
  82  *      @ap: Port whose timings we are configuring
  83  *      @adev: Device to program
  84  *      @isich: True if the device is an ICH and has IOCFG registers
  85  *
  86  *      Set MWDMA mode for device, in host controller PCI config space.
  87  *
  88  *      LOCKING:
  89  *      None (inherited from caller).
  90  */
  91
  92 static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
  93 {
  94         struct pci_dev *dev     = to_pci_dev(ap->host->dev);
  95         u16 idetm_data;
  96         u8 udma_enable;
  97
  98         static const     /* ISP  RTC */
  99         u8 timings[][2] = { { 0, 0 },
 100                             { 0, 0 },
 101                             { 1, 1 },
 102                             { 2, 2 },
 103                             { 3, 3 }, };
 104
 105         /*
 106          * MWDMA is driven by the PIO timings. We must also enable
 107          * IORDY unconditionally.
 108          */
 109
 110         pci_read_config_word(dev, 0x40, &idetm_data);
 111         pci_read_config_byte(dev, 0x48, &udma_enable);
 112
 113         if (adev->dma_mode < XFER_UDMA_0) {
 114                 unsigned int mwdma      = adev->dma_mode - XFER_MW_DMA_0;
 115                 const unsigned int needed_pio[3] = {
 116                         XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
 117                 };
 118                 int pio = needed_pio[mwdma] - XFER_PIO_0;
 119                 int control = 3;        /* IORDY|TIME0 */
 120
 121                 /* If the drive MWDMA is faster than it can do PIO then
 122                    we must force PIO0 for PIO cycles. */
 123
 124                 if (adev->pio_mode < needed_pio[mwdma])
 125                         control = 1;
 126
 127                 /* Mask out the relevant control and timing bits we will load. Also
 128                    clear the other drive TIME register as a precaution */
 129
 130                 idetm_data &= 0xCCCC;
 131                 idetm_data |= control << (4 * adev->devno);
 132                 idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
 133
 134                 udma_enable &= ~(1 << adev->devno);
 135         } else {
 136                 u8 udma_mode;
 137
 138                 /* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */
 139
 140                 pci_read_config_byte(dev, 0x4A, &udma_mode);
 141
 142                 if (adev->xfer_mode == XFER_UDMA_2)
 143                         udma_mode &= ~ (1 << adev->devno);
 144                 else /* UDMA 4 */
 145                         udma_mode |= (1 << adev->devno);
 146
 147                 pci_write_config_byte(dev, 0x4A, udma_mode);
 148
 149                 udma_enable |= (1 << adev->devno);
 150         }
 151         pci_write_config_word(dev, 0x40, idetm_data);
 152         pci_write_config_byte(dev, 0x48, udma_enable);
 153
 154         /* Track which port is configured */
 155         ap->private_data = adev;
 156 }
 157
 158 /**
 159  *      radisys_qc_issue_prot   -       command issue
 160  *      @qc: command pending
 161  *
 162  *      Called when the libata layer is about to issue a command. We wrap
 163  *      this interface so that we can load the correct ATA timings if
 164  *      neccessary. Our logic also clears TIME0/TIME1 for the other device so
 165  *      that, even if we get this wrong, cycles to the other device will
 166  *      be made PIO0.
