x86: smpboot - wakeup_secondary should be done via __cpuinit section

[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / drivers / net / de620.c

/*
 *      de620.c $Revision: 1.40 $ BETA
 *
 *
 *      Linux driver for the D-Link DE-620 Ethernet pocket adapter.
 *
 *      Portions (C) Copyright 1993, 1994 by Bjorn Ekwall <bj0rn@blox.se>
 *
 *      Based on adapter information gathered from DOS packetdriver
 *      sources from D-Link Inc:  (Special thanks to Henry Ngai of D-Link.)
 *              Portions (C) Copyright D-Link SYSTEM Inc. 1991, 1992
 *              Copyright, 1988, Russell Nelson, Crynwr Software
 *
 *      Adapted to the sample network driver core for linux,
 *      written by: Donald Becker <becker@super.org>
 *              (Now at <becker@scyld.com>)
 *
 *      Valuable assistance from:
 *              J. Joshua Kopper <kopper@rtsg.mot.com>
 *              Olav Kvittem <Olav.Kvittem@uninett.no>
 *              Germano Caronni <caronni@nessie.cs.id.ethz.ch>
 *              Jeremy Fitzhardinge <jeremy@suite.sw.oz.au>
 *
 *****************************************************************************/
/*
 *      This program is free software; you can redistribute it and/or modify
 *      it under the terms of the GNU General Public License as published by
 *      the Free Software Foundation; either version 2, or (at your option)
 *      any later version.
 *
 *      This program is distributed in the hope that it will be useful,
 *      but WITHOUT ANY WARRANTY; without even the implied warranty of
 *      MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *      GNU General Public License for more details.
 *
 *      You should have received a copy of the GNU General Public License
 *      along with this program; if not, write to the Free Software
 *      Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 *
 *****************************************************************************/
static const char version[] =
        "de620.c: $Revision: 1.40 $,  Bjorn Ekwall <bj0rn@blox.se>\n";

/***********************************************************************
 *
 * "Tuning" section.
 *
 * Compile-time options: (see below for descriptions)
 * -DDE620_IO=0x378     (lpt1)
 * -DDE620_IRQ=7        (lpt1)
 * -DDE602_DEBUG=...
 * -DSHUTDOWN_WHEN_LOST
 * -DCOUNT_LOOPS
 * -DLOWSPEED
 * -DREAD_DELAY
 * -DWRITE_DELAY
 */

/*
 * This driver assumes that the printer port is a "normal",
 * dumb, uni-directional port!
 * If your port is "fancy" in any way, please try to set it to "normal"
 * with your BIOS setup.  I have no access to machines with bi-directional
 * ports, so I can't test such a driver :-(
 * (Yes, I _know_ it is possible to use DE620 with bidirectional ports...)
 *
 * There are some clones of DE620 out there, with different names.
 * If the current driver does not recognize a clone, try to change
 * the following #define to:
 *
 * #define DE620_CLONE 1
 */
#define DE620_CLONE 0

/*
 * If the adapter has problems with high speeds, enable this #define
 * otherwise full printerport speed will be attempted.
 *
 * You can tune the READ_DELAY/WRITE_DELAY below if you enable LOWSPEED
 *
#define LOWSPEED
 */

#ifndef READ_DELAY
#define READ_DELAY 100  /* adapter internal read delay in 100ns units */
#endif

#ifndef WRITE_DELAY
#define WRITE_DELAY 100 /* adapter internal write delay in 100ns units */
#endif

/*
 * Enable this #define if you want the adapter to do a "ifconfig down" on
 * itself when we have detected that something is possibly wrong with it.
 * The default behaviour is to retry with "adapter_init()" until success.
 * This should be used for debugging purposes only.
 *
#define SHUTDOWN_WHEN_LOST
 */

/*
 * Enable debugging by "-DDE620_DEBUG=3" when compiling,
 * OR by enabling the following #define
 *
 * use 0 for production, 1 for verification, >2 for debug
 *
#define DE620_DEBUG 3
 */

#ifdef LOWSPEED
/*
 * Enable this #define if you want to see debugging output that show how long
 * we have to wait before the DE-620 is ready for the next read/write/command.
 *
#define COUNT_LOOPS
 */
#endif

