s2io/vxge: Move the Exar drivers

[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / drivers / net / Kconfig

#
# Network device configuration
#

config HAVE_NET_MACB
        bool

menuconfig NETDEVICES
        default y if UML
        depends on NET
        bool "Network device support"
        ---help---
          You can say N here if you don't intend to connect your Linux box to
          any other computer at all.

          You'll have to say Y if your computer contains a network card that
          you want to use under Linux. If you are going to run SLIP or PPP over
          telephone line or null modem cable you need say Y here. Connecting
          two machines with parallel ports using PLIP needs this, as well as
          AX.25/KISS for sending Internet traffic over amateur radio links.

          See also "The Linux Network Administrator's Guide" by Olaf Kirch and
          Terry Dawson. Available at <http://www.tldp.org/guides.html>.

          If unsure, say Y.

# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
if NETDEVICES

config IFB
        tristate "Intermediate Functional Block support"
        depends on NET_CLS_ACT
        ---help---
          This is an intermediate driver that allows sharing of
          resources.
          To compile this driver as a module, choose M here: the module
          will be called ifb.  If you want to use more than one ifb
          device at a time, you need to compile this driver as a module.
          Instead of 'ifb', the devices will then be called 'ifb0',
          'ifb1' etc.
          Look at the iproute2 documentation directory for usage etc

config DUMMY
        tristate "Dummy net driver support"
        ---help---
          This is essentially a bit-bucket device (i.e. traffic you send to
          this device is consigned into oblivion) with a configurable IP
          address. It is most commonly used in order to make your currently
          inactive SLIP address seem like a real address for local programs.
          If you use SLIP or PPP, you might want to say Y here. Since this
          thing often comes in handy, the default is Y. It won't enlarge your
          kernel either. What a deal. Read about it in the Network
          Administrator's Guide, available from
          <http://www.tldp.org/docs.html#guide>.

          To compile this driver as a module, choose M here: the module
          will be called dummy.  If you want to use more than one dummy
          device at a time, you need to compile this driver as a module.
          Instead of 'dummy', the devices will then be called 'dummy0',
          'dummy1' etc.

config BONDING
        tristate "Bonding driver support"
        depends on INET
        depends on IPV6 || IPV6=n
        ---help---
          Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
          Channels together. This is called 'Etherchannel' by Cisco,
          'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.

          The driver supports multiple bonding modes to allow for both high
          performance and high availability operation.

          Refer to <file:Documentation/networking/bonding.txt> for more
          information.

          To compile this driver as a module, choose M here: the module
          will be called bonding.

config MACVLAN
        tristate "MAC-VLAN support (EXPERIMENTAL)"
        depends on EXPERIMENTAL
        ---help---
          This allows one to create virtual interfaces that map packets to
          or from specific MAC addresses to a particular interface.

          Macvlan devices can be added using the "ip" command from the
          iproute2 package starting with the iproute2-2.6.23 release:

          "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"

          To compile this driver as a module, choose M here: the module
          will be called macvlan.

config MACVTAP
        tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
        depends on MACVLAN
        help
          This adds a specialized tap character device driver that is based
          on the MAC-VLAN network interface, called macvtap. A macvtap device
          can be added in the same way as a macvlan device, using 'type
          macvlan', and then be accessed through the tap user space interface.

          To compile this driver as a module, choose M here: the module
          will be called macvtap.

config EQUALIZER
        tristate "EQL (serial line load balancing) support"
        ---help---
          If you have two serial connections to some other computer (this
          usually requires two modems and two telephone lines) and you use
          SLIP (the protocol for sending Internet traffic over telephone
          lines) or PPP (a better SLIP) on them, you can make them behave like
          one double speed connection using this driver.  Naturally, this has
          to be supported at the other end as well, either with a similar EQL
          Linux driver or with a Livingston Portmaster 2e.

          Say Y if you want this and read
          <file:Documentation/networking/eql.txt>.  You may also want to read
          section 6.2 of the NET-3-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the module
          will be called eql.  If unsure, say N.

config TUN
        tristate "Universal TUN/TAP device driver support"
        select CRC32
        ---help---
          TUN/TAP provides packet reception and transmission for user space
          programs.  It can be viewed as a simple Point-to-Point or Ethernet
          device, which instead of receiving packets from a physical media,
          receives them from user space program and instead of sending packets
          via physical media writes them to the user space program.

          When a program opens /dev/net/tun, driver creates and registers
          corresponding net device tunX or tapX.  After a program closed above
          devices, driver will automatically delete tunXX or tapXX device and
          all routes corresponding to it.

          Please read <file:Documentation/networking/tuntap.txt> for more
          information.

          To compile this driver as a module, choose M here: the module
          will be called tun.

          If you don't know what to use this for, you don't need it.

config VETH
        tristate "Virtual ethernet pair device"
        ---help---
          This device is a local ethernet tunnel. Devices are created in pairs.
          When one end receives the packet it appears on its pair and vice
          versa.

config NET_SB1000
        tristate "General Instruments Surfboard 1000"
        depends on PNP
        ---help---
          This is a driver for the General Instrument (also known as
          NextLevel) SURFboard 1000 internal
          cable modem. This is an ISA card which is used by a number of cable
          TV companies to provide cable modem access. It's a one-way
          downstream-only cable modem, meaning that your upstream net link is
          provided by your regular phone modem.

          At present this driver only compiles as a module, so say M here if
          you have this card. The module will be called sb1000. Then read
          <file:Documentation/networking/README.sb1000> for information on how
          to use this module, as it needs special ppp scripts for establishing
          a connection. Further documentation and the necessary scripts can be
          found at:

          <http://www.jacksonville.net/~fventuri/>
          <http://home.adelphia.net/~siglercm/sb1000.html>
          <http://linuxpower.cx/~cable/>

          If you don't have this card, of course say N.

source "drivers/net/arcnet/Kconfig"

config MII
        tristate "Generic Media Independent Interface device support"
        help
          Most ethernet controllers have MII transceiver either as an external
          or internal device.  It is safe to say Y or M here even if your
          ethernet card lacks MII.

source "drivers/net/phy/Kconfig"

#
#       Ethernet
#

source "drivers/net/ethernet/Kconfig"

menuconfig NET_ETHERNET
        bool "Ethernet (10 or 100Mbit)"
        depends on !UML
        ---help---
          Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
          type of Local Area Network (LAN) in universities and companies.

          Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
          coaxial cable, linking computers in a chain), 10BASE-T or twisted
          pair (10 Mbps over twisted pair cable, linking computers to central
          hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
          100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
          100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
          cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
          [the 100BASE varieties are also known as Fast Ethernet], and Gigabit
          Ethernet (1 Gbps over optical fiber or short copper links).

          If your Linux machine will be connected to an Ethernet and you have
          an Ethernet network interface card (NIC) installed in your computer,
          say Y here and read the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>. You will then also have
          to say Y to the driver for your particular NIC.

          Note that the answer to this question won't directly affect the
          kernel: saying N will just cause the configurator to skip all
          the questions about Ethernet network cards. If unsure, say N.

if NET_ETHERNET

config MACB
        tristate "Atmel MACB support"
        depends on HAVE_NET_MACB
        select PHYLIB
        help
          The Atmel MACB ethernet interface is found on many AT32 and AT91
          parts. Say Y to include support for the MACB chip.

          To compile this driver as a module, choose M here: the module
          will be called macb.

source "drivers/net/arm/Kconfig"

config MACE
        tristate "MACE (Power Mac ethernet) support"
        depends on PPC_PMAC && PPC32
        select CRC32
        help
          Power Macintoshes and clones with Ethernet built-in on the
          motherboard will usually use a MACE (Medium Access Control for
          Ethernet) interface. Say Y to include support for the MACE chip.

