drivers/usb/core/hcd.h

   1 /*
   2  * Copyright (c) 2001-2002 by David Brownell
   3  *
   4  * This program is free software; you can redistribute it and/or modify it
   5  * under the terms of the GNU General Public License as published by the
   6  * Free Software Foundation; either version 2 of the License, or (at your
   7  * option) any later version.
   8  *
   9  * This program is distributed in the hope that it will be useful, but
  10  * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
  11  * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
  12  * for more details.
  13  *
  14  * You should have received a copy of the GNU General Public License
  15  * along with this program; if not, write to the Free Software Foundation,
  16  * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  17  */
  18
  19
  20 #ifdef __KERNEL__
  21
  22 /* This file contains declarations of usbcore internals that are mostly
  23  * used or exposed by Host Controller Drivers.
  24  */
  25
  26 /*
  27  * USB Packet IDs (PIDs)
  28  */
  29 #define USB_PID_UNDEF_0                 0xf0
  30 #define USB_PID_OUT                     0xe1
  31 #define USB_PID_ACK                     0xd2
  32 #define USB_PID_DATA0                   0xc3
  33 #define USB_PID_PING                    0xb4    /* USB 2.0 */
  34 #define USB_PID_SOF                     0xa5
  35 #define USB_PID_NYET                    0x96    /* USB 2.0 */
  36 #define USB_PID_DATA2                   0x87    /* USB 2.0 */
  37 #define USB_PID_SPLIT                   0x78    /* USB 2.0 */
  38 #define USB_PID_IN                      0x69
  39 #define USB_PID_NAK                     0x5a
  40 #define USB_PID_DATA1                   0x4b
  41 #define USB_PID_PREAMBLE                0x3c    /* Token mode */
  42 #define USB_PID_ERR                     0x3c    /* USB 2.0: handshake mode */
  43 #define USB_PID_SETUP                   0x2d
  44 #define USB_PID_STALL                   0x1e
  45 #define USB_PID_MDATA                   0x0f    /* USB 2.0 */
  46
  47 /*-------------------------------------------------------------------------*/
  48
  49 /*
  50  * USB Host Controller Driver (usb_hcd) framework
  51  *
  52  * Since "struct usb_bus" is so thin, you can't share much code in it.
  53  * This framework is a layer over that, and should be more sharable.
  54  */
  55
  56 /*-------------------------------------------------------------------------*/
  57
  58 struct usb_hcd {        /* usb_bus.hcpriv points to this */
  59
  60         /*
  61          * housekeeping
  62          */
  63         struct usb_bus          self;           /* hcd is-a bus */
  64
  65         const char              *product_desc;  /* product/vendor string */
  66         char                    irq_descr[24];  /* driver + bus # */
  67
  68         struct timer_list       rh_timer;       /* drives root-hub polling */
  69         struct urb              *status_urb;    /* the current status urb */
  70
  71         /*
  72          * hardware info/state
  73          */
  74         const struct hc_driver  *driver;        /* hw-specific hooks */
  75         unsigned                saw_irq : 1;
  76         unsigned                can_wakeup:1;   /* hw supports wakeup? */
  77         unsigned                remote_wakeup:1;/* sw should use wakeup? */
  78         unsigned                rh_registered:1;/* is root hub registered? */
  79
  80         /* The next flag is a stopgap, to be removed when all the HCDs
  81          * support the new root-hub polling mechanism. */
  82         unsigned                uses_new_polling:1;
  83         unsigned                poll_rh:1;      /* poll for rh status? */
  84         unsigned                poll_pending:1; /* status has changed? */
  85
  86         int                     irq;            /* irq allocated */
  87         void __iomem            *regs;          /* device memory/io */
  88         u64                     rsrc_start;     /* memory/io resource start */
  89         u64                     rsrc_len;       /* memory/io resource length */
  90         unsigned                power_budget;   /* in mA, 0 = no limit */
  91
  92 #define HCD_BUFFER_POOLS        4
  93         struct dma_pool         *pool [HCD_BUFFER_POOLS];
  94
  95         int                     state;
  96 #       define  __ACTIVE                0x01
  97 #       define  __SUSPEND               0x04
  98 #       define  __TRANSIENT             0x80
  99
 100 #       define  HC_STATE_HALT           0
 101 #       define  HC_STATE_RUNNING        (__ACTIVE)
 102 #       define  HC_STATE_QUIESCING      (__SUSPEND|__TRANSIENT|__ACTIVE)
 103 #       define  HC_STATE_RESUMING       (__SUSPEND|__TRANSIENT)
 104 #       define  HC_STATE_SUSPENDED      (__SUSPEND)
 105
 106 #define HC_IS_RUNNING(state) ((state) & __ACTIVE)
 107 #define HC_IS_SUSPENDED(state) ((state) & __SUSPEND)
 108
 109         /* more shared queuing code would be good; it should support
 110          * smarter scheduling, handle transaction translators, etc;
 111          * input size of periodic table to an interrupt scheduler.
