drivers/mmc/host/sdhci-esdhc-imx.c

   1 /*
   2  * Freescale eSDHC i.MX controller driver for the platform bus.
   3  *
   4  * derived from the OF-version.
   5  *
   6  * Copyright (c) 2010 Pengutronix e.K.
   7  *   Author: Wolfram Sang <w.sang@pengutronix.de>
   8  *
   9  * This program is free software; you can redistribute it and/or modify
  10  * it under the terms of the GNU General Public License as published by
  11  * the Free Software Foundation; either version 2 of the License.
  12  */
  13
  14 #include <linux/io.h>
  15 #include <linux/delay.h>
  16 #include <linux/err.h>
  17 #include <linux/clk.h>
  18 #include <linux/gpio.h>
  19 #include <linux/module.h>
  20 #include <linux/slab.h>
  21 #include <linux/mmc/host.h>
  22 #include <linux/mmc/mmc.h>
  23 #include <linux/mmc/sdio.h>
  24 #include <linux/of.h>
  25 #include <linux/of_device.h>
  26 #include <linux/of_gpio.h>
  27 #include <mach/esdhc.h>
  28 #include "sdhci-pltfm.h"
  29 #include "sdhci-esdhc.h"
  30
  31 #define SDHCI_CTRL_D3CD                 0x08
  32 /* VENDOR SPEC register */
  33 #define SDHCI_VENDOR_SPEC               0xC0
  34 #define  SDHCI_VENDOR_SPEC_SDIO_QUIRK   0x00000002
  35 #define SDHCI_WTMK_LVL                  0x44
  36 #define SDHCI_MIX_CTRL                  0x48
  37
  38 /*
  39  * There is an INT DMA ERR mis-match between eSDHC and STD SDHC SPEC:
  40  * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
  41  * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
  42  * Define this macro DMA error INT for fsl eSDHC
  43  */
  44 #define SDHCI_INT_VENDOR_SPEC_DMA_ERR   0x10000000
  45
  46 /*
  47  * The CMDTYPE of the CMD register (offset 0xE) should be set to
  48  * "11" when the STOP CMD12 is issued on imx53 to abort one
  49  * open ended multi-blk IO. Otherwise the TC INT wouldn't
  50  * be generated.
  51  * In exact block transfer, the controller doesn't complete the
  52  * operations automatically as required at the end of the
  53  * transfer and remains on hold if the abort command is not sent.
  54  * As a result, the TC flag is not asserted and SW  received timeout
  55  * exeception. Bit1 of Vendor Spec registor is used to fix it.
  56  */
  57 #define ESDHC_FLAG_MULTIBLK_NO_INT      (1 << 1)
  58
  59 enum imx_esdhc_type {
  60         IMX25_ESDHC,
  61         IMX35_ESDHC,
  62         IMX51_ESDHC,
  63         IMX53_ESDHC,
  64         IMX6Q_USDHC,
  65 };
  66
  67 struct pltfm_imx_data {
  68         int flags;
  69         u32 scratchpad;
  70         enum imx_esdhc_type devtype;
  71         struct esdhc_platform_data boarddata;
  72 };
  73
  74 static struct platform_device_id imx_esdhc_devtype[] = {
  75         {
  76                 .name = "sdhci-esdhc-imx25",
  77                 .driver_data = IMX25_ESDHC,
  78         }, {
  79                 .name = "sdhci-esdhc-imx35",
  80                 .driver_data = IMX35_ESDHC,
  81         }, {
  82                 .name = "sdhci-esdhc-imx51",
  83                 .driver_data = IMX51_ESDHC,
  84         }, {
  85                 .name = "sdhci-esdhc-imx53",
  86                 .driver_data = IMX53_ESDHC,
  87         }, {
  88                 .name = "sdhci-usdhc-imx6q",
  89                 .driver_data = IMX6Q_USDHC,
  90         }, {
  91                 /* sentinel */
  92         }
  93 };
  94 MODULE_DEVICE_TABLE(platform, imx_esdhc_devtype);
  95
  96 static const struct of_device_id imx_esdhc_dt_ids[] = {
  97         { .compatible = "fsl,imx25-esdhc", .data = &imx_esdhc_devtype[IMX25_ESDHC], },
  98         { .compatible = "fsl,imx35-esdhc", .data = &imx_esdhc_devtype[IMX35_ESDHC], },
  99         { .compatible = "fsl,imx51-esdhc", .data = &imx_esdhc_devtype[IMX51_ESDHC], },
 100         { .compatible = "fsl,imx53-esdhc", .data = &imx_esdhc_devtype[IMX53_ESDHC], },
 101         { .compatible = "fsl,imx6q-usdhc", .data = &imx_esdhc_devtype[IMX6Q_USDHC], },
 102         { /* sentinel */ }
 103 };
 104 MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
 105
 106 static inline int is_imx25_esdhc(struct pltfm_imx_data *data)