 167  */
 168
 169 static unsigned int radisys_qc_issue_prot(struct ata_queued_cmd *qc)
 170 {
 171         struct ata_port *ap = qc->ap;
 172         struct ata_device *adev = qc->dev;
 173
 174         if (adev != ap->private_data) {
 175                 /* UDMA timing is not shared */
 176                 if (adev->dma_mode < XFER_UDMA_0) {
 177                         if (adev->dma_mode)
 178                                 radisys_set_dmamode(ap, adev);
 179                         else if (adev->pio_mode)
 180                                 radisys_set_piomode(ap, adev);
 181                 }
 182         }
 183         return ata_qc_issue_prot(qc);
 184 }
 185
 186
 187 static struct scsi_host_template radisys_sht = {
 188         .module                 = THIS_MODULE,
 189         .name                   = DRV_NAME,
 190         .ioctl                  = ata_scsi_ioctl,
 191         .queuecommand           = ata_scsi_queuecmd,
 192         .can_queue              = ATA_DEF_QUEUE,
 193         .this_id                = ATA_SHT_THIS_ID,
 194         .sg_tablesize           = LIBATA_MAX_PRD,
 195         .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
 196         .emulated               = ATA_SHT_EMULATED,
 197         .use_clustering         = ATA_SHT_USE_CLUSTERING,
 198         .proc_name              = DRV_NAME,
 199         .dma_boundary           = ATA_DMA_BOUNDARY,
 200         .slave_configure        = ata_scsi_slave_config,
 201         .slave_destroy          = ata_scsi_slave_destroy,
 202         .bios_param             = ata_std_bios_param,
 203 };
 204
 205 static const struct ata_port_operations radisys_pata_ops = {
 206         .port_disable           = ata_port_disable,
 207         .set_piomode            = radisys_set_piomode,
 208         .set_dmamode            = radisys_set_dmamode,
 209         .mode_filter            = ata_pci_default_filter,
 210
 211         .tf_load                = ata_tf_load,
 212         .tf_read                = ata_tf_read,
 213         .check_status           = ata_check_status,
 214         .exec_command           = ata_exec_command,
 215         .dev_select             = ata_std_dev_select,
 216
 217         .freeze                 = ata_bmdma_freeze,
 218         .thaw                   = ata_bmdma_thaw,
 219         .error_handler          = ata_bmdma_error_handler,
 220         .post_internal_cmd      = ata_bmdma_post_internal_cmd,
 221         .cable_detect           = ata_cable_unknown,
 222
 223         .bmdma_setup            = ata_bmdma_setup,
 224         .bmdma_start            = ata_bmdma_start,
 225         .bmdma_stop             = ata_bmdma_stop,
 226         .bmdma_status           = ata_bmdma_status,
 227         .qc_prep                = ata_qc_prep,
 228         .qc_issue               = radisys_qc_issue_prot,
 229         .data_xfer              = ata_data_xfer,
 230
 231         .irq_handler            = ata_interrupt,
 232         .irq_clear              = ata_bmdma_irq_clear,
 233         .irq_on                 = ata_irq_on,
 234         .irq_ack                = ata_irq_ack,
 235
 236         .port_start             = ata_port_start,
 237 };
 238
 239
 240 /**
 241  *      radisys_init_one - Register PIIX ATA PCI device with kernel services
 242  *      @pdev: PCI device to register
 243  *      @ent: Entry in radisys_pci_tbl matching with @pdev
 244  *
 245  *      Called from kernel PCI layer.  We probe for combined mode (sigh),
 246  *      and then hand over control to libata, for it to do the rest.
 247  *
 248  *      LOCKING:
 249  *      Inherited from PCI layer (may sleep).
 250  *
 251  *      RETURNS:
 252  *      Zero on success, or -ERRNO value.
 253  */
 254
 255 static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 256 {
 257         static int printed_version;
 258         static const struct ata_port_info info = {
 259                 .sht            = &radisys_sht,
 260                 .flags          = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
 261                 .pio_mask       = 0x1f, /* pio0-4 */
 262                 .mwdma_mask     = 0x07, /* mwdma1-2 */
 263                 .udma_mask      = 0x14, /* UDMA33/66 only */
 264                 .port_ops       = &radisys_pata_ops,
 265         };
 266         const struct ata_port_info *ppi[] = { &info, NULL };
 267
 268         if (!printed_version++)
 269                 dev_printk(KERN_DEBUG, &pdev->dev,
 270                            "version " DRV_VERSION "\n");
 271
 272         return ata_pci_init_one(pdev, ppi);
 273 }
 274
 275 static const struct pci_device_id radisys_pci_tbl[] = {
 276         { PCI_VDEVICE(RADISYS, 0x8201), },
 277
 278         { }     /* terminate list */
 279 };
 280
 281 static struct pci_driver radisys_pci_driver = {
 282         .name                   = DRV_NAME,
 283         .id_table               = radisys_pci_tbl,
 284         .probe                  = radisys_init_one,
 285         .remove                 = ata_pci_remove_one,
 286 #ifdef CONFIG_PM
 287         .suspend                = ata_pci_device_suspend,
 288         .resume                 = ata_pci_device_resume,
 289 #endif
 290 };
 291
 292 static int __init radisys_init(void)
 293 {
 294         return pci_register_driver(&radisys_pci_driver);
 295 }
 296
 297 static void __exit radisys_exit(void)
 298 {
 299         pci_unregister_driver(&radisys_pci_driver);
 300 }
 301
 302 module_init(radisys_init);
 303 module_exit(radisys_exit);
 304
 305 MODULE_AUTHOR("Alan Cox");
 306 MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers");
 307 MODULE_LICENSE("GPL");
 308 MODULE_DEVICE_TABLE(pci, radisys_pci_tbl);
 309 MODULE_VERSION(DRV_VERSION);
 310