2 * include/linux/mfd/wm8994/pdata.h -- Platform data for WM8994
4 * Copyright 2009 Wolfson Microelectronics PLC.
6 * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
8 * This program is free software; you can redistribute it and/or modify it
9 * under the terms of the GNU General Public License as published by the
10 * Free Software Foundation; either version 2 of the License, or (at your
11 * option) any later version.
15 #ifndef __MFD_WM8994_PDATA_H__
16 #define __MFD_WM8994_PDATA_H__
18 #define WM8994_NUM_LDO 2
19 #define WM8994_NUM_GPIO 11
21 struct wm8994_ldo_pdata
{
22 /** GPIOs to enable regulator, 0 or less if not available */
26 struct regulator_init_data
*init_data
;
29 #define WM8994_CONFIGURE_GPIO 0x8000
31 #define WM8994_DRC_REGS 5
32 #define WM8994_EQ_REGS 20
33 #define WM8958_MBC_CUTOFF_REGS 20
34 #define WM8958_MBC_COEFF_REGS 48
37 * DRC configurations are specified with a label and a set of register
38 * values to write (the enable bits will be ignored). At runtime an
39 * enumerated control will be presented for each DRC block allowing
40 * the user to choose the configration to use.
42 * Configurations may be generated by hand or by using the DRC control
43 * panel provided by the WISCE - see http://www.wolfsonmicro.com/wisce/
46 struct wm8994_drc_cfg
{
48 u16 regs
[WM8994_DRC_REGS
];
52 * ReTune Mobile configurations are specified with a label, sample
53 * rate and set of values to write (the enable bits will be ignored).
55 * Configurations are expected to be generated using the ReTune Mobile
56 * control panel in WISCE - see http://www.wolfsonmicro.com/wisce/
58 struct wm8994_retune_mobile_cfg
{
61 u16 regs
[WM8994_EQ_REGS
];
65 * Multiband compressor configurations are specified with a label and
66 * two sets of values to write. Configurations are expected to be
67 * generated using the multiband compressor configuration panel in
68 * WISCE - see http://www.wolfsonmicro.com/wisce/
70 struct wm8958_mbc_cfg
{
72 u16 cutoff_regs
[WM8958_MBC_CUTOFF_REGS
];
73 u16 coeff_regs
[WM8958_MBC_COEFF_REGS
];
80 * Default values for GPIOs if non-zero, WM8994_CONFIGURE_GPIO
81 * can be used for all zero values.
83 int gpio_defaults
[WM8994_NUM_GPIO
];
85 struct wm8994_ldo_pdata ldo
[WM8994_NUM_LDO
];
87 int irq_base
; /** Base IRQ number for WM8994, required for IRQs */
90 struct wm8994_drc_cfg
*drc_cfgs
;
92 int num_retune_mobile_cfgs
;
93 struct wm8994_retune_mobile_cfg
*retune_mobile_cfgs
;
96 struct wm8958_mbc_cfg
*mbc_cfgs
;
98 /* LINEOUT can be differential or single ended */
99 unsigned int lineout1_diff
:1;
100 unsigned int lineout2_diff
:1;
102 /* Common mode feedback */
103 unsigned int lineout1fb
:1;
104 unsigned int lineout2fb
:1;
106 /* IRQ for microphone detection if brought out directly as a
111 /* Microphone biases: 0=0.9*AVDD1 1=0.65*AVVD1 */
112 unsigned int micbias1_lvl
:1;
113 unsigned int micbias2_lvl
:1;
115 /* Jack detect threashold levels, see datasheet for values */
116 unsigned int jd_scthr
:2;
117 unsigned int jd_thr
:2;