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/fcntl.h>
#include <linux/string.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/in.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/inet.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>

#include <asm/io.h>
#include <asm/system.h>

/* Constant definitions for the DE-620 registers, commands and bits */
#include "de620.h"

typedef unsigned char byte;

/*******************************************************
 *                                                     *
 * Definition of D-Link DE-620 Ethernet Pocket adapter *
 * See also "de620.h"                                  *
 *                                                     *
 *******************************************************/
#ifndef DE620_IO /* Compile-time configurable */
#define DE620_IO 0x378
#endif

#ifndef DE620_IRQ /* Compile-time configurable */
#define DE620_IRQ       7
#endif

#define DATA_PORT       (dev->base_addr)
#define STATUS_PORT     (dev->base_addr + 1)
#define COMMAND_PORT    (dev->base_addr + 2)

#define RUNT 60         /* Too small Ethernet packet */
#define GIANT 1514      /* largest legal size packet, no fcs */

#ifdef DE620_DEBUG /* Compile-time configurable */
#define PRINTK(x) if (de620_debug >= 2) printk x
#else
#define DE620_DEBUG 0
#define PRINTK(x) /**/
#endif


/*
 * Force media with insmod:
 *      insmod de620.o bnc=1
 * or
 *      insmod de620.o utp=1
 *
 * Force io and/or irq with insmod:
 *      insmod de620.o io=0x378 irq=7
 *
 * Make a clone skip the Ethernet-address range check:
 *      insmod de620.o clone=1
 */
static int bnc;
static int utp;
static int io  = DE620_IO;
static int irq = DE620_IRQ;
static int clone = DE620_CLONE;

static unsigned int de620_debug = DE620_DEBUG;

static spinlock_t de620_lock;

module_param(bnc, int, 0);
module_param(utp, int, 0);
module_param(io, int, 0);
module_param(irq, int, 0);
module_param(clone, int, 0);
module_param(de620_debug, int, 0);
MODULE_PARM_DESC(bnc, "DE-620 set BNC medium (0-1)");
MODULE_PARM_DESC(utp, "DE-620 set UTP medium (0-1)");
MODULE_PARM_DESC(io, "DE-620 I/O base address,required");
MODULE_PARM_DESC(irq, "DE-620 IRQ number,required");
MODULE_PARM_DESC(clone, "Check also for non-D-Link DE-620 clones (0-1)");
MODULE_PARM_DESC(de620_debug, "DE-620 debug level (0-2)");

/***********************************************
 *                                             *
 * Index to functions, as function prototypes. *
 *                                             *
 ***********************************************/

/*
 * Routines used internally. (See also "convenience macros.. below")
 */

/* Put in the device structure. */
static int      de620_open(struct net_device *);
static int      de620_close(struct net_device *);
static void     de620_set_multicast_list(struct net_device *);
static int      de620_start_xmit(struct sk_buff *, struct net_device *);

/* Dispatch from interrupts. */
static irqreturn_t de620_interrupt(int, void *);
static int      de620_rx_intr(struct net_device *);

/* Initialization */
static int      adapter_init(struct net_device *);
static int      read_eeprom(struct net_device *);


/*
 * D-Link driver variables:
 */
#define SCR_DEF NIBBLEMODE |INTON | SLEEP | AUTOTX
#define TCR_DEF RXPB                    /* not used: | TXSUCINT | T16INT */
#define DE620_RX_START_PAGE 12          /* 12 pages (=3k) reserved for tx */
#define DEF_NIC_CMD IRQEN | ICEN | DS1

static volatile byte    NIC_Cmd;
static volatile byte    next_rx_page;
static byte             first_rx_page;
static byte             last_rx_page;
static byte             EIPRegister;

static struct nic {
        byte    NodeID[6];
        byte    RAM_Size;
        byte    Model;
        byte    Media;
        byte    SCR;
} nic_data;

/**********************************************************
 *                                                        *
 * Convenience macros/functions for D-Link DE-620 adapter *
 *                                                        *
 **********************************************************/
#define de620_tx_buffs(dd) (inb(STATUS_PORT) & (TXBF0 | TXBF1))
#define de620_flip_ds(dd) NIC_Cmd ^= DS0 | DS1; outb(NIC_Cmd, COMMAND_PORT);

