drivers/tty/serial/apbuart.c

   1 /*
   2  *  Driver for GRLIB serial ports (APBUART)
   3  *
   4  *  Based on linux/drivers/serial/amba.c
   5  *
   6  *  Copyright (C) 2000 Deep Blue Solutions Ltd.
   7  *  Copyright (C) 2003 Konrad Eisele <eiselekd@web.de>
   8  *  Copyright (C) 2006 Daniel Hellstrom <daniel@gaisler.com>, Aeroflex Gaisler AB
   9  *  Copyright (C) 2008 Gilead Kutnick <kutnickg@zin-tech.com>
  10  *  Copyright (C) 2009 Kristoffer Glembo <kristoffer@gaisler.com>, Aeroflex Gaisler AB
  11  */
  12
  13 #if defined(CONFIG_SERIAL_GRLIB_GAISLER_APBUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  14 #define SUPPORT_SYSRQ
  15 #endif
  16
  17 #include <linux/module.h>
  18 #include <linux/tty.h>
  19 #include <linux/tty_flip.h>
  20 #include <linux/ioport.h>
  21 #include <linux/init.h>
  22 #include <linux/serial.h>
  23 #include <linux/console.h>
  24 #include <linux/sysrq.h>
  25 #include <linux/kthread.h>
  26 #include <linux/device.h>
  27 #include <linux/of.h>
  28 #include <linux/of_device.h>
  29 #include <linux/of_platform.h>
  30 #include <linux/of_irq.h>
  31 #include <linux/platform_device.h>
  32 #include <linux/io.h>
  33 #include <linux/serial_core.h>
  34 #include <asm/irq.h>
  35
  36 #include "apbuart.h"
  37
  38 #define SERIAL_APBUART_MAJOR    TTY_MAJOR
  39 #define SERIAL_APBUART_MINOR    64
  40 #define UART_DUMMY_RSR_RX       0x8000  /* for ignore all read */
  41
  42 static void apbuart_tx_chars(struct uart_port *port);
  43
  44 static void apbuart_stop_tx(struct uart_port *port)
  45 {
  46         unsigned int cr;
  47
  48         cr = UART_GET_CTRL(port);
  49         cr &= ~UART_CTRL_TI;
  50         UART_PUT_CTRL(port, cr);
  51 }
  52
  53 static void apbuart_start_tx(struct uart_port *port)
  54 {
  55         unsigned int cr;
  56
  57         cr = UART_GET_CTRL(port);
  58         cr |= UART_CTRL_TI;
  59         UART_PUT_CTRL(port, cr);
  60
  61         if (UART_GET_STATUS(port) & UART_STATUS_THE)
  62                 apbuart_tx_chars(port);
  63 }
  64
  65 static void apbuart_stop_rx(struct uart_port *port)
  66 {
  67         unsigned int cr;
  68
  69         cr = UART_GET_CTRL(port);
  70         cr &= ~(UART_CTRL_RI);
  71         UART_PUT_CTRL(port, cr);
  72 }
  73
  74 static void apbuart_enable_ms(struct uart_port *port)
  75 {
  76         /* No modem status change interrupts for APBUART */
  77 }
  78
  79 static void apbuart_rx_chars(struct uart_port *port)
  80 {
  81         struct tty_struct *tty = port->state->port.tty;
  82         unsigned int status, ch, rsr, flag;
  83         unsigned int max_chars = port->fifosize;
  84
  85         status = UART_GET_STATUS(port);
  86
  87         while (UART_RX_DATA(status) && (max_chars--)) {
  88
  89                 ch = UART_GET_CHAR(port);
  90                 flag = TTY_NORMAL;
  91
  92                 port->icount.rx++;
  93
  94                 rsr = UART_GET_STATUS(port) | UART_DUMMY_RSR_RX;
  95                 UART_PUT_STATUS(port, 0);
  96                 if (rsr & UART_STATUS_ERR) {
  97
  98                         if (rsr & UART_STATUS_BR) {
  99                                 rsr &= ~(UART_STATUS_FE | UART_STATUS_PE);
 100                                 port->icount.brk++;
 101                                 if (uart_handle_break(port))
 102                                         goto ignore_char;
 103                         } else if (rsr & UART_STATUS_PE) {
 104                                 port->icount.parity++;
 105                         } else if (rsr & UART_STATUS_FE) {
 106                                 port->icount.frame++;
 107                         }
 108                         if (rsr & UART_STATUS_OE)
 109                                 port->icount.overrun++;
 110
 111                         rsr &= port->read_status_mask;
 112
 113                         if (rsr & UART_STATUS_PE)
 114                                 flag = TTY_PARITY;
 115                         else if (rsr & UART_STATUS_FE)
 116                                 flag = TTY_FRAME;
 117                 }
 118
 119                 if (uart_handle_sysrq_char(port, ch))
