libata: fix oops when LPM is used with PMP

[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / drivers / mtd / nand / atmel_nand.c

/*
 *  Copyright (C) 2003 Rick Bronson
 *
 *  Derived from drivers/mtd/nand/autcpu12.c
 *       Copyright (c) 2001 Thomas Gleixner (gleixner@autronix.de)
 *
 *  Derived from drivers/mtd/spia.c
 *       Copyright (C) 2000 Steven J. Hill (sjhill@cotw.com)
 *
 *
 *  Add Hardware ECC support for AT91SAM9260 / AT91SAM9263
 *     Richard Genoud (richard.genoud@gmail.com), Adeneo Copyright (C) 2007
 *
 *     Derived from Das U-Boot source code
 *              (u-boot-1.1.5/board/atmel/at91sam9263ek/nand.c)
 *     (C) Copyright 2006 ATMEL Rousset, Lacressonniere Nicolas
 *
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 */

#include <linux/slab.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>

#include <linux/gpio.h>
#include <linux/io.h>

#include <mach/board.h>
#include <mach/cpu.h>

#ifdef CONFIG_MTD_NAND_ATMEL_ECC_HW
#define hard_ecc        1
#else
#define hard_ecc        0
#endif

#ifdef CONFIG_MTD_NAND_ATMEL_ECC_NONE
#define no_ecc          1
#else
#define no_ecc          0
#endif

static int on_flash_bbt = 0;
module_param(on_flash_bbt, int, 0);

/* Register access macros */
#define ecc_readl(add, reg)                             \
        __raw_readl(add + ATMEL_ECC_##reg)
#define ecc_writel(add, reg, value)                     \
        __raw_writel((value), add + ATMEL_ECC_##reg)

#include "atmel_nand_ecc.h"     /* Hardware ECC registers */

/* oob layout for large page size
 * bad block info is on bytes 0 and 1
 * the bytes have to be consecutives to avoid
 * several NAND_CMD_RNDOUT during read
 */
static struct nand_ecclayout atmel_oobinfo_large = {
        .eccbytes = 4,
        .eccpos = {60, 61, 62, 63},
        .oobfree = {
                {2, 58}
        },
};

/* oob layout for small page size
 * bad block info is on bytes 4 and 5
 * the bytes have to be consecutives to avoid
 * several NAND_CMD_RNDOUT during read
 */
static struct nand_ecclayout atmel_oobinfo_small = {
        .eccbytes = 4,
        .eccpos = {0, 1, 2, 3},
        .oobfree = {
                {6, 10}
        },
};

struct atmel_nand_host {
        struct nand_chip        nand_chip;
        struct mtd_info         mtd;
        void __iomem            *io_base;
        struct atmel_nand_data  *board;
        struct device           *dev;
        void __iomem            *ecc;
};

/*
 * Enable NAND.
 */
static void atmel_nand_enable(struct atmel_nand_host *host)
{
        if (host->board->enable_pin)
                gpio_set_value(host->board->enable_pin, 0);
}

/*
 * Disable NAND.
 */
static void atmel_nand_disable(struct atmel_nand_host *host)
{
        if (host->board->enable_pin)
                gpio_set_value(host->board->enable_pin, 1);
}

/*
 * Hardware specific access to control-lines
 */
static void atmel_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
        struct nand_chip *nand_chip = mtd->priv;
        struct atmel_nand_host *host = nand_chip->priv;

        if (ctrl & NAND_CTRL_CHANGE) {
                if (ctrl & NAND_NCE)
                        atmel_nand_enable(host);
                else
                        atmel_nand_disable(host);
        }
        if (cmd == NAND_CMD_NONE)
                return;

        if (ctrl & NAND_CLE)
                writeb(cmd, host->io_base + (1 << host->board->cle));
        else
                writeb(cmd, host->io_base + (1 << host->board->ale));
}

