drivers/net/hp100.h

   1 /*
   2  * hp100.h: Hewlett Packard HP10/100VG ANY LAN ethernet driver for Linux.
   3  *
   4  * $Id: hp100.h,v 1.51 1997/04/08 14:26:42 floeff Exp floeff $
   5  *
   6  * Authors:  Jaroslav Kysela, <perex@pf.jcu.cz>
   7  *           Siegfried Loeffler <floeff@tunix.mathematik.uni-stuttgart.de>
   8  *
   9  * This driver is based on the 'hpfepkt' crynwr packet driver.
  10  *
  11  * This source/code is public free; you can distribute it and/or modify
  12  * it under terms of the GNU General Public License (published by the
  13  * Free Software Foundation) either version two of this License, or any
  14  * later version.
  15  */
  16
  17 /****************************************************************************
  18  *  Hardware Constants
  19  ****************************************************************************/
  20
  21 /*
  22  * Page Identifiers
  23  * (Swap Paging Register, PAGING, bits 3:0, Offset 0x02)
  24  */
  25
  26 #define HP100_PAGE_PERFORMANCE  0x0     /* Page 0 */
  27 #define HP100_PAGE_MAC_ADDRESS  0x1     /* Page 1 */
  28 #define HP100_PAGE_HW_MAP       0x2     /* Page 2 */
  29 #define HP100_PAGE_EEPROM_CTRL  0x3     /* Page 3 */
  30 #define HP100_PAGE_MAC_CTRL     0x4     /* Page 4 */
  31 #define HP100_PAGE_MMU_CFG      0x5     /* Page 5 */
  32 #define HP100_PAGE_ID_MAC_ADDR  0x6     /* Page 6 */
  33 #define HP100_PAGE_MMU_POINTER  0x7     /* Page 7 */
  34
  35
  36 /* Registers that are present on all pages  */
  37
  38 #define HP100_REG_HW_ID         0x00    /* R:  (16) Unique card ID           */
  39 #define HP100_REG_TRACE         0x00    /* W:  (16) Used for debug output    */
  40 #define HP100_REG_PAGING        0x02    /* R:  (16),15:4 Card ID             */
  41                                         /* W:  (16),3:0 Switch pages         */
  42 #define HP100_REG_OPTION_LSW    0x04    /* RW: (16) Select card functions    */
  43 #define HP100_REG_OPTION_MSW    0x06    /* RW: (16) Select card functions    */
  44
  45 /*  Page 0 - Performance  */
  46
  47 #define HP100_REG_IRQ_STATUS    0x08    /* RW: (16) Which ints are pending   */
  48 #define HP100_REG_IRQ_MASK      0x0a    /* RW: (16) Select ints to allow     */
  49 #define HP100_REG_FRAGMENT_LEN  0x0c    /* W: (16)12:0 Current fragment len */
  50 /* Note: For 32 bit systems, fragment len and offset registers are available */
  51 /*       at offset 0x28 and 0x2c, where they can be written as 32bit values. */
  52 #define HP100_REG_OFFSET        0x0e    /* RW: (16)12:0 Offset to start read */
  53 #define HP100_REG_DATA32        0x10    /* RW: (32) I/O mode data port       */
  54 #define HP100_REG_DATA16        0x12    /* RW: WORDs must be read from here  */
  55 #define HP100_REG_TX_MEM_FREE   0x14    /* RD: (32) Amount of free Tx mem    */
  56 #define HP100_REG_TX_PDA_L      0x14    /* W: (32) BM: Ptr to PDL, Low Pri  */
  57 #define HP100_REG_TX_PDA_H      0x1c    /* W: (32) BM: Ptr to PDL, High Pri */
  58 #define HP100_REG_RX_PKT_CNT    0x18    /* RD: (8) Rx count of pkts on card  */
  59 #define HP100_REG_TX_PKT_CNT    0x19    /* RD: (8) Tx count of pkts on card  */
  60 #define HP100_REG_RX_PDL        0x1a    /* R: (8) BM: # rx pdl not executed */
  61 #define HP100_REG_TX_PDL        0x1b    /* R: (8) BM: # tx pdl not executed */
  62 #define HP100_REG_RX_PDA        0x18    /* W: (32) BM: Up to 31 addresses */
  63                                         /*             which point to a PDL */
  64 #define HP100_REG_SL_EARLY      0x1c    /*    (32) Enhanced Slave Early Rx */
  65 #define HP100_REG_STAT_DROPPED  0x20    /* R (12) Dropped Packet Counter */
  66 #define HP100_REG_STAT_ERRORED  0x22    /* R (8) Errored Packet Counter */
  67 #define HP100_REG_STAT_ABORT    0x23    /* R (8) Abort Counter/OW Coll. Flag */
  68 #define HP100_REG_RX_RING       0x24    /* W (32) Slave: RX Ring Pointers */
  69 #define HP100_REG_32_FRAGMENT_LEN 0x28  /* W (13) Slave: Fragment Length Reg */
  70 #define HP100_REG_32_OFFSET     0x2c    /* W (16) Slave: Offset Register */
  71
  72 /*  Page 1 - MAC Address/Hash Table  */
  73
  74 #define HP100_REG_MAC_ADDR      0x08    /* RW: (8) Cards MAC address         */
  75 #define HP100_REG_HASH_BYTE0    0x10    /* RW: (8) Cards multicast filter    */