/* Check for ready-status, and return a nibble (high 4 bits) for data input */
#ifdef COUNT_LOOPS
static int tot_cnt;
#endif
static inline byte
de620_ready(struct net_device *dev)
{
        byte value;
        register short int cnt = 0;

        while ((((value = inb(STATUS_PORT)) & READY) == 0) && (cnt <= 1000))
                ++cnt;

#ifdef COUNT_LOOPS
        tot_cnt += cnt;
#endif
        return value & 0xf0; /* nibble */
}

static inline void
de620_send_command(struct net_device *dev, byte cmd)
{
        de620_ready(dev);
        if (cmd == W_DUMMY)
                outb(NIC_Cmd, COMMAND_PORT);

        outb(cmd, DATA_PORT);

        outb(NIC_Cmd ^ CS0, COMMAND_PORT);
        de620_ready(dev);
        outb(NIC_Cmd, COMMAND_PORT);
}

static inline void
de620_put_byte(struct net_device *dev, byte value)
{
        /* The de620_ready() makes 7 loops, on the average, on a DX2/66 */
        de620_ready(dev);
        outb(value, DATA_PORT);
        de620_flip_ds(dev);
}

static inline byte
de620_read_byte(struct net_device *dev)
{
        byte value;

        /* The de620_ready() makes 7 loops, on the average, on a DX2/66 */
        value = de620_ready(dev); /* High nibble */
        de620_flip_ds(dev);
        value |= de620_ready(dev) >> 4; /* Low nibble */
        return value;
}

static inline void
de620_write_block(struct net_device *dev, byte *buffer, int count, int pad)
{
#ifndef LOWSPEED
        byte uflip = NIC_Cmd ^ (DS0 | DS1);
        byte dflip = NIC_Cmd;
#else /* LOWSPEED */
#ifdef COUNT_LOOPS
        int bytes = count;
#endif /* COUNT_LOOPS */
#endif /* LOWSPEED */

#ifdef LOWSPEED
#ifdef COUNT_LOOPS
        tot_cnt = 0;
#endif /* COUNT_LOOPS */
        /* No further optimization useful, the limit is in the adapter. */
        for ( ; count > 0; --count, ++buffer) {
                de620_put_byte(dev,*buffer);
        }
        for ( count = pad ; count > 0; --count, ++buffer) {
                de620_put_byte(dev, 0);
        }
        de620_send_command(dev,W_DUMMY);
#ifdef COUNT_LOOPS
        /* trial debug output: loops per byte in de620_ready() */
        printk("WRITE(%d)\n", tot_cnt/((bytes?bytes:1)));
#endif /* COUNT_LOOPS */
#else /* not LOWSPEED */
        for ( ; count > 0; count -=2) {
                outb(*buffer++, DATA_PORT);
                outb(uflip, COMMAND_PORT);
                outb(*buffer++, DATA_PORT);
                outb(dflip, COMMAND_PORT);
        }
        de620_send_command(dev,W_DUMMY);
#endif /* LOWSPEED */
}

static inline void
de620_read_block(struct net_device *dev, byte *data, int count)
{
#ifndef LOWSPEED
        byte value;
        byte uflip = NIC_Cmd ^ (DS0 | DS1);
        byte dflip = NIC_Cmd;
#else /* LOWSPEED */
#ifdef COUNT_LOOPS
        int bytes = count;

        tot_cnt = 0;
#endif /* COUNT_LOOPS */
#endif /* LOWSPEED */

#ifdef LOWSPEED
        /* No further optimization useful, the limit is in the adapter. */
        while (count-- > 0) {
                *data++ = de620_read_byte(dev);
                de620_flip_ds(dev);
        }
#ifdef COUNT_LOOPS
        /* trial debug output: loops per byte in de620_ready() */
        printk("READ(%d)\n", tot_cnt/(2*(bytes?bytes:1)));
#endif /* COUNT_LOOPS */
#else /* not LOWSPEED */
        while (count-- > 0) {
                value = inb(STATUS_PORT) & 0xf0; /* High nibble */
                outb(uflip, COMMAND_PORT);
                *data++ = value | inb(STATUS_PORT) >> 4; /* Low nibble */
                outb(dflip , COMMAND_PORT);
        }
#endif /* LOWSPEED */
}