/*
 * Read the Device Ready pin.
 */
static int atmel_nand_device_ready(struct mtd_info *mtd)
{
        struct nand_chip *nand_chip = mtd->priv;
        struct atmel_nand_host *host = nand_chip->priv;

        return gpio_get_value(host->board->rdy_pin) ^
                !!host->board->rdy_pin_active_low;
}

/*
 * Minimal-overhead PIO for data access.
 */
static void atmel_read_buf(struct mtd_info *mtd, u8 *buf, int len)
{
        struct nand_chip        *nand_chip = mtd->priv;

        __raw_readsb(nand_chip->IO_ADDR_R, buf, len);
}

static void atmel_read_buf16(struct mtd_info *mtd, u8 *buf, int len)
{
        struct nand_chip        *nand_chip = mtd->priv;

        __raw_readsw(nand_chip->IO_ADDR_R, buf, len / 2);
}

static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
{
        struct nand_chip        *nand_chip = mtd->priv;

        __raw_writesb(nand_chip->IO_ADDR_W, buf, len);
}

static void atmel_write_buf16(struct mtd_info *mtd, const u8 *buf, int len)
{
        struct nand_chip        *nand_chip = mtd->priv;

        __raw_writesw(nand_chip->IO_ADDR_W, buf, len / 2);
}

/*
 * Calculate HW ECC
 *
 * function called after a write
 *
 * mtd:        MTD block structure
 * dat:        raw data (unused)
 * ecc_code:   buffer for ECC
 */
static int atmel_nand_calculate(struct mtd_info *mtd,
                const u_char *dat, unsigned char *ecc_code)
{
        struct nand_chip *nand_chip = mtd->priv;
        struct atmel_nand_host *host = nand_chip->priv;
        unsigned int ecc_value;

        /* get the first 2 ECC bytes */
        ecc_value = ecc_readl(host->ecc, PR);

        ecc_code[0] = ecc_value & 0xFF;
        ecc_code[1] = (ecc_value >> 8) & 0xFF;

        /* get the last 2 ECC bytes */
        ecc_value = ecc_readl(host->ecc, NPR) & ATMEL_ECC_NPARITY;

        ecc_code[2] = ecc_value & 0xFF;
        ecc_code[3] = (ecc_value >> 8) & 0xFF;

        return 0;
}

/*
 * HW ECC read page function
 *
 * mtd:        mtd info structure
 * chip:       nand chip info structure
 * buf:        buffer to store read data
 */
static int atmel_nand_read_page(struct mtd_info *mtd,
                struct nand_chip *chip, uint8_t *buf, int page)
{
        int eccsize = chip->ecc.size;
        int eccbytes = chip->ecc.bytes;
        uint32_t *eccpos = chip->ecc.layout->eccpos;
        uint8_t *p = buf;
        uint8_t *oob = chip->oob_poi;
        uint8_t *ecc_pos;
        int stat;

        /*
         * Errata: ALE is incorrectly wired up to the ECC controller
         * on the AP7000, so it will include the address cycles in the
         * ECC calculation.
         *
         * Workaround: Reset the parity registers before reading the
         * actual data.
         */
        if (cpu_is_at32ap7000()) {
                struct atmel_nand_host *host = chip->priv;
                ecc_writel(host->ecc, CR, ATMEL_ECC_RST);
        }

        /* read the page */
        chip->read_buf(mtd, p, eccsize);

        /* move to ECC position if needed */
        if (eccpos[0] != 0) {
                /* This only works on large pages
                 * because the ECC controller waits for
                 * NAND_CMD_RNDOUTSTART after the
                 * NAND_CMD_RNDOUT.
                 * anyway, for small pages, the eccpos[0] == 0
                 */
                chip->cmdfunc(mtd, NAND_CMD_RNDOUT,
                                mtd->writesize + eccpos[0], -1);
        }

        /* the ECC controller needs to read the ECC just after the data */
        ecc_pos = oob + eccpos[0];
        chip->read_buf(mtd, ecc_pos, eccbytes);