 112          * (ohci 32, uhci 1024, ehci 256/512/1024).
 113          */
 114
 115         /* The HC driver's private data is stored at the end of
 116          * this structure.
 117          */
 118         unsigned long hcd_priv[0]
 119                         __attribute__ ((aligned (sizeof(unsigned long))));
 120 };
 121
 122 /* 2.4 does this a bit differently ... */
 123 static inline struct usb_bus *hcd_to_bus (struct usb_hcd *hcd)
 124 {
 125         return &hcd->self;
 126 }
 127
 128
 129 // urb.hcpriv is really hardware-specific
 130
 131 struct hcd_timeout {    /* timeouts we allocate */
 132         struct list_head        timeout_list;
 133         struct timer_list       timer;
 134 };
 135
 136 /*-------------------------------------------------------------------------*/
 137
 138 /*
 139  * FIXME usb_operations should vanish or become hc_driver,
 140  * when usb_bus and usb_hcd become the same thing.
 141  */
 142
 143 struct usb_operations {
 144         int (*get_frame_number) (struct usb_device *usb_dev);
 145         int (*submit_urb) (struct urb *urb, int mem_flags);
 146         int (*unlink_urb) (struct urb *urb, int status);
 147
 148         /* allocate dma-consistent buffer for URB_DMA_NOMAPPING */
 149         void *(*buffer_alloc)(struct usb_bus *bus, size_t size,
 150                         int mem_flags,
 151                         dma_addr_t *dma);
 152         void (*buffer_free)(struct usb_bus *bus, size_t size,
 153                         void *addr, dma_addr_t dma);
 154
 155         void (*disable)(struct usb_device *udev,
 156                         struct usb_host_endpoint *ep);
 157
 158         /* global suspend/resume of bus */
 159         int (*hub_suspend)(struct usb_bus *);
 160         int (*hub_resume)(struct usb_bus *);
 161 };
 162
 163 /* each driver provides one of these, and hardware init support */
 164
 165 struct pt_regs;
 166
 167 struct hc_driver {
 168         const char      *description;   /* "ehci-hcd" etc */
 169         const char      *product_desc;  /* product/vendor string */
 170         size_t          hcd_priv_size;  /* size of private data */
 171
 172         /* irq handler */
 173         irqreturn_t     (*irq) (struct usb_hcd *hcd, struct pt_regs *regs);
 174
 175         int     flags;
 176 #define HCD_MEMORY      0x0001          /* HC regs use memory (else I/O) */
 177 #define HCD_USB11       0x0010          /* USB 1.1 */
 178 #define HCD_USB2        0x0020          /* USB 2.0 */
 179
 180         /* called to init HCD and root hub */
 181         int     (*reset) (struct usb_hcd *hcd);
 182         int     (*start) (struct usb_hcd *hcd);
 183
 184         /* NOTE:  these suspend/resume calls relate to the HC as
 185          * a whole, not just the root hub; they're for bus glue.