static inline void
de620_set_delay(struct net_device *dev)
{
        de620_ready(dev);
        outb(W_DFR, DATA_PORT);
        outb(NIC_Cmd ^ CS0, COMMAND_PORT);

        de620_ready(dev);
#ifdef LOWSPEED
        outb(WRITE_DELAY, DATA_PORT);
#else
        outb(0, DATA_PORT);
#endif
        de620_flip_ds(dev);

        de620_ready(dev);
#ifdef LOWSPEED
        outb(READ_DELAY, DATA_PORT);
#else
        outb(0, DATA_PORT);
#endif
        de620_flip_ds(dev);
}

static inline void
de620_set_register(struct net_device *dev, byte reg, byte value)
{
        de620_ready(dev);
        outb(reg, DATA_PORT);
        outb(NIC_Cmd ^ CS0, COMMAND_PORT);

        de620_put_byte(dev, value);
}

static inline byte
de620_get_register(struct net_device *dev, byte reg)
{
        byte value;

        de620_send_command(dev,reg);
        value = de620_read_byte(dev);
        de620_send_command(dev,W_DUMMY);

        return value;
}

/*********************************************************************
 *
 * Open/initialize the board.
 *
 * This routine should set everything up anew at each open, even
 * registers that "should" only need to be set once at boot, so that
 * there is a non-reboot way to recover if something goes wrong.
 *
 */
static int de620_open(struct net_device *dev)
{
        int ret = request_irq(dev->irq, de620_interrupt, 0, dev->name, dev);
        if (ret) {
                printk (KERN_ERR "%s: unable to get IRQ %d\n", dev->name, dev->irq);
                return ret;
        }

        if (adapter_init(dev)) {
                ret = -EIO;
                goto out_free_irq;
        }

        netif_start_queue(dev);
        return 0;

out_free_irq:
        free_irq(dev->irq, dev);
        return ret;
}

/************************************************
 *
 * The inverse routine to de620_open().
 *
 */

static int de620_close(struct net_device *dev)
{
        netif_stop_queue(dev);
        /* disable recv */
        de620_set_register(dev, W_TCR, RXOFF);
        free_irq(dev->irq, dev);
        return 0;
}

/*********************************************
 *
 * Set or clear the multicast filter for this adaptor.
 * (no real multicast implemented for the DE-620, but she can be promiscuous...)
 *
 */

static void de620_set_multicast_list(struct net_device *dev)
{
        if (dev->mc_count || dev->flags&(IFF_ALLMULTI|IFF_PROMISC))
        { /* Enable promiscuous mode */
                de620_set_register(dev, W_TCR, (TCR_DEF & ~RXPBM) | RXALL);
        }
        else
        { /* Disable promiscuous mode, use normal mode */
                de620_set_register(dev, W_TCR, TCR_DEF);
        }
}

/*******************************************************
 *
 * Handle timeouts on transmit
 */

static void de620_timeout(struct net_device *dev)
{
        printk(KERN_WARNING "%s: transmit timed out, %s?\n", dev->name, "network cable problem");
        /* Restart the adapter. */
        if (!adapter_init(dev)) /* maybe close it */
                netif_wake_queue(dev);
}

/*******************************************************
 *
 * Copy a buffer to the adapter transmit page memory.
 * Start sending.
 */
static int de620_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
        unsigned long flags;
        int len;
        byte *buffer = skb->data;
        byte using_txbuf;

        using_txbuf = de620_tx_buffs(dev); /* Peek at the adapter */

        netif_stop_queue(dev);


        if ((len = skb->len) < RUNT)
                len = RUNT;
        if (len & 1) /* send an even number of bytes */
                ++len;

        /* Start real output */

        spin_lock_irqsave(&de620_lock, flags)
        PRINTK(("de620_start_xmit: len=%d, bufs 0x%02x\n",
                (int)skb->len, using_txbuf));