 107 {
 108         return data->devtype == IMX25_ESDHC;
 109 }
 110
 111 static inline int is_imx35_esdhc(struct pltfm_imx_data *data)
 112 {
 113         return data->devtype == IMX35_ESDHC;
 114 }
 115
 116 static inline int is_imx51_esdhc(struct pltfm_imx_data *data)
 117 {
 118         return data->devtype == IMX51_ESDHC;
 119 }
 120
 121 static inline int is_imx53_esdhc(struct pltfm_imx_data *data)
 122 {
 123         return data->devtype == IMX53_ESDHC;
 124 }
 125
 126 static inline int is_imx6q_usdhc(struct pltfm_imx_data *data)
 127 {
 128         return data->devtype == IMX6Q_USDHC;
 129 }
 130
 131 static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg)
 132 {
 133         void __iomem *base = host->ioaddr + (reg & ~0x3);
 134         u32 shift = (reg & 0x3) * 8;
 135
 136         writel(((readl(base) & ~(mask << shift)) | (val << shift)), base);
 137 }
 138
 139 static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
 140 {
 141         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 142         struct pltfm_imx_data *imx_data = pltfm_host->priv;
 143         struct esdhc_platform_data *boarddata = &imx_data->boarddata;
 144
 145         /* fake CARD_PRESENT flag */
 146         u32 val = readl(host->ioaddr + reg);
 147
 148         if (unlikely((reg == SDHCI_PRESENT_STATE)
 149                         && gpio_is_valid(boarddata->cd_gpio))) {
 150                 if (gpio_get_value(boarddata->cd_gpio))
 151                         /* no card, if a valid gpio says so... */
 152                         val &= ~SDHCI_CARD_PRESENT;
 153                 else
 154                         /* ... in all other cases assume card is present */
 155                         val |= SDHCI_CARD_PRESENT;
 156         }
 157
 158         if (unlikely(reg == SDHCI_CAPABILITIES)) {
 159                 /* In FSL esdhc IC module, only bit20 is used to indicate the
 160                  * ADMA2 capability of esdhc, but this bit is messed up on
 161                  * some SOCs (e.g. on MX25, MX35 this bit is set, but they
 162                  * don't actually support ADMA2). So set the BROKEN_ADMA
 163                  * uirk on MX25/35 platforms.
 164                  */
 165
 166                 if (val & SDHCI_CAN_DO_ADMA1) {
 167                         val &= ~SDHCI_CAN_DO_ADMA1;
 168                         val |= SDHCI_CAN_DO_ADMA2;
 169                 }
 170         }
 171
 172         if (unlikely(reg == SDHCI_INT_STATUS)) {
 173                 if (val & SDHCI_INT_VENDOR_SPEC_DMA_ERR) {
 174                         val &= ~SDHCI_INT_VENDOR_SPEC_DMA_ERR;
 175                         val |= SDHCI_INT_ADMA_ERROR;
 176                 }
 177         }
 178
 179         return val;
 180 }
 181
 182 static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
 183 {
 184         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 185         struct pltfm_imx_data *imx_data = pltfm_host->priv;
 186         struct esdhc_platform_data *boarddata = &imx_data->boarddata;
 187         u32 data;
 188
 189         if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
 190                 if (boarddata->cd_type == ESDHC_CD_GPIO)
 191                         /*
 192                          * These interrupts won't work with a custom
 193                          * card_detect gpio (only applied to mx25/35)
 194                          */
 195                         val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT);
 196
 197                 if (val & SDHCI_INT_CARD_INT) {
 198                         /*
 199                          * Clear and then set D3CD bit to avoid missing the
 200                          * card interrupt.  This is a eSDHC controller problem
 201                          * so we need to apply the following workaround: clear
 202                          * and set D3CD bit will make eSDHC re-sample the card
 203                          * interrupt. In case a card interrupt was lost,
 204                          * re-sample it by the following steps.
