2 * arch/arm/mach-orion5x/dns323-setup.c
4 * Copyright (C) 2007 Herbert Valerio Riedel <hvr@gnu.org>
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU Lesser General Public License as
8 * published by the Free Software Foundation; either version 2 of the
9 * License, or (at your option) any later version.
13 #include <linux/kernel.h>
14 #include <linux/init.h>
15 #include <linux/delay.h>
16 #include <linux/platform_device.h>
17 #include <linux/pci.h>
18 #include <linux/irq.h>
19 #include <linux/mtd/physmap.h>
20 #include <linux/mv643xx_eth.h>
21 #include <linux/leds.h>
22 #include <linux/gpio_keys.h>
23 #include <linux/input.h>
24 #include <linux/i2c.h>
25 #include <linux/ata_platform.h>
26 #include <asm/mach-types.h>
28 #include <asm/mach/arch.h>
29 #include <asm/mach/pci.h>
30 #include <mach/orion5x.h>
34 #define DNS323_GPIO_LED_RIGHT_AMBER 1
35 #define DNS323_GPIO_LED_LEFT_AMBER 2
36 #define DNS323_GPIO_SYSTEM_UP 3
37 #define DNS323_GPIO_LED_POWER1 4
38 #define DNS323_GPIO_LED_POWER2 5
39 #define DNS323_GPIO_OVERTEMP 6
40 #define DNS323_GPIO_RTC 7
41 #define DNS323_GPIO_POWER_OFF 8
42 #define DNS323_GPIO_KEY_POWER 9
43 #define DNS323_GPIO_KEY_RESET 10
45 /****************************************************************************
49 static int __init
dns323_pci_map_irq(struct pci_dev
*dev
, u8 slot
, u8 pin
)
54 * Check for devices with hard-wired IRQs.
56 irq
= orion5x_pci_map_irq(dev
, slot
, pin
);
63 static struct hw_pci dns323_pci __initdata
= {
65 .swizzle
= pci_std_swizzle
,
66 .setup
= orion5x_pci_sys_setup
,
67 .scan
= orion5x_pci_sys_scan_bus
,
68 .map_irq
= dns323_pci_map_irq
,
71 static int __init
dns323_dev_id(void)
75 orion5x_pcie_id(&dev
, &rev
);
80 static int __init
dns323_pci_init(void)
82 /* The 5182 doesn't really use its PCI bus, and initialising PCI
83 * gets in the way of initialising the SATA controller.
85 if (machine_is_dns323() && dns323_dev_id() != MV88F5182_DEV_ID
)
86 pci_common_init(&dns323_pci
);
91 subsys_initcall(dns323_pci_init
);
93 /****************************************************************************
94 * 8MiB NOR flash (Spansion S29GL064M90TFIR4)
96 * Layout as used by D-Link:
97 * 0x00000000-0x00010000 : "MTD1"
98 * 0x00010000-0x00020000 : "MTD2"
99 * 0x00020000-0x001a0000 : "Linux Kernel"
100 * 0x001a0000-0x007d0000 : "File System"
101 * 0x007d0000-0x00800000 : "u-boot"
104 #define DNS323_NOR_BOOT_BASE 0xf4000000
105 #define DNS323_NOR_BOOT_SIZE SZ_8M
107 static struct mtd_partition dns323_partitions
[] = {
115 .offset
= 0x00010000,
117 .name
= "Linux Kernel",
119 .offset
= 0x00020000,
121 .name
= "File System",
123 .offset
= 0x001A0000,
127 .offset
= 0x007d0000,
131 static struct physmap_flash_data dns323_nor_flash_data
= {
133 .parts
= dns323_partitions
,
134 .nr_parts
= ARRAY_SIZE(dns323_partitions
)
137 static struct resource dns323_nor_flash_resource
= {
138 .flags
= IORESOURCE_MEM
,
139 .start
= DNS323_NOR_BOOT_BASE
,
140 .end
= DNS323_NOR_BOOT_BASE
+ DNS323_NOR_BOOT_SIZE
- 1,
143 static struct platform_device dns323_nor_flash
= {
144 .name
= "physmap-flash",
147 .platform_data
= &dns323_nor_flash_data
,
149 .resource
= &dns323_nor_flash_resource
,
153 /****************************************************************************
157 static struct mv643xx_eth_platform_data dns323_eth_data
= {
158 .phy_addr
= MV643XX_ETH_PHY_ADDR(8),
161 /* dns323_parse_hex_*() taken from tsx09-common.c; should a common copy of these
162 * functions be kept somewhere?