          To compile this driver as a module, choose M here: the module
          will be called mace.

config MACE_AAUI_PORT
        bool "Use AAUI port instead of TP by default"
        depends on MACE
        help
          Some Apple machines (notably the Apple Network Server) which use the
          MACE ethernet chip have an Apple AUI port (small 15-pin connector),
          instead of an 8-pin RJ45 connector for twisted-pair ethernet.  Say
          Y here if you have such a machine.  If unsure, say N.
          The driver will default to AAUI on ANS anyway, and if you use it as
          a module, you can provide the port_aaui=0|1 to force the driver.

config BMAC
        tristate "BMAC (G3 ethernet) support"
        depends on PPC_PMAC && PPC32
        select CRC32
        help
          Say Y for support of BMAC Ethernet interfaces. These are used on G3
          computers.

          To compile this driver as a module, choose M here: the module
          will be called bmac.

config MAC89x0
        tristate "Macintosh CS89x0 based ethernet cards"
        depends on MAC
        ---help---
          Support for CS89x0 chipset based Ethernet cards.  If you have a
          Nubus or LC-PDS network (Ethernet) card of this type, say Y and
          read the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. This module will
          be called mac89x0.

config MACSONIC
        tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
        depends on MAC
        ---help---
          Support for NatSemi SONIC based Ethernet devices.  This includes
          the onboard Ethernet in many Quadras as well as some LC-PDS,
          a few Nubus and all known Comm Slot Ethernet cards.  If you have
          one of these say Y and read the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. This module will
          be called macsonic.

config MACMACE
        bool "Macintosh (AV) onboard MACE ethernet"
        depends on MAC
        select CRC32
        help
          Support for the onboard AMD 79C940 MACE Ethernet controller used in
          the 660AV and 840AV Macintosh.  If you have one of these Macintoshes
          say Y and read the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

config KORINA
        tristate "Korina (IDT RC32434) Ethernet support"
        depends on NET_ETHERNET && MIKROTIK_RB532
        help
          If you have a Mikrotik RouterBoard 500 or IDT RC32434
          based system say Y. Otherwise say N.

config MIPS_JAZZ_SONIC
        tristate "MIPS JAZZ onboard SONIC Ethernet support"
        depends on MACH_JAZZ
        help
          This is the driver for the onboard card of MIPS Magnum 4000,
          Acer PICA, Olivetti M700-10 and a few other identical OEM systems.

config XTENSA_XT2000_SONIC
        tristate "Xtensa XT2000 onboard SONIC Ethernet support"
        depends on XTENSA_PLATFORM_XT2000
        help
          This is the driver for the onboard card of the Xtensa XT2000 board.

config SGI_IOC3_ETH
        bool "SGI IOC3 Ethernet"
        depends on PCI && SGI_IP27
        select CRC32
        select MII
        help
          If you have a network (Ethernet) card of this type, say Y and read
          the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

config MIPS_SIM_NET
        tristate "MIPS simulator Network device"
        depends on MIPS_SIM
        help
          The MIPSNET device is a simple Ethernet network device which is
          emulated by the MIPS Simulator.
          If you are not using a MIPSsim or are unsure, say N.

config SGI_O2MACE_ETH
        tristate "SGI O2 MACE Fast Ethernet support"
        depends on SGI_IP32=y

config SH_ETH
        tristate "Renesas SuperH Ethernet support"
        depends on SUPERH && \
                (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || \
                 CPU_SUBTYPE_SH7763 || CPU_SUBTYPE_SH7619 || \
                 CPU_SUBTYPE_SH7724 || CPU_SUBTYPE_SH7757)
        select CRC32
        select MII
        select MDIO_BITBANG
        select PHYLIB
        help
          Renesas SuperH Ethernet device driver.
          This driver supporting CPUs are:
                - SH7710, SH7712, SH7763, SH7619, SH7724, and SH7757.

config BFIN_MAC
        tristate "Blackfin on-chip MAC support"
        depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
        select CRC32
        select MII
        select PHYLIB
        select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
        help
          This is the driver for Blackfin on-chip mac device. Say Y if you want it
          compiled into the kernel. This driver is also available as a module
          ( = code which can be inserted in and removed from the running kernel
          whenever you want). The module will be called bfin_mac.

config BFIN_MAC_USE_L1
        bool "Use L1 memory for rx/tx packets"
        depends on BFIN_MAC && (BF527 || BF537)
        default y
        help
          To get maximum network performance, you should use L1 memory as rx/tx buffers.
          Say N here if you want to reserve L1 memory for other uses.

config BFIN_TX_DESC_NUM
        int "Number of transmit buffer packets"
        depends on BFIN_MAC
        range 6 10 if BFIN_MAC_USE_L1
        range 10 100
        default "10"
        help
          Set the number of buffer packets used in driver.

config BFIN_RX_DESC_NUM
        int "Number of receive buffer packets"
        depends on BFIN_MAC
        range 20 100 if BFIN_MAC_USE_L1
        range 20 800
        default "20"
        help
          Set the number of buffer packets used in driver.

config BFIN_MAC_USE_HWSTAMP
        bool "Use IEEE 1588 hwstamp"
        depends on BFIN_MAC && BF518
        default y
        help
          To support the IEEE 1588 Precision Time Protocol (PTP), select y here

config PXA168_ETH
        tristate "Marvell pxa168 ethernet support"
        depends on CPU_PXA168
        select PHYLIB
        help
          This driver supports the pxa168 Ethernet ports.

          To compile this driver as a module, choose M here. The module
          will be called pxa168_eth.

config NET_NETX
        tristate "NetX Ethernet support"
        select MII
        depends on ARCH_NETX
        help
          This is support for the Hilscher netX builtin Ethernet ports

          To compile this driver as a module, choose M here. The module
          will be called netx-eth.

config TI_DAVINCI_EMAC
        tristate "TI DaVinci EMAC Support"
        depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
        select TI_DAVINCI_MDIO
        select TI_DAVINCI_CPDMA
        select PHYLIB
        help
          This driver supports TI's DaVinci Ethernet .

          To compile this driver as a module, choose M here: the module
          will be called davinci_emac_driver.  This is recommended.

config TI_DAVINCI_MDIO
        tristate "TI DaVinci MDIO Support"
        depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
        select PHYLIB
        help
          This driver supports TI's DaVinci MDIO module.

          To compile this driver as a module, choose M here: the module
          will be called davinci_mdio.  This is recommended.

config TI_DAVINCI_CPDMA
        tristate "TI DaVinci CPDMA Support"
        depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
        help
          This driver supports TI's DaVinci CPDMA dma engine.

          To compile this driver as a module, choose M here: the module
          will be called davinci_cpdma.  This is recommended.

config DM9000
        tristate "DM9000 support"
        depends on ARM || BLACKFIN || MIPS
        select CRC32
        select MII
        ---help---
          Support for DM9000 chipset.

          To compile this driver as a module, choose M here.  The module
          will be called dm9000.

config DM9000_DEBUGLEVEL
        int "DM9000 maximum debug level"
        depends on DM9000
        default 4
        help
          The maximum level of debugging code compiled into the DM9000
          driver.

config DM9000_FORCE_SIMPLE_PHY_POLL
        bool "Force simple NSR based PHY polling"
        depends on DM9000
        ---help---
          This configuration forces the DM9000 to use the NSR's LinkStatus
          bit to determine if the link is up or down instead of the more
          costly MII PHY reads. Note, this will not work if the chip is
          operating with an external PHY.

config ENC28J60
        tristate "ENC28J60 support"
        depends on EXPERIMENTAL && SPI && NET_ETHERNET
        select CRC32
        ---help---
          Support for the Microchip EN28J60 ethernet chip.