 205                          */
 206                         data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
 207                         data &= ~SDHCI_CTRL_D3CD;
 208                         writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
 209                         data |= SDHCI_CTRL_D3CD;
 210                         writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
 211                 }
 212         }
 213
 214         if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
 215                                 && (reg == SDHCI_INT_STATUS)
 216                                 && (val & SDHCI_INT_DATA_END))) {
 217                         u32 v;
 218                         v = readl(host->ioaddr + SDHCI_VENDOR_SPEC);
 219                         v &= ~SDHCI_VENDOR_SPEC_SDIO_QUIRK;
 220                         writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
 221         }
 222
 223         if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
 224                 if (val & SDHCI_INT_ADMA_ERROR) {
 225                         val &= ~SDHCI_INT_ADMA_ERROR;
 226                         val |= SDHCI_INT_VENDOR_SPEC_DMA_ERR;
 227                 }
 228         }
 229
 230         writel(val, host->ioaddr + reg);
 231 }
 232
 233 static u16 esdhc_readw_le(struct sdhci_host *host, int reg)
 234 {
 235         if (unlikely(reg == SDHCI_HOST_VERSION)) {
 236                 u16 val = readw(host->ioaddr + (reg ^ 2));
 237                 /*
 238                  * uSDHC supports SDHCI v3.0, but it's encoded as value
 239                  * 0x3 in host controller version register, which violates
 240                  * SDHCI_SPEC_300 definition.  Work it around here.
 241                  */
 242                 if ((val & SDHCI_SPEC_VER_MASK) == 3)
 243                         return --val;
 244         }
 245
 246         return readw(host->ioaddr + reg);
 247 }
 248
 249 static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 250 {
 251         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 252         struct pltfm_imx_data *imx_data = pltfm_host->priv;
 253
 254         switch (reg) {
 255         case SDHCI_TRANSFER_MODE:
 256                 /*
 257                  * Postpone this write, we must do it together with a
 258                  * command write that is down below.
 259                  */
 260                 if ((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
 261                                 && (host->cmd->opcode == SD_IO_RW_EXTENDED)
 262                                 && (host->cmd->data->blocks > 1)
 263                                 && (host->cmd->data->flags & MMC_DATA_READ)) {
 264                         u32 v;
 265                         v = readl(host->ioaddr + SDHCI_VENDOR_SPEC);
 266                         v |= SDHCI_VENDOR_SPEC_SDIO_QUIRK;
 267                         writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
 268                 }
 269                 imx_data->scratchpad = val;
 270                 return;
 271         case SDHCI_COMMAND:
 272                 if ((host->cmd->opcode == MMC_STOP_TRANSMISSION)
 273                         && (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
 274                         val |= SDHCI_CMD_ABORTCMD;
 275
 276                 if (is_imx6q_usdhc(imx_data)) {
 277                         u32 m = readl(host->ioaddr + SDHCI_MIX_CTRL);
 278                         m = imx_data->scratchpad | (m & 0xffff0000);
 279                         writel(m, host->ioaddr + SDHCI_MIX_CTRL);
 280                         writel(val << 16,
 281                                host->ioaddr + SDHCI_TRANSFER_MODE);
 282                 } else {
 283                         writel(val << 16 | imx_data->scratchpad,
 284                                host->ioaddr + SDHCI_TRANSFER_MODE);
 285                 }
 286                 return;
 287         case SDHCI_BLOCK_SIZE:
 288                 val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
 289                 break;
 290         }
 291         esdhc_clrset_le(host, 0xffff, val, reg);
 292 }
 293
 294 static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
 295 {
 296         u32 new_val;
 297
 298         switch (reg) {
 299         case SDHCI_POWER_CONTROL:
 300                 /*
 301                  * FSL put some DMA bits here
 302                  * If your board has a regulator, code should be here
 303                  */
 304                 return;
 305         case SDHCI_HOST_CONTROL:
 306                 /* FSL messed up here, so we can just keep those three */
 307                 new_val = val & (SDHCI_CTRL_LED | \
 308                                 SDHCI_CTRL_4BITBUS | \
 309                                 SDHCI_CTRL_D3CD);
 310                 /* ensure the endianess */
 311                 new_val |= ESDHC_HOST_CONTROL_LE;
 312                 /* DMA mode bits are shifted */
 313                 new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
 314
 315                 esdhc_clrset_le(host, 0xffff, new_val, reg);
 316                 return;
 317         }
 318         esdhc_clrset_le(host, 0xff, val, reg);
 319
 320         /*
 321          * The esdhc has a design violation to SDHC spec which tells
 322          * that software reset should not affect card detection circuit.