164 static int __init
dns323_parse_hex_nibble(char n
)
166 if (n
>= '0' && n
<= '9')
169 if (n
>= 'A' && n
<= 'F')
172 if (n
>= 'a' && n
<= 'f')
178 static int __init
dns323_parse_hex_byte(const char *b
)
183 hi
= dns323_parse_hex_nibble(b
[0]);
184 lo
= dns323_parse_hex_nibble(b
[1]);
186 if (hi
< 0 || lo
< 0)
189 return (hi
<< 4) | lo
;
192 static int __init
dns323_read_mac_addr(void)
198 /* MAC address is stored as a regular ol' string in /dev/mtdblock4
199 * (0x007d0000-0x00800000) starting at offset 196480 (0x2ff80).
201 mac_page
= ioremap(DNS323_NOR_BOOT_BASE
+ 0x7d0000 + 196480, 1024);
205 /* Sanity check the string we're looking at */
206 for (i
= 0; i
< 5; i
++) {
207 if (*(mac_page
+ (i
* 3) + 2) != ':') {
212 for (i
= 0; i
< 6; i
++) {
215 byte
= dns323_parse_hex_byte(mac_page
+ (i
* 3));
224 printk("DNS323: Found ethernet MAC address: ");
225 for (i
= 0; i
< 6; i
++)
226 printk("%.2x%s", addr
[i
], (i
< 5) ? ":" : ".\n");
228 memcpy(dns323_eth_data
.mac_addr
, addr
, 6);
237 /****************************************************************************
238 * GPIO LEDs (simple - doesn't use hardware blinking support)
241 #define ORION_BLINK_HALF_PERIOD 100 /* ms */
243 static int dns323_gpio_blink_set(unsigned gpio
,
244 unsigned long *delay_on
, unsigned long *delay_off
)
246 static int value
= 0;
248 if (!*delay_on
&& !*delay_off
)
249 *delay_on
= *delay_off
= ORION_BLINK_HALF_PERIOD
;
251 if (ORION_BLINK_HALF_PERIOD
== *delay_on
252 && ORION_BLINK_HALF_PERIOD
== *delay_off
) {
254 orion_gpio_set_blink(gpio
, value
);
261 static struct gpio_led dns323_leds
[] = {
263 .name
= "power:blue",
264 .gpio
= DNS323_GPIO_LED_POWER2
,
265 .default_trigger
= "timer",
267 .name
= "right:amber",
268 .gpio
= DNS323_GPIO_LED_RIGHT_AMBER
,
271 .name
= "left:amber",
272 .gpio
= DNS323_GPIO_LED_LEFT_AMBER
,
277 static struct gpio_led_platform_data dns323_led_data
= {
278 .num_leds
= ARRAY_SIZE(dns323_leds
),
280 .gpio_blink_set
= dns323_gpio_blink_set
,
283 static struct platform_device dns323_gpio_leds
= {
287 .platform_data
= &dns323_led_data
,
291 /****************************************************************************
295 static struct gpio_keys_button dns323_buttons
[] = {
298 .gpio
= DNS323_GPIO_KEY_RESET
,
299 .desc
= "Reset Button",
303 .gpio
= DNS323_GPIO_KEY_POWER
,
304 .desc
= "Power Button",
309 static struct gpio_keys_platform_data dns323_button_data
= {
310 .buttons
= dns323_buttons
,
311 .nbuttons
= ARRAY_SIZE(dns323_buttons
),
314 static struct platform_device dns323_button_device
= {
319 .platform_data
= &dns323_button_data
,
323 /*****************************************************************************
326 static struct mv_sata_platform_data dns323_sata_data
= {
330 /****************************************************************************
333 static struct orion5x_mpp_mode dns323_mv88f5181_mpp_modes
[] __initdata
= {
334 { 0, MPP_PCIE_RST_OUTn
},
335 { 1, MPP_GPIO
}, /* right amber LED (sata ch0) */
336 { 2, MPP_GPIO
}, /* left amber LED (sata ch1) */
338 { 4, MPP_GPIO
}, /* power button LED */
339 { 5, MPP_GPIO
}, /* power button LED */
340 { 6, MPP_GPIO
}, /* GMT G751-2f overtemp */
341 { 7, MPP_GPIO
}, /* M41T80 nIRQ/OUT/SQW */
342 { 8, MPP_GPIO
}, /* triggers power off */
343 { 9, MPP_GPIO
}, /* power button switch */
344 { 10, MPP_GPIO
}, /* reset button switch */
357 static struct orion5x_mpp_mode dns323_mv88f5182_mpp_modes
[] __initdata
= {
359 { 1, MPP_GPIO
}, /* right amber LED (sata ch0) */
360 { 2, MPP_GPIO
}, /* left amber LED (sata ch1) */
361 { 3, MPP_GPIO
}, /* system up flag */
362 { 4, MPP_GPIO
}, /* power button LED */
363 { 5, MPP_GPIO
}, /* power button LED */
364 { 6, MPP_GPIO
}, /* GMT G751-2f overtemp */