          To compile this driver as a module, choose M here. The module will be
          called enc28j60.

config ENC28J60_WRITEVERIFY
        bool "Enable write verify"
        depends on ENC28J60
        ---help---
          Enable the verify after the buffer write useful for debugging purpose.
          If unsure, say N.

config ETHOC
        tristate "OpenCores 10/100 Mbps Ethernet MAC support"
        depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
        select MII
        select PHYLIB
        select CRC32
        select BITREVERSE
        help
          Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.

config GRETH
        tristate "Aeroflex Gaisler GRETH Ethernet MAC support"
        depends on SPARC
        select PHYLIB
        select CRC32
        help
          Say Y here if you want to use the Aeroflex Gaisler GRETH Ethernet MAC.

config DNET
        tristate "Dave ethernet support (DNET)"
        depends on NET_ETHERNET && HAS_IOMEM
        select PHYLIB
        help
          The Dave ethernet interface (DNET) is found on Qong Board FPGA.
          Say Y to include support for the DNET chip.

          To compile this driver as a module, choose M here: the module
          will be called dnet.

source "drivers/net/tulip/Kconfig"

config AT1700
        tristate "AT1700/1720 support (EXPERIMENTAL)"
        depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
        select CRC32
        ---help---
          If you have a network (Ethernet) card of this type, say Y and read
          the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. The module
          will be called at1700.

config HP100
        tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
        depends on ISA || EISA || PCI
        help
          If you have a network (Ethernet) card of this type, say Y and read
          the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. The module
          will be called hp100.

config NET_ISA
        bool "Other ISA cards"
        depends on ISA
        ---help---
          If your network (Ethernet) card hasn't been mentioned yet and its
          bus system (that's the way the cards talks to the other components
          of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
          Make sure you know the name of your card. Read the Ethernet-HOWTO,
          available from <http://www.tldp.org/docs.html#howto>.

          If unsure, say Y.

          Note that the answer to this question doesn't directly affect the
          kernel: saying N will just cause the configurator to skip all
          the remaining ISA network card questions. If you say Y, you will be
          asked for your specific card in the following questions.

config EWRK3
        tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
        depends on NET_ISA
        select CRC32
        ---help---
          This driver supports the DE203, DE204 and DE205 network (Ethernet)
          cards. If this is for you, say Y and read
          <file:Documentation/networking/ewrk3.txt> in the kernel source as
          well as the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. The module
          will be called ewrk3.

config ETH16I
        tristate "ICL EtherTeam 16i/32 support"
        depends on NET_ISA
        help
          If you have a network (Ethernet) card of this type, say Y and read
          the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. The module
          will be called eth16i.

config SEEQ8005
        tristate "SEEQ8005 support (EXPERIMENTAL)"
        depends on NET_ISA && EXPERIMENTAL
        help
          This is a driver for the SEEQ 8005 network (Ethernet) card.  If this
          is for you, read the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. The module
          will be called seeq8005.

config IBMLANA
        tristate "IBM LAN Adapter/A support"
        depends on MCA
        ---help---
          This is a Micro Channel Ethernet adapter.  You need to set
          CONFIG_MCA to use this driver.  It is both available as an in-kernel
          driver and as a module.

          To compile this driver as a module, choose M here. The only
          currently supported card is the IBM LAN Adapter/A for Ethernet.  It
          will both support 16K and 32K memory windows, however a 32K window
          gives a better security against packet losses.  Usage of multiple
          boards with this driver should be possible, but has not been tested
          up to now due to lack of hardware.

config IBMVETH
        tristate "IBM LAN Virtual Ethernet support"
        depends on PPC_PSERIES
        ---help---
          This driver supports virtual ethernet adapters on newer IBM iSeries
          and pSeries systems.

          To compile this driver as a module, choose M here. The module will
          be called ibmveth.

source "drivers/net/ibm_newemac/Kconfig"

config NET_PCI
        bool "EISA, VLB, PCI and on board controllers"
        depends on ISA || EISA || PCI
        help
          This is another class of network cards which attach directly to the
          bus. If you have one of those, say Y and read the Ethernet-HOWTO,
          available from <http://www.tldp.org/docs.html#howto>.

          Note that the answer to this question doesn't directly affect the
          kernel: saying N will just cause the configurator to skip all
          the questions about this class of network cards. If you say Y, you
          will be asked for your specific card in the following questions. If
          you are unsure, say Y.

config ADAPTEC_STARFIRE
        tristate "Adaptec Starfire/DuraLAN support"
        depends on NET_PCI && PCI
        select CRC32
        select MII
        help
          Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
          adapter. The DuraLAN chip is used on the 64 bit PCI boards from
          Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
          driver.

          To compile this driver as a module, choose M here: the module
          will be called starfire.  This is recommended.

config KSZ884X_PCI
        tristate "Micrel KSZ8841/2 PCI"
        depends on NET_PCI && PCI
        select MII
        select CRC32
        help
          This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.

          To compile this driver as a module, choose M here. The module
          will be called ksz884x.

config FORCEDETH
        tristate "nForce Ethernet support"
        depends on NET_PCI && PCI
        help
          If you have a network (Ethernet) controller of this type, say Y and
          read the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. The module
          will be called forcedeth.

config CS89x0
        tristate "CS89x0 support"
        depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
                || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440)
        ---help---
          Support for CS89x0 chipset based Ethernet cards. If you have a
          network (Ethernet) card of this type, say Y and read the
          Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto> as well as
          <file:Documentation/networking/cs89x0.txt>.

          To compile this driver as a module, choose M here. The module
          will be called cs89x0.

config CS89x0_NONISA_IRQ
        def_bool y
        depends on CS89x0 != n
        depends on MACH_IXDP2351 || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440

config TC35815
        tristate "TOSHIBA TC35815 Ethernet support"
        depends on NET_PCI && PCI && MIPS
        select PHYLIB

config FEALNX
        tristate "Myson MTD-8xx PCI Ethernet support"
        depends on NET_PCI && PCI
        select CRC32
        select MII
        help
          Say Y here to support the Myson MTD-800 family of PCI-based Ethernet 
          cards. <http://www.myson.com.tw/>

config NATSEMI
        tristate "National Semiconductor DP8381x series PCI Ethernet support"
        depends on NET_PCI && PCI
        select CRC32
        help
          This driver is for the National Semiconductor DP83810 series,
          which is used in cards from PureData, NetGear, Linksys
          and others, including the 83815 chip.
          More specific information and updates are available from
          <http://www.scyld.com/network/natsemi.html>.

config 8139CP
        tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
        depends on NET_PCI && PCI && EXPERIMENTAL
        select CRC32
        select MII
        help
          This is a driver for the Fast Ethernet PCI network cards based on
          the RTL8139C+ chips. If you have one of those, say Y and read
          the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the module
          will be called 8139cp.  This is recommended.

config 8139TOO
        tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
        depends on NET_PCI && PCI
        select CRC32
        select MII
        ---help---
          This is a driver for the Fast Ethernet PCI network cards based on
          the RTL 8129/8130/8139 chips. If you have one of those, say Y and
          read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here: the module
          will be called 8139too.  This is recommended.

config 8139TOO_PIO
        bool "Use PIO instead of MMIO"
        default y
        depends on 8139TOO
        help
          This instructs the driver to use programmed I/O ports (PIO) instead
          of PCI shared memory (MMIO).  This can possibly solve some problems
          in case your mainboard has memory consistency issues.  If unsure,
          say N.

config 8139TOO_TUNE_TWISTER
        bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
        depends on 8139TOO
        help
          This implements a function which might come in handy in case you
          are using low quality on long cabling. It is required for RealTek
          RTL-8139 revision K boards, and totally unused otherwise.  It tries
          to match the transceiver to the cable characteristics. This is
          experimental since hardly documented by the manufacturer.
          If unsure, say Y.

config 8139TOO_8129
        bool "Support for older RTL-8129/8130 boards"
        depends on 8139TOO
        help
          This enables support for the older and uncommon RTL-8129 and
          RTL-8130 chips, which support MII via an external transceiver,
          instead of an internal one.  Disabling this option will save some
          memory by making the code size smaller.  If unsure, say Y.

config 8139_OLD_RX_RESET
        bool "Use older RX-reset method"
        depends on 8139TOO
        help
          The 8139too driver was recently updated to contain a more rapid
          reset sequence, in the face of severe receive errors.  This "new"
          RX-reset method should be adequate for all boards.  But if you
          experience problems, you can enable this option to restore the
          old RX-reset behavior.  If unsure, say N.

config R6040
        tristate "RDC R6040 Fast Ethernet Adapter support"
        depends on NET_PCI && PCI
        select CRC32
        select MII
        select PHYLIB
        help
          This is a driver for the R6040 Fast Ethernet MACs found in the
          the RDC R-321x System-on-chips.

