| blob | 67a11a36270ca05c8761e3b339577fe364dda085 |
3 PCI Bus EEH Error Recovery
4 --------------------------
5 Linas Vepstas
6 <linas@austin.ibm.com>
7 12 January 2005
10 Overview:
11 ---------
12 The IBM POWER-based pSeries and iSeries computers include PCI bus
13 controller chips that have extended capabilities for detecting and
14 reporting a large variety of PCI bus error conditions. These features
15 go under the name of "EEH", for "Extended Error Handling". The EEH
16 hardware features allow PCI bus errors to be cleared and a PCI
17 card to be "rebooted", without also having to reboot the operating
18 system.
20 This is in contrast to traditional PCI error handling, where the
21 PCI chip is wired directly to the CPU, and an error would cause
22 a CPU machine-check/check-stop condition, halting the CPU entirely.
23 Another "traditional" technique is to ignore such errors, which
24 can lead to data corruption, both of user data or of kernel data,
25 hung/unresponsive adapters, or system crashes/lockups. Thus,
26 the idea behind EEH is that the operating system can become more
27 reliable and robust by protecting it from PCI errors, and giving
28 the OS the ability to "reboot"/recover individual PCI devices.
30 Future systems from other vendors, based on the PCI-E specification,
31 may contain similar features.
34 Causes of EEH Errors
35 --------------------
36 EEH was originally designed to guard against hardware failure, such
37 as PCI cards dying from heat, humidity, dust, vibration and bad
38 electrical connections. The vast majority of EEH errors seen in
39 "real life" are due to eithr poorly seated PCI cards, or,
40 unfortunately quite commonly, due device driver bugs, device firmware
41 bugs, and sometimes PCI card hardware bugs.
43 The most common software bug, is one that causes the device to
44 attempt to DMA to a location in system memory that has not been
45 reserved for DMA access for that card. This is a powerful feature,
46 as it prevents what; otherwise, would have been silent memory
47 corruption caused by the bad DMA. A number of device driver
48 bugs have been found and fixed in this way over the past few
49 years. Other possible causes of EEH errors include data or
50 address line parity errors (for example, due to poor electrical
51 connectivity due to a poorly seated card), and PCI-X split-completion
52 errors (due to software, device firmware, or device PCI hardware bugs).
53 The vast majority of "true hardware failures" can be cured by
54 physically removing and re-seating the PCI card.
57 Detection and Recovery
58 ----------------------
59 In the following discussion, a generic overview of how to detect
60 and recover from EEH errors will be presented. This is followed
61 by an overview of how the current implementation in the Linux
62 kernel does it. The actual implementation is subject to change,
63 and some of the finer points are still being debated. These
64 may in turn be swayed if or when other architectures implement
65 similar functionality.
67 When a PCI Host Bridge (PHB, the bus controller connecting the
68 PCI bus to the system CPU electronics complex) detects a PCI error
69 condition, it will "isolate" the affected PCI card. Isolation
70 will block all writes (either to the card from the system, or
71 from the card to the system), and it will cause all reads to
72 return all-ff's (0xff, 0xffff, 0xffffffff for 8/16/32-bit reads).
73 This value was chosen because it is the same value you would
74 get if the device was physically unplugged from the slot.
75 This includes access to PCI memory, I/O space, and PCI config
76 space. Interrupts; however, will continued to be delivered.
78 Detection and recovery are performed with the aid of ppc64
79 firmware. The programming interfaces in the Linux kernel
80 into the firmware are referred to as RTAS (Run-Time Abstraction
81 Services). The Linux kernel does not (should not) access
82 the EEH function in the PCI chipsets directly, primarily because
83 there are a number of different chipsets out there, each with
84 different interfaces and quirks. The firmware provides a
85 uniform abstraction layer that will work with all pSeries
86 and iSeries hardware (and be forwards-compatible).
88 If the OS or device driver suspects that a PCI slot has been
89 EEH-isolated, there is a firmware call it can make to determine if
90 this is the case. If so, then the device driver should put itself
91 into a consistent state (given that it won't be able to complete any
92 pending work) and start recovery of the card. Recovery normally
93 would consist of reseting the PCI device (holding the PCI #RST
94 line high for two seconds), followed by setting up the device
95 config space (the base address registers (BAR's), latency timer,
96 cache line size, interrupt line, and so on). This is followed by a
97 reinitialization of the device driver. In a worst-case scenario,
98 the power to the card can be toggled, at least on hot-plug-capable
99 slots. In principle, layers far above the device driver probably
100 do not need to know that the PCI card has been "rebooted" in this
101 way; ideally, there should be at most a pause in Ethernet/disk/USB
102 I/O while the card is being reset.
104 If the card cannot be recovered after three or four resets, the
105 kernel/device driver should assume the worst-case scenario, that the
106 card has died completely, and report this error to the sysadmin.