 323          * But esdhc clears its SYSCTL register bits [0..2] during the
 324          * software reset.  This will stop those clocks that card detection
 325          * circuit relies on.  To work around it, we turn the clocks on back
 326          * to keep card detection circuit functional.
 327          */
 328         if ((reg == SDHCI_SOFTWARE_RESET) && (val & 1))
 329                 esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL);
 330 }
 331
 332 static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host)
 333 {
 334         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 335
 336         return clk_get_rate(pltfm_host->clk);
 337 }
 338
 339 static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host)
 340 {
 341         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 342
 343         return clk_get_rate(pltfm_host->clk) / 256 / 16;
 344 }
 345
 346 static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host)
 347 {
 348         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 349         struct pltfm_imx_data *imx_data = pltfm_host->priv;
 350         struct esdhc_platform_data *boarddata = &imx_data->boarddata;
 351
 352         switch (boarddata->wp_type) {
 353         case ESDHC_WP_GPIO:
 354                 if (gpio_is_valid(boarddata->wp_gpio))
 355                         return gpio_get_value(boarddata->wp_gpio);
 356         case ESDHC_WP_CONTROLLER:
 357                 return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) &
 358                                SDHCI_WRITE_PROTECT);
 359         case ESDHC_WP_NONE:
 360                 break;
 361         }
 362
 363         return -ENOSYS;
 364 }
 365
 366 static struct sdhci_ops sdhci_esdhc_ops = {
 367         .read_l = esdhc_readl_le,
 368         .read_w = esdhc_readw_le,
 369         .write_l = esdhc_writel_le,
 370         .write_w = esdhc_writew_le,
 371         .write_b = esdhc_writeb_le,
 372         .set_clock = esdhc_set_clock,
 373         .get_max_clock = esdhc_pltfm_get_max_clock,
 374         .get_min_clock = esdhc_pltfm_get_min_clock,
 375         .get_ro = esdhc_pltfm_get_ro,
 376 };
 377
 378 static struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
 379         .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
 380                         | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
 381                         | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
 382                         | SDHCI_QUIRK_BROKEN_CARD_DETECTION,
 383         .ops = &sdhci_esdhc_ops,
 384 };
 385
 386 static irqreturn_t cd_irq(int irq, void *data)
 387 {
 388         struct sdhci_host *sdhost = (struct sdhci_host *)data;
 389
 390         tasklet_schedule(&sdhost->card_tasklet);
 391         return IRQ_HANDLED;
 392 };
 393
 394 #ifdef CONFIG_OF
 395 static int __devinit
 396 sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
 397                          struct esdhc_platform_data *boarddata)
 398 {
 399         struct device_node *np = pdev->dev.of_node;
 400
 401         if (!np)
 402                 return -ENODEV;
 403
 404         if (of_get_property(np, "fsl,card-wired", NULL))
 405                 boarddata->cd_type = ESDHC_CD_PERMANENT;
 406
 407         if (of_get_property(np, "fsl,cd-controller", NULL))
 408                 boarddata->cd_type = ESDHC_CD_CONTROLLER;
 409
 410         if (of_get_property(np, "fsl,wp-controller", NULL))
 411                 boarddata->wp_type = ESDHC_WP_CONTROLLER;
 412
 413         boarddata->cd_gpio = of_get_named_gpio(np, "cd-gpios", 0);
 414         if (gpio_is_valid(boarddata->cd_gpio))
 415                 boarddata->cd_type = ESDHC_CD_GPIO;
 416
 417         boarddata->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
 418         if (gpio_is_valid(boarddata->wp_gpio))