  76
  77 /*  Page 2 - Hardware Mapping  */
  78
  79 #define HP100_REG_MEM_MAP_LSW   0x08    /* RW: (16) LSW of cards mem addr    */
  80 #define HP100_REG_MEM_MAP_MSW   0x0a    /* RW: (16) MSW of cards mem addr    */
  81 #define HP100_REG_IO_MAP        0x0c    /* RW: (8) Cards I/O address         */
  82 #define HP100_REG_IRQ_CHANNEL   0x0d    /* RW: (8) IRQ and edge/level int    */
  83 #define HP100_REG_SRAM          0x0e    /* RW: (8) How much RAM on card      */
  84 #define HP100_REG_BM            0x0f    /* RW: (8) Controls BM functions     */
  85
  86 /* New on Page 2 for ETR chips: */
  87 #define HP100_REG_MODECTRL1     0x10    /* RW: (8) Mode Control 1 */
  88 #define HP100_REG_MODECTRL2     0x11    /* RW: (8) Mode Control 2 */
  89 #define HP100_REG_PCICTRL1      0x12    /* RW: (8) PCI Cfg 1 */
  90 #define HP100_REG_PCICTRL2      0x13    /* RW: (8) PCI Cfg 2 */
  91 #define HP100_REG_PCIBUSMLAT    0x15    /* RW: (8) PCI Bus Master Latency */
  92 #define HP100_REG_EARLYTXCFG    0x16    /* RW: (16) Early TX Cfg/Cntrl Reg */
  93 #define HP100_REG_EARLYRXCFG    0x18    /* RW: (8) Early RX Cfg/Cntrl Reg */
  94 #define HP100_REG_ISAPNPCFG1    0x1a    /* RW: (8) ISA PnP Cfg/Cntrl Reg 1 */
  95 #define HP100_REG_ISAPNPCFG2    0x1b    /* RW: (8) ISA PnP Cfg/Cntrl Reg 2 */
  96
  97 /*  Page 3 - EEPROM/Boot ROM  */
  98
  99 #define HP100_REG_EEPROM_CTRL   0x08    /* RW: (16) Used to load EEPROM      */
 100 #define HP100_REG_BOOTROM_CTRL  0x0a
 101
 102 /*  Page 4 - LAN Configuration  (MAC_CTRL) */
 103
 104 #define HP100_REG_10_LAN_CFG_1  0x08    /* RW: (8) Set 10M XCVR functions   */
 105 #define HP100_REG_10_LAN_CFG_2  0x09    /* RW: (8)     10M XCVR functions   */
 106 #define HP100_REG_VG_LAN_CFG_1  0x0a    /* RW: (8) Set 100M XCVR functions  */
 107 #define HP100_REG_VG_LAN_CFG_2  0x0b    /* RW: (8) 100M LAN Training cfgregs */
 108 #define HP100_REG_MAC_CFG_1     0x0c    /* RW: (8) Types of pkts to accept   */
 109 #define HP100_REG_MAC_CFG_2     0x0d    /* RW: (8) Misc MAC functions        */
 110 #define HP100_REG_MAC_CFG_3     0x0e    /* RW: (8) Misc MAC functions */
 111 #define HP100_REG_MAC_CFG_4     0x0f    /* R:  (8) Misc MAC states */
 112 #define HP100_REG_DROPPED       0x10    /* R:  (16),11:0 Pkts can't fit in mem */
 113 #define HP100_REG_CRC           0x12    /* R:  (8) Pkts with CRC             */
 114 #define HP100_REG_ABORT         0x13    /* R:  (8) Aborted Tx pkts           */
 115 #define HP100_REG_TRAIN_REQUEST 0x14    /* RW: (16) Endnode MAC register. */
 116 #define HP100_REG_TRAIN_ALLOW   0x16    /* R:  (16) Hub allowed register */
 117
 118 /*  Page 5 - MMU  */
 119
 120 #define HP100_REG_RX_MEM_STOP   0x0c    /* RW: (16) End of Rx ring addr      */
 121 #define HP100_REG_TX_MEM_STOP   0x0e    /* RW: (16) End of Tx ring addr      */
 122 #define HP100_REG_PDL_MEM_STOP  0x10    /* Not used by 802.12 devices */
 123 #define HP100_REG_ECB_MEM_STOP  0x14    /* I've no idea what this is */
 124
 125 /*  Page 6 - Card ID/Physical LAN Address  */
 126
 127 #define HP100_REG_BOARD_ID      0x08    /* R:  (8) EISA/ISA card ID          */
 128 #define HP100_REG_BOARD_IO_CHCK 0x0c    /* R:  (8) Added to ID to get FFh    */
 129 #define HP100_REG_SOFT_MODEL    0x0d    /* R:  (8) Config program defined    */
 130 #define HP100_REG_LAN_ADDR      0x10    /* R:  (8) MAC addr of card          */
 131 #define HP100_REG_LAN_ADDR_CHCK 0x16    /* R:  (8) Added to addr to get FFh  */
 132
 133 /*  Page 7 - MMU Current Pointers  */
 134
 135 #define HP100_REG_PTR_RXSTART   0x08    /* R:  (16) Current begin of Rx ring */
 136 #define HP100_REG_PTR_RXEND     0x0a    /* R:  (16) Current end of Rx ring   */
 137 #define HP100_REG_PTR_TXSTART   0x0c    /* R:  (16) Current begin of Tx ring */
 138 #define HP100_REG_PTR_TXEND     0x0e    /* R:  (16) Current end of Rx ring   */
 139 #define HP100_REG_PTR_RPDLSTART 0x10
 140 #define HP100_REG_PTR_RPDLEND   0x12
 141 #define HP100_REG_PTR_RINGPTRS  0x14
 142 #define HP100_REG_PTR_MEMDEBUG  0x1a
 143 /* ------------------------------------------------------------------------ */
 144
 145
 146 /*
 147  * Hardware ID Register I (Always available, HW_ID, Offset 0x00)
 148  */
 149 #define HP100_HW_ID_CASCADE     0x4850  /* Identifies Cascade Chip */