        /* select a free tx buffer. if there is one... */
        switch (using_txbuf) {
        default: /* both are free: use TXBF0 */
        case TXBF1: /* use TXBF0 */
                de620_send_command(dev,W_CR | RW0);
                using_txbuf |= TXBF0;
                break;

        case TXBF0: /* use TXBF1 */
                de620_send_command(dev,W_CR | RW1);
                using_txbuf |= TXBF1;
                break;

        case (TXBF0 | TXBF1): /* NONE!!! */
                printk(KERN_WARNING "%s: No tx-buffer available!\n", dev->name);
                spin_unlock_irqrestore(&de620_lock, flags);
                return 1;
        }
        de620_write_block(dev, buffer, skb->len, len-skb->len);

        dev->trans_start = jiffies;
        if(!(using_txbuf == (TXBF0 | TXBF1)))
                netif_wake_queue(dev);

        dev->stats.tx_packets++;
        spin_unlock_irqrestore(&de620_lock, flags);
        dev_kfree_skb (skb);
        return 0;
}

/*****************************************************
 *
 * Handle the network interface interrupts.
 *
 */
static irqreturn_t
de620_interrupt(int irq_in, void *dev_id)
{
        struct net_device *dev = dev_id;
        byte irq_status;
        int bogus_count = 0;
        int again = 0;

        spin_lock(&de620_lock);

        /* Read the status register (_not_ the status port) */
        irq_status = de620_get_register(dev, R_STS);

        PRINTK(("de620_interrupt (%2.2X)\n", irq_status));

        if (irq_status & RXGOOD) {
                do {
                        again = de620_rx_intr(dev);
                        PRINTK(("again=%d\n", again));
                }
                while (again && (++bogus_count < 100));
        }

        if(de620_tx_buffs(dev) != (TXBF0 | TXBF1))
                netif_wake_queue(dev);

        spin_unlock(&de620_lock);
        return IRQ_HANDLED;
}

/**************************************
 *
 * Get a packet from the adapter
 *
 * Send it "upstairs"
 *
 */
static int de620_rx_intr(struct net_device *dev)
{
        struct header_buf {
                byte            status;
                byte            Rx_NextPage;
                unsigned short  Rx_ByteCount;
        } header_buf;
        struct sk_buff *skb;
        int size;
        byte *buffer;
        byte pagelink;
        byte curr_page;

        PRINTK(("de620_rx_intr: next_rx_page = %d\n", next_rx_page));

        /* Tell the adapter that we are going to read data, and from where */
        de620_send_command(dev, W_CR | RRN);
        de620_set_register(dev, W_RSA1, next_rx_page);
        de620_set_register(dev, W_RSA0, 0);

        /* Deep breath, and away we goooooo */
        de620_read_block(dev, (byte *)&header_buf, sizeof(struct header_buf));
        PRINTK(("page status=0x%02x, nextpage=%d, packetsize=%d\n",
        header_buf.status, header_buf.Rx_NextPage, header_buf.Rx_ByteCount));

        /* Plausible page header? */
        pagelink = header_buf.Rx_NextPage;
        if ((pagelink < first_rx_page) || (last_rx_page < pagelink)) {
                /* Ouch... Forget it! Skip all and start afresh... */
                printk(KERN_WARNING "%s: Ring overrun? Restoring...\n", dev->name);
                /* You win some, you lose some. And sometimes plenty... */
                adapter_init(dev);
                netif_wake_queue(dev);
                dev->stats.rx_over_errors++;
                return 0;
        }

        /* OK, this look good, so far. Let's see if it's consistent... */
        /* Let's compute the start of the next packet, based on where we are */
        pagelink = next_rx_page +
                ((header_buf.Rx_ByteCount + (4 - 1 + 0x100)) >> 8);

        /* Are we going to wrap around the page counter? */
        if (pagelink > last_rx_page)
                pagelink -= (last_rx_page - first_rx_page + 1);