          To compile this driver as a module, choose M here: the module
          will be called r6040. This is recommended.

config SIS900
        tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
        depends on NET_PCI && PCI
        select CRC32
        select MII
        ---help---
          This is a driver for the Fast Ethernet PCI network cards based on
          the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
          SiS 630 and SiS 540 chipsets.

          This driver also supports AMD 79C901 HomePNA so that you can use
          your phone line as a network cable.

          To compile this driver as a module, choose M here: the module
          will be called sis900.  This is recommended.

config SUNDANCE
        tristate "Sundance Alta support"
        depends on NET_PCI && PCI
        select CRC32
        select MII
        help
          This driver is for the Sundance "Alta" chip.
          More specific information and updates are available from
          <http://www.scyld.com/network/sundance.html>.

config SUNDANCE_MMIO
        bool "Use MMIO instead of PIO"
        depends on SUNDANCE
        help
          Enable memory-mapped I/O for interaction with Sundance NIC registers.
          Do NOT enable this by default, PIO (enabled when MMIO is disabled)
          is known to solve bugs on certain chips.

          If unsure, say N.

config TLAN
        tristate "TI ThunderLAN support"
        depends on NET_PCI && (PCI || EISA)
        ---help---
          If you have a PCI Ethernet network card based on the ThunderLAN chip
          which is supported by this driver, say Y and read the
          Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          Devices currently supported by this driver are Compaq Netelligent,
          Compaq NetFlex and Olicom cards.  Please read the file
          <file:Documentation/networking/tlan.txt> for more details.

          To compile this driver as a module, choose M here. The module
          will be called tlan.

          Please email feedback to <torben.mathiasen@compaq.com>.

config KS8842
        tristate "Micrel KSZ8841/42 with generic bus interface"
        depends on HAS_IOMEM && DMA_ENGINE
        help
          This platform driver is for KSZ8841(1-port) / KS8842(2-port)
          ethernet switch chip (managed, VLAN, QoS) from Micrel or
          Timberdale(FPGA).

config KS8851
        tristate "Micrel KS8851 SPI"
        depends on SPI
        select MII
        select CRC32
        help
          SPI driver for Micrel KS8851 SPI attached network chip.

config KS8851_MLL
        tristate "Micrel KS8851 MLL"
        depends on HAS_IOMEM
        select MII
        help
          This platform driver is for Micrel KS8851 Address/data bus
          multiplexed network chip.

config VIA_RHINE
        tristate "VIA Rhine support"
        depends on NET_PCI && PCI
        select CRC32
        select MII
        help
          If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
          Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
          Ethernet functions can also be found integrated on South Bridges
          (e.g. VT8235).

          To compile this driver as a module, choose M here. The module
          will be called via-rhine.

config VIA_RHINE_MMIO
        bool "Use MMIO instead of PIO"
        depends on VIA_RHINE
        help
          This instructs the driver to use PCI shared memory (MMIO) instead of
          programmed I/O ports (PIO). Enabling this gives an improvement in
          processing time in parts of the driver.

          If unsure, say Y.

config SC92031
        tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
        depends on NET_PCI && PCI && EXPERIMENTAL
        select CRC32
        ---help---
          This is a driver for the Fast Ethernet PCI network cards based on
          the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
          have one of these, say Y here.

          To compile this driver as a module, choose M here: the module
          will be called sc92031.  This is recommended.

config CPMAC
        tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
        depends on NET_ETHERNET && EXPERIMENTAL && AR7
        select PHYLIB
        help
          TI AR7 CPMAC Ethernet support

config NET_POCKET
        bool "Pocket and portable adapters"
        depends on PARPORT
        ---help---
          Cute little network (Ethernet) devices which attach to the parallel
          port ("pocket adapters"), commonly used with laptops. If you have
          one of those, say Y and read the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          If you want to plug a network (or some other) card into the PCMCIA
          (or PC-card) slot of your laptop instead (PCMCIA is the standard for
          credit card size extension cards used by all modern laptops), you
          need the pcmcia-cs package (location contained in the file
          <file:Documentation/Changes>) and you can say N here.

          Laptop users should read the Linux Laptop home page at
          <http://www.linux-on-laptops.com/> or
          Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>.

          Note that the answer to this question doesn't directly affect the
          kernel: saying N will just cause the configurator to skip all
          the questions about this class of network devices. If you say Y, you
          will be asked for your specific device in the following questions.

config ATP
        tristate "AT-LAN-TEC/RealTek pocket adapter support"
        depends on NET_POCKET && PARPORT && X86
        select CRC32
        ---help---
          This is a network (Ethernet) device which attaches to your parallel
          port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
          available from <http://www.tldp.org/docs.html#howto>, if you
          want to use this.  If you intend to use this driver, you should have
          said N to the "Parallel printer support", because the two drivers
          don't like each other.

          To compile this driver as a module, choose M here: the module
          will be called atp.

config DE600
        tristate "D-Link DE600 pocket adapter support"
        depends on NET_POCKET && PARPORT
        ---help---
          This is a network (Ethernet) device which attaches to your parallel
          port. Read <file:Documentation/networking/DLINK.txt> as well as the
          Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>, if you want to use
          this. It is possible to have several devices share a single parallel
          port and it is safe to compile the corresponding drivers into the
          kernel.

          To compile this driver as a module, choose M here: the module
          will be called de600.

config DE620
        tristate "D-Link DE620 pocket adapter support"
        depends on NET_POCKET && PARPORT
        ---help---
          This is a network (Ethernet) device which attaches to your parallel
          port. Read <file:Documentation/networking/DLINK.txt> as well as the
          Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>, if you want to use
          this. It is possible to have several devices share a single parallel
          port and it is safe to compile the corresponding drivers into the
          kernel.

          To compile this driver as a module, choose M here: the module
          will be called de620.

config SGISEEQ
        tristate "SGI Seeq ethernet controller support"
        depends on SGI_HAS_SEEQ
        help
          Say Y here if you have an Seeq based Ethernet network card. This is
          used in many Silicon Graphics machines.

config FEC
        bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
        depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
                IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC
        default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM
        select PHYLIB
        help
          Say Y here if you want to use the built-in 10/100 Fast ethernet
          controller on some Motorola ColdFire and Freescale i.MX processors.

config FEC_MPC52xx
        tristate "MPC52xx FEC driver"
        depends on PPC_MPC52xx && PPC_BESTCOMM
        select CRC32
        select PHYLIB
        select PPC_BESTCOMM_FEC
        ---help---
          This option enables support for the MPC5200's on-chip
          Fast Ethernet Controller
          If compiled as module, it will be called fec_mpc52xx.

config FEC_MPC52xx_MDIO
        bool "MPC52xx FEC MDIO bus driver"
        depends on FEC_MPC52xx
        default y
        ---help---
          The MPC5200's FEC can connect to the Ethernet either with
          an external MII PHY chip or 10 Mbps 7-wire interface
          (Motorola? industry standard).
          If your board uses an external PHY connected to FEC, enable this.
          If not sure, enable.
          If compiled as module, it will be called fec_mpc52xx_phy.

config ATL2
        tristate "Atheros L2 Fast Ethernet support"
        depends on PCI
        select CRC32
        select MII
        help
          This driver supports the Atheros L2 fast ethernet adapter.