 150
 151 /*
 152  * Hardware ID Register 2 & Paging Register
 153  * (Always available, PAGING, Offset 0x02)
 154  * Bits 15:4 are for the Chip ID
 155  */
 156 #define HP100_CHIPID_MASK        0xFFF0
 157 #define HP100_CHIPID_SHASTA      0x5350 /* Not 802.12 compliant */
 158                                          /* EISA BM/SL, MCA16/32 SL, ISA SL */
 159 #define HP100_CHIPID_RAINIER     0x5360 /* Not 802.12 compliant EISA BM, */
 160                                          /* PCI SL, MCA16/32 SL, ISA SL */
 161 #define HP100_CHIPID_LASSEN      0x5370 /* 802.12 compliant PCI BM, PCI SL */
 162                                          /* LRF supported */
 163
 164 /*
 165  *  Option Registers I and II
 166  * (Always available, OPTION_LSW, Offset 0x04-0x05)
 167  */
 168 #define HP100_DEBUG_EN          0x8000  /* 0:Dis., 1:Enable Debug Dump Ptr. */
 169 #define HP100_RX_HDR            0x4000  /* 0:Dis., 1:Enable putting pkt into */
 170                                         /*   system mem. before Rx interrupt */
 171 #define HP100_MMAP_DIS          0x2000  /* 0:Enable, 1:Disable mem.mapping. */
 172                                         /*   MMAP_DIS must be 0 and MEM_EN */
 173                                         /*   must be 1 for memory-mapped */
 174                                         /*   mode to be enabled */
 175 #define HP100_EE_EN             0x1000  /* 0:Disable,1:Enable EEPROM writing */
 176 #define HP100_BM_WRITE          0x0800  /* 0:Slave, 1:Bus Master for Tx data */
 177 #define HP100_BM_READ           0x0400  /* 0:Slave, 1:Bus Master for Rx data */
 178 #define HP100_TRI_INT           0x0200  /* 0:Don't, 1:Do tri-state the int */
 179 #define HP100_MEM_EN            0x0040  /* Config program set this to */
 180                                         /*   0:Disable, 1:Enable mem map. */
 181                                         /*   See MMAP_DIS. */
 182 #define HP100_IO_EN             0x0020  /* 1:Enable I/O transfers */
 183 #define HP100_BOOT_EN           0x0010  /* 1:Enable boot ROM access */
 184 #define HP100_FAKE_INT          0x0008  /* 1:int */
 185 #define HP100_INT_EN            0x0004  /* 1:Enable ints from card */
 186 #define HP100_HW_RST            0x0002  /* 0:Reset, 1:Out of reset */
 187                                         /* NIC reset on 0 to 1 transition */
 188
 189 /*
 190  *  Option Register III
 191  * (Always available, OPTION_MSW, Offset 0x06)
 192  */
 193 #define HP100_PRIORITY_TX       0x0080  /* 1:Do all Tx pkts as priority */
 194 #define HP100_EE_LOAD           0x0040  /* 1:EEPROM loading, 0 when done */
 195 #define HP100_ADV_NXT_PKT       0x0004  /* 1:Advance to next pkt in Rx queue */
 196                                         /*   h/w will set to 0 when done */
 197 #define HP100_TX_CMD            0x0002  /* 1:Tell h/w download done, h/w */
 198                                         /*   will set to 0 when done */
 199
 200 /*
 201  * Interrupt Status Registers I and II
 202  * (Page PERFORMANCE, IRQ_STATUS, Offset 0x08-0x09)
 203  * Note: With old chips, these Registers will clear when 1 is written to them
 204  *       with new chips this depends on setting of CLR_ISMODE
 205  */
 206 #define HP100_RX_EARLY_INT      0x2000
 207 #define HP100_RX_PDA_ZERO       0x1000
 208 #define HP100_RX_PDL_FILL_COMPL 0x0800
 209 #define HP100_RX_PACKET         0x0400  /* 0:No, 1:Yes pkt has been Rx */
 210 #define HP100_RX_ERROR          0x0200  /* 0:No, 1:Yes Rx pkt had error */
 211 #define HP100_TX_PDA_ZERO       0x0020  /* 1 when PDA count goes to zero */
 212 #define HP100_TX_SPACE_AVAIL    0x0010  /* 0:<8192, 1:>=8192 Tx free bytes */
 213 #define HP100_TX_COMPLETE       0x0008  /* 0:No, 1:Yes a Tx has completed */
 214 #define HP100_MISC_ERROR        0x0004  /* 0:No, 1:Lan Link down or bus error */
 215 #define HP100_TX_ERROR          0x0002  /* 0:No, 1:Yes Tx pkt had error */
 216
 217 /*
 218  * Xmit Memory Free Count
 219  * (Page PERFORMANCE, TX_MEM_FREE, Offset 0x14) (Read only, 32bit)
 220  */
 221 #define HP100_AUTO_COMPARE      0x80000000      /* Tx Space avail & pkts<255 */
 222 #define HP100_FREE_SPACE        0x7fffffe0      /* Tx free memory */
 223
 224 /*
 225  *  IRQ Channel
 226  * (Page HW_MAP, IRQ_CHANNEL, Offset 0x0d)