 120                         goto ignore_char;
 121
 122                 uart_insert_char(port, rsr, UART_STATUS_OE, ch, flag);
 123
 124
 125               ignore_char:
 126                 status = UART_GET_STATUS(port);
 127         }
 128
 129         tty_flip_buffer_push(tty);
 130 }
 131
 132 static void apbuart_tx_chars(struct uart_port *port)
 133 {
 134         struct circ_buf *xmit = &port->state->xmit;
 135         int count;
 136
 137         if (port->x_char) {
 138                 UART_PUT_CHAR(port, port->x_char);
 139                 port->icount.tx++;
 140                 port->x_char = 0;
 141                 return;
 142         }
 143
 144         if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
 145                 apbuart_stop_tx(port);
 146                 return;
 147         }
 148
 149         /* amba: fill FIFO */
 150         count = port->fifosize >> 1;
 151         do {
 152                 UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
 153                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 154                 port->icount.tx++;
 155                 if (uart_circ_empty(xmit))
 156                         break;
 157         } while (--count > 0);
 158
 159         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 160                 uart_write_wakeup(port);
 161
 162         if (uart_circ_empty(xmit))
 163                 apbuart_stop_tx(port);
 164 }
 165
 166 static irqreturn_t apbuart_int(int irq, void *dev_id)
 167 {
 168         struct uart_port *port = dev_id;
 169         unsigned int status;
 170
 171         spin_lock(&port->lock);
 172
 173         status = UART_GET_STATUS(port);
 174         if (status & UART_STATUS_DR)
 175                 apbuart_rx_chars(port);
 176         if (status & UART_STATUS_THE)
 177                 apbuart_tx_chars(port);
 178
 179         spin_unlock(&port->lock);
 180
 181         return IRQ_HANDLED;
 182 }
 183
 184 static unsigned int apbuart_tx_empty(struct uart_port *port)
 185 {
 186         unsigned int status = UART_GET_STATUS(port);
 187         return status & UART_STATUS_THE ? TIOCSER_TEMT : 0;
 188 }
 189
 190 static unsigned int apbuart_get_mctrl(struct uart_port *port)
 191 {
 192         /* The GRLIB APBUART handles flow control in hardware */
 193         return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
 194 }
 195
 196 static void apbuart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 197 {
 198         /* The GRLIB APBUART handles flow control in hardware */
 199 }
 200
 201 static void apbuart_break_ctl(struct uart_port *port, int break_state)
 202 {
 203         /* We don't support sending break */
 204 }
 205
 206 static int apbuart_startup(struct uart_port *port)
 207 {
 208         int retval;
 209         unsigned int cr;
 210
 211         /* Allocate the IRQ */
 212         retval = request_irq(port->irq, apbuart_int, 0, "apbuart", port);
 213         if (retval)
 214                 return retval;
 215
 216         /* Finally, enable interrupts */
 217         cr = UART_GET_CTRL(port);
 218         UART_PUT_CTRL(port,
 219                       cr | UART_CTRL_RE | UART_CTRL_TE |
 220                       UART_CTRL_RI | UART_CTRL_TI);
 221
 222         return 0;
 223 }
 224
 225 static void apbuart_shutdown(struct uart_port *port)
 226 {
 227         unsigned int cr;
 228
 229         /* disable all interrupts, disable the port */
 230         cr = UART_GET_CTRL(port);
 231         UART_PUT_CTRL(port,
 232                       cr & ~(UART_CTRL_RE | UART_CTRL_TE |
 233                              UART_CTRL_RI | UART_CTRL_TI));
 234
 235         /* Free the interrupt */
 236         free_irq(port->irq, port);
 237 }
 238
 239 static void apbuart_set_termios(struct uart_port *port,
 240                                 struct ktermios *termios, struct ktermios *old)
 241 {
 242         unsigned int cr;
 243         unsigned long flags;
 244         unsigned int baud, quot;
 245
 246         /* Ask the core to calculate the divisor for us. */
 247         baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
 248         if (baud == 0)