 186          */
 187         /* called after all devices were suspended */
 188         int     (*suspend) (struct usb_hcd *hcd, pm_message_t message);
 189
 190         /* called before any devices get resumed */
 191         int     (*resume) (struct usb_hcd *hcd);
 192
 193         /* cleanly make HCD stop writing memory and doing I/O */
 194         void    (*stop) (struct usb_hcd *hcd);
 195
 196         /* return current frame number */
 197         int     (*get_frame_number) (struct usb_hcd *hcd);
 198
 199         /* manage i/o requests, device state */
 200         int     (*urb_enqueue) (struct usb_hcd *hcd,
 201                                         struct usb_host_endpoint *ep,
 202                                         struct urb *urb,
 203                                         int mem_flags);
 204         int     (*urb_dequeue) (struct usb_hcd *hcd, struct urb *urb);
 205
 206         /* hw synch, freeing endpoint resources that urb_dequeue can't */
 207         void    (*endpoint_disable)(struct usb_hcd *hcd,
 208                         struct usb_host_endpoint *ep);
 209
 210         /* root hub support */
 211         int             (*hub_status_data) (struct usb_hcd *hcd, char *buf);
 212         int             (*hub_control) (struct usb_hcd *hcd,
 213                                 u16 typeReq, u16 wValue, u16 wIndex,
 214                                 char *buf, u16 wLength);
 215         int             (*hub_suspend)(struct usb_hcd *);
 216         int             (*hub_resume)(struct usb_hcd *);
 217         int             (*start_port_reset)(struct usb_hcd *, unsigned port_num);
 218         void            (*hub_irq_enable)(struct usb_hcd *);
 219                 /* Needed only if port-change IRQs are level-triggered */
 220 };
 221
 222 extern void usb_hcd_giveback_urb (struct usb_hcd *hcd, struct urb *urb, struct pt_regs *regs);
 223
 224 extern struct usb_hcd *usb_create_hcd (const struct hc_driver *driver,
 225                 struct device *dev, char *bus_name);
 226 extern void usb_put_hcd (struct usb_hcd *hcd);
 227 extern int usb_add_hcd(struct usb_hcd *hcd,
 228                 unsigned int irqnum, unsigned long irqflags);
 229 extern void usb_remove_hcd(struct usb_hcd *hcd);
 230
 231 #ifdef CONFIG_PCI
 232 struct pci_dev;
 233 struct pci_device_id;
 234 extern int usb_hcd_pci_probe (struct pci_dev *dev,
 235                                 const struct pci_device_id *id);
 236 extern void usb_hcd_pci_remove (struct pci_dev *dev);
 237
 238 #ifdef CONFIG_PM
 239 extern int usb_hcd_pci_suspend (struct pci_dev *dev, pm_message_t state);
 240 extern int usb_hcd_pci_resume (struct pci_dev *dev);
 241 #endif /* CONFIG_PM */
 242
 243 #endif /* CONFIG_PCI */
 244
 245 /* pci-ish (pdev null is ok) buffer alloc/mapping support */
 246 int hcd_buffer_create (struct usb_hcd *hcd);
 247 void hcd_buffer_destroy (struct usb_hcd *hcd);
 248
 249 void *hcd_buffer_alloc (struct usb_bus *bus, size_t size,
 250         int mem_flags, dma_addr_t *dma);
 251 void hcd_buffer_free (struct usb_bus *bus, size_t size,
 252         void *addr, dma_addr_t dma);
 253
 254 /* generic bus glue, needed for host controllers that don't use PCI */
 255 extern irqreturn_t usb_hcd_irq (int irq, void *__hcd, struct pt_regs *r);
 256
 257 extern void usb_hc_died (struct usb_hcd *hcd);
 258 extern void usb_hcd_poll_rh_status(struct usb_hcd *hcd);
 259
 260 /* -------------------------------------------------------------------------- */
 261
 262 /* Enumeration is only for the hub driver, or HCD virtual root hubs */
 263 extern struct usb_device *usb_alloc_dev(struct usb_device *parent,
 264                                         struct usb_bus *, unsigned port);
 265 extern int usb_new_device(struct usb_device *dev);
 266 extern void usb_disconnect(struct usb_device **);
 267
 268 extern int usb_get_configuration(struct usb_device *dev);
 269 extern void usb_destroy_configuration(struct usb_device *dev);
 270
 271 /*-------------------------------------------------------------------------*/
 272
 273 /*
 274  * HCD Root Hub support