 227  */
 228 #define HP100_ZERO_WAIT_EN      0x80    /* 0:No, 1:Yes asserts NOWS signal */
 229 #define HP100_IRQ_SCRAMBLE      0x40
 230 #define HP100_BOND_HP           0x20
 231 #define HP100_LEVEL_IRQ         0x10    /* 0:Edge, 1:Level type interrupts. */
 232                                         /* (Only valid on EISA cards) */
 233 #define HP100_IRQMASK           0x0F    /* Isolate the IRQ bits */
 234
 235 /*
 236  * SRAM Parameters
 237  * (Page HW_MAP, SRAM, Offset 0x0e)
 238  */
 239 #define HP100_RAM_SIZE_MASK     0xe0    /* AND to get SRAM size index */
 240 #define HP100_RAM_SIZE_SHIFT    0x05    /* Shift count(put index in lwr bits) */
 241
 242 /*
 243  * Bus Master Register
 244  * (Page HW_MAP, BM, Offset 0x0f)
 245  */
 246 #define HP100_BM_BURST_RD       0x01    /* EISA only: 1=Use burst trans. fm system */
 247                                         /* memory to chip (tx) */
 248 #define HP100_BM_BURST_WR       0x02    /* EISA only: 1=Use burst trans. fm system */
 249                                         /* memory to chip (rx) */
 250 #define HP100_BM_MASTER         0x04    /* 0:Slave, 1:BM mode */
 251 #define HP100_BM_PAGE_CK        0x08    /* This bit should be set whenever in */
 252                                         /* an EISA system */
 253 #define HP100_BM_PCI_8CLK       0x40    /* ... cycles 8 clocks apart */
 254
 255
 256 /*
 257  * Mode Control Register I
 258  * (Page HW_MAP, MODECTRL1, Offset0x10)
 259  */
 260 #define HP100_TX_DUALQ          0x10
 261    /* If set and BM -> dual tx pda queues */
 262 #define HP100_ISR_CLRMODE       0x02    /* If set ISR will clear all pending */
 263                                        /* interrupts on read (etr only?) */
 264 #define HP100_EE_NOLOAD         0x04    /* Status whether res will be loaded */
 265                                        /* from the eeprom */
 266 #define HP100_TX_CNT_FLG        0x08    /* Controls Early TX Reg Cnt Field */
 267 #define HP100_PDL_USE3          0x10    /* If set BM engine will read only */
 268                                        /* first three data elements of a PDL */
 269                                        /* on the first access. */
 270 #define HP100_BUSTYPE_MASK      0xe0    /* Three bit bus type info */
 271
 272 /*
 273  * Mode Control Register II
 274  * (Page HW_MAP, MODECTRL2, Offset0x11)
 275  */
 276 #define HP100_EE_MASK           0x0f    /* Tell EEPROM circuit not to load */
 277                                        /* certain resources */
 278 #define HP100_DIS_CANCEL        0x20    /* For tx dualq mode operation */
 279 #define HP100_EN_PDL_WB         0x40    /* 1: Status of PDL completion may be */
 280                                        /* written back to system mem */
 281 #define HP100_EN_BUS_FAIL       0x80    /* Enables bus-fail portion of misc */
 282                                        /* interrupt */
 283
 284 /*
 285  * PCI Configuration and Control Register I
 286  * (Page HW_MAP, PCICTRL1, Offset 0x12)
 287  */
 288 #define HP100_LO_MEM            0x01    /* 1: Mapped Mem requested below 1MB */
 289 #define HP100_NO_MEM            0x02    /* 1: Disables Req for sysmem to PCI */
 290                                        /* bios */
 291 #define HP100_USE_ISA           0x04    /* 1: isa type decodes will occur */
 292                                        /* simultaneously with PCI decodes */
 293 #define HP100_IRQ_HI_MASK       0xf0    /* pgmed by pci bios */
 294 #define HP100_PCI_IRQ_HI_MASK   0x78    /* Isolate 4 bits for PCI IRQ  */
 295
 296 /*
 297  * PCI Configuration and Control Register II
 298  * (Page HW_MAP, PCICTRL2, Offset 0x13)
 299  */
 300 #define HP100_RD_LINE_PDL       0x01    /* 1: PCI command Memory Read Line en */
 301 #define HP100_RD_TX_DATA_MASK   0x06    /* choose PCI memread cmds for TX */
 302 #define HP100_MWI               0x08    /* 1: en. PCI memory write invalidate */
 303 #define HP100_ARB_MODE          0x10    /* Select PCI arbitor type */
 304 #define HP100_STOP_EN           0x20    /* Enables PCI state machine to issue */
 305                                        /* pci stop if cascade not ready */
 306 #define HP100_IGNORE_PAR        0x40    /* 1: PCI state machine ignores parity */
