arch/mips/gt64120/ev64120/serialGT.c

   1 /*
   2  * serialGT.c
   3  *
   4  * BRIEF MODULE DESCRIPTION
   5  *  Low Level Serial Port control for use
   6  *  with the Galileo EVB64120A MIPS eval board and
   7  *  its on board two channel 16552 Uart.
   8  *
   9  * Copyright (C) 2000 RidgeRun, Inc.
  10  * Author: RidgeRun, Inc.
  11  *   glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com
  12  *
  13  *  This program is free software; you can redistribute  it and/or modify it
  14  *  under  the terms of  the GNU General  Public License as published by the
  15  *  Free Software Foundation;  either version 2 of the  License, or (at your
  16  *  option) any later version.
  17  *
  18  *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
  19  *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
  20  *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
  21  *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
  22  *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
  23  *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
  24  *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
  25  *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
  26  *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
  27  *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  28  *
  29  *  You should have received a copy of the  GNU General Public License along
  30  *  with this program; if not, write  to the Free Software Foundation, Inc.,
  31  *  675 Mass Ave, Cambridge, MA 02139, USA.
  32  *
  33  */
  34
  35 // Note:
  36 //   Serial CHANNELS - 0 is the bottom connector of evb64120A.
  37 //                       (The one that maps to the "B" channel of the
  38 //                       board's uart)
  39 //                     1 is the top connector of evb64120A.
  40 //                       (The one that maps to the "A" channel of the
  41 //                       board's uart)
  42 int DEBUG_CHANNEL = 0;          // See Note Above
  43 int CONSOLE_CHANNEL = 1;        // See Note Above
  44
  45 #define DUART 0xBD000000        /* Base address of Uart. */
  46 #define CHANNELOFFSET 0x20      /* DUART+CHANNELOFFSET gets you to the ChanA
  47                                    register set of the 16552 Uart device.
  48                                    DUART+0 gets you to the ChanB register set.
  49                                  */
  50 #define DUART_DELTA 0x4
  51 #define FIFO_ENABLE 0x07
  52 #define INT_ENABLE  0x04        /* default interrupt mask */
  53
  54 #define RBR 0x00
  55 #define THR 0x00
  56 #define DLL 0x00
  57 #define IER 0x01
  58 #define DLM 0x01
  59 #define IIR 0x02
  60 #define FCR 0x02
  61 #define LCR 0x03
  62 #define MCR 0x04
  63 #define LSR 0x05
  64 #define MSR 0x06
  65 #define SCR 0x07
  66
  67 #define LCR_DLAB 0x80
  68 #define XTAL 1843200
  69 #define LSR_THRE 0x20
  70 #define LSR_BI   0x10
  71 #define LSR_DR   0x01
  72 #define MCR_LOOP 0x10
  73 #define ACCESS_DELAY 0x10000
  74
  75 /******************************
  76  Routine:
  77  Description:
  78  ******************************/
  79 int inreg(int channel, int reg)
  80 {
  81         int val;
  82         val =
  83             *((volatile unsigned char *) DUART +
  84               (channel * CHANNELOFFSET) + (reg * DUART_DELTA));
  85         return val;
  86 }
  87
  88 /******************************
  89  Routine:
  90  Description:
  91  ******************************/
  92 void outreg(int channel, int reg, unsigned char val)
  93 {
  94         *((volatile unsigned char *) DUART + (channel * CHANNELOFFSET)
  95           + (reg * DUART_DELTA)) = val;
  96 }
  97
  98 /******************************
  99  Routine:
 100  Description:
 101    Initialize the device driver.
 102  ******************************/
 103 void serial_init(int channel)
 104 {
 105         /*
 106          * Configure active port, (CHANNELOFFSET already set.)
 107          *
 108          * Set 8 bits, 1 stop bit, no parity.
 109          *
 110          * LCR<7>       0       divisor latch access bit
 111          * LCR<6>       0       break control (1=send break)
 112          * LCR<5>       0       stick parity (0=space, 1=mark)
 113          * LCR<4>       0       parity even (0=odd, 1=even)
 114          * LCR<3>       0       parity enable (1=enabled)
 115          * LCR<2>       0       # stop bits (0=1, 1=1.5)
 116          * LCR<1:0>     11      bits per character(00=5, 01=6, 10=7, 11=8)
 117          */
 118         outreg(channel, LCR, 0x3);
 119
 120         outreg(channel, FCR, FIFO_ENABLE);      /* Enable the FIFO */
 121
 122         outreg(channel, IER, INT_ENABLE);       /* Enable appropriate interrupts */
 123 }
 124
 125 /******************************
 126  Routine:
 127  Description:
 128    Set the baud rate.
 129  ******************************/
 130 void serial_set(int channel, unsigned long baud)
 131 {
 132         unsigned char sav_lcr;
 133
 134         /*
 135          * Enable access to the divisor latches by setting DLAB in LCR.
 136          *
 137          */
 138         sav_lcr = inreg(channel, LCR);
 139
 140 #if 0
 141         /*
 142          * Set baud rate
 143          */
 144         outreg(channel, LCR, LCR_DLAB | sav_lcr);
 145         //  outreg(DLL,(XTAL/(16*2*(baud))-2));
 146         outreg(channel, DLL, XTAL / (16 * baud));
 147         //  outreg(DLM,(XTAL/(16*2*(baud))-2)>>8);
 148         outreg(channel, DLM, (XTAL / (16 * baud)) >> 8);
 149 #else
 150         /*
 151          * Note: Set baud rate, hardcoded here for rate of 115200
 152          * since became unsure of above "buad rate" algorithm (??).
 153          */
 154         outreg(channel, LCR, 0x83);
 155         outreg(channel, DLM, 0x00);     // See note above
 156         outreg(channel, DLL, 0x02);     // See note above.
 157         outreg(channel, LCR, 0x03);
 158 #endif
 159
 160         /*
 161          * Restore line control register
 162          */
 163         outreg(channel, LCR, sav_lcr);
 164 }
 165
 166
 167 /******************************
 168  Routine:
 169  Description:
 170    Transmit a character.
 171  ******************************/
 172 void serial_putc(int channel, int c)
 173 {
 174         while ((inreg(channel, LSR) & LSR_THRE) == 0);
 175         outreg(channel, THR, c);
 176 }
 177
 178 /******************************
 179  Routine:
 180  Description:
 181     Read a received character if one is
 182     available.  Return -1 otherwise.
 183  ******************************/
 184 int serial_getc(int channel)
 185 {
 186         if (inreg(channel, LSR) & LSR_DR) {
 187                 return inreg(channel, RBR);
 188         }
 189         return -1;
 190 }
 191
 192 /******************************
 193  Routine:
 194  Description:
 195    Used by embedded gdb client. (example; gdb-stub.c)
 196  ******************************/
 197 char getDebugChar()
 198 {
 199         int val;
 200         while ((val = serial_getc(DEBUG_CHANNEL)) == -1);       // loop until we get a character in.
 201         return (char) val;
 202 }
 203
 204 /******************************
 205  Routine:
 206  Description:
 207    Used by embedded gdb target. (example; gdb-stub.c)
 208  ******************************/
 209 void putDebugChar(char c)
 210 {
 211         serial_putc(DEBUG_CHANNEL, (int) c);
 212 }