 275  */
 276
 277 #include "hub.h"
 278
 279 /* (shifted) direction/type/recipient from the USB 2.0 spec, table 9.2 */
 280 #define DeviceRequest \
 281         ((USB_DIR_IN|USB_TYPE_STANDARD|USB_RECIP_DEVICE)<<8)
 282 #define DeviceOutRequest \
 283         ((USB_DIR_OUT|USB_TYPE_STANDARD|USB_RECIP_DEVICE)<<8)
 284
 285 #define InterfaceRequest \
 286         ((USB_DIR_IN|USB_TYPE_STANDARD|USB_RECIP_INTERFACE)<<8)
 287
 288 #define EndpointRequest \
 289         ((USB_DIR_IN|USB_TYPE_STANDARD|USB_RECIP_INTERFACE)<<8)
 290 #define EndpointOutRequest \
 291         ((USB_DIR_OUT|USB_TYPE_STANDARD|USB_RECIP_INTERFACE)<<8)
 292
 293 /* class requests from the USB 2.0 hub spec, table 11-15 */
 294 /* GetBusState and SetHubDescriptor are optional, omitted */
 295 #define ClearHubFeature         (0x2000 | USB_REQ_CLEAR_FEATURE)
 296 #define ClearPortFeature        (0x2300 | USB_REQ_CLEAR_FEATURE)
 297 #define GetHubDescriptor        (0xa000 | USB_REQ_GET_DESCRIPTOR)
 298 #define GetHubStatus            (0xa000 | USB_REQ_GET_STATUS)
 299 #define GetPortStatus           (0xa300 | USB_REQ_GET_STATUS)
 300 #define SetHubFeature           (0x2000 | USB_REQ_SET_FEATURE)
 301 #define SetPortFeature          (0x2300 | USB_REQ_SET_FEATURE)
 302
 303
 304 /*-------------------------------------------------------------------------*/
 305
 306 /*
 307  * Generic bandwidth allocation constants/support
 308  */
 309 #define FRAME_TIME_USECS        1000L
 310 #define BitTime(bytecount)  (7 * 8 * bytecount / 6)  /* with integer truncation */
 311                 /* Trying not to use worst-case bit-stuffing
 312                    of (7/6 * 8 * bytecount) = 9.33 * bytecount */
 313                 /* bytecount = data payload byte count */
 314
 315 #define NS_TO_US(ns)    ((ns + 500L) / 1000L)
 316                         /* convert & round nanoseconds to microseconds */
 317
 318 extern void usb_claim_bandwidth (struct usb_device *dev, struct urb *urb,
 319                 int bustime, int isoc);
 320 extern void usb_release_bandwidth (struct usb_device *dev, struct urb *urb,
 321                 int isoc);
 322
 323 /*
 324  * Full/low speed bandwidth allocation constants/support.
 325  */
 326 #define BW_HOST_DELAY   1000L           /* nanoseconds */
 327 #define BW_HUB_LS_SETUP 333L            /* nanoseconds */
 328                         /* 4 full-speed bit times (est.) */
 329
 330 #define FRAME_TIME_BITS         12000L          /* frame = 1 millisecond */
 331 #define FRAME_TIME_MAX_BITS_ALLOC       (90L * FRAME_TIME_BITS / 100L)
 332 #define FRAME_TIME_MAX_USECS_ALLOC      (90L * FRAME_TIME_USECS / 100L)
 333
 334 extern int usb_check_bandwidth (struct usb_device *dev, struct urb *urb);
 335
 336 /*
 337  * Ceiling microseconds (typical) for that many bytes at high speed
 338  * ISO is a bit less, no ACK ... from USB 2.0 spec, 5.11.3 (and needed
 339  * to preallocate bandwidth)
 340  */
 341 #define USB2_HOST_DELAY 5       /* nsec, guess */
 342 #define HS_USECS(bytes) NS_TO_US ( ((55 * 8 * 2083)/1000) \
 343         + ((2083UL * (3167 + BitTime (bytes)))/1000) \
 344         + USB2_HOST_DELAY)
 345 #define HS_USECS_ISO(bytes) NS_TO_US ( ((38 * 8 * 2083)/1000) \
 346         + ((2083UL * (3167 + BitTime (bytes)))/1000) \
 347         + USB2_HOST_DELAY)
 348
 349 extern long usb_calc_bus_time (int speed, int is_input,
 350                         int isoc, int bytecount);
 351
 352 /*-------------------------------------------------------------------------*/
 353
 354 extern struct usb_bus *usb_alloc_bus (struct usb_operations *);
 355
 356 extern void usb_hcd_resume_root_hub (struct usb_hcd *hcd);
 357
 358 extern void usb_set_device_state(struct usb_device *udev,
 359                 enum usb_device_state new_state);
 360
 361 /*-------------------------------------------------------------------------*/
 362
 363 /* exported only within usbcore */
 364
 365 extern struct list_head usb_bus_list;
 366 extern struct semaphore usb_bus_list_lock;
 367 extern wait_queue_head_t usb_kill_urb_queue;
 368
 369 extern struct usb_bus *usb_bus_get (struct usb_bus *bus);