 307 #define HP100_PCI_RESET         0x80    /* 0->1: Reset PCI block */
 308
 309 /*
 310  * Early TX Configuration and Control Register
 311  * (Page HW_MAP, EARLYTXCFG, Offset 0x16)
 312  */
 313 #define HP100_EN_EARLY_TX       0x8000  /* 1=Enable Early TX */
 314 #define HP100_EN_ADAPTIVE       0x4000  /* 1=Enable adaptive mode */
 315 #define HP100_EN_TX_UR_IRQ      0x2000  /* reserved, must be 0 */
 316 #define HP100_EN_LOW_TX         0x1000  /* reserved, must be 0 */
 317 #define HP100_ET_CNT_MASK       0x0fff  /* bits 11..0: ET counters */
 318
 319 /*
 320  * Early RX Configuration and Control Register
 321  * (Page HW_MAP, EARLYRXCFG, Offset 0x18)
 322  */
 323 #define HP100_EN_EARLY_RX       0x80    /* 1=Enable Early RX */
 324 #define HP100_EN_LOW_RX         0x40    /* reserved, must be 0 */
 325 #define HP100_RX_TRIP_MASK      0x1f    /* bits 4..0: threshold at which the
 326                                          * early rx circuit will start the
 327                                          * dma of received packet into system
 328                                          * memory for BM */
 329
 330 /*
 331  *  Serial Devices Control Register
 332  * (Page EEPROM_CTRL, EEPROM_CTRL, Offset 0x08)
 333  */
 334 #define HP100_EEPROM_LOAD       0x0001  /* 0->1 loads EEPROM into registers. */
 335                                         /* When it goes back to 0, load is   */
 336                                         /* complete. This should take ~600us. */
 337
 338 /*
 339  * 10MB LAN Control and Configuration Register I
 340  * (Page MAC_CTRL, 10_LAN_CFG_1, Offset 0x08)
 341  */
 342 #define HP100_MAC10_SEL         0xc0    /* Get bits to indicate MAC */
 343 #define HP100_AUI_SEL           0x20    /* Status of AUI selection */
 344 #define HP100_LOW_TH            0x10    /* 0:No, 1:Yes allow better cabling */
 345 #define HP100_LINK_BEAT_DIS     0x08    /* 0:Enable, 1:Disable link beat */
 346 #define HP100_LINK_BEAT_ST      0x04    /* 0:No, 1:Yes link beat being Rx */
 347 #define HP100_R_ROL_ST          0x02    /* 0:No, 1:Yes Rx twisted pair has */
 348                                         /*             been reversed */
 349 #define HP100_AUI_ST            0x01    /* 0:No, 1:Yes use AUI on TP card */
 350
 351 /*
 352  * 10 MB LAN Control and Configuration Register II
 353  * (Page MAC_CTRL, 10_LAN_CFG_2, Offset 0x09)
 354  */
 355 #define HP100_SQU_ST            0x01    /* 0:No, 1:Yes collision signal sent */
 356                                         /*       after Tx.Only used for AUI. */
 357 #define HP100_FULLDUP           0x02    /* 1: LXT901 XCVR fullduplx enabled */
 358 #define HP100_DOT3_MAC          0x04    /* 1: DOT 3 Mac sel. unless Autosel */
 359
 360 /*
 361  * MAC Selection, use with MAC10_SEL bits
 362  */
 363 #define HP100_AUTO_SEL_10       0x0     /* Auto select */
 364 #define HP100_XCVR_LXT901_10    0x1     /* LXT901 10BaseT transceiver */
 365 #define HP100_XCVR_7213         0x2     /* 7213 transceiver */
 366 #define HP100_XCVR_82503        0x3     /* 82503 transceiver */
 367
 368 /*
 369  *  100MB LAN Training Register
 370  * (Page MAC_CTRL, VG_LAN_CFG_2, Offset 0x0b) (old, pre 802.12)
 371  */
 372 #define HP100_FRAME_FORMAT      0x08    /* 0:802.3, 1:802.5 frames */
 373 #define HP100_BRIDGE            0x04    /* 0:No, 1:Yes tell hub i am a bridge */
 374 #define HP100_PROM_MODE         0x02    /* 0:No, 1:Yes tell hub card is */
 375                                         /*         promiscuous */
 376 #define HP100_REPEATER          0x01    /* 0:No, 1:Yes tell hub MAC wants to */
 377                                         /*         be a cascaded repeater */
 378
 379 /*
 380  * 100MB LAN Control and Configuration Register
 381  * (Page MAC_CTRL, VG_LAN_CFG_1, Offset 0x0a)
 382  */
 383 #define HP100_VG_SEL            0x80    /* 0:No, 1:Yes use 100 Mbit MAC */
 384 #define HP100_LINK_UP_ST        0x40    /* 0:No, 1:Yes endnode logged in */
 385 #define HP100_LINK_CABLE_ST     0x20    /* 0:No, 1:Yes cable can hear tones */
 386                                         /*         from  hub */
 387 #define HP100_LOAD_ADDR         0x10    /* 0->1 card addr will be sent  */
 388                                         /* 100ms later the link status  */