 249                 panic("invalid baudrate %i\n", port->uartclk / 16);
 250
 251         /* uart_get_divisor calc a *16 uart freq, apbuart is *8 */
 252         quot = (uart_get_divisor(port, baud)) * 2;
 253         cr = UART_GET_CTRL(port);
 254         cr &= ~(UART_CTRL_PE | UART_CTRL_PS);
 255
 256         if (termios->c_cflag & PARENB) {
 257                 cr |= UART_CTRL_PE;
 258                 if ((termios->c_cflag & PARODD))
 259                         cr |= UART_CTRL_PS;
 260         }
 261
 262         /* Enable flow control. */
 263         if (termios->c_cflag & CRTSCTS)
 264                 cr |= UART_CTRL_FL;
 265
 266         spin_lock_irqsave(&port->lock, flags);
 267
 268         /* Update the per-port timeout. */
 269         uart_update_timeout(port, termios->c_cflag, baud);
 270
 271         port->read_status_mask = UART_STATUS_OE;
 272         if (termios->c_iflag & INPCK)
 273                 port->read_status_mask |= UART_STATUS_FE | UART_STATUS_PE;
 274
 275         /* Characters to ignore */
 276         port->ignore_status_mask = 0;
 277         if (termios->c_iflag & IGNPAR)
 278                 port->ignore_status_mask |= UART_STATUS_FE | UART_STATUS_PE;
 279
 280         /* Ignore all characters if CREAD is not set. */
 281         if ((termios->c_cflag & CREAD) == 0)
 282                 port->ignore_status_mask |= UART_DUMMY_RSR_RX;
 283
 284         /* Set baud rate */
 285         quot -= 1;
 286         UART_PUT_SCAL(port, quot);
 287         UART_PUT_CTRL(port, cr);
 288
 289         spin_unlock_irqrestore(&port->lock, flags);
 290 }
 291
 292 static const char *apbuart_type(struct uart_port *port)
 293 {
 294         return port->type == PORT_APBUART ? "GRLIB/APBUART" : NULL;
 295 }
 296
 297 static void apbuart_release_port(struct uart_port *port)
 298 {
 299         release_mem_region(port->mapbase, 0x100);
 300 }
 301
 302 static int apbuart_request_port(struct uart_port *port)
 303 {
 304         return request_mem_region(port->mapbase, 0x100, "grlib-apbuart")
 305             != NULL ? 0 : -EBUSY;
 306         return 0;
 307 }
 308
 309 /* Configure/autoconfigure the port */
 310 static void apbuart_config_port(struct uart_port *port, int flags)
 311 {
 312         if (flags & UART_CONFIG_TYPE) {
 313                 port->type = PORT_APBUART;
 314                 apbuart_request_port(port);
 315         }
 316 }
 317
 318 /* Verify the new serial_struct (for TIOCSSERIAL) */
 319 static int apbuart_verify_port(struct uart_port *port,
 320                                struct serial_struct *ser)
 321 {
 322         int ret = 0;
 323         if (ser->type != PORT_UNKNOWN && ser->type != PORT_APBUART)
 324                 ret = -EINVAL;
 325         if (ser->irq < 0 || ser->irq >= NR_IRQS)
 326                 ret = -EINVAL;
 327         if (ser->baud_base < 9600)
 328                 ret = -EINVAL;
 329         return ret;
 330 }
 331
 332 static struct uart_ops grlib_apbuart_ops = {
 333         .tx_empty = apbuart_tx_empty,
 334         .set_mctrl = apbuart_set_mctrl,
 335         .get_mctrl = apbuart_get_mctrl,
 336         .stop_tx = apbuart_stop_tx,
 337         .start_tx = apbuart_start_tx,
 338         .stop_rx = apbuart_stop_rx,
 339         .enable_ms = apbuart_enable_ms,
 340         .break_ctl = apbuart_break_ctl,
 341         .startup = apbuart_startup,
 342         .shutdown = apbuart_shutdown,
 343         .set_termios = apbuart_set_termios,
 344         .type = apbuart_type,
 345         .release_port = apbuart_release_port,
 346         .request_port = apbuart_request_port,
 347         .config_port = apbuart_config_port,
 348         .verify_port = apbuart_verify_port,
 349 };
 350
 351 static struct uart_port grlib_apbuart_ports[UART_NR];
 352 static struct device_node *grlib_apbuart_nodes[UART_NR];
 353
 354 static int apbuart_scan_fifo_size(struct uart_port *port, int portnumber)
 355 {
 356         int ctrl, loop = 0;
 357         int status;
 358         int fifosize;
 359         unsigned long flags;
 360
 361         ctrl = UART_GET_CTRL(port);
 362
 363         /*
 364          * Enable the transceiver and wait for it to be ready to send data.