        /* Is the _computed_ next page number equal to what the adapter says? */
        if (pagelink != header_buf.Rx_NextPage) {
                /* Naah, we'll skip this packet. Probably bogus data as well */
                printk(KERN_WARNING "%s: Page link out of sync! Restoring...\n", dev->name);
                next_rx_page = header_buf.Rx_NextPage; /* at least a try... */
                de620_send_command(dev, W_DUMMY);
                de620_set_register(dev, W_NPRF, next_rx_page);
                dev->stats.rx_over_errors++;
                return 0;
        }
        next_rx_page = pagelink;

        size = header_buf.Rx_ByteCount - 4;
        if ((size < RUNT) || (GIANT < size)) {
                printk(KERN_WARNING "%s: Illegal packet size: %d!\n", dev->name, size);
        }
        else { /* Good packet? */
                skb = dev_alloc_skb(size+2);
                if (skb == NULL) { /* Yeah, but no place to put it... */
                        printk(KERN_WARNING "%s: Couldn't allocate a sk_buff of size %d.\n", dev->name, size);
                        dev->stats.rx_dropped++;
                }
                else { /* Yep! Go get it! */
                        skb_reserve(skb,2);     /* Align */
                        /* skb->data points to the start of sk_buff data area */
                        buffer = skb_put(skb,size);
                        /* copy the packet into the buffer */
                        de620_read_block(dev, buffer, size);
                        PRINTK(("Read %d bytes\n", size));
                        skb->protocol=eth_type_trans(skb,dev);
                        netif_rx(skb); /* deliver it "upstairs" */
                        /* count all receives */
                        dev->stats.rx_packets++;
                        dev->stats.rx_bytes += size;
                }
        }

        /* Let's peek ahead to see if we have read the last current packet */
        /* NOTE! We're _not_ checking the 'EMPTY'-flag! This seems better... */
        curr_page = de620_get_register(dev, R_CPR);
        de620_set_register(dev, W_NPRF, next_rx_page);
        PRINTK(("next_rx_page=%d CPR=%d\n", next_rx_page, curr_page));

        return (next_rx_page != curr_page); /* That was slightly tricky... */
}

/*********************************************
 *
 * Reset the adapter to a known state
 *
 */
static int adapter_init(struct net_device *dev)
{
        int i;
        static int was_down;

        if ((nic_data.Model == 3) || (nic_data.Model == 0)) { /* CT */
                EIPRegister = NCTL0;
                if (nic_data.Media != 1)
                        EIPRegister |= NIS0;    /* not BNC */
        }
        else if (nic_data.Model == 2) { /* UTP */
                EIPRegister = NCTL0 | NIS0;
        }

        if (utp)
                EIPRegister = NCTL0 | NIS0;
        if (bnc)
                EIPRegister = NCTL0;

        de620_send_command(dev, W_CR | RNOP | CLEAR);
        de620_send_command(dev, W_CR | RNOP);

        de620_set_register(dev, W_SCR, SCR_DEF);
        /* disable recv to wait init */
        de620_set_register(dev, W_TCR, RXOFF);

        /* Set the node ID in the adapter */
        for (i = 0; i < 6; ++i) { /* W_PARn = 0xaa + n */
                de620_set_register(dev, W_PAR0 + i, dev->dev_addr[i]);
        }

        de620_set_register(dev, W_EIP, EIPRegister);

        next_rx_page = first_rx_page = DE620_RX_START_PAGE;
        if (nic_data.RAM_Size)
                last_rx_page = nic_data.RAM_Size - 1;
        else /* 64k RAM */
                last_rx_page = 255;

        de620_set_register(dev, W_SPR, first_rx_page); /* Start Page Register*/
        de620_set_register(dev, W_EPR, last_rx_page);  /* End Page Register */
        de620_set_register(dev, W_CPR, first_rx_page);/*Current Page Register*/
        de620_send_command(dev, W_NPR | first_rx_page); /* Next Page Register*/
        de620_send_command(dev, W_DUMMY);
        de620_set_delay(dev);

        /* Final sanity check: Anybody out there? */
        /* Let's hope some bits from the statusregister make a good check */
#define CHECK_MASK (  0 | TXSUC |  T16  |  0  | RXCRC | RXSHORT |  0  |  0  )
#define CHECK_OK   (  0 |   0   |  0    |  0  |   0   |   0     |  0  |  0  )
        /* success:   X     0      0       X      0       0        X     X  */
        /* ignore:   EEDI                RXGOOD                   COLS  LNKS*/

        if (((i = de620_get_register(dev, R_STS)) & CHECK_MASK) != CHECK_OK) {
                printk(KERN_ERR "%s: Something has happened to the DE-620!  Please check it"
#ifdef SHUTDOWN_WHEN_LOST
                        " and do a new ifconfig"
#endif
                        "! (%02x)\n", dev->name, i);
#ifdef SHUTDOWN_WHEN_LOST
                /* Goodbye, cruel world... */
                dev->flags &= ~IFF_UP;
                de620_close(dev);
#endif
                was_down = 1;
                return 1; /* failed */
        }
        if (was_down) {
                printk(KERN_WARNING "%s: Thanks, I feel much better now!\n", dev->name);
                was_down = 0;
        }