 389                                         /* bits are valid */
 390 #define HP100_LINK_CMD          0x08    /* 0->1 link will attempt to log in. */
 391                                         /* 100ms later the link status */
 392                                         /* bits are valid */
 393 #define HP100_TRN_DONE          0x04    /* NEW ETR-Chips only: Will be reset */
 394                                         /* after LinkUp Cmd is given and set */
 395                                         /* when training has completed. */
 396 #define HP100_LINK_GOOD_ST      0x02    /* 0:No, 1:Yes cable passed training */
 397 #define HP100_VG_RESET          0x01    /* 0:Yes, 1:No reset the 100VG MAC */
 398
 399
 400 /*
 401  *  MAC Configuration Register I
 402  * (Page MAC_CTRL, MAC_CFG_1, Offset 0x0c)
 403  */
 404 #define HP100_RX_IDLE           0x80    /* 0:Yes, 1:No currently receiving pkts */
 405 #define HP100_TX_IDLE           0x40    /* 0:Yes, 1:No currently Txing pkts */
 406 #define HP100_RX_EN             0x20    /* 1: allow receiving of pkts */
 407 #define HP100_TX_EN             0x10    /* 1: allow transmitting of pkts */
 408 #define HP100_ACC_ERRORED       0x08    /* 0:No, 1:Yes allow Rx of errored pkts */
 409 #define HP100_ACC_MC            0x04    /* 0:No, 1:Yes allow Rx of multicast pkts */
 410 #define HP100_ACC_BC            0x02    /* 0:No, 1:Yes allow Rx of broadcast pkts */
 411 #define HP100_ACC_PHY           0x01    /* 0:No, 1:Yes allow Rx of ALL phys. pkts */
 412 #define HP100_MAC1MODEMASK      0xf0    /* Hide ACC bits */
 413 #define HP100_MAC1MODE1         0x00    /* Receive nothing, must also disable RX */
 414 #define HP100_MAC1MODE2         0x00
 415 #define HP100_MAC1MODE3         HP100_MAC1MODE2 | HP100_ACC_BC
 416 #define HP100_MAC1MODE4         HP100_MAC1MODE3 | HP100_ACC_MC
 417 #define HP100_MAC1MODE5         HP100_MAC1MODE4 /* set mc hash to all ones also */
 418 #define HP100_MAC1MODE6         HP100_MAC1MODE5 | HP100_ACC_PHY /* Promiscuous */
 419 /* Note MODE6 will receive all GOOD packets on the LAN. This really needs
 420    a mode 7 defined to be LAN Analyzer mode, which will receive errored and
 421    runt packets, and keep the CRC bytes. */
 422 #define HP100_MAC1MODE7         HP100_MAC1MODE6 | HP100_ACC_ERRORED
 423
 424 /*
 425  *  MAC Configuration Register II
 426  * (Page MAC_CTRL, MAC_CFG_2, Offset 0x0d)
 427  */
 428 #define HP100_TR_MODE           0x80    /* 0:No, 1:Yes support Token Ring formats */
 429 #define HP100_TX_SAME           0x40    /* 0:No, 1:Yes Tx same packet continuous */
 430 #define HP100_LBK_XCVR          0x20    /* 0:No, 1:Yes loopback through MAC & */
 431                                         /*   transceiver */
 432 #define HP100_LBK_MAC           0x10    /* 0:No, 1:Yes loopback through MAC */
 433 #define HP100_CRC_I             0x08    /* 0:No, 1:Yes inhibit CRC on Tx packets */
 434 #define HP100_ACCNA             0x04    /* 1: For 802.5: Accept only token ring
 435                                          * group addr that maches NA mask */
 436 #define HP100_KEEP_CRC          0x02    /* 0:No, 1:Yes keep CRC on Rx packets. */
 437                                         /*   The length will reflect this. */
 438 #define HP100_ACCFA             0x01    /* 1: For 802.5: Accept only functional
 439                                          * addrs that match FA mask (page1) */
 440 #define HP100_MAC2MODEMASK      0x02
 441 #define HP100_MAC2MODE1         0x00
 442 #define HP100_MAC2MODE2         0x00
 443 #define HP100_MAC2MODE3         0x00
 444 #define HP100_MAC2MODE4         0x00
 445 #define HP100_MAC2MODE5         0x00
 446 #define HP100_MAC2MODE6         0x00
 447 #define HP100_MAC2MODE7         KEEP_CRC
 448
 449 /*
 450  * MAC Configuration Register III
 451  * (Page MAC_CTRL, MAC_CFG_3, Offset 0x0e)
 452  */
 453 #define HP100_PACKET_PACE       0x03    /* Packet Pacing:
 454                                          * 00: No packet pacing
 455                                          * 01: 8 to 16 uS delay
 456                                          * 10: 16 to 32 uS delay
 457                                          * 11: 32 to 64 uS delay
 458                                          */
 459 #define HP100_LRF_EN            0x04    /* 1: External LAN Rcv Filter and