        /* check if there's an error */
        stat = chip->ecc.correct(mtd, p, oob, NULL);

        if (stat < 0)
                mtd->ecc_stats.failed++;
        else
                mtd->ecc_stats.corrected += stat;

        /* get back to oob start (end of page) */
        chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1);

        /* read the oob */
        chip->read_buf(mtd, oob, mtd->oobsize);

        return 0;
}

/*
 * HW ECC Correction
 *
 * function called after a read
 *
 * mtd:        MTD block structure
 * dat:        raw data read from the chip
 * read_ecc:   ECC from the chip (unused)
 * isnull:     unused
 *
 * Detect and correct a 1 bit error for a page
 */
static int atmel_nand_correct(struct mtd_info *mtd, u_char *dat,
                u_char *read_ecc, u_char *isnull)
{
        struct nand_chip *nand_chip = mtd->priv;
        struct atmel_nand_host *host = nand_chip->priv;
        unsigned int ecc_status;
        unsigned int ecc_word, ecc_bit;

        /* get the status from the Status Register */
        ecc_status = ecc_readl(host->ecc, SR);

        /* if there's no error */
        if (likely(!(ecc_status & ATMEL_ECC_RECERR)))
                return 0;

        /* get error bit offset (4 bits) */
        ecc_bit = ecc_readl(host->ecc, PR) & ATMEL_ECC_BITADDR;
        /* get word address (12 bits) */
        ecc_word = ecc_readl(host->ecc, PR) & ATMEL_ECC_WORDADDR;
        ecc_word >>= 4;

        /* if there are multiple errors */
        if (ecc_status & ATMEL_ECC_MULERR) {
                /* check if it is a freshly erased block
                 * (filled with 0xff) */
                if ((ecc_bit == ATMEL_ECC_BITADDR)
                                && (ecc_word == (ATMEL_ECC_WORDADDR >> 4))) {
                        /* the block has just been erased, return OK */
                        return 0;
                }
                /* it doesn't seems to be a freshly
                 * erased block.
                 * We can't correct so many errors */
                dev_dbg(host->dev, "atmel_nand : multiple errors detected."
                                " Unable to correct.\n");
                return -EIO;
        }

        /* if there's a single bit error : we can correct it */
        if (ecc_status & ATMEL_ECC_ECCERR) {
                /* there's nothing much to do here.
                 * the bit error is on the ECC itself.
                 */
                dev_dbg(host->dev, "atmel_nand : one bit error on ECC code."
                                " Nothing to correct\n");
                return 0;
        }

        dev_dbg(host->dev, "atmel_nand : one bit error on data."
                        " (word offset in the page :"
                        " 0x%x bit offset : 0x%x)\n",
                        ecc_word, ecc_bit);
        /* correct the error */
        if (nand_chip->options & NAND_BUSWIDTH_16) {
                /* 16 bits words */
                ((unsigned short *) dat)[ecc_word] ^= (1 << ecc_bit);
        } else {
                /* 8 bits words */
                dat[ecc_word] ^= (1 << ecc_bit);
        }
        dev_dbg(host->dev, "atmel_nand : error corrected\n");
        return 1;
}

/*
 * Enable HW ECC : unused on most chips
 */
static void atmel_nand_hwctl(struct mtd_info *mtd, int mode)
{
        if (cpu_is_at32ap7000()) {
                struct nand_chip *nand_chip = mtd->priv;
                struct atmel_nand_host *host = nand_chip->priv;
                ecc_writel(host->ecc, CR, ATMEL_ECC_RST);
        }
}

#ifdef CONFIG_MTD_CMDLINE_PARTS
static const char *part_probes[] = { "cmdlinepart", NULL };
#endif

/*
 * Probe for the NAND device.
 */
static int __init atmel_nand_probe(struct platform_device *pdev)
{
        struct atmel_nand_host *host;
        struct mtd_info *mtd;
        struct nand_chip *nand_chip;
        struct resource *regs;
        struct resource *mem;
        int res;