        /* All OK, go ahead... */
        de620_set_register(dev, W_TCR, TCR_DEF);

        return 0; /* all ok */
}

static const struct net_device_ops de620_netdev_ops = {
        .ndo_open               = de620_open,
        .ndo_stop               = de620_close,
        .ndo_start_xmit         = de620_start_xmit,
        .ndo_tx_timeout         = de620_timeout,
        .ndo_set_multicast_list = de620_set_multicast_list,
        .ndo_change_mtu         = eth_change_mtu,
        .ndo_set_mac_address    = eth_mac_addr,
        .ndo_validate_addr      = eth_validate_addr,
};

/******************************************************************************
 *
 * Only start-up code below
 *
 */
/****************************************
 *
 * Check if there is a DE-620 connected
 */
struct net_device * __init de620_probe(int unit)
{
        byte checkbyte = 0xa5;
        struct net_device *dev;
        int err = -ENOMEM;
        int i;

        dev = alloc_etherdev(0);
        if (!dev)
                goto out;

        spin_lock_init(&de620_lock);

        /*
         * This is where the base_addr and irq gets set.
         * Tunable at compile-time and insmod-time
         */
        dev->base_addr = io;
        dev->irq       = irq;

        /* allow overriding parameters on command line */
        if (unit >= 0) {
                sprintf(dev->name, "eth%d", unit);
                netdev_boot_setup_check(dev);
        }

        if (de620_debug)
                printk(version);

        printk(KERN_INFO "D-Link DE-620 pocket adapter");

        if (!request_region(dev->base_addr, 3, "de620")) {
                printk(" io 0x%3lX, which is busy.\n", dev->base_addr);
                err = -EBUSY;
                goto out1;
        }

        /* Initially, configure basic nibble mode, so we can read the EEPROM */
        NIC_Cmd = DEF_NIC_CMD;
        de620_set_register(dev, W_EIP, EIPRegister);

        /* Anybody out there? */
        de620_set_register(dev, W_CPR, checkbyte);
        checkbyte = de620_get_register(dev, R_CPR);

        if ((checkbyte != 0xa5) || (read_eeprom(dev) != 0)) {
                printk(" not identified in the printer port\n");
                err = -ENODEV;
                goto out2;
        }

        /* else, got it! */
        dev->dev_addr[0] = nic_data.NodeID[0];
        for (i = 1; i < ETH_ALEN; i++) {
                dev->dev_addr[i] = nic_data.NodeID[i];
                dev->broadcast[i] = 0xff;
        }

        printk(", Ethernet Address: %pM", dev->dev_addr);

        printk(" (%dk RAM,",
                (nic_data.RAM_Size) ? (nic_data.RAM_Size >> 2) : 64);

        if (nic_data.Media == 1)
                printk(" BNC)\n");
        else
                printk(" UTP)\n");

        dev->netdev_ops = &de620_netdev_ops;
        dev->watchdog_timeo     = HZ*2;

        /* base_addr and irq are already set, see above! */

        /* dump eeprom */
        if (de620_debug) {
                printk("\nEEPROM contents:\n");
                printk("RAM_Size = 0x%02X\n", nic_data.RAM_Size);
                printk("NodeID = %pM\n", nic_data.NodeID);
                printk("Model = %d\n", nic_data.Model);
                printk("Media = %d\n", nic_data.Media);
                printk("SCR = 0x%02x\n", nic_data.SCR);
        }

        err = register_netdev(dev);
        if (err)
                goto out2;
        return dev;

out2:
        release_region(dev->base_addr, 3);
out1:
        free_netdev(dev);
out:
        return ERR_PTR(err);
}