 460                                          * TCP/IP Checksumming enabled. */
 461 #define HP100_AUTO_MODE         0x10    /* 1: AutoSelect between 10/100 */
 462
 463 /*
 464  * MAC Configuration Register IV
 465  * (Page MAC_CTRL, MAC_CFG_4, Offset 0x0f)
 466  */
 467 #define HP100_MAC_SEL_ST        0x01    /* (R): Status of external VGSEL
 468                                          * Signal, 1=100VG, 0=10Mbit sel. */
 469 #define HP100_LINK_FAIL_ST      0x02    /* (R): Status of Link Fail portion
 470                                          * of the Misc. Interrupt */
 471
 472 /*
 473  *  100 MB LAN Training Request/Allowed Registers
 474  * (Page MAC_CTRL, TRAIN_REQUEST and TRAIN_ALLOW, Offset 0x14-0x16)(ETR parts only)
 475  */
 476 #define HP100_MACRQ_REPEATER         0x0001     /* 1: MAC tells HUB it wants to be
 477                                                  *    a cascaded repeater
 478                                                  * 0: ... wants to be a DTE */
 479 #define HP100_MACRQ_PROMSC           0x0006     /* 2 bits: Promiscious mode
 480                                                  * 00: Rcv only unicast packets
 481                                                  *     specifically addr to this
 482                                                  *     endnode
 483                                                  * 10: Rcv all pckts fwded by
 484                                                  *     the local repeater */
 485 #define HP100_MACRQ_FRAMEFMT_EITHER  0x0018     /* 11: either format allowed */
 486 #define HP100_MACRQ_FRAMEFMT_802_3   0x0000     /* 00: 802.3 is requested */
 487 #define HP100_MACRQ_FRAMEFMT_802_5   0x0010     /* 10: 802.5 format is requested */
 488 #define HP100_CARD_MACVER            0xe000     /* R: 3 bit Cards 100VG MAC version */
 489 #define HP100_MALLOW_REPEATER        0x0001     /* If reset, requested access as an
 490                                                  * end node is allowed */
 491 #define HP100_MALLOW_PROMSC          0x0004     /* 2 bits: Promiscious mode
 492                                                  * 00: Rcv only unicast packets
 493                                                  *     specifically addr to this
 494                                                  *     endnode
 495                                                  * 10: Rcv all pckts fwded by
 496                                                  *     the local repeater */
 497 #define HP100_MALLOW_FRAMEFMT        0x00e0     /* 2 bits: Frame Format
 498                                                  * 00: 802.3 format will be used
 499                                                  * 10: 802.5 format will be used */
 500 #define HP100_MALLOW_ACCDENIED       0x0400     /* N bit */
 501 #define HP100_MALLOW_CONFIGURE       0x0f00     /* C bit */
 502 #define HP100_MALLOW_DUPADDR         0x1000     /* D bit */
 503 #define HP100_HUB_MACVER             0xe000     /* R: 3 bit 802.12 MAC/RMAC training */
 504                                              /*    protocol of repeater */
 505
 506 /* ****************************************************************************** */
 507
 508 /*
 509  *  Set/Reset bits
 510  */
 511 #define HP100_SET_HB            0x0100  /* 0:Set fields to 0 whose mask is 1 */
 512 #define HP100_SET_LB            0x0001  /* HB sets upper byte, LB sets lower byte */
 513 #define HP100_RESET_HB          0x0000  /* For readability when resetting bits */
 514 #define HP100_RESET_LB          0x0000  /* For readability when resetting bits */
 515
 516 /*
 517  *  Misc. Constants
 518  */
 519 #define HP100_LAN_100           100     /* lan_type value for VG */
 520 #define HP100_LAN_10            10      /* lan_type value for 10BaseT */
 521 #define HP100_LAN_COAX          9       /* lan_type value for Coax */
 522 #define HP100_LAN_ERR           (-1)    /* lan_type value for link down */
 523
 524 /*
 525  * Bus Master Data Structures  ----------------------------------------------
 526  */
 527
 528 #define MAX_RX_PDL              30      /* Card limit = 31 */
 529 #define MAX_RX_FRAG             2       /* Don't need more... */
 530 #define MAX_TX_PDL              29
 531 #define MAX_TX_FRAG             2       /* Limit = 31 */