 419                 boarddata->wp_type = ESDHC_WP_GPIO;
 420
 421         return 0;
 422 }
 423 #else
 424 static inline int
 425 sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
 426                          struct esdhc_platform_data *boarddata)
 427 {
 428         return -ENODEV;
 429 }
 430 #endif
 431
 432 static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
 433 {
 434         const struct of_device_id *of_id =
 435                         of_match_device(imx_esdhc_dt_ids, &pdev->dev);
 436         struct sdhci_pltfm_host *pltfm_host;
 437         struct sdhci_host *host;
 438         struct esdhc_platform_data *boarddata;
 439         struct clk *clk;
 440         int err;
 441         struct pltfm_imx_data *imx_data;
 442
 443         host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata);
 444         if (IS_ERR(host))
 445                 return PTR_ERR(host);
 446
 447         pltfm_host = sdhci_priv(host);
 448
 449         imx_data = kzalloc(sizeof(struct pltfm_imx_data), GFP_KERNEL);
 450         if (!imx_data) {
 451                 err = -ENOMEM;
 452                 goto err_imx_data;
 453         }
 454
 455         if (of_id)
 456                 pdev->id_entry = of_id->data;
 457         imx_data->devtype = pdev->id_entry->driver_data;
 458         pltfm_host->priv = imx_data;
 459
 460         clk = clk_get(mmc_dev(host->mmc), NULL);
 461         if (IS_ERR(clk)) {
 462                 dev_err(mmc_dev(host->mmc), "clk err\n");
 463                 err = PTR_ERR(clk);
 464                 goto err_clk_get;
 465         }
 466         clk_enable(clk);
 467         pltfm_host->clk = clk;
 468
 469         if (!is_imx25_esdhc(imx_data))
 470                 host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
 471
 472         if (is_imx25_esdhc(imx_data) || is_imx35_esdhc(imx_data))
 473                 /* Fix errata ENGcm07207 present on i.MX25 and i.MX35 */
 474                 host->quirks |= SDHCI_QUIRK_NO_MULTIBLOCK
 475                         | SDHCI_QUIRK_BROKEN_ADMA;
 476
 477         if (is_imx53_esdhc(imx_data))
 478                 imx_data->flags |= ESDHC_FLAG_MULTIBLK_NO_INT;
 479
 480         /*
 481          * The imx6q ROM code will change the default watermark level setting
 482          * to something insane.  Change it back here.
 483          */
 484         if (is_imx6q_usdhc(imx_data))
 485                 writel(0x08100810, host->ioaddr + SDHCI_WTMK_LVL);
 486
 487         boarddata = &imx_data->boarddata;
 488         if (sdhci_esdhc_imx_probe_dt(pdev, boarddata) < 0) {
 489                 if (!host->mmc->parent->platform_data) {
 490                         dev_err(mmc_dev(host->mmc), "no board data!\n");
 491                         err = -EINVAL;
 492                         goto no_board_data;
 493                 }
 494                 imx_data->boarddata = *((struct esdhc_platform_data *)
 495                                         host->mmc->parent->platform_data);
 496         }
 497
 498         /* write_protect */
 499         if (boarddata->wp_type == ESDHC_WP_GPIO) {
 500                 err = gpio_request_one(boarddata->wp_gpio, GPIOF_IN, "ESDHC_WP");
 501                 if (err) {
 502                         dev_warn(mmc_dev(host->mmc),
 503                                  "no write-protect pin available!\n");
 504                         boarddata->wp_gpio = -EINVAL;
 505                 }
 506         } else {
 507                 boarddata->wp_gpio = -EINVAL;
 508         }
 509
 510         /* card_detect */
 511         if (boarddata->cd_type != ESDHC_CD_GPIO)
 512                 boarddata->cd_gpio = -EINVAL;
 513
 514         switch (boarddata->cd_type) {
 515         case ESDHC_CD_GPIO:
 516                 err = gpio_request_one(boarddata->cd_gpio, GPIOF_IN, "ESDHC_CD");
 517                 if (err) {