#ifdef CONFIG_MTD_PARTITIONS
        struct mtd_partition *partitions = NULL;
        int num_partitions = 0;
#endif

        mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
        if (!mem) {
                printk(KERN_ERR "atmel_nand: can't get I/O resource mem\n");
                return -ENXIO;
        }

        /* Allocate memory for the device structure (and zero it) */
        host = kzalloc(sizeof(struct atmel_nand_host), GFP_KERNEL);
        if (!host) {
                printk(KERN_ERR "atmel_nand: failed to allocate device structure.\n");
                return -ENOMEM;
        }

        host->io_base = ioremap(mem->start, mem->end - mem->start + 1);
        if (host->io_base == NULL) {
                printk(KERN_ERR "atmel_nand: ioremap failed\n");
                res = -EIO;
                goto err_nand_ioremap;
        }

        mtd = &host->mtd;
        nand_chip = &host->nand_chip;
        host->board = pdev->dev.platform_data;
        host->dev = &pdev->dev;

        nand_chip->priv = host;         /* link the private data structures */
        mtd->priv = nand_chip;
        mtd->owner = THIS_MODULE;

        /* Set address of NAND IO lines */
        nand_chip->IO_ADDR_R = host->io_base;
        nand_chip->IO_ADDR_W = host->io_base;
        nand_chip->cmd_ctrl = atmel_nand_cmd_ctrl;

        if (host->board->rdy_pin)
                nand_chip->dev_ready = atmel_nand_device_ready;

        regs = platform_get_resource(pdev, IORESOURCE_MEM, 1);
        if (!regs && hard_ecc) {
                printk(KERN_ERR "atmel_nand: can't get I/O resource "
                                "regs\nFalling back on software ECC\n");
        }

        nand_chip->ecc.mode = NAND_ECC_SOFT;    /* enable ECC */
        if (no_ecc)
                nand_chip->ecc.mode = NAND_ECC_NONE;
        if (hard_ecc && regs) {
                host->ecc = ioremap(regs->start, regs->end - regs->start + 1);
                if (host->ecc == NULL) {
                        printk(KERN_ERR "atmel_nand: ioremap failed\n");
                        res = -EIO;
                        goto err_ecc_ioremap;
                }
                nand_chip->ecc.mode = NAND_ECC_HW;
                nand_chip->ecc.calculate = atmel_nand_calculate;
                nand_chip->ecc.correct = atmel_nand_correct;
                nand_chip->ecc.hwctl = atmel_nand_hwctl;
                nand_chip->ecc.read_page = atmel_nand_read_page;
                nand_chip->ecc.bytes = 4;
        }

        nand_chip->chip_delay = 20;             /* 20us command delay time */

        if (host->board->bus_width_16) {        /* 16-bit bus width */
                nand_chip->options |= NAND_BUSWIDTH_16;
                nand_chip->read_buf = atmel_read_buf16;
                nand_chip->write_buf = atmel_write_buf16;
        } else {
                nand_chip->read_buf = atmel_read_buf;
                nand_chip->write_buf = atmel_write_buf;
        }

        platform_set_drvdata(pdev, host);
        atmel_nand_enable(host);

        if (host->board->det_pin) {
                if (gpio_get_value(host->board->det_pin)) {
                        printk(KERN_INFO "No SmartMedia card inserted.\n");
                        res = -ENXIO;
                        goto err_no_card;
                }
        }

        if (on_flash_bbt) {
                printk(KERN_INFO "atmel_nand: Use On Flash BBT\n");
                nand_chip->options |= NAND_USE_FLASH_BBT;
        }

        /* first scan to find the device and get the page size */
        if (nand_scan_ident(mtd, 1, NULL)) {
                res = -ENXIO;
                goto err_scan_ident;
        }

        if (nand_chip->ecc.mode == NAND_ECC_HW) {
                /* ECC is calculated for the whole page (1 step) */
                nand_chip->ecc.size = mtd->writesize;