 370 extern void usb_bus_put (struct usb_bus *bus);
 371
 372 extern void usb_enable_root_hub_irq (struct usb_bus *bus);
 373
 374 extern int usb_find_interface_driver (struct usb_device *dev,
 375         struct usb_interface *interface);
 376
 377 #define usb_endpoint_out(ep_dir)        (!((ep_dir) & USB_DIR_IN))
 378
 379 /*
 380  * USB device fs stuff
 381  */
 382
 383 #ifdef CONFIG_USB_DEVICEFS
 384
 385 /*
 386  * these are expected to be called from the USB core/hub thread
 387  * with the kernel lock held
 388  */
 389 extern void usbfs_add_bus(struct usb_bus *bus);
 390 extern void usbfs_remove_bus(struct usb_bus *bus);
 391 extern void usbfs_add_device(struct usb_device *dev);
 392 extern void usbfs_remove_device(struct usb_device *dev);
 393 extern void usbfs_update_special (void);
 394
 395 extern int usbfs_init(void);
 396 extern void usbfs_cleanup(void);
 397
 398 #else /* CONFIG_USB_DEVICEFS */
 399
 400 static inline void usbfs_add_bus(struct usb_bus *bus) {}
 401 static inline void usbfs_remove_bus(struct usb_bus *bus) {}
 402 static inline void usbfs_add_device(struct usb_device *dev) {}
 403 static inline void usbfs_remove_device(struct usb_device *dev) {}
 404 static inline void usbfs_update_special (void) {}
 405
 406 static inline int usbfs_init(void) { return 0; }
 407 static inline void usbfs_cleanup(void) { }
 408
 409 #endif /* CONFIG_USB_DEVICEFS */
 410
 411 /*-------------------------------------------------------------------------*/
 412
 413 #if defined(CONFIG_USB_MON)
 414
 415 struct usb_mon_operations {
 416         void (*urb_submit)(struct usb_bus *bus, struct urb *urb);
 417         void (*urb_submit_error)(struct usb_bus *bus, struct urb *urb, int err);
 418         void (*urb_complete)(struct usb_bus *bus, struct urb *urb);
 419         /* void (*urb_unlink)(struct usb_bus *bus, struct urb *urb); */
 420         void (*bus_add)(struct usb_bus *bus);
 421         void (*bus_remove)(struct usb_bus *bus);
 422 };
 423
 424 extern struct usb_mon_operations *mon_ops;
 425
 426 static inline void usbmon_urb_submit(struct usb_bus *bus, struct urb *urb)
 427 {
 428         if (bus->monitored)
 429                 (*mon_ops->urb_submit)(bus, urb);
 430 }
 431
 432 static inline void usbmon_urb_submit_error(struct usb_bus *bus, struct urb *urb,
 433     int error)
 434 {
 435         if (bus->monitored)
 436                 (*mon_ops->urb_submit_error)(bus, urb, error);
 437 }
 438
 439 static inline void usbmon_urb_complete(struct usb_bus *bus, struct urb *urb)
 440 {
 441         if (bus->monitored)
 442                 (*mon_ops->urb_complete)(bus, urb);
 443 }
 444
 445 static inline void usbmon_notify_bus_add(struct usb_bus *bus)
 446 {
 447         if (mon_ops)
 448                 (*mon_ops->bus_add)(bus);
 449 }
 450
 451 static inline void usbmon_notify_bus_remove(struct usb_bus *bus)
 452 {
 453         if (mon_ops)
 454                 (*mon_ops->bus_remove)(bus);
 455 }
 456
 457 int usb_mon_register(struct usb_mon_operations *ops);
 458 void usb_mon_deregister(void);
 459
 460 #else
 461
 462 static inline void usbmon_urb_submit(struct usb_bus *bus, struct urb *urb) {}
 463 static inline void usbmon_urb_submit_error(struct usb_bus *bus, struct urb *urb,
 464     int error) {}
 465 static inline void usbmon_urb_complete(struct usb_bus *bus, struct urb *urb) {}
 466 static inline void usbmon_notify_bus_add(struct usb_bus *bus) {}
 467 static inline void usbmon_notify_bus_remove(struct usb_bus *bus) {}
 468
 469 #endif /* CONFIG_USB_MON */
 470
 471 /*-------------------------------------------------------------------------*/
 472
 473 /* hub.h ... DeviceRemovable in 2.4.2-ac11, gone in 2.4.10 */
 474 // bleech -- resurfaced in 2.4.11 or 2.4.12
 475 #define bitmap  DeviceRemovable
 476
 477
 478 /*-------------------------------------------------------------------------*/
 479
 480 /* random stuff */
 481
 482 #define RUN_CONTEXT (in_irq () ? "in_irq" \
 483                 : (in_interrupt () ? "in_interrupt" : "can sleep"))
 484
 485
 486 #endif /* __KERNEL__ */
 487