/**********************************
 *
 * Read info from on-board EEPROM
 *
 * Note: Bitwise serial I/O to/from the EEPROM vi the status _register_!
 */
#define sendit(dev,data) de620_set_register(dev, W_EIP, data | EIPRegister);

static unsigned short __init ReadAWord(struct net_device *dev, int from)
{
        unsigned short data;
        int nbits;

        /* cs   [__~~] SET SEND STATE */
        /* di   [____]                */
        /* sck  [_~~_]                */
        sendit(dev, 0); sendit(dev, 1); sendit(dev, 5); sendit(dev, 4);

        /* Send the 9-bit address from where we want to read the 16-bit word */
        for (nbits = 9; nbits > 0; --nbits, from <<= 1) {
                if (from & 0x0100) { /* bit set? */
                        /* cs    [~~~~] SEND 1 */
                        /* di    [~~~~]        */
                        /* sck   [_~~_]        */
                        sendit(dev, 6); sendit(dev, 7); sendit(dev, 7); sendit(dev, 6);
                }
                else {
                        /* cs    [~~~~] SEND 0 */
                        /* di    [____]        */
                        /* sck   [_~~_]        */
                        sendit(dev, 4); sendit(dev, 5); sendit(dev, 5); sendit(dev, 4);
                }
        }

        /* Shift in the 16-bit word. The bits appear serially in EEDI (=0x80) */
        for (data = 0, nbits = 16; nbits > 0; --nbits) {
                /* cs    [~~~~] SEND 0 */
                /* di    [____]        */
                /* sck   [_~~_]        */
                sendit(dev, 4); sendit(dev, 5); sendit(dev, 5); sendit(dev, 4);
                data = (data << 1) | ((de620_get_register(dev, R_STS) & EEDI) >> 7);
        }
        /* cs    [____] RESET SEND STATE */
        /* di    [____]                  */
        /* sck   [_~~_]                  */
        sendit(dev, 0); sendit(dev, 1); sendit(dev, 1); sendit(dev, 0);

        return data;
}

static int __init read_eeprom(struct net_device *dev)
{
        unsigned short wrd;

        /* D-Link Ethernet addresses are in the series  00:80:c8:7X:XX:XX:XX */
        wrd = ReadAWord(dev, 0x1aa);    /* bytes 0 + 1 of NodeID */
        if (!clone && (wrd != htons(0x0080))) /* Valid D-Link ether sequence? */
                return -1; /* Nope, not a DE-620 */
        nic_data.NodeID[0] = wrd & 0xff;
        nic_data.NodeID[1] = wrd >> 8;

        wrd = ReadAWord(dev, 0x1ab);    /* bytes 2 + 3 of NodeID */
        if (!clone && ((wrd & 0xff) != 0xc8)) /* Valid D-Link ether sequence? */
                return -1; /* Nope, not a DE-620 */
        nic_data.NodeID[2] = wrd & 0xff;
        nic_data.NodeID[3] = wrd >> 8;

        wrd = ReadAWord(dev, 0x1ac);    /* bytes 4 + 5 of NodeID */
        nic_data.NodeID[4] = wrd & 0xff;
        nic_data.NodeID[5] = wrd >> 8;

        wrd = ReadAWord(dev, 0x1ad);    /* RAM size in pages (256 bytes). 0 = 64k */
        nic_data.RAM_Size = (wrd >> 8);

        wrd = ReadAWord(dev, 0x1ae);    /* hardware model (CT = 3) */
        nic_data.Model = (wrd & 0xff);

        wrd = ReadAWord(dev, 0x1af); /* media (indicates BNC/UTP) */
        nic_data.Media = (wrd & 0xff);

        wrd = ReadAWord(dev, 0x1a8); /* System Configuration Register */
        nic_data.SCR = (wrd >> 8);

        return 0; /* no errors */
}

/******************************************************************************
 *
 * Loadable module skeleton
 *
 */
#ifdef MODULE
static struct net_device *de620_dev;

int __init init_module(void)
{
        de620_dev = de620_probe(-1);
        if (IS_ERR(de620_dev))
                return PTR_ERR(de620_dev);
        return 0;
}

void cleanup_module(void)
{
        unregister_netdev(de620_dev);
        release_region(de620_dev->base_addr, 3);
        free_netdev(de620_dev);
}
#endif /* MODULE */
MODULE_LICENSE("GPL");