 518                         dev_err(mmc_dev(host->mmc),
 519                                 "no card-detect pin available!\n");
 520                         goto no_card_detect_pin;
 521                 }
 522
 523                 err = request_irq(gpio_to_irq(boarddata->cd_gpio), cd_irq,
 524                                  IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
 525                                  mmc_hostname(host->mmc), host);
 526                 if (err) {
 527                         dev_err(mmc_dev(host->mmc), "request irq error\n");
 528                         goto no_card_detect_irq;
 529                 }
 530                 /* fall through */
 531
 532         case ESDHC_CD_CONTROLLER:
 533                 /* we have a working card_detect back */
 534                 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
 535                 break;
 536
 537         case ESDHC_CD_PERMANENT:
 538                 host->mmc->caps = MMC_CAP_NONREMOVABLE;
 539                 break;
 540
 541         case ESDHC_CD_NONE:
 542                 break;
 543         }
 544
 545         err = sdhci_add_host(host);
 546         if (err)
 547                 goto err_add_host;
 548
 549         return 0;
 550
 551 err_add_host:
 552         if (gpio_is_valid(boarddata->cd_gpio))
 553                 free_irq(gpio_to_irq(boarddata->cd_gpio), host);
 554 no_card_detect_irq:
 555         if (gpio_is_valid(boarddata->cd_gpio))
 556                 gpio_free(boarddata->cd_gpio);
 557         if (gpio_is_valid(boarddata->wp_gpio))
 558                 gpio_free(boarddata->wp_gpio);
 559 no_card_detect_pin:
 560 no_board_data:
 561         clk_disable(pltfm_host->clk);
 562         clk_put(pltfm_host->clk);
 563 err_clk_get:
 564         kfree(imx_data);
 565 err_imx_data:
 566         sdhci_pltfm_free(pdev);
 567         return err;
 568 }
 569
 570 static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev)
 571 {
 572         struct sdhci_host *host = platform_get_drvdata(pdev);
 573         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 574         struct pltfm_imx_data *imx_data = pltfm_host->priv;
 575         struct esdhc_platform_data *boarddata = &imx_data->boarddata;
 576         int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
 577
 578         sdhci_remove_host(host, dead);
 579
 580         if (gpio_is_valid(boarddata->wp_gpio))
 581                 gpio_free(boarddata->wp_gpio);
 582
 583         if (gpio_is_valid(boarddata->cd_gpio)) {
 584                 free_irq(gpio_to_irq(boarddata->cd_gpio), host);
 585                 gpio_free(boarddata->cd_gpio);
 586         }
 587
 588         clk_disable(pltfm_host->clk);
 589         clk_put(pltfm_host->clk);
 590         kfree(imx_data);
 591
 592         sdhci_pltfm_free(pdev);
 593
 594         return 0;
 595 }
 596
 597 static struct platform_driver sdhci_esdhc_imx_driver = {
 598         .driver         = {
 599                 .name   = "sdhci-esdhc-imx",
 600                 .owner  = THIS_MODULE,
 601                 .of_match_table = imx_esdhc_dt_ids,
 602                 .pm     = SDHCI_PLTFM_PMOPS,
 603         },
 604         .id_table       = imx_esdhc_devtype,
 605         .probe          = sdhci_esdhc_imx_probe,
 606         .remove         = __devexit_p(sdhci_esdhc_imx_remove),
 607 };
 608
 609 static int __init sdhci_esdhc_imx_init(void)
 610 {
 611         return platform_driver_register(&sdhci_esdhc_imx_driver);
 612 }
 613 module_init(sdhci_esdhc_imx_init);
 614
 615 static void __exit sdhci_esdhc_imx_exit(void)
 616 {
 617         platform_driver_unregister(&sdhci_esdhc_imx_driver);
 618 }
 619 module_exit(sdhci_esdhc_imx_exit);
 620
 621 MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC");
 622 MODULE_AUTHOR("Wolfram Sang <w.sang@pengutronix.de>");
 623 MODULE_LICENSE("GPL v2");