365 { 7, MPP_GPIO
}, /* M41T80 nIRQ/OUT/SQW */
366 { 8, MPP_GPIO
}, /* triggers power off */
367 { 9, MPP_GPIO
}, /* power button switch */
368 { 10, MPP_GPIO
}, /* reset button switch */
370 { 12, MPP_SATA_LED
},
371 { 13, MPP_SATA_LED
},
372 { 14, MPP_SATA_LED
},
373 { 15, MPP_SATA_LED
},
382 * On the DNS-323 the following devices are attached via I2C:
384 * i2c addr | chip | description
385 * 0x3e | GMT G760Af | fan speed PWM controller
386 * 0x48 | GMT G751-2f | temp. sensor and therm. watchdog (LM75 compatible)
387 * 0x68 | ST M41T80 | RTC w/ alarm
389 static struct i2c_board_info __initdata dns323_i2c_devices
[] = {
391 I2C_BOARD_INFO("g760a", 0x3e),
393 I2C_BOARD_INFO("lm75", 0x48),
395 I2C_BOARD_INFO("m41t80", 0x68),
399 /* DNS-323 rev. A specific power off method */
400 static void dns323a_power_off(void)
402 pr_info("%s: triggering power-off...\n", __func__
);
403 gpio_set_value(DNS323_GPIO_POWER_OFF
, 1);
406 /* DNS-323 rev B specific power off method */
407 static void dns323b_power_off(void)
409 pr_info("%s: triggering power-off...\n", __func__
);
410 /* Pin has to be changed to 1 and back to 0 to do actual power off. */
411 gpio_set_value(DNS323_GPIO_POWER_OFF
, 1);
413 gpio_set_value(DNS323_GPIO_POWER_OFF
, 0);
416 static void __init
dns323_init(void)
418 /* Setup basic Orion functions. Need to be called early. */
421 /* Just to be tricky, the 5182 has a completely different
422 * set of MPP modes to the 5181.
424 if (dns323_dev_id() == MV88F5182_DEV_ID
)
425 orion5x_mpp_conf(dns323_mv88f5182_mpp_modes
);
427 orion5x_mpp_conf(dns323_mv88f5181_mpp_modes
);
428 writel(0, MPP_DEV_CTRL
); /* DEV_D[31:16] */
431 /* setup flash mapping
432 * CS3 holds a 8 MB Spansion S29GL064M90TFIR4
434 orion5x_setup_dev_boot_win(DNS323_NOR_BOOT_BASE
, DNS323_NOR_BOOT_SIZE
);
435 platform_device_register(&dns323_nor_flash
);
437 /* The 5181 power LED is active low and requires
438 * DNS323_GPIO_LED_POWER1 to also be low.
440 if (dns323_dev_id() == MV88F5181_DEV_ID
) {
441 dns323_leds
[0].active_low
= 1;
442 gpio_direction_output(DNS323_GPIO_LED_POWER1
, 0);
445 platform_device_register(&dns323_gpio_leds
);
447 platform_device_register(&dns323_button_device
);
449 i2c_register_board_info(0, dns323_i2c_devices
,
450 ARRAY_SIZE(dns323_i2c_devices
));
453 * Configure peripherals.
455 if (dns323_read_mac_addr() < 0)
456 printk("DNS323: Failed to read MAC address\n");
458 orion5x_ehci0_init();
459 orion5x_eth_init(&dns323_eth_data
);
461 orion5x_uart0_init();
463 /* The 5182 has its SATA controller on-chip, and needs its own little
466 if (dns323_dev_id() == MV88F5182_DEV_ID
)
467 orion5x_sata_init(&dns323_sata_data
);
469 /* The 5182 has flag to indicate the system is up. Without this flag
470 * set, power LED will flash and cannot be controlled via leds-gpio.
472 if (dns323_dev_id() == MV88F5182_DEV_ID
)
473 gpio_set_value(DNS323_GPIO_SYSTEM_UP
, 1);
475 /* Register dns323 specific power-off method */
476 if (gpio_request(DNS323_GPIO_POWER_OFF
, "POWEROFF") != 0 ||
477 gpio_direction_output(DNS323_GPIO_POWER_OFF
, 0) != 0)
478 pr_err("DNS323: failed to setup power-off GPIO\n");
479 if (dns323_dev_id() == MV88F5182_DEV_ID
)
480 pm_power_off
= dns323b_power_off
;
482 pm_power_off
= dns323a_power_off
;
485 /* Warning: D-Link uses a wrong mach-type (=526) in their bootloader */
486 MACHINE_START(DNS323
, "D-Link DNS-323")
487 /* Maintainer: Herbert Valerio Riedel <hvr@gnu.org> */
488 .phys_io
= ORION5X_REGS_PHYS_BASE
,
489 .io_pg_offst
= ((ORION5X_REGS_VIRT_BASE
) >> 18) & 0xFFFC,
490 .boot_params
= 0x00000100,
491 .init_machine
= dns323_init
,
492 .map_io
= orion5x_map_io
,
493 .init_irq
= orion5x_init_irq
,
494 .timer
= &orion5x_timer
,
495 .fixup
= tag_fixup_mem32
,