 365          * Clear interrupts so that this process will not be externally
 366          * interrupted in the middle (which can cause the transceiver to
 367          * drain prematurely).
 368          */
 369
 370         local_irq_save(flags);
 371
 372         UART_PUT_CTRL(port, ctrl | UART_CTRL_TE);
 373
 374         while (!UART_TX_READY(UART_GET_STATUS(port)))
 375                 loop++;
 376
 377         /*
 378          * Disable the transceiver so data isn't actually sent during the
 379          * actual test.
 380          */
 381
 382         UART_PUT_CTRL(port, ctrl & ~(UART_CTRL_TE));
 383
 384         fifosize = 1;
 385         UART_PUT_CHAR(port, 0);
 386
 387         /*
 388          * So long as transmitting a character increments the tranceivier FIFO
 389          * length the FIFO must be at least that big. These bytes will
 390          * automatically drain off of the FIFO.
 391          */
 392
 393         status = UART_GET_STATUS(port);
 394         while (((status >> 20) & 0x3F) == fifosize) {
 395                 fifosize++;
 396                 UART_PUT_CHAR(port, 0);
 397                 status = UART_GET_STATUS(port);
 398         }
 399
 400         fifosize--;
 401
 402         UART_PUT_CTRL(port, ctrl);
 403         local_irq_restore(flags);
 404
 405         if (fifosize == 0)
 406                 fifosize = 1;
 407
 408         return fifosize;
 409 }
 410
 411 static void apbuart_flush_fifo(struct uart_port *port)
 412 {
 413         int i;
 414
 415         for (i = 0; i < port->fifosize; i++)
 416                 UART_GET_CHAR(port);
 417 }
 418
 419
 420 /* ======================================================================== */
 421 /* Console driver, if enabled                                               */
 422 /* ======================================================================== */
 423
 424 #ifdef CONFIG_SERIAL_GRLIB_GAISLER_APBUART_CONSOLE
 425
 426 static void apbuart_console_putchar(struct uart_port *port, int ch)
 427 {
 428         unsigned int status;
 429         do {
 430                 status = UART_GET_STATUS(port);
 431         } while (!UART_TX_READY(status));
 432         UART_PUT_CHAR(port, ch);
 433 }
 434
 435 static void
 436 apbuart_console_write(struct console *co, const char *s, unsigned int count)
 437 {
 438         struct uart_port *port = &grlib_apbuart_ports[co->index];
 439         unsigned int status, old_cr, new_cr;
 440
 441         /* First save the CR then disable the interrupts */
 442         old_cr = UART_GET_CTRL(port);
 443         new_cr = old_cr & ~(UART_CTRL_RI | UART_CTRL_TI);
 444         UART_PUT_CTRL(port, new_cr);
 445
 446         uart_console_write(port, s, count, apbuart_console_putchar);
 447
 448         /*
 449          *      Finally, wait for transmitter to become empty
 450          *      and restore the TCR
 451          */
 452         do {
 453                 status = UART_GET_STATUS(port);
 454         } while (!UART_TX_READY(status));
 455         UART_PUT_CTRL(port, old_cr);
 456 }
 457
 458 static void __init
 459 apbuart_console_get_options(struct uart_port *port, int *baud,
 460                             int *parity, int *bits)
 461 {
 462         if (UART_GET_CTRL(port) & (UART_CTRL_RE | UART_CTRL_TE)) {
 463
 464                 unsigned int quot, status;
 465                 status = UART_GET_STATUS(port);
 466
 467                 *parity = 'n';
 468                 if (status & UART_CTRL_PE) {
 469                         if ((status & UART_CTRL_PS) == 0)
 470                                 *parity = 'e';
 471                         else
 472                                 *parity = 'o';
 473                 }
 474
 475                 *bits = 8;