107 In addition, error messages are reported through RTAS and also through
108 syslogd (/var/log/messages) to alert the sysadmin of PCI resets.
109 The correct way to deal with failed adapters is to use the standard
110 PCI hotplug tools to remove and replace the dead card.
113 Current PPC64 Linux EEH Implementation
114 --------------------------------------
115 At this time, a generic EEH recovery mechanism has been implemented,
116 so that individual device drivers do not need to be modified to support
117 EEH recovery. This generic mechanism piggy-backs on the PCI hotplug
118 infrastructure, and percolates events up through the userspace/udev
119 infrastructure. Followiing is a detailed description of how this is
120 accomplished.
122 EEH must be enabled in the PHB's very early during the boot process,
123 and if a PCI slot is hot-plugged. The former is performed by
124 eeh_init() in arch/ppc64/kernel/eeh.c, and the later by
125 drivers/pci/hotplug/pSeries_pci.c calling in to the eeh.c code.
126 EEH must be enabled before a PCI scan of the device can proceed.
127 Current Power5 hardware will not work unless EEH is enabled;
128 although older Power4 can run with it disabled. Effectively,
129 EEH can no longer be turned off. PCI devices *must* be
130 registered with the EEH code; the EEH code needs to know about
131 the I/O address ranges of the PCI device in order to detect an
132 error. Given an arbitrary address, the routine
133 pci_get_device_by_addr() will find the pci device associated
134 with that address (if any).
136 The default include/asm-ppc64/io.h macros readb(), inb(), insb(),
137 etc. include a check to see if the i/o read returned all-0xff's.
138 If so, these make a call to eeh_dn_check_failure(), which in turn
139 asks the firmware if the all-ff's value is the sign of a true EEH
140 error. If it is not, processing continues as normal. The grand
141 total number of these false alarms or "false positives" can be
142 seen in /proc/ppc64/eeh (subject to change). Normally, almost
143 all of these occur during boot, when the PCI bus is scanned, where
144 a large number of 0xff reads are part of the bus scan procedure.
146 If a frozen slot is detected, code in arch/ppc64/kernel/eeh.c will
147 print a stack trace to syslog (/var/log/messages). This stack trace
148 has proven to be very useful to device-driver authors for finding
149 out at what point the EEH error was detected, as the error itself
150 usually occurs slightly beforehand.
152 Next, it uses the Linux kernel notifier chain/work queue mechanism to
153 allow any interested parties to find out about the failure. Device
154 drivers, or other parts of the kernel, can use
155 eeh_register_notifier(struct notifier_block *) to find out about EEH
156 events. The event will include a pointer to the pci device, the
157 device node and some state info. Receivers of the event can "do as
158 they wish"; the default handler will be described further in this
159 section.
161 To assist in the recovery of the device, eeh.c exports the
162 following functions:
164 rtas_set_slot_reset() -- assert the PCI #RST line for 1/8th of a second
165 rtas_configure_bridge() -- ask firmware to configure any PCI bridges
166 located topologically under the pci slot.
167 eeh_save_bars() and eeh_restore_bars(): save and restore the PCI
168 config-space info for a device and any devices under it.
171 A handler for the EEH notifier_block events is implemented in
172 drivers/pci/hotplug/pSeries_pci.c, called handle_eeh_events().
173 It saves the device BAR's and then calls rpaphp_unconfig_pci_adapter().
174 This last call causes the device driver for the card to be stopped,
175 which causes uevents to go out to user space. This triggers
176 user-space scripts that might issue commands such as "ifdown eth0"
177 for ethernet cards, and so on. This handler then sleeps for 5 seconds,
178 hoping to give the user-space scripts enough time to complete.
179 It then resets the PCI card, reconfigures the device BAR's, and
180 any bridges underneath. It then calls rpaphp_enable_pci_slot(),
181 which restarts the device driver and triggers more user-space
182 events (for example, calling "ifup eth0" for ethernet cards).
185 Device Shutdown and User-Space Events
186 -------------------------------------
187 This section documents what happens when a pci slot is unconfigured,
188 focusing on how the device driver gets shut down, and on how the
189 events get delivered to user-space scripts.
191 Following is an example sequence of events that cause a device driver
192 close function to be called during the first phase of an EEH reset.