          To compile this driver as a module, choose M here.  The module
          will be called atl2.

config XILINX_EMACLITE
        tristate "Xilinx 10/100 Ethernet Lite support"
        depends on PPC32 || MICROBLAZE
        select PHYLIB
        help
          This driver supports the 10/100 Ethernet Lite from Xilinx.

config FTMAC100
        tristate "Faraday FTMAC100 10/100 Ethernet support"
        depends on ARM
        select MII
        help
          This driver supports the FTMAC100 10/100 Ethernet controller
          from Faraday. It is used on Faraday A320, Andes AG101 and some
          other ARM/NDS32 SoC's.

config LANTIQ_ETOP
        tristate "Lantiq SoC ETOP driver"
        depends on SOC_TYPE_XWAY
        help
          Support for the MII0 inside the Lantiq SoC


source "drivers/net/fs_enet/Kconfig"

source "drivers/net/octeon/Kconfig"

endif # NET_ETHERNET

#
#       Gigabit Ethernet
#

menuconfig NETDEV_1000
        bool "Ethernet (1000 Mbit)"
        depends on !UML
        default y
        ---help---
          Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
          type of Local Area Network (LAN) in universities and companies.

          Say Y here to get to see options for Gigabit Ethernet drivers.
          This option alone does not add any kernel code.
          Note that drivers supporting both 100 and 1000 MBit may be listed
          under "Ethernet (10 or 100MBit)" instead.

          If you say N, all options in this submenu will be skipped and disabled.

if NETDEV_1000

config DL2K
        tristate "DL2000/TC902x-based Gigabit Ethernet support"
        depends on PCI
        select CRC32
        help
          This driver supports DL2000/TC902x-based Gigabit ethernet cards,
          which includes
          D-Link DGE-550T Gigabit Ethernet Adapter.
          D-Link DL2000-based Gigabit Ethernet Adapter.
          Sundance/Tamarack TC902x Gigabit Ethernet Adapter.

          To compile this driver as a module, choose M here: the
          module will be called dl2k.

config IP1000
        tristate "IP1000 Gigabit Ethernet support"
        depends on PCI && EXPERIMENTAL
        select MII
        ---help---
          This driver supports IP1000 gigabit Ethernet cards.

          To compile this driver as a module, choose M here: the module
          will be called ipg.  This is recommended.

source "drivers/net/ixp2000/Kconfig"

config NS83820
        tristate "National Semiconductor DP83820 support"
        depends on PCI
        help
          This is a driver for the National Semiconductor DP83820 series
          of gigabit ethernet MACs.  Cards using this chipset include
          the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX,
          SOHO-GA2000T, SOHO-GA2500T.  The driver supports the use of
          zero copy.

config HAMACHI
        tristate "Packet Engines Hamachi GNIC-II support"
        depends on PCI
        select MII
        help
          If you have a Gigabit Ethernet card of this type, say Y and read
          the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>.

          To compile this driver as a module, choose M here. The module will be
          called hamachi.

config YELLOWFIN
        tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
        depends on PCI && EXPERIMENTAL
        select CRC32
        ---help---
          Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
          adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
          used by the Beowulf Linux cluster project.  See
          <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
          information about this driver in particular and Beowulf in general.

          To compile this driver as a module, choose M here: the module
          will be called yellowfin.  This is recommended.

config R8169
        tristate "Realtek 8169 gigabit ethernet support"
        depends on PCI
        select FW_LOADER
        select CRC32
        select MII
        ---help---
          Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.

          To compile this driver as a module, choose M here: the module
          will be called r8169.  This is recommended.

config SIS190
        tristate "SiS190/SiS191 gigabit ethernet support"
        depends on PCI
        select CRC32
        select MII
        ---help---
          Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
          a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
          appear in lan on motherboard designs which are based on SiS 965
          and SiS 966 south bridge.

          To compile this driver as a module, choose M here: the module
          will be called sis190.  This is recommended.

config SKGE
        tristate "Marvell Yukon Gigabit Ethernet support"
        depends on PCI
        select CRC32
        ---help---
          This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
          and related Gigabit Ethernet adapters. It is a new smaller driver
          with better performance and more complete ethtool support.

          It does not support the link failover and network management 
          features that "portable" vendor supplied sk98lin driver does.

          This driver supports adapters based on the original Yukon chipset:
          Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
          Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.

          It does not support the newer Yukon2 chipset: a separate driver,
          sky2, is provided for these adapters.

          To compile this driver as a module, choose M here: the module
          will be called skge.  This is recommended.

config SKGE_DEBUG
        bool "Debugging interface"
        depends on SKGE && DEBUG_FS
        help
          This option adds the ability to dump driver state for debugging.
          The file /sys/kernel/debug/skge/ethX displays the state of the internal
          transmit and receive rings.

          If unsure, say N.

config SKGE_GENESIS
       bool "Support for older SysKonnect Genesis boards"
       depends on SKGE
       help
         This enables support for the older and uncommon SysKonnect Genesis
         chips, which support MII via an external transceiver, instead of
         an internal one. Disabling this option will save some memory
         by making code smaller. If unsure say Y.

config SKY2
        tristate "Marvell Yukon 2 support"
        depends on PCI
        select CRC32
        ---help---
          This driver supports Gigabit Ethernet adapters based on the
          Marvell Yukon 2 chipset:
          Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
          88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21

          There is companion driver for the older Marvell Yukon and
          SysKonnect Genesis based adapters: skge.

          To compile this driver as a module, choose M here: the module
          will be called sky2.  This is recommended.

config SKY2_DEBUG
        bool "Debugging interface"
        depends on SKY2 && DEBUG_FS
        help
          This option adds the ability to dump driver state for debugging.
          The file /sys/kernel/debug/sky2/ethX displays the state of the internal
          transmit and receive rings.

          If unsure, say N.

config VIA_VELOCITY
        tristate "VIA Velocity support"
        depends on PCI
        select CRC32
        select CRC_CCITT
        select MII
        help
          If you have a VIA "Velocity" based network card say Y here.

          To compile this driver as a module, choose M here. The module
          will be called via-velocity.

config SPIDER_NET
        tristate "Spider Gigabit Ethernet driver"
        depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
        select FW_LOADER
        help
          This driver supports the Gigabit Ethernet chips present on the
          Cell Processor-Based Blades from IBM.

config TSI108_ETH
        tristate "Tundra TSI108 gigabit Ethernet support"
        depends on TSI108_BRIDGE
        help
          This driver supports Tundra TSI108 gigabit Ethernet ports.
          To compile this driver as a module, choose M here: the module
          will be called tsi108_eth.

config GELIC_NET
        tristate "PS3 Gigabit Ethernet driver"
        depends on PPC_PS3
        select PS3_SYS_MANAGER
        help
          This driver supports the network device on the PS3 game
          console.  This driver has built-in support for Ethernet.

          To compile this driver as a module, choose M here: the
          module will be called ps3_gelic.

config GELIC_WIRELESS
        bool "PS3 Wireless support"
        depends on WLAN
        depends on GELIC_NET
        select WIRELESS_EXT
        help
          This option adds the support for the wireless feature of PS3.
          If you have the wireless-less model of PS3 or have no plan to
          use wireless feature, disabling this option saves memory.  As
          the driver automatically distinguishes the models, you can
          safely enable this option even if you have a wireless-less model.

config FSL_PQ_MDIO
        tristate "Freescale PQ MDIO"
        depends on FSL_SOC
        select PHYLIB
        help
          This driver supports the MDIO bus used by the gianfar and UCC drivers.

config GIANFAR
        tristate "Gianfar Ethernet"
        depends on FSL_SOC
        select FSL_PQ_MDIO
        select PHYLIB
        select CRC32
        help
          This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
          and MPC86xx family of chips, and the FEC on the 8540.

config UCC_GETH
        tristate "Freescale QE Gigabit Ethernet"
        depends on QUICC_ENGINE
        select FSL_PQ_MDIO
        select PHYLIB
        help
          This driver supports the Gigabit Ethernet mode of the QUICC Engine,
          which is available on some Freescale SOCs.

config UGETH_TX_ON_DEMAND
        bool "Transmit on Demand support"
        depends on UCC_GETH

config MV643XX_ETH
        tristate "Marvell Discovery (643XX) and Orion ethernet support"
        depends on (MV64X60 || PPC32 || PLAT_ORION) && INET
        select INET_LRO
        select PHYLIB
        help
          This driver supports the gigabit ethernet MACs in the
          Marvell Discovery PPC/MIPS chipset family (MV643XX) and
          in the Marvell Orion ARM SoC family.