 476                 quot = UART_GET_SCAL(port) / 8;
 477                 *baud = port->uartclk / (16 * (quot + 1));
 478         }
 479 }
 480
 481 static int __init apbuart_console_setup(struct console *co, char *options)
 482 {
 483         struct uart_port *port;
 484         int baud = 38400;
 485         int bits = 8;
 486         int parity = 'n';
 487         int flow = 'n';
 488
 489         pr_debug("apbuart_console_setup co=%p, co->index=%i, options=%s\n",
 490                  co, co->index, options);
 491
 492         /*
 493          * Check whether an invalid uart number has been specified, and
 494          * if so, search for the first available port that does have
 495          * console support.
 496          */
 497         if (co->index >= grlib_apbuart_port_nr)
 498                 co->index = 0;
 499
 500         port = &grlib_apbuart_ports[co->index];
 501
 502         spin_lock_init(&port->lock);
 503
 504         if (options)
 505                 uart_parse_options(options, &baud, &parity, &bits, &flow);
 506         else
 507                 apbuart_console_get_options(port, &baud, &parity, &bits);
 508
 509         return uart_set_options(port, co, baud, parity, bits, flow);
 510 }
 511
 512 static struct uart_driver grlib_apbuart_driver;
 513
 514 static struct console grlib_apbuart_console = {
 515         .name = "ttyS",
 516         .write = apbuart_console_write,
 517         .device = uart_console_device,
 518         .setup = apbuart_console_setup,
 519         .flags = CON_PRINTBUFFER,
 520         .index = -1,
 521         .data = &grlib_apbuart_driver,
 522 };
 523
 524
 525 static int grlib_apbuart_configure(void);
 526
 527 static int __init apbuart_console_init(void)
 528 {
 529         if (grlib_apbuart_configure())
 530                 return -ENODEV;
 531         register_console(&grlib_apbuart_console);
 532         return 0;
 533 }
 534
 535 console_initcall(apbuart_console_init);
 536
 537 #define APBUART_CONSOLE (&grlib_apbuart_console)
 538 #else
 539 #define APBUART_CONSOLE NULL
 540 #endif
 541
 542 static struct uart_driver grlib_apbuart_driver = {
 543         .owner = THIS_MODULE,
 544         .driver_name = "serial",
 545         .dev_name = "ttyS",
 546         .major = SERIAL_APBUART_MAJOR,
 547         .minor = SERIAL_APBUART_MINOR,
 548         .nr = UART_NR,
 549         .cons = APBUART_CONSOLE,
 550 };
 551
 552
 553 /* ======================================================================== */
 554 /* OF Platform Driver                                                       */
 555 /* ======================================================================== */
 556
 557 static int __devinit apbuart_probe(struct platform_device *op)
 558 {
 559         int i;
 560         struct uart_port *port = NULL;
 561
 562         for (i = 0; i < grlib_apbuart_port_nr; i++) {
 563                 if (op->dev.of_node == grlib_apbuart_nodes[i])
 564                         break;
 565         }
 566
 567         port = &grlib_apbuart_ports[i];
 568         port->dev = &op->dev;
 569         port->irq = op->archdata.irqs[0];
 570
 571         uart_add_one_port(&grlib_apbuart_driver, (struct uart_port *) port);
 572
 573         apbuart_flush_fifo((struct uart_port *) port);
 574
 575         printk(KERN_INFO "grlib-apbuart at 0x%llx, irq %d\n",
 576                (unsigned long long) port->mapbase, port->irq);
 577         return 0;
 578 }
 579
 580 static struct of_device_id __initdata apbuart_match[] = {
 581         {
 582          .name = "GAISLER_APBUART",
 583          },
 584         {
 585          .name = "01_00c",
 586          },
 587         {},
 588 };
 589
 590 static struct platform_driver grlib_apbuart_of_driver = {
 591         .probe = apbuart_probe,
 592         .driver = {