193 The following sequence is an example of the pcnet32 device driver.
195 rpa_php_unconfig_pci_adapter (struct slot *) // in rpaphp_pci.c
196 {
197 calls
198 pci_remove_bus_device (struct pci_dev *) // in /drivers/pci/remove.c
199 {
200 calls
201 pci_destroy_dev (struct pci_dev *)
202 {
203 calls
204 device_unregister (&dev->dev) // in /drivers/base/core.c
205 {
206 calls
207 device_del (struct device *)
208 {
209 calls
210 bus_remove_device() // in /drivers/base/bus.c
211 {
212 calls
213 device_release_driver()
214 {
215 calls
216 struct device_driver->remove() which is just
217 pci_device_remove() // in /drivers/pci/pci_driver.c
218 {
219 calls
220 struct pci_driver->remove() which is just
221 pcnet32_remove_one() // in /drivers/net/pcnet32.c
222 {
223 calls
224 unregister_netdev() // in /net/core/dev.c
225 {
226 calls
227 dev_close() // in /net/core/dev.c
228 {
229 calls dev->stop();
230 which is just pcnet32_close() // in pcnet32.c
231 {
232 which does what you wanted
233 to stop the device
234 }
235 }
236 }
237 which
238 frees pcnet32 device driver memory
239 }
240 }}}}}}
243 in drivers/pci/pci_driver.c,
244 struct device_driver->remove() is just pci_device_remove()
245 which calls struct pci_driver->remove() which is pcnet32_remove_one()
246 which calls unregister_netdev() (in net/core/dev.c)
247 which calls dev_close() (in net/core/dev.c)
248 which calls dev->stop() which is pcnet32_close()
249 which then does the appropriate shutdown.
251 ---
252 Following is the analogous stack trace for events sent to user-space
253 when the pci device is unconfigured.
255 rpa_php_unconfig_pci_adapter() { // in rpaphp_pci.c
256 calls
257 pci_remove_bus_device (struct pci_dev *) { // in /drivers/pci/remove.c
258 calls
259 pci_destroy_dev (struct pci_dev *) {
260 calls
261 device_unregister (&dev->dev) { // in /drivers/base/core.c
262 calls
263 device_del(struct device * dev) { // in /drivers/base/core.c
264 calls
265 kobject_del() { //in /libs/kobject.c
266 calls
267 kobject_uevent() { // in /libs/kobject.c
268 calls
269 kset_uevent() { // in /lib/kobject.c
270 calls
271 kset->uevent_ops->uevent() // which is really just
272 a call to
273 dev_uevent() { // in /drivers/base/core.c
274 calls
275 dev->bus->uevent() which is really just a call to
276 pci_uevent () { // in drivers/pci/hotplug.c
277 which prints device name, etc....
278 }
279 }
280 then kobject_uevent() sends a netlink uevent to userspace
281 --> userspace uevent
282 (during early boot, nobody listens to netlink events and
283 kobject_uevent() executes uevent_helper[], which runs the
284 event process /sbin/hotplug)
285 }
286 }
287 kobject_del() then calls sysfs_remove_dir(), which would
288 trigger any user-space daemon that was watching /sysfs,
289 and notice the delete event.
292 Pro's and Con's of the Current Design
293 -------------------------------------
294 There are several issues with the current EEH software recovery design,
295 which may be addressed in future revisions. But first, note that the
296 big plus of the current design is that no changes need to be made to
297 individual device drivers, so that the current design throws a wide net.
298 The biggest negative of the design is that it potentially disturbs
299 network daemons and file systems that didn't need to be disturbed.
301 -- A minor complaint is that resetting the network card causes
302 user-space back-to-back ifdown/ifup burps that potentially disturb
303 network daemons, that didn't need to even know that the pci
304 card was being rebooted.
306 -- A more serious concern is that the same reset, for SCSI devices,
307 causes havoc to mounted file systems. Scripts cannot post-facto
308 unmount a file system without flushing pending buffers, but this
309 is impossible, because I/O has already been stopped. Thus,
310 ideally, the reset should happen at or below the block layer,
311 so that the file systems are not disturbed.
313 Reiserfs does not tolerate errors returned from the block device.
314 Ext3fs seems to be tolerant, retrying reads/writes until it does
315 succeed. Both have been only lightly tested in this scenario.
317 The SCSI-generic subsystem already has built-in code for performing
318 SCSI device resets, SCSI bus resets, and SCSI host-bus-adapter
319 (HBA) resets. These are cascaded into a chain of attempted
320 resets if a SCSI command fails. These are completely hidden
321 from the block layer. It would be very natural to add an EEH
322 reset into this chain of events.
324 -- If a SCSI error occurs for the root device, all is lost unless
325 the sysadmin had the foresight to run /bin, /sbin, /etc, /var
326 and so on, out of ramdisk/tmpfs.
329 Conclusions
330 -----------
331 There's forward progress ...