          Some boards that use the Discovery chipset are the Momenco
          Ocelot C and Jaguar ATX and Pegasos II.

config XILINX_LL_TEMAC
        tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
        depends on PPC || MICROBLAZE
        select PHYLIB
        help
          This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
          core used in Xilinx Spartan and Virtex FPGAs

config ATL1
        tristate "Atheros/Attansic L1 Gigabit Ethernet support"
        depends on PCI
        select CRC32
        select MII
        help
          This driver supports the Atheros/Attansic L1 gigabit ethernet
          adapter.

          To compile this driver as a module, choose M here.  The module
          will be called atl1.

config ATL1E
        tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)"
        depends on PCI && EXPERIMENTAL
        select CRC32
        select MII
        help
          This driver supports the Atheros L1E gigabit ethernet adapter.

          To compile this driver as a module, choose M here.  The module
          will be called atl1e.

config ATL1C
        tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)"
        depends on PCI && EXPERIMENTAL
        select CRC32
        select MII
        help
          This driver supports the Atheros L1C gigabit ethernet adapter.

          To compile this driver as a module, choose M here.  The module
          will be called atl1c.

config JME
        tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
        depends on PCI
        select CRC32
        select MII
        ---help---
          This driver supports the PCI-Express gigabit ethernet adapters
          based on JMicron JMC250 chipset.

          To compile this driver as a module, choose M here. The module
          will be called jme.

config S6GMAC
        tristate "S6105 GMAC ethernet support"
        depends on XTENSA_VARIANT_S6000
        select PHYLIB
        help
          This driver supports the on chip ethernet device on the
          S6105 xtensa processor.

          To compile this driver as a module, choose M here. The module
          will be called s6gmac.

source "drivers/net/stmmac/Kconfig"

config PCH_GBE
        tristate "Intel EG20T PCH / OKI SEMICONDUCTOR ML7223 IOH GbE"
        depends on PCI
        select MII
        ---help---
          This is a gigabit ethernet driver for EG20T PCH.
          EG20T PCH is the platform controller hub that is used in Intel's
          general embedded platform.
          EG20T PCH has Gigabit Ethernet interface.
          Using this interface, it is able to access system devices connected
          to Gigabit Ethernet.
          This driver enables Gigabit Ethernet function.

          This driver also can be used for OKI SEMICONDUCTOR IOH(Input/
          Output Hub), ML7223.
          ML7223 IOH is for MP(Media Phone) use.
          ML7223 is companion chip for Intel Atom E6xx series.
          ML7223 is completely compatible for Intel EG20T PCH.

config FTGMAC100
        tristate "Faraday FTGMAC100 Gigabit Ethernet support"
        depends on ARM
        select PHYLIB
        help
          This driver supports the FTGMAC100 Gigabit Ethernet controller
          from Faraday. It is used on Faraday A369, Andes AG102 and some
          other ARM/NDS32 SoC's.

endif # NETDEV_1000

#
#       10 Gigabit Ethernet
#

menuconfig NETDEV_10000
        bool "Ethernet (10000 Mbit)"
        depends on !UML
        default y
        ---help---
          Say Y here to get to see options for 10 Gigabit Ethernet drivers.
          This option alone does not add any kernel code.

          If you say N, all options in this submenu will be skipped and disabled.

if NETDEV_10000

config MDIO
        tristate

config EHEA
        tristate "eHEA Ethernet support"
        depends on IBMEBUS && INET && SPARSEMEM
        select INET_LRO
        ---help---
          This driver supports the IBM pSeries eHEA ethernet adapter.

          To compile the driver as a module, choose M here. The module
          will be called ehea.

config ENIC
        tristate "Cisco VIC Ethernet NIC Support"
        depends on PCI && INET
        help
          This enables the support for the Cisco VIC Ethernet card.

config PASEMI_MAC
        tristate "PA Semi 1/10Gbit MAC"
        depends on PPC_PASEMI && PCI && INET
        select PHYLIB
        select INET_LRO
        help
          This driver supports the on-chip 1/10Gbit Ethernet controller on
          PA Semi's PWRficient line of chips.

config TEHUTI
        tristate "Tehuti Networks 10G Ethernet"
        depends on PCI
        help
          Tehuti Networks 10G Ethernet NIC

endif # NETDEV_10000

source "drivers/net/tokenring/Kconfig"

source "drivers/net/wireless/Kconfig"

source "drivers/net/wimax/Kconfig"

source "drivers/net/usb/Kconfig"

source "drivers/net/pcmcia/Kconfig"

source "drivers/net/wan/Kconfig"

source "drivers/atm/Kconfig"

source "drivers/ieee802154/Kconfig"

source "drivers/s390/net/Kconfig"

source "drivers/net/caif/Kconfig"

config TILE_NET
        tristate "Tilera GBE/XGBE network driver support"
        depends on TILE
        default y
        select CRC32
        help
          This is a standard Linux network device driver for the
          on-chip Tilera Gigabit Ethernet and XAUI interfaces.

          To compile this driver as a module, choose M here: the module
          will be called tile_net.

config XEN_NETDEV_FRONTEND
        tristate "Xen network device frontend driver"
        depends on XEN
        select XEN_XENBUS_FRONTEND
        default y
        help
          This driver provides support for Xen paravirtual network
          devices exported by a Xen network driver domain (often
          domain 0).

          The corresponding Linux backend driver is enabled by the
          CONFIG_XEN_NETDEV_BACKEND option.

          If you are compiling a kernel for use as Xen guest, you
          should say Y here. To compile this driver as a module, chose
          M here: the module will be called xen-netfront.

config XEN_NETDEV_BACKEND
        tristate "Xen backend network device"
        depends on XEN_BACKEND
        help
          This driver allows the kernel to act as a Xen network driver
          domain which exports paravirtual network devices to other
          Xen domains. These devices can be accessed by any operating
          system that implements a compatible front end.

          The corresponding Linux frontend driver is enabled by the
          CONFIG_XEN_NETDEV_FRONTEND configuration option.

          The backend driver presents a standard network device
          endpoint for each paravirtual network device to the driver
          domain network stack. These can then be bridged or routed
          etc in order to provide full network connectivity.

          If you are compiling a kernel to run in a Xen network driver
          domain (often this is domain 0) you should say Y here. To
          compile this driver as a module, chose M here: the module
          will be called xen-netback.

config ISERIES_VETH
        tristate "iSeries Virtual Ethernet driver support"
        depends on PPC_ISERIES

config RIONET
        tristate "RapidIO Ethernet over messaging driver support"
        depends on RAPIDIO

config RIONET_TX_SIZE
        int "Number of outbound queue entries"
        depends on RIONET
        default "128"

config RIONET_RX_SIZE
        int "Number of inbound queue entries"
        depends on RIONET
        default "128"

config FDDI
        tristate "FDDI driver support"
        depends on (PCI || EISA || TC)
        help
          Fiber Distributed Data Interface is a high speed local area network
          design; essentially a replacement for high speed Ethernet. FDDI can
          run over copper or fiber. If you are connected to such a network and
          want a driver for the FDDI card in your computer, say Y here (and
          then also Y to the driver for your FDDI card, below). Most people
          will say N.

config DEFXX
        tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
        depends on FDDI && (PCI || EISA || TC)
        ---help---
          This is support for the DIGITAL series of TURBOchannel (DEFTA),
          EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
          to a local FDDI network.

