Staging: rt2860: remove dead LEAP_SUPPORT code
[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / net / mac80211 / pm.c
blob7a549f9deb967c1acbcf4ce1dbc41d28bcbefb4d
1 #include <net/mac80211.h>
2 #include <net/rtnetlink.h>
4 #include "ieee80211_i.h"
5 #include "mesh.h"
6 #include "driver-ops.h"
7 #include "led.h"
9 int __ieee80211_suspend(struct ieee80211_hw *hw)
11 struct ieee80211_local *local = hw_to_local(hw);
12 struct ieee80211_sub_if_data *sdata;
13 struct ieee80211_if_init_conf conf;
14 struct sta_info *sta;
15 unsigned long flags;
17 ieee80211_scan_cancel(local);
19 ieee80211_stop_queues_by_reason(hw,
20 IEEE80211_QUEUE_STOP_REASON_SUSPEND);
22 /* flush out all packets */
23 synchronize_net();
25 local->quiescing = true;
26 /* make quiescing visible to timers everywhere */
27 mb();
29 flush_workqueue(local->hw.workqueue);
31 /* Don't try to run timers while suspended. */
32 del_timer_sync(&local->sta_cleanup);
35 * Note that this particular timer doesn't need to be
36 * restarted at resume.
38 cancel_work_sync(&local->dynamic_ps_enable_work);
39 del_timer_sync(&local->dynamic_ps_timer);
41 /* disable keys */
42 list_for_each_entry(sdata, &local->interfaces, list)
43 ieee80211_disable_keys(sdata);
45 /* Tear down aggregation sessions */
47 rcu_read_lock();
49 if (hw->flags & IEEE80211_HW_AMPDU_AGGREGATION) {
50 list_for_each_entry_rcu(sta, &local->sta_list, list) {
51 set_sta_flags(sta, WLAN_STA_SUSPEND);
52 ieee80211_sta_tear_down_BA_sessions(sta);
56 rcu_read_unlock();
58 /* flush again, in case driver queued work */
59 flush_workqueue(local->hw.workqueue);
61 /* stop hardware - this must stop RX */
62 if (local->open_count) {
63 ieee80211_led_radio(local, false);
64 drv_stop(local);
67 /* remove STAs */
68 spin_lock_irqsave(&local->sta_lock, flags);
69 list_for_each_entry(sta, &local->sta_list, list) {
70 if (local->ops->sta_notify) {
71 sdata = sta->sdata;
72 if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
73 sdata = container_of(sdata->bss,
74 struct ieee80211_sub_if_data,
75 u.ap);
77 drv_sta_notify(local, &sdata->vif, STA_NOTIFY_REMOVE,
78 &sta->sta);
81 mesh_plink_quiesce(sta);
83 spin_unlock_irqrestore(&local->sta_lock, flags);
85 /* remove all interfaces */
86 list_for_each_entry(sdata, &local->interfaces, list) {
87 switch(sdata->vif.type) {
88 case NL80211_IFTYPE_STATION:
89 ieee80211_sta_quiesce(sdata);
90 break;
91 case NL80211_IFTYPE_ADHOC:
92 ieee80211_ibss_quiesce(sdata);
93 break;
94 case NL80211_IFTYPE_MESH_POINT:
95 ieee80211_mesh_quiesce(sdata);
96 break;
97 case NL80211_IFTYPE_AP_VLAN:
98 case NL80211_IFTYPE_MONITOR:
99 /* don't tell driver about this */
100 continue;
101 default:
102 break;
105 if (!netif_running(sdata->dev))
106 continue;
108 conf.vif = &sdata->vif;
109 conf.type = sdata->vif.type;
110 conf.mac_addr = sdata->dev->dev_addr;
111 drv_remove_interface(local, &conf);
114 local->suspended = true;
115 local->quiescing = false;
117 return 0;
121 * __ieee80211_resume() is a static inline which just calls
122 * ieee80211_reconfig(), which is also needed for hardware
123 * hang/firmware failure/etc. recovery.