                /* set ECC page size and oob layout */
                switch (mtd->writesize) {
                case 512:
                        nand_chip->ecc.layout = &atmel_oobinfo_small;
                        ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_528);
                        break;
                case 1024:
                        nand_chip->ecc.layout = &atmel_oobinfo_large;
                        ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_1056);
                        break;
                case 2048:
                        nand_chip->ecc.layout = &atmel_oobinfo_large;
                        ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_2112);
                        break;
                case 4096:
                        nand_chip->ecc.layout = &atmel_oobinfo_large;
                        ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_4224);
                        break;
                default:
                        /* page size not handled by HW ECC */
                        /* switching back to soft ECC */
                        nand_chip->ecc.mode = NAND_ECC_SOFT;
                        nand_chip->ecc.calculate = NULL;
                        nand_chip->ecc.correct = NULL;
                        nand_chip->ecc.hwctl = NULL;
                        nand_chip->ecc.read_page = NULL;
                        nand_chip->ecc.postpad = 0;
                        nand_chip->ecc.prepad = 0;
                        nand_chip->ecc.bytes = 0;
                        break;
                }
        }

        /* second phase scan */
        if (nand_scan_tail(mtd)) {
                res = -ENXIO;
                goto err_scan_tail;
        }

#ifdef CONFIG_MTD_PARTITIONS
#ifdef CONFIG_MTD_CMDLINE_PARTS
        mtd->name = "atmel_nand";
        num_partitions = parse_mtd_partitions(mtd, part_probes,
                                              &partitions, 0);
#endif
        if (num_partitions <= 0 && host->board->partition_info)
                partitions = host->board->partition_info(mtd->size,
                                                         &num_partitions);

        if ((!partitions) || (num_partitions == 0)) {
                printk(KERN_ERR "atmel_nand: No partitions defined, or unsupported device.\n");
                res = -ENXIO;
                goto err_no_partitions;
        }

        res = add_mtd_partitions(mtd, partitions, num_partitions);
#else
        res = add_mtd_device(mtd);
#endif

        if (!res)
                return res;

#ifdef CONFIG_MTD_PARTITIONS
err_no_partitions:
#endif
        nand_release(mtd);
err_scan_tail:
err_scan_ident:
err_no_card:
        atmel_nand_disable(host);
        platform_set_drvdata(pdev, NULL);
        if (host->ecc)
                iounmap(host->ecc);
err_ecc_ioremap:
        iounmap(host->io_base);
err_nand_ioremap:
        kfree(host);
        return res;
}

/*
 * Remove a NAND device.
 */
static int __exit atmel_nand_remove(struct platform_device *pdev)
{
        struct atmel_nand_host *host = platform_get_drvdata(pdev);
        struct mtd_info *mtd = &host->mtd;

        nand_release(mtd);

        atmel_nand_disable(host);

        if (host->ecc)
                iounmap(host->ecc);
        iounmap(host->io_base);
        kfree(host);

        return 0;
}

static struct platform_driver atmel_nand_driver = {
        .remove         = __exit_p(atmel_nand_remove),
        .driver         = {
                .name   = "atmel_nand",
                .owner  = THIS_MODULE,
        },
};

static int __init atmel_nand_init(void)
{
        return platform_driver_probe(&atmel_nand_driver, atmel_nand_probe);
}


static void __exit atmel_nand_exit(void)
{
        platform_driver_unregister(&atmel_nand_driver);
}


module_init(atmel_nand_init);
module_exit(atmel_nand_exit);

MODULE_LICENSE("GPL");
MODULE_AUTHOR("Rick Bronson");
MODULE_DESCRIPTION("NAND/SmartMedia driver for AT91 / AVR32");
MODULE_ALIAS("platform:atmel_nand");