          To compile this driver as a module, choose M here: the module
          will be called defxx.  If unsure, say N.

config DEFXX_MMIO
        bool
        prompt "Use MMIO instead of PIO" if PCI || EISA
        depends on DEFXX
        default n if PCI || EISA
        default y
        ---help---
          This instructs the driver to use EISA or PCI memory-mapped I/O
          (MMIO) as appropriate instead of programmed I/O ports (PIO).
          Enabling this gives an improvement in processing time in parts
          of the driver, but it may cause problems with EISA (DEFEA)
          adapters.  TURBOchannel does not have the concept of I/O ports,
          so MMIO is always used for these (DEFTA) adapters.

          If unsure, say N.

config SKFP
        tristate "SysKonnect FDDI PCI support"
        depends on FDDI && PCI
        select BITREVERSE
        ---help---
          Say Y here if you have a SysKonnect FDDI PCI adapter.
          The following adapters are supported by this driver:
          - SK-5521 (SK-NET FDDI-UP)
          - SK-5522 (SK-NET FDDI-UP DAS)
          - SK-5541 (SK-NET FDDI-FP)
          - SK-5543 (SK-NET FDDI-LP)
          - SK-5544 (SK-NET FDDI-LP DAS)
          - SK-5821 (SK-NET FDDI-UP64)
          - SK-5822 (SK-NET FDDI-UP64 DAS)
          - SK-5841 (SK-NET FDDI-FP64)
          - SK-5843 (SK-NET FDDI-LP64)
          - SK-5844 (SK-NET FDDI-LP64 DAS)
          - Netelligent 100 FDDI DAS Fibre SC
          - Netelligent 100 FDDI SAS Fibre SC
          - Netelligent 100 FDDI DAS UTP
          - Netelligent 100 FDDI SAS UTP
          - Netelligent 100 FDDI SAS Fibre MIC

          Read <file:Documentation/networking/skfp.txt> for information about
          the driver.

          Questions concerning this driver can be addressed to:
          <linux@syskonnect.de>

          To compile this driver as a module, choose M here: the module
          will be called skfp.  This is recommended.

config HIPPI
        bool "HIPPI driver support (EXPERIMENTAL)"
        depends on EXPERIMENTAL && INET && PCI
        help
          HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
          1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
          can run over copper (25m) or fiber (300m on multi-mode or 10km on
          single-mode). HIPPI networks are commonly used for clusters and to
          connect to super computers. If you are connected to a HIPPI network
          and have a HIPPI network card in your computer that you want to use
          under Linux, say Y here (you must also remember to enable the driver
          for your HIPPI card below). Most people will say N here.

config ROADRUNNER
        tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
        depends on HIPPI && PCI
        help
          Say Y here if this is your PCI HIPPI network card.

          To compile this driver as a module, choose M here: the module
          will be called rrunner.  If unsure, say N.

config ROADRUNNER_LARGE_RINGS
        bool "Use large TX/RX rings (EXPERIMENTAL)"
        depends on ROADRUNNER
        help
          If you say Y here, the RoadRunner driver will preallocate up to 2 MB
          of additional memory to allow for fastest operation, both for
          transmitting and receiving. This memory cannot be used by any other
          kernel code or by user space programs. Say Y here only if you have
          the memory.

config PLIP
        tristate "PLIP (parallel port) support"
        depends on PARPORT
        ---help---
          PLIP (Parallel Line Internet Protocol) is used to create a
          reasonably fast mini network consisting of two (or, rarely, more)
          local machines.  A PLIP link from a Linux box is a popular means to
          install a Linux distribution on a machine which doesn't have a
          CD-ROM drive (a minimal system has to be transferred with floppies
          first). The kernels on both machines need to have this PLIP option
          enabled for this to work.

          The PLIP driver has two modes, mode 0 and mode 1.  The parallel
          ports (the connectors at the computers with 25 holes) are connected
          with "null printer" or "Turbo Laplink" cables which can transmit 4
          bits at a time (mode 0) or with special PLIP cables, to be used on
          bidirectional parallel ports only, which can transmit 8 bits at a
          time (mode 1); you can find the wiring of these cables in
          <file:Documentation/networking/PLIP.txt>.  The cables can be up to
          15m long.  Mode 0 works also if one of the machines runs DOS/Windows
          and has some PLIP software installed, e.g. the Crynwr PLIP packet
          driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>)
          and winsock or NCSA's telnet.

          If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well
          as the NET-3-HOWTO, both available from
          <http://www.tldp.org/docs.html#howto>.  Note that the PLIP
          protocol has been changed and this PLIP driver won't work together
          with the PLIP support in Linux versions 1.0.x.  This option enlarges
          your kernel by about 8 KB.

          To compile this driver as a module, choose M here. The module
          will be called plip. If unsure, say Y or M, in case you buy
          a laptop later.

config PPP
        tristate "PPP (point-to-point protocol) support"
        select SLHC
        ---help---
          PPP (Point to Point Protocol) is a newer and better SLIP.  It serves
          the same purpose: sending Internet traffic over telephone (and other
          serial) lines.  Ask your access provider if they support it, because
          otherwise you can't use it; most Internet access providers these
          days support PPP rather than SLIP.

          To use PPP, you need an additional program called pppd as described
          in the PPP-HOWTO, available at
          <http://www.tldp.org/docs.html#howto>.  Make sure that you have
          the version of pppd recommended in <file:Documentation/Changes>.
          The PPP option enlarges your kernel by about 16 KB.

          There are actually two versions of PPP: the traditional PPP for
          asynchronous lines, such as regular analog phone lines, and
          synchronous PPP which can be used over digital ISDN lines for
          example.  If you want to use PPP over phone lines or other
          asynchronous serial lines, you need to say Y (or M) here and also to
          the next option, "PPP support for async serial ports".  For PPP over
          synchronous lines, you should say Y (or M) here and to "Support
          synchronous PPP", below.

          If you said Y to "Version information on all symbols" above, then
          you cannot compile the PPP driver into the kernel; you can then only
          compile it as a module. To compile this driver as a module, choose M
          here. The module will be called ppp_generic.

config PPP_MULTILINK
        bool "PPP multilink support (EXPERIMENTAL)"
        depends on PPP && EXPERIMENTAL
        help
          PPP multilink is a protocol (defined in RFC 1990) which allows you
          to combine several (logical or physical) lines into one logical PPP
          connection, so that you can utilize your full bandwidth.

          This has to be supported at the other end as well and you need a
          version of the pppd daemon which understands the multilink protocol.

          If unsure, say N.

config PPP_FILTER
        bool "PPP filtering"
        depends on PPP
        help
          Say Y here if you want to be able to filter the packets passing over
          PPP interfaces.  This allows you to control which packets count as
          activity (i.e. which packets will reset the idle timer or bring up
          a demand-dialed link) and which packets are to be dropped entirely.
          You need to say Y here if you wish to use the pass-filter and
          active-filter options to pppd.

          If unsure, say N.

config PPP_ASYNC
        tristate "PPP support for async serial ports"
        depends on PPP
        select CRC_CCITT
        ---help---
          Say Y (or M) here if you want to be able to use PPP over standard
          asynchronous serial ports, such as COM1 or COM2 on a PC.  If you use
          a modem (not a synchronous or ISDN modem) to contact your ISP, you
          need this option.

          To compile this driver as a module, choose M here.

          If unsure, say Y.

config PPP_SYNC_TTY
        tristate "PPP support for sync tty ports"
        depends on PPP
        help
          Say Y (or M) here if you want to be able to use PPP over synchronous
          (HDLC) tty devices, such as the SyncLink adapter. These devices
          are often used for high-speed leased lines like T1/E1.