 532
 533 /* Define total PDL area size in bytes (should be 4096) */
 534 /* This is the size of kernel (dma) memory that will be allocated. */
 535 #define MAX_RINGSIZE ((MAX_RX_FRAG*8+4+4)*MAX_RX_PDL+(MAX_TX_FRAG*8+4+4)*MAX_TX_PDL)+16
 536
 537 /* Ethernet Packet Sizes */
 538 #define MIN_ETHER_SIZE          60
 539 #define MAX_ETHER_SIZE          1514    /* Needed for preallocation of */
 540                                         /* skb buffer when busmastering */
 541
 542 /* Tx or Rx Ring Entry */
 543 typedef struct hp100_ring {
 544         u_int *pdl;             /* Address of PDLs PDH, dword before
 545                                  * this address is used for rx hdr */
 546         u_int pdl_paddr;        /* Physical address of PDL */
 547         struct sk_buff *skb;
 548         struct hp100_ring *next;
 549 } hp100_ring_t;
 550
 551
 552
 553 /* Mask for Header Descriptor */
 554 #define HP100_PKT_LEN_MASK      0x1FFF  /* AND with RxLength to get length */
 555
 556
 557 /* Receive Packet Status.  Note, the error bits are only valid if ACC_ERRORED
 558    bit in the MAC Configuration Register 1 is set. */
 559 #define HP100_RX_PRI            0x8000  /* 0:No, 1:Yes packet is priority */
 560 #define HP100_SDF_ERR           0x4000  /* 0:No, 1:Yes start of frame error */
 561 #define HP100_SKEW_ERR          0x2000  /* 0:No, 1:Yes skew out of range */
 562 #define HP100_BAD_SYMBOL_ERR    0x1000  /* 0:No, 1:Yes invalid symbol received */
 563 #define HP100_RCV_IPM_ERR       0x0800  /* 0:No, 1:Yes pkt had an invalid packet */
 564                                         /*   marker */
 565 #define HP100_SYMBOL_BAL_ERR    0x0400  /* 0:No, 1:Yes symbol balance error */
 566 #define HP100_VG_ALN_ERR        0x0200  /* 0:No, 1:Yes non-octet received */
 567 #define HP100_TRUNC_ERR         0x0100  /* 0:No, 1:Yes the packet was truncated */
 568 #define HP100_RUNT_ERR          0x0040  /* 0:No, 1:Yes pkt length < Min Pkt */
 569                                         /*   Length Reg. */
 570 #define HP100_ALN_ERR           0x0010  /* 0:No, 1:Yes align error. */
 571 #define HP100_CRC_ERR           0x0008  /* 0:No, 1:Yes CRC occurred. */
 572
 573 /* The last three bits indicate the type of destination address */
 574
 575 #define HP100_MULTI_ADDR_HASH   0x0006  /* 110: Addr multicast, matched hash */
 576 #define HP100_BROADCAST_ADDR    0x0003  /* x11: Addr broadcast */
 577 #define HP100_MULTI_ADDR_NO_HASH 0x0002 /* 010: Addr multicast, didn't match hash */
 578 #define HP100_PHYS_ADDR_MATCH   0x0001  /* x01: Addr was physical and mine */
 579 #define HP100_PHYS_ADDR_NO_MATCH 0x0000 /* x00: Addr was physical but not mine */
 580
 581 /*
 582  *  macros
 583  */
 584
 585 #define hp100_inb( reg ) \
 586         inb( ioaddr + HP100_REG_##reg )
 587 #define hp100_inw( reg ) \
 588         inw( ioaddr + HP100_REG_##reg )
 589 #define hp100_inl( reg ) \
 590         inl( ioaddr + HP100_REG_##reg )
 591 #define hp100_outb( data, reg ) \
 592         outb( data, ioaddr + HP100_REG_##reg )
 593 #define hp100_outw( data, reg ) \
 594         outw( data, ioaddr + HP100_REG_##reg )
 595 #define hp100_outl( data, reg ) \
 596         outl( data, ioaddr + HP100_REG_##reg )
 597 #define hp100_orb( data, reg ) \
 598         outb( inb( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg )
 599 #define hp100_orw( data, reg ) \
 600         outw( inw( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg )
 601 #define hp100_andb( data, reg ) \
 602         outb( inb( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg )
 603 #define hp100_andw( data, reg ) \
 604         outw( inw( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg )
 605
 606 #define hp100_page( page ) \
 607         outw( HP100_PAGE_##page, ioaddr + HP100_REG_PAGING )
 608 #define hp100_ints_off() \
 609         outw( HP100_INT_EN | HP100_RESET_LB, ioaddr + HP100_REG_OPTION_LSW )
 610 #define hp100_ints_on() \
 611         outw( HP100_INT_EN | HP100_SET_LB, ioaddr + HP100_REG_OPTION_LSW )
 612 #define hp100_mem_map_enable() \
 613         outw( HP100_MMAP_DIS | HP100_RESET_HB, ioaddr + HP100_REG_OPTION_LSW )
 614 #define hp100_mem_map_disable() \
 615         outw( HP100_MMAP_DIS | HP100_SET_HB, ioaddr + HP100_REG_OPTION_LSW )