 593                 .owner = THIS_MODULE,
 594                 .name = "grlib-apbuart",
 595                 .of_match_table = apbuart_match,
 596         },
 597 };
 598
 599
 600 static int grlib_apbuart_configure(void)
 601 {
 602         struct device_node *np;
 603         int line = 0;
 604
 605         for_each_matching_node(np, apbuart_match) {
 606                 const int *ampopts;
 607                 const u32 *freq_hz;
 608                 const struct amba_prom_registers *regs;
 609                 struct uart_port *port;
 610                 unsigned long addr;
 611
 612                 ampopts = of_get_property(np, "ampopts", NULL);
 613                 if (ampopts && (*ampopts == 0))
 614                         continue; /* Ignore if used by another OS instance */
 615                 regs = of_get_property(np, "reg", NULL);
 616                 /* Frequency of APB Bus is frequency of UART */
 617                 freq_hz = of_get_property(np, "freq", NULL);
 618
 619                 if (!regs || !freq_hz || (*freq_hz == 0))
 620                         continue;
 621
 622                 grlib_apbuart_nodes[line] = np;
 623
 624                 addr = regs->phys_addr;
 625
 626                 port = &grlib_apbuart_ports[line];
 627
 628                 port->mapbase = addr;
 629                 port->membase = ioremap(addr, sizeof(struct grlib_apbuart_regs_map));
 630                 port->irq = 0;
 631                 port->iotype = UPIO_MEM;
 632                 port->ops = &grlib_apbuart_ops;
 633                 port->flags = UPF_BOOT_AUTOCONF;
 634                 port->line = line;
 635                 port->uartclk = *freq_hz;
 636                 port->fifosize = apbuart_scan_fifo_size((struct uart_port *) port, line);
 637                 line++;
 638
 639                 /* We support maximum UART_NR uarts ... */
 640                 if (line == UART_NR)
 641                         break;
 642         }
 643
 644         grlib_apbuart_driver.nr = grlib_apbuart_port_nr = line;
 645         return line ? 0 : -ENODEV;
 646 }
 647
 648 static int __init grlib_apbuart_init(void)
 649 {
 650         int ret;
 651
 652         /* Find all APBUARTS in device the tree and initialize their ports */
 653         ret = grlib_apbuart_configure();
 654         if (ret)
 655                 return ret;
 656
 657         printk(KERN_INFO "Serial: GRLIB APBUART driver\n");
 658
 659         ret = uart_register_driver(&grlib_apbuart_driver);
 660
 661         if (ret) {
 662                 printk(KERN_ERR "%s: uart_register_driver failed (%i)\n",
 663                        __FILE__, ret);
 664                 return ret;
 665         }
 666
 667         ret = platform_driver_register(&grlib_apbuart_of_driver);
 668         if (ret) {
 669                 printk(KERN_ERR
 670                        "%s: platform_driver_register failed (%i)\n",
 671                        __FILE__, ret);
 672                 uart_unregister_driver(&grlib_apbuart_driver);
 673                 return ret;
 674         }
 675
 676         return ret;
 677 }
 678
 679 static void __exit grlib_apbuart_exit(void)
 680 {
 681         int i;
 682
 683         for (i = 0; i < grlib_apbuart_port_nr; i++)
 684                 uart_remove_one_port(&grlib_apbuart_driver,
 685                                      &grlib_apbuart_ports[i]);
 686
 687         uart_unregister_driver(&grlib_apbuart_driver);
 688         platform_driver_unregister(&grlib_apbuart_of_driver);
 689 }
 690
 691 module_init(grlib_apbuart_init);
 692 module_exit(grlib_apbuart_exit);
 693
 694 MODULE_AUTHOR("Aeroflex Gaisler AB");
 695 MODULE_DESCRIPTION("GRLIB APBUART serial driver");
 696 MODULE_VERSION("2.1");
 697 MODULE_LICENSE("GPL");