          To compile this driver as a module, choose M here.

config PPP_DEFLATE
        tristate "PPP Deflate compression"
        depends on PPP
        select ZLIB_INFLATE
        select ZLIB_DEFLATE
        ---help---
          Support for the Deflate compression method for PPP, which uses the
          Deflate algorithm (the same algorithm that gzip uses) to compress
          each PPP packet before it is sent over the wire.  The machine at the
          other end of the PPP link (usually your ISP) has to support the
          Deflate compression method as well for this to be useful.  Even if
          they don't support it, it is safe to say Y here.

          To compile this driver as a module, choose M here.

config PPP_BSDCOMP
        tristate "PPP BSD-Compress compression"
        depends on PPP
        ---help---
          Support for the BSD-Compress compression method for PPP, which uses
          the LZW compression method to compress each PPP packet before it is
          sent over the wire. The machine at the other end of the PPP link
          (usually your ISP) has to support the BSD-Compress compression
          method as well for this to be useful. Even if they don't support it,
          it is safe to say Y here.

          The PPP Deflate compression method ("PPP Deflate compression",
          above) is preferable to BSD-Compress, because it compresses better
          and is patent-free.

          Note that the BSD compression code will always be compiled as a
          module; it is called bsd_comp and will show up in the directory
          modules once you have said "make modules". If unsure, say N.

config PPP_MPPE
        tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
        depends on PPP && EXPERIMENTAL
        select CRYPTO
        select CRYPTO_SHA1
        select CRYPTO_ARC4
        select CRYPTO_ECB
        ---help---
          Support for the MPPE Encryption protocol, as employed by the
          Microsoft Point-to-Point Tunneling Protocol.

          See http://pptpclient.sourceforge.net/ for information on
          configuring PPTP clients and servers to utilize this method.

config PPPOE
        tristate "PPP over Ethernet (EXPERIMENTAL)"
        depends on EXPERIMENTAL && PPP
        help
          Support for PPP over Ethernet.

          This driver requires the latest version of pppd from the CVS
          repository at cvs.samba.org.  Alternatively, see the 
          RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
          which contains instruction on how to use this driver (under 
          the heading "Kernel mode PPPoE").

config PPTP
        tristate "PPP over IPv4 (PPTP) (EXPERIMENTAL)"
        depends on EXPERIMENTAL && PPP && NET_IPGRE_DEMUX
        help
          Support for PPP over IPv4.(Point-to-Point Tunneling Protocol)

          This driver requires pppd plugin to work in client mode or
          modified pptpd (poptop) to work in server mode.
          See http://accel-pptp.sourceforge.net/ for information how to
          utilize this module.

config PPPOATM
        tristate "PPP over ATM"
        depends on ATM && PPP
        help
          Support PPP (Point to Point Protocol) encapsulated in ATM frames.
          This implementation does not yet comply with section 8 of RFC2364,
          which can lead to bad results if the ATM peer loses state and
          changes its encapsulation unilaterally.

config PPPOL2TP
        tristate "PPP over L2TP (EXPERIMENTAL)"
        depends on EXPERIMENTAL && L2TP && PPP
        help
          Support for PPP-over-L2TP socket family. L2TP is a protocol
          used by ISPs and enterprises to tunnel PPP traffic over UDP
          tunnels. L2TP is replacing PPTP for VPN uses.

config SLIP
        tristate "SLIP (serial line) support"
        ---help---
          Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
          connect to your Internet service provider or to connect to some
          other local Unix box or if you want to configure your Linux box as a
          Slip/CSlip server for other people to dial in. SLIP (Serial Line
          Internet Protocol) is a protocol used to send Internet traffic over
          serial connections such as telephone lines or null modem cables;
          nowadays, the protocol PPP is more commonly used for this same
          purpose.

          Normally, your access provider has to support SLIP in order for you
          to be able to use it, but there is now a SLIP emulator called SLiRP
          around (available from
          <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
          allows you to use SLIP over a regular dial up shell connection. If
          you plan to use SLiRP, make sure to say Y to CSLIP, below. The
          NET-3-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>, explains how to
          configure SLIP. Note that you don't need this option if you just
          want to run term (term is a program which gives you almost full
          Internet connectivity if you have a regular dial up shell account on
          some Internet connected Unix computer. Read
          <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
          support will enlarge your kernel by about 4 KB. If unsure, say N.

          To compile this driver as a module, choose M here. The module
          will be called slip.

config SLIP_COMPRESSED
        bool "CSLIP compressed headers"
        depends on SLIP
        select SLHC
        ---help---
          This protocol is faster than SLIP because it uses compression on the
          TCP/IP headers (not on the data itself), but it has to be supported
          on both ends. Ask your access provider if you are not sure and
          answer Y, just in case. You will still be able to use plain SLIP. If
          you plan to use SLiRP, the SLIP emulator (available from
          <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
          allows you to use SLIP over a regular dial up shell connection, you
          definitely want to say Y here. The NET-3-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>, explains how to configure
          CSLIP. This won't enlarge your kernel.

config SLHC
        tristate
        help
          This option enables Van Jacobsen serial line header compression
          routines.

config SLIP_SMART
        bool "Keepalive and linefill"
        depends on SLIP
        help
          Adds additional capabilities to the SLIP driver to support the
          RELCOM line fill and keepalive monitoring. Ideal on poor quality
          analogue lines.

config SLIP_MODE_SLIP6
        bool "Six bit SLIP encapsulation"
        depends on SLIP
        help
          Just occasionally you may need to run IP over hostile serial
          networks that don't pass all control characters or are only seven
          bit. Saying Y here adds an extra mode you can use with SLIP:
          "slip6". In this mode, SLIP will only send normal ASCII symbols over
          the serial device. Naturally, this has to be supported at the other
          end of the link as well. It's good enough, for example, to run IP
          over the async ports of a Camtec JNT Pad. If unsure, say N.

config NET_FC
        bool "Fibre Channel driver support"
        depends on SCSI && PCI
        help
          Fibre Channel is a high speed serial protocol mainly used to connect
          large storage devices to the computer; it is compatible with and
          intended to replace SCSI.

          If you intend to use Fibre Channel, you need to have a Fibre channel
          adaptor card in your computer; say Y here and to the driver for your
          adaptor below. You also should have said Y to "SCSI support" and
          "SCSI generic support".

config NETCONSOLE
        tristate "Network console logging support"
        ---help---
        If you want to log kernel messages over the network, enable this.
        See <file:Documentation/networking/netconsole.txt> for details.

config NETCONSOLE_DYNAMIC
        bool "Dynamic reconfiguration of logging targets"
        depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
                        !(NETCONSOLE=y && CONFIGFS_FS=m)
        help
          This option enables the ability to dynamically reconfigure target
          parameters (interface, IP addresses, port numbers, MAC addresses)
          at runtime through a userspace interface exported using configfs.
          See <file:Documentation/networking/netconsole.txt> for details.

config NETPOLL
        def_bool NETCONSOLE

config NETPOLL_TRAP
        bool "Netpoll traffic trapping"
        default n
        depends on NETPOLL

config NET_POLL_CONTROLLER
        def_bool NETPOLL

config VIRTIO_NET
        tristate "Virtio network driver (EXPERIMENTAL)"
        depends on EXPERIMENTAL && VIRTIO
        ---help---
          This is the virtual network driver for virtio.  It can be used with
          lguest or QEMU based VMMs (like KVM or Xen).  Say Y or M.

config VMXNET3
        tristate "VMware VMXNET3 ethernet driver"
        depends on PCI && INET
        help
          This driver supports VMware's vmxnet3 virtual ethernet NIC.
          To compile this driver as a module, choose M here: the
          module will be called vmxnet3.